After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.
Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex reported the following race condition:
/* link goes up... interrupt... schedule watchdog */
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
\ e1000e_phy_has_link_generic(..., &link)
link = true
/* link goes down... interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true
/* link is up */
mac->get_link_status = false
link_active = true
/* link_active is true, wrongly, and stays so because
* get_link_status is false */
Avoid this problem by making sure that we don't set get_link_status = false
after having checked the link.
It seems this problem has been present since the introduction of e1000e.
Link: https://lkml.org/lkml/2018/1/29/338
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 19110cfbb3.
This reverts commit 4110e02eb4.
This reverts commit d3604515c9eda464a92e8e67aae82dfe07fe3c98.
Commit 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
changed what happens to the link status when there is an error which
happens after "get_link_status = false" in the copper check_for_link
callbacks. Previously, such an error would be ignored and the link
considered up. After that commit, any error implies that the link is down.
Revert commit 19110cfbb3 ("e1000e: Separate signaling for link check/link
up") and its followups. After reverting, the race condition described in
the log of commit 19110cfbb3 is reintroduced. It may still be triggered
by LSC events but this should keep the link down in case the link is
electrically unstable, as discussed. The race may no longer be
triggered by RXO events because commit 4aea7a5c5e ("e1000e: Avoid
receiver overrun interrupt bursts") restored reading icr in the Other
handler.
Link: https://lkml.org/lkml/2018/3/1/789
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Descriptor rings were not initialized at zero when allocated
When area contained garbage data, it caused skb_over_panic in
e1000_clean_rx_irq (if data had E1000_RXD_STAT_DD bit set)
This patch makes use of dma_zalloc_coherent to make sure the
ring is memset at 0 to prevent the area from containing garbage.
Following is the signature of the panic:
IODDR0@0.0: skbuff: skb_over_panic: text:80407b20 len:64010 put:64010 head:ab46d800 data:ab46d842 tail:0xab47d24c end:0xab46df40 dev:eth0
IODDR0@0.0: BUG: failure at net/core/skbuff.c:105/skb_panic()!
IODDR0@0.0: Kernel panic - not syncing: BUG!
IODDR0@0.0:
IODDR0@0.0: Process swapper/0 (pid: 0, threadinfo=81728000, task=8173cc00 ,cpu: 0)
IODDR0@0.0: SP = <815a1c0c>
IODDR0@0.0: Stack: 00000001
IODDR0@0.0: b2d89800 815e33ac
IODDR0@0.0: ea73c040 00000001
IODDR0@0.0: 60040003 0000fa0a
IODDR0@0.0: 00000002
IODDR0@0.0:
IODDR0@0.0: 804540c0 815a1c70
IODDR0@0.0: b2744000 602ac070
IODDR0@0.0: 815a1c44 b2d89800
IODDR0@0.0: 8173cc00 815a1c08
IODDR0@0.0:
IODDR0@0.0: 00000006
IODDR0@0.0: 815a1b50 00000000
IODDR0@0.0: 80079434 00000001
IODDR0@0.0: ab46df40 b2744000
IODDR0@0.0: b2d89800
IODDR0@0.0:
IODDR0@0.0: 0000fa0a 8045745c
IODDR0@0.0: 815a1c88 0000fa0a
IODDR0@0.0: 80407b20 b2789f80
IODDR0@0.0: 00000005 80407b20
IODDR0@0.0:
IODDR0@0.0:
IODDR0@0.0: Call Trace:
IODDR0@0.0: [<804540bc>] skb_panic+0xa4/0xa8
IODDR0@0.0: [<80079430>] console_unlock+0x2f8/0x6d0
IODDR0@0.0: [<80457458>] skb_put+0xa0/0xc0
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<804079c8>] e1000_clean_rx_irq+0x188/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80468b48>] __dev_kfree_skb_any+0x88/0xa8
IODDR0@0.0: [<804101ac>] e1000e_poll+0x94/0x288
IODDR0@0.0: [<8046e9d4>] net_rx_action+0x19c/0x4e8
IODDR0@0.0: ...
IODDR0@0.0: Maximum depth to print reached. Use kstack=<maximum_depth_to_print> To specify a custom value (where 0 means to display the full backtrace)
IODDR0@0.0: ---[ end Kernel panic - not syncing: BUG!
Signed-off-by: Pierre-Yves Kerbrat <pkerbrat@kalray.eu>
Signed-off-by: Marius Gligor <mgligor@kalray.eu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When autoneg is off, the .check_for_link callback functions clear the
get_link_status flag and systematically return a "pseudo-error". This means
that the link is not detected as up until the next execution of the
e1000_watchdog_task() 2 seconds later.
Fixes: 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82574 specification update errata 12 states that interrupts may be
missed if ICR is read while INT_ASSERTED is not set. Avoid that problem by
setting all bits related to events that can trigger the Other interrupt in
IMS.
The Other interrupt is raised for such events regardless of whether or not
they are set in IMS. However, only when they are set is the INT_ASSERTED
bit also set in ICR.
By doing this, we ensure that INT_ASSERTED is always set when we read ICR
in e1000_msix_other() and steer clear of the errata. This also ensures that
ICR will automatically be cleared on read, therefore we no longer need to
clear bits explicitly.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Restores the ICS write for Rx/Tx queue interrupts which was present before
commit 16ecba59bc ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1)
but was not restored in commit 4aea7a5c5e
("e1000e: Avoid receiver overrun interrupt bursts", v4.15-rc1).
This re-raises the queue interrupts in case the txq or rxq bits were set in
ICR and the Other interrupt handler read and cleared ICR before the queue
interrupt was raised.
Fixes: 4aea7a5c5e ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This partially reverts commit 4aea7a5c5e.
We keep the fix for the first part of the problem (1) described in the log
of that commit, that is to read ICR in the other interrupt handler. We
remove the fix for the second part of the problem (2), Other interrupt
throttling.
Bursts of "Other" interrupts may once again occur during rxo (receive
overflow) traffic conditions. This is deemed acceptable in the interest of
avoiding unforeseen fallout from changes that are not strictly necessary.
As discussed, the e1000e driver should be in "maintenance mode".
Link: https://www.spinics.net/lists/netdev/msg480675.html
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It was reported that emulated e1000e devices in vmware esxi 6.5 Build
7526125 do not link up after commit 4aea7a5c5e ("e1000e: Avoid receiver
overrun interrupt bursts", v4.15-rc1). Some tracing shows that after
e1000e_trigger_lsc() is called, ICR reads out as 0x0 in e1000_msix_other()
on emulated e1000e devices. In comparison, on real e1000e 82574 hardware,
icr=0x80000004 (_INT_ASSERTED | _LSC) in the same situation.
Some experimentation showed that this flaw in vmware e1000e emulation can
be worked around by not setting Other in EIAC. This is how it was before
16ecba59bc ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1).
Fixes: 4aea7a5c5e ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I personally spent a long time trying to decypher why my CPU would not
reach deeper C-states. Let's just tell the next user what's going on.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to section 12.0.3.4.13 "Receive Descriptor Control - RXDCTL"
of the Intel® 82579 Gigabit Ethernet PHY Datasheet v2.1:
"HTHRESH should be given a non zero value when ever PTHRESH is
used."
In RXDCTL(0), PTHRESH lives at bits 5:0, and HTHREST lives at bits 13:8.
Set only bit 8 of HTHREST as is done in e1000_flush_rx_ring(). Found by
inspection.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e_check_for_copper_link() and e1000_check_for_copper_link_ich8lan()
are the two functions that may be assigned to mac.ops.check_for_link when
phy.media_type == e1000_media_type_copper. Commit 19110cfbb3 ("e1000e:
Separate signaling for link check/link up") changed the meaning of the
return value of check_for_link for copper media but only adjusted the first
function. This patch adjusts the second function likewise.
Reported-by: Christian Hesse <list@eworm.de>
Reported-by: Gabriel C <nix.or.die@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198047
Fixes: 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Christian Hesse <list@eworm.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a follow on to commit b10effb92e ("fix buffer overrun while the
I219 is processing DMA transactions") to address David Laights concerns
about the use of "magic" numbers. So define masks as well as add
additional code comments to give a better understanding of what needs to
be done to avoid a buffer overrun.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Alexander H Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e_put_txbuf() can be called from normal reclamation path as well as
when a DMA mapping failure, so we need to differentiate these two cases
when freeing SKBs to be drop monitor friendly. e1000e_tx_hwtstamp_work()
and e1000_remove() are processing TX timestamped SKBs and those should
not be accounted as drops either.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Devices that support FLAG2_DMA_BURST have different default values
for RDTR and RADV. Apply burst mode default settings only when no
explicit value was passed at module load.
The RDTR default is zero. If the module is loaded for low latency
operation with RxIntDelay=0, do not override this value with a burst
default of 32.
Move the decision to apply burst values earlier, where explicitly
initialized module variables can be distinguished from defaults.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Intel® 100/200 Series Chipset platforms reduced the round-trip
latency for the LAN Controller DMA accesses, causing in some high
performance cases a buffer overrun while the I219 LAN Connected
Device is processing the DMA transactions. I219LM and I219V devices
can fall into unrecovered Tx hang under very stressfully UDP traffic
and multiple reconnection of Ethernet cable. This Tx hang of the LAN
Controller is only recovered if the system is rebooted. Slightly slow
down DMA access by reducing the number of outstanding requests.
This workaround could have an impact on TCP traffic performance
on the platform. Disabling TSO eliminates performance loss for TCP
traffic without a noticeable impact on CPU performance.
Please, refer to I218/I219 specification update:
https://www.intel.com/content/www/us/en/embedded/products/networking/
ethernet-connection-i218-family-documentation.html
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.
This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.
Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59bc
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit
0a8047ac68 ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Fixes: 16ecba59bc ("e1000e: Do not read ICR in Other interrupt")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lennart reported the following race condition:
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;
/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reading e1000e_check_for_copper_link() shows that get_link_status is set to
false after link has been detected. Therefore, it stays TRUE until then.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i219 (8) and i219 (9) are the next LOM generations that will be available
on the next Intel Client platform (IceLake).
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check return value from call to e1e_wphy(). This value is being
checked during previous calls to function e1e_wphy() and it seems
a check was missing here.
Addresses-Coverity-ID: 1226905
Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com>
Reviewed-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace disable_irq() which waits for threaded irq handlers with
disable_hardirq() which waits only for hardirq part.
Fixes: 3111912971 ("e1000: use disable_hardirq() for e1000_netpoll()")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some statistics passed to ethtool are garbage because e1000e_get_stats64()
doesn't write them, for example: tx_heartbeat_errors. This leaks kernel
memory to userspace and confuses users.
Do like ixgbe and use dev_get_stats() which first zeroes out
rtnl_link_stats64.
Fixes: 5944701df9 ("net: remove useless memset's in drivers get_stats64")
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000e driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000e driver and related hardware has a limitation on Tx PTP
packets which requires we limit to timestamping a single packet at once.
We do this by verifying that we never request a new Tx timestamp while
we still have a tx_hwtstamp_skb pointer.
Unfortunately the driver suffers from a race condition around this. The
tx_hwtstamp_skb pointer is not set to NULL until after skb_tstamp_tx()
is called. This function notifies the stack and applications of a new
timestamp. Even a well behaved application that only sends a new request
when the first one is finished might be woken up and possibly send
a packet before we can free the timestamp in the driver again. The
result is that we needlessly ignore some Tx timestamp requests in this
corner case.
Fix this by assigning the tx_hwtstamp_skb pointer prior to calling
skb_tstamp_tx() and use a temporary pointer to hold the timestamped skb
until that function finishes. This ensures that the application is not
woken up until the driver is ready to begin timestamping a new packet.
This ensures that well behaved applications do not accidentally race
with condition to skip Tx timestamps. Obviously an application which
sends multiple Tx timestamp requests at once will still only timestamp
one packet at a time. Unfortunately there is nothing we can do about
this.
Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some drivers were calling the skb_tx_timestamp() function only when
a hardware timestamp was not requested. Now that applications can use
the SOF_TIMESTAMPING_OPT_TX_SWHW option to request both software and
hardware timestamps, the drivers need to be modified to unconditionally
call skb_tx_timestamp().
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid
filter and update drivers which can timestamp all packets, or which
explicitly list unsupported filters instead of using a default case, to
handle the filter.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 38.4MHz frequency is required for PTP
on CannonLake. SYSTIM frequency adjustment attributes for TIMINCA are
get/set dependent on the hardware clock frequency for a different
types of adapters. 38.4MHz frequency supported by CannonLake
and active once time synchronisation mechanism was enabled
Changed abbreviation from Hz to HZ to be compliant checkpatch code style
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The propagation of CannonLake mac type to driver functionality
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i219 (6) and i219 (7) are the next LOM generations that will be
available on the nextIntel Client platform (CannonLake)
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I've got reports that the Intel I-218V NIC in Intel NUC5i5RYH systems used
as a PTP slave experiences random ~10 hour clock jumps, which are resolved
if the same workaround for the 82574 and 82583 is employed, so set the
appropriate flag2 in e1000_pch_lpt_info too.
Reported-by: Rupesh Patel <rupatel@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After an upgrade to Linux kernel v4.x the hardware timestamps of the
82579 Gigabit Ethernet Controller are different than expected.
The values that are being read are almost four times as big as before
the kernel upgrade.
The difference is that after the upgrade the driver sets the clock
frequency to 25MHz, where before the upgrade it was set to 96MHz. Intel
confirmed that the correct frequency for this network adapter is 96MHz.
Signed-off-by: Bernd Faust <berndfaust@gmail.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7e54d9d063.
After additional regression testing, several users are experiencing
kernel panics during shutdown on e1000e devices. Reverting this
change resolves the issue.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f24273837 ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f4 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dac ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dev_get_stats() the statistic structure storage has already been
zeroed. Therefore network drivers do not need to call memset() again.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During systemd reboot sequence network driver interface is shutdown
by e1000_close. The PCI driver interface is shut by e1000_shutdown.
The e1000_shutdown checks for netif_running status, if still up it
brings down driver. But it disables msi outside of this if statement,
regardless of netif status. All this is OK when e1000_close happens
after shutdown. However, by default, everything in systemd is done
in parallel. This creates a conditions where e1000_shutdown is called
after e1000_close, therefore hitting BUG_ON assert in free_msi_irqs.
CC: xe-kernel@external.cisco.com
Signed-off-by: khalidm <khalidm@cisco.com>
Signed-off-by: David Singleton <davsingl@cisco.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
In commit 02cea39586 ("genirq: Provide disable_hardirq()")
Peter introduced disable_hardirq() for netpoll, but it is forgotten
to use it for e1000.
This patch changes disable_irq() to disable_hardirq() for e1000.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
and no longer serves a purpose. No need to set min_mtu or max_mtu
explicitly, as ether_setup() will already set them to 68 and 1500.
e1000: min_mtu 46, max_mtu 16110
e1000e: min_mtu 68, max_mtu varies based on adapter
fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now
i40e: min_mtu 68, max_mtu 9706
i40evf: min_mtu 68, max_mtu 9706
igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
the driver, the larger value wasn't relevant though, so I've set max_mtu
to the smaller of the two values here to retain identical behavior.
igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated
ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu
ixgbe: min_mtu 68, max_mtu 9710
ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers must be ready to accept NULL from ptp_clock_register() if the
PTP clock subsystem is configured out.
This patch documents that and ensures that all drivers cope well
with a NULL return.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Eugenia Emantayev <eugenia@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've got reports that the Intel I-218V NIC in Intel NUC5i5RYH systems used
as a PTP slave experiences random ~10 hour clock jumps, which are resolved
if the same workaround for the 82574 and 82583 is employed, so set the
appropriate flag2 in e1000_pch_lpt_info too.
Reported-by: Rupesh Patel <rupatel@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
