Remove clustered APIC mode. There's little point in the use of clustered APIC
mode, broadcasting is limited to within the cluster only, and chipsets have
bugs in this area as well. So default to physical APIC mode when the CPU
count is large, and default to logical APIC mode when the CPU count is 8 or
smaller.
(this patch only removes the use of genapic_cluster and cleans up the
resulting genapic.c file - removal of all remaining traces of clustered
mode will be done by another patch.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix a couple of inconsistencies/problems I found while reviewing the x86_64
genapic code (when I was chasing mysterious eth0 timeouts that would only
trigger if CPU_HOTPLUG is enabled):
- AMD systems defaulted to the slower flat-physical mode instead
of the flat-logical mode. The only restriction on AMD systems
is that they should not use clustered APIC mode.
- removed the CPU hotplug hacks, switching the default for small
systems back from phys-flat to logical-flat. The switching to logical
flat mode on small systems fixed sporadic ethernet driver timeouts i
was getting on a dual-core Athlon64 system:
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0c 0005 c07f media 80.
eth0: Tx queue start entry 32 dirty entry 28.
eth0: Tx descriptor 0 is 0008a04a. (queue head)
eth0: Tx descriptor 1 is 0008a04a.
eth0: Tx descriptor 2 is 0008a04a.
eth0: Tx descriptor 3 is 0008a04a.
eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
- The use of '<= 8' was a bug by itself (the valid APIC ids
for logical flat mode go from 0 to 7, not 0 to 8). The new logic
is to use logical flat mode on both AMD and Intel systems, and
to only switch to physical mode when logical mode cannot be used.
If CPU hotplug is racy wrt. APIC shutdown then CPU hotplug needs
fixing, not the whole IRQ system be made inconsistent and slowed
down.
- minor cleanups: simplified some code constructs
build & booted on a couple of AMD and Intel SMP systems.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Adds proper lines to help output of kconfig so people can find the module names.
Also fixed some broken leading spaces versus tabs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dave Jones <davej@redhat.com>
This patches fixes the silent data corruption problems being seen using the
GART iommu where 4kB of data where incorrect (seen mostly on Nvidia CK804
systems). This fix, to mark the memory regin the GART PTEs reside on as
uncacheable, also brings the code in line with the AGP specification.
Signed-off-by: Joachim Deguara <joachim.deguara@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[BRIDGE]: Unaligned access when comparing ethernet addresses
[SCTP]: Unmap v4mapped addresses during SCTP_BINDX_REM_ADDR operation.
[SCTP]: Fix assertion (!atomic_read(&sk->sk_rmem_alloc)) failed message
[NET]: Set a separate lockdep class for neighbour table's proxy_queue
[NET]: Fix UDP checksum issue in net poll mode.
[KEY]: Fix conversion between IPSEC_MODE_xxx and XFRM_MODE_xxx.
[NET]: Get rid of alloc_skb_from_cache
Since this was added originally for Xen, and Xen has recently (~2.6.18)
stopped using this function, we can safely get rid of it. Good timing
too since this function has started to bit rot.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
cache_k8_northbridges() is storing config values to incorrect locations
(in flush_words) and also its overflowing beyond the allocation, causing
slab verification failures.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While reviewing this code again I found a potential overflow of the bitmap.
The p4 oprofile can theoretically set bits beyond the reservation bitmap for
specific configurations. Avoid that by sizing the bitmaps properly.
Signed-off-by: Andi Kleen <ak@suse.de>
Due to an over aggressive optimizer gcc 4.2 cannot optimize away _proxy_pda
in all cases (counter intuitive, but true). This breaks loading of some
modules.
The earlier workaround to just export a dummy symbol didn't work unfortunately
because the module code ignores exports with 0 value.
Make it 1 instead.
Signed-off-by: Andi Kleen <ak@suse.de>
Provide a failsafe mechanism to avoid kernel spinning forever at
read_hpet_tsc during early kernel bootup.
This failsafe mechanism was originally introduced in commit
2f7a2a79c3, but looks like the hpet split
from time.c lost it again.
This reintroduces the failsafe mechanism
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:nvidia_bugs from .data between 'early_qrk' (at offset 0x8428) and 'enable_cpu_hotplug'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:via_bugs from .data between 'early_qrk' (at offset 0x8438) and 'enable_cpu_hotplug'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:ati_bugs from .data between 'early_qrk' (at offset 0x8448) and 'enable_cpu_hotplug'
The compiler is putting it into .data because the __initdata is in the wrong
place.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MSR reservation is per CPU and oprofile would only allocate them
on the CPU it was initialized on. Change this to handle all CPUs.
This also fixes a warning about unprotected use of smp_processor_id()
in preemptible kernels.
Signed-off-by: Andi Kleen <ak@suse.de>
This reverts commit 94985134b7 and
insteads removes the WARN_ON() that caused that commit in the first
place.
The problem is that we call disable_nonboot_cpus() in swsusp before
powering down the system in order to avoid triggering the WARN_ON()
in arch/x86_64/kernel/acpi/sleep.c:init_low_mapping() and this doesn't
work well on Thomas' system.
So instead, remove the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c:
init_low_mapping(), which triggers every time during the suspend to disk
in the platform mode, as the potential problem it is related to doesn't
seem to occur in practice.
[ I think we might want to disallow the case of multiple users of that
mm, or something. Normally, playing with the current process page
tables on the current CPU should be fine as long as we don't have
other threads using those tables at the same time..
Anyway, not pretty, but better than the warning or the lockup - Linus ]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ray Lee reported, that on an UP kernel with "noapic" command line option
set, the box locks hard during boot.
Adding some debug printks revealed, that the last action on the box
before stalling was "Send IPI" - a debug printk which was put into
smp_send_timer_broadcast_ipi().
It seems that send_IPI_mask(mask, LOCAL_TIMER_VECTOR) fails when
"noapic" is set on the command line on an UP kernel.
Aside of that it does not make much sense to trigger an interrupt
instead of calling the function directly on the CPU which gets the
PIT/HPET interrupt in case of broadcasting.
Reported-by: Ray Lee <ray-lk@madrabbit.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ray Lee <ray-lk@madrabbit.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Needed for any architecture that claims ARCH_APICTIMER_STOPS_ON_C3,
not just i386.
I'm hoping Thomas will clean this up a bit later..
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix atomicity of TIF update in flush_thread() for x86_64
Race :
parent process executing :
sys_ptrace()
(lock_kernel())
(ptrace_get_task_struct(pid))
arch_ptrace()
ptrace_detach()
ptrace_disable(child);
clear_singlestep(child);
clear_tsk_thread_flag(child, TIF_SINGLESTEP);
(which clears the TIF_SINGLESTEP flag atomically from a different
process)
(put_task_struct(child))
(unlock_kernel())
And at the same time, in the child process :
sys_execve()
do_execve()
search_binary_handler()
load_elf_binary()
flush_old_exec()
flush_thread()
doing a non-atomic thread flag update
Signed-off-by: Rebecca Schultz <rschultz@google.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
CONFIG_X86_P4_CLOCKMOD=y
arch/x86_64/kernel/built-in.o: In function `cpufreq_p4_verify':p4-clockmod.c:(.text.cpufreq_p4_verify+0x8): undefined reference to `cpufreq_frequency_table_verify'
arch/x86_64/kernel/built-in.o: In function `cpufreq_p4_cpu_exit':p4-clockmod.c:(.text.cpufreq_p4_cpu_exit+0x8): undefined reference to `cpufreq_frequency_table_put_attr'
arch/x86_64/kernel/built-in.o: In function `cpufreq_p4_cpu_init':p4-clockmod.c:(.text.cpufreq_p4_cpu_init+0x13b): undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Dave Jones <davej@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The symbol is not actually used, but the compiler unforunately generates
a (unused) reference to it. This can happen even in modules. So export it.
Signed-off-by: Andi Kleen <ak@suse.de>
Fix the following section mismatch warnings on x86_64:
(build using defconfig)
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:mtrr_bp_init from .text between 'identify_cpu' (at offset 0x65eb) and 'IRQ0x20_interrupt'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data: from .text between 'finish_e820_parsing' (at offset 0x7dc2) and 'early_panic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:e820_print_map from .text between 'finish_e820_parsing' (at offset 0x7de1) and 'early_panic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:num_processors from .text between 'acpi_unmap_lsapic' (at offset 0xc88f) and 'acpi_register_ioapic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:disabled_cpus from .text between 'MP_processor_info' (at offset 0x11f35) and 'mp_register_lapic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:num_processors from .text between 'MP_processor_info' (at offset 0x11f6e) and 'mp_register_lapic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:num_processors from .text between 'MP_processor_info' (at offset 0x11f93) and 'mp_register_lapic'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:fix_aperture from .text between 'gart_parse_options' (at offset 0x15517) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:fix_aperture from .text between 'gart_parse_options' (at offset 0x1552c) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_allowed from .text between 'gart_parse_options' (at offset 0x1553d) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_allowed from .text between 'gart_parse_options' (at offset 0x15552) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_allowed from .text between 'gart_parse_options' (at offset 0x15561) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_allowed from .text between 'gart_parse_options' (at offset 0x15577) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:fallback_aper_force from .text between 'gart_parse_options' (at offset 0x1558a) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:fallback_aper_order from .text between 'gart_parse_options' (at offset 0x155bf) and 'iommu_full'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:timer_over_8254 from .text between 'ati_bugs' (at offset 0x16344) and 'via_bugs'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:timer_over_8254 from .text between 'ati_bugs' (at offset 0x16356) and 'via_bugs'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_allowed from .text between 'via_bugs' (at offset 0x16380) and 'nvidia_bugs'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:iommu_aperture_disabled from .text between 'via_bugs' (at offset 0x16397) and 'nvidia_bugs'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:acpi_use_timer_override from .text between 'nvidia_bugs' (at offset 0x163a7) and 'arch_unregister_cpu'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:nvidia_hpet_check from .text between 'nvidia_bugs' (at offset 0x163b1) and 'arch_unregister_cpu'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data: from .text between 'nvidia_bugs' (at offset 0x163be) and 'arch_unregister_cpu'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data: from .text between 'nvidia_bugs' (at offset 0x163d1) and 'arch_unregister_cpu'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:acpi_skip_timer_override from .text between 'nvidia_bugs' (at offset 0x163e1) and 'arch_unregister_cpu'
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:quirk_intel_irqbalance from .text between 'intel_bugs' (at offset 0x1633c) and 'ati_bugs'
But adds:
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:get_mtrr_state from .text between 'mtrr_bp_init' (at offset 0xb887) and 'ipi_handler'
The warnings does not show up during a normal build due to kbuild
failing to check for section mismatch in vmlinux.
To see these warnings run:
scripts/mod/modpost arch/x86_64/kernel/built-in.o
kbuild will be fixed but the 'noise-level' had to be decresed first.
There remains a few section mismatch warnigns for x86_64 for areas where I did
not feel confident.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
x86_64 nvidia_bugs() broke when we bailed out on not finding the HPET.
However, the quirk works by checking for _not_ finding the HPET...
Delete the nvidia_hpet_detected flag and simply test for
not finding the HPET, which is simple to do now that
acpi_table_parse returns 1 on failure.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
check_tsc_sync_source() depends on being called with irqs disabled (it
checks whether the TSC is coherent across two specific CPUs). This is
incidentally true during bootup, but not during cpu hotplug __cpu_up().
This got found via smp_processor_id() debugging.
disable irqs explicitly and remove the unconditional enabling of
interrupts. Add touch_nmi_watchdog() to the cpu_online_map busy loop.
this bug is present both on i386 and on x86_64.
Reported-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resolves the issue found here:
http://bugme.osdl.org/show_bug.cgi?id=7426
The basic summary is:
Currently we register most of i386/x86_64 clocksources at module_init
time. Then we enable clocksource selection at late_initcall time. This
causes some problems for drivers that use gettimeofday for init
calibration routines (specifically the es1968 driver in this case),
where durring module_init, the only clocksource available is the low-res
jiffies clocksource. This may cause slight calibration errors, due to
the small sampling time used.
It should be noted that drivers that require fine grained time may not
function on architectures that do not have better then jiffies
resolution timekeeping (there are a few). However, this does not
discount the reasonable need for such fine-grained timekeeping at init
time.
Thus the solution here is to register clocksources earlier (ideally when
the hardware is being initialized), and then we enable clocksource
selection at fs_initcall (before device_initcall).
This patch should probably get some testing time in -mm, since
clocksource selection is one of the most important issues for correct
timekeeping, and I've only been able to test this on a few of my own
boxes.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When removing set_native_irq I missed the fact that it was
called in a couple of places that were compiled even when
SMP support is disabled. And since the irq_desc[].affinity
field only exists in SMP things broke.
Thanks to Simon Arlott <simon@arlott.org> for spotting this.
There are a couple of ways to fix this but the simplest one
is to just remove the assignments. The affinity field is only
used to display a value to the user, and nothing on either i386
or x86_64 reads it or depends on it being any particlua value,
so skipping the assignment is safe. The assignment that
is being removed is just for the initial affinity value before
the user explicitly sets it. The irq_desc array initializes
this field to CPU_MASK_ALL so the field is initialized to
a reasonable value in the SMP case without being set.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The problem: After moving an interrupt when is it safe to teardown
the data structures for receiving the interrupt at the old location?
With a normal pci device it is possible to issue a read to a device
to flush all posted writes. This does not work for the oldest ioapics
because they are on a 3-wire apic bus which is a completely different
data path. For some more modern ioapics when everything is using
front side bus delivery you can flush interrupts by simply issuing a
read to the ioapic. For other modern ioapics emperical testing has
shown that this does not work.
So it appears the only reliable way to know the last of the irqs from an
ioapic have been received from before the ioapic was reprogrammed is to
received the first irq from the ioapic from after it was reprogrammed.
Once we know the last irq message has been received from an ioapic
into a local apic we then need to know that irq message has been
processed through the local apics.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the ISA irqs we reserve 16 vectors. This patch adds constants for
those vectors and modifies the code to use them. Making the code a
little clearer and making it possible to move these vectors in the future.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code in io_apic.c and in i8259.c currently hardcode the same
vector for the timer interrupt so there is no reason for a special
assignment for the timer as the setup for the i8259 already takes care
of this.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently assign_irq_vector works mostly by side effect and returns
the results of it's changes to the caller. Which makes for a lot of
arguments to pass/return and confusion as to what to do if you need
the status but you aren't calling assign_irq_vector.
This patch stops returning values from assign_irq_vector that can be
retrieved just as easily by examining irq_cfg, and modifies the
callers to retrive those values from irq_cfg when they need them.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the io_apic.c has several parallel arrays for different
kinds of data that can be know about an irq. The parallel arrays
make the code harder to maintain and make it difficult to remove
the static limits on the number of the number of irqs.
This patch pushes irq_data and irq_vector into a irq_cfg array and
updates the code to use it.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NR_IRQ_VECTORS is currently a compatiblity define set to NR_IRQs.
This patch updates the users of NR_IRQ_VECTORS to use NR_IRQs instead
so that NR_IRQ_VECTORS can be removed.
There is still shared code with arch/i386 that uses NR_IRQ_VECTORS
so we can't remove the #define just yet :(
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we have an irq that comes from multiple io_apic pins the FINAL action
(which is io_apic_sync or nothing) needs to be called for every entry or
else if the two pins come from different io_apics we may not wait until
after the action happens on the io_apic.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some reason the code has been picking TARGET_CPUS when asked to
set the affinity to an empty set of cpus. That is just silly it's
extra work. Instead if there are no cpus to set the affinity to we
should just give up immediately. That is simpler and a little more
intuitive.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have two routines that do practically the same thing
setup_IO_APIC_irq and io_apic_set_pci_routing. This patch makes
setup_IO_APIC_irq the common factor of these two previous routines.
For setup_IO_APIC_irq all that was needed was to pass the trigger
and polarity to make the code a proper subset of io_apic_set_pci_routing.
Hopefully consolidating these two routines will improve maintenance
there were several differences that simply appear to be one routine
or the other getting it wrong.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces all instances of "set_native_irq_info(irq, mask)"
with "irq_desc[irq].affinity = mask". The latter form is clearer
uses fewer abstractions, and makes access to this field uniform
accross different architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By precomputing old_mask I remove an extra if statement, remove an
indentation level and make the code slightly easier to read.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
Now that disable_irq() defaults to delayed-disable semantics, the IRQ_DISABLED
flag is not needed anymore.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Never mask interrupts immediately upon request. Disabling interrupts in
high-performance codepaths is rare, and on the other hand this change could
recover lost edges (or even other types of lost interrupts) by conservatively
only masking interrupts after they happen. (NOTE: with this change the
highlevel irq-disable code still soft-disables this IRQ line - and if such an
interrupt happens then the IRQ flow handler keeps the IRQ masked.)
Mark i8529A controllers as 'never loses an edge'.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts x86_64 to use the GENERIC_TIME infrastructure and adds
clocksource structures for both TSC and HPET (ACPI PM is shared w/ i386).
[akpm@osdl.org: fix printk timestamps]
[akpm@osdl.org: fix printk ckeanups]
[akpm@osdl.org: hpet build fix]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for the x86_64 generic time conversion, this patch splits out
TSC and HPET related code from arch/x86_64/kernel/time.c into respective
hpet.c and tsc.c files.
[akpm@osdl.org: fix printk timestamps]
[akpm@osdl.org: cleanup]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for supporting generic timekeeping, this patch cleans up
x86-64's use of vxtime.hpet_address, changing it to just hpet_address as is
also used in i386. This is necessary since the vxtime structure will be going
away.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make the TSC synchronization code more robust, and unify it between x86_64 and
i386.
The biggest change is the removal of the 'fix up TSCs' code on x86_64 and
i386, in some rare cases it was /causing/ time-warps on SMP systems.
The new code only checks for TSC asynchronity - and if it can prove a
time-warp (if it can observe the TSC going backwards when going from one CPU
to another within a critical section), then the TSC clock-source is turned
off.
The TSC synchronization-checking code also got moved into a separate file.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Basically everything was done but I removed all element initializers from the
trailing entries to make it clear the entire last entry should be zero filled.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just various new acronyms. The new popcnt bit is in the middle
of Intel space. This looks a little weird, but I've been assured
it's ok.
Also I fixed RDTSCP for i386 which was at the wrong place.
For i386 and x86-64.
Signed-off-by: Andi Kleen <ak@suse.de>
Occasionally the kernel has bugs that result in no irq being found for a
given cpu vector. If we acknowledge the irq the system has a good chance
of continuing even though we dropped an irq message. If we continue to
simply print a message and not acknowledge the irq the system is likely to
become non-responsive shortly there after.
AK: Fixed compilation for UP kernels
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Luigi Genoni" <luigi.genoni@pirelli.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
I've seen my box paralyzed by an endless spew of
rtc: lost some interrupts at 1024Hz.
messages on the serial console. What seems to be happening is that
something real causes an interrupt to be lost and triggers the
message. But then printing the message to the serial console (from
the hpet interrupt handler) takes more than 1/1024th of a second, and
then some more interrupts are lost, so the message triggers again....
Fix this by adding a printk_ratelimit() before printing the warning.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
On the Unisys ES7000/ONE system, we encountered a problem where performing
a kexec reboot or dump on any cell other than cell 0 causes the system
timer to stop working, resulting in a hang during timer calibration in the
new kernel.
We traced the problem to one line of code in disable_IO_APIC(), which needs
to restore the timer's IO-APIC configuration before rebooting. The code is
currently using the 4-bit physical destination field, rather than using the
8-bit logical destination field, and it cuts off the upper 4 bits of the
timer's APIC ID. If we change this to use the logical destination field,
the timer works and we can kexec on the upper cells. This was tested on
two different cells (0 and 2) in an ES7000/ONE system.
For reference, the relevant Intel xAPIC spec is kept at
ftp://download.intel.com/design/chipsets/e8501/datashts/30962001.pdf,
specifically on page 334.
Signed-off-by: Benjamin M Romer <benjamin.romer@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
During kernel bootup, a new T60 laptop (CoreDuo, 32-bit) hangs about
10%-20% of the time in acpi_init():
Calling initcall 0xc055ce1a: topology_init+0x0/0x2f()
Calling initcall 0xc055d75e: mtrr_init_finialize+0x0/0x2c()
Calling initcall 0xc05664f3: param_sysfs_init+0x0/0x175()
Calling initcall 0xc014cb65: pm_sysrq_init+0x0/0x17()
Calling initcall 0xc0569f99: init_bio+0x0/0xf4()
Calling initcall 0xc056b865: genhd_device_init+0x0/0x50()
Calling initcall 0xc056c4bd: fbmem_init+0x0/0x87()
Calling initcall 0xc056dd74: acpi_init+0x0/0x1ee()
It's a hard hang that not even an NMI could punch through! Frustratingly,
adding printks or function tracing to the ACPI code made the hangs go away
...
After some time an additional detail emerged: disabling the NMI watchdog
made these occasional hangs go away.
So i spent the better part of today trying to debug this and trying out
various theories when i finally found the likely reason for the hang: if
acpi_ns_initialize_devices() executes an _INI AML method and an NMI
happens to hit that AML execution in the wrong moment, the machine would
hang. (my theory is that this must be some sort of chipset setup method
doing stores to chipset mmio registers?)
Unfortunately given the characteristics of the hang it was sheer
impossible to figure out which of the numerous AML methods is impacted
by this problem.
As a workaround i wrote an interface to disable chipset-based NMIs while
executing _INI sections - and indeed this fixed the hang. I did a
boot-loop of 100 separate reboots and none hung - while without the patch
it would hang every 5-10 attempts. Out of caution i did not touch the
nmi_watchdog=2 case (it's not related to the chipset anyway and didnt
hang).
I implemented this for both x86_64 and i686, tested the i686 laptop both
with nmi_watchdog=1 [which triggered the hangs] and nmi_watchdog=2, and
tested an Athlon64 box with the 64-bit kernel as well. Everything builds
and works with the patch applied.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
- set bad_dma_address explicitly to 0x0
- reserve 32 pages from bad_dma_address and up
- WARN_ON() a driver feeding us bad_dma_address
Thanks to Leo Duran <leo.duran@amd.com> for the suggestion.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Leo Duran <leo.duran@amd.com>
Cc: Job Mason <jdmason@kudzu.us>
Should be harmless because there is normally no memory there, but
technically it was incorrect.
Pointed out by Leo Duran
Signed-off-by: Andi Kleen <ak@suse.de>
Initialize FS and GS to __KERNEL_DS as well. The actual value of them is not
important, but it is important to reload them in protected mode. At this time,
they still retain the real mode values from initial boot. VT disallows
execution of code under such conditions, which means hardware virtualization
can not be used to boot the kernel on Intel platforms, making the boot time
painfully slow.
This requires moving the GS load before the load of GS_BASE, so just move
all the segments loads there to keep them together in the code.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The symbol is needed to manipulate page tables, and modules shouldn't
do that.
Leftover from 2.4, but no in tree module should need it now.
Signed-off-by: Andi Kleen <ak@suse.de>
This means if an illegal value is set for the segment registers there
ptrace will error out now with an errno instead of silently ignoring
it.
Signed-off-by: Andi Kleen <ak@suse.de>
Add failsafe mechanism to HPET/TSC clock calibration.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Updated to include failsafe mechanism & additional community feedback.
Patch built on latest 2.6.20-rc4-mm1 tree.
Signed-off-by: Andi Kleen <ak@suse.de>
When a machine check event is detected (including a AMD RevF threshold
overflow event) allow to run a "trigger" program. This allows user space
to react to such events sooner.
The trigger is configured using a new trigger entry in the
machinecheck sysfs interface. It is currently shared between
all CPUs.
I also fixed the AMD threshold handler to run the machine
check polling code immediately to actually log any events
that might have caused the threshold interrupt.
Also added some documentation for the mce sysfs interface.
Signed-off-by: Andi Kleen <ak@suse.de>
while debugging an unrelated problem in Xen, I noticed odd reads from
non-existent MSRs. Having now found time to look why these happen, I
came up with below patch, which
- prevents accessing MCi_MISCj with j > 0 when the block pointer in
MCi_MISC0 is zero
- accesses only contiguous MCi_MISCj until a non-implemented one is
found
- doesn't touch unimplemented blocks in mce_threshold_interrupt at all
- gives names to two bits previously derived from MASK_VALID_HI (it
took me some time to understand the code without this)
The first three items, besides being apparently closer to the spec, should
namely help cutting down on the time mce_threshold_interrupt() takes.
Signed-off-by: Andi Kleen <ak@suse.de>
P6 CPUs and Core/Core 2 CPUs which has 'architectural perf mon' feature,
only supports write of low 32 bits in Performance Monitoring Counters.
Bits 32..39 are sign extended based on bit 31 and bits 40..63 are reserved
and should be zero.
This patch:
Change x86_64 nmi handler to handle this case cleanly.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This is a tiny cleanup to increase readability
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Unlike x86, x86_64 already passes arguments in registers. The use of
regparm attribute makes no difference in produced code, and the use of
fastcall just bloats the code.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch resolves the issue of running with numa=fake=X on kernel command
line on x86_64 machines that have big IO hole. While calculating the size
of each node now we look at the total hole size in that range.
Previously there were nodes that only had IO holes in them causing kernel
boot problems. We now use the NODE_MIN_SIZE (64MB) as the minimum size of
memory that any node must have. We reduce the number of allocated nodes if
the number of nodes specified on kernel command line results in any node
getting memory smaller than NODE_MIN_SIZE.
This change allows the extra memory to be incremented in NODE_MIN_SIZE
granule and uniformly distribute among as many nodes (called big nodes) as
possible.
[akpm@osdl.org: build fix]
Signed-off-by: David Rientjes <reintjes@google.com>
Signed-off-by: Paul Menage <menage@google.com>
Signed-off-by: Rohit Seth <rohitseth@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
It makes more sense to end the stack trace with ULONG_MAX only if
nr_entries < max_entries. Otherwise, we lose one entry in the long stack
traces and cannot know whether the trace was complete or not.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
- add SWIOTLB config help text
- mention Documentation/x86_64/boot-options.txt in
Documentation/kernel-parameters.txt
- remove the duplication of the iommu kernel parameter documentation.
- Better explanation of some of the iommu kernel parameter options.
- "32MB<<order" instead of "32MB^order".
- Mention the default "order" value.
- list the four existing PCI-DMA mapping implementations of arch x86_64
- group the iommu= option keywords by PCI-DMA mapping implementation.
- Distinguish iommu= option keywords from number arguments.
- Explain the meaning of DAC and SAC.
Signed-off-by: Karsten Weiss <knweiss@science-computing.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Remove the statically allocated memory to NUMA node hash map in favor of a
dynamically allocated memory to node hash map (it is cache aligned).
This patch has the nice side effect in that it allows the hash map to grow
for systems with large amounts of memory (256GB - 1TB), but suffer from
having small PCI space tacked onto the boot node (which is somewhere
between 192MB to 512MB on the ES7000).
Signed-off-by: Amul Shah <amul.shah@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Rohit Seth <rohitseth@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This does user copies in fs write() into the page cache with write combining.
This pushes the destination out of the CPU's cache, but allows higher bandwidth
in some case.
The theory is that the page cache data is usually not touched by the
CPU again and it's better to not pollute the cache with it. Also it is a little
faster.
Signed-off-by: Andi Kleen <ak@suse.de>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@osdl.org: sparc64 fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove in-source externs, linux/init.h is included in all cases.
This is a fixups for "Dynamic kernel command-line" patch.
It also includes some uml __init fixups so that we can __initdata also its
command_line.
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delete the few remaining unnecessary calls to memset(0) after a call to
kzalloc().
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update all arch/*/kernel/vmlinux.lds.S to not include space for initramfs
when CONFIG_BLK_DEV_INITRAMFS is not selected. This saves another 4 kbytes
on most platfoms (some reserve PAGE_SIZE for initramfs).
Signed-off-by: Jean-Paul Saman <jean-paul.saman@nxp.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arch hooks arch_setup_msi_irq and arch_teardown_msi_irq are now
responsible for allocating and freeing the linux irq in addition to
setting up the the linux irq to work with the interrupt.
arch_setup_msi_irq now takes a pci_device and a msi_desc and returns
an irq.
With this change in place this code should be useable by all platforms
except those that won't let the OS touch the hardware like ppc RTAS.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (140 commits)
ACPICA: reduce table header messages to fit within 80 columns
asus-laptop: merge with ACPICA table update
ACPI: bay: Convert ACPI Bay driver to be compatible with sysfs update.
ACPI: bay: new driver is EXPERIMENTAL
ACPI: bay: make drive_bays static
ACPI: bay: make bay a platform driver
ACPI: bay: remove prototype procfs code
ACPI: bay: delete unused variable
ACPI: bay: new driver adding removable drive bay support
ACPI: dock: check if parent is on dock
ACPICA: fix gcc build warnings
Altix: Add ACPI SSDT PCI device support (hotplug)
Altix: ACPI SSDT PCI device support
ACPICA: reduce conflicts with Altix patch series
ACPI_NUMA: fix HP IA64 simulator issue with extended memory domain
ACPI: fix HP RX2600 IA64 boot
ACPI: build fix for IBM x440 - CONFIG_X86_SUMMIT
ACPICA: Update version to 20070126
ACPICA: Fix for incorrect parameter passed to AcpiTbDeleteTable during table load.
ACPICA: Update copyright to 2007.
...
- add proper __init decoration to swiotlb's init code (and the code calling
it, where not already the case)
- replace uses of 'unsigned long' with dma_addr_t where appropriate
- do miscellaneous simplicfication and cleanup
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Commit f2802e7f57 and its x86 version
(b7471c6da9) adds nmi_known_cpu() check
while parsing boot options in x86_64 and i386.
With that, "nmi_watchdog=2" stops working for me on Intel Core 2 CPU
based system.
The problem is, setup_nmi_watchdog is called while parsing the boot
option and identify_cpu is not done yet. So, the return value of
nmi_known_cpu() is not valid at this point.
So revert that check. This should not have any adverse effect as the
nmi_known_cpu() check is done again later in enable_lapic_nmi_watchdog().
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ensure that no SMI interrupts occur between the read of the HPET & TSC
in the clock calibration loop.
I noticed that a 2.66GHz system incorrectly detected the processor
clock speed about 1/7 of the time:
time.c: Detected 2660.005 MHz processor. (most of the time)
time.c: Detected 2988.203 MHz processor. (sometime)
The problem is caused by an SMI interrupt occuring in hpet_calibrate_tsc()
between the read of the HPET & TSC. Prior to switching the BIOS into
ACPI mode, it appears that every 27msec an SMI interrupt occurs. The
SMI interrupt takes 4.8 msec to process.
Note: On my test system, TICK_MIN had to be >380. I picked 5000
to minimize risk of having a value that is too small for other
platforms.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andi Kleen <ak@suse.de>
arch/x86_64/kernel/time.c | 25 +++++++++++++++++++++----
1 file changed, 21 insertions(+), 4 deletions(-)
This reverts commit b026872601, which has
been linked to several problem reports with IO-APIC and the timer.
Machines either don't boot because the timer doesn't happen, or we get
double timer interrupts because we end up double-routing the timer irq
through multiple interfaces.
See for example
http://lkml.org/lkml/2006/12/16/101http://lkml.org/lkml/2007/1/3/9http://bugzilla.kernel.org/show_bug.cgi?id=7789
about some of the discussion.
Patches to fix this cleanup exist (and have been confirmed to work fine
at least for some of the affected cases) and we'll revisit it for
2.6.21, but this late in the -rc series we're better off just reverting
the incomplete commit that caused the problems.
Suggested-by: Adrian Bunk <bunk@stusta.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Yinghai Lu <yinghai.lu@amd.com>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] longhaul: Kill off warnings introduced by recent changes.
[CPUFREQ] Uninitialized use of cmd.val in arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.c:acpi_cpufreq_target()
[CPUFREQ] Longhaul - Always guess FSB
[CPUFREQ] Longhaul - Fix up powersaver assumptions.
[CPUFREQ] longhaul: Fix up unreachable code.
[CPUFREQ] speedstep-centrino: missing space and bracket
[CPUFREQ] Bug fix for acpi-cpufreq and cpufreq_stats oops on frequency change notification
[CPUFREQ] select consistently
If caller passed the tsk, we should use it to validate a stack ptr.
Otherwise, sysrq-t and other debugging stuff doesn't work.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make x86_64 ACPI_CPU_FREQ select CPU_FREQ_TABLE like other methods do.
(although we should still eliminate as much use of 'select' as possible)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Fernando Lopez-Lezcano reported frequent scheduling latencies and audio
xruns starting at the 2.6.18-rt kernel, and those problems persisted all
until current -rt kernels. The latencies were serious and unjustified by
system load, often in the milliseconds range.
After a patient and heroic multi-month effort of Fernando, where he
tested dozens of kernels, tried various configs, boot options,
test-patches of mine and provided latency traces of those incidents, the
following 'smoking gun' trace was captured by him:
_------=> CPU#
/ _-----=> irqs-off
| / _----=> need-resched
|| / _---=> hardirq/softirq
||| / _--=> preempt-depth
|||| /
||||| delay
cmd pid ||||| time | caller
\ / ||||| \ | /
IRQ_19-1479 1D..1 0us : __trace_start_sched_wakeup (try_to_wake_up)
IRQ_19-1479 1D..1 0us : __trace_start_sched_wakeup <<...>-5856> (37 0)
IRQ_19-1479 1D..1 0us : __trace_start_sched_wakeup (c01262ba 0 0)
IRQ_19-1479 1D..1 0us : resched_task (try_to_wake_up)
IRQ_19-1479 1D..1 0us : __spin_unlock_irqrestore (try_to_wake_up)
...
<idle>-0 1...1 11us!: default_idle (cpu_idle)
...
<idle>-0 0Dn.1 602us : smp_apic_timer_interrupt (c0103baf 1 0)
...
<...>-5856 0D..2 618us : __switch_to (__schedule)
<...>-5856 0D..2 618us : __schedule <<idle>-0> (20 162)
<...>-5856 0D..2 619us : __spin_unlock_irq (__schedule)
<...>-5856 0...1 619us : trace_stop_sched_switched (__schedule)
<...>-5856 0D..1 619us : trace_stop_sched_switched <<...>-5856> (37 0)
what is visible in this trace is that CPU#1 ran try_to_wake_up() for
PID:5856, it placed PID:5856 on CPU#0's runqueue and ran resched_task()
for CPU#0. But it decided to not send an IPI that no CPU - due to
TS_POLLING. But CPU#0 never woke up after its NEED_RESCHED bit was set,
and only rescheduled to PID:5856 upon the next lapic timer IRQ. The
result was a 600+ usecs latency and a missed wakeup!
the bug turned out to be an idle-wakeup bug introduced into the mainline
kernel this summer via an optimization in the x86_64 tree:
commit 495ab9c045
Author: Andi Kleen <ak@suse.de>
Date: Mon Jun 26 13:59:11 2006 +0200
[PATCH] i386/x86-64/ia64: Move polling flag into thread_info_status
During some profiling I noticed that default_idle causes a lot of
memory traffic. I think that is caused by the atomic operations
to clear/set the polling flag in thread_info. There is actually
no reason to make this atomic - only the idle thread does it
to itself, other CPUs only read it. So I moved it into ti->status.
the problem is this type of change:
if (!hlt_counter && boot_cpu_data.hlt_works_ok) {
- clear_thread_flag(TIF_POLLING_NRFLAG);
+ current_thread_info()->status &= ~TS_POLLING;
smp_mb__after_clear_bit();
while (!need_resched()) {
local_irq_disable();
this changes clear_thread_flag() to an explicit clearing of TS_POLLING.
clear_thread_flag() is defined as:
clear_bit(flag, &ti->flags);
and clear_bit() is a LOCK-ed atomic instruction on all x86 platforms:
static inline void clear_bit(int nr, volatile unsigned long * addr)
{
__asm__ __volatile__( LOCK_PREFIX
"btrl %1,%0"
hence smp_mb__after_clear_bit() is defined as a simple compile barrier:
#define smp_mb__after_clear_bit() barrier()
but the explicit TS_POLLING clearing introduced by the patch:
+ current_thread_info()->status &= ~TS_POLLING;
is not an atomic op! So the clearing of the TS_POLLING bit is freely
reorderable with the reading of the NEED_RESCHED bit - and both now
reside in different memory addresses.
CPU idle wakeup very much depends on ordered memory ops, the clearing of
the TS_POLLING flag must always be done before we test need_resched()
and hit the idle instruction(s). [Symmetrically, the wakeup code needs
to set NEED_RESCHED before it tests the TS_POLLING flag, so memory
ordering is paramount.]
Fernando's dual-core Athlon64 system has a sufficiently advanced memory
ordering model so that it triggered this scenario very often.
( And it also turned out that the reason why these latencies never
triggered on my testsystems is that i routinely use idle=poll, which
was the only idle variant not affected by this bug. )
The fix is to change the smp_mb__after_clear_bit() to an smp_mb(), to
act as an absolute barrier between the TS_POLLING write and the
NEED_RESCHED read. This affects almost all idling methods (default,
ACPI, APM), on all 3 x86 architectures: i386, x86_64, ia64.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Fernando Lopez-Lezcano <nando@ccrma.Stanford.EDU>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
if CONFIG_CALGARY_IOMMU is built into the kernel via
CONFIG_CALGARY_IOMMU_ENABLED_BY_DEFAULT, or is enabled via the
iommu=calgary boot option, then the detect_calgary() function runs to
detect the presence of a Calgary IOMMU.
detect_calgary() first searches the BIOS EBDA area for a "rio_table_hdr"
BIOS table. It has this parsing algorithm for the EBDA:
while (offset) {
...
/* The next offset is stored in the 1st word. 0 means no more */
offset = *((unsigned short *)(ptr + offset));
}
got that? Lets repeat it slowly: we've got a BIOS-supplied data
structure, plus Linux kernel code that will only break out of an
infinite parsing loop once the BIOS gives a zero offset. Ok?
Translation: what an excellent opportunity for BIOS writers to lock up
the Linux boot process in an utterly hard to debug place! Indeed the
BIOS jumped on that opportunity on my box, which has the following EBDA
chaining layout:
384, 65282, 65535, 65535, 65535, 65535, 65535, 65535 ...
see the pattern? So my, definitely non-Calgary system happily locks up
in detect_calgary()!
the patch below fixes the boot hang by trusting the BIOS-supplied data
structure a bit less: the parser always has to make forward progress,
and if it doesnt, we break out of the loop and i get the expected kernel
message:
Calgary: Unable to locate Rio Grande Table in EBDA - bailing!
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It has caused more problems than it ever really solved, and is
apparently not getting cleaned up and fixed. We can put it back when
it's stable and isn't likely to make warning or bug events worse.
In the meantime, enable frame pointers for more readable stack traces.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new PDA code uses a dummy _proxy_pda variable to describe
memory references to the PDA. It is never referenced
in inline assembly, but exists as input/output arguments.
gcc 4.2 in some cases can CSE references to this which causes
unresolved symbols. Define it to zero to avoid this.
Signed-off-by: Andi Kleen <ak@suse.de>
2.6.19 stopped booting (or booted based on build/config) on our x86_64
systems due to a bug introduced in 2.6.19. check_nmi_watchdog schedules an
IPI on all cpus to busy wait on a flag, but fails to set the busywait
flag if NMI functionality is disabled. This causes the secondary cpus
to spin in an endless loop, causing the kernel bootup to hang.
Depending upon the build, the busywait flag got overwritten (stack variable)
and caused the kernel to bootup on certain builds. Following patch fixes
the bug by setting the busywait flag before returning from check_nmi_watchdog.
I guess using a stack variable is not good here as the calling function could
potentially return while the busy wait loop is still spinning on the flag.
AK: I redid the patch significantly to be cleaner
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This makes x86-64 use the generic BUG machinery.
The main advantage in using the generic BUG machinery for x86-64 is that
the inlined overhead of BUG is just the ud2a instruction; the file+line
information are no longer inlined into the instruction stream. This
reduces cache pollution.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andi Kleen <ak@muc.de>
Cc: Hugh Dickens <hugh@veritas.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The elf note saving code is currently duplicated over several
architectures. This cleanup patch simply adds code to a common file and
then replaces the arch-specific code with calls to the newly added code.
The only drawback with this approach is that s390 doesn't fully support
kexec-on-panic which for that arch leads to introduction of unused code.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was lots of #ifdef noise in the kernel due to hotcpu_notifier(fn,
prio) not correctly marking 'fn' as used in the !HOTPLUG_CPU case, and thus
generating compiler warnings of unused symbols, hence forcing people to add
#ifdefs.
the compiler can skip truly unused functions just fine:
text data bss dec hex filename
1624412 728710 3674856 6027978 5bfaca vmlinux.before
1624412 728710 3674856 6027978 5bfaca vmlinux.after
[akpm@osdl.org: topology.c fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
smp_call_function_single() can deadlock if the caller disabled local
interrupts (the target CPU could be spinning on call_lock). Check for that.
Why on earth do these functions use spin_lock_bh()??
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we are unregistering a kprobe-booster, we can't release its
instruction buffer immediately on the preemptive kernel, because some
processes might be preempted on the buffer. The freeze_processes() and
thaw_processes() functions can clean most of processes up from the buffer.
There are still some non-frozen threads who have the PF_NOFREEZE flag. If
those threads are sleeping (not preempted) at the known place outside the
buffer, we can ensure safety of freeing.
However, the processing of this check routine takes a long time. So, this
patch introduces the garbage collection mechanism of insn_slot. It also
introduces the "dirty" flag to free_insn_slot because of efficiency.
The "clean" instruction slots (dirty flag is cleared) are released
immediately. But the "dirty" slots which are used by boosted kprobes, are
marked as garbages. collect_garbage_slots() will be invoked to release
"dirty" slots if there are more than INSNS_PER_PAGE garbage slots or if
there are no unused slots.
Cc: "Keshavamurthy, Anil S" <anil.s.keshavamurthy@intel.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "bibo,mao" <bibo.mao@intel.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Yumiko Sugita <yumiko.sugita.yf@hitachi.com>
Cc: Satoshi Oshima <soshima@redhat.com>
Cc: Hideo Aoki <haoki@redhat.com>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After LOADER_TYPE && INITRD_START are true, the short if-condition
for INITRD_START can never be false.
Remove unused code from the else condition.
Signed-off-by: Henry Nestler <henry.ne@arcor.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The last thing we agreed on was to remove the macros entirely for 2.6.19,
on all architectures. Unfortunately, I think nobody actually _did_ that,
so they are still there.
[akpm@osdl.org: x86_64 fix]
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Schafer <gschafer@zip.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The .eh_frame section contents is never written to, so it can as well
benefit from CONFIG_DEBUG_RODATA.
Diff-ed against firstfloor tree.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
setup_IO_APIC_irqs could fail to get vector for some device when you have too
many devices, because at that time only boot cpu is online. So check vector
for irq in setup_ioapic_dest and call setup_IO_APIC_irq to make sure IO-APIC
irq-routing table is initialized.
Also seperate setup_IO_APIC_irq from setup_IO_APIC_irqs.
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
- Remove "Disabling IOMMU" message because it confuses people
- Clarify that the GART IOMMU is refered to in other message
Signed-off-by: Andi Kleen <ak@suse.de>
Idle callbacks has some races when enter_idle() sets isidle and subsequent
interrupts that can happen on that CPU, before CPU goes to idle. Due to this,
an IDLE_END can get called before IDLE_START. To avoid these races, disable
interrupts before enter_idle and make sure that all idle routines do not
enable interrupts before entering idle.
Note that poll_idle() still has a this race as it has to enable interrupts
before going to idle. But, all other idle routines have the race fixed.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This was added as a workaround for the fallback unwinder not supporting
unaligned stack pointers properly. But now it was fixed to do that,
so it's not needed anymore
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
Tighten the requirements on both input to and output from the Dwarf2
unwinder.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
We're already well protected against module unloads because module
unload uses stop_machine(). The only exception is NMIs, but other
users already risk lockless accesses here.
This avoids some hackery in lockdep and also a potential deadlock
This matches what i386 does.
Signed-off-by: Andi Kleen <ak@suse.de>
On the Core2 cpus, the rdtsc instruction is not serializing (as defined
in the architecture reference since rdtsc exists) and due to the deep
speculation of these cores, it's possible that you can observe time go
backwards between cores due to this speculation. Since the kernel
already deals with this with the SYNC_RDTSC flag, the solution is
simple, only assume that the instruction is serializing on family 15...
The price one pays for this is a slightly slower gettimeofday (by a
dozen or two cycles), but that increase is quite small to pay for a
really-going-forward tsc counter.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
There is no guarantee that two RDTSCs in a row are monotonic,
so don't assume it on single core AMD systems.
This will make gettimeofday slower again
Signed-off-by: Andi Kleen <ak@suse.de>
Make mce_remove_device() clean up the kobject in per_cpu(device_mce, cpu)
after it has been unregistered.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@suse.de>
interrupt array is referred for idt vectors instead of NR_IRQS, so change size
to NR_VECTORS - FIRST_EXTERNAL_VECTOR. Also change to static.
Signed-off-by: Yinghai Lu <yinghai@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
idt_table is in the .bss section, so clear_bss need to called at first
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Add sysctl for kstack_depth_to_print. This lets users change
the amount of raw stack data printed in dump_stack() without
having to reboot.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Read/Write APIC_LVTPC and APIC_LVTTHMR only,
if get_maxlvt() returns certain values.
This is done like everywhere else in i386/kernel/apic.c,
so I guess its correct.
Suspends/Resumes to disk fine and eleminates an smp_error_interrupt()
here on a K8.
AK: ported to x86-64 too
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Here is a small patch for x86-64 which adds a cpufeature flag and
detection code for Intel's Branch Trace Store (BTS) feature. This
feature can be found on Intel P4 and Core 2 processors among others.
It can also be used by perfmon.
changelog:
- add CPU_FEATURE_BTS
- add Branch Trace Store detection
signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Move the irqbalance quirks for E7320/E7520/E7525(Errata 23 in
http://download.intel.com/design/chipsets/specupdt/30304203.pdf) to early
quirks.
And add a PCI quirk for these platforms to check(which happens very late
during the boot) if the APIC routing is indeed set to default flat mode.
This fixes the breakage(in x86_64) of this quirk due to cpu hotplug which
selects physical mode instead of the logical flat(as needed for this errata
workaround).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The final line of /proc/<pid>/maps on x86_64 for native 64-bit
tasks shows an incorrect ending address and incorrect permissions. There
is only a single page mapped in this vsyscall region, and it is accessible
for both read and execute.
The patch below fixes this. (Since 32-bit-compat tasks have a real vma
with correct perms/range, no change is necessary for that scenario.)
Before the patch, a "cat /proc/self/maps | tail -1" shows this:
ffffffffff600000-ffffffffffe00000 ---p 00000000 [...]
After the patch, this is the output:
ffffffffff600000-ffffffffff601000 r-xp 00000000 [...]
Signed-off-by: Ernie Petrides <petrides@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch makes it possible to compile Calgary in but not use it by
default. In this mode, use 'iommu=calgary' to activate it.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch cleans up the previous "Use BIOS supplied BBAR information"
patch. Mostly stylistic clenaups, but also check for ioremap failure
when we ioremap the BBAR rather than when trying to use it.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Laurent Vivier <Laurent.Vivier@bull.net>
Find the BBAR register address of each Calgary using the "Extended
BIOS Data Area" rather than calculating it ourselves. Also get the bus
topology (what PHB each bus is on) from Calgary rather than
calculating it ourselves.
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=7407.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Andi Kleen <ak@suse.de>
Instead of adding all kinds of more quirks try various timer
routing variants in check_timer.
In particular this tries to handle quirks from:
- Nvidia NF2-4 reference BIOS: wrong timer override
- Asus: Wrong timer override but no HPET table
- ATI: require timer disabled in 8259
- Some boards: require timer enabled in 8259
We just try many of the the known variants in the hopefully right order
in check_timer.
Trying pin 0/2 on Nvidia suggested by Tim Hockin.
TBD Experimental. Needs a lot of testing
Signed-off-by: Andi Kleen <ak@suse.de>
Clear the irq releated entries in irq_vector, irq_domain and vector_irq
instead of clearing irq_vector only. So when new irq is created, it
could reuse that vector. (actually is the second loop scanning from
FIRST_DEVICE_VECTOR+8). This could avoid the vectors are used up
with enough module inserting and removing
Cc: Eric W. Biedierman <ebiederm@xmission.com>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-By: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
