Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> (in principle)
Signed-off-by: Eric Anholt <eric@anholt.net>
On Ironlake, there is an interrupt master control bit. With the bit
disabled before clearing IIR, we do not need to handle extra interrupt
in a loop. This patch removes the loop in Ironlake interrupt handler.
It fixed irq lost issue on some Ironlake platforms.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zou Nan hai <Nanhai.zou@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When we setup buffer for display plane, we'll check any pending
required GPU flush and possible make interruptible wait for flush
complete. But that wait would be most possibly to fail in case of
signals received for X process, which will then fail modeset process
and put display engine in unconsistent state. The result could be
blank screen or CPU hang, and DDX driver would always turn on outputs
DPMS after whatever modeset fails or not.
So this one creates new helper for setup display plane buffer, and
when needing flush using uninterruptible wait for that.
This one should fix bug like https://bugs.freedesktop.org/show_bug.cgi?id=24009.
Also fixing mode switch stress test on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
There exist multiple DDC buses for the SDVO cards with multiple outputs.
When we can't get the EDID by using the select DDC bus, we can try the other
possible DDC bus to see whether the EDID can be obtained.
https://bugs.freedesktop.org/show_bug.cgi?id=23842
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some SDVO cards based on conexant chip, we can't read the EDID if
we don't read the response after issuing SDVO DDC bus switch
command.
From the SDVO spec once when another I2C transaction is finished after
completing the I2C transaction of issuing the bus switch command, it
will be switched back to the SDVO internal state again. So we can't
initiate a new I2C transaction to read the response after issuing the
DDC bus switch command. Instead we should issue DDC bus switch command
and read the response in the same I2C transaction.
https://bugs.freedesktop.org/show_bug.cgi?id=23842https://bugs.freedesktop.org/show_bug.cgi?id=24458https://bugs.freedesktop.org/show_bug.cgi?id=24522https://bugs.freedesktop.org/show_bug.cgi?id=24282
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Eric Anholt <eric@anholt.net>
On some boxes the BIOS will report different child device arrays when
the system is booted with/without the dock. In such case the HDMI/DP
port can't be setup correctly. So revert two commits
(fc816655236cd9da162356e96e74c7cfb0834d92/
6e36595a21) that use the child device
parsed from VBT to setup HDMI/DP.
http://bugzilla.kernel.org/show_bug.cgi?id=14854http://bugzilla.kernel.org/show_bug.cgi?id=14860
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sean Young <sean@mess.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit cbda12d77e (drm/i915: implement
new pm ops for i915), among other things, removed the .suspend and
.resume pointers from the struct drm_driver object in i915_drv.c,
which broke resume without KMS on my MSI Wind U100.
Fix this by reverting that part of commit cbda12d77e.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: added comment explaining when .suspend/.resume matter]
Signed-off-by: Eric Anholt <eric@anholt.net>
Without this fix, some modes couldn't find appropriate clocks.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Matthew Garrett <mjg@redhat.com>
For any given clock we can use the find_pll to get the corresponding DPLL
setting. It is unnecessary to use the find_reduce_pll callback function
to calculate the DPLL parameter for LVDS downclock in order to get the same
divider factor(P) for the normal and downclock.
In theory when the LVDS downclock is supported by LVDS panel, we should get the
same DPLL divider factor(P) for the normal clock and reduced downclock.
If we get the diferent divider factor(P) for normal clock and reduced downclock,
it means that the found downclock is incorrect and should be discarded.
So we should use find_pll callback to calculate the DPLL parameter for the
LVDS reduced downclock as for the normal clock. Then we can do the cleanup
about find_reduced_pll.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As we removed TV hotplug, don't check its status ever.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/kms: Fix &&/|| confusion in drm_fb_helper_connector_parse_command_line()
drm/edid: Fix CVT width/height decode
drm/edid: Skip empty CVT codepoints
drm: remove address mask param for drm_pci_alloc()
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (23 commits)
drm/i915: remove full registers dump debug
drm/i915: Add DP dpll limit on ironlake and use existing DPLL search function
drm/i915: Select the correct BPC for LVDS on Ironlake
drm/i915: Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake
drm/i915: Enable/disable the dithering for LVDS based on VBT setting
drm/i915: Permit pinning whilst the device is 'suspended'
drm/i915: Hold struct mutex whilst pinning power context bo.
drm/i915: fix unused var
drm/i915: Storage class should be before const qualifier
drm/i915: remove render reclock support
drm/i915: Fix RC6 suspend/resume
drm/i915: execbuf2 support
drm/i915: Reload hangcheck timer too for Ironlake
drm/i915: only enable hotplug for detected outputs
drm/i915: Track whether cursor needs physical address in intel_device_info
drm/i915: Implement IS_* macros using static tables
drm/i915: Move PCI IDs into i915 driver
drm/i915: Update LVDS connector status when receiving ACPI LID event
drm/i915: Add MALATA PC-81005 to ACPI LID quirk list
drm/i915: implement new pm ops for i915
...
This one reverts 9e3a6d155e.
As reported by http://bugzilla.kernel.org/show_bug.cgi?id=14485,
this dump will cause hang problem on some machine. If something
really needs this kind of full registers dump, that could be done
within intel-gpu-tools.
Cc: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some clocks, the old Ironlake DPLL calculator wold give m/n/p
combinations that didn't match the spreadsheet of what HW validation
tests. Instead, use the G4X DPLL calculator, which does a better job
at it.
So we use the intel_g4x_find_best_pll to calculate the DPLL for CRT/HDMI/LVDS
on ironlake. At the same time to consider the dpll setting for display port, we
add the display port DPLL limit on ironlake, which will directly use the
function of intel_find_pll_ironlake_dp to get the corresponding dpll setting.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Select the correct BPC for LVDS on Ironlake. If it is 18-bit LVDS panel,
the BPC will be 6. When it is 24-bit LVDS panel, the BPC will 8.
At the same time the BPC will be 8 when the output device is CRT/HDMI/DP.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Enable/disable the dithering for LVDS based on VBT setting. On the 965/g4x
platform the dithering flag is defined in LVDS register. And on the ironlake
the dithering flag is defined in pipeconf register.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As pinning (allocating and binding GTT memory) does not actually invoke
GPU commands, it is safe, and indeed is attempted, during resumption
from suspension:
[drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Hugh found an error path where we were attempting to unref a bo without
holding the struct mutex:
[drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
------------[ cut here ]------------
WARNING: at drivers/gpu/drm/drm_gem.c:438 drm_gem_object_free+0x20/0x5e()
Hardware name: ESPRIMO Mobile V5505
Modules linked in: snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device
Pid: 3793, comm: s2ram Not tainted 2.6.33-rc2 #4
Call Trace:
[<7815298e>] warn_slowpath_common+0x59/0x6b
[<781529b3>] warn_slowpath_null+0x13/0x18
[<78317c1a>] ? drm_gem_object_free+0x20/0x5e
[<78317c1a>] drm_gem_object_free+0x20/0x5e
[<78317bfa>] ? drm_gem_object_free+0x0/0x5e
[<7829df11>] kref_put+0x38/0x45
[<7833a5f0>] intel_init_clock_gating+0x232/0x271
[<78317bfa>] ? drm_gem_object_free+0x0/0x5e
[<7832c307>] i915_restore_state+0x21a/0x2b3
[<7832379d>] i915_resume+0x3c/0xbb
[<78174fe5>] ? trace_hardirqs_on_caller+0xfc/0x123
[<7831c756>] ? drm_class_resume+0x0/0x3e
[<7831c78d>] drm_class_resume+0x37/0x3e
[<78351e0a>] legacy_resume+0x1e/0x51
[<78351ece>] device_resume+0x91/0xab
[<7831c756>] ? drm_class_resume+0x0/0x3e
[<78352226>] dpm_resume+0x58/0x10f
[<783522fb>] dpm_resume_end+0x1e/0x2c
[<78180f80>] suspend_devices_and_enter+0x61/0x84
[<78180ff8>] enter_state+0x55/0x83
[<7818091c>] state_store+0x94/0xaa
[<7829d09e>] kobj_attr_store+0x1e/0x23
[<782098e0>] sysfs_write_file+0x66/0x99
[<781cd2f0>] vfs_write+0x8a/0x108
[<781cd408>] sys_write+0x3c/0x63
[<78125c10>] sysenter_do_call+0x12/0x36
---[ end trace a343537f29950fda ]---
It is in fact slightly more insiduous that first appears since we are
attempting to not just free the object without the lock, but are trying
to do the whole bo manipulation without holding the lock.
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/i915_dma.c: In function 'i915_driver_load':
drivers/gpu/drm/i915/i915_dma.c:1114: warning: 'll_base' may be used uninitialized in this function
Partly this is because gcc isn't smart enough. But `ll_base' does get used
uninitialised in the DRM_DEBUG() call.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
This code generally fails to adjust the render clock, and when it does,
it conflicts with some other register settings and can cause problems.
So remove this code altogether. I'm reworking it now to do the right
thing, but the only bit it will share is the VBT check for whether
reclocking is supported, so I'm leaving that bit.
Reverts most of 652c393a33 ("add dynamic
clock frequency control"), though for many the regressions showed up
in the later 181a5336d6 ("Fix render
reclock availability detection").
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We restored RC6 twice on resume, even with modesetting off. Instead,
only restore it once and skip RC6 initialization entirely in non-KMS mode.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds a new execbuf ioctl, execbuf2, for use by clients that
want to control fence register allocation more finely. The buffer
passed in to the new ioctl includes a new relocation type to indicate
whether a given object needs a fence register assigned for the command
buffer in question.
Compatibility with the existing execbuf ioctl is implemented in terms
of the new code, preserving the assumption that fence registers are
required for pre-965 rendering commands.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: Remove pre-emptive clear_fence_reg()]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
[anholt: Removed dmesg spam]
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (35 commits)
drm/radeon/kms: add definitions for v4 power tables
drm/radeon/kms: never combine LVDS with another encoder
drm/radeon/kms: Check module arguments to be valid V2
drm/radeon/kms: Avoid crash when trying to cleanup uninitialized structure
drm/radeon/kms: add cvt mode if we only have lvds w/h and no edid (v4)
drm/radeon/kms: add 3DC compression support
drm/radeon/kms: allow rendering while no colorbuffer is set on r300
drm/radeon/kms: enable memory clock reading on legacy (V2)
drm/radeon/kms: prevent parallel AtomBIOS calls
drm/radeon/kms: set proper default tv standard
drm/radeon/kms: fix legacy rmx
drm/radeon/kms/atom: fill in proper defines for digital setup
drm/kms: silencing a false positive warning.
drm/mm: fix logic for selection of best fit block
drm/vmwgfx: Use TTM handles instead of SIDs as user-space surface handles.
drm/vmwgfx: Return -ERESTARTSYS when interrupted by a signal.
drm/vmwgfx: Fix unlocked ioctl and add proper access control
drm/radeon: fix build on 64-bit with some compilers.
drivers/gpu: Use kzalloc for allocating only one thing
DRM: Rename clamp variable
...
drm_ioctl is called with the Big Kernel Lock held,
which shows up very high in statistics on vfs_ioctl.
Moving the lock into the drm_ioctl function itself
makes sure we blame the right subsystem and it gets
us one step closer to eliminating the locked version
of fops->ioctl.
Since drm_ioctl does not require the lock itself,
we only need to hold it while calling the specific
handler. The 32 bit conversion handlers do not
interact with any other code, so they don't need
the BKL here either and can just call drm_ioctl.
As a bonus, this cleans up all the other users
of drm_ioctl which now no longer have to find
the inode or call lock_kernel.
[airlied: squashed the non-driver bits
of the second patch in here, this provides
the flag for drivers to use to select unlocked
ioctls - but doesn't modify any drivers].
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.sourceforge.net
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure hangcheck timer won't beat us unexpectedly on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch changes around our hotplug enable code a bit to only enable
it for ports we actually detect and initialize. This prevents problems
with stuck or spurious interrupts on outputs that aren't actually wired
up, and is generally more correct.
Fixes FDO bug #23183.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of using the IS_I9XX etc macros that expand to a ton of
comparisons, use new struct intel_device_info to capture the
capabilities of the different chipsets. The drm_i915_private struct
will be initialized to point to the device info that correspond to
the actual device and this way, testing for a specific capability is
just a matter of checking a bit field.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
The old include/drm/drm_pciids.h used to be generated from the libdrm
git repo. We don't use that anymore so just use a local list in the
driver like everybody else.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Dirk reports that nothing is displayed on LVDS when using ubuntu 9.1 after
close/reopen the LID. And I also reproduce this issue on another laptop.
After some tests and debug, it seems that it is related with that the
LVDS status is not updated in time in course of suspend/resume.
Now the LID state is used to check whether the LVDS is connected or
disconnected. And when the LID is closed, it means that the LVDS is
disconnected. When it is reopened, it means that the LVDS is connected.
At the same time on some distributions the LID event is also used to put
the system into suspend state. When the LID is closed, the system will enter
the suspend state. When the LID is reopened, the system will be resumed.
In such case when the LID is closed, user-space script will receive the LID
notification event and detect the LVDS as disconnected. Then the system will
enter the suspended state. When the LID is reopened, the system will be
resumed. As the LVDS status is not updated in course of resume, it will cause
that the LVDS connector is marked as unused and disabled. After the resume is
finished,user-space script will try to configure the display mode for LVDS.
But unfortunately as the LVDS status is not updated in time and it is still
marked as disconnected, the LVDS and its corresponding CRTC will be disabled
again in the function of drm_helper_disable_unused_functions after changing
mode for LVDS.
So we had better check and update the status of LVDS connector after receiving
the LID notication event. Then after the system is resumed from suspended
state, we can set the display mode for LVDS correctly.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reported-by: Dirk Hohndel <hohndel@infradead.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
The MALATA PC-81005 laptop always reports that the LID status is closed and we
can't use it reliabily for LVDS detection. So add this box into the quirk list.
https://bugs.freedesktop.org/show_bug.cgi?id=25523
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Review-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Hector <hector1987@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
One problem in i915 hibernate with current legacy pci pm ops is
that after we do freeze, we'll be forced to do resume once again,
which re-init some resources and do modesetting again, that is
unnecessary for hibernate. This patch trys to bypass that.
We can't resolve this within legacy pm framework, but can do it
easily with new pm ops. Suspend (S3) process has also been kept
without change.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Checking for the presence of a lid in order to validate whether or not
an LVDS display exists fails on some development platforms that implement
a lid device but allow the LVDS to be disabled. The VBT is correctly
updated, but Linux assumes that an LVDS is still present and lies to
userspace. Remove the lid check and trust the VBT.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
i915_gem_object_unbind had the ordering wrong. The other user,
i915_gem_object_put_fence_reg already has the correct ordering.
Results was usually corrupted pixmaps, especially garbled font glyphs
after a suspend/resume (because this evicts everything).
I'm still waiting for the feedback from the bug-reporters, but
because this obviously fixes a bug (at least for me) I'm already
submitting it.
Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=25406
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
CC: stable@kernel.org
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (189 commits)
drm/radeon/kms: fix warning about cur_placement being uninitialised.
drm/ttm: Print debug information on memory manager when eviction fails
drm: Add memory manager debug function
drm/radeon/kms: restore surface registers on resume.
drm/radeon/kms/r600/r700: fallback gracefully on ucode failure
drm/ttm: Initialize eviction placement in case the driver callback doesn't
drm/radeon/kms: cleanup structure and module if initialization fails
drm/radeon/kms: actualy set the eviction placements we choose
drm/radeon/kms: Fix NULL ptr dereference
drm/radeon/kms/avivo: add support for new pll selection algo
drm/radeon/kms/avivo: fix some bugs in the display bandwidth setup
drm/radeon/kms: fix return value from fence function.
drm/radeon: Remove tests for -ERESTART from the TTM code.
drm/ttm: Have the TTM code return -ERESTARTSYS instead of -ERESTART.
drm/radeon/kms: Convert radeon to new TTM validation API (V2)
drm/ttm: Rework validation & memory space allocation (V3)
drm: Add search/get functions to get a block in a specific range
drm/radeon/kms: fix avivo tiling regression since radeon object rework
drm/i915: Remove a debugging printk from hangcheck
drm/radeon/kms: make sure i2c id matches
...
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: Update version to 20091112.
ACPICA: Add additional module-level code support
ACPICA: Deploy new create integer interface where appropriate
ACPICA: New internal utility function to create Integer objects
ACPICA: Add repair for predefined methods that must return sorted lists
ACPICA: Fix possible fault if return Package objects contain NULL elements
ACPICA: Add post-order callback to acpi_walk_namespace
ACPICA: Change package length error message to an info message
ACPICA: Reduce severity of predefined repair messages, Warning to Info
ACPICA: Update version to 20091013
ACPICA: Fix possible memory leak for Scope ASL operator
ACPICA: Remove possibility of executing _REG methods twice
ACPICA: Add repair for bad _MAT buffers
ACPICA: Add repair for bad _BIF/_BIX packages
A residual bare printk survived the merger of the hang detector, remove
this debugging left-over.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Rather than restoring just a few clock gating registers on resume,
just reinitialize the whole thing.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
[anholt: Fixed up for RC6 support landed since the patch was written]
Signed-off-by: Eric Anholt <eric@anholt.net>
This merges the upstream Intel tree and fixes up numerous conflicts
due to patches merged into Linus tree later in -rc cycle.
Conflicts:
drivers/char/agp/intel-agp.c
drivers/gpu/drm/drm_dp_i2c_helper.c
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/i915_suspend.c
Both radeon and nouveau can re-use this code so move it up a level
so they can. However the hw interfaces for aux ch are different
enough that the code to translate from mode, address, bytes
to actual hw interfaces isn't generic, so move that code into the
Intel driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
IGD* isn't a useful name. Replace with the codenames, as sourced from
pci.ids.
Signed-off-by: Adam Jackson <ajax@redhat.com>
[anholt: Fixed up for merge with pineview/ironlake changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
These are handled by the error return being propagated to user-space and
do not any add any information to the original error, so are useless.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch brings the tree up to date with some fixes that were in a
more recent version of the page flipping patch you applied. It fixes
pre-965 flip support, removes a leftover hack that forced alignment,
and initializes the pipe & plane CRTC mappings.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the missing clonemask for display port on Ironlake.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
We were always looking for the PORT_IDPB entry.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This is a sync of a fix I made in the old UMS code. If the BIOS uses
the GMBUS and doesn't clear that setup, then our bit-banging I2C can
fail, leading to monitors not being detected.
Signed-off-by: Eric Anholt <eric@anholt.net>
In current vblank-wait implementation, if we turn off VGA output,
drm_wait_vblank will still wait on the disabled pipe until timeout,
because vblank on the pipe is assumed be enabled. This would cause
slow system response on some system such as moblin.
This patch resolve the issue by adding a drm helper function
drm_vblank_off which explicitly clear vblank_enabled[crtc], wake up
any waiting queue and save last vblank counter before turning off
crtc. It also slightly change drm_vblank_get to ensure that we will
will return immediately if trying to wait on a disabled pipe.
Signed-off-by: Li Peng <peng.li@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-applied for conflicts with overlay changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
Otherwise, I'd get stuck in a loop where (afaict) output scan would
trigger a TV interrupt, which would trigger a scan, etc. TV load
detection not being the fastest thing in the world, X would process
requests very slowly.
https://bugs.freedesktop.org/show_bug.cgi?id=24404
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Only update the render-clock on transition from busy to idle and vice
versa, or else we burn a significant percentage of the cpu just rewriting
the register -- not quite as power-friendly as intended ;-)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Assume that either the presence of an LVDS entry in the VBT or an ACPI
lid device indicates an LVDS device. ACPI lid alone is not sufficient.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add a GETPARAM request for checking if page flipping is supported.
Useful for the 2D driver to enable the flipping path.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Jakob Bornecrantz <jakob@vmware.com>
Acked-by: Thomas Hellström <thomas@shipmail.org>
Review-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse "Orange Smoothie" Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
PineView only has 2 ports for LVDS and CRT. Don't enable other
ports for it.
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We not only check the device type, but also check the addin_offset. If the
addin_offset is zero, it won't be initialized.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
[anholt: hand-applied due to conflicts]
Use the child device array to decide whether the given DP output should be
initialized. If the given DP port can't be found in child device array,
it is not present and won't be initialized.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Use the child device array to decide whether the given HDMI output should be
initialized. If the given HDMI port can't be found in child device array,
it is not present and won't be initialized.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
On some laptops there is no HDMI/DP. But the xrandr still reports
several disconnected HDMI/display ports. In such case the user will be
confused.
>DVI1 disconnected (normal left inverted right x axis y axis)
>DP1 disconnected (normal left inverted right x axis y axis)
>DVI2 disconnected (normal left inverted right x axis y axis)
>DP2 disconnected (normal left inverted right x axis y axis)
>DP3 disconnected (normal left inverted right x axis y axis)
This patch set is to use the child device parsed in VBT to decide whether
the HDMI/DP/LVDS/TV should be initialized.
Parse the child device from VBT.
The device class type is also added for LFP, TV, HDMI, DP output.
https://bugs.freedesktop.org/show_bug.cgi?id=22785
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Otherwise the chip may scribble over free memory.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This also extends the mutex to cover fbc disabling, which is safe.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
if no VBT is present, crt_ddc_bus will be left at 0, and cause us
to use that for the GPIO register offset. That's never a valid register
offset, so let the "undefined" value be 0 instead of -1.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
[anholt: clarified the commit message a bit]
In commit d2d9f2324, the guard for a valid video mode was removed. This
caused the regression:
kernel crash during kms graphic boot on Intel GM4500 platform
https://bugzilla.redhat.com/show_bug.cgi?id=540218
This patches changes the logic slightly not to rely on a coupled
variable, but to just check whether the video_modes is valid before
dereferencing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Zhenyu Wang <zhenyu.z.wang@intel.com>
[ickle: Actually reference the correct bug report]
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When switching to interruptible sleeps in the overlay code, I've
forgotten to recover from interruptions at one site. This
resulted in the overlay still running when it should have been
switched off. This in turn caused a hang on resume because it
tried to disable the (not-running) overlay in preparation for the
resume modeset.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=24980
Tested-by: maximlevitsky@gmail.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
I've suspected some bug there wrt to suspend, but that was not
the case. Clean up the code anyway.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
HW guys have an evaluation about the impact about EOS, and say the impact
is quite small, so they have removed EOS detection support. This patch
removes EOS feature.
revert commit 0430296558
directly reverting it gives a hunk error, so please use this one.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
[anholt: fixed up commit message for update that the feature's really gone]
20ms delay is quite big and the routine isn't called in atomic context.
better use msleep to let other tasks run. This can reduce cpu time used
by Xorg, so potentially boost boot.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In failure path, make sure encoder is cleaned up, otherwise there
is a kernel oops.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In disable sequence, all output ports on PCH have to be disabled
before PCH transcoder, but LVDS port was left always enabled. This
one fixes that by disable LVDS port properly during pipe disable
process, and resolved stability issue seen on Ironlake. Also move
panel fitting disable time just after pipe disable to align with
the spec.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The DPLL calculation logic for 9xx platform is changed in:
commit 652c393a33
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Mon Aug 17 13:31:43 2009 -0700
drm/i915: add dynamic clock frequency control
Maybe we will get the different M/N/P combination with that by using the
previous dpll calculation logic.
So restore the DPLL calculation logic for 9xx platform.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Enumerate the LVDS panel timing info entry list in VBT to check whether
the LVDS downclock is found. If found, the downclock is also used to switch
dynamically between low and high frequency for LVDS.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
If more than one mode with the same resolution defined in EDID has different
refresh rate, it is thought that the downclock is found for LVDS.
We will program the different FPx0/1 register so that we can select dynamically
between the low and high frequency.
On the g4x platform we will use the CxSR feature to switch the different
refresh rate if the LVDS downclock feature is supported.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
For CRT hotplug detect status, we have four test results as blue
channel only, green channel only, both blue and green channel, and
no channel attached. Origin code only marks both blue and green channel
case as connected, but ignore other possible connected states. This one
trys to detect CRT by checking no channel attached case instead.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Execbufs involve quite a bit of payload, to the extent that cache misses
show up in the profiles here, and a suspicion that some of those cachelines
may get evicted and then reloaded in the subsequent copy.
This is still abstracted like drm_calloc_large since we want to check for
size overflow, and because we want to choose between kmalloc and vmalloc
on the fly. cairo's interface for malloc-with-calloc's-args was used as
the model.
Signed-off-by: Eric Anholt <eric@anholt.net>
The existing interface only has a pre-order callback. This change
adds an additional parameter for a post-order callback which will
be more useful for bus scans. ACPICA BZ 779.
Also update the external calls to acpi_walk_namespace.
http://www.acpica.org/bugzilla/show_bug.cgi?id=779
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a new flag to the drmWaitVblank ioctl, which asks the drm
to return immediately and notify userspace when the specified vblank sequence
happens by sending an event back on the drm fd.
The event mechanism works with the other flags supported by the ioctls,
specifically, the vblank sequence can be specified relatively or absolutely,
and works for primary and seconday crtc.
The signal field of the vblank request is used to provide user data,
which will be sent back to user space in the vblank event.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add more display registers save/restore to fix unstable issues
during S4 testing on Ironlake. And DPLL_B_MD should not be restored
on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The master irq control in DE must be disabled before irq handling,
and enable after the process. This fixes the irq stall issue on
Ironlake.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zou, Nanhai <nanhai.zou@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Somehow the case for G33 got dropped while porting from ums code.
This made a 400MHz chip into a 133MHz one which resulted in the
unnecessary enabling of double wide pipe mode which in turn
screwed up the overlay code.
Nothing else (than the overlay code) seems to be affected.
This fixes fdo.org bug #24835
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the support of ACPI opregion on Ironlake so that the backlight
brightness can be adjusted by using ACPI interface
>/sys/class/backlight/acpi_video0/brightness
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Zhao Yakui <yakui.zhao@intel.com>
[zhenyuw: cleanups, fix typo for checking GSE irq and convert to
current irq handling logic.]
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Create a /debug/dri/%d/i915_wedged file to display the current wedged
status, and to enable setting that value. On an i965, this will also
trigger a GPU reset.
Useful in order to attempt to recover from some error conditions that
are not currently caught by the automatic hang detection code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Our work is serialised so allocating per-cpu workqueues is overkill and
a waste of resources.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Replace the DRM_DEBUG with DRM_DEBUG_KMS in output device code.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Replace the DRM_DEBUG with DRM_DEBUG_DRIVER in generic i915 driver.
Then the debug info can be obtained by adding the boot option of
"drm.debug=0x02".
At the same time the debug info in increase/decrease clock is also
printed by using DRM_DEBUG_DRIVER instead of DRM_DEBUG_KMS.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
I've simply overlooked one case in the conversion to interruptible
sleeps. Rectify this.
Also delete a leftover debug printk.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
At least for the common case of userspace ioctls. When doing a
modeset operation, the wait is still uninterruptible. But considering
that failing to turn off the overlay when switching off the crtc it's
running on hangs the chip, it doesn't complicate matters _very_
much. There's just an unkillable X in addition to a black screen.
BUG() about it and explain in the code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
As long as the gpu can keep up, neither the cpu (waiting for gpu)
nore the gpu (waiting for vblank to do an overlay flip) stalls.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Now that the cache flushing of the memory based overlay regs works,
we can safely switch off the overlay. Beforehand it was only disabled
(like in userspace).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
This implements intel overlay support for kms via a device-specific
ioctl. Thomas Hellstrom brought up the idea of a general ioctl (on
dri-devel). We've reached the conclusion that such an infrastructure
only makes sense when multiple kms overlay implementations exists,
which atm don't (and it doesn't look like this is gonna change).
Open issues:
- Runs in sync with the gpu, i.e. unnecessary waiting. I've decided
to wait on this because the hw tends to hang when changing something
in this area. I left some dummy functions as infrastructure.
- polyphase filtering uses a static table.
- uses uninterruptible sleeps. Unfortunately the alternatives may
unnecessarily wedged the hw if/when we timeout too early (and
userspace only overloaded the batch buffers with stuff worth a few
secs of gpu time).
Changes since v1:
- fix off-by-one misconception on my side. This fixes fullscreen
playback.
Changes since v2:
- add underrun detection as spec'ed for i965.
- flush caches properly, fixing visual corruptions.
Changes since v4:
- fix up cache flushing of overlay memory regs.
- killed require_pipe_a logic - it hangs the chip.
Tested-By: diego.abelenda@gmail.com (on a 865G)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[anholt: Resolved against the MADVISE ioctl going in before this one]
Signed-off-by: Eric Anholt <eric@anholt.net>
It is identical to I85X. Use that one instead.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[anholt: fix conflicts against the display function pointer stuff]
Signed-off-by: Eric Anholt <eric@anholt.net>
This just waits until the hw passed the current ring position with
cmd execution. This slightly changes the existing i915_wait_request
function to make uninterruptible waiting possible - no point in
returning to userspace while mucking around with the overlay, that
piece of hw is just too fragile.
Also replace a magic 0 with the symbolic constant (and kill the then
superflous comment) while I was looking at the code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Render standy allows the GPU to power down the render unit when idle.
In order for this to work, it needs a page of graphics memory to save
state. This patch allocates that page and enables the feature on
supported chipsets.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This brings some hardware workaround for HDMI port on PCH (Ibex Peak),
which fixes unstable issues like during rotation.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the ideal error range can't be reached, this will safely use
a most closed one. Clean up some dumb codes in DPLL function too.
This fixes DPLL clock issue against one monitor at 1680x1050@60hz.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Miles Lane reported the following error:
2 locks held by cat/4179:
#0: (&p->lock){+.+.+.}, at: [<c10a3884>] seq_read+0x25/0x315
#1: (&dev_priv->mm.active_list_lock){+.+...}, at: [<c119a854>]
i915_batchbuffer_info+0x2b/0x124
Pid: 4179, comm: cat Not tainted 2.6.32-rc5-git1 #2
Call Trace:
[<c104874f>] ? __debug_show_held_locks+0x1e/0x20
[<c1023fb0>] __might_sleep+0xf0/0xf7
[<c101c393>] kmap+0x17/0x58
[<c119a8d6>] i915_batchbuffer_info+0xad/0x124
[<c10a39bf>] seq_read+0x160/0x315
[<c108fb8c>] ? rw_verify_area+0x98/0xbb
[<c10a385f>] ? seq_read+0x0/0x315
[<c1090331>] vfs_read+0x75/0xa9
[<c10903f9>] sys_read+0x3b/0x5d
[<c1002a8f>] sysenter_do_call+0x12/0x36
The fix is relatively simple, use the atomic variants of kmap() that
avoid the potential sleep.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ironlake suspend/resume support
drm/i915: kill warning in intel_find_pll_g4x_dp
drm/i915: update watermarks before enabling PLLs
drm/i915: add FIFO watermark support for G4x
drm/i915: quiet DP i2c init
drm/i915: fix panel fitting filter coefficient select for Ironlake
drm/i915: fix to setup display reference clock control on Ironlake
drm/i915: Install a fence register for fbc on g4x
drm/i915: save/restore BLC histogram control reg across suspend/resume
drm/i915: Fix FDI M/N setting according with correct color depth
drm/i915: disable powersave feature for Ironlake currently
drm/i915: Fix render reclock availability detection.
drm/i915: Save and restore the GM45 FBC regs on suspend and resume.
drm/i915: Set the LVDS_BORDER when using LVDS scaling mode
drm/i915: disable FBC for Pineview, fixing a boot hang.
In commit c1c7af6089 ("drm/i915: force
mode set at lid open time") the intel graphics driver was taught to
restore the LVDS mode on lid open.
That caused problems with interaction with the suspend/resume code,
which commonly runs at the same time (suspend is often caused by the lid
close event, while lid open is commonly a resume event), which was
worked around with in commit 06891e27a9
("drm/i915: fix suspend/resume breakage in lid notifier").
However, in the meantime the lid event code had also grown a user event
notifier (commit 06324194ee: "drm/i915:
generate a KMS uevent at lid open/close time"), and now _that_ causes
problems with suspend/resume and some versions of Xorg reacting to those
uevents by setting the mode.
So this effectively reverts that commit 06324194ee, and makes the lid
open protection logic against suspend/resume more explicit. This fixes
at least one laptop. See
http://bugzilla.kernel.org/show_bug.cgi?id=14484
for more details.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a new flag to the drmWaitVblank ioctl, which asks the drm
to return immediately and notify userspace when the specified vblank sequence
happens by sending an event back on the drm fd.
The event mechanism works with the other flags supported by the ioctls,
specifically, the vblank sequence can be specified relatively or absolutely,
and works for primary and seconday crtc.
The signal field of the vblank request is used to provide user data,
which will be sent back to user space in the vblank event.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds registers save/restore for Ironlake to make suspend work.
Signed-off-by: Guo, Chaohong <chaohong.guo@intel.com>
[zhenyuw: some code re-orgnization, and add more save/restore for
FDI link and transcoder registers, also fix palette register for Ironlake]
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When coming back from DPMS or turning on a display, make sure we have
the watermarks set up before turning on the display plane, otherwise we
may get underruns.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Turns out G4x needs to have sensible watermarks set, especially for
self-refresh enabled modes. Add support for it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Must set filter selection as hardcoded coefficients for medium 3x3
filtering, which matches vbios setting for Ironlake.
This fixes display corrupt issue on HP arrandale with new vbios.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For new stepping of PCH, the display reference clock
is fully under driver's control. This one trys to setup
all needed reference clock for different outputs. Older
stepping of PCH chipset should be ignoring this.
This fixes output failure issue on newer PCH which requires
driver to take control of reference clock enabling.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
To enable framebuffer compression on a g4x, we not only need the buffer
to tiled (X only), we also need to hold a fence register for the buffer.
Currently we only install a fence register for pre-i965s when setting up
the scanout buffer. Rather than adding some convoluted logic to
g4x_enable_fbc() to acquire a fence register, and perhaps to
g4x_disable_fbc() to release it again, we can extend the acquisition
during setup to all chipsets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Turns out some machines, like the ThinkPad X40 don't come back if you
don't save/restore this register.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
FDI M/N calculation hasn't taken the current pipe color depth into account,
but always set as 24bpp. This one checks current pipe color depth setting,
and change FDI M/N calculation a little to use bits_per_pixel first, then
convert to bytes_per_pixel later.
This fixes display corrupt issue on Arrandle LVDS with 1600x900 panel
in 18bpp dual-channel mode.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Until we figure out the right setting for powersave features on
Ironlake, disable it for now. Also disable watermark update,
which has new registers for it on Ironlake too.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Resolved against the Pineview FBC changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
If the device didn't support EDP, we would bail out too soon.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
[anholt: Pulled this patch out of the patch for adding quirks to
enable reclocking.]
Signed-off-by: Eric Anholt <eric@anholt.net>
This hasn't fixed the regressions we were testing against, but clearly
should be required.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
According to the spec the LVDS_BORDER_ENABLE bit decides whether the border
data should be included in the active display and data sent to the panel.
Border should be used when in VGA centered (un-scaled) mode or when scaling
a 4:3 source image to a wide screen panel (typical 16:9).
So when the LVDS scaling is used, decide whether the LVDS_BORDER should be
enabled or not according to the current scaling mode.
At the same time fix the typo error in LVDS center scaling mode.
https://bugs.freedesktop.org/show_bug.cgi?id=23789
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
tested-by: Zhao Jian <jian.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Pineview doesn't have this FBC mechanism, so this code doesn't apply.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Initialize HDMI outputs as HDMI connectors, not DVI.
drm/i915: Multiply the refresh by 1000 in TV mode validatiion
drm/i915: Enable irq to trace batch buffer completion.
drm/i915: batch submit seqno off-by-one.
drm/i915: Record device minor rather than pointer in TRACE_EVENT
drm/i915: Don't call intel_update_fbc from intel_crtc_cursor_set
conflict in radeon since new init path merged with vga arb code.
Conflicts:
drivers/gpu/drm/radeon/radeon.h
drivers/gpu/drm/radeon/radeon_asic.h
drivers/gpu/drm/radeon/radeon_device.c
The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.
this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.
Tested on r100/r600/i945.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Even if the physical output connector is DVI, calling it HDMI
tells the user that there's HDMI audio signaling support.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As of 559ee21d26 the actual refresh rate
is returned by the function of drm_mode_vrefresh, so multiply the refresh
rate by 1000 in TV mode validation.
At the same time the error is expanded from 10 to 1000.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (25 commits)
drm/radeon/kms: Convert R520 to new init path and associated cleanup
drm/radeon/kms: Convert RV515 to new init path and associated cleanup
drm: fix radeon DRM warnings when !CONFIG_DEBUG_FS
drm: fix drm_fb_helper warning when !CONFIG_MAGIC_SYSRQ
drm/r600: fix memory leak introduced with 64k malloc avoidance fix.
drm/kms: make fb helper work for all drivers.
drm/radeon/r600: fix offset handling in CS parser
drm/radeon/kms/r600: fix forcing pci mode on agp cards
drm/radeon/kms: fix for the extra pages copying.
drm/radeon/kms/r600: add support for vline relocs
drm/radeon/kms: fix some bugs in vline reloc
drm/radeon/kms/r600: clamp vram to aperture size
drm/kms: protect against fb helper not being created.
drm/r600: get values from the passed in IB not the copy.
drm: create gitignore file for radeon
drm/radeon/kms: remove unneeded master create/destroy functions.
drm/kms: start adding command line interface using fb.
fb: change rules for global rules match.
drm/radeon/kms: don't require up to 64k allocations. (v2)
drm/radeon/kms: enable dac load detection by default.
...
Trivial conflicts in drivers/gpu/drm/radeon/radeon_asic.h due to adding
'->vga_set_state' function pointers.
If we trigger a tracepoint for batch buffer submission, it is a reasonable
assumption that we wish to also trace the batch buffer completion. So in
order to capture the completion events, we need to enable irqs... However,
we cannot rely on the completion event to disable the irq later, so we
defer the irq disable to the retire request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We increment the seqno number between submitting the batch buffer and
the flush/interrupt that demarcates its end, so the tracepoint needs to
reference the incremented value to match the completion event.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 74dff282 exposed this unnecessary call by causing a change in
the failure path on i965 where framebuffer compression will be turned
on and off on every cursor update. If you don't have the xf86-video-intel
fix to avoid the blinking cursor effect, this is very slow.
Symptoms were a far more noticeable cursor blink with every cursor image
change combined with severe slowdown for animated cursors.
Signed-off-by: Brian Rogers <brian@xyzw.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
[note this requires an fb patch posted to linux-fbdev-devel already]
This uses the normal video= command line option to control the kms
output setup at boot time. It is used to override the autodetection
done by kms.
video= normally takes a framebuffer as the first parameter, in kms
it will take a connector name, DVI-I-1, or LVDS-1 etc. If no output
connector is specified the mode string will apply to all connectors.
The mode specification used will match down the probed modes, and if
no mode is found it will add a CVT mode that matches.
video=1024x768 - all connectors match a 1024x768 mode or add a CVT on
video=VGA-1:1024x768, VGA-1 connector gets mode only.
The same strings as used in current fb modedb.c are used, except I've
added three more letters, e, D, d, e = enable, D = enable Digital,
d = disable, which allow a connector to be forced into a certain state.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (57 commits)
drm/i915: Handle ERESTARTSYS during page fault
drm/i915: Warn before mmaping a purgeable buffer.
drm/i915: Track purged state.
drm/i915: Remove eviction debug spam
drm/i915: Immediately discard any backing storage for uneeded objects
drm/i915: Do not mis-classify clean objects as purgeable
drm/i915: Whitespace correction for madv
drm/i915: BUG_ON page refleak during unbind
drm/i915: Search harder for a reusable object
drm/i915: Clean up evict from list.
drm/i915: Add tracepoints
drm/i915: framebuffer compression for GM45+
drm/i915: split display functions by chip type
drm/i915: Skip the sanity checks if the current relocation is valid
drm/i915: Check that the relocation points to within the target
drm/i915: correct FBC update when pipe base update occurs
drm/i915: blacklist Acer AspireOne lid status
ACPI: make ACPI button funcs no-ops if not built in
drm/i915: prevent FIFO calculation overflows on 32 bits with high dotclocks
drm/i915: intel_display.c handle latency variable efficiently
...
Fix up trivial conflicts in drivers/gpu/drm/i915/{i915_dma.c|i915_drv.h}