Tegra210 has 3 DMIC inputs which can be clocked from the recovered clock
of several other audio inputs (eg. i2s0, i2s1, ...). To model this, we
add a 3 new clocks similar to the audio* clocks which handle the same
function for the I2S and SPDIF clocks.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is used to clock the HDMI CEC interface.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When used as part of fractional ndiv calculations, the current range is
not enough because the denominator of the fraction is multiplied with m.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Return the actually achieved rate in cfg->output_rate rather than just
the requested rate. This is important to make clk_round_rate() return
the correct result.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the PLL is on, only warn if the defaults are not yet set. Otherwise
be silent.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock doesn't actually exist, so remove it.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The parent for afi is actually mselect, not clk_m.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The 2 ISP clocks (ispa and ispb) share a mux/divider control. So model
this as 1 mux/divider clock and child gate clocks.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
pll_a1 was using CLK_RST_CONTROLLER_PLLA1_MISC_0 for IDDQ control rather
than the correct register CLK_RST_CONTROLLER_PLLA1_MISC_1. Also add
pll_a1 to the set of clocks defined for Tegra210.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In commit e66f81bbd7 ("clk: sunxi-ng: Implement factors offsets"), the
final formula of NKMP clocks' recalc_rate is refactored; however, the
refactored formula broke the calculation due to some C language operand
priority problem -- the priority of operand >> is lower than * and /,
makes the formula being parsed as "(parent_rate * n * k) >> (p / m)", but
it should be "(parent_rate * n * k >> p) / m".
Add the pair of parentheses to fix up this issue. This pair of
parentheses used to exist in the old formula.
Fixes: e66f81bbd7 ("clk: sunxi-ng: Implement factors offsets")
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The mult/div for osc12M was previously backwards (giving a 48M rate
for osc12M). Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Expose clock CLKID_RNG0 which is needed for the HW random number generator.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With the newly introduced clk type for muxes in the grf we now can
describe some missing clocks, like the clk_gmac2io and clk_gmac2phy
that selects between clk_mac2io_src and gmac_clkin based on a bit
set in the general register files.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently, TI clock driver uses an encapsulated struct that is cast into
a void pointer to store all register addresses. This can be considered
as rather nasty hackery, and prevents from expanding the register
address field also. Instead, replace all the code to use proper struct
in place for this, which contains all the previously used data.
This patch is rather large as it is touching multiple files, but this
can't be split up as we need to avoid any boot breakage.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
clksel register pointer should be used for the DPLL-MX autoidle handling.
Currently this is not setup at all. Fix by adding proper handling for the
register.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
These are going to be used by the clkctrl support that will be introduced
later.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This can be used from the divider itself, and also from the clkctrl
clocks once this is introduced.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Instead of using the generic clock driver data struct, use one internal
for the TI clock driver itself. This allows modifying the register access
parts in subsequent patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Instead of using the generic clock driver data struct, use one internal
for the TI clock driver itself. This allows modifying the register access
parts in subsequent patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This has been superceded by the usage of ti_clk_ll_ops for now.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cleanup any unnecessary DT_CLK() alias entries from the OMAP4 clock file.
Most of these are now handled dynamically by the driver code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Constant string arrays should use const char * const instead of just
const char *. Change the implementations using these to proper type.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This is not needed outside the driver, so move it inside it and remove
the prototype from the public header also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This API generates clock aliases automatically for simple clock types
(fixed-clock, fixed-factor-clock), so that we don't need to add the data
for these statically into tables. Shall be called from the SoC specific
clock init.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Large portions of the OMAP framework still depend on the support of
having clock aliases in place, so add support functions for generating
these automatically.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The shared uart-pll is on boot a child of the apll that can get changed
by cpu frequency scaling. So move it away to the more stable gpll to
make sure the uart doesn't break on cpu frequency changes.
This turned up during the 4.11 merge-window when commit
6a171b2993 ("serial: 8250_dw: Allow hardware flow control to be used")
added general termios enablement making the uart on rk3036 change
frequency and thus making it susceptible for the frequency scaling issue.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The mux_pll_src_apll_dpll_gpll_usb480m_p parent list was missing a ","
between the 3rd and 4th parent names, making them fall together and thus
lookups fail. Fix that.
Fixes: 5190c08b29 ("clk: rockchip: add clock controller for rk3036")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some drivers use sprintf to build clk connection id names but the clk
core will save those strings and occasionally print them back. Duplicate
the con_id strings instead of fixing all the users.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the IMR[0-3] clocks to the R8A7795 CPG/MSSR driver.
Based on the original (and large) patch by Konstantin Kozhevnikov
<Konstantin.Kozhevnikov@cogentembedded.com>.
Signed-off-by: Konstantin Kozhevnikov <Konstantin.Kozhevnikov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tighten the depends on the various AllWinn SoCs so we don't
inadvertantly get clock drivers when we're not wanting them
like 32 bit SoC clocks for 64 bit configs. Ensure there's
still test coverage though.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner H5 is a SoC that features a design which keeps the peripheral
compatible with H3, so that it have also a CCU like the one on H3 --
only one bus gate/reset is added, and the mmc sample/output phases are
removed because of MMC controller update.
Add its support in our existing H3 CCU driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clock gates have a pre-divider between the source input and the
gate itself. A notable example is the HSIC 12 MHz clock found on the
A83T, which has the 24 MHz main oscillator as its input, and a /2
pre-divider.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The enable bit offset for the hdmi-ddc module clock is wrong. It is
pointing to the main hdmi module clock enable bit.
Reported-by: Bob Ham <rah@settrans.net>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: stable@vger.kernel.org # 4.9.x-
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A randconfig build ran into this rare link error:
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.1+0x4): undefined reference to `ccu_nkmp_ops'
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.7+0x4): undefined reference to `ccu_nkmp_ops'
This adds the missing 'select'.
Fixes: 5e73761786 ("clk: sunxi-ng: Add sun5i CCU driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The MP style clocks support an mux with pre-dividers. While the driver
correctly accounted for them in the .determine_rate callback, it did
not in the .recalc_rate and .set_rate callbacks.
This means when calculating the factors in the .set_rate callback, they
would be off by a factor of the active pre-divider. Same goes for
reading back the clock rate after it is set.
Cc: stable@vger.kernel.org
Fixes: 2ab836db50 ("clk: sunxi-ng: Add M-P factor clock support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PMU Cortex M0 on rk3399 is intended to be used for things like
DDRFreq transitions, suspend/resume, and other things that are the
purview of ARM Trusted Firmware and not the kernel. As such, the
kernel shouldn't be messing with the clocks. Add CLK_IGNORE_UNUSED to
these clocks.
Without this change, the following was observed on a Chromebook with a
rk3399 (using not-yet-upstream ARM Trusted Firmware code and
not-yet-upstream kernel code based on kernel-4.4):
1. We init the clock framework.
2. We start up "DDRFreq", which causes ATF to occasionally fire up the
M0 for transitions. Each time ATF fires up the M0 it will turn on
these clocks and each time it is done it will turn them off.
3. We finally get to the the part of the kernel that calls
clk_disable_unused() and we disables the clocks.
You can see the race above. Basically everything is fine as long as
ARM Trusted Firmware isn't starting up the M0 at exactly the same time
that the kernel is disabling unused clocks. ...but if the race
happens then we go boom.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
This includes two branches for arm64 dt updates, both following up
on earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the
start of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=A3U6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
This includes two branches for arm64 dt updates, both following up on
earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the start
of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: deconfig: fix the moxart defconfig
ARM: ux500: resume the second core properly
arm64: dts: juno: update definition for programmable replicator
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
ARM64: dts: meson-gxbb-p200: add ADC laddered keys
ARM64: dts: meson: meson-gx: add the SAR ADC
ARM64: dts: meson-gxl: add the pwm_ao_b pin
ARM64: dts: meson-gx: add the missing pwm_AO_ab node
clk: gxbb: fix CLKID_ETH defined twice
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
clk: gxbb: add the SAR ADC clocks and expose them
dt-bindings: amlogic: Add WeTek boards
ARM64: dts: meson-gxbb: Add support for WeTek Hub and Play
dt-bindings: vendor-prefix: Add wetek vendor prefix
ARM64: dts: meson-gxm: Rename q200 and q201 DT files for consistency
ARM64: dts: meson-gx: Add HDMI HPD/DDC pinctrl nodes
...
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJYsLxxAAoJEK0CiJfG5JUl0p0P/AiBaYvrmHBx3H9jdC3iQxd2
7luFN3OqpykmZc3xx2xO3WaZ96kwwxiMu8sj3+VQo6oCkEuOY2ru6uPiDOcF4P3+
8ku2taoWlESDbVLebVTNJoRXBaBLaV+9BCN7AKvXpVw+/UkJI5hgr0yMdh4tgtvu
K08tTMkDNDbA33KXuJo8/chQFqi2W6XBXk22YMkqqA8jx0F4EM759LcgUlD1YfBS
HKkgSOgsW3Zwhl27ZEAJMthcmS4+wFaEgFBeipg/hxTLI3aQtmDtRfXwg0wkbBx2
8sVz9SyBwkjOT9+41kve+Je94NK3blnJEjbxPASveMwyhdX1TlDQCPfrXya/1zxz
N1By1NpA6iEYwi4hy+OtBYlcsBHztAM/+eljDY2kEDvfiKjMa44GYmgBu4n8pq+n
75NJxws6ZkzPs5/QsLT3hvTaL1SNX6PaEW8HabDXO40ccZc4CYvFZVOXMAnKaXzZ
31hj8EvQ5x6hci+SPYyVu6j3ipOxN96VcZqEJ+hWyyuZEMK6Up1o/0lGZFgwa0UD
SIl7RiTFKO6ko+8hYlk1g0DGtEyWDsdso1Bw4zaHwMngM/CwjJVzpK5T2t1fJyEh
lN5MdhcOi0nsiRWdRxOwOlHDLf93qSo87mvseU1MCEXYN1aqTV3VxSm1YU8ZgQVk
sAjpsJqj45enfDa9BmIt
=o8o/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The usual collection of new drivers, non-critical fixes, and updates
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (130 commits)
clk: renesas: mstp: ensure register writes complete
clk: qcom: Do not drop device node twice
clk: mvebu: adjust clock handling for the CP110 system controller
clk: mvebu: Expand mv98dx3236-core-clock support
clk: zte: add i2s clocks for zx296718
clk: sunxi-ng: sun9i-a80: Fix wrong pointer passed to PTR_ERR()
clk: sunxi-ng: select SUNXI_CCU_MULT for sun5i
clk: sunxi-ng: Check kzalloc() for errors and cleanup error path
clk: tegra: Add BPMP clock driver
clk: uniphier: add eMMC clock for LD11 and LD20 SoCs
clk: uniphier: add NAND clock for all UniPhier SoCs
ARM: dts: sun9i: Switch to new clock bindings
clk: sunxi-ng: Add A80 Display Engine CCU
clk: sunxi-ng: Add A80 USB CCU
clk: sunxi-ng: Add A80 CCU
clk: sunxi-ng: Support separately grouped PLL lock status register
clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT
clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag
clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers
clk: qcom: SDHCI enablement on Nexus 5X / 6P
...
A total of 380 patches this time, mostly adding support for more hardware
in the device tree descriptions. There is not much exciting here for 4.11,
but I've tried my best to condense the information from the pull requests
I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now
gets fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already
supported chips
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP architecture
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero,
all based on Allwinner SoCs
http://linux-sunxi.org/LicheePi_Onehttp://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless
https://beagleboard.org/black-wirelesshttps://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam i.Core
http://www.opossom.com/english/index.htmlhttp://www.savageboard.org/http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ulhttp://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas, qcom,
rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic,
eeprom, mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ucQ/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"A total of 380 patches this time, mostly adding support for more
hardware in the device tree descriptions. There is not much exciting
here for 4.11, but I've tried my best to condense the information from
the pull requests I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now gets
fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3:
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box:
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder:
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points:
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already supported
chips:
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP
architecture:
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of
Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero, all based on
Allwinner SoCs:
http://linux-sunxi.org/LicheePi_Onehttp://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform:
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless:
https://beagleboard.org/black-wirelesshttps://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module:
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam
i.Core:
http://www.opossom.com/english/index.htmlhttp://www.savageboard.org/http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ulhttp://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
- Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas,
qcom, rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic, eeprom,
mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (380 commits)
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
ARM: DTS: Fix register map for virt-capable GIC
dt-bindings: arm,gic: Fix binding example for a virt-capable GIC
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
ARM: dts: add the AB8500 sysclk to the device trees
...
When there is no status bit, it is possible for the clock enable/disable
operation to have not completed by the time the driver code resumes
execution. This is due to the fact that write operations are sometimes
queued and delayed internally. Doing a read ensures the write operations
has completed.
Fixes: b6face404f ("ARM: shmobile: r7s72100: add essential clock nodes to dtsi")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
1. Add necessary initial configuration for clocks of display subsystem.
Till now it worked mostly thanks to bootloader.
2. Use macro definitions instead of hard-coded values for pinctrl on Exynos7.
3. Enable USB 3.0 (DWC3) on Exynos7.
-----BEGIN PGP SIGNATURE-----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=02Sx
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Pull "Samsung DeviceTree ARM64 update for v4.11, third round" from Krzysztof Kozłowski:
1. Add necessary initial configuration for clocks of display subsystem.
Till now it worked mostly thanks to bootloader.
2. Use macro definitions instead of hard-coded values for pinctrl on Exynos7.
3. Enable USB 3.0 (DWC3) on Exynos7.
* tag 'samsung-dt64-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (27 commits)
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
clk: samsung: exynos5433: Add data for 250MHz and 278MHz PLL rates
clk: samsung: exynos5433: Add IDs for PHYCLK_MIPIDPHY0_* clocks
arm64: dts: exynos: Add clocks to Exynos5433 LPASS module
arm64: dts: exynos: set LDO7 regulator as always on
arm64: dts: exynos: configure TV path clocks for Ultra HD modes
arm64: dts: exynos: Fix drive strength of sd0_xxx pin definitions
arm64: dts: exynos: Disable pull down for audio pins in Exynos5433 SoCs
arm64: dts: exynos: Add TM2 touchkey node
arm64: dts: exynos: Remove unneeded unit names in Exynos5433 nodes
arm64: dts: exynos: Enable HDMI/TV path on Exynos5433-TM2
arm64: dts: exynos: Add HDMI node to Exynos5433
arm64: dts: exynos: Add DECON_TV node to Exynos5433
arm64: dts: exynos: Fix addresses in node names on Exynos5433
arm64: dts: exynos: Make TM2 and TM2E independent from each other
arm64: dts: exynos: Fix wrong values for ldo23 and ldo25 on TM2/TM2E
...
of_find_node_by_name() drops the reference to a passed device node.
It is not necessary to drop it again, and doing so may result in the
device node being released prematurely.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fixes: ee15faffef ("clk: qcom: common: Add API to register board clocks backwards compatibly")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit:
- makes the GOP_DP (bit 9) gatable clock a child clock of the
SD_MMC_GOP (bit 18) clock, as it should have been. The clock for bit
18 was just named SD_MMC, but since it also covers the GOP block, it
is renamed SD_MMC_GOP.
- makes the MG (bit 5) gatable clock a child clock of the MG_CORE
clock (bit 6)
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The initial implementation in commit e120c17a70 ("clk: mvebu: support
for 98DX3236 SoC") hardcoded a fixed value for the main PLL frequency.
Port code from the Marvell supplied Linux kernel to support different
PLL frequencies and provide clock gating support.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The i2s related clock support is missing from the existing zx296718
clock driver. This patch adds it, so that the upstream ZX I2S driver
can work out.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Fixes: 783ab76ae5 ("clk: sunxi-ng: Add A80 Display Engine CCU")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We get a link error when CCU_MULT is not set with the
newly added driver:
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.17+0x4): undefined reference to `ccu_mult_ops'
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.5+0x4): undefined reference to `ccu_mult_ops'
Fixes: 5e73761786 ("clk: sunxi-ng: Add sun5i CCU driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This kzalloc() could fail. Let's bail out with -ENOMEM here
instead of NULL dereferencing. That silences static checkers. We
should also cleanup on the error path even though this function
returning an error probably means the system won't boot.
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This driver uses the services provided by the BPMP firmware driver to
implement a clock driver based on the MRQ_CLK request. This part of the
BPMP ABI provides a means to enumerate and control clocks and should
allow the driver to work on any chip that supports this ABI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
and making niu (interconnect) clocks critical on rk3288, as
CLK_IGNORE_UNUSED is not enough to keep them running all the time
when more users access particular clock subtrees.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAliRFEMQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgWHMB/0ZQ1p88CmxkN8kiaJBkO8UpmLuRrPivXoH
HiZBN9fvxdR7DcrhQvH8kSt2Ir9h3Rc22TzPWChcwq1io66Bd8BuXkPP/vP9am8J
It0VeERQzyHTLY++DYTsBmQmuaxPRm9cFsxLY5i4vowipjinFj/gDDX6DIg97j2p
r0ytQQhOM47sRhfJSrGFsfXZIa5z5Ty0Qg04ESGmvIllrMUlm9N7+U667qknkYLW
j2T7jWAK2l3RVe9AC7Bf10l7sldzHPHY5MuQ5WiFUWW3OgJyIUKJbD8jythg9i8V
+54LsmX3HkIjS1OiIwECtU1Nv2t8w9RqDRCubzp/Yf+ff+oDL0h3
=VeAF
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull Rockchip clk updates from Heiko Stuebner:
"Non-critical fix for the pclk_edp divider on rk3399, one new
clock-id and making niu (interconnect) clocks critical on
rk3288, as CLK_IGNORE_UNUSED is not enough to keep them running
all the time when more users access particular clock subtrees."
* tag 'v4.11-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: rk3288: make all niu clocks critical
clk: rockchip: use rk3288 vip_out clock ids
clk: rockchip: add rk3288 vip_out clock id
clk: rockchip: fix the incorrect pclk_edp div width for RK3399
Add clock for the Cadence eMMC controller on LD11/LD20.
For the other SoCs, the clock for the eMMC controller is included
in the MIO/SD control block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add clock line for the Denali NAND controller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Support for one new SoC, the V3s
- Convertion of two old SoCs to the new framework, the old sun5i family
and the A80
- A bunch of fixes
-----BEGIN PGP SIGNATURE-----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=Jkg2
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Pull Allwinner clock updates from Maxime Ripard:
- Support for one new SoC, the V3s
- Conversion of two old SoCs to the new framework, the old sun5i family
and the A80
- A bunch of fixes
* tag 'sunxi-clk-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (25 commits)
ARM: dts: sun9i: Switch to new clock bindings
clk: sunxi-ng: Add A80 Display Engine CCU
clk: sunxi-ng: Add A80 USB CCU
clk: sunxi-ng: Add A80 CCU
clk: sunxi-ng: Support separately grouped PLL lock status register
clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT
clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag
clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers
clk: sunxi-ng: a33: Set CLK_SET_RATE_PARENT for the GPU
clk: sunxi-ng: Call divider_round_rate if we only have a single parent
ARM: gr8: Convert to CCU
ARM: sun5i: Convert to CCU
clk: sunxi-ng: Add sun5i CCU driver
clk: sunxi-ng: Implement global pre-divider
clk: sunxi-ng: Implement multiplier maximum
clk: sunxi-ng: mult: Fix minimum in round rate
clk: sunxi-ng: Implement factors offsets
clk: sunxi-ng: multiplier: Add fractional support
clk: sunxi-ng: add support for V3s CCU
dt-bindings: add device binding for the CCU of Allwinner V3s
...
This patch updates dev_pm_opp_find_freq_*() routines to get a reference
to the OPPs returned by them.
Also updates the users of dev_pm_opp_find_freq_*() routines to call
dev_pm_opp_put() after they are done using the OPPs.
As it is guaranteed the that OPPs wouldn't get freed while being used,
the RCU read side locking present with the users isn't required anymore.
Drop it as well.
This patch also updates all users of devfreq_recommended_opp() which was
returning an OPP received from the OPP core.
Note that some of the OPP core routines have gained
rcu_read_{lock|unlock}() calls, as those still use RCU specific APIs
within them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> [Devfreq]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the A80 SoC, Allwinner grouped and moved some subsystem specific
clock controls to a separate address space, and possibly separate
hardware block.
One such subsystem is the display engine. The main clock control unit
now only has 1 set of bus gate, dram gate, module clock, and reset
control for the entire display subsystem. These feed into a secondary
clock control unit, which has controls for each individual module
of the display pipeline. This block is not documented in the user
manual. Allwinner's kernel was used as the reference.
Add support for the display engine clock controls found on the A80.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the USB clock controls found on the A80.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the main clock unit found in the A80. Some clocks were
not documented in the released user manual, but were found in the
official kernel from Allwinner. These include controls for the I2S,
SPDIF, SATA, and eDP blocks.
Note that on the A80, some subsystems have separate clock controllers
downstream of the main clock unit. These include the MMC, USB, and
display engine subsystems.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Allwinner A80 SoC, the PLL lock status indicators are grouped
together in a separate register, as opposed to being scattered in each
PLL's configuration register.
Add a flag to support this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
If the CLK_SET_RATE_PARENT flag is set, we want to try getting the
closest parent rate.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds support for the CLK_SET_RATE_NO_REPARENT flag to the
mux determine_rate helper, based on examples from clk-composite and
clk-mux.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The determine_rate helper used ccu_mux_helper_adjust_parent_for_prediv()
to adjust the parent_rate to account for pre-dividers, but then passed
the pristine parent clock rate from clk_hw_get_rate() to the round()
callback, thereby ignoring the pre-divider adjustment. In addition,
it was saving the adjusted parent rate back into struct
clk_rate_request.
This patch fixes this by saving the pristine parent clock rate, and
adding a copy that is adjusted and passed to the round() callback.
The pristine copy, if it is the best solution, would be saved back
to struct clk_rate_request.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add missing clock branch to enable onboard storage
for msm899(2/4).
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Use CLK_IS_CRITICAL to handle critical clocks,
- Add Reset Control Support for R-Car Gen2 and Gen3, and RZ/G1,
- Add IIC-DVFS clocks for R-Car H3 and M3-W,
- Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WluB
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Use CLK_IS_CRITICAL to handle critical clocks,
- Add Reset Control Support for R-Car Gen2 and Gen3, and RZ/G1,
- Add IIC-DVFS clocks for R-Car H3 and M3-W,
- Minor cleanups.
* tag 'clk-renesas-for-v4.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add IIC-DVFS clock
clk: renesas: r8a7795: Add IIC-DVFS clock
clk: renesas: cpg-mssr: Add support for reset control
clk: renesas: cpg-mssr: Rename cpg_mssr_priv.mstp_lock
clk: renesas: cpg-mssr: Document suitability for RZ/G1
dt-bindings: clock: renesas: cpg-mssr: Document reset control support
clk: renesas: mstp: Reformat cpg_mstp_clock_register() for git diff
clk: renesas: mstp: Make INTC-SYS a critical clock
clk: renesas: cpg-mssr: Migrate to CLK_IS_CRITICAL
CLKID_ETH is define in the dt-bindings but has not be commented out in the
clock driver. Just do it now.
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The 98DX3236, 98DX3336, 98DX4521 and variants have a different TCLK from
the Armada XP (200MHz vs 250MHz). The CPU core clock is fixed at 800MHz.
The clock gating options are a subset of those on the Armada XP.
The core clock divider is different to the Armada XP also.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These functions are referencing s3c...._clk_regs[], which are marked as
__initdata. When compiling with CONFIG_DEBUG_SECTION_MISMATCH=y, this
produces warnings like
WARNING: vmlinux.o(.text+0x198350):
Section mismatch in reference from the function s3c2410_clk_sleep_init()
to the (unknown reference) .init.data:(unknown)
Mark the s3c...._clk_sleep_init() functions as __init in
order to fix this.
Fixes: ca2e90ac18 ("clk: samsung: add clock controller driver for s3c2412")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Some PLLs might be disabled by default after turning off and then on
a power domain which they belongs to. To avoid configuring a disabled
PLL, add proper code for handling PLL enable/disable.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch fixes simple typos in Exynos5433 clocks driver. The SoC name
was referred a few times as '5443' instead of '5433'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Default clock configuration applied by the bootloader for TM2 and TM2e
boards includes 250MHz and 278MHz rate for DISP PLL clock. To ensure
such configuration for those boards with 'assigned-clock-*' properties,
parameters for those two additional rates are needed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add missing identifiers for phyclk_mipidphy0_bitclkdiv8_phy and
phyclk_mipidphy0_rxclkesc0_phy clocks. Access to those clocks is needed
to setup initial clock configuration for display subsystem in device tree
in order to avoid dependency on the configuration left by the bootloader.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
In order to achieve all the rates asked by the GPU, we might need to change
the parent frequency.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The divider_get_val function that is used in our determine_rate callback
doesn't try to change the parent rate at all, while clk_divider_bestdiv,
used in divider_round_rate, does.
If we have a single parent, call divider_round_rate.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Add optional support for the Reset Control feature of the Renesas Clock
Pulse Generator / Module Standby and Software Reset module on R-Car
Gen2, R-Car Gen3, and RZ/G1 SoCs.
This allows to reset SoC devices using the Reset Controller API.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The spinlock is used to protect Read-Modify-Write register accesses,
which won't be limited to SMSTPCR register accesses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The Renesas CPG/MSSR driver is already in active use for RZ/G1 since
commits c0b2d75d2a ("clk: renesas: cpg-mssr: Add R8A7743 support")
and 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
As the function header of cpg_mstp_clock_register() is split in an
unusual way, "git diff" gets confused when changes to the body of
the function are made, and attributes them to the wrong function.
Reformat the function header to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The BayTrail and CherryTrail platforms provide platform clocks
through their Power Management Controller (PMC).
The SoC supports up to 6 clocks (PMC_PLT_CLK[0..5]) with a
frequency of either 19.2 MHz (PLL) or 25 MHz (XTAL) for BayTrail
and a frequency of 19.2 MHz (XTAL) for CherryTrail. These clocks
are available for general system use, where appropriate, and each
have Control & Frequency register fields associated with them.
Port from legacy by Pierre Bossart, integration in clock framework
by Irina Tirdea
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix Makefile for x86 support, dependency on CONFIG_COMMON_CLK
was not explicit
Fixes: 701190fd74 ('clk: x86: add support for Lynxpoint LPSS clocks')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In clock driver initialize phase the spinlock is missed to assignment
to struct clkgate_separated, finally there have no locking to protect
exclusive accessing for clock registers.
This bug introduces the console has no output after enable coresight
driver on 96boards Hikey; this is because console using UART3, which
has shared the same register with coresight clock enabling bit. After
applied this patch it can assign lock properly to protect exclusive
accessing, and console can work well after enabled coresight modules.
Fixes: 0aa0c95f74 ("clk: hisilicon: add common clock support")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-ux500:
clk: ux500: Convert ABx500 clocks to use OF probing
clk: ux500: Add device tree bindings for ABx500 clocks
clk: ux500: move AB8500 sysclk over to PRCMU clk driver
These clocks have been broken for a long time unfortunately, a
hurdle of misc problems made them stop working at some point
breaking USB and audio on Ux500.
The platform as such and all "regular" clocks are migrated to
OF/device tree, so let's migrate also this driver.
With this patch and the corresponding DTS fixes, and a bunch
of probe deferral fixes, audio starts working again on Ux500.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The AB8500 sysclk is just another PRCMU-controlled clock, there
is no reason why it should be in the ABx500-controlled part of
the clock implementation. Doing this and the corresponding device
tree changes makes USB work on the Ux500 again.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The MT8135 is a 32-bit SoC, so only propose it on ARM architecture,
not ARM64.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 234d511d8c ("clk: mediatek: Add hardware dependency")
Cc: Andreas Färber <afaerber@suse.de>
Acked-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If I say "no" to "Clock driver for Mediatek MT2701", I don't want to
be asked individually about each sub-driver. No means no.
Additionally, this driver shouldn't be proposed at all on non-mediatek
builds, unless build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: e986211827 ("clk: mediatek: Add MT2701 clock support")
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: James Liao <jamesjj.liao@mediatek.com>
Cc: Shunli Wang <shunli.wang@mediatek.com>
Cc: Erin Lo <erin.lo@mediatek.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the divider selection logic blindly divides the parent_rate
by the clk rate and gives the divider value for the divider clocks
which do not have the CLK_SET_RATE_PARENT flag set. Add the clk divider
table parsing to get the closest divider available in the table
provided via Device tree.
The code is pretty much taken from: drivers/clk/clk-divider.c.
and used here to fix up the best divider selection logic.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Once a gdsc is brought in and out of HW control, there is a
power down and up cycle which can take upto 1us. Polling on
the gdsc status immediately after the hw control enable/disable
can mislead software/firmware to belive the gdsc is already either on
or off, while its yet to complete the power cycle.
To avoid this add a 1us delay post a enable/disable of HW control
mode.
Also after the HW control mode is disabled, poll on the status to
check gdsc status reflects its 'on' before force disabling it
in software.
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: 904bb4f5c7 ("clk: qcom: gdsc: Add support for gdscs with HW control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
During meson8b clock probe, clk81 register address is fixed twice.
First using the meson8b_clk_gates array, then by directly changing
meson8b_clk81 register.
As a result meson8b_clk81.reg = HHI_MPEG_CLK_CNTL + clk_base + clk_base.
Fixed by just removing the second fixup.
Fixes: e31a1900c1 ("meson: clk: Add support for clock gates")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch enables clocks for STM32F746 boards.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Do not let the entire probe function fail even if some clocks fail
to register. Let's continue with succeeded clocks. This will give
the system more chances to boot and allow us to investigate the
cause of the failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The HHI_SAR_CLK_CNTL contains three SAR ADC specific clocks:
- a mux clock to choose between different ADC reference clocks (this is
2-bit wide, but the datasheet only lists the parents for the first
bit)
- a divider for the input/reference clock
- a gate which enables the ADC clock
Additionally this exposes the ADC core clock (CLKID_SAR_ADC) and
CLKID_SANA (which seems to enable the analog inputs, but unfortunately
there is no documentation for this - we just mimic what the vendor
driver does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Allwinner A10s, A13, R8 and NextThing GR8 are all based on the same
silicon, and all share the same clocks.
However, they're not packaged in the same way, and therefore not all the
controllers are actually available on all these SoCs.
Introduce a clock controller driver for all these SoCs with different
compatibles to take that into account.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clocks have a global pre-divider that applies to all their parents.
Since it might also apply to clocks that have a single parent, this is
merged in the ccu_common structure, unlike the other pre-divider settings
that are tied to a specific index, and thus a specific parent.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some multipliers have a maximum rate that is lower than what the register
width allows to. Add a field in the multiplier structure to allow CCU
driver to set that maximum.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The previous code was always taking 1 as the minimum in it's round_rate
function, ignoring entirely what was set as minimum in the clock
definition.
Make sure that's not the case anymore.
Fixes: 2beaa601c8 ("clk: sunxi-ng: Implement minimum for multipliers")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The factors we've seen so far all had an offset of one. However, on the
earlier Allwinner SoCs, some factors could have no offset at all, meaning
that the value computed to reach the rate we want to use was the one we had
to program in the registers.
Implement an additional field for the factors that can have such an offset
(linears, not based on a power of two) to specify that offset.
This offset is not linked to the extremums that can be specified in those
structures too. The minimum and maximum are representing the range of
values we can use to try to compute the best rate. The offset comes later
on when we want to set the best value in the registers.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clocks on the earlier SoCs such as the video PLLs are multipliers with
fractional settings.
Support those cases.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
INTC-SYS is the module clock for the GIC. Accessing the GIC while it is
disabled causes:
Unhandled fault: asynchronous external abort (0x1211) at 0x00000000
Currently, the GIC-400 driver cannot enable its module clock for several
reasons:
- It does not use a platform device, so Runtime PM is not an option,
- gic_of_init() runs before any clocks are registered, so it cannot
enable the clock explicitly,
- gic_of_init() cannot return -EPROBE_DEFER, as IRQCHIP_DECLARE()
doesn't support deferred probing.
Hence we have to keep on relying on the boot loader for enabling the
module clock.
To prevent the module clock from being disabled when the CCF core thinks
it is unused, and thus causing a system lock-up, add a check to the MSTP
clock driver and enable CLK_IS_CRITICAL. This will make sure the module
clock is never disabled.
This is a hard dependency for describing the INTC-SYS clock in DT on
R-Mobile APE6 and R-Car Gen2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
When the Renesas CPG/MSSR driver was introduced, it was anticipated that
critical clocks would be handled through a new CLK_ENABLE_HAND_OFF flag
soon. However, CLK_ENABLE_HAND_OFF never made it upstream.
Instead, commit 32b9b10961 ("clk: Allow clocks to be marked as
CRITICAL") introduced CLK_IS_CRITICAL, a flag with slightly differing
semantics. Still, it can be used to prevent e.g. the GIC module clock
from being turned off, until the GIC-400 driver has full support for
Runtime PM.
Hence migrate the Renesas CPG/MSSR driver from CLK_ENABLE_HAND_OFF to
CLK_IS_CRITICAL.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
NIU clocks are related to the interconnect and it's important to other blocks.
Since we don't have a driver to handle it, we should always enable it to avoid
casually close.
Make all of them critical,so that we don't have to each clock on its own
once things break.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
[dropped the matching CLK_IGNORE_UNUSED flags]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reference the newly added vip clock-ids in the clock-tree.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
caused some of these clocks to turn off when they were always left
on before.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0KLk
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for Samsung Exynos524x SoCs where recent IOMMU patches have
caused some of these clocks to turn off when they were always left on
before"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk/samsung: exynos542x: mark some clocks as critical
Add the OCOTP so that this hardware block can be used.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This proved incredibly useful during debugging of the DSI driver, to
see if our clocks were running at rate we requested. Let's leave it
here for the next person interacting with clocks on the platform (and
so that hopefully we can just hook it up to debugfs some day).
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The DSI pixel clocks are muxed from clocks generated in the analog phy
by the DSI driver. In order to set them as parents, we need to do the
same name lookup dance on them as we do for our root oscillator.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Our core PLLs are intended to be configured once and left alone. With
the SET_RATE_PARENT, asking to set the PLLD_DSI1 clock rate would
change PLLD just to get closer to the requested DSI clock, thus
changing PLLD_PER, the UART and ethernet PHY clock rates downstream of
it, and breaking ethernet.
We *do* want PLLH to change so that PLLH_AUX can be exactly the value
we want, though. Thus, we need to have a per-divider policy of
whether to pass rate changes up.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These
chips have two clock inputs, XTAL or CLK, which are muxed into single
PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip
while the 5P49V5923 requires external XTAL.
The PLL feeds two fractional dividers. Each fractional divider feeds
output mux, which allows selecting between clock from the fractional
divider itself or from output mux on output N-1. In case of output
mux 0, the output N-1 is instead connected to the output from the mux
feeding the PLL.
The driver thus far supports only the 5P49V5923 and 5P49V5933, while
it should be easily extensible to the whole 5P49V59xx family of chips
as they are all pretty similar.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
controlled through the General Register Files, support for the rk3328
clock-controller (including a new pll-type) and the usual clock ids and
some fixes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlh+vFMQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgf7TCACncJmYlvYp+aZEgBlEcyCTulHNSyRZHVPd
c4zBsgZmgxqmgrxe8YsW6DcfPP96MtL/C/fIupxTphxxfAS5HQx2KCeVpOrfffk7
lJ1CPyCP5GdjaZ98hKVuMpKVkQu1u26DTNWSy62hbSQQndbpP0NbGsIJJUFia1vm
JX0POVYt0xSo6GnbVRcKN/5b9k0HJNG9aejL8u/uA3+yr8diiKzYrtnaFzai5kvE
3LgXIDGPUZVfwZ2vrJfDCYqNlij/tF2yLIhEDDoMSl00WolJfmnMKOg1Lt0DzuMz
OQY6ZIexTV1CCV+9BjXMVCLth7DH7K3EztQsvyJtr90wrfYs+4Vd
=4WOJ
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull Rockchip clk updates from Heiko Stuebner:
A new clock-type for the 1-2 muxes per soc that are for whatever reason
controlled through the General Register Files, support for the rk3328
clock-controller (including a new pll-type) and the usual clock ids and
some fixes.
* tag 'v4.11-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: clk: add rockchip,grf property for RK3399
clk: rockchip: use clock ids for memory controller parts on rk3066/rk3188
clk: rockchip: use rk3288 isp_in clock ids
clk: rockchip: add clock ids for memory controller parts on rk3066/rk3188
clk: rockchip: add rk3288 isp_in clock ids
clk: rockchip: Remove useless init of "grf" to -EPROBE_DEFER
clk: rockchip: add clock controller for rk3328
dt-bindings: add bindings for rk3328 clock controller
clk: rockchip: add dt-binding header for rk3328
clk: rockchip: add new pll-type for rk3328
clk: rockchip: describe aclk_vcodec using the new muxgrf type on rk3288
clk: rockchip: add a clock-type for muxes based in the grf
- addition of the CPU clock configuration data for Exynos4412
Prime SoC variant,
- removal of driver for deprecated Exynos4415 SoC,
- switching from the syscore to regular system sleep PM ops
in the audio subsystem clocks controller driver,
- updates of the definitions of some "Network On Chip" related
clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mSQz
-----END PGP SIGNATURE-----
Merge tag 'clk-v4.11-samsung' of git://linuxtv.org/snawrocki/samsung into clk-next
Pull Samsung clk updates from Sylwester Nawrocki:
- addition of the CPU clock configuration data for Exynos4412
Prime SoC variant,
- removal of driver for deprecated Exynos4415 SoC,
- switching from the syscore to regular system sleep PM ops
in the audio subsystem clocks controller driver,
- updates of the definitions of some "Network On Chip" related
clocks.
* tag 'clk-v4.11-samsung' of git://linuxtv.org/snawrocki/samsung:
clk: samsung: Remove Exynos4415 driver (SoC not supported anymore)
clk: samsung: exynos-audss: Replace syscore PM with platform device PM
clk: samsung: exynos5433: Set NoC (Network On Chip) clocks as critical
clk: samsung: Add CPU clk configuration data for Exynos4412 Prime
The LDB mux/gate layout has been fixed on QuadPlus, so there is no need
to restrict the LDB mux changes on this hardware, as the erratum
preventing this from working properly is gone.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
V3s has a similar but cut-down CCU to H3. Some muxes, especially clocks
about CSI, are different, which makes it to need a new CCU driver.
Add such a new driver for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Export HDMI clock from internal to dt-bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The range of the pclk_edp_div_con is [13:8] and 6 bits, not 5.
Reported-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Tested-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The audio DAI needs to set the clock rates of the ac-dig clock.
To make it possible, the parent PLL audio clock rates should
also be changed. This is possible via "CLK_SET_RATE_PARENT" flag.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
1. Fixes for initial audio clocks configuration.
2. Enable sound on Odroid-X board.
3. Enable DMA for UART modules on Exynos5 SoCs.
4. Add CPU OPPs for Exynos4412 Prime (newer version of Exynos4412). This pulls
necessary change in the clocks.
5. Remove Exynos4212. We do not have any mainline boards with it. This will
simplify few bits later.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYeOsYAAoJEME3ZuaGi4PXuSMP/RFjn4liQ4qG/uE5j6+7HDSF
PC/1yBYyo0xzg8oaEJVz7Ay6ydqNqBAMhPfdJzWk1lzN+zQc2MwLynH1fNNJTWSY
6YtBhNzx5sgs1IRtqG8RvSpj67OlE6i98YJL64j4VjNdhcTrRBPSbm2TDeu82uzh
VY3RDsXkTeWNwiHRuDXRqZ3VLfZ/xGjuT7Ym0cEMjPeuETNHs6jYVfi5e1d1c631
Ln2MJj0dpLbf+eUqkvLjv45LIHr6DmQHhuHlfwNu9iY6EmDtS+m9BKBxMvGrWzSp
5fy/3MpQo6+DD0GocnbsQpqylKmI5sXX9ly0A4F2ZWMRkoULVHv/5UrP7V9puHyO
Rd6i9RrpPDzAm81KRorFbwJnl2uJlomR5yWSISWQ51p6HXP1mFi+78YacUgCgNM0
TDCXhuGp1ZbJmBtq1Eae3C6Ku9GEtq9WLNkphWzeqUc4miZRwQ9NGBtZhbbgoFOl
XvANJAfVcS6PDJyadKlD/bktz8cyNO+H3jMPzlFRqaGW/E0yX8BbG01kjJhmR2dZ
qAMJtWT55PPNBss/ml67qezEYBXw9xwyo9d0vPnTWE0XvCL/p++Q+BEojKB8zYuE
4NJrj01CjZmpa8Ej3zpi6MLbVaKto5TjNTe981jzyAUpGlt2fiAuGmn85lTP2a0c
4LKCFLMZ8HGDMRL1WTkl
=w/rg
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree update for v4.11:
1. Fixes for initial audio clocks configuration.
2. Enable sound on Odroid-X board.
3. Enable DMA for UART modules on Exynos5 SoCs.
4. Add CPU OPPs for Exynos4412 Prime (newer version of Exynos4412). This pulls
necessary change in the clocks.
5. Remove Exynos4212. We do not have any mainline boards with it. This will
simplify few bits later.
* tag 'samsung-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: remove Exynos4212 support (dead code)
ARM: dts: exynos: Add CPU OPPs for Exynos4412 Prime
clk: samsung: Add CPU clk configuration data for Exynos4412 Prime
ARM: dts: exynos: Enable DMA support for UART modules on Exynos5 SoCs
ARM: dts: exynos: Cleanup Odroid-X2 and enable sound on Odroid-X
ARM: dts: exynos: Fix initial audio clocks configuration on Exynos4 boards
ARM: dts: exynos: Correct clocks for Exynos4 I2S module
Signed-off-by: Olof Johansson <olof@lixom.net>
Support for Exynos4415 is going away because there are no internal nor
external users.
Since commit 46dcf0ff0d ("ARM: dts: exynos: Remove exynos4415.dtsi"),
the platform cannot be instantiated so remove also the drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add the newly added clock ids to the clock entries of the rk3066/rk3188
clock driver. We won't be needing them in the kernel for a bit yet
but as they're used in the new u-boot ddr setup code/dts we should make
sure the clock ids stay identical and do not differ.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reference the newly added isp clock-ids in the clock-tree.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The failure path in the newly added function tries to free an
uninitialized pointer:
drivers/clk/clk-stm32f4.c: In function 'stm32f4_rcc_init':
drivers/clk/clk-stm32f4.c:1106:4: error: 'gate' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I'm adding an initialization to NULL here to make the kfree()
succeed, and I'm also rearranging the cleanup so that the
same kfree() is used for any error path, making the function
slightly more robust against newly introduced bugs in the
error handling.
Fixes: daf2d117cb ("clk: stm32f4: Add lcd-tft clock")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The CDCE925 is a member of the CDCE(L)9xx programmable clock generator
family. There are also CDCE913, CDCE937, CDCE949 which have different
number of PLLs and outputs.
The clk-cdce925 driver supports only CDCE925 in the family. This adds
support for the CDCE913, CDCE937, CDCE949, too.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add definition of EBI2 clock used by MDM9615 NAND controller.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Zoran Markovic <zmarkovic@sierrawireless.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[sboyd@codeaurora.org: ebi2_clk halt bit is 24 not 23]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This include was needed to suppress build error when this driver
was initially merged because <linux/regmap.h> did not include
<linux/delay.h> at that time. (developers' headache across
sub-systems)
The root cause has been fixed by commit adf08d481b ("regmap:
include <linux/delay.h> from include/linux/regmap.h"), so this
line can be dropped now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit adjusts the list of possible "Sample At Reset" values that
define the CPU clock frequency of the AP806 (part of Marvell Armada
7K/8K) to the values that have been validated with the production
chip. Earlier values were preliminary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add clock drivers for hi3660 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[sboyd@codeaurora.org: Simplify probe with function pointer]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some parent clocks of the Exynos542x clock blocks, which have separate
power domains (like DISP, MFC, MSC, GSC, FSYS and G2D) must be always
enabled to access any register related to power management unit or devices
connected to it. For the time being, until a proper solution based on
runtime PM is applied, mark those clocks as critical (instead of ignore
unused or even no flags) to prevent disabling them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> [Exynos5800 Peach Pi Chromebook]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
EPROBE_DEFER is not an error, hence printing an error message like
clk: couldn't get clock 0 for /soc/display@feb00000
may confuse the user.
Suppress error messages in case of probe deferral to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently we add the virtual cpufreq device unconditionally even when
the SCPI DVFS clock provider node is disabled. This will cause cpufreq
driver to throw errors when it gets initailised on boot/modprobe and
also when the CPUs are hot-plugged back in.
This patch fixes the issue by adding the virtual cpufreq device only if
the SCPI DVFS clock provider is available and registered.
Fixes: 9490f01e24 ("clk: scpi: add support for cpufreq virtual device")
Reported-by: Michał Zegan <webczat_200@poczta.onet.pl>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Michał Zegan <webczat_200@poczta.onet.pl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support to use reset control framework for resetting MSS
with hexagon v56 1.5.0.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The audio related clock support is missing from the existing zx296718
clock driver. Let's add it, so that the upstream ZX SPDIF driver can
work for HDMI audio support.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[sboyd@codeaurora.org: Staticize some more structures]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Instead of using panic, we should give an error message and return error
code when of_clk_add_hw_provider() call fails.
Since we have error prompt for failures, the "init over" pr_info output
isn't really necessary but becomes a debug noise. So let's clean it up
along the way.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The delay here is not in atomic context and does not seem critical with
respect to precision, but usleep_range(min,max) with min==max results in
giving the timer subsystem no room to optimize uncritical delays. Fix
this by setting the range to 2000,3000 us.
Fixes: commit f05259a6ff ("clk: wm831x: Add initial WM831x clock driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On vf610, PLL1 and PLL2 have registers to configure fractional part of
frequency multiplier.
This patch adds support for these registers.
This fixes "fast system clock" issue on boards where bootloader sets
fractional multiplier for PLL1.
Suggested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
CC: Chris Healy <cphealy@gmail.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
turn all the clks on and another fix for stm32f4 SoCs where we have multiple
drivers attaching to the same DT node.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5ciP
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One fix for a broken driver on Renesas RZ/A1 SoCs with bootloaders
that don't turn all the clks on and another fix for stm32f4 SoCs where
we have multiple drivers attaching to the same DT node"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: stm32f4: Use CLK_OF_DECLARE_DRIVER initialization method
clk: renesas: mstp: Support 8-bit registers for r7s72100
When we used to defer setting the "grf" member to
rockchip_clk_get_grf() it was important to init the "grf" member to an
error value in rockchip_clk_init(). With recent changes, we now set
"grf" right in rockchip_clk_init() (two lines below the place where we
initted it). That makes the old init useless. Get rid of it.
Fixes: 6f339dc271 ("clk: rockchip: lookup General Register Files in rockchip_clk_init")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the clock tree definition for the new rk3328 SoC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As the SPDIF was rarely documented on the earlier Allwinner SoCs
it was assumed that it had a similar clock register to the one
described in the H3 User Manual.
However this is not the case and it looks to shares the same setup
as the I2S clock registers.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPUX clock on A33, which is for the Cortex-A7 cores, is designed to
be changeable by changing the rate of PLL_CPUX.
Add CLK_SET_RATE_PARENT flag to this clock.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When adjusting PLL_CPUX on A33, the PLL is temporarily driven too high,
and the system hangs.
Add a notifier to avoid this situation by temporarily switching to a
known stable 24 MHz oscillator.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When adjusting PLL_CPUX on H3, the PLL is temporarily driven
too high, and the system becomes unstable (oopses or hangs).
Add a notifier to avoid this situation by temporarily switching
to a known stable 24 MHz oscillator.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Tested-by: Lutz Sammer <johns98@gmx.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The rk3328's pll and clock are similar with rk3036's,
it different with pll_mode_mask, the rk3328 soc
pll mode only one bit(rk3036 soc have two bits)
so these should be independent and separate from
the series of rk3328s.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the newly introduced clk type for muxes in the grf we now can
describe some missing clocks, like the aclk_vcodec that selects between
aclk_vdpu and aclk_vepu based on a bit set in the general register files.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip socs often have some tiny number of muxes not controlled from
the core clock controller but through bits set in the general register
files. Add a clock-type that can control these as well, so that we
don't need to work around them being absent.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Exynos AUDSS clock driver has been already converted to platform driver,
so remove the dependency on the syscore ops - the last remaining
non-platform driver feature. Platform device's system sleep PM provides
all needed infrastructure for replacing syscore-based PM, so do it now.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The ACLK_BUS0/1/2 are used for NoC (Network on Chip). If NoC's clocks are
disabled, the system halt happens. Following clocks must be always enabled:
- CLK_ACLK_BUS0_400 : NoC's bus clock for PERIC/PERIS/FSYS/MSCL,
- CLK_ACLK_BUS1_400 : NoC's bus clock for MFC/HEVC/G3D,
- CLK_ACLK_BUS2_400 : NoC's bus clock for GSCL/DISP/G2D/CAM0/CAM1/ISP.
This patch also adds the CLK_SET_RATE_PARENT flag to the CLK_SCLK_JPEG_MSCL
because this clock should be used for bus frequency scaling. This clock need
to be changed on the fly with CLK_SET_RATE_PARENT flag.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add cpu clock configuration data for Exynos4412 Prime SoC
(it supports additional PLL rates & CPU frequencies).
Based on Hardkernel's kernel for ODROID-X2/U2/U3 boards.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The current driver code gives the crash or gets hang while switching
the CPU frequency some time. The APSS CPU Clock divider is not glitch
free so it the APPS clock need to be switched for stable clock during
the change.
This patch adds the frequency change notifier for APSS CPU clock. It
changes the parent of this clock to stable PLL FEPLL500 for
PRE_RATE_CHANGE event. This event will be generated before actual
clock set operations. The clock set operation will again change its
corresponding parent by getting the same from frequency table.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
[sboyd@codeaurora.org: Indent less in probe]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Clock and reset controller use same compatible strings (same IP).
Since commit 989eafd0b6 ("clk: core: Avoid double initialization of
clocks") the OF core flags clock controllers registered with the
CLK_OF_DECLARE() macro as OF_POPULATED, so platform devices with the same
compatible string will not be registered.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RZ/A1 is different than the other Renesas SOCs because the MSTP
registers are 8-bit instead of 32-bit and if you try writing values as
32-bit nothing happens...meaning this driver never worked for r7s72100.
Fixes: b6face404f ("ARM: shmobile: r7s72100: add essential clock nodes to dtsi")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In the stm32f469 soc, the 48Mhz clock could be derived from pll-q or
from pll-sai-p.
The SDIO clock could be also derived from 48Mhz or from sys clock.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch introduces SAI clocks for stm32f4 socs.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch introduces I2S clock for stm32f4 soc.
The I2S clock could be derived from an external clock or from pll-i2s
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch introduces lcd-tft clock for stm32f4 soc.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds post dividers of I2S & SAI PLLs.
These dividers are managed by a dedicated register (RCC_DCKCFGR).
The PLL should be off before a set rate.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch introduces PLL_I2S and PLL_SAI.
Vco clock of these PLLs can be modify by DT (only n multiplicator,
m divider is still fixed by the boot-loader).
Each PLL has 3 dividers. PLL should be off when we modify the rate.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Mark stm32f4_pll_div_ops static]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds all RPM based clocks for msm8974, except cxo and
gfx3d_clk_src.
Tested-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The APSS CPU clock does not contain all the frequencies in its
frequency table so this patch adds the same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
1. The parent for sdcc clock is sdccpll.
2. The frequency value was wrong so modified the same.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver does not have the node for
PCNOC so this patch adds and registers the PCNOC clock nodes.
This PCNOC clock is critical and should not be turned off so
setting CRITICAL flag also.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver does not have support for all
the frequency supported by APSS CPU. APSS CPU frequency is
provided with APSS CPU PLL divider which divides down the VCO
frequency. This divider is nonlinear and specific to IPQ4019
so the standard divider code cannot be used for this.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current ipq4019 clock driver registered the PLL clocks and
dividers as fixed clock. These fixed clock needs to be removed
from driver probe function and same need to be registered with
clock framework. These PLL clocks should be programmed only
once and the same are being programmed already by the boot
loader so the set rate operation is not required for these
clocks. Only the rate can be calculated by clock operations
in clock driver file so this patch adds the same.
The PLL takes the reference clock from XO and generates the
intermediate VCO frequency. This VCO frequency will be divided
down by different PLL internal dividers. Some of the PLL
internal dividers are fixed while other are programmable.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull ARM updates from Russell King:
- an update for clkdev registration error detection to simplify users
- add cpu capacity parsing from DT
- support for larger cachelines found on UniPhier caches
- documentation for udelay constants
- properly tag assembly function declarations
- remove unnecessary indirection of asm/mach-types.h
- switch to syscall table based generation to simplify future additions
of system calls, along with correpsonding commit for pkey syscalls
- remove redundant sa1101 header file
- RONX protect modules when they're in the vmalloc region
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: mm: allow set_memory_*() to be used on the vmalloc region
ARM: mm: fix set_memory_*() bounds checks
ARM: 8631/1: clkdev: Detect errors in clk_hw_register_clkdev() for mass registration
ARM: 8629/1: vfp: properly tag assembly function declarations in C code
ARM: 8622/3: add sysfs cpu_capacity attribute
ARM: 8621/3: parse cpu capacity-dmips-mhz from DT
ARM: 8623/1: mm: add ARM_L1_CACHE_SHIFT_7 for UniPhier outer cache
ARM: Update mach-types
ARM: sa1100: remove SA-1101 header file
ARM: 8619/1: udelay: document the various constants
ARM: wire up new pkey syscalls
ARM: convert to generated system call tables
ARM: remove indirection of asm/mach-types.h
These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2,
this is an new variant of the the DRA72x/DRA74x automotive
infotainment chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7
based microcontroller we support, related to the smaller
STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile,
see http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to
removing support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the
memory controller using 'perf'
Conflicts:
arch/arm/mach-shmobile/setup-rcar-gen2.c: rcar_gen2_clocks_init()
is gone, calling of_clk_init(NULL) is sufficient now.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BF6Y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2, this
is an new variant of the the DRA72x/DRA74x automotive infotainment
chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7 based
microcontroller we support, related to the smaller STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile, see
http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to removing
support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the memory
controller using 'perf'"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (95 commits)
ARM: davinci: da830-evm: use gpio descriptor for mmc pins
ARM: davinci: da850-evm: use gpio descriptor for mmc pins
ARM: davinci: hawk: use gpio descriptor for mmc pins
ARM: ARTPEC-6: add select MFD_SYSCON to MACH_ARTPEC6
ARM: davinci: da8xx: Fix ohci device name
ARM: oxnas: Add OX820 config and makefile entry
ARM: oxnas: Add OX820 SMP support
ARM: davinci: PM: fix build when da850 not compiled in
ARM: orion5x: remove legacy support of ls-chl
ARM: integrator: drop EBI access use syscon
ARM: BCM5301X: Add back handler ignoring external imprecise aborts
ARM: davinci: PM: support da8xx DT platforms
ARM: davinci: PM: cleanup: remove references to pdata
ARM: davinci: PM: rework init, remove platform device
ARM: Kconfig: Introduce MACH_STM32F746 flag
ARM: mach-stm32: Add a new SOC - STM32F746
ARM: shmobile: document SK-RZG1E board
ARM: shmobile: r8a7745: basic SoC support
ARM: imx: mach-imx6ul: add imx6ull support
ARM: zynq: Reserve correct amount of non-DMA RAM
...
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of
the machines that are still normally used with classic board files.
One tegra fix is important for new bootloader versions, but the
bug has been around for a while without anyone noticing.
The other changes are mostly cosmetic.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i2l2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of the
machines that are still normally used with classic board files. One
tegra fix is important for new bootloader versions, but the bug has
been around for a while without anyone noticing.
The other changes are mostly cosmetic"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: tegra: Add missing Smaug revision
arm64: tegra: Add VDD_GPU regulator to Jetson TX1
arm64: dts: zte: clean up gic-v3 redistributor properties
arm64: dts: zx: Fix gic GICR property
bus: vexpress-config: fix device reference leak
soc: ti: qmss: fix the case when !SMP
ARM: lpc32xx: drop duplicate header device.h
ARM: ixp4xx: drop duplicate header gpio.h
ARM: socfpga: fix spelling mistake in error message
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
ARM: zx: Fix error handling
ARM: spear: Fix error handling
ARM: davinci: da850: Fix pwm name matching
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
...
best_rate is reported as potentially uninitialized by gcc.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 155e8b3b0e ("clk: bcm: Support rate change propagation on bcm2835 clocks")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some driver is using this type of DT bindings for clock (more detail,
see ${LINUX}/Documentation/devicetree/bindings/sound/simple-card.txt).
sound_soc {
...
cpu {
clocks = <&xxx>;
...
};
codec {
clocks = <&xxx>;
...
};
};
Current driver in this case uses of_clk_get() for each node, but there
is no devm_of_clk_get() today.
OTOH, the problem of having devm_of_clk_get() is that it encourages the
use of of_clk_get() when clk_get() is more desirable.
Thus, this patch adds new devm_get_clk_from_chile() which explicitly
reads as get a clock from a child node of this device.
By this function, we can also use this type of DT bindings
sound_soc {
clocks = <&xxx>, <&xxx>;
clock-names = "cpu", "codec";
clock-ranges;
...
cpu {
...
};
codec {
...
};
};
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[sboyd@codeurora.org: Rename subject to clk + add API]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Free memory mapping, if probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Free memory mapping, if of_pll_div_clk_init is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Free memory and memory mapping , if mmp2_clk_init is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
[sboyd@codeaurora.org: Put return at the right place]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Free memory and memory mapping , if pxa910_clk_init is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
It is likely that instead of '1>64', 'q>64' was expected.
Moreover, according to datasheet,
http://www.ti.com/lit/ds/symlink/cdce925.pdf
SCAS847I - JULY 2007 - REVISED OCTOBER 2016
PLL settings limits are: 16 <= q <= 63
So change the upper limit check from 64 to 63.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The broadcom clk driver Kconfig file selects and depends on the
COMMON_CLK_IPROC config for different SoC specific drivers. Let's
simplify this by always selecting the COMMON_CLK_IPROC config,
turning it into a set of library code. We still want to retain
the SoC specific options, so we leave those in place. Since we're
here we also drop COMMON_CLK dependency because that's implicitly
handled by including this file in drivers/clk/Kconfig in the
right place and also make CLK_BCM_KONA default to y on the
architecture it exists for instead of plain default y.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The VEC clock requires needs to be set at exactly 108MHz. Allow rate
change propagation on PLLH_AUX to match this requirement wihtout
impacting other IPs (PLLH is currently only used by the HDMI encoder,
which cannot be enabled when the VEC encoder is enabled).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some peripheral clocks, like the VEC (Video EnCoder) clock need to be set
to a precise rate (in our case 108MHz). With the current implementation,
where peripheral clocks are not allowed to forward rate change requests
to their parents, it is impossible to match this requirement unless the
bootloader has configured things correctly, or a specific rate has been
assigned through the DT (with the assigned-clk-rates property).
Add a new field to struct bcm2835_clock_data to specify which parent
clocks accept rate change propagation, and support set rate propagation
in bcm2835_clock_determine_rate().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
bcm2835_pll_divider_off() is resetting the divider field in the A2W reg
to zero when disabling the clock.
Make sure we preserve this value by reading the previous a2w_reg value
first and ORing the result with A2W_PLL_CHANNEL_DISABLE.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The OMAP36xx DPLL5, driving EHCI USB, can be subject to a long-term
frequency drift. The frequency drift magnitude depends on the VCO update
rate, which is inversely proportional to the PLL divider. The kernel
DPLL configuration code results in a high value for the divider, leading
to a long term drift high enough to cause USB transmission errors. In
the worst case the USB PHY's ULPI interface can stop responding,
breaking USB operation completely. This manifests itself on the
Beagleboard xM by the LAN9514 reporting 'Cannot enable port 2. Maybe the
cable is bad?' in the kernel log.
Errata sprz319 advisory 2.1 documents PLL values that minimize the
drift. Use them automatically when DPLL5 is used for USB operation,
which we detect based on the requested clock rate. The clock framework
will still compute the PLL parameters and resulting rate as usual, but
the PLL M and N values will then be overridden. This can result in the
effective clock rate being slightly different than the rate cached by
the clock framework, but won't cause any adverse effect to USB
operation.
Signed-off-by: Richard Watts <rrw@kynesim.co.uk>
[Upported from v3.2 to v4.9]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix bug https://bugzilla.kernel.org/show_bug.cgi?id=188561. Function
wm831x_clkout_is_prepared() returns "true" when it fails to read
CLOCK_CONTROL_1. "true" means the device is already prepared. So
return "true" on the read failure seems improper.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Fixes: f05259a6ff ("clk: wm831x: Add initial WM831x clock driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add more data to 64bit SoCs for the cpufreq support.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
