The fsl,panel property is deprecated and we should use the new
of_graph dt bindings to describe the relationship between the DCU
controller and the panel.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
add of_graph dt nodes to describe the panel, and removed
"fsl,panel" property
Signed-off-by: Meng Yi <meng.yi@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on NXP i.MX53 SoC.
https://inversepath.com/usbarmory
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Inverse Path is an information security consulting company:
https://inversepath.com
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
WaRP7 has a BCM43430 Bluetooth chip.
Add support for it.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IMX6UL GEA M6UL modules are system on module solutions manufactured
by Engicam with following characteristics:
Processor Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
RAM 128MB, 16-bit DDR3
NAND SLC 256MB
Power supply Single 5V
MAX LCD RES up to WXGA, 1366x768
and more info at
http://www.engicam.com/prodotti/embedded/som/sodimm/gea-m6ul
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Matteo Lisi <matteo.lisi@engicam.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators. This also synchronize
the name of the +3.3V regulator with the one used in the Colibri
VF50/VF61 device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move SD-card definition to module level. While at it, also disable
write-protect since the Colibri standard does not define a pin for
SD-Card write-protection.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bindings for the Vivante GC400T GPU found in the i.MX6SX.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ul-pico has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
At power on, pca953x GPIO pins are configured as input and may cause
unexpected interrupts. Configure the unused pins as GPO low to
avoid unexpected interrupts.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7s-warpd has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Warp7 has a BCM43430 Wifi chip connected to the USDHC1 port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
warp7 has a sgtl5000 audio codec.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only i.MX 7Dual SoC supports CPU frequencies of up to 1GHz. The i.MX
7Solo can run with up to 800MHz and does so without making use of DVFS
usually. While the device tree clearly specified a too fast operating
point for i.MX 7Solo, the kernel did not used it in practise so far
because the CPUfreq driver does not get loaded on i.MX 7Solo devices
(since the fsl,imx7s compatible string is not in the list of devices
making use of the cpufreq-dt driver...).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for MPL3115 NXP pressure sensor.
Tested by reading temperature and pressure:
$ cat /sys/bus/iio/devices/iio:device0/in_temp_raw
$ cat /sys/bus/iio/devices/iio:device0/in_pressure_raw
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These device trees add support for TS-4900 by Technologic Systems.
More details here:
http://wiki.embeddedarm.com/wiki/TS-4900
Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the documentation for the TS-4900 by Technologic Systems.
Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* small form factor (35x70mm)
* 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
* 256MB NAND flash (4GB option)
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* 1x miniPCI socket (with PCIe, USB, SIM)
* 1x microSD socket
* 1x SIM socket
* Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
* analog CVBS video in
* GPS (optional uBlox EVA-M8M)
* Application headers:
- 2x TTL UART (TX/RX)
- 4x TTL GPIO (3x configurable as PWM)
- 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
* Front panel connectors:
- micro-HDMI audio/video out
- 1x user programmable LED
- 1x configurable user pushbutton
- 1x USB OTG
See http://www.gateworks.com for more info
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7 as a GICv2, hence its CPU interface register map (the
second register region) is 8kB long. Add the VGIC maintenance
interrupt which allows to use the new VGIC driver.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since we have a SoC level node we should make use of it and have
all nodes which are within the SoC, inside that node. This also
saves an extra interrupt-parent properties. While at it, also
order the Coresight nodes according to register addresses.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We have the following messages that tell csi devices are not used:
imx-ipuv3 18000000.ipu: no port@0 node in /soc/ipu@18000000, not using CSI0
imx-ipuv3 18000000.ipu: no port@1 node in /soc/ipu@18000000, not using CSI1
So we add them in the common device tree to make CSI ports available on
imx53 boards.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to use sdma with UART, we need to add DMA configuration in device tree.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ul-pico-hobbit has a bcm4343 wifi chip connected to usdhc2 port.
Add support for it.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SoC internal regulators for the CPU and the SoC come from the
DA9063 vdd_core and vdd_soc. Add this relationship to the device tree
so that the voltage drop on the SoC internal LDO regulators can be
minimized.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Several dts files set a bit in the SPEED field for pads
RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there
doesn't have an effect and the bit reads as zero.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
bc677ff42e adds a device-tree property
to specify that an external watchdog reset is used to reset other
portions of the board and not just the IMX6 SoC.
This adds the property to the proper watchdog as well as the pinmux for
the Gateworks Ventana boards that use this external watchdog reset to
reset the PMIC which will reset all the PMIC power rails and not just
a chip-level IMX6 reset. This helps to work around various system issues
that can cause a hang when coming out of reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull more block fixes from Jens Axboe:
"As mentioned in the pull the other day, a few more fixes for this
round, all related to the bio op changes in this series.
Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf. I
wanted to do that change right after or right before -rc1, so that
risk of conflict was reduced. I just rebased the series on top of
current master, and no new ->bi_rw usage has snuck in"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: rename bio bi_rw to bi_opf
target: iblock_execute_sync_cache() should use bio_set_op_attrs()
mm: make __swap_writepage() use bio_set_op_attrs()
block/mm: make bdev_ops->rw_page() take a bool for read/write
Pull drm zpos property support from Dave Airlie:
"This tree was waiting on some media stuff I hadn't had time to get a
stable branchpoint off, so I just waited until it was all in your tree
first.
It's been around a bit on the list and shouldn't affect anything
outside adding the generic API and moving some ARM drivers to using
it"
* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
drm: rcar: use generic code for managing zpos plane property
drm/exynos: use generic code for managing zpos plane property
drm: sti: use generic zpos for plane
drm: add generic zpos property
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
The original commit missed this function, it needs to mark it a
write flush.
Cc: Mike Christie <mchristi@redhat.com>
Fixes: e742fc32fc ("target: use bio op accessors")
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit abf545484d changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
"make help" if sphinx isn't present.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iD7L
-----END PGP SIGNATURE-----
Merge tag 'doc-4.8-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Three fixes for the docs build, including removing an annoying warning
on 'make help' if sphinx isn't present"
* tag 'doc-4.8-fixes' of git://git.lwn.net/linux:
DocBook: use DOCBOOKS="" to ignore DocBooks instead of IGNORE_DOCBOOKS=1
Documenation: update cgroup's document path
Documentation/sphinx: do not warn about missing tools in 'make help'
First off, the intention of this pull is to declare that I'll be the
binfmt_misc maintainer (mainly on the grounds of you touched it last,
it's yours). There's no MAINTAINERS entry, but get_maintainers.pl
will now finger me.
The update itself is to allow architecture emulation containers to
function such that the emulation binary can be housed outside the
container itself. The container and fs parts both have acks from
relevant experts.
The change is user visible. To use the new feature you have to add an
F option to your binfmt_misc configuration. However, the existing
tools, like systemd-binfmt work with this without modification.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6OjN
-----END PGP SIGNATURE-----
Merge tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc
Pull binfmt_misc update from James Bottomley:
"This update is to allow architecture emulation containers to function
such that the emulation binary can be housed outside the container
itself. The container and fs parts both have acks from relevant
experts.
To use the new feature you have to add an F option to your binfmt_misc
configuration"
From the docs:
"The usual behaviour of binfmt_misc is to spawn the binary lazily when
the misc format file is invoked. However, this doesn't work very well
in the face of mount namespaces and changeroots, so the F mode opens
the binary as soon as the emulation is installed and uses the opened
image to spawn the emulator, meaning it is always available once
installed, regardless of how the environment changes"
* tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc:
binfmt_misc: add F option description to documentation
binfmt_misc: add persistent opened binary handler for containers
fs: add filp_clone_open API
In most cases, EPERM is returned on immutable inode, and there're only a
few places returning EACCES. I noticed this when running LTP on
overlayfs, setxattr03 failed due to unexpected EACCES on immutable
inode.
So converting all EACCES to EPERM on immutable inode.
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more vfs updates from Al Viro:
"Assorted cleanups and fixes.
In the "trivial API change" department - ->d_compare() losing 'parent'
argument"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cachefiles: Fix race between inactivating and culling a cache object
9p: use clone_fid()
9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
vfs: make dentry_needs_remove_privs() internal
vfs: remove file_needs_remove_privs()
vfs: fix deadlock in file_remove_privs() on overlayfs
get rid of 'parent' argument of ->d_compare()
cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
affs ->d_compare(): don't bother with ->d_inode
fold _d_rehash() and __d_rehash() together
fold dentry_rcuwalk_invalidate() into its only remaining caller
