In case of duplex mode (capture and playback at the same time), the second
stream has to have the same parameters (rate, sample size) as the already
running stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
TWL4030 supports 96KHz sample playback, but only playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Optimize the display of SSI statistics in the Freescale MPC8610 sound driver
to display the status count only of the interrupts that were actually enabled.
Previously, it would display the counts of all SISR status bits, even those
that were not enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
the variable gsr_bit is set in isr. It is however set to 0 and interrupts are
disabled prior to reset. Hence it doesn't make a lot of sense to show the
content of gsr_bit in case of a reset timeout.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove the delay from the trigger function in the Freescale MPC8610 sound
driver when capture is started. This delay was used to ensure that the DMA
controller was active when ALSA call the .pointer function to request a
DMA transfer status. A better approach is for the .pointer function to detect
that DMA has not started, and return zero instead. This change eliminates
the need for the delay.
Also add some related code to check for a DMA programming error, and report
XRUN if it occurs.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
HTC Magician has a Philips UDA1380 codec connected via
SSP1 (playback) and I2S (capture).
There is a flip-flop between the SSP frame clock output
and the codec's word select input pin. To make the codec
see proper I2S input, the SSP has to send two frames per
sample.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now magician and similar boards can use network mode with only one
active slot to explicitly set 16 bit frame width, even for S16_LE
stereo sound.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Headset was declared previously as a Headphone widget connecting
HSMIC and HSOL/HSOR pins of TWL4030 codec in SDP430 machine driver.
The capture path becomes invalid as the Headphone widget is not a
valid input endpoint.
Instead of that, the Headset is declared as separate Microphone
and Headphone widgets. Current patch modifies audio map:
- Headset Mic: HSMIC with bias
- Headset Stereophone: HSOL, HSOR
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add functions "Headset" and "Mic" to the control "Jack Function" for
activating and de-activating codec input pin LINE1L which is connected to
the mic pin of 4-pole Nokia AV connecter.
Note there is no mic bias voltage management here since bias is coming from
Nokia ASIC and driver for it is not in mainline.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is an AVDD supply as well, normally one or more of the other
upplies would be tied to it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The active discharge does not bring sufficient benefit to justify the
lengthy times involved so don't do that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit 14fa43f53f ("ASoC: Only
register AC97 bus if it's not done already") added a condition for
calling of soc_ac97_dev_register() but not added for calling of
soc_ac97_dev_unregister(). This patch adds same condition for
soc_ac97_dev_unregister(). Without this fix, kernel crashes when
unloading an asoc driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC sound/soc/codecs/twl4030.o
sound/soc/codecs/twl4030.c:1400: warning: braces around scalar initializer
sound/soc/codecs/twl4030.c:1400: warning: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1401: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1401: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1401: warning: initialization from incompatible pointer type
sound/soc/codecs/twl4030.c:1402: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1402: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1402: warning: excess elements in scalar initializer
sound/soc/codecs/twl4030.c:1402: warning: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1403: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1403: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1403: warning: excess elements in scalar initializer
sound/soc/codecs/twl4030.c:1403: warning: (near initialization for 'twl4030_dai.ops')
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As the PXA27x series allow 2 gpios to reset the ac97 bus,
allow through platform data configuration the definition of
the correct gpio which will reset the AC97 bus.
This comes from a silicon defect on the PXA27x series, where
the gpio must be manually controlled in warm reset cases.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Two issues are fixed here:
- I2S transmits the left frame with the clock low but I don't seem to
get LRCLK out without SFRMDLY being set so invert SFRMP and set a
delay.
- I2S has a clock cycle prior to the first data byte in each channel
so we need to delay the data by one cycle.
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This switches the pxa ssp port usage from network mode to PSP mode.
Removed some comments and checks for configured TDM channels.
A special case is added to support configuration where BCLK = 64fs. We
need to do some black magic in this case which doesn't look nice but
there is unfortunately no other option than that.
Diagnosed-by: Tim Ruetz <tim@caiaq.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move headset jack registration to the codec/machine specific
initialization. Having the jack registration in machine init
causes that the jack device gets initialized but not registered
since the sound card is registered before the jack. Moving jack
registration to device initialization will register the jack
device along with all other devices associated to the card when
the card is registed. As a consequence of jack device registered
properly, the jack is detected as an input device.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The drivers are basically duplicating the same code over and over.
As snd_soc_cnew is going to be made static some time after the next
merge window, we might as well convert them now.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Refactor the WM8580 device registration to probe via standard I2C device
registration, registering the DAIs once the device has probed via I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge Eric Maio's patch to merge snd_soc_dai_ops out of line. Fixed
merge issues and updated drivers, plus an issue with the ops for the two
s3c2443 AC97 DAIs having been merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8400 is a highly integrated audio CODEC and power management unit
intended for mobile multimedia application. This driver supports the
primary audio CODEC features, including:
- 1W speaker driver
- Fully differential headphone output
- Up to 4 differential microphone inputs
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Buildfix:
CC sound/soc/omap/osk5912.o
sound/soc/omap/osk5912.c: In function 'osk_soc_init':
sound/soc/omap/osk5912.c:189: error: implicit declaration of function 'clk_get_usecount'
make[3]: *** [sound/soc/omap/osk5912.o] Error 1
There's no such (standard) clock interface.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These changes were included in the S3C audio header move but are not
directly related to it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In pxa_ssp_set_dai_fmt(), check whether there is anything to do at all.
If there would be but the SSP port is in use already, bail out.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The definitions of S3C2412_IISMOD_SDF_MSB and S3C2412_IISMOD_SDF_LSB
are incorrect, being the same S3C2412_IISMOD_SDF_IIS which is the
only correct one in this series.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will break any boards that don't register the AC97 controller
device due to using ASoC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds a driver for the SPI connected AK4104 S/PDIF transmitter
device. Its features are fairly simple, but as there is need to set up
certain bits in the IEC958 information, this better goes into a real
driver.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Removes numbers from the list of features/limitations and makes it
reflect recent changes to the code.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for true pause and unpause. Without this, mplayer will drop some
audio (less than one second, but still noticeable) when pausing playback.
Remove support for PM suspend and resume from the trigger function, since the
driver doesn't support PM anyway.
Optimize the delay after starting capture. Instead of delaying 1ms, the driver
now polls the hardware. The new delay is shorter by over 90% yet still
effective.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Upgrade the severity of some failure messages from debug level so
they're displayed by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
