There's a few places where we need to access a GPC register from ucode,
but outside of the falcon's io address space. To do this we need to
calculate the offset based on which GPC we're executing on.
This used to be done manually, but we've since found a "base" offset
that can be added by the hardware. To use this, an extra bit needs to
be set in the register address, which is what this macro achieves.
There should be no functional change from this commit.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes detection of a failed attempt at fetching the entire ROM image
in one-shot (a violation of the spec, that works a lot of the time).
Tested on a HP Zbook 15 G2.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
No locking is required for the traversal of this list, as it only
happens during suspend/resume where nothing else can be executing.
Fixes some of the issues noticed during parallel piglit runs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
USIF already takes the client mutex, but will need access to ABI16 data
in order to provide some limited interoperability.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This patch uses an approach closer to the nvidia driver to configure
both PLLs for high gddr5 memory clocks (usually above 2400MHz)
Previously nouveau used the one PLL as it was used for the lower clocks
and just adjusted the second PLL to get as close as possible to the
requested clock. This means for my card, that I got a 4050 MHz clock
although 4008 MHz was requested.
Now the driver iterates over a list of PLL configuration also used by
the nvidia driver and then adjust the second PLL to get near the
requested clock. Also it hold to some restriction I found while
analyzing the PLL configurations
This won't fix all gddr5 high clock issues itself, but it should be
fine on hybrid gpu systems as found on many laptops these days. Also
switching while normal desktop usage should be a lot more stable than
before.
v2: move the pll code into ramgk104
Signed-off-by: Karol Herbst <nouveau@karolherbst.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Your milage may vary, as it's only been tested on a single G94 and one G96.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Avoids waiting for VBLANKS that never arrive on headless or otherwise
unconventional set-ups. Strategy taken from MEMX.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
10053c is not even read on some cards, and I have no idea exactly what the
criteria are. Likely NVIDIA pre-scans the VBIOS and in their driver disables
all features that are never used. The practical effect should be the same
as this implementation though.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Like Pierre's G94. We might want to structure Kepler similarly in a follow-up.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Does not seem to be necessary for NVA0, hence untested by me.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Seems to be mostly equal to DDR3 on < GT218, should improve stability for
DDR2 reclocks.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
In preparation of changing FBVDDQ, as observed on at least one GDDR3 card.
While at it, adhere to func.log[1] properly for consistency.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
If the hardware supports extended tag field (8-bit ones), then enable it.
This is usually done by the VBIOS, but not on some MBPs (see fdo#86537).
In case extended tag field is not supported, 5-bit tag field is used which
limits the possible number of requests to 32. Apparently bits 7:0 of
0x08841c stores some number of outstanding requests, so cap it to 32 if
extended tag is unsupported.
Fixes: fdo#86537
v2: Restrict changes to chipsets >= 0x84
v3:
* Add nvkm_pci_mask to pci.h
* Mask bit 8 before setting it
v4:
* Rename `add` argument of nvkm_pci_mask to `value`
* Move code from nvkm_pci_init to g84_pci_init and remove PCIe and chipset
checks
v5:
* Rebase code on latest PCI structure
* Restore PCIe check
* Fix namings in nvkm_pci_mask
* Rephrase part of the commit message
Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
These nvkm_object_func structures are never modified. All other
nvkm_object_func structures are declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GF110+ supports both the A and B compute classes, make sure to accept
both.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
NVIDIA provided the documentation for mp error 0x10, INVALID_ADDR_SPACE,
which apparently happens when trying to use an atomic operation on
local or shared memory (instead of global memory).
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
If pm_runtime_get_sync() we were going to "out" but we missed freeing
vma.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
coverity.com reported that memset was using a buffer of size 0, on
checking the code it turned out that the function was not being used. So
remove it.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Was not able to obtain a trace of NVRM due to kernel version annoyances,
however, experimentally confirmed that the WAR we use on NV50/G8x boards
works here too.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Increase clock timeout of some unknown engines in order to avoid failure
at high gpcclk rate.
This fixes IBUS read faults on my GF119 when reclocking is manually
enabled. Note that memory reclocking is completely broken and NvMemExec
has to be disabled to allow core clock reclocking only.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
I got confirmation that we can read and change the voltage with the same code.
The divider is also computed correctly on the gm204 we got our hands on.
Thanks to Yoshimo on IRC for executing the tests on his gm204!
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Let's ignore the other desktop Maxwells until I get my hands on one and confirm
that we still can change the voltage.
Signed-off-by: Martin Peres <martin.peres@free.fr>
Most Keplers actually use the GPIO-based voltage management instead of the new
PWM-based one. Use the GPIO mode as a fallback as it already gracefully handles
the case where no GPIOs exist.
All the Maxwells seem to use the PWM method though.
v2:
- Do not forget to commit the PWM configuration change!
Signed-off-by: Martin Peres <martin.peres@free.fr>
This patch is not ideal but it definitely beats a rewrite of the current
interface and is very self-contained.
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
So far the DMA mask was not set for platform devices, which limited them
to a 32-bit physical space. Allow dma_set_mask() to be called for
non-PCI devices, and also take the IOMMU bit into account since it could
restrict the physically addressable space.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The pci_dma_* functions are now superseeded in the kernel by the DMA
API. Make the conversion to this more generic API.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Use the IOMMU bit specified in platform data instead of hardcoding it to
the bit used by current Tegra GPUs.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Current Tegra code taking advantage of the IOMMU assumes a hardcoded
value for the IOMMU bit. Make it a platform property instead for
flexibility.
v2 (Ben Skeggs): remove nvkm dependence on drm structures
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The Great Nouveau Refactoring Take II brought us a lot of goodness,
including acquire/release methods that are called before and after an
instobj is modified. These functions can be used as synchronization
points to manage CPU/GPU coherency if we modify an instobj using the
CPU.
This patch replaces the legacy and slow PRAMIN access for gk20a instmem
with CPU mappings and writes. A LRU list is used to unmap unused
mappings after a certain threshold (currently 1MB) of mapped instobjs is
reached. This allows mappings to be reused most of the time.
Accessing instobjs using the CPU requires to maintain the GPU L2 cache,
which we do in the acquire/release functions. This triggers a lot of L2
flushes/invalidates, but most of them are performed on an empty cache
(and thus return immediately), and overall context setup performance
greatly benefits from this (from 250ms to 160ms on Jetson TK1 for a
simple libdrm program).
Making L2 management more explicit should allow us to grab some more
performance in the future.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
No longer required in a lot of cases, as objects are identified over NVIF
via an alternate mechanism since the rework.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Allow clients to manually flush and invalidate L2. This will be useful
for Tegra systems for which we want to write instmem using the CPU.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
These are useful for systems without a coherent CPU/GPU bus. For such
systems we may need to maintain the L2 ourselves.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reintroduce macros allowing us to test a register against a certain
mask, since this is the most common usage pattern for the more generic
nvkm_xsec macros and makes the code more concise and readable.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some devices may not have a PMU. Avoid a NULL pointer dereference in
such cases by checking whether the pointer given to nvkm_pmu_pgob() is
valid.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On nv50+, we restrict the valid domains to just the one where the buffer
was originally created. However after the buffer is evicted to system
memory, we might move it back to a different domain that was not
originally valid. When sharing the buffer and retrieving its GEM_INFO
data, we still want the domain that will be valid for this buffer in a
pushbuf, not the one where it currently happens to be.
This resolves fdo#92504 and several others. These are due to suspend
evicting all buffers, making it more likely that they temporarily end up
in the wrong place.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92504
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
