Add a new 'three-p' precise level, that uses INST_RETIRED.PREC_DIST as
base. The basic mechanism of abusing the inverse cmask to get all
cycles works the same as before.
PREC_DIST is available on Sandy Bridge or later. It had some problems
on Sandy Bridge, so we only use it on IvyBridge and later. I tested it
on Broadwell and Skylake.
PREC_DIST has special support for avoiding shadow effects, which can
give better results compare to UOPS_RETIRED. The drawback is that
PREC_DIST can only schedule on counter 1, but that is ok for cycle
sampling, as there is normally no need to do multiple cycle sampling
runs in parallel. It is still possible to run perf top in parallel, as
that doesn't use precise mode. Also of course the multiplexing can
still allow parallel operation.
:pp stays with the previous event.
Example:
Sample a loop with 10 sqrt with old cycles:pp
0.14 │10: sqrtps %xmm1,%xmm0 <--------------
9.13 │ sqrtps %xmm1,%xmm0
11.58 │ sqrtps %xmm1,%xmm0
11.51 │ sqrtps %xmm1,%xmm0
6.27 │ sqrtps %xmm1,%xmm0
10.38 │ sqrtps %xmm1,%xmm0
12.20 │ sqrtps %xmm1,%xmm0
12.74 │ sqrtps %xmm1,%xmm0
5.40 │ sqrtps %xmm1,%xmm0
10.14 │ sqrtps %xmm1,%xmm0
10.51 │ ↑ jmp 10
We expect all 10 sqrt to get roughly the sample number of samples.
But you can see that the instruction directly after the JMP is
systematically underestimated in the result, due to sampling shadow
effects.
With the new PREC_DIST based sampling this problem is gone and all
instructions show up roughly evenly:
9.51 │10: sqrtps %xmm1,%xmm0
11.74 │ sqrtps %xmm1,%xmm0
11.84 │ sqrtps %xmm1,%xmm0
6.05 │ sqrtps %xmm1,%xmm0
10.46 │ sqrtps %xmm1,%xmm0
12.25 │ sqrtps %xmm1,%xmm0
12.18 │ sqrtps %xmm1,%xmm0
5.26 │ sqrtps %xmm1,%xmm0
10.13 │ sqrtps %xmm1,%xmm0
10.43 │ sqrtps %xmm1,%xmm0
0.16 │ ↑ jmp 10
Even with PREC_DIST there is still sampling skid and the result is not
completely even, but systematic shadow effects are significantly
reduced.
The improvements are mainly expected to make a difference in high IPC
code. With low IPC it should be similar.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: hpa@zytor.com
Link: http://lkml.kernel.org/r/1448929689-13771-2-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I added UOPS_RETIRED.ALL by mistake to the Skylake PEBS event list for
cycles:pp. But the event is not documented for Skylake, and has some
issues.
The recommended replacement for cycles:pp is to use
INST_RETIRED.ANY+pebs as a base, similar to what CPUs before Sandy
Bridge did. This new event is called INST_RETIRED.TOTAL_CYCLES_PS. The
event is not really new, but has been already used by perf before
Sandy Bridge for the original cycles:p
Note the SDM doesn't document that event either, but it's being
documented in the latest version of the event list on:
https://download.01.org/perfmon/SKL
This patch does:
- Remove UOPS_RETIRED.ALL from the Skylake PEBS event list
- Add INST_RETIRED.ANY to the Skylake PEBS event list, and an table entry to
allow cmask=16,inv=1 for cycles:pp
- We don't need an extra entry for the base INST_RETIRED event,
because it is already covered by the catch-all PEBS table entry.
- Switch Skylake to use the Core2 PEBS alias (which is
INST_RETIRED.TOTAL_CYCLES_PS)
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: hpa@zytor.com
Link: http://lkml.kernel.org/r/1448929689-13771-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Normally we drop PEBS events with a zero status field. But when
there is only a single PEBS event active we can assume the
PEBS record is for that event. The PEBS buffer is always flushed
when PEBS events are disabled, so there is no risk of mishandling
state PEBS records this way.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1449177740-5422-2-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The recent commit:
75f80859b1 ("perf/x86/intel/pebs: Robustify PEBS buffer drain")
causes lots of warnings on different CPUs before Skylake
when running PEBS intensive workloads.
They can have a zero status field in the PEBS record when
PEBS is racing with clearing of GLOBAl_STATUS.
This also can cause hangs (it seems there are still
problems with printk in NMI).
Disable the warning, but still ignore the record.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1449177740-5422-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull perf fixes from Ingo Molnar:
"This tree includes four core perf fixes for misc bugs, three fixes to
x86 PMU drivers, and two updates to old email addresses"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Do not send exit event twice
perf/x86/intel: Fix INTEL_FLAGS_UEVENT_CONSTRAINT_DATALA_NA macro
perf/x86/intel: Make L1D_PEND_MISS.FB_FULL not constrained on Haswell
perf: Fix PERF_EVENT_IOC_PERIOD deadlock
treewide: Remove old email address
perf/x86: Fix LBR call stack save/restore
perf: Update email address in MAINTAINERS
perf/core: Robustify the perf_cgroup_from_task() RCU checks
perf/core: Fix RCU problem with cgroup context switching code
Now that we have generic MSR trace points we can remove the old
hackish perf MSR read tracing code.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: rostedt@goodmis.org
Link: http://lkml.kernel.org/r/1449018060-1742-4-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix a definition in the perf rapl driver. __initconst must
be applied to a const object, but to declare a const pointer
you need to use * const ..., not const ... *
This fixes a section attribute conflict with LTO builds.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1448905722-2767-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We need to add rest of the flags to the constraint mask
instead of another INTEL_ARCH_EVENT_MASK, fixing a typo.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1447061071-28085-1-git-send-email-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Running microcode_init() from setup_arch() is a bad idea because
not even kmalloc() is ready at that point and the loader does
all kinds of allocations and init/registration with various
subsystems.
Make it a late initcall when required facilities are initialized
so that the microcode driver initialization can succeed too.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20151120112400.GC4028@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The earlier constraint fix for Broadwell CYCLE_ACTIVITY.*
forced umask 8 to counter 2. For this it used UEVENT,
to match the complete umask.
The event list for Broadwell has an additional
STALLS_L1D_PENDIND event that uses umask 8, but also
sets other bits in the umask. The earlier strict umask match
didn't handle this case.
Add a new UBIT_EVENT constraint macro that only matches
the specified bits in the umask. Then use that macro
to handle CYCLE_ACTIVITY.* on Broadwell.
The documented event also uses cmask, but there's no
need to let the event scheduler know about the cmask,
as the scheduling restriction is only tied to the umask.
Reported-by: Grant Ayers <ayers@cs.stanford.edu>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1447719667-9998-1-git-send-email-andi@firstfloor.org
[ Filled in the missing email address of Grant Ayers - hopefully I got the right one. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch add a function for external components to stop Intel PT.
Basically this function is used when kernel panic occurs. When it is
called, the intel_pt driver disables Intel PT and saves its registers
using pt_event_stop(), which is also used by pmu.stop handler.
This function stops Intel PT on the CPU where it is working, therefore
users of it need to call it for each CPU to stop all logging.
Signed-off-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin<alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: H.Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Vivek Goyal <vgoyal@redhat.com>
Link: http://lkml.kernel.org/r/1446614553-6072-2-git-send-email-indou.takao@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With LBRv5 reading the extra LBR flags like mispredict, TSX, cycles is
not free anymore, as it has moved to a separate MSR.
For callstack mode we don't need any of this information; so we can
avoid the unnecessary MSR read. Add flags to the perf interface where
perf record can request not collecting this information.
Add branch_sample_type flags for CYCLES and FLAGS. It's a bit unusual
for branch_sample_types to be negative (disable), not positive (enable),
but since the legacy ABI reported the flags we need some form of
explicit disabling to avoid breaking the ABI.
After we have the flags the x86 perf code can keep track if any users
need the flags. If noone needs it the information is not collected.
This cuts down the cost of LBR callstack on Skylake significantly.
Profiling a kernel build with LBR call stack the average run time of
the PMI handler drops by 43%.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Cc: jolsa@kernel.org
Link: http://lkml.kernel.org/r/1445366797-30894-2-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Change the perf user stack walking to use the new
__copy_from_user_nmi(), and split each access into word sized transfer
sizes. This allows to inline the complete access and optimize it all
into a single load.
The main advantage is that this avoids the overhead of double page
faults. When normal copy_from_user() fails it reexecutes the copy to
compute an accurate number of non copied bytes. This leads to
executing the expensive page fault twice.
While walking stacks having a fault at some point is relatively common
(typically when some part of the program isn't compiled with frame
pointers), so this is a large overhead.
With the optimized copies we avoid this problem because they only do
all accesses once. And of course they're much faster too when the
access does not fault because they're just single instructions instead
of complex function calls.
While profiling a kernel build with -g, the patch brings down the
average time of the PMI handler from 966ns to 552ns (-43%).
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1445551641-13379-2-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There were still a number of references to my old Red Hat email
address in the kernel source. Remove these while keeping the
Red Hat copyright notices intact.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This fixes a bug I added in the following commit:
90405aa022 ("perf/x86/intel/lbr: Limit LBR accesses to TOS in callstack mode")
The bug could lead to lost LBR call stacks. When restoring the LBR state
we need to use the TOS of the previous context, not the current context.
To do that we need to save/restore the TOS.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Cc: jolsa@kernel.org
Link: http://lkml.kernel.org/r/1445366797-30894-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch reinforces the lockdep checks performed by
perf_cgroup_from_tsk() by passing the perf_event_context
whenever possible. It is okay to not hold the RCU read lock
when we know we hold the ctx->lock. This patch makes sure this
property holds.
In some functions, such as perf_cgroup_sched_in(), we do not
pass the context because we are sure we are holding the RCU
read lock.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: edumazet@google.com
Link: http://lkml.kernel.org/r/1447322404-10920-3-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- MPX updates for handling 32bit processes
- A fix for a long standing bug in 32bit signal frame handling
related to FPU/XSAVE state
- Handle get_xsave_addr() correctly in KVM
- Fix SMAP check under paravirtualization
- Add a comment to the static function trace entry to avoid further
confusion about the difference to dynamic tracing"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix SMAP check in PVOPS environments
x86/ftrace: Add comment on static function tracing
x86/fpu: Fix get_xsave_addr() behavior under virtualization
x86/fpu: Fix 32-bit signal frame handling
x86/mpx: Fix 32-bit address space calculation
x86/mpx: Do proper get_user() when running 32-bit binaries on 64-bit kernels
There appears to be no formal statement of what pv_irq_ops.save_fl() is
supposed to return precisely. Native returns the full flags, while lguest and
Xen only return the Interrupt Flag, and both have comments by the
implementations stating that only the Interrupt Flag is looked at. This may
have been true when initially implemented, but no longer is.
To make matters worse, the Xen PVOP leaves the upper bits undefined, making
the BUG_ON() undefined behaviour. Experimentally, this now trips for 32bit PV
guests on Broadwell hardware. The BUG_ON() is consistent for an individual
build, but not consistent for all builds. It has also been a sitting timebomb
since SMAP support was introduced.
Use native_save_fl() instead, which will obtain an accurate view of the AC
flag.
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: <lguest@lists.ozlabs.org>
Cc: Xen-devel <xen-devel@lists.xen.org>
CC: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1433323874-6927-1-git-send-email-andrew.cooper3@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull perf updates from Thomas Gleixner:
"Mostly updates to the perf tool plus two fixes to the kernel core code:
- Handle tracepoint filters correctly for inherited events (Peter
Zijlstra)
- Prevent a deadlock in perf_lock_task_context (Paul McKenney)
- Add missing newlines to some pr_err() calls (Arnaldo Carvalho de
Melo)
- Print full source file paths when using 'perf annotate --print-line
--full-paths' (Michael Petlan)
- Fix 'perf probe -d' when just one out of uprobes and kprobes is
enabled (Wang Nan)
- Add compiler.h to list.h to fix 'make perf-tar-src-pkg' generated
tarballs, i.e. out of tree building (Arnaldo Carvalho de Melo)
- Add the llvm-src-base.c and llvm-src-kbuild.c files, generated by
the 'perf test' LLVM entries, when running it in-tree, to
.gitignore (Yunlong Song)
- libbpf error reporting improvements, using a strerror interface to
more precisely tell the user about problems with the provided
scriptlet, be it in C or as a ready made object file (Wang Nan)
- Do not be case sensitive when searching for matching 'perf test'
entries (Arnaldo Carvalho de Melo)
- Inform the user about objdump failures in 'perf annotate' (Andi
Kleen)
- Improve the LLVM 'perf test' entry, introduce a new ones for BPF
and kbuild tests to check the environment used by clang to compile
.c scriptlets (Wang Nan)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
perf/x86/intel/rapl: Remove the unused RAPL_EVENT_DESC() macro
tools include: Add compiler.h to list.h
perf probe: Verify parameters in two functions
perf session: Add missing newlines to some pr_err() calls
perf annotate: Support full source file paths for srcline fix
perf test: Add llvm-src-base.c and llvm-src-kbuild.c to .gitignore
perf: Fix inherited events vs. tracepoint filters
perf: Disable IRQs across RCU RS CS that acquires scheduler lock
perf test: Do not be case sensitive when searching for matching tests
perf test: Add 'perf test BPF'
perf test: Enhance the LLVM tests: add kbuild test
perf test: Enhance the LLVM test: update basic BPF test program
perf bpf: Improve BPF related error messages
perf tools: Make fetch_kernel_version() publicly available
bpf tools: Add new API bpf_object__get_kversion()
bpf tools: Improve libbpf error reporting
perf probe: Cleanup find_perf_probe_point_from_map to reduce redundancy
perf annotate: Inform the user about objdump failures in --stdio
perf stat: Make stat options global
perf sched latency: Fix thread pid reuse issue
...
Pull x86 fixes from Thomas Gleixner:
"A couple of fixes and updates related to x86:
- Fix the W+X check regression on XEN
- The real fix for the low identity map trainwreck
- Probe legacy PIC early instead of unconditionally allocating legacy
irqs
- Add cpu verification to long mode entry
- Adjust the cache topology to AMD Fam17H systems
- Let Merrifield use the TSC across S3"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Call verify_cpu() after having entered long mode too
x86/setup: Fix low identity map for >= 2GB kernel range
x86/mm: Skip the hypervisor range when walking PGD
x86/AMD: Fix last level cache topology for AMD Fam17h systems
x86/irq: Probe for PIC presence before allocating descs for legacy IRQs
x86/cpu/intel: Enable X86_FEATURE_NONSTOP_TSC_S3 for Merrifield
On AMD Fam17h systems, the last level cache is not resident in the
northbridge. Therefore, we cannot assign cpu_llc_id to the same value as
Node ID as we have been doing until now.
We should rather look at the ApicID bits of the core to provide us the
last level cache ID info.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jacob Shin <jacob.w.shin@gmail.com>
Link: http://lkml.kernel.org/r/1446582899-9378-1-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Intel Merrifield SoC is a successor of the Intel MID line of
SoCs. Let's set the neccessary capability for that chip. See commit
c54fdbb282 (x86: Add cpu capability flag X86_FEATURE_NONSTOP_TSC_S3)
for the details.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: http://lkml.kernel.org/r/1444319786-36125-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull x86 cpu changes from Ingo Molnar:
"Two changes in this cycle: a Kconfig help text enhancement, and an AMD
CLZERO instruction capability detection and enumeration"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add CLZERO detection
x86/Kconfig/cpus: Fix/complete CPU type help texts
Pull RAS changes from Ingo Molnar:
"The main system reliability related changes were from x86, but also
some generic RAS changes:
- AMD MCE error injection subsystem enhancements. (Aravind
Gopalakrishnan)
- Fix MCE and CPU hotplug interaction bug. (Ashok Raj)
- kcrash bootup robustness fix. (Baoquan He)
- kcrash cleanups. (Borislav Petkov)
- x86 microcode driver rework: simplify it by unmodularizing it and
other cleanups. (Borislav Petkov)"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/mce: Add a default case to the switch in __mcheck_cpu_ancient_init()
x86/mce: Add a Scalable MCA vendor flags bit
MAINTAINERS: Unify the microcode driver section
x86/microcode/intel: Move #ifdef DEBUG inside the function
x86/microcode/amd: Remove maintainers from comments
x86/microcode: Remove modularization leftovers
x86/microcode: Merge the early microcode loader
x86/microcode: Unmodularize the microcode driver
x86/mce: Fix thermal throttling reporting after kexec
kexec/crash: Say which char is the unrecognized
x86/setup/crash: Check memblock_reserve() retval
x86/setup/crash: Cleanup some more
x86/setup/crash: Remove alignment variable
x86/setup: Cleanup crashkernel reservation functions
x86/amd_nb, EDAC: Rename amd_get_node_id()
x86/setup: Do not reserve crashkernel high memory if low reservation failed
x86/microcode/amd: Do not overwrite final patch levels
x86/microcode/amd: Extract current patch level read to a function
x86/ras/mce_amd_inj: Inject bank 4 errors on the NBC
x86/ras/mce_amd_inj: Trigger deferred and thresholding errors interrupts
...
AMD Fam17h processors introduce support for the CLZERO
instruction. It zeroes out the 64 byte cache line specified in
RAX.
Add the bit here to allow /proc/cpuinfo to list the feature.
Boris: we're adding this as a separate ->x86_capability leaf
because CPUID_80000008_EBX is going to contain more feature bits
and it will fill out with time.
Signed-off-by: Wan Zongshun <Vincent.Wan@amd.com>
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
[ Wrap code in patch form, fix comments. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1446207099-24948-4-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Scalable MCA (SMCA) is a new feature in AMD Fam17h processors
which indicates presence of MCA extensions.
MCA extensions expands existing register space for the MCE banks
and also introduces a new MSR range to accommodate new banks.
Add the detection bit.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
[ Reformat mce_vendor_flags definitions and save indentation levels. Improve comments. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1446207099-24948-2-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
... and save us the stub.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1445334889-300-6-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have the MAINTAINERS file for that. Also, Andreas doesn't
have the time for this work anymore.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1445334889-300-5-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove the remaining module functionality leftovers. Make
"dis_ucode_ldr" an early_param and make it static again. Drop
module aliases, autoloading table, description, etc.
Bump version number, while at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1445334889-300-4-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge the early loader functionality into the driver proper. The
diff is huge but logically, it is simply moving code from the
_early.c files into the main driver.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1445334889-300-3-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Make CONFIG_MICROCODE a bool. It was practically a bool already anyway,
since early loader was forcing it to =y.
Regardless, there's no real reason to have something be a module which
gets built-in on the majority of installations out there. And its not
like there's noticeable change in functionality - we still can load late
microcode - just the module glue disappears.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1445334889-300-2-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The per CPU thermal vector init code checks if the thermal
vector is already installed and complains and bails out if it
is.
This happens after kexec, as kernel shut down does not clear the
thermal vector APIC register.
This causes two problems:
1. So we always do not fully initialize thermal reports after
kexec. The CPU is still likely initialized, as the previous
kernel should have done it. But we don't set up the software
pointer to the thermal vector, so reporting may end up with a
unknown thermal interrupt message.
2. Also it complains for every logical CPU, even though the
value is actually derived from BP only.
The problem is that we end up with one message per CPU, so on
larger systems it becomes very noisy and messes up the otherwise
nicely formatted CPU bootup numbers in the kernel log.
Just remove the check. I checked the code and there's no valid
code paths where the thermal init code for a CPU could be called
multiple times.
Why the kernel does not clean up this value on shutdown:
The thermal monitoring is controlled per logical CPU thread.
Normal shutdown code is just running on one CPU. To disable it
we would need a broadcast NMI to all CPUs on shut down. That's
overkill for this. So we just ignore it after kexec.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1445246268-26285-9-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch enables the suport for the PERF_SAMPLE_BRANCH_CALL
for Intel x86 processors. When the processor support LBR filtering
this the selection is done in hardware. Otherwise, the filter is
applied by software. Note that we chose to include zero length calls
because they also represent calls.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: khandual@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1444720151-10275-3-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A certain number of patch levels of applied microcode should not
be overwritten by the microcode loader, otherwise bad things
will happen.
Check those and abort update if the current core has one of
those final patch levels applied by the BIOS. 32-bit needs
special handling, of course.
See https://bugzilla.suse.com/show_bug.cgi?id=913996 for more
info.
Tested-by: Peter Kirchgeßner <pkirchgessner@t-online.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1444641762-9437-7-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pave the way for checking the current patch level of the
microcode in a core. We want to be able to do stuff depending on
the patch level - in this case decide whether to update or not.
But that will be added in a later patch.
Drop unused local var uci assignment, while at it.
Integrate a fix for 32-bit and CONFIG_PARAVIRT from Takashi Iwai:
Use native_rdmsr() in check_current_patch_level() because with
CONFIG_PARAVIRT enabled and on 32-bit, where we run before
paging has been enabled, we cannot deref pv_info yet. Or we
could, but we'd need to access its physical address. This way of
fixing it is simpler. See:
https://bugzilla.suse.com/show_bug.cgi?id=943179 for the background.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Takashi Iwai <tiwai@suse.com>:
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1444641762-9437-6-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In multi-segment system, uncore devices may belong to buses whose segment
number is other than 0:
....
0000:ff:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03)
...
0001:7f:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03)
...
0001:bf:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03)
...
0001:ff:10.5 System peripheral: Intel Corporation Xeon E5 v3/Core i7 Scratchpad & Semaphore Registers (rev 03
...
In that case, relation of bus number and physical id may be broken
because "uncore_pcibus_to_physid" doesn't take account of PCI segment.
For example, bus 0000:ff and 0001:ff uses the same entry of
"uncore_pcibus_to_physid" array.
This patch fixes this problem by introducing the segment-aware pci2phy_map instead.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: hpa@zytor.com
Link: http://lkml.kernel.org/r/1443096621-4119-1-git-send-email-izumi.taku@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds new PMUs to support cstate related free running
(read-only) counters. These counters may be used simultaneously by other
tools, such as turbostat. However, it still make sense to implement them
in perf. Because we can conveniently collect them together with other
events, and allow to use them from tools without special MSR access
code.
These counters include CORE_C*_RESIDENCY and PKG_C*_RESIDENCY.
According to counters' scope and category, two PMUs are registered with
the perf_event core subsystem.
- 'cstate_core': The counter is available for each physical core. The
counters include CORE_C*_RESIDENCY.
- 'cstate_pkg': The counter is available for each physical package. The
counters include PKG_C*_RESIDENCY.
The events are exposed in sysfs for use by perf stat and other tools.
The files are:
/sys/devices/cstate_core/events/c*-residency
/sys/devices/cstate_pkg/events/c*-residency
These events only support system-wide mode counting.
The /sys/devices/cstate_*/cpumask file can be used by tools to figure
out which CPUs to monitor by default.
The PMU type (attr->type) is dynamically allocated and is available from
/sys/devices/core_misc/type and /sys/device/cstate_*/type.
Sampling is not supported.
Here is an example.
- To caculate the fraction of time when the core is running in C6 state
CORE_C6_time% = CORE_C6_RESIDENCY / TSC
# perf stat -x, -e"cstate_core/c6-residency/,msr/tsc/" -C0 -- taskset -c 0 sleep 5
11838820015,,cstate_core/c6-residency/,5175919658,100.00
11877130740,,msr/tsc/,5175922010,100.00
For sleep, 99.7% of time we ran in C6 state.
# perf stat -x, -e"cstate_core/c6-residency/,msr/tsc/" -C0 -- taskset -c 0 busyloop
1253316,,cstate_core/c6-residency/,4360969154,100.00
10012635248,,msr/tsc/,4360972366,100.00
For busyloop, 0.01% of time we ran in C6 state.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/1443443404-8581-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 fixes from Ingo Molnar:
"Fixes all around the map: W+X kernel mapping fix, WCHAN fixes, two
build failure fixes for corner case configs, x32 header fix and a
speling fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/headers/uapi: Fix __BITS_PER_LONG value for x32 builds
x86/mm: Set NX on gap between __ex_table and rodata
x86/kexec: Fix kexec crash in syscall kexec_file_load()
x86/process: Unify 32bit and 64bit implementations of get_wchan()
x86/process: Add proper bound checks in 64bit get_wchan()
x86, efi, kasan: Fix build failure on !KASAN && KMEMCHECK=y kernels
x86/hyperv: Fix the build in the !CONFIG_KEXEC_CORE case
x86/cpufeatures: Correct spelling of the HWP_NOTIFY flag
The DEFINE_PCI_DEVICE_TABLE() macro is deprecated. Use
'struct pci_device_id' instead of DEFINE_PCI_DEVICE_TABLE(),
with the goal of getting rid of this macro completely.
This Coccinelle semantic patch performs this transformation:
@@
identifier a;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer i;
@@
- DEFINE_PCI_DEVICE_TABLE(a)
+ const struct pci_device_id a[] = i;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20151001085201.GA16939@localhost
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Recent changes in the Hyper-V driver:
b4370df2b1 ("Drivers: hv: vmbus: add special crash handler")
broke the build when CONFIG_KEXEC_CORE is not set:
arch/x86/built-in.o: In function `hv_machine_crash_shutdown':
arch/x86/kernel/cpu/mshyperv.c:112: undefined reference to `native_machine_crash_shutdown'
Decorate all kexec related code with #ifdef CONFIG_KEXEC_CORE.
Reported-by: Jim Davis <jim.epost@gmail.com>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: devel@linuxdriverproject.org
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1443002577-25370-1-git-send-email-vkuznets@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is not safe to clear global MCi_CTL banks during CPU offline
or suspend/resume operations. These MSRs are either
thread-scoped (meaning private to a thread), or core-scoped
(private to threads in that core only), or with a socket scope:
visible and controllable from all threads in the socket.
When we offline a single CPU, clearing those MCi_CTL bits will
stop signaling for all the shared, i.e., socket-wide resources,
such as LLC, iMC, etc.
In addition, it might be possible to compromise the integrity of
an Intel Secure Guard eXtentions (SGX) system if the attacker
has control of the host system and is able to inject errors
which would be otherwise ignored when MCi_CTL bits are cleared.
Hence on SGX enabled systems, if MCi_CTL is cleared, SGX gets
disabled.
Tested-by: Serge Ayoun <serge.ayoun@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
[ Cleanup text. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1441391390-16985-1-git-send-email-ashok.raj@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
