Different hardware device Ids correspond to different maximum speed
available. Extra checks were added for devices D108 and D109 to
remove unsupported speeds from these device capabilities list.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware flashing takes around 60s (specified to not take more than
70s). Prevent hogging the RTNL lock in this time and make use of the
longer timeout for the NSP command. The timeout is set to 2.5 * 70
seconds.
We only allow flashing the firmware from reprs or PF netdevs. VFs do not
have an app reference.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware flashing NSP operation takes longer to execute than the
current default timeout. We need a mechanism to set a longer timeout for
some commands. This patch adds the infrastructure to this.
The default timeout is still 30 seconds.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All PF mailbox events are conveyed through a common interrupt
(vector 0). This interrupt vector is shared by reset and mailbox.
This patch adds the handling of mailbox interrupt event and its
deferred processing in context to a separate mailbox task.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is required to support ring-vector binding and reset
of TQPs requested by the VF driver to the PF driver. Mailbox
handler is added with corresponding VF commands/messages to
handle the request.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command queue provides the provision of Mailbox command which
can be used for communication between PF and VF. PF handles
messages from various VFs for fetching various information like,
queue, vlan, link status related etc. It also handles the request
from various VFs to perform certain privileged operations.
This patch adds the support of a message handler for handling
such various command requests from VF.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the NAPI handling interface, skb buffer management,
management of the RX/TX descriptors, ethool interface etc.
has quite a bit of code which is common to VF and PF driver.
This patch makes the exisitng PF's HNS3 ENET driver as the
common ENET driver for both Virtual & Physical Function. This
will help in reduction of redundancy and better management of
code.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the new Makefiles and updates existing
Makefiles required to build the HNS3 Virtual Function driver.
This also updates the Kconfig for introduction of new menuconfig
entries related to VF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of hardware compatibiltiy layer to the
HNS3 VF Driver. This layer implements various {set|get} operations
over MAC address for a virtual port, RSS related configuration,
fetches the link status info from PF, does various VLAN related
configuration over the virtual port, queries the statistics from
the hardware etc.
This layer can directly interact with hardware through the
IMP(Integrated Mangement Processor) interface or can use mailbox
to interact with the PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of the mailbox to the VF driver. The
mailbox shall be used as an interface to communicate with the
PF driver for various purposes like {set|get} MAC related
operations, reset, link status etc. The mailbox supports both
synchronous and asynchronous command send to PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of command interface for communication with
the IMP(Integrated Management Processor) for HNS3 Virtual Function
Driver.
Each VF has support of CQP(Command Queue Pair) ring interface.
Each CQP consis of send queue CSQ and receive queue CRQ.
There are various commands a VF may support, like to query frimware
version, TQP management, statistics, interrupt related, mailbox etc.
This also contains code to initialize the command queue, manage the
command queue descriptors and Rx/Tx protocol with the command processor
in the form of various commands/results and acknowledgements.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Learning is currently enabled for ports which are OVS slaves -
even though OVS doesn't need this indication.
Since we're not associating a fid with the port, HW would continuously
notify driver of learned [& aged] MACs which would be logged as errors.
Fixes: 2b94e58df5 ("mlxsw: spectrum: Allow ports to work under OVS master")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the program is simple and has only one adjust head call
with constant parameters, we can check that the call will
always succeed at translation time. We need to track the
location of the call and make sure parameters are always
the same. We also have to check the parameters against
datapath constraints and ETH_HLEN.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Support bpf_xdp_adjust_head(). We need to check whether the
packet offset after adjustment is within datapath's limits.
We also check if the frame is at least ETH_HLEN long (similar
to the kernel implementation).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add skeleton of verifier checks and translation handler
for call instructions. Make sure jump target resolution
will not treat them as jumps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
BPF FW creates a run time symbol called bpf_capabilities which
contains TLV-formatted capability information. Allocate app
private structure to store parsed capabilities and add a skeleton
of parsing logic.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Allow users outside of core reading area sizes. This was not needed
previously because whatever entity created the area would usually know
what size it asked for. The nfp_rtsym_map() helper, however, will
allocate the area based on the size of an RT-symbol with given name.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Before this patch, the stats_lock was acquired twice. In between the
locks Driver sent command to gather some more statistics (per priority
and counter statistics). If the stats lock was acquired by get
statistics NDO in between we would have report out of sync counters.
Fix this by collecting all stats from Firmware in advance and then
fill the Software structs under one lock.
Fixes: 0b131561a7 ("net/mlx4_en: Add Flow control statistics display via ethtool")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field res_free indicates the total number of counters which are
available for allocation (reserved and unreserved). Fixed a bug where
the reserved counters were subtracted from res_free before any
allocation was performed.
Before this fix, free counters which were not reserved could not be
allocated.
Fixes: 9de92c60be ("net/mlx4_core: Adjust counter grant policy in the resource tracker")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the minimal MTU threshold for running loopback selftest.
MTU should be big enough to include packet payload, NET_IP_ALIGN,
Ethernet headers and preamble length.
Fixes: e7c1c2c462 ("mlx4_en: Added self diagnostics test implementation")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not correct to return NULL when that is actually an error and
function returns errors in any other wrong case. In the same time,
the cpsw driver and davinci emac doesn't check error case while
creating channel and it can miss actual error. Also remove WARNs
replacing them on dev_err msgs.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for ethtool get_module_info() and get_module_eeprom()
callbacks that will dump necessary information for a SFP.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to handle multi-port SKGE boards was freeing IRQ
twice. The first one was under lock and might sleep.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_napi_del is called implicitely by free_netdev, therefore we
don't have to do it explicitely.
When the probe error path is reached, the net_device isn't
registered yet. Therefore reordering the call to netif_napi_del
shouldn't cause any issues.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify probe error path and remove callback by using device-managed
functions.
rtl_disable_msi isn't needed any longer because the release callback
of pcim_enable_device does this implicitely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an option to configure the mux id, aggregation and commad feature
for existing rmnet devices. Implement the changelink netlink
operation for this.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an option to configure the rmnet aggregation and command features
on device creation. This is achieved by using the vlan flags option.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to send and receive packets over ethernet.
An example of usage is testing the data path on UML. This can be
achieved by setting up two UML instances in multicast mode and
associating rmnet over the UML ethernet device.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon de-multiplexing data from one real dev, the packets can be sent
to an unique rmnet device for a given mux id.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiplexing is always enabled when transmiting from a rmnet device,
so remove the redundant egress macros. De-multiplexing is always
enabled when receiving packets from a rmnet device, so remove those
ingress macros.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the success and consumed entries were actually in use.
Use standard error codes instead.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Changes since v2 [1]:
* Merged with latest code changes
Changes since v1:
Update made thanks to David's review, much appreciated David.
* Improved inconsistent failure handling of clock rate setting
* For completeness of usecase, added arc_emac_probe error handling
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs (for example the SMSC LAN8710/LAN8720) doesn't allow turning
the refclk on and off again during operation (according to their
datasheet). Nonetheless exactly this behaviour was introduced for power
saving reasons by commit e8fcfcd568 ("net: fec: optimize the clock management to save power").
Therefore add support for the phy_reset_after_clk_enable function from
phylib to mitigate this issue.
Generally speaking this issue is only relevant if the ref clk for the
PHY is generated by the SoC and therefore the PHY is configured to
"REF_CLK In Mode". In our specific case (PCB) this problem does occur at
about every 10th to 50th POR of an LAN8710 connected to an i.MX6SOLO
SoC. The typical symptom of this problem is a "swinging" ethernet link.
Similar issues were reported by users of the NXP forum:
https://community.nxp.com/thread/389902https://community.nxp.com/message/309354
With this patch applied the issue didn't occur for at least a few
hundret PORs of our board.
Fixes: e8fcfcd568 ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fbf3d034f2.
As of commit 560869100b ("clk: renesas: cpg-mssr: Restore module
clocks during resume"), the workaround is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adjust the coalescing parameters to the vendor
recommendations for the PPv2 network controller.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the tx-usec value to the informations reported to
ethtool by the get_coalesce function.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch aligning values in the ethtool get_coalesce function.
This patch do not modify in anyway the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx/Tx ring sizes can be adjusted thanks to ethtool given specific
network needs. This commit splits the default ring size from its max
value to allow ethtool to vary the parameters in both ways.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check to only free the TSO header buffer when its
allocation previously succeeded.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both tx_ring and first_tx are the head of tx ring, it not
necessary to use two structure members to statically indicate
the head of tx ring. So first_tx is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the requested dump level parameter to big-endian at the start of
nfp_net_dump_calculate_size() and nfp_net_dump_populate_buffer(), then
compare and assign it directly where needed in the traversal and prolog
code. This decreases the total number of conversions used.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete match field defines that are not supported at this time.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port matching is selected by default on every rule so remove check for it
and delete 'else' side of the statement. Remove nfp_flower_meta_one as now
it will not feature in the code. Rename nfp_flower_meta_two given that one
has been removed.
'Additional metadata' if statement can never be true so remove it as well.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the matching of mac/mpls as a default selection. These are not
necessarily set by a TC rule (unlike the port). Previously a mac/mpls
field would exist in every match and be masked out if not used. This patch
has no impact on functionality but removes unnessary memory assignment in
the match cmsg.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all variants of the sh_eth hardware have Gigabit
support. Unfortunately, the current driver doesn't tell the PHY about
the limited MAC capabilities. Due to this, if you have a Gigabit
capable PHY, the PHY will advertise its Gigabit capability and
establish a link at 1Gbit/s, even though the MAC doesn't support it.
In order to avoid this, we use the recently introduced
phy_set_max_speed() to tell the PHY to not advertise speed higher than
100 MBit/s.
Tested on a SH7786 platform, with a Gigabit PHY.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.
Fixes: 1d7d15d79f ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use meminfo to identify the egress and ingress context regions and
fetch all valid contexts from those regions. Also flush all contexts
before attempting collection to prevent stale information.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use meminfo to identify TX and RX payload regions and skip them in
collection of EDC, MC, and HMA.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use meminfo to get base address and size of MC memory. Also use same
meminfo for EDC memory dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect memory layout of various on-chip memory regions. Move code
for collecting on-chip memory information to cudbg_lib.c and update
cxgb4_debugfs.c to use the common function. Also include
cudbg_entity.h before cudbg_lib.h to avoid adding cudbg entity
structure forward declarations in cudbg_lib.h.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing that says that number of TX queues == number of RX
queues. E.g. the ARTPEC-6 SoC has 2 TX queues and 1 RX queue.
This code is obviously wrong:
for (chan = 0; chan < tx_channel_count; chan++) {
struct stmmac_rx_queue *rx_q = &priv->rx_queue[chan];
priv->rx_queue has size MTL_MAX_RX_QUEUES, so this will send an
uninitialized napi_struct to __napi_schedule(), causing us to
crash in net_rx_action(), because napi_struct->poll is zero.
[12846.759880] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[12846.768014] pgd = (ptrval)
[12846.770742] [00000000] *pgd=39ec7831, *pte=00000000, *ppte=00000000
[12846.777023] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[12846.782942] Modules linked in:
[12846.785998] CPU: 0 PID: 161 Comm: dropbear Not tainted 4.15.0-rc2-00285-gf5fb5f2f39a7 #36
[12846.794177] Hardware name: Axis ARTPEC-6 Platform
[12846.798879] task: (ptrval) task.stack: (ptrval)
[12846.803407] PC is at 0x0
[12846.805942] LR is at net_rx_action+0x274/0x43c
[12846.810383] pc : [<00000000>] lr : [<80bff064>] psr: 200e0113
[12846.816648] sp : b90d9ae8 ip : b90d9ae8 fp : b90d9b44
[12846.821871] r10: 00000008 r9 : 0013250e r8 : 00000100
[12846.827094] r7 : 0000012c r6 : 00000000 r5 : 00000001 r4 : bac84900
[12846.833619] r3 : 00000000 r2 : b90d9b08 r1 : 00000000 r0 : bac84900
Since each DMA channel can be used for rx and tx simultaneously,
the current code should probably be rewritten so that napi_struct is
embedded in a new struct stmmac_channel.
That way, stmmac_poll() can call stmmac_tx_clean() on just the tx queue
where we got the IRQ, instead of looping through all tx queues.
This is also how the xgbe driver does it (another driver for this IP).
Fixes: c22a3f48ef ("net: stmmac: adding multiple napi mechanism")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After applying 2270bc5da3 ("bnxt_en: Fix netpoll handling") and
903649e718 ("bnxt_en: Improve -ENOMEM logic in NAPI poll loop."),
we still see the following WARN fire:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1875170 at net/core/netpoll.c:165 netpoll_poll_dev+0x15a/0x160
bnxt_poll+0x0/0xd0 exceeded budget in poll
<snip>
Call Trace:
[<ffffffff814be5cd>] dump_stack+0x4d/0x70
[<ffffffff8107e013>] __warn+0xd3/0xf0
[<ffffffff8107e07f>] warn_slowpath_fmt+0x4f/0x60
[<ffffffff8179519a>] netpoll_poll_dev+0x15a/0x160
[<ffffffff81795f38>] netpoll_send_skb_on_dev+0x168/0x250
[<ffffffff817962fc>] netpoll_send_udp+0x2dc/0x440
[<ffffffff815fa9be>] write_ext_msg+0x20e/0x250
[<ffffffff810c8125>] call_console_drivers.constprop.23+0xa5/0x110
[<ffffffff810c9549>] console_unlock+0x339/0x5b0
[<ffffffff810c9a88>] vprintk_emit+0x2c8/0x450
[<ffffffff810c9d5f>] vprintk_default+0x1f/0x30
[<ffffffff81173df5>] printk+0x48/0x50
[<ffffffffa0197713>] edac_raw_mc_handle_error+0x563/0x5c0 [edac_core]
[<ffffffffa0197b9b>] edac_mc_handle_error+0x42b/0x6e0 [edac_core]
[<ffffffffa01c3a60>] sbridge_mce_output_error+0x410/0x10d0 [sb_edac]
[<ffffffffa01c47cc>] sbridge_check_error+0xac/0x130 [sb_edac]
[<ffffffffa0197f3c>] edac_mc_workq_function+0x3c/0x90 [edac_core]
[<ffffffff81095f8b>] process_one_work+0x19b/0x480
[<ffffffff810967ca>] worker_thread+0x6a/0x520
[<ffffffff8109c7c4>] kthread+0xe4/0x100
[<ffffffff81884c52>] ret_from_fork+0x22/0x40
This happens because we increment rx_pkts on -ENOMEM and -EIO, resulting
in rx_pkts > 0. Fix this by only bumping rx_pkts if we were actually
given a non-zero budget.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bytes_compl and pkts_compl pointers passed to efx_dequeue_buffers
cannot be NULL. Add a paranoid warning to check this condition and fix
the one case where they were NULL.
efx_enqueue_unwind() is called very rarely, during error handling.
Without this fix it would fail with a NULL pointer dereference in
efx_dequeue_buffer, with efx_enqueue_skb in the call stack.
Fixes: e9117e5099 ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
add appropriate calls to clk_disable_unprepare() by jumping to out_mdio
in case orion_mdio_probe() returns -EPROBE_DEFER.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3d604da1e9 ("net: mvmdio: get and enable optional clock")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some dual port NICs, the 2 ports have to be configured with compatible
link speeds. Under some conditions, a port's configured speed may no
longer be supported. The firmware will send a message to the driver
when this happens.
Improve this logic that prints out the warning by only printing it if
we can determine the link speed that is no longer supported. If the
speed is unknown or it is in autoneg mode, skip the warning message.
Reported-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, whenever the NETIF_F_HW_TC feature changes, we silently
always allow it, but we actually do not disable the flows in HW
on disable. That breaks user's expectations. So just forbid
the feature disable in case there are any filters offloaded.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcfm_dev always points to the correct netdev and we already
hold a refcnt, so no need to use tcfm_ifindex to lookup again.
If we would support moving target netdev across netns, using
pointer would be better than ifindex.
This also fixes dumping obsolete ifindex, now after the
target device is gone we just dump 0 as ifindex.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload IP header checksum to NIC.
This fixes a previous patch which disabled checksum offloading
for both IPv4 and IPv6 packets. So L3 checksum offload was
getting disabled for IPv4 pkts. And HW is dropping these pkts
for some reason.
Without this patch, IPv4 TSO appears to be broken:
WIthout this patch I get ~16kbyte/s, with patch close to 2mbyte/s
when copying files via scp from test box to my home workstation.
Looking at tcpdump on sender it looks like hardware drops IPv4 TSO skbs.
This patch restores performance for me, ipv6 looks good too.
Fixes: fa6d7cb5d7 ("net: thunderx: Fix TCP/UDP checksum offload for IPv6 pkts")
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Aleksey Makarov <aleksey.makarov@auriga.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch warns that:
drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c:160 bnxt_tc_parse_actions()
error: uninitialized symbol 'rc'.
"rc" is either uninitialized or set to zero here so we can just remove
the check.
Fixes: 8c95f773b4 ("bnxt_en: add support for Flower based vxlan encap/decap offload")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the rx_fs_lock is no longer held across allocation, it's safe
to use GFP_KERNEL for allocating new entries.
This reverts commit 81da3bf6e3 ("net: macb: change GFP_KERNEL to
GFP_ATOMIC").
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae8223de3d ("net: macb: Added support for RX filtering")
introduces a lock, rx_fs_lock which is intended to protect the list of
rx_flow items and synchronize access to the hardware rx filtering
registers.
However, the region protected by this lock is overscoped, unnecessarily
including things like slab allocation. Reduce this lock scope to only
include operations which must be performed atomically: list traversal,
addition, and removal, and hitting the macb filtering registers.
This fixes the use of kmalloc w/ GFP_KERNEL in atomic context.
Fixes: ae8223de3d ("net: macb: Added support for RX filtering")
Cc: Rafal Ozieblo <rafalo@cadence.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list_for_each_entry() macro already handles the case where the list
is empty (by not executing the loop body). It's not necessary to handle
this case specially, so stop doing so.
Cc: Rafal Ozieblo <rafalo@cadence.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the rmnet device creation fails in the newlink either while
registering with the physical device or after subsequent
operations, the rmnet endpoint information is never freed.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a skb in transmit path does not have sufficient headroom to add
the map header, the skb is not sent out and is never freed.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- The spec defines CSR address ranges for indirect ME CSRs. For Each TLV
chunk in the spec, dump a chunk that includes the spec and the data
over the defined address range.
- Each indirect CSR has 8 contexts. To read one context, first write the
context to a specific derived address, read it back, and then read the
register value.
- For each address, read and dump all 8 contexts in this manner.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- The spec defines CSR address ranges for these types.
- Dump each TLV chunk in the spec as a chunk that includes the spec and
the data over the defined address range.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump FW name as TLV, based on dump specification.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add spec TLV for hwinfo field, containing key string as data.
- Add dump TLV for hwinfo field, with data being key and value as packed
zero-terminated strings.
- If specified hwinfo field is not found, dump the spec TLV as -ENOENT
error.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Dump hwinfo as separate TLV chunk, in a packed format containing
zero-separated key and value strings.
- This provides additional debug context, if requested by the dumpspec.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Support rtsym TLVs.
- If specified rtsym is not found, dump the spec TLV as -ENOENT error.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Perform dumpspec traversals for calculating size and populating the
dump.
- Initially, wrap all spec TLVs in dump error TLVs (changed by later
patches in the series).
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use a TLV structure, with the typed chunks aligned to 8-byte sizes.
- Dump numeric fields as big-endian.
- Prolog contains the dump level.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load the TLV-based binary specification of what needs to be included in
a dump, from the "_abi_dump_spec" rtsymbol. If the symbol is not defined,
then dumps for levels >= 1 are not supported.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Skeleton code to perform a binary debug dump via ethtoolops
"set_dump", "get_dump_flags" and "get_dump_data", i.e. the ethtool
-W/w mechanism.
- Skeleton functions for debugdump operations provided.
- An integer "dump level" can be specified, this is stored between
ethtool invocations. Dump level 0 is still the "arm.diag" resource for
backward compatibility. Other dump levels each define a set of state
information to include in the dump, driven by a spec from FW.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NULL as argument for the DMA mapping API is bogus, as the DMA
mapping API may use information from the "struct device" to perform
the DMA mapping operation. Therefore, pass the appropriate "struct
device".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two types of "struct device": the one representing the
physical device on its physical bus (platform, SPI, PCI, etc.), and
the one representing the logical device in its device class (net,
etc.).
The DMA mapping API expects to receive as argument a "struct device"
representing the physical device, as the "struct device" contains
information about the bus that the DMA API needs.
However, the sh_eth driver mistakenly uses the "struct device"
representing the logical device (embedded in "struct net_device")
rather than the "struct device" representing the physical device on
its bus.
This commit fixes that by adjusting all calls to the DMA mapping API.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the phylib now being aware of the "reset-gpios" PHY node property,
there should be no need to frob the PHY reset in this driver anymore...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to LS1021A RM, the value of PAL can be set so that the start of the
IP header in the receive data buffer is aligned to a 32-bit boundary. Normally,
setting PAL = 2 provides minimal padding to ensure such alignment of the IP
header.
However every incoming packet's 8-byte time stamp will be inserted into the
packet data buffer as padding alignment bytes when hardware time stamping is
enabled.
So we set the padding 8+2 here to avoid the flooded alignment faults:
root@128:~# cat /proc/cpu/alignment
User: 0
System: 17539 (inet_gro_receive+0x114/0x2c0)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 17539
User faults: 2 (fixup)
Also shown when exception report enablement
CPU: 0 PID: 161 Comm: irq/66-eth1_g0_ Not tainted 4.1.21-rt13-WR8.0.0.0_preempt-rt #16
Hardware name: Freescale LS1021A
[<8001b420>] (unwind_backtrace) from [<8001476c>] (show_stack+0x20/0x24)
[<8001476c>] (show_stack) from [<807cfb48>] (dump_stack+0x94/0xac)
[<807cfb48>] (dump_stack) from [<80025d70>] (do_alignment+0x720/0x958)
[<80025d70>] (do_alignment) from [<80009224>] (do_DataAbort+0x40/0xbc)
[<80009224>] (do_DataAbort) from [<80015398>] (__dabt_svc+0x38/0x60)
Exception stack(0x86ad1cc0 to 0x86ad1d08)
1cc0: f9b3e080 86b3d072 2d78d287 00000000 866816c0 86b3d05e 86e785d0 00000000
1ce0: 00000011 0000000e 80840ab0 86ad1d3c 86ad1d08 86ad1d08 806d7fc0 806d806c
1d00: 40070013 ffffffff
[<80015398>] (__dabt_svc) from [<806d806c>] (inet_gro_receive+0x114/0x2c0)
[<806d806c>] (inet_gro_receive) from [<80660eec>] (dev_gro_receive+0x21c/0x3c0)
[<80660eec>] (dev_gro_receive) from [<8066133c>] (napi_gro_receive+0x44/0x17c)
[<8066133c>] (napi_gro_receive) from [<804f0538>] (gfar_clean_rx_ring+0x39c/0x7d4)
[<804f0538>] (gfar_clean_rx_ring) from [<804f0bf4>] (gfar_poll_rx_sq+0x58/0xe0)
[<804f0bf4>] (gfar_poll_rx_sq) from [<80660b10>] (net_rx_action+0x27c/0x43c)
[<80660b10>] (net_rx_action) from [<80033638>] (do_current_softirqs+0x1e0/0x3dc)
[<80033638>] (do_current_softirqs) from [<800338c4>] (__local_bh_enable+0x90/0xa8)
[<800338c4>] (__local_bh_enable) from [<8008025c>] (irq_forced_thread_fn+0x70/0x84)
[<8008025c>] (irq_forced_thread_fn) from [<800805e8>] (irq_thread+0x16c/0x244)
[<800805e8>] (irq_thread) from [<8004e490>] (kthread+0xe8/0x104)
[<8004e490>] (kthread) from [<8000fda8>] (ret_from_fork+0x14/0x2c)
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In exisiting code, the way to detect if driver/client reset should
be executed or if hardware should be be soft resetted was overly
complex.
Existing code use to read the interrupt status register from task
context to figure out if the interrupt source event was reset and
then use clear the interrupt source for reset while waiting for the
hardware to finish the reset. This behaviour again was confusing
and overly complex in terms of the flow.
This patch simplifies the handling of the requested reset and the
pending reset(i.e. reset which have already been asserted by the
software and hardware has acknowledged back to driver that it is
processing the hardware reset through interrupt)
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing common service task was being used to service the reset
requests. This patch tries to make the handling of reset cleaner
by separating task to handle the reset requests. This might in
turn help in adapting similar handling approach for other
interrupt events like mailbox, sharing vector 0 interrupt.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset interrupt event shares common miscellaneous interrupt
Vector 0. In the existing reset interrupt handling we disable
the Vector 0 interrupt in misc interrupt handler and re-enable
them later in context to common service task.
This also means other event sources like mailbox would also be
deferred or if the interrupt event was due to mailbox(which shall
be supported for VF soon), it could delay the reset handling.
This patch reorganizes the reset interrupt handling logic and
makes it more fair to other events.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we swapped the tx_packets, tx_bytes and tx_dropped counters
with rx_packets, rx_bytes and rx_dropped counters, respectively. This
behaviour is correct and expected for VF representors but it should not
be swapped for physical port mac representors.
Fixes: eadfa4c3be ("nfp: add stats and xmit helpers for representors")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function gem_add_flow_filter called on line 2958 inside lock on line 2949
but uses GFP_KERNEL
Generated by: scripts/coccinelle/locks/call_kern.cocci
Fixes: ae8223de3d ("net: macb: Added support for RX filtering")
CC: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small overlapping change conflict ('net' changed a line,
'net-next' added a line right afterwards) in flexcan.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2017-12-03
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Addition of a software model for BPF offloads in order to ease
testing code changes in that area and make semantics more clear.
This is implemented in a new driver called netdevsim, which can
later also be extended for other offloads. SR-IOV support is added
as well to netdevsim. BPF kernel selftests for offloading are
added so we can track basic functionality as well as exercising
all corner cases around BPF offloading, from Jakub.
2) Today drivers have to drop the reference on BPF progs they hold
due to XDP on device teardown themselves. Change this in order
to make XDP handling inside the drivers less error prone, and
move disabling XDP to the core instead, also from Jakub.
3) Misc set of BPF verifier improvements and cleanups as preparatory
work for upcoming BPF-to-BPF calls. Among others, this set also
improves liveness marking such that pruning can be slightly more
effective. Register and stack liveness information is now included
in the verifier log as well, from Alexei.
4) nfp JIT improvements in order to identify load/store sequences in
the BPF prog e.g. coming from memcpy lowering and optimizing them
through the NPU's command push pull (CPP) instruction, from Jiong.
5) Cleanups to test_cgrp2_attach2.c BPF sample code in oder to remove
bpf_prog_attach() magic values and replacing them with actual proper
attach flag instead, from David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool ops to advertise sw timestamping.
Call skb_tx_timestamp() just before ringing the wq doorbell.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one extraneous level of indentation on assignment statement.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mss variable tracks the last max segment size sent to the TSO
engine. We do not update the hardware as long as we receive skb:s with
the same value in gso_size.
During a network device down/up cycle (mapped to stmmac_release() and
stmmac_open() callbacks) we issue a reset to the hardware and it
forgets the setting for mss. However we did not zero out our mss
variable so the next transmission of a gso packet happens with an
undefined hardware setting.
This triggers a hang in the TSO engine and eventuelly the netdev
watchdog will bark.
Fixes: f748be531d ("stmmac: support new GMAC4")
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
short_input variable is assigned to another data pointer which is
referred out of its scope. Fix it by moving short_input definition
to the beginning of bnxt_hwrm_do_send_msg() function.
No failure has been reported so far due to this issue.
Fixes: e605db801b ("bnxt_en: Support for Short Firmware Message")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For flows that involve a vxlan encap action, the vxlan sock
interface may be specified as the outgoing interface. The driver
must resolve the outgoing PF interface used by this socket and
use the dst_fid of the PF in the hwrm_cfa_encap_record_alloc cmd.
Similarily for flows that have a vxlan decap action, the
fid of the incoming PF interface must be used as the src_fid in
the hwrm_cfa_decap_filter_alloc cmd.
Fixes: 8c95f773b4 ("bnxt_en: add support for Flower based vxlan encap/decap offload")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While creating a decap filter the tunnel smac need not (and must not) be
specified as we cannot ascertain the neighbor in the recv path. 'ttl'
match is also not needed for the decap filter and must be wild-carded.
Fixes: f484f6782e ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sunil Challa <sunilkumar.challa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current 'bnxt_shutdown' implementation only invokes
'bnxt_ulp_shutdown' to shut down RoCE in the case when the system is in
the path of power off (SYSTEM_POWER_OFF). While this may work in most
cases, it does not work in the smart NIC case, when Linux 'reboot'
command is initiated from the Linux that runs on the ARM cores of the
NIC card. In this particular case, Linux 'reboot' results in a system
'L3' level reset where the entire ARM and associated subsystems are
being reset, but at the same time, Nitro core is being kept in sane state
(to allow external PCIe connected servers to continue to work). Without
properly shutting down RoCE and freeing all associated resources, it
results in the ARM core to hang immediately after the 'reboot'
By always invoking 'bnxt_ulp_shutdown' in 'bnxt_shutdown', it fixes the
above issue
Fixes: 0efd2fc65c ("bnxt_en: Add a callback to inform RDMA driver during PCI shutdown.")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since day one of XDP drivers had to remember to free the program
on the remove path. This leads to code duplication and is error
prone. Make the stack query the installed programs on unregister
and if something is installed, remove the program. Freeing of
program attached to XDP generic is moved from free_netdev() as well.
Because the remove will now be called before notifiers are
invoked, BPF offload state of the program will not get destroyed
before uninstall.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Some drivers enforce that flags on program replacement and
removal must match the flags passed on install. This leaves
the possibility open to enable simultaneous loading
of XDP programs both to HW and DRV.
Allow such drivers to report the flags back to the stack.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
ALE ports number includes the Host port and ext Ports, and
ALE ports numbering starts from 0, so correct corresponding port
checks in cpsw_ale_control_set/get().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpsw_ale_create in cpsw_ale_create(). This also makes
cpsw_ale_destroy() function nop, so remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move static initialization from cpsw_ale_start() to cpsw_ale_create() as it
does not make much sence to perform static initializtion in
cpsw_ale_start() which is called everytime netif[s] is opened.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ale->params.ale_ports parameter can be used to deriver values for all
ale entry mask bits: port_mask_bits, port_mask_bits, port_num_bits.
Hence, calculate above values and drop all hardcoded values. For
port_num_bits calcualtion use order_base_2() API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALE is enabled from cpsw_ale_start() now, but disabled only from
cpsw_ale_destroy() which introduces inconsitance as cpsw_ale_start() is
called when netif[s] is opened, but cpsw_ale_destroy() is called when
driver is removed. Hence, move ALE disabling in cpsw_ale_stop().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI OMAP/Sitara SoCs have fixed number of ALE ports 3, which includes Host
port also.
Hence, use fixed value instead of value calcualted from DT, which can be
set by user and might not reflect actual HW configuration.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mac_hi/lo defines in common header cpsw.h and re-use
them for netcp_ethss.c.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW platform data struct cpsw_platform_data and struct cpsw_slave_data are
used only incide cpsw.c module, so move these definitions there.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unused variable "poll" from cpsw_update_channels_res().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ETH_RESET_AP support handling to reset the internal
Application Processor(s) of the SmartNIC card.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the optimization frontend, but adding a new eBPF IR scan
pass "nfp_bpf_opt_ldst_gather".
The pass will traverse the IR to recognize the load/store pairs sequences
that come from lowering of memory copy builtins.
The gathered memory copy information will be kept in the meta info
structure of the first load instruction in the sequence and will be
consumed by the optimization backend added in the previous patches.
NOTE: a sequence with cross memory access doesn't qualify this
optimization, i.e. if one load in the sequence will load from place that
has been written by previous store. This is because when we turn the
sequence into single CPP operation, we are reading all contents at once
into NFP transfer registers, then write them out as a whole. This is not
identical with what the original load/store sequence is doing.
Detecting cross memory access for two random pointers will be difficult,
fortunately under XDP/eBPF's restrictied runtime environment, the copy
normally happen among map, packet data and stack, they do not overlap with
each other.
And for cases supported by NFP, cross memory access will only happen on
PTR_TO_PACKET. Fortunately for this, there is ID information that we could
do accurate memory alias check.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When the gathered copy length is bigger than 32-bytes and within 128-bytes
(the maximum length a single CPP Pull/Push request can finish), the
strategy of read/write are changeed into:
* Read.
- use direct reference mode when length is within 32-bytes.
- use indirect mode when length is bigger than 32-bytes.
* Write.
- length <= 8-bytes
use write8 (direct_ref).
- length <= 32-byte and 4-bytes aligned
use write32 (direct_ref).
- length <= 32-bytes but not 4-bytes aligned
use write8 (indirect_ref).
- length > 32-bytes and 4-bytes aligned
use write32 (indirect_ref).
- length > 32-bytes and not 4-bytes aligned and <= 40-bytes
use write32 (direct_ref) to finish the first 32-bytes.
use write8 (direct_ref) to finish all remaining hanging part.
- length > 32-bytes and not 4-bytes aligned
use write32 (indirect_ref) to finish those 4-byte aligned parts.
use write8 (direct_ref) to finish all remaining hanging part.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
For NFP, we want to re-group a sequence of load/store pairs lowered from
memcpy/memmove into single memory bulk operation which then could be
accelerated using NFP CPP bus.
This patch extends the existing load/store auxiliary information by adding
two new fields:
struct bpf_insn *paired_st;
s16 ldst_gather_len;
Both fields are supposed to be carried by the the load instruction at the
head of the sequence. "paired_st" is the corresponding store instruction at
the head and "ldst_gather_len" is the gathered length.
If "ldst_gather_len" is negative, then the sequence is doing memory
load/store in descending order, otherwise it is in ascending order. We need
this information to detect overlapped memory access.
This patch then optimize memory bulk copy when the copy length is within
32-bytes.
The strategy of read/write used is:
* Read.
Use read32 (direct_ref), always.
* Write.
- length <= 8-bytes
write8 (direct_ref).
- length <= 32-bytes and is 4-byte aligned
write32 (direct_ref).
- length <= 32-bytes but is not 4-byte aligned
write8 (indirect_ref).
NOTE: the optimization should not change program semantics. The destination
register of the last load instruction should contain the same value before
and after this optimization.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It is usual that we need to check if one BPF insn is for loading/storeing
data from/to memory.
Therefore, it makes sense to factor out related code to become common
helper functions.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add support for emitting commands with field overwrites.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When immed is used with No-Dest, the emitter should use reg.dst instead of
reg.areg for the destination, using the latter will actually encode
register zero.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The NFP normally requires the source operands to be difference addressing
modes, but we should rule out the very special NN_REG_NONE type.
There are instruction that ignores both A/B operands, for example:
local_csr_rd
For these instructions, we might pass the same operand type, NN_REG_NONE,
for both A/B operands.
NOTE: in current NFP ISA, it is only possible for instructions with
unrestricted operands to take none operands, but in case there is new and
similar instructoin in restricted form, they would follow similar rules,
so swreg_to_restricted is updated as well.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If any of the shift insns in the ld/shift sequence is jump destination,
don't do combination.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If the mask insn in the ld/mask pair is jump destination, then don't do
combination.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP eBPF offload JIT engine is doing some instruction combine based
optimizations which however must not be safe if the combined sequences
are across basic block boarders.
Currently, there are post checks during fixing jump destinations. If the
jump destination is found to be eBPF insn that has been combined into
another one, then JIT engine will raise error and abort.
This is not optimal. The JIT engine ought to disable the optimization on
such cross-bb-border sequences instead of abort.
As there is no control flow information in eBPF infrastructure that we
can't do basic block based optimizations, this patch extends the existing
jump destination record pass to also flag the jump destination, then in
instruction combine passes we could skip the optimizations if insns in the
sequence are jump targets.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
eBPF insns are internally organized as dual-list inside NFP offload JIT.
Random access to an insn needs to be done by either forward or backward
traversal along the list.
One place we need to do such traversal is at nfp_fixup_branches where one
traversal is needed for each jump insn to find the destination. Such
traversals could be avoided if jump destinations are collected through a
single travesal in a pre-scan pass, and such information could also be
useful in other places where jump destination info are needed.
This patch adds such jump destination collection in nfp_prog_prepare.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch adds support for backward jump on NFP.
- restrictions on backward jump in various functions have been removed.
- nfp_fixup_branches now supports backward jump.
There is one thing to note, currently an input eBPF JMP insn may generate
several NFP insns, for example,
NFP imm move insn A \
NFP compare insn B --> 3 NFP insn jited from eBPF JMP insn M
NFP branch insn C /
---
NFP insn X --> 1 NFP insn jited from eBPF insn N
---
...
therefore, we are doing sanity check to make sure the last jited insn from
an eBPF JMP is a NFP branch instruction.
Once backward jump is allowed, it is possible an eBPF JMP insn is at the
end of the program. This is however causing trouble for the sanity check.
Because the sanity check requires the end index of the NFP insns jited from
one eBPF insn while only the start index is recorded before this patch that
we can only get the end index by:
start_index_of_the_next_eBPF_insn - 1
or for the above example:
start_index_of_eBPF_insn_N (which is the index of NFP insn X) - 1
nfp_fixup_branches was using nfp_for_each_insn_walk2 to expose *next* insn
to each iteration during the traversal so the last index could be
calculated from which. Now, it needs some extra code to handle the last
insn. Meanwhile, the use of walk2 is actually unnecessary, we could simply
use generic single instruction walk to do this, the next insn could be
easily calculated using list_next_entry.
So, this patch migrates the jump fixup traversal method to
*list_for_each_entry*, this simplifies the code logic a little bit.
The other thing to note is a new state variable "last_bpf_off" is
introduced to track the index of the last jited NFP insn. This is necessary
because NFP is generating special purposes epilogue sequences, so the index
of the last jited NFP insn is *not* always nfp_prog->prog_len - 1.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Since commit 3a025e1d1c ("Add optional check for bad kernel-doc
comments") when built with W=1 build will complain about kdoc errors.
Fix the kdoc issues we have. kdoc is still confused by defines in
nfp_net_ctrl.h but those are not really errors.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch allows filtering received packets to different
hardware queues (aka ntuple).
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able for packet reception on different RX queues some
configuration has to be performed. This patch checks how many
hardware queue does GEM support and initializes them.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver expect "allwinner,leds-active-low" to be in PHY node, but
the binding doc expect it to be in MAC node.
Since all board DT use it also in MAC node, the driver need to search
allwinner,leds-active-low in MAC node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In xmit, it is very impossible that TX_ERROR occurs. So using
unlikely optimizes the xmit process.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netxen_collect_minidump() evidently just wants to get a monotonic
timestamp. Using jiffies_to_timespec(jiffies, &ts) is not
appropriate here, since it will overflow after 2^32 jiffies,
which may be as short as 49 days of uptime.
ktime_get_seconds() is the correct interface here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to reinvent the wheel, we have bus_find_device_by_name().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
on T81 there are only 4 cores, hence setting max queue count to 4
would leave nothing for XDP_TX. This patch fixes this by doubling
max queue count in above scenarios.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: cjacob <cjacob@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for XDP_REDIRECT. Flush is not
yet supported.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: cjacob <cjacob@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserved and unused fields in the Tx descriptors should be 0. The PPv2
driver doesn't clear them at run-time (for performance reasons) but
these descriptors aren't zeroed when allocated, which can lead to
unpredictable behaviors. This patch fixes this by using
dma_zalloc_coherent instead of dma_alloc_coherent.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
Don't use %x and casting to print out an address, instead use %p
and remove the casting. Cleans up smatch warnings:
drivers/net/ethernet/via/via-rhine.c:998 rhine_init_one_common()
warn: argument 4 to %lx specifier is cast from pointer
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64-bit (e.g. powerpc64/allmodconfig):
drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit_done':
drivers/net/ethernet/xilinx/ll_temac_main.c:633:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
^
cdmac_bd.app4 is u32, so it is too small to hold a kernel pointer.
Note that several other fields in struct cdmac_bd are also too small to
hold physical addresses on 64-bit platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error code returned by 'bnxt_read_sfp_module_eeprom_info()' is handled a
few lines above when reading the A0 portion of the EEPROM.
The same should be done when reading the A2 portion of the EEPROM.
In order to correctly propagate an error, update 'rc' in this 2nd call as
well, otherwise 0 (success) is returned.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the Tx ring size checks when using ethtool, by adding
an extra check in the PPv2 check_ringparam_valid helper. The Tx ring
size cannot be set to a value smaller than the minimum number of
descriptors needed for TSO.
Fixes: 1d17db08c0 ("net: mvpp2: limit TSO segments and use stop/wake thresholds")
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Short fragmented packets may never be sent by the hardware when padding
is disabled. This patch stop modifying the GMAC padding bits, to leave
them to their reset value (disabled).
Fixes: 3919357fb0 ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes the probe error path by cleaning up probed ports, to
avoid leaving registered net devices when the driver failed to probe.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an allocation in the txq_init path fails, the allocated buffers
end-up being freed twice: in the txq_init error path, and in txq_deinit.
This lead to issues as txq_deinit would work on already freed memory
regions:
kernel BUG at mm/slub.c:3915!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
This patch fixes this by removing the txq_init own error path, as the
txq_deinit function is always called on errors. This was introduced by
TSO as way more buffers are allocated.
Fixes: 186cd4d4e4 ("net: mvpp2: software tso support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_nexthop_rif_update() walks the list of nexthops
associated with a RIF, and updates the corresponding entries in the
switch. It is used in particular when a tunnel underlay netdevice moves
to a different VRF, and all the nexthops are migrated over to a new RIF.
The problem is that each nexthop holds a reference to its RIF, and that
is not updated. So after the old RIF is gone, further activity on these
nexthops (such as downing the underlay netdevice) dereferences a
dangling pointer.
Fix the issue by updating rif of impacted nexthops before calling
mlxsw_sp_nexthop_rif_update().
Fixes: 0c5f1cd5ba ("mlxsw: spectrum_router: Generalize __mlxsw_sp_ipip_entry_update_tunnel()")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tunnels that are offloadable on their own can nonetheless be
demoted to slow path if their local address is in conflict with that of
another tunnel. When a route is formed for such a tunnel,
mlxsw_sp_nexthop_ipip_init() fails to find the corresponding IPIP entry,
and that triggers a FIB abort.
Resolve the problem by not assuming that a tunnel for which
mlxsw_sp_ipip_ops.can_offload() holds also automatically has an IPIP
entry.
Fixes: af641713e9 ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw driver currently doesn't offload GRE tunnels if they have the
same local address and use the same underlay VRF. When such a situation
arises, the tunnels in conflict are demoted to slow path.
However, the current code only verifies this condition on tunnel
creation and tunnel change, not when a tunnel is moved to a different
VRF. When the tunnel has no bound device, underlay and overlay are the
same. Thus moving a tunnel moves the underlay as well, and that can
cause local address conflict.
So modify mlxsw_sp_netdevice_ipip_ol_vrf_event() to check if there are
any conflicting tunnels, and demote them if yes.
Fixes: af641713e9 ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new local route is added, an IPIP entry is looked up to determine
whether the route should be offloaded as a tunnel decap or as a trap.
That decision should take into account whether the tunnel netdevice in
question is actually IFF_UP, and only install a decap offload if it is.
Fixes: 0063587d35 ("mlxsw: spectrum: Support decap-only IP-in-IP tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding cloud filters could fail for a number of reasons,
unsupported filter fields for example, which fails during
validation of fields itself. This will not result in admin
command errors and converting the admin queue status to posix
error code using i40e_aq_rc_to_posix would result in incorrect
error values. If the failure was due to AQ error itself,
reporting that correctly is handled in the inner function.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
