Previously we always had something hooked up to LVDS so we tried very
hard to get a mode. With the Minnowboard this is no longer the case.
If no mode can be found over DDC or the firmware we just ignore LVDS.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
For the minnowboard to work the values found in EMGD are required.
This might break Oaktrail but without hardware to test with I cannot
really tell (and do not really care).
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This turned out to be tricky. Writing to SDVOB on the primary vdc also
writes to SDVOB on the aux vdc, but reading it back on the primary vdc
always fails. Basically we never read from the primary vdc since we
will end up trashing the aux vdc.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Since we can have SDVO on Pipe B we better check the output type instead
of pipe number for Oaktrail HDMI.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
On SDVO pipes (always Pipe B on mrst) we have to sequentially write the
aux vdc. We might be able to skip programming the primary vdc in
some/most places but we don't care about that now.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
We start off by adding SDVO limits and converting all limits to the
generic gma_limit_t stuct. Then we separate clock calculations for
LVDS and SDVO. This will be cleaned up later but keep it simple for now.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
Let's be a bit more consistent with our error values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- CRC support from Damien and He Shuang. Long term this should allow us to
test an awful lot modesetting corner cases automatically. So for me as
the maintainer this is really big.
- HDMI audio fix from Jani.
- VLV dpll computation code refactoring from Ville.
- Fixups for the gpu booster from last time around (Chris).
- Some cleanups in the context code from Ben.
- More watermark work from Ville (we'll be getting there ...).
- vblank timestamp improvements from Ville.
- CONFIG_FB=n support, including drm core changes to make the fbdev
helpers optional.
- DP link training improvements (Jani).
- mmio vtable from Ben, prep work for future hw.
* tag 'drm-intel-next-2013-10-18' of git://people.freedesktop.org/~danvet/drm-intel: (132 commits)
drm/i915/dp: don't mention eDP bpp clamping if it doesn't affect bpp
drm/i915: remove dead code in ironlake_crtc_mode_set
drm/i915: crc support for hsw
drm/i915: fix CRC debugfs setup
drm/i915: wait one vblank when disabling CRCs
drm/i915: use ->get_vblank_counter for the crc frame counter
drm/i915: wire up CRC interrupt for ilk/snb
drm/i915: add CRC #defines for ilk/snb
drm/i915: extract display_pipe_crc_update
drm/i915: don't Oops in debugfs for I915_FBDEV=n
drm/i915: set HDMI pixel clock in audio configuration
drm/i915: pass mode to ELD write vfuncs
cpufreq: Add dummy cpufreq_cpu_get/put for CONFIG_CPU_FREQ=n
drm/i915: check gem bo size when creating framebuffers
drm/i915: Use unsigned long for obj->user_pin_count
drm/i915: prevent tiling changes on framebuffer backing storage
drm/i915: grab dev->struct_mutex around framebuffer_init
drm/i915: vlv: fix VGA hotplug after modeset
drm: add support for additional stereo 3D modes
drm/i915: preserve dispaly init order on ByT
...
So drm was abusing device lifetimes, by having embedded device structures
in the minor and connector it meant that the lifetime of the internal drm
objects (drm_minor and drm_connector) were tied to the lifetime of the device
files in sysfs, so if something kept those files opened the current code
would kfree the objects and things would go downhill from there.
Now in reality there is no need for these lifetimes to be so intertwined,
especailly with hotplugging of devices where we wish to remove the sysfs
and userspace facing pieces before we can unwind the internal objects due
to open userspace files or mmaps, so split the objects out so the struct
device is no longer embedded and do what fbdev does and just allocate
and remove the sysfs inodes separately.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Following files contains code that is common to all intel mid
soc's. So renamed them as below.
mrst/mrst.c -> intel-mid/intel-mid.c
mrst/vrtc.c -> intel-mid/intel_mid_vrtc.c
mrst/early_printk_mrst.c -> intel-mid/intel_mid_vrtc.c
pci/mrst.c -> pci/intel_mid_pci.c
Also, renamed the corresponding header files and made changes
to the driver files that included these header files.
To ensure that there are no functional changes, I have compared
the objdump of renamed files before and after rename and found
that the only difference is file name change.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: http://lkml.kernel.org/r/1382049336-21316-4-git-send-email-david.a.cohen@linux.intel.com
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
For drivers which might want to disable fbdev legacy support.
Select the new option in all drivers for now, so this shouldn't result
in any change. Drivers need some work anyway to make fbdev support
optional (if they have it implemented, that is), so the recommended
way to expose this is by adding per-driver options. At least as long
as most drivers don't support disabling the fbdev support.
v2: Update for new drm drivers msm and rcar-du. Note that Rob's msm
driver can already take advantage of this, which allows us to build
msm without any fbdev depencies in the kernel!
v3: Move the MODULE_* stuff from the fbdev helper file to
drm_crtc_helper.c.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 8b9ba7a3 'drm/gma500: use gem get/put page helpers' was missing a
line, which resulted in garbled screen.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Guillaume CLÉMENT <gclement@baobob.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We can get the PCI vendor and device IDs via dev->pdev. So we can drop
the duplicated information.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_vblank_init() is too ugly. Make it a bit easier on the eye by
collecting all the per-crtc vblank counters, timestamps etc. to
a structure and just allocate an array of those.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vblank_disable_allowed is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers embed gem-objects into their own buffer objects. There is no
reason to keep drm_gem_object_alloc(), gem->driver_private and
->gem_init_object() anymore.
New drivers are highly encouraged to do the same. There is no benefit in
allocating gem-objects separately.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Here's some gma500 unifying and cleanups for drm-next. There is more stuff in
the pipe for 3.12 but I'd like to get these out of the way first.
* 'gma500-next' of git://github.com/patjak/drm-gma500: (35 commits)
drm/gma500/cdv: Add and hook up chip op for disabling sr
drm/gma500/cdv: Add and hook up chip op for watermarks
drm/gma500: Rename psb_intel_encoder to gma_encoder
drm/gma500: Rename psb_intel_connector to gma_connector
drm/gma500: Rename psb_intel_crtc to gma_crtc
drm/gma500/cdv: Convert to generic set_config()
drm/gma500/psb: Convert to generic set_config()
drm/gma500: Add generic set_config() function
drm/gma500/cdv: Convert to generic save/restore
drm/gma500/psb: Convert to generic save/restore
drm/gma500: Add generic crtc save/restore funcs
drm/gma500: Convert to generic encoder funcs
drm/gma500: Add generic encoder functions
drm/gma500/psb: Convert to generic cursor funcs
drm/gma500/cdv: Convert to generic cursor funcs
drm/gma500: Add generic cursor functions
drm/gma500/psb: Convert to generic crtc->destroy
drm/gma500/mdfld: Use identical generic crtc funcs
drm/gma500/oak: Use identical generic crtc funcs
drm/gma500/psb: Convert to gma_crtc_dpms()
...
Some Poulsbo cards seem to incorrectly report SDVO_CMD_STATUS_TARGET_NOT_SPECIFIED instead of SDVO_CMD_STATUS_PENDING, which causes the display to be turned off.
Signed-off-by: Guillaume Clement <gclement@baobob.org>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The gma500 driver somehow set the DRIVER_IRQ_VBL flag, but since
there's no code at all to check for this we can kill it. The other two
are completely unused.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
So I've stumbled over drm_fasync and wondered what it does. Digging
that up is quite a story.
First I've had to read up on what this does and ended up being rather
bewildered why peopled loved signals so much back in the days that
they've created SIGIO just for that ...
Then I wondered how this ever works, and what that strange "No-op."
comment right above it should mean. After all calling the core fasync
helper is pretty obviously not a noop. After reading through the
kernels FASYNC implementation I've noticed that signals are only sent
out to the processes attached with FASYNC by calling kill_fasync.
No merged drm driver has ever done that.
After more digging I've found out that the only driver that ever used
this is the so called GAMMA driver. I've frankly never heard of such a
gpu brand ever before. Now FASYNC seems to not have been the only bad
thing with that driver, since Dave Airlie removed it from the drm
driver with prejudice:
commit 1430163b4bbf7b00367ea1066c1c5fe85dbeefed
Author: Dave Airlie <airlied@linux.ie>
Date: Sun Aug 29 12:04:35 2004 +0000
Drop GAMMA DRM from a great height ...
Long story short, the drm fasync support seems to be doing absolutely
nothing. And the only user of it was never merged into the upstream
kernel. And we don't need any fops->fasync callback since the fcntl
implementation in the kernel already implements the noop case
correctly.
So stop this particular cargo-cult and rip it all out.
v2: Kill drm_fasync assignments in rcar (newly added) and imx drivers
(somehow I've missed that one in staging). Also drop the reference in
the drm DocBook. ARM compile-fail reported by Rob Clark.
v3: Move the removal of dev->buf_asnyc assignment in drm_setup to this
patch here.
v4: Actually git add ... tsk.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a callback hook to the chip ops struct to allow chips to have their
specific self-refresh function. Currently only used by cdv.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Add a callback hook to the chip ops struct to allow chips to have their
specific fifo watermark update function. Currently only cdv actually
tries to set wms based on crtc configuration but if/when the other chips
needs it we can attach a callback for them as well.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Because, there is no reason for it not to be const.
v1: original
v2: fix compile break in vmwgfx, and couple related cleanups suggested
by Ville Syrjälä
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All the gem based kms drivers really want the same function to
destroy a dumb framebuffer backing storage object.
So give it to them and roll it out in all drivers.
This still leaves the option open for kms drivers which don't use GEM
for backing storage, but it does decently simplify matters for gem
drivers.
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Cc: Ben Skeggs <skeggsb@gmail.com>
Reviwed-by: Rob Clark <robdclark@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the new vma manager instead of the old hashtable. Also convert all
drivers to use the new convenience helpers. This drops all the
(map_list.hash.key << PAGE_SHIFT) non-sense.
Locking and access-management is exactly the same as before with an
additional lock inside of the vma-manager, which strictly wouldn't be
needed for gem.
v2:
- rebase on drm-next
- init nodes via drm_vma_node_reset() in drm_gem.c
v3:
- fix tegra
v4:
- remove duplicate if (drm_vma_node_has_offset()) checks
- inline now trivial drm_vma_node_offset_addr() calls
v5:
- skip node-reset on gem-init due to kzalloc()
- do not allow mapping gem-objects with offsets (backwards compat)
- remove unneccessary casts
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Use the generic gma functions instead of the medfield functions where
they are identical.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Use the generic gma functions instead of the oaktrail functions where
they are identical.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This takes care of the remaining chips using the old generic code.
We don't check if the pipe number is valid but the old code peeked in
the register map before checking anyways so just ignore it.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
There is a slight difference in how we pick the palette register in the
generic function but we should be ok as long as psb_intel_crtc->pipe and
the register map is sane.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This patch makes psb use the gma_xxx counterparts that are identical. I
took them in one sweep as they should not cause any regressions.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This patch makes cdv use the gma_xxx counterparts that are identical. I
took them in one sweep as they should not cause any regressions.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Add chip specific callbacks for the generic and non-generic clock
calculation code. Also remove as much dupilicated code as possible.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Replace any use of xxx_intel_pipe_has_type() with the generic
gma_pipe_has_type() function. Poulsbo still use it but that will be
removed when we rip out psb_intel_pipe_has_type().
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Add chip specific callbacks for the generic and non-generic clock
calculation code. Also remove as much dupilicated code as possible.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This patch aims to unify the bits and pieces that are common (or similar
enough) for pll clock calculations. Nothing makes use of this code yet
That will come in later patches.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
drm_gem_object_init() and drm_gem_private_object_init() do exactly the
same (except for shmem alloc) so make the first use the latter to reduce
code duplication.
Also drop the return code from drm_gem_private_object_init(). It seems
unlikely that we will extend it any time soon so no reason to keep it
around. This simplifies code paths in drivers, too.
Last but not least, fix gma500 to call drm_gem_object_release() before
freeing objects that were allocated via drm_gem_private_object_init().
That isn't actually necessary for now, but might be in the future.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Patrik writes:
Two fixes for memory leaks split into Cedarview and Poulsbo versions,
and a fix for properly setting the pipe base when using fbdev. It's on
my todo-list to start unifying the chips since they are very similar,
but until then I'd like to split them up in case there are side-effects
on Cedarview that I cannot currently test.
airled: Verified pull from github matches what I expected.
* 'gma500-fixes' of git://github.com/patjak/drm-gma500:
drm/gma500/cdv: Fix cursor gem obj referencing on cdv
drm/gma500/psb: Fix cursor gem obj referencing on psb
drm/gma500/cdv: Unpin framebuffer on crtc disable
drm/gma500/psb: Unpin framebuffer on crtc disable
drm/gma500: Add fb gtt offset to fb base
The internal crtc cursor gem object pointer was never set/updated since
it was required to be set in the first place.
Fixing this will make the pin/unpin count match and prevent cursor
objects from leaking when userspace drops all references to it. Also
make sure we drop the gem obj reference on failure.
This patch only affects Cedarview chips.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
The internal crtc cursor gem object pointer was never set/updated since
it was required to be set in the first place.
Fixing this will make the pin/unpin count match and prevent cursor
objects from leaking when userspace drops all references to it. Also
make sure we drop the gem obj reference on failure.
This patch only affects Poulsbo chips.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Cedarview.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=889511
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=812113
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
The framebuffer needs to be unpinned in the crtc->disable callback
because of previous pinning in psb_intel_pipe_set_base(). This will fix
a memory leak where the framebuffer was released but not unpinned
properly. This patch only affects Poulsbo.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=889511
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=812113
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Old code assumed framebuffer starts at base of stolen memory. Since the
addition of hardware cursors, this might not be true anymore so add the
gtt offset to the calculation.
Reported-by: Holger Schurig <holgerschurig@gmail.com>
Tested-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 3.10.
Wierd bits:
- OMAP drm changes required OMAP dss changes, in drivers/video, so I
took them in here.
- one more fbcon fix for font handover
- VT switch avoidance in pm code
- scatterlist helpers for gpu drivers - have acks from akpm
Highlights:
- qxl kms driver - driver for the spice qxl virtual GPU
Nouveau:
- fermi/kepler VRAM compression
- GK110/nvf0 modesetting support.
Tegra:
- host1x core merged with 2D engine support
i915:
- vt switchless resume
- more valleyview support
- vblank fixes
- modesetting pipe config rework
radeon:
- UVD engine support
- SI chip tiling support
- GPU registers initialisation from golden values.
exynos:
- device tree changes
- fimc block support
Otherwise:
- bunches of fixes all over the place."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (513 commits)
qxl: update to new idr interfaces.
drm/nouveau: fix build with nv50->nvc0
drm/radeon: fix handling of v6 power tables
drm/radeon: clarify family checks in pm table parsing
drm/radeon: consolidate UVD clock programming
drm/radeon: fix UPLL_REF_DIV_MASK definition
radeon: add bo tracking debugfs
drm/radeon: add new richland pci ids
drm/radeon: add some new SI PCI ids
drm/radeon: fix scratch reg handling for UVD fence
drm/radeon: allocate SA bo in the requested domain
drm/radeon: fix possible segfault when parsing pm tables
drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
OMAPDSS: VENC: Add error handling for venc_probe_pdata
OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
OMAPDSS: DSI: Add error handling for dsi_probe_pdata
OMAPDSS: SDI: Add error handling for sdi_probe_pdata
OMAPDSS: DPI: Add error handling for dpi_probe_pdata
...
Two fixes for gma500. First one from Anisse allows us to handle ASLE irqs even
when BIOS doesn't trigger a pipe event irq. The second one allows dual head
setups to have a big shared framebuffer.
* 'gma500-fixes' of git://github.com/patjak/drm-gma500:
drm/gma500: Increase max resolution for mode setting
drm/gma500: fix backlight hotkeys behaviour on netbooks
By having a higher max resolution we can now set up a virtual
framebuffer that spans several monitors. 4096 should be ok since we're
gen 3 or higher and should be enough for most dual head setups.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Backlight hotkeys weren't working before on certain cedartrail laptops.
The source of this problem is that the hotkeys' ASLE opregion interrupts
were simply ignored. Driver seemed to expect the interrupt to be
associated with a pipe, but it wasn't.
Accepting the ASLE interrupt without an associated pipe event flag fixes
the issue, the backlight code is called when needed, making the
brightness keys work properly.
[patrik: This patch affects irq handling on any netbook with opregion support]
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=833597
Reference: http://lists.freedesktop.org/archives/dri-devel/2012-July/025279.html
Cc: stable@kernel.org
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Patrik writes:
I haven't had much review or testing on other platforms than Poulsbo but
at least the following Cedarview bug has been squashed and no
regressions reported: https://bugs.freedesktop.org/show_bug.cgi?id=58527
* 'gma500-next' of git://github.com/patjak/drm-gma500:
drm/gma500: Add debugging info to psb_gtt_restore()
drm/gma500: Check connector status before restoring sdvo
gma500:fix build failure for 3.9-rc5
drm/gma500: Fix hibernation problems on sdvo encoders
drm/gma500: Add hooks for hibernation
drm/gma500: Activate the gtt rebuild on suspend/resume
drm/gma500: Add support for rebuilding the gtt
drm/gma500: Change fb name so pm-utils doesn't apply quirks
gma500: Make VGA and HDMI connector hotpluggable
drm/gma500: Clean up various defines
drm/gma500: Remove unnecessary function exposure
drm/gma500: Type clock limits directly into array and remove defines
drm/gma500: Calculate clock in one function instead of three identical
drm/gma500: Remove unused i8xx clock limits
gma500: medfield: Fix possible NULL pointer dereference
drivers: gpu: drm: gma500: Replaced calls kzalloc & memcpy with kmemdup
gma500: remove unused drm_psb_no_fb
This patch fixes a bug introduced by:
commit 749387dc8d
Author: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Date: Sun Apr 7 16:35:50 2013 +0200
drm/gma500: Fix hibernation problems on sdvo encoders
The bug is triggered when we do a mode set on a sdvo encoder with all
connectors in the disconnected state. A crtc is considered enabled by
drm even though all of its connectors are disconnected. Work around
this by adding a check in our sdvo restore function.
Also remove the unneeded dpms on. Prepare and Commit will take care of
that.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Last version of this patch is not clear enough and X86 duplicated.
This patch fixes build failure of v3.9-rc5 and rc6.
When config ACPI_VIDEO as m, DRM_GMA500 as y, here comes the failure.
GMA5/600 needs acpi_video just like nouveau.
And some tab type fix by the way.
Failure message:
drivers/built-in.o: In function `psb_driver_load':
kernel-3.9-rc5/drivers/gpu/drm/gma500/psb_drv.c:340: \
undefined reference to `acpi_video_register'
make: *** [vmlinux] Error 1
Signed-off-by: Xiong Zhou <jencce.kernel@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
The state of the SDVO chip is more difficult to save than the LVDS so we do a
full mode set on the crtc to get SDVO operational again. The SDVOB/C register is
also stored just in case we have special bits set in the future.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Currently we do whatever is done during suspend/resume but we might need some
more work for hibernation so keep them in separate functions.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This patch activates the rebuilding of the gtt. Currently we reinitialize the
gtt by inserting the stolen pages again and map the rest to our scratch page.
Then we go about restoring the needed ranges. This is a bit overkill but right
now we don't have that much to restore so better safe than sorry.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
By having 'drm' and 'fb' in the fb screeninfo id, pm-utils will leave us
alone. Otherwise we'll have quirks up to our ears and resume will break.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Both VGA and HDMI connectors are available on my Asus EeePC X101CH.
This patch will cause output to be shown on either when plugged in.
For both, it shows the leftmost 800x600, of the 1024x600 on LVDS.
Signed-off-by: Kero van Gelder <kero@chello.nl>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
psb_intel_crtc_gamma_set() and psb_intel_crtc_destroy() aren't used outside of
psb_intel_display.c right now so no need to expose them.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This makes it easier to read. We do the same for cdv so it becomes more
consistent as well.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
i9xx_clock() and i8xx_clock() did the same calc and psb_intel_clock() just
called i9xx_clock() so just move it all into psb_intel_clock().
The same calculation is duplicated in cdv_intel_display.c as well so maybe we
can share it later on.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
The use of pointer sender should be after the NULL check.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Replaced calls kzalloc followed by memcpy with call to kmemdup.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
commit f9f23a77f07506a32d9dc1d925bf85c0e7507b66(gma500: remove no_fb bits)
remove all the drm_psb_no_fb relations code in gma500 except this line code,
so remove it also.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
The values of n, m1 and m2 needs to be subtracted by 2 before writing them to
the FP register. The dot clock calculation already thinks of these values in
register form so we must also specify them as such.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
The fb helper lost its support for reallocating an fb completely, so
no need to return special success values any more.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should be done in the drivers for two reasons:
- it gets in the way of fastboot efforts
- it links the fb helpers with the crtc helpers instead of going
through the real interface vfuncs, forcing i915 to fake all the
->disable callbacks used by the crtc helper to avoid ugly Oopsen
v2: Resolve conflicts since drivers still call
drm_fb_helper_single_add_all_connectors.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no reason kgdb.h itself needs to include the 8250 serial port
header file. So push it down to the _very_ limited number of individual
drivers that need the values in that file, and fix up the places where
people really wanted serial_core.h and platform_device.h.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Dave Airlie <airlied@redhat.com>
CC: Alan Cox <alan@linux.intel.com>
CC: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have two classes of framebuffer
- Created by the driver (atm only for fbdev), and the driver holds
onto the last reference count until destruction.
- Created by userspace and associated with a given fd. These
framebuffers will be reaped when their assoiciated fb is closed.
Now these two cases are set up differently, the framebuffers are on
different lists and hence destruction needs to clean up different
things. Also, for userspace framebuffers we remove them from any
current usage, whereas for internal framebuffers it is assumed that
the driver has done this already.
Long story short, we need two different ways to cleanup such drivers.
Three functions are involved in total:
- drm_framebuffer_remove: Convenience function which removes the fb
from all active usage and then drops the passed-in reference.
- drm_framebuffer_unregister_private: Will remove driver-private
framebuffers from relevant lists and drop the corresponding
references. Should be called for driver-private framebuffers before
dropping the last reference (or like for a lot of the drivers where
the fbdev is embedded someplace else, before doing the cleanup
manually).
- drm_framebuffer_cleanup: Final cleanup for both classes of fbs,
should be called by the driver's ->destroy callback once the last
reference is gone.
This patch just rolls out the new interfaces and updates all drivers
(by adding calls to drm_framebuffer_unregister_private at all the
right places)- no functional changes yet. Follow-on patches will move
drm core code around and update the lifetime management for
framebuffers, so that we are no longer required to keep framebuffers
alive by locking mode_config.mutex.
I've also updated the kerneldoc already.
vmwgfx seems to again be a bit special, at least I haven't figured out
how the fbdev support in that driver works. It smells like it's
external though.
v2: The i915 driver creates another private framebuffer in the
load-detect code. Adjust its cleanup code, too.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only two places:
- suspend/resume
- Some really strange mode validation tool with too much funny-lucking
hand-rolled conversion code.
- The recently-added lastclose fbdev restore code.
Better safe than sorry, so convert both places to keep the locking
semantics as much as possible.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Doing this within the fb->destroy callback leads to a locking
nightmare. And all other drm drivers that restore the fbcon do
it in lastclose, too.
With this adjustments all fb->destroy callbacks optionally drop
references to any gem objects used as backing storage, call
drm_framebuffer_cleanup and then kfree the struct. Which nicely
simplifies the locking for framebuffer unreferencing and freeing,
since this doesn't require that we hold the mode_config lock. A
slight exception is the vmwgfx surface backed framebuffer, it also
calls drm_master_put and removes the object from a device-private
framebuffer list. Both seem to have solid locking in place already.
Conclusion is that now it is no longer required to hold the
mode_config lock while freeing a framebuffer.
v2: Drop the corresponding mutex_lock WARN check from
drm_framebuffer_unreference.
v3: Use just the mode_config lock not modeset_lock_all, due to patch
reordering.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With more fine-grained locking we can no longer rely on the big
mode_config lock to prevent concurrent access to mode resources
like framebuffers. Instead a framebuffer becomes accessible to
other threads as soon as it is added to the relevant lookup
structures. Hence it needs to be fully set up by the time drivers
call drm_framebuffer_init.
This patch here is the drivers part of that reorg. Nothing really fancy
going on safe for three special cases.
- exynos needs to be careful to properly unref all handles.
- nouveau gets a resource leak fixed for free: one of the error
cases didn't cleanup the framebuffer, which is now moot since
the framebuffer is only registered once it is fully set up.
- vmwgfx requires a slight reordering of operations, I'm hoping I didn't
break anything (but it's refcount management only, so should be safe).
v2: Split out exynos, since it's a bit more hairy than expected.
v3: Drop bogus cirrus hunk noticed by Richard Wilbur.
v4: Split out vmwgfx since there's a small change in return values.
Reviewed-by: Rob Clark <rob@ti.com> (core + omapdrm)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, and __devexit
from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the NULL test for dev since it never be NULL.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are still some mysteries left, in particular how (and in
fact if) the EDID is supposed to work on the HDMI port. However
the basic stuff now works and I can plug my Q550 into an HDMI
display and get the expected results.
[v2: cleans up space/tab and other formatting as per Dave's
request]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Remove redundant DRM UAPI header #inclusions from drivers/gpu/.
Remove redundant #inclusions of core DRM UAPI headers (drm.h, drm_mode.h and
drm_sarea.h). They are now #included via drmP.h and drm_crtc.h via a preceding
patch.
Without this patch and the patch to make include the UAPI headers from the core
headers, after the UAPI split, the DRM C sources cannot find these UAPI headers
because the DRM code relies on specific -I flags to make #include "..." work
on headers in include/drm/ - but that does not work after the UAPI split without
adding more -I flags.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into drm-intel-next-queued
Manual backmerge of -rc7 to resolve a silent conflict leading to
compile failure in drivers/gpu/drm/i915/intel_hdmi.c.
This is due to the bugfix in -rc7:
commit b98b601672
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 07:43:22 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
Since this code moved around a lot in -next git put that snippet at
the wrong spot. I've tried to fix this by making the conflict explicit
by merging a version for next with:
commit 3cce574f01
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 11:19:00 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug unconditionally
But that failed to solve the entire problem. To avoid pushing out
further -nightly branch to our QA where this is broken, do the
backmerge and manually add the stuff git adds to -next from the patch
in -fixes.
Note that this doesn't show up in git's merge diff (and hence is also
not handled by git rerere), which adds to the reasons why I'd like to
fix this with a verbose backmerge. The git merge diff only shows a
bunch of trivial conflicts of the "code changed in lines next to each
another" kind.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch removes a unused struct psb_intel_connector
Sparse gives a warning:
drivers/gpu/drm/gma500/cdv_intel_hdmi.c:142:30: warning:
unused variable ‘psb_intel_connector’ [-Wunused-variable]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The register map patches didn't set one value for the GMA600 which
means the Fujitsu Q550 dies on boot with the GMA500 driver enabled.
Add the map entry so we don't read from the device MMIO + 0 by mistake.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Horses <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]
This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver. It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board. Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we have a 266MHz part we set core_freq to 0 in several spots
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Another reference to raw_edid field of struct drm_display_info was added in
gma500 while the whole field was being removed, causing build
failure. Remove the hopefully last references to raw_edid.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
This is set when setting DPMS on and off, but it isn't checked anywhere,
so just remove it.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Neither the drm core nor any of the drivers really need the raw_edid field
of struct drm_display_info for anything. Instead of being useful, it
creates confusion about who is responsible for freeing the memory it points
to and setting the field to NULL afterwards, leading to memory leaks and
dangling pointers.
Remove the raw_edid field, and fix drivers as necessary.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We should be making this call not praying that the values are right.
In addition as noted by Josiah Standing we should be calling this
for eDP as well.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The private gem_create_mmap_offset() function is now implemented in the
DRM core as drm_gem_create_mmap_offset(). Use it and kill the private
copy.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I don't know why the DP/eDP is affected by the clock gating. But the test
shows that it really fixes the DP/eDP clock issue during enabling DP/eDP.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[Updated to only apply the workaround if the device has DP. We don't want
to do this on netbooks]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduce the eDP support into the driver.
This has been reworked a bit because kernel driver proper uses encoder/connectors
while the legacy Intel driver uses the old output stuff.
It also diverges on the backlight handling. The legacy Intel driver adds a panel
abstraction based upon the i915 one. It's only really used for backlight bits
and we have a perfectly good backlight abstraction which can extend instead.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[ported to upstream driver, redid backlight abstraction]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on bits from Yakui <yakui.zhao@intel.com>
We can import various little bits of code before we plumb it all
in and hopefully this way catch any regressions more easily.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Import the pieces we need in order to do DisplayPort. Don't wire them
up yet as there is work to do to integrate them.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on the spec, the CRT output doesn't use the lane. And the HDMI B output
uses the Lane0/1 while the HDMI C output uses the Lane 2/3. But currently
it will program all the four lanes for the CRT/HDMI.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[Ported to the in-kernel driver]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently when trying to call the DPMS off again for one CRTC with DPMS off,
it will firstly disable the SR and can't enable it again because of the
incorrect check/logic. In such case the self refresh is still disabled
although one CRTC pipe is active. This is wrong.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[Ported to in kernel driver]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm updates from Dave Airlie:
"One of the smaller drm -next pulls in ages!
Ben (nouveau) has a rewrite in progress but we decided to leave it
stew for another cycle, so just some fixes from him.
- radeon: lots of documentation work, fixes, more ring and locking
changes, pcie gen2, more dp fixes.
- i915: haswell features, gpu reset fixes, /dev/agpgart removal on
machines that we never used it on, more VGA/HDP fix., more DP fixes
- drm core: cleanups from Daniel, sis 64-bit fixes, range allocator
colouring.
but yeah fairly quiet merge this time, probably because I missed half
of it!"
Trivial add-add conflict in include/linux/pci_regs.h
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (255 commits)
drm/nouveau: init vblank requests list
drm/nv50: extend vblank semaphore to generic dmaobj + offset pair
drm/nouveau: mark most of our ioctls as deprecated, move to compat layer
drm/nouveau: move current gpuobj code out of nouveau_object.c
drm/nouveau/gem: fix object reference leak in a failure path
drm/nv50: rename INVALID_QUERY_OR_TEXTURE error to INVALID_OPERATION
drm/nv84: decode PCRYPT errors
drm/nouveau: dcb table quirk for fdo#50830
nouveau: Fix alignment requirements on src and dst addresses
drm/i915: unbreak lastclose for failed driver init
drm/i915: Set the context before setting up regs for the context.
drm/i915: constify mode in crtc_mode_fixup
drm/i915/lvds: ditch ->prepare special case
drm/i915: dereferencing an error pointer
drm/i915: fix invalid reference handling of the default ctx obj
drm/i915: Add -EIO to the list of known errors for __wait_seqno
drm/i915: Flush the context object from the CPU caches upon switching
drm/radeon: fix dpms on/off on trinity/aruba v2
drm/radeon: on hotplug force link training to happen (v2)
drm/radeon: fix hotplug of DP to DVI|HDMI passive adapters (v2)
...
All leftover users either haven't set DRIVER_HAVE_DMA, in which
case this will never be called, or use the drm_core implementation.
Call that directly in the only callsite.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The passed mode must not be modified by the operation, make it const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some desktop environments carefully save and restore the brightness
settings from the previous boot. Unfortunately they don't all check to
see if the range has changed. The end result is that they restore a
brightness of 100/lots not 100/100.
As the old driver and the non-free GMA36xx driver both use 0-100 we thus
need to go back doing the same thing to avoid users getting a mysterious
black screen after boot.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise we end up getting the masks wrong, can get events before we
are doing power control and other ungood things. Again this is a
regression fix where the ordering of handling was disturbed by other
work, and the user experience on some boxes is a blank screen.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now set up the lid timer before we set up the backlight. On some
devices that causes a crash as we do a backlight change before or during
the setup.
As this fixes a crash on boot regression on some setups it ought to go
in ASAP, especially as all the user gets is a blank screen.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are unintuitive. These are type bool and return -1 casted to true
on failure. Let's just make it return an int. The callers don't care,
but let's change this as a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DRM mode config functions structure declared by drivers and pointed
to by the drm_mode_config funcs field is never modified. Make it a const
pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Rob Clark <rob.clark@linaro.org>
Reviwed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The GEM vm operations structure is passed to the VM core that stores it
in a const field. There vm operations structures can thus be const in
DRM as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rob Clark <rob.clark@linaro.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Poulsbo needs a physical address in the cursor base register. We allocate a
stolen memory buffer and copy the cursor image provided by userspace into it.
When/If we get our own userspace driver we can map this stolen memory directly.
The patch also adds a mark in chip ops so we can identify devices that has this
requirement.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
