Fixes the following sparse warning:
drivers/regulator/bd9571mwv-regulator.c:220:1: warning:
symbol 'dev_attr_backup_mode' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add enable/disable support for switch regulators on pfuze100.
Based on commit 5fe156f1ca ("regulator: pfuze100: add enable/disable for
switch") which is reverted due to boot regressions by commit 464a5686e6
("regulator: Revert "regulator: pfuze100: add enable/disable for switch"").
Disabling the switch regulators will only be done if the user specifies
"fsl,pfuze-support-disable-sw" in its device tree to keep backward
compatibility with current dtb's [1].
[1] https://patchwork.kernel.org/patch/10490381/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch error:
ERROR: code indent should use tabs where possible
+ { }$
Fixes: ca5cd8c940 ("regulator: qcom_spmi: Add support for pmi8994")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch error:
ERROR: do not initialise statics to NULL
+static struct regmap *saw_regmap = NULL;
Fixes: 0caecaa872 ("regulator: qcom_spmi: Add support for SAW")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have just assigned saw_regmap, and since the error message
refers to saw_regmap, it feels safe to assume that it is saw_regmap,
and not regmap, that should be checked for errors.
Fixes: 0caecaa872 ("regulator: qcom_spmi: Add support for SAW")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
For of_find_node_by_name(), you typically pass what the previous call
returned. Therefore, of_find_node_by_name() increases the refcount of
the returned node, and decreases the refcount of the node passed as the
first argument.
of_find_node_by_name() is incorrectly used, and produces a warning.
Fix the warning by using the more suitable function
of_get_child_by_name().
Also add a missing of_node_put() for the returned value, since this was
previously being leaked.
OF: ERROR: Bad of_node_put() on /soc/qcom,spmi@400f000/pmic@3/regulators
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 4.18.0-rc4-00223-gefd7b360b70e #12
Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
Call trace:
dump_backtrace+0x0/0x1a8
show_stack+0x14/0x20
dump_stack+0x90/0xb4
of_node_release+0x74/0x78
kobject_put+0x90/0x1f0
of_node_put+0x14/0x20
of_find_node_by_name+0x80/0xd8
qcom_spmi_regulator_probe+0x30c/0x508
Fixes: 0caecaa872 ("regulator: qcom_spmi: Add support for SAW")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the existing support for backup mode to toggle power switches.
With a toggle power switch (or level signal), the following steps must
be followed exactly:
1. Configure PMIC for backup mode, to change the role of the
accessory power switch from a power switch to a wake-up switch,
2. Switch accessory power switch off, to prepare for system suspend,
which is a manual step not controlled by software,
3. Suspend system,
4. Switch accessory power switch on, to resume the system.
Hence the PMIC is configured for backup mode when "on" or "1" is written
to the PMIC's "backup_mode" virtual file in sysfs. Conversely, writing
"off" or "0" reverts the role of the accessory switch to a power
switch.
Unlike with momentary switches, backup mode is not enabled by default,
as enabling it prevents the board from being powered off using the power
switch, which may confuse the user.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the BD9571MWV PMIC driver uses the standard "wake_up" sysfs
file to control enablement of DDR Backup Mode.
However, configuring DDR Backup Mode is not really equivalent to
configuring the PMIC as a wake-up source. To avoid confusion, use a
custom "backup_mode" attribute file in sysfs instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit to add support for regulators implemented in UniPhier SoCs.
This supports USB VBUS only.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code generates a static cehcker warnings because "rid < 0"
is always false:
drivers/regulator/max8997-regulator.c:169 max8997_list_voltage()
warn: condition is always false
The problem is that because of type promotion, if "rid" is negative the
comparison against ARRAY_SIZE() is type promoted to size_t and it's
treated as a very high positive value. I've changed the order of the
checks so now everyone is happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a device link between the consumer and the driver so that
the consumer is not suspended before the driver. The goal is to avoid
implementing suspend_late ops in regulator drivers.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change suspend_late ops to suspend normal ops. The goal is to avoid
requesting all the regulator drivers to be operational in suspend late
phase.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the LDOs present only on DA9063 at the end of the list, so that
the DA9063L can simply indicate less LDOs and still share the list of
regulators with DA9063.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The model number stored in the struct da9063 is the same for all
variants of the da9063 since it is the chip ID, which is always
the same. Replace that with a separate identifier instead, which
allows us to discern the DA9063 variants by setting the type
based on either DT match or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PMIC_DA9063 is a complete misnomer, it denotes the value of the
DA9063 chip ID register, so rename it as such. It is also the value
of chip ID register of DA9063L though, so drop the enum as all the
DA9063 "models" share the same chip ID and thus the distinction will
have to be made using DT or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This reverts commit 5fe156f1ca.
Commit 5fe156f1ca ("regulator: pfuze100: add enable/disable for switch")
causes boot regression on some platforms such as imx6sl-evk and
imx6sll-evk.
After this commit the SW4 regulator will be turned
off and since it supplies the DDR voltage on these boards, a
kernel hang is observed.
Revert it to avoid breaking old dtb's.
Fixes: 5fe156f1ca ("regulator: pfuze100: add enable/disable for switch")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Address issues spotted by Andy Shevchenko during review of original patch
No functional changes intended
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the enable GPIO is being looked up on the regulator
device itself but that does not have its own DT node, this causes
the lookup to fail and the regulator not to get its GPIO. The DT
node is shared across the whole MFD and as such the lookup needs
to happen on that parent device. Moving the lookup to the parent
device also means devres can no longer be used as the life time
would attach to the wrong device.
Additionally, the enable GPIO is active high so we should be passing
GPIOD_OUT_LOW to ensure the regulator starts in its off state allowing
the driver to enable it when it is ready.
Fixes: e1739e86f0 ("regulator: arizona-ldo1: Look up a descriptor and pass to the core")
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This extends the pfuze100 driver with pfuze3001 support.
Latest datasheet:
https://www.nxp.com/docs/en/data-sheet/PF3001.pdf
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a lot of core work this time around, though not 100% successful.
We gained support for runtime mode changes thanks to David Collins and
improved support for write only regulators (ones where we can't read
back the configuration) from Douglas Anderson.
There's been quite a bit of work from Linus Walleij on converting from
specfying GPIOs by numbers to descriptors. Sadly the testing turned out
to be less good than we had hoped and so a lot of this had to be
reverted.
We also have the start of updates to use coupled regulators from Maciej
Purski, unfortunately there are further problems there so the last
couple of patches have been reverted.
We also have new drivers for BD71837 and SY8106A devices, SAW regulators
on Qualcomm SPMI and dropped support for some preproduction chips
that never made it to market from the AB8500 driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlsarcETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0B4HB/9MFV/MK7Hw2hsVCX3qWTiH4tJ/X0MG
tGz1PfmbH0CJ9ly5g+rvCoT+1/s7BydKzi1cd1RHnimBv2U1XagwSny3LNEcJs2Q
pmhpGViakkQI/Y2h+u/j0Jk1nE+jTiKk+1ozUB7YnPekrGyQlf7TMhvKOLTvLKyX
56jdNxcW0MgSnXV2N6y4NpWhgvrQwvKjacTxV5iX7WP2rnK2WNFeG7Q859buhtI0
znRi+tO5hZsw5T44ickdPfotZn+i5o7MYLCkkaA2h1EwtpbYwVINfUjp3KtuyFhH
3B9GmCsjjN2Z2eInnkpzWfVXK2S1Vlp6+ka2FSs+U/4rVdd3Bw2KkblS
=Ftua
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite a lot of core work this time around, though not 100% successful.
We gained support for runtime mode changes thanks to David Collins and
improved support for write only regulators (ones where we can't read
back the configuration) from Douglas Anderson.
There's been quite a bit of work from Linus Walleij on converting from
specfying GPIOs by numbers to descriptors. Sadly the testing turned
out to be less good than we had hoped and so a lot of this had to be
reverted.
We also have the start of updates to use coupled regulators from
Maciej Purski, unfortunately there are further problems there so the
last couple of patches have been reverted.
We also have new drivers for BD71837 and SY8106A devices, SAW
regulators on Qualcomm SPMI and dropped support for some preproduction
chips that never made it to market from the AB8500 driver"
* tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (57 commits)
regulator: gpio: Revert
ARM: pxa, regulator: fix building ezx e680
regulator: Revert coupled regulator support again
regulator: wm8994: Fix shared GPIOs
regulator: max77686: Fix shared GPIOs
regulator: bd71837: BD71837 PMIC regulator driver
regulator: bd71837: Devicetree bindings for BD71837 regulators
regulator: gpio: Get enable GPIO using GPIO descriptor
regulator: fixed: Convert to use GPIO descriptor only
regulator: s2mps11: Fix boot on Odroid XU3
dt-bindings: qcom_spmi: Document SAW support
regulator: qcom_spmi: Add support for SAW
regulator: tps65090: Pass descriptor instead of GPIO number
regulator: s5m8767: Pass descriptor instead of GPIO number
regulator: pfuze100: Delete reference to ena_gpio
regulator: max8952: Pass descriptor instead of GPIO number
regulator: lp8788-ldo: Pass descriptor instead of GPIO number
regulator: lm363x: Pass descriptor instead of GPIO number
regulator: max8973: Pass descriptor instead of GPIO number
regulator: mc13xxx-core: Switch to SPDX identifier
...
regulator: fixed/gpio: Revert GPIO descriptor changes due to platform breakage
Commit 6059577cb2 "regulator: fixed: Convert to use GPIO descriptor
only" broke at least the ams-delta platform since the lookup tables
added to the board files use the function name "enable" while the driver
uses NULL causing the regulator to not acquire and control the enable
GPIOs. Revert that and a couple of other commits that are caught up
with it to fix the issue:
2b6c00c157 "ARM: pxa, regulator: fix building ezx e680"
6059577cb2 "regulator: fixed: Convert to use GPIO descriptor only"
37bed97f00 "regulator: gpio: Get enable GPIO using GPIO descriptor"
Reported-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Revert the last two commits of the voltage coupling mechanism patch set:
456e7cdf3b regulator: core: Change voltage setting path
696861761a regulator: core: Add voltage balancing mechanism
as they broke boot on OMAP again.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 3c6b38d45f "regulator: wm8994: Pass
descriptor instead of GPIO number" as it has problems with shared
GPIOs similar to that on s2mps11.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit c89c00e2b8 "regulator: max77686: Pass descriptor
instead of GPIO number" as it has problems with shared GPIOs similar to
that on s2mps11.
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for controlling the 8 bucks and 7 LDOs the PMIC contains.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We augment the GPIO regulator to get the *enable* regulator
GPIO line (not the other lines) using a descriptor rather than
a global number.
We then pass this into the regulator core which has been
prepared to hande enable descriptors in a separate patch.
Switch over the two boardfiles using this facility and clean
up so we only pass descriptors around.
Cc: Philipp Zabel <philipp.zabel@gmail.com> # HX4700/Magician maintainer
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we augmented the regulator core to accept a GPIO descriptor instead
of a GPIO number, we can augment the fixed GPIO regulator to look up
and pass that descriptor directly from device tree or board GPIO
descriptor look up tables.
Some boards just auto-enumerate their fixed regulator platform devices
and I have assumed they get names like "fixed-regulator.0" but it's
pretty hard to guess this. I need some testing from board maintainers to
be sure. Other boards are straight forward, using just plain
"fixed-regulator" (ID -1) or "fixed-regulator.1" hammering down the
device ID.
The OMAP didn't have proper label names on its GPIO chips so I have fixed
this with a separate patch to the GPIO tree, see
commit 088413bc0b
"gpio: omap: Give unique labels to each GPIO bank/chip"
It seems the da9055 and da9211 has never got around to actually passing
any enable gpio into its platform data (not the in-tree code anyway) so we
can just decide to simply pass a descriptor instead.
The fixed GPIO-controlled regulator in mach-pxa/ezx.c was confusingly named
"*_dummy_supply_device" while it is a very real device backed by a GPIO
line. There is nothing dummy about it at all, so I renamed it with the
infix *_regulator_* as part of this patch set.
For the patch hunk hitting arch/blackfin I would say I do not expect
testing, review or ACKs anymore so if it works, it works.
The hunk hitting the x86 BCM43xx driver is especially tricky as the number
comes out of SFI which is a mystery to me. I definately need someone to
look at this. (Hi Andy.)
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Check the x86 BCM stuff
Cc: Alexander Shiyan <shc_work@mail.ru> # i.MX boards user
Cc: Haojian Zhuang <haojian.zhuang@gmail.com> # MMP2 maintainer
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> # OMAP1 maintainer
Cc: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> # EM-X270 maintainer
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # EZX maintainer
Cc: Philipp Zabel <philipp.zabel@gmail.com> # Magician maintainer
Cc: Daniel Mack <zonque@gmail.com> # Raumfeld maintainer
Cc: Marc Zyngier <marc.zyngier@arm.com> # Zeus maintainer
Cc: Geert Uytterhoeven <geert+renesas@glider.be> # SuperH pinctrl/GPIO maintainer
Cc: Russell King <rmk+kernel@armlinux.org.uk> # SA1100
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The change to descriptors in 0369e02b75 "regulator: s2mps11: Pass
descriptor instead of GPIO number" has broken the boot on Odroid XU3
according to kernelci so let's revert that for now. We get a NULL
pointer defererence in:
[ 2.467929] [] (validate_desc) from [] (gpiod_set_value_cansleep+0x14/0x30)
[ 2.476591] [] (gpiod_set_value_cansleep) from [] (_regulator_do_enable+0x2f8/0x370)
[ 2.486032] [] (_regulator_do_enable) from [] (regulator_register+0xc54/0x1280)
[ 2.495045] [] (regulator_register) from [] (devm_regulator_register+0x40/0x7c)
[ 2.504057] [] (devm_regulator_register) from [] (s2mps11_pmic_probe+0x1c0/0x444)
[ 2.513243] [] (s2mps11_pmic_probe) from [] (platform_drv_probe+0x6c/0xa4)
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for SAW controlled regulators.
The regulators defined as SAW controlled in the device tree
will be controlled through special CPU registers instead of direct
SPMI accesses.
This is required especially for CPU supply regulators to synchronize
with clock scaling and for Automatic Voltage Switching.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node for the
regulator.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node for the
regulator.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We now pass a GPIO descriptor to the core instead of a global
GPIO number, if this descriptor is NULL the GPIO line is not
used. Just delete the assignment of an invalid GPIO line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up with the standard devm_gpiod_get_optional()
call.
All users of this regulator use device tree so the transition is
pretty smooth.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.
This driver has supported passing a LDO enable GPIO for years,
yet this facility has never been put to use in the upstream kernel.
If someone desires to put in place GPIO control for the LDOs,
this can be done by adding a GPIO descriptor table in the MFD
nexus in drivers/mfd/lp8788.c for the LDO device when spawning the
MFD children, or using a board file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_optional() call.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If is_enabled() is not defined, regulator core will assume
this regulator is already enabled, then it can NOT be really
enabled after disabled.
Based on Li Jun's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add enable/disable support for switch regulator on pfuze100.
Based on Robin Gong's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Uncoupled regulators should be a special case of coupled regulators, so
they should share a common voltage setting path. When enabling,
disabling or setting voltage of a coupled regulator, all coupled
regulators should be locked. Regulator's supplies should be locked, when
setting voltage of a single regulator. Enabling a coupled regulator or
setting its voltage should not be possible if some of its coupled
regulators, has not been registered.
Add function for locking coupled regulators and supplies. Extract
a new function regulator_set_voltage_rdev() from
regulator_set_voltage_unlocked(), which is called when setting
voltage of a single regulator.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Introduce new function regulator_balance_voltage(), which
keeps max_spread constraint fulfilled between a group of coupled
regulators. It should be called if a regulator changes its
voltage or after disabling or enabling. Disabled regulators should
follow changes of the enabled ones, but their consumers' demands
shouldn't be taken into account while calculating voltage of other
coupled regulators.
Find voltages, which are closest to suiting all the consumers' demands,
while fulfilling max_spread constraint, keeping the following rules:
- if one regulator is about to rise its voltage, rise others
voltages in order to keep the max_spread
- if a regulator, which has caused rising other regulators, is
lowered, lower other regulators if possible
- if one regulator is about to lower its voltage, but it hasn't caused
rising other regulators, don't change its voltage if it breaks the
max_spread
Change regulators' voltages step by step, keeping max_spread constraint
fulfilled all the time. Function regulator_get_optimal_voltage()
should find the best possible change for the regulator, which doesn't
break max_spread constraint. In function regulator_balance_voltage()
optimize number of steps by finding highest voltage difference on
each iteration.
If a regulator, which is about to change its voltage, is not coupled,
method regulator_get_optimal_voltage() should simply return the lowest
voltage fulfilling consumers' demands.
Coupling should be checked only if the system is in PM_SUSPEND_ON state.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
two devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Fill coupling descriptor with data obtained from DTS using previously
defined of_functions. Fail to register a regulator, if some data
inconsistency occurs. If some coupled regulators are not yet registered,
don't fail to register, but try to resolve them in late init call.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Odroid XU3/4 and other Exynos5422 based boards there is a case, that
different devices on the board are supplied by different regulators
with non-fixed voltages. If one of these devices temporarily requires
higher voltage, there might occur a situation that the spread between
devices' voltages is so high, that there is a risk of changing
'high' and 'low' states on the interconnection between devices powered
by those regulators.
Add new structure "coupling_desc" to regulator_dev, which contains
pointers to all coupled regulators including the owner of the structure,
number of coupled regulators and counter of currently resolved
regulators.
Add of_functions to parse all data needed in regulator coupling.
Provide method to check DTS data consistency. Check if each coupled
regulator's max_spread is equal and if their lists of regulators match.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting voltage, enabling/disabling regulators requires operations on
all regulators related with the regulator being changed. Therefore,
all of them should be locked for the whole operation. With the current
locking implementation, adding additional dependency (regulators
coupling) causes deadlocks in some cases.
Introduce a possibility to attempt to lock a mutex multiple times
by the same task without waiting on a mutex. This should handle all
reasonable coupling-supplying combinations, especially when two coupled
regulators share common supplies. The only situation that should be
forbidden is simultaneous coupling and supplying between a pair of
regulators.
The idea is based on clk core.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up with the standard devm_gpiod_get_optional()
call.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up from the device tree configuration node.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_optional() call.
We have augmented the GPIO core to look up the regulator special
GPIO "wlf,ldoena" in commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.
Fixes: ee999fb3f1 ("mfd: max8998: Add support for Device Tree")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for configuring the machine constraints
valid_modes_mask element based on a list of allowed modes
specified via a device tree property.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulators attached via RPMh on Qualcomm sdm845 apparently are
write-only. Specifically you can send a request for a certain voltage
but you can't read back to see what voltage you've requested. What
this means is that at bootup we have absolutely no idea what voltage
we could be at.
As discussed in the patches to try to support the RPMh regulators [1],
the fact that regulators are write-only means that its driver's
get_voltage_sel() should return an error code if it's called before
any calls to set_voltage_sel(). This causes problems in
machine_constraints_voltage() when trying to apply the constraints.
A proposed fix was to come up with an error code that could be
returned by get_voltage_sel() which would cause the regulator
framework to simply try setting the voltage with the current
constraints.
In this patch I propose the error code -ENOTRECOVERABLE. In errno.h
this error is described as "State not recoverable". Though the error
code was originally intended "for robust mutexes", the description of
the error code seems to apply here because we can't read the state of
the regulator. Also note that the only existing user of this error
code in the regulator framework is tps65090-regulator.c which returns
this error code from the enable() call (not get_voltage() or
get_voltage_sel()), so there should be no existing regulators that
might accidentally get the new behavior. (Side note is that tps65090
seems to interpret this error code to mean an error that you can't
recover from rather than some data that can't be recovered).
[1] https://patchwork.kernel.org/patch/10340897/
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SY8106A is an I2C attached single output regulator made by Silergy Corp,
which is used on several Allwinner H3/H5 SBCs to control the power
supply of the ARM cores.
Add a driver for it.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Change commit message, remove enable/disable code, add default
ramp_delay, add comment for go bit, add code for fixed mode voltage]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If device tree is not enabled, of_find_regulator_by_node() should have
a dummy function since the function call is still there.
This is to fix build error after CONFIG_NO_AUTO_INLINE is introduced.
If this option is enabled, GCC will not auto-inline functions that are
not explicitly marked as inline.
In this case (no CONFIG_OF), the copmiler will report error in function
regulator_dev_lookup().
W/O NO_AUTO_INLINE, function of_get_regulator() is auto-inlined and then
the call to of_find_regulator_by_node() is optimized out since
of_get_regulator() always return NULL.
W/ NO_AUTO_INLINE, the return value of of_get_regulator() is a variable
so the call to of_find_regulator_by_node() cannot be optimized out. So
we need a stub of_find_regulator_by_node().
static struct regulator_dev *regulator_dev_lookup(struct device *dev,
const char *supply)
{
struct regulator_dev *r = NULL;
struct device_node *node;
struct regulator_map *map;
const char *devname = NULL;
regulator_supply_alias(&dev, &supply);
/* first do a dt based lookup */
if (dev && dev->of_node) {
node = of_get_regulator(dev, supply);
if (node) {
r = of_find_regulator_by_node(node);
if (r)
return r;
...
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure the DVBxB bit 5, PGOOD mask, is set before changing voltage
on the buck converters. If the PGOOD mask bit is not set, the PMIC may
deassert the PGOOD signal during the voltage transition.
On systems that use the PGOOD signal as a power OK indication for the
board or SoC, which should be the case on correct designs, deasserting
the PGOOD signal will lead to system reset or shutdown, which is not
the expected behavior when changing PMIC buck converter voltage.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BD9571MWV PMIC supports backup mode, which keeps one or more DDR
rails powered while the main SoC is powered down.
Which DDR rails are to be kept powered is board-specific, and controlled
using the optional "rohm,ddr-backup-power" DT property. In the absence
of this property, backup mode is not available.
Backup mode can be enabled or disabled by the user using the standard
"wakeup" virtual file in sysfs, e.g. to enable:
echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup
When the PMIC is configured for backup mode, the role of the accessory
power switch changes from a power switch to a wake-up switch.
Two types of switches (or signals) can be used:
A. With a momentary power switch (or pulse signal), the PMIC is
configured for backup mode in the PMIC driver's suspend callback,
during system suspend.
Backup mode is enabled by default, as there is no further impact
during normal system operation.
B. With a toggle power switch (or level signal), the following steps
must be followed exactly:
1. Configure PMIC for backup mode,
2. Switch accessory power switch off, to prepare for system
suspend, which is a manual step not controlled by software,
3. Suspend system.
This mode is not yet supported by the driver.
As the switch type is board-specific, and cannot be determined
automatically, it is obtained from the presence of one of the
"rohm,rstbmode-*" properties in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like axp221, axp223, axp813 the axp803 is also supporting external
regulator to drive the OTG VBus through N_VBUSEN PMIC pin.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It seems that the loop index i is not being incremented and hence
potentially the while loop could spin forever. Fortunately with the
data being used this does not appear to happen at the moment.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In of_get_regulation_constraints() we were taking the result of
of_map_mode() (an unsigned int) and assigning it to an int. We were
then checking whether this value was -EINVAL. Some implementers of
of_map_mode() were returning -EINVAL (even though the return type of
their function needed to be unsigned int) because they needed to
signal an error back to of_get_regulation_constraints().
In general in the regulator framework the mode is always referred to
as an unsigned int. While we could fix this to be a signed int (the
highest value we store in there right now is 0x8), it's actually
pretty clean to just define the regulator mode 0x0 (the lack of any
bits set) as an invalid mode. Let's do that.
Fixes: 5e5e3a42c6 ("regulator: of: Add support for parsing initial and suspend modes")
Suggested-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This version is exists in the Samsung Galaxy Tab 10.1 which is based on the
Nvidia Tegra 2 board. The TPS658624 has the same SM2 voltage table as
TPS658623.
Signed-off-by: ryang <decatf@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
pfuze3000 datasheet(Rev.9.0) from:
https://www.nxp.com/docs/en/data-sheet/PF3000.pdf
updates sw1a's voltage range, the settings for 1.450V and 1.475V
are replaced with 1.8V and 3.3V:
5b'11110 1.450 (SW1B), 1.8 (SW1A/SW1AB)
5b'11111 1.475 (SW1B), 3.3 (SW1A/SW1AB)
the voltage calculation using steps is NOT available for sw1a now,
use voltage table instead.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Buck10 is a multi(dual) phase regulator. So as part of enabling it
turn on the LP87565_BUCK_CTRL_1_FPWM_MP_0_2 bit which forces it to
operate always in multiphase and forced-PWM operation mode.
This helps improve the transient voltage response while switching OPP.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The slew rate might need a +/- 15% margin as per the latest data manual:
http://www.ti.com/lit/ds/snvsb22/snvsb22.pdf
Hence take a conservative approach to program 85% of the original
hardware slew rate so that the software accommodates the margin
delay while voltage switching. Hence reduce the default ramp_delay
populated in the descriptors also by 15%.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the pm8998 and pmi8998 regulators as used in the MSM8998 platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
These seem to be leftovers from previous developments of the driver but
they never got removed. Dropping them still allows the code to compile
so everything must be fine.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the label is empty, it causes missing information and limits diagnostics
for instances such as 'cat /sys/kernel/debug/gpio'
Setting the label to the regulator supply_name will point to the device
using the gpio(s).
Signed-off-by: Nicholas Lowell <nlowell@lexmark.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Re-order error handling code and gotos to avoid leaks in error handling
paths.
Fixes: 9f946099fe ("regulator: gpio: fix parsing of gpio list")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This chip is found on Google Chromecast and Valve Steam Link devices.
It provides two DC regulators with I2C voltage control, separate GPIO
enable pins and one sleep mode pin.
This driver does not expose GPIO functionality, but supports voltage
control in 1.0-2.2V range, based on I2C register information given in
Chromecast kernel driver by Jisheng Zhang.
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
When resuming from idle with the new suspend mode configuration support
we go through the resume callbacks with a state of PM_SUSPEND_TO_IDLE
which we don't have regulator constraints for, causing an error:
dpm_run_callback(): regulator_resume_early+0x0/0x64 returns -22
PM: Device regulator.0 failed to resume early: error -22
Avoid this and similar errors by treating missing constraints as a noop.
See also commit 57a0dd1879 ("regulator: Fix suspend to idle"),
which fixed the suspend part.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This augments the DA9211 regulator driver to fetch its GPIO descriptors
directly from the device tree using the newly exported
devm_get_gpiod_from_child().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When setting up a fixed regulator on the DA9055, pass a descriptor
instead of a global GPIO number. This facility is not used in the
kernel so we can easily just say that this should be a descriptor
if/when put to use.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are currently passing a GPIO number from the global GPIO numberspace
into the regulator core for handling enable GPIOs. This is not good
since it ties into the global GPIO numberspace and uses gpio_to_desc()
to overcome this.
Start supporting passing an already initialized GPIO descriptor to the
core instead: leaf drivers pick their descriptors, associated directly
with the device node (or from ACPI or from a board descriptor table)
and use that directly without any roundtrip over the global GPIO
numberspace.
This looks messy since it adds a bunch of extra code in the core, but
at the end of the patch series we will delete the handling of the GPIO
number and only deal with descriptors so things end up neat.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If an unlikely failure in 'of_get_regulator_init_data()' occurs, we must
release the reference on the current 'child' node before returning.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
stm32_vrefbuf_enable() wrongly checks VRR bit: 0 stands for not ready,
1 for ready. It currently checks the opposite.
This makes enable routine to exit immediately without waiting for ready
flag.
Fixes: 0cdbf481e9 ("regulator: Add support for stm32-vrefbuf")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When suspending to idle with the new suspend mode configuration support
we go through the suspend callbacks with a state of PM_SUSPEND_TO_IDLE
which we don't have regulator constraints for, causing an error. Avoid
this and similar errors by treating missing constraints as a noop.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
3d67fe9507 (regulator: core: Refactor regulator_list_voltage()) missed
one user of regulator_list_voltage(), update for that.
Signed-off-by: Mark Brown <broonie@kernel.org>
Change _regulator_list_voltage() argument from regulator to
regulator_dev in order to provide better separation of core layers.
Allow calling _regulator_list_voltage() from functions, with
regulator_dev argument. This refactoring is needed in order to
implement setting voltage of coupled regulators.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
