sz is in bytes, MAX_ORDER_NR_PAGES is in pages.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: David Gibson <dwg@au1.ibm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: David Rientjes <rientjes@google.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously enabled poll(2) support on one edge was never reconfigured when
sysfs polarity change was triggered from kernel, because 'struct device
*dev' shadowed an earlier definition.
Found by sparse, which I should've run much earlier.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Josip Rodin <joy@entuzijast.net>
Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main bug was that 'blk_cleanup_queue()' was called while the block
device could still be in use, for example, because the card was removed
while files were still open.
In addition, to be sure that 'mmc_request()' will get called for all new
requests (so it can error them out), the queue is emptied during cleanup.
This is done after the worker thread is stopped to avoid racing with it.
Finally, it is not a device error for this to be happening, so quiet the
(sometimes very many) error messages.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If mmc_blk_set_blksize() fails mmc_blk_probe() the request queue and its
thread have been set up and they need to be shut down properly before
putting the disk.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a card is removed before mmc_blk_probe() has called add_disk(), then
the minor field is uninitialized and has value 0. This caused
mmc_blk_put() to always release devidx 0 even if 0 was still in use. Then
the next mmc_blk_probe() used the first free idx of 0, which oopses in
sysfs, since it is used by another card.
Signed-off-by: Anna Lemehova <EXT-Anna.Lemehova@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Warning(drivers/base/power/main.c:453): No description found for parameter 'dev'
Warning(drivers/base/power/main.c:453): No description found for parameter 'cb'
Warning(drivers/base/power/main.c:719): No description found for parameter 'dev'
Warning(drivers/base/power/main.c:719): No description found for parameter 'state'
Warning(drivers/base/power/main.c:719): No description found for parameter 'cb'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d899bf7b (procfs: provide stack information for threads) introduced
to show stack information in /proc/{pid}/status. But it cause large
performance regression. Unfortunately /proc/{pid}/status is used ps
command too and ps is one of most important component. Because both to
take mmap_sem and page table walk are heavily operation.
If many process run, the ps performance is,
[before d899bf7b]
% perf stat ps >/dev/null
Performance counter stats for 'ps':
4090.435806 task-clock-msecs # 0.032 CPUs
229 context-switches # 0.000 M/sec
0 CPU-migrations # 0.000 M/sec
234 page-faults # 0.000 M/sec
8587565207 cycles # 2099.425 M/sec
9866662403 instructions # 1.149 IPC
3789415411 cache-references # 926.409 M/sec
30419509 cache-misses # 7.437 M/sec
128.859521955 seconds time elapsed
[after d899bf7b]
% perf stat ps > /dev/null
Performance counter stats for 'ps':
4305.081146 task-clock-msecs # 0.028 CPUs
480 context-switches # 0.000 M/sec
2 CPU-migrations # 0.000 M/sec
237 page-faults # 0.000 M/sec
9021211334 cycles # 2095.480 M/sec
10605887536 instructions # 1.176 IPC
3612650999 cache-references # 839.160 M/sec
23917502 cache-misses # 5.556 M/sec
152.277819582 seconds time elapsed
Thus, this patch revert it. Fortunately /proc/{pid}/task/{tid}/smaps
provide almost same information. we can use it.
Commit d899bf7b introduced two features:
1) Add the annotattion of [thread stack: xxxx] mark to
/proc/{pid}/task/{tid}/maps.
2) Add StackUsage field to /proc/{pid}/status.
I only revert (2), because I haven't seen (1) cause regression.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Stefani Seibold <stefani@seibold.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MIPS compressed kernels output a vmlinuz file in the top-level directory
(maybe others do). Add vmlinuz to the list of files to ignore by git.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When print-fatal-signals is enabled it's possible to dump any memory
reachable by the kernel to the log by simply jumping to that address from
user space.
Or crash the system if there's some hardware with read side effects.
The fatal signals handler will dump 16 bytes at the execution address,
which is fully controlled by ring 3.
In addition when something jumps to a unmapped address there will be up to
16 additional useless page faults, which might be potentially slow (and at
least is not very efficient)
Fortunately this option is off by default and only there on i386.
But fix it by checking for kernel addresses and also stopping when there's
a page fault.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LTP cgroup test suite generates a "kernel BUG at kernel/cgroup.c:790!"
here in cgroup_diput():
/*
* if we're getting rid of the cgroup, refcount should ensure
* that there are no pidlists left.
*/
BUG_ON(!list_empty(&cgrp->pidlists));
The cgroup pidlist rework in 2.6.32 generates the BUG_ON, which is caused
when pidlist_array_load() calls cgroup_pidlist_find():
(1) if a matching cgroup_pidlist is found, it down_write's the mutex of the
pre-existing cgroup_pidlist, and increments its use_count.
(2) if no matching cgroup_pidlist is found, then a new one is allocated, it
down_write's its mutex, and the use_count is set to 0.
(3) the matching, or new, cgroup_pidlist gets returned back to pidlist_array_load(),
which increments its use_count -- regardless whether new or pre-existing --
and up_write's the mutex.
So if a matching list is ever encountered by cgroup_pidlist_find() during
the life of a cgroup directory, it results in an inflated use_count value,
preventing it from ever getting released by cgroup_release_pid_array().
Then if the directory is subsequently removed, cgroup_diput() hits the
BUG_ON() when it finds that the directory's cgroup is still populated with
a pidlist.
The patch simply removes the use_count increment when a matching pidlist
is found by cgroup_pidlist_find(), because it gets bumped by the calling
pidlist_array_load() function while still protected by the list's mutex.
Signed-off-by: Dave Anderson <anderson@redhat.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: Paul Menage <menage@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following command doesn't generate any output.
`./scripts/get_maintainer.pl --no-git -f drivers/net/wireless/wl12xx/wl1271_acx.c`
An excluded "X:" pattern match in any section would cause a file not to
match any other section.
Signed-off-by: Joe Perches <joe@perches.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lib/rational.c:62: warning: data definition has no type or storage class
lib/rational.c:62: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
lib/rational.c:62: warning: parameter names (without types) in function declaration
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Oskar Schirmer <os@emlix.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- changes to ach/arch/boot/Makefile to make it easier to add new
compression types
- new piggy.lzo.S necessary for lzo compression
- changes in arch/arm/boot/compressed/misc.c to allow the use of lzo or
gzip, depending on the config
- Kconfig support
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series adds generic support for creating and extracting
LZO-compressed kernel images, as well as support for using such images on
the x86 and ARM architectures, and support for creating and using
LZO-compressed initrd and initramfs images.
Russell King said:
: Testing on a Cortex A9 model:
: - lzo decompressor is 65% of the time gzip takes to decompress a kernel
: - lzo kernel is 9% larger than a gzip kernel
:
: which I'm happy to say confirms your figures when comparing the two.
:
: However, when comparing your new gzip code to the old gzip code:
: - new is 99% of the size of the old code
: - new takes 42% of the time to decompress than the old code
:
: What this means is that for a proper comparison, the results get even better:
: - lzo is 7.5% larger than the old gzip'd kernel image
: - lzo takes 28% of the time that the old gzip code took
:
: So the expense seems definitely worth the effort. The only reason I
: can think of ever using gzip would be if you needed the additional
: compression (eg, because you have limited flash to store the image.)
:
: I would argue that the default for ARM should therefore be LZO.
This patch:
The lzo compressor is worse than gzip at compression, but faster at
extraction. Here are some figures for an ARM board I'm working on:
Uncompressed size: 3.24Mo
gzip 1.61Mo 0.72s
lzo 1.75Mo 0.48s
So for a compression ratio that is still relatively close to gzip, it's
much faster to extract, at least in that case.
This part contains:
- Makefile routine to support lzo compression
- Fixes to the existing lzo compressor so that it can be used in
compressed kernels
- wrapper around the existing lzo1x_decompress, as it only extracts one
block at a time, while we need to extract a whole file here
- config dialog for kernel compression
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
JFFS2 uses lesser compression ratio and inflate always ends up in "copy
direct from output" case.
This patch tries to optimize the direct copy procedure. Uses
get_unaligned() but only in one place.
The copy loop just above this one can also use this optimization, but I
havn't done so as I have not tested if it is a win there too.
On my MPC8321 this is about 17% faster on my JFFS2 root FS than the
original.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__pcpu_ptr_to_addr() can be overridden by the architecture and might not
behave well if passed a NULL pointer. So avoid calling it until we have
verified that its arg is not NULL.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix resource (write-pipe file) leak in call_usermodehelper_pipe().
When call_usermodehelper_exec() fails, write-pipe file is opened and
call_usermodehelper_pipe() just returns an error. Since it is hard for
caller to determine whether the error occured when opening the pipe or
executing the helper, the caller cannot close the pipe by themselves.
I've found this resoruce leak when testing coredump. You can check how
the resource leaks as below;
$ echo "|nocommand" > /proc/sys/kernel/core_pattern
$ ulimit -c unlimited
$ while [ 1 ]; do ./segv; done &> /dev/null &
$ cat /proc/meminfo (<- repeat it)
where segv.c is;
//-----
int main () {
char *p = 0;
*p = 1;
}
//-----
This patch closes write-pipe file if call_usermodehelper_exec() failed.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no need to perform full BIDIR sync (copying the buffers in case
of swiotlb and similar schemes) if we know that the owner (CPU or device)
hasn't altered the data.
Addresses the false-positive reported at
http://bugzilla.kernel.org/show_bug.cgi?id=14169
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: David Miller <davem@davemloft.net>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that even zero-sized struct members (int foo[0];) will affect
the struct layout, causing us in particular to lose 4 bytes in struct
sock.
This patch fixes the regression in CONFIG_KMEMCHECK=n case.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add many ioctl definitions to ioctl-number.txt.
Fix some whitespace/formatting.
Correct some filenames/paths.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes it consistent with the extern declaration, used when CONFIG_HIGHMEM
is set Removes redundant casts in printout messages
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit cbda12d77e (drm/i915: implement
new pm ops for i915), among other things, removed the .suspend and
.resume pointers from the struct drm_driver object in i915_drv.c,
which broke resume without KMS on my MSI Wind U100.
Fix this by reverting that part of commit cbda12d77e.
[ The DRM layer will not use the class-specific suspend/resume functions
if the driver is marked MODESET-aware, and conversely it will not
register the PCI device if the drievr isn't so marked, so you always
end up with _either_ the drm-class suspend/resume _or_ the PCI layer
PM functionality, never both. - Linus ]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb: Fix kernel-doc format error in kgdb.h
blackfin,kgdb: Do not put PC in gdb_regs into retx.
blackfin,kgdb,probe_kernel: Cleanup probe_kernel_read/write
maccess,probe_kernel: Allow arch specific override probe_kernel_(read|write)
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86, irq: Check move_in_progress before freeing the vector mapping
x86: copy_from_user() should not return -EFAULT
Revert "x86: Side-step lguest problem by only building cmpxchg8b_emu for pre-Pentium"
x86/pci: Intel ioh bus num reg accessing fix
x86: Fix size for ex trampoline with 32bit
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
nfs: fix oops in nfs_rename()
sunrpc: fix build-time warning
sunrpc: on successful gss error pipe write, don't return error
SUNRPC: Fix the return value in gss_import_sec_context()
SUNRPC: Fix up an error return value in gss_import_sec_context_kerberos()
Randy Dunlap Reported printk() format-related warnings reported
on i386 builds in his environment. Dave Chinner provided this
patch to eliminate them.
Signed-off by: Dave Chinner <david@fromorbit.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] __per_cpu_idtrs[] is a memory hog
[IA64] sanity in #include files. Move fnptr to types.h
[IA64] use helpers for rlimits
[IA64] cpumask_of_node() should handle -1 as a node
__per_cpu_idtrs is statically allocated ... on CONFIG_NR_CPUS=4096
systems it hogs 16MB of memory. This is way too much for a quite
probably unused facility (only KVM uses dynamic TR registers).
Change to an array of pointers, and allocate entries as needed on
a per cpu basis. Change the name too as the __per_cpu_ prefix is
confusing (this isn't a classic <linux/percpu.h> type object).
Signed-off-by: Tony Luck <tony.luck@intel.com>
linux-next-20081022//include/linux/kgdb.h:308): duplicate section name 'Description'
and fix typos in that file's kernel-doc comments.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
In blackfin, kgdb is running in delayed exception IRQ5 other than in
exception IRQ3 directly. Register reti other than retx in pt_regs is
the kgdb return address. So, don't put PC in gdb_regs into retx.
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Blackfin needs it own arch specific probe_kernel_read() and
probe_kernel_write().
This was moved out of the kgdb code and into the
arch/blackfin/maccess.c, because it is a generic kernel api.
The arch specific kgdb.c for blackfin was cleaned of all functions
which exist in the kgdb core that do the same thing after resolving
the probe_kernel_read() and probe_kernel_write(). This also
eliminated the need for most of the #include's.
CC: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some archs such as blackfin, would like to have an arch specific
probe_kernel_read() and probe_kernel_write() implementation which can
fall back to the generic implementation if no special operations are
needed.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fix remaining xattr locks acquired in reiserfs_xattr_set_handle()
while we are holding the reiserfs lock to avoid lock inversions.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Stanse found an unreachable statement in reiserfs_ioctl. There is a
if followed by error assignment and `break' with no braces. Add the
braces so that we don't break every time, but only in error case,
so that REISERFS_IOC_SETVERSION actually works when it returns no
error.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Reiserfs <reiserfs-devel@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
reiserfs_get_acl is usually not called under the reiserfs lock,
as it doesn't need it. But it happens when it is called by
reiserfs_acl_chmod(), which creates a dependency inversion against
the private xattr inodes mutexes for the given inode.
We need to call it without the reiserfs lock, especially since
it's unnecessary.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/kms: Fix &&/|| confusion in drm_fb_helper_connector_parse_command_line()
drm/edid: Fix CVT width/height decode
drm/edid: Skip empty CVT codepoints
drm: remove address mask param for drm_pci_alloc()
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
* korg/drm-radeon-next:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
