Reject the modeset if the requested dotclock exceeds the maximum allowed
by the hardware. So far we've only checked this on gen2/3 while also
handling the double wide vs. single wide pipe selection. Extend the
check to all platforms since we have the max dotclock correctly
populated now across the board.
Testcase: igt/kms_invalid_dotclock
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464114859-15610-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Thanks to Ville Syrjälä for pointing me towards the cause of this issue.
Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:
[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config] FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config] scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A
Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.
A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.
Changes since v3:
- Move temp variable into loop
- Move checks for using_ssc_source to after we've figured out has_ck505
- Add using_ssc_source to debug output
Changes since v2:
- Fix debug output for when we disable the CPU source
Changes since v1:
- Leave the SSC source clock on instead of just shutting it off on all
of the DPLL configurations.
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1464199863-9397-1-git-send-email-cpaul@redhat.com
I noticed that during S4 resume BIOS incorrectly sets bits 18, 19 which
are reserved/MBZ and sets the decimal frequency fields to all 0xff in
the CDCLK register. The result is a hard lockup as display register
accesses are attempted later. Work around this by sanitizing the CDCLK
PLL/dividers the same way it's done on SKL.
While this is clearly a BIOS bug which should be fixed separately, it
doesn't hurt to check/sanitize this regardless.
v2:
- Use the same condition for VCO and CDCLK in broxton_init_cdclk as is
used in skl_init_cdclk for the same purpose.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464093513-16258-2-git-send-email-imre.deak@intel.com
If the CDCLK PLL isn't locked or incorrectly configured we can just
assume that it's off resulting in fully re-initializing both CDCLK PLL
and CDCLK dividers. This way the CDCLK PLL sanitization added in the
following patch can be done on BXT the same way as it's done on SKL.
v2: (Ville)
- Remove the remaining PLL specific checks from skl_sanitize_cdclk() and
depend instead on the corresponding check in skl_dpll0_update().
- Use vco == 0 instead of the corresponding boolean check in
skl_sanitize_cdclk().
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464093513-16258-1-git-send-email-imre.deak@intel.com
This reverts the following patches:
d55dbd06bb drm/i915: Allow nonblocking update of pageflips.
15c86bdb76 drm/i915: Check for unpin correctness.
95c2ccdc82 Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
a6747b7304 drm/i915: Make unpin async.
03f476e1fc drm/i915: Prepare connectors for nonblocking checks.
2099deffef drm/i915: Pass atomic states to fbc update functions.
ee7171af72 drm/i915: Remove reset_counter from intel_crtc.
2ee004f7c5 drm/i915: Remove queue_flip pointer.
b8d2afae55 drm/i915: Remove use_mmio_flip kernel parameter.
8dd634d922 drm/i915: Remove cs based page flip support.
143f73b3bf drm/i915: Rework intel_crtc_page_flip to be almost atomic, v3.
84fc494b64 drm/i915: Add the exclusive fence to plane_state.
6885843ae1 drm/i915: Convert flip_work to a list.
aa420ddd8e drm/i915: Allow mmio updates on all platforms, v2.
afee4d8707 Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
"drm/i915: Allow nonblocking update of pageflips" should have been
split up, misses a proper commit message and seems to cause issues in
the legacy page_flip path as demonstrated by kms_flip.
"drm/i915: Make unpin async" doesn't handle the unthrottled cursor
updates correctly, leading to an apparent pin count leak. This is
caught by the WARN_ON in i915_gem_object_do_pin which screams if we
have more than DRM_I915_GEM_OBJECT_MAX_PIN_COUNT pins.
Unfortuantely we can't just revert these two because this patch series
came with a built-in bisect breakage in the form of temporarily
removing the unthrottled cursor update hack for legacy cursor ioctl.
Therefore there's no other option than to revert the entire pile :(
There's one tiny conflict in intel_drv.h due to other patches, nothing
serious.
Normally I'd wait a bit longer with doing a maintainer revert, but
since the minimal set of patches we need to revert (due to the bisect
breakage) is so big, time is running out fast. And very soon
(especially after a few attempts at fixing issues) it'll be really
hard to revert things cleanly.
Lessons learned:
- Not a good idea to rush the review (done by someone fairly new to
the area) and not make sure domain experts had a chance to read it.
- Patches should be properly split up. I only looked at the two
patches that should be reverted in detail, but both look like the
mix up different things in one patch.
- Patches really should have proper commit messages. Especially when
doing more than one thing, and especially when touching critical and
tricky core code.
- Building a patch series and r-b stamping it when it has a built-in
bisect breakage is not a good idea.
- I also think we need to stop building up technical debt by
postponing atomic igt testcases even longer. I think it's clear that
there's enough corner cases in this beast that we really need to
have the testcases _before_ the next step lands.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
One of the uses for i915_gem_objects is pin-pointing leaks. For this, we
can compare the number of allocated objects and who owns them, a
discrepancy here often indicates a kernel bug. One allocator of unreported
objects is for backing context objects, so include those in the listing.
v2: Take filelist_mutex which requires a little dance with struct_mutex
to avoid nesting filelist_mutex inside struct_mutex.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-10-git-send-email-chris@chris-wilson.co.uk
struct intel_context contains two substructs, one for the legacy RCS and
one for every execlists engine. Since legacy RCS is a subset of the
execlists engine support, just combine the two substructs.
v2: Only pin the default context for legacy mode (the object only exists
for legacy, but adding i915.enable_execlists provides symmetry with the
cleanup functions).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-8-git-send-email-chris@chris-wilson.co.uk
Just move the kernel_context member of drm_i915_private next to the
engines it is associated with.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-7-git-send-email-chris@chris-wilson.co.uk
Print the context's owner (via the pid under file_priv) under debugfs.
In doing so, we must be careful that the filp is not accessed after it
is freed (notified via i915_gem_context_close).
v2: Mark the file_priv as closed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-6-git-send-email-chris@chris-wilson.co.uk
Rather than have every context ask "am I owned by the kernel? pin!",
move that logic into the creator of the kernel context, in order to
improve code comprehension.
v2: Throw away the user_handle on failure to allocate the ppgtt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-5-git-send-email-chris@chris-wilson.co.uk
We want to give a name to the currently anonymous per-engine struct
inside the context, so that we can assign it to a local variable and
save clumsy typing. The name we have chosen is intel_context as it
reflects the HW facing portion of the context state (the logical context
state, the registers, the ringbuffer etc).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-4-git-send-email-chris@chris-wilson.co.uk
i915_gem_context_get() is a very simple wrapper around idr_find(), so
simple that it would be smaller to do the lookup inline. Also we use the
verb 'lookup' to return a pointer from a handle, freeing 'get' to imply
obtaining a reference to the context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-3-git-send-email-chris@chris-wilson.co.uk
Our goal is to rename the anonymous per-engine struct beneath the
current intel_context. However, after a lively debate resolving around
the confusion between intel_context_engine and intel_engine_context, the
realisation is that the two structs target different users. The outer
struct is API / user facing, and so carries the higher level GEM
information. The inner struct is hw facing. Thus we want to name the
inner struct intel_context and the outer one i915_gem_context. As the
first step, we need to rename the current struct:
s/struct intel_context/struct i915_gem_context/
which fits much better with its constructors already conveying the
i915_gem_context prefix!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-1-git-send-email-chris@chris-wilson.co.uk
New GuC code is logging errors at runtime suspend and resume which
causes CI testing to log "orange" status. Default to not trying to
load the firmware until this is resolved.
Example of the log:
[drm] RC6 on
[drm:intel_runtime_suspend] Suspending device
[drm:host2guc_action [i915]] *ERROR* GUC: host2guc action 0x501 failed. ret=-110 status=0x00000501 response=0x40000000
...
[drm:intel_runtime_resume] Resuming device
[drm:host2guc_action [i915]] *ERROR* GUC: host2guc action 0x502 failed. ret=-110 status=0x00000502 response=0x40000000
[drm:intel_runtime_resume] Device resumed
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Harris <chris.harris@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1464017675-12257-1-git-send-email-tvrtko.ursulin@linux.intel.com
Like with cdclk, the DMC is supposed to manage dbuf enabling/disabling.
Let's make sure it has correctly restored the dbuf state to enabled
when we disable the DC states.
v2: s/skl/gen9/ in function name (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Suggested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463407180-28993-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
In case the driver is initialized without active displays, we should
just drop the cdclk to the minimum frequency right off the bat. There
might not be a modeset to drop it to the minimum late rafter all.
With DMC supposedly we should always have the cdclk up and running.
The DMC will shut the DE PLL down when appropriate, so let's nuke
the related FIXMEs as well. Trying to do anything different would
go against the expectations of the DMC firmware, and we all know
how fragile the DMC firmware is.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-22-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Rather than having a BXT specific function to make sure the DE PLL is
enabled after disabling DC6, let's just make sure the current cdclk
is the same as what we last programmed.
Having another check in bxt_display_core_init() almost immediately after
the cdclk init seems redundant, so let's just kill that one.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-21-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Make bxt_set_cdclk() more readable by looking at current vs. target
DE PLL vco to determine if the DE PLL needs disabling and/or enabling.
We can also calculate the CD2X divider simply as (vco/cdclk) instead of
depending on magic numbers.
The magic numbers are still needed though, but only to map the supported
cdclk frequencies to corresponding DE PLL frequencies.
Note that w'll now program CDCLK_CTL correctly even for the bypass case.
Actually the CD2X divider should not matter in that case since the
hardware will bypass it too, but the "decimal" part should matter (if we
want to do gmbus/aux with the bypass enabled).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-20-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
We'll want to store the cdclk PLL (whatever PLL that is in reality) vco
frequency somewhere on other platforms too, so let's rename the
skl_vco_freq to cdclk_pll.vco, and let's store it in kHz instead of MHz
to match most of the other clocks.
v2: Drop the spurious > vs != change (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-14-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The SKL 308.57 MHz cdclk is probably 8640/28 = ~308.571 Mhz.
Similartly the 617.14 MHz cdclk is probably 8640/14 = ~617.143 MHz.
Let's use the slightly more accurate numbers. Potentially we might
change to computing all of these based on dividers, but let's
stick to the current theme for now..
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
SKL and BXT have the same snippets of code for enabling disabling the
DBUF. Extract those into helpers and move the calls from
init/unit_cdclk() to the display core init/init since this stuff isn't
really about cdclk. Also doing the enable twice shouldn't hurt since
you're just setting the request bit again when it was already set.
We can also toss in a few WARNs about the register values into
skl_get_dpll0_vco() now that we know that things should always be
sane there.
Flatten skl_init_cdclk() while at it.
v2: s/skl/gen9/ in function names (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we initialize cdclk on SKL from two different places,
depending on whether it's during driver init or resume. Let's
unify it to happen from the same place always, and that place will be
the display core init function.
To do this we first run through the cdclk sanitation code, which will
first verify that the PLL is programmed correctly, after which we can
read out the current cdclk frequency, and once the cdclk is known we
verify that the cdclk "decimal" frequency is programmed correctly. If
any of these fail we will force a cdclk change, and to be safe we also
force the PLL to be turned off and on again. If the sanitation step
didn't notice anything amiss, we'll skip the cdclk programming which
will prevent cdclk reprogramming when the displays might be active.
We can also toss in a few WARNs about the register values into
skl_update_dpll0() since we now know that the PLL state should
always be sane when that function is called.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Now that skl_vco_freq tracks the actual DPLL0 vco frequency, we'll need
something that keeps track of which vco frequency we want to use in case
the current vco is 0. This would be important across supend/resume since
we'll disable DPLL0 around those parts.
We'll also update our idea of max cdclk/dotclock when the preferred
vco changes. That could happen if out initial guess was wrong, and
later eDP would force us to change it. One issue here could be that
changing the max dotclock could cause our mode list to change during
next time the displays get probed. But I don't see a good way to avoid
that, except perhaps by allowing either vco frequency to be used as
needed. But the docs suggest that such usage wasn't really inteded.
Also need to make sure we don't update our max_cdclk value before we
have a preferred vco value, which means moving that to happen after
the cdclk sanitation.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
In case we originally guessed wrong which lcpll vco frequency to use,
we will need to shut down the pll and restart it when reprogamming the
cdclk.
This also allows us to track the actual vco frequency in dev_priv
instead of just a guess.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-8-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we're trying to guess which lcpll vco frequency is used
use based on the cdclk. That doesn't work for cdclk==540 since
both vco frequencies can generate a 540 Mhz output. Let's stop
guessing and just read the actual vco frequency from the
hardware.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Shared plls won't get assigned until the .compute_clocks() hook gets
called, which happens from the crtc .atomic_check hook. That's too late
as the cdclk computation has already happened. So let's move the DPLL0
VCO computation into intel_dp_compute_config() so that it's done when
the cdclk computation happens. Also only do it for eDP since we only
pick DPLL0 for eDP.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
WARNING: Using ChromeOS with an eDP panel and a 4K@60 DP monitor connected
to DDI1 the system will hard hang during a cold boot. Occurs when DDI1
is enabled when the cdclk is less then required. DP connected to DDI2
and HPD on either port works correctly.
Set cdclk based on the max required pixel clock based on VCO
selected. Track boot vco instead of boot cdclk.
The vco is now tracked at the atomic level and all CRTCs updated if
the required vco is changed. Not tested with eDP v1.4 panels that
require 8640 vco due to availability.
V1: initial version
V2: add vco tracking in intel_dp_compute_config(), rename
skl_boot_cdclk.
V3: rebase, V2 feedback not possible as encoders are not aware of
atomic.
V4: track target vco is atomic state. modeset all CRTCs if vco changes
V5: rename atomic variable, cleaner if/else logic, use existing vco if
encoder does not return a new vco value. check_patch.pl cleanup
V6: simplify logic in intel_modeset_checks.
V7: reorder an IF for readability and whitespace fix.
V8: use dev_cdclk for tracking new cdclk during atomic
V9: correctly handle vco 8640 when crtcs==0
V10: Clean up if else in crtcs==0
V11: Rebase for new intel_dpll_mgr.c
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
[vsyrjala: rebased due to churn]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-3-git-send-email-ville.syrjala@linux.intel.com
commit 4e5ca60fd3 ("drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation")
tried to change BXT to use ilk_max_pixel_rate() to compute the
pipe pixel rate. I failed to notice that there was another place
in the state readout code that needs the same treatment. So let's
change that one too.
Should probably just change things to always compuyte the pipe pixel
rates, instead of just doing on platforms that can change cdclk
dynamically. But for now let's just move BXT fully over to the
side that uses ilk_pipe_pixel_rate().
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 4e5ca60fd3 ("drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Current intel_opregion_init is called during the driver registration
phase and intel_opregion_fini from the unregistration phase. Rename the
functions so that this is clear from their names. The phases tell us
what we expect the existing hw state to be, e.g. whether interrupts are
still enabled etc.
It should be noted that the opregion init/fini routines are asymmetric
and this is carried across into their new names. Indeed, their new names
make it even clearer that perhaps all is not well in the opregion
suspend/resume sequence (as well in the module unload).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464012490-30961-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Prefer passing struct drm_i915_private to internal interfaces as this
saves us having to dance between drm_device and our native struct. The
savings hare are small (only 70 bytes of unrequired dancing), but
progressive!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464012490-30961-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
We've never actually enabled or unmasked the GSE interrupt on BDW+,
even though the interrupt handler was always prepared for it.
Let's enable it and see what happens.
Credit to Mark Kettenis who fixed this in the OpenBSD fork of the
driver. He reports that it fixed the "ACPI _BCM/_BCQ-based
brightness mechanism on a MacBookPro12,1 and a 3rd gen Lenovo X1
Carbon" for them.
Mark says:
"FWIW, this *is* needed if you want ACPI-based backlight control to
work. On Linux you probably don't notice, since "hardware" backlight
control is preferred over "firmware" or "platform" backlight control.
It would help me if this did land in the Linux tree though, as it will
make future imports of the i915 driver into OpenBSD easier."
So even though we don't really need this, let's put it in to help Mark
with future porting efforts. Should be harmless to have it enabled in
any case.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
References: http://lists.freedesktop.org/archives/intel-gfx/2015-December/081799.html
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Cc: Mark Kettenis <mark.kettenis@xs4all.nl>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463649283-28698-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Mostly little optimisations and future-proofing against code breakage.
For instance, if the driver is correctly following the submission
protocol, the "out of space" condition is impossible, so the previous
runtime WARN_ON() is promoted to a GEM_BUG_ON() for a more dramatic
effect in development and less impact in end-user systems.
Similarly we can make alignment checking more stringent and replace
other WARN_ON() conditions that don't relate to the runtime hardware
state with either BUILD_BUG_ON() for compile-time-detectable issues, or
GEM_BUG_ON() for logical "can't happen" errors.
With those changes, we can convert it to void, as suggested by Chris
Wilson, and update the calling code appropriately.
v2:
Note that we're now putting the request seqno in the "fence_id"
field of each GuC-work-item, in case it turns up somewhere useful
(e.g. in a GuC log) [Tvrtko Ursulin].
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Rather than wait to see whether more space becomes available in the GuC
submission workqueue, we can just return -EAGAIN and let the caller try
again in a little while. This gets rid of an uninterruptable sleep in
the polling code :)
We'll also add a counter to the GuC client statistics, to see how often
we find the WQ full.
v2:
Flag the likely() code path (Tvtrko Ursulin).
v4:
Add/update comments about failure counters (Tvtrko Ursulin).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The knowledge of how to derive the relevant client from the request
should be localised within i915_guc_submission.c; the LRC code shouldn't
have to know about the internal details of the GuC submission process.
And all the information the GuC code needs should be encapsulated in (or
reachable from) the request.
v2:
GEM_BUG_ON() for bad GuC client (Tvrtko Ursulin).
Add/update kerneldoc explaining check_space/submit protocol
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Split the function of "enable_guc_submission" into two separate
options. The new one ("enable_guc_loading") controls only the
*fetching and loading* of the GuC firmware image. The existing
one is redefined to control only the *use* of the GuC for batch
submission once the firmware is loaded.
In addition, the degree of control has been refined from a simple
bool to an integer key, allowing several options:
-1 (default) whatever the platform default is
0 DISABLE don't load/use the GuC
1 BEST EFFORT try to load/use the GuC, fallback if not available
2 REQUIRE must load/use the GuC, else leave the GPU wedged
The new platform default (as coded here) will be to attempt to
load the GuC iff the device has a GuC that requires firmware,
but not yet to use it for submission. A later patch will change
to enable it if appropriate.
v4:
Changed some error-message levels, mostly ERROR->INFO, per
review comments by Tvrtko Ursulin.
v5:
Dropped one more error message, disabled GuC submission on
hypothetical firmware-free devices [Tvrtko Ursulin].
v6:
Logging tidy by Tvrtko Ursulin:
* Do not log falling back to execlists when wedging the GPU.
* Do not log fw load errors when load was disabled by user.
* Pass down some error code from fw load for log message to
make more sense.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: Fiedorowicz, Lukasz <lukasz.fiedorowicz@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com> (v6)
For now, anything with a GuC requires uCode loading, and then supports
command submission once loaded. But these are logically distinct from
simply "having a GuC", so we need a separate macro for the latter. Then,
various tests should use this new macro rather than HAS_GUC_UCODE() or
testing enable_guc_submission.
v4:
Added a couple more uses of the new macro.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The GuC initialisation code could do other things apart from loading
firmware, so here we rename the three primary entry points to remove any
specific reference to "ucode" (no functional changes, just renaming).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
