[Why]
Sink OUI supported cap is not set so driver skips programming it.
[How]
Revert the change the skips OUI programming if the cap is not set
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
use correct logger context
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Test expects that we also read HPD_IRQ_VECTOR when checking for
symbol loss as well lane status.
[How]
Read bytes 0x200-0x205 instead of just 0x202-0x205
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Feature requires synchronization of dig, pipe, and cursor locking
between driver and fw.
[How]
Set flag to force psr to use hw lock mgr.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk
according to bandwidth requirement. call stack: rv1_update_clocks -->
update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth
--> prepare_bandwidth / optimize_bandwidth. before change dcn hw,
prepare_bandwidth will be called first to allow enough clock,
watermark for change, after end of dcn hw change, optimize_bandwidth
is executed to lower clock to save power for new dcn hw settings.
below is sequence of commit_planes_for_stream:
step 1: prepare_bandwidth - raise clock to have enough bandwidth
step 2: lock_doublebuffer_enable
step 3: pipe_control_lock(true) - make dchubp register change will
not take effect right way
step 4: apply_ctx_for_surface - program dchubp
step 5: pipe_control_lock(false) - dchubp register change take effect
step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream
for full_date, optimize clock to save power
at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be
changed for new dchubp configuration. but real dcn hub dchubps are
still running with old configuration until end of step 5. this need
clocks settings at step 1 should not less than that before step 1.
this is checked by two conditions: 1. if (should_set_clock(safe_to_lower
, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) ||
new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz)
2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz
the second condition is based on new dchubp configuration. dppclk
for new dchubp may be different from dppclk before step 1.
for example, before step 1, dchubps are as below:
pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979)
pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080)
for dppclk for pipe0 need dppclk = dispclk
new dchubp pipe split configuration:
pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080)
pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080)
dppclk only needs dppclk = dispclk /2.
dispclk, dppclk are not lock by otg master lock. they take effect
after step 1. during this transition, dispclk are the same, but
dppclk is changed to half of previous clock for old dchubp
configuration between step 1 and step 6. This may cause p-state
warning intermittently.
[How]
for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we
need make sure dppclk are not changed to less between step 1 and 6.
for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz,
new display clock is raised, but we do not know ratio of
new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz,
new_clocks->dispclk_khz /2 does not guarantee equal or higher than
old dppclk. we could ignore power saving different between
dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6.
as long as safe_to_lower = false, set dpclk = dispclk to simplify
condition check.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Each asic can optimize best based on its capabilities
[How]
Optimizing timing for a new pixel clock
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Programming DCN is explicitly forbidden during idle optimzations allowed
state. Existing implemenation relies on OS/DM, which is not robust. Instead
DC should sequence this.
Note that DC will not re-enter idle optimized state on its own, it is only
responsible for catching out of sequence calls. It is still DM
responsibility to sequence appropriate for optimized power, but this change
removes the requirement for DM to cover the .1% case.
[How]
- elevate updates during idle optimized state to full updates
- disable idle power optimizations prior to programming
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Setting abm level does not correctly update CRTC state. As a result
no surface update is added to dc stream state and triggers warning.
[How]
Correctly update CRTC state when setting abm level property.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use DCN21 functions instead of DCE110
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently navy_flounder is using sienna_cichlid_dmcub.bin.
[How]
Create a seperate define so navy_flounder will use its own firmware.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some monitors could suffer symbol unlock but cannot send HPD IRQ to
notic source device to handle link loss. This makes monitor stuck in
abnormal status and causes black screen.
[How]
According to the suggestion from scalar vendor, to check lane status
again after link training done. That can improve the comaptibility
from current production monitors.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dcn3_update_clocks there are situations where dppclk is not
lowered (i.e. stays the same), but DTO still needs to be increased
before we program pipe frontend (i.e. in prepare_bandwidth). If we
don't program the new DTO value before we program the pipe,
we will underflow as soon as the pipe lock is released until the
next call to dcn3_update_clocks where the DTO is updated.
[How]
Remove dppclk check before programming new DTO value.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Fix naming and return bits rather than bytes per pixel for
naming consistency. Because registers return Bytes per pixel,
but DSC Config structure is expecting bits per pixel as input.
So when returning the value convert from bytes into bits.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Struct dcn_dsc_state is used for reading current state
and parameters of DSC on a pipe, the target rate parameter
uses bytes per pixel even though its reading BITS_PER_PIXEL
register.
[How]
Changing it to Bits Per Pixel for consistency.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change replaces older looping code in favor of these functions.
[How]
There are built in functions for extracting global sync params
during mode validation now.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This was added in the past to solve the issue of not knowing when
to stall for medium and full updates in DM.
Since DC is ultimately decides what requires bandwidth changes we
wanted to make use of it directly to determine this.
The problem is that we can't actually pass any of the stream or surface
updates into DC global validation, so we don't actually check if the new
configuration is valid - we just validate the old existing config
instead and stall for outstanding commits to finish.
There's also the problem of grabbing the DRM private object for
pageflips which can lead to page faults in the case where commits
execute out of order and free a DRM private object state that was
still required for commit tail.
[How]
Now that we reset the plane in DM with the same conditions DC checks
we can have planes go through DC validation and we know when we need
to check and stall based on whether the stream or planes changed.
We mark lock_and_validation_needed whenever we've done this, so just
go back to using that instead of dm_determine_update_type_for_commit.
Since we'll skip resetting the plane for a pageflip we will no longer
grab the DRM private object for pageflips as well, avoiding the
page fault issued caused by pageflipping under load with commits
executing out of order.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MEDIUM or FULL updates can require global validation or affect
bandwidth. By treating these all simply as surface updates we aren't
actually passing this through DC global validation.
[How]
There's currently no way to pass surface updates through DC global
validation, nor do I think it's a good idea to change the interface
to accept these.
DC global validation itself is currently stateless, and we can move
our update type checking to be stateless as well by duplicating DC
surface checks in DM based on DRM properties.
We wanted to rely on DC automatically determining this since DC knows
best, but DM is ultimately what fills in everything into DC plane
state so it does need to know as well.
There are basically only three paths that we exercise in DM today:
1) Cursor (async update)
2) Pageflip (fast update)
3) Full pipe programming (medium/full updates)
Which means that anything that's more than a pageflip really needs to
go down path #3.
So this change duplicates all the surface update checks based on DRM
state instead inside of should_reset_plane().
Next step is dropping dm_determine_update_type_for_commit and we no
longer require the old DC state at all for global validation.
Optimization can come later so we don't reset DC planes at all for
MEDIUM udpates and avoid validation, but we might require some extra
checks in DM to achieve this.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
So we're not racing with userspace or deadlocking DM.
[How]
These flags are now stored on dm_plane_state itself and acquried and
validated during commit_check, so just use those instead.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're racing with userspace as the flags could potentially change
from when we acquired and validated them in commit_check.
[How]
We unfortunately can't drop this function in its entirety from
prepare_planes since we don't know the afb->address at commit_check
time yet.
So instead of querying new tiling_flags and tmz_surface use the ones
from the plane_state directly.
While we're at it, also update the force_disable_dcc option based
on the state from atomic check.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enabling or disable DCC or switching between tiled and linear formats
can require bandwidth updates.
They're currently skipping all DC validation by being treated as purely
surface updates.
[How]
Treat tiling_flag changes (which encode DCC state) as a condition for
resetting the plane.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Store these in advance so we can reuse them later in commit_tail without
having to reserve the fbo again.
These will also be used for checking for tiling changes when deciding
to reset the plane or not.
[How]
This change should mostly be a refactor. Only commit check is affected
for now and I'll drop the get_fb_info calls in prepare_planes and
commit_tail after.
This runs a prepass loop once we think that all planes have been added
to the context and replaces the get_fb_info calls with accessing the
dm_plane_state instead.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On an error exit path, a negative error code should be returned
instead of a positive return value.
Fixes: 9e869063b0 ("drm/amd/display: Move iteration out of dm_update_planes")
Cc: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The only usage of dcn30_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The only usage of dcn21_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The only usage of dcn20_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The if statement wasn't indented so it's confusing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
| [Header Changes]
| - Reworked the FW versioning to include hotfix
| and test bits
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There's currently no method to enable multi-stream synchronization from
userspace and we don't check the VSDB bits to know whether or not
specific displays should have the feature enable.
[how]
Add a debugfs entry that controls a new DM debug option,
"force_timing_sync". This debug option will set on any newly created
stream following the change to the debug option.
Expose a new interface from DC that performs the timing sync and a helper
to the "force_timing_sync" debugfs that iterates over the current streams
and modifies the current synchornization state and grouping.
Example usage to force a resync (from an X based desktop):
echo 1 > /sys/kernel/debug/dri/0/amdgpu_dm_force_timing_sync
xset dpms force off && xset dpms force on
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Display goes blank after driver installation.
Aux tuning parameters must be used for 2.x only.
Wrong dc_golden_table offset was used.
[How]
Implement a new enc3_hw_init function without VBIOS constants usage to
be called for 3.x
Calculate dc_golden_table offset using sum of
base dce_info offset and golden table offset
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During SetPathMode and UpdatePlanes, the plane state can be null. We default
to linear swizzle mode when plane state is null. This resulted in bandwidth
validation failing when trying to set 8K60 mode (which previously passed validation
during rebuild timing list).
[How]
Change the default swizzle mode from linear to 4kb_s and update pitch accordingly.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
Use dc_is_hdmi_signal to determine signal type.
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Sink OUI supported cap is not set so driver skips programming it.
[How]
Revert the change the skips OUI programming if the cap is not set
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some of the DSC debugfs read enteries are missing comments
explaining how to use and how to comprehend the results.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
use correct logger context
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to be able to specify bits per pixel for DSC on any
connector.
[How]
Overwrite computed DSC target rate in dsc_cfg, with requested value.
Overwrites for both SST and MST connectors, but in different places, but the process is identical. Overwrites only if DSC is decided to be enabled on that connector.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to be able to specify slice height for any connector's DSC
[How]
Overwrite computed parameters in dsc_cfg, with the value needed/
Overwrites for both SST and MST connectors, but in different places, but the process is identical. Overwrites only if DSC is decided to be enabled on that connector.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Trying to grab dma_resv_lock while in commit_tail before we've done
all the code that leads to the eventual signalling of the vblank event
(which can be a dma_fence) is deadlock-y. Don't do that.
Here the solution is easy because just grabbing locks to read
something races anyway. We don't need to bother, READ_ONCE is
equivalent. And avoids the locking issue.
v2: Also take into account tmz_surface boolean, plus just delete the
old code.
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: linux-rdma@vger.kernel.org
Cc: amd-gfx@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fixes a race condition that causes a use-after-free during
amdgpu_dm_atomic_commit_tail. This can occur when 2 non-blocking commits
are requested and the second one finishes before the first. Essentially,
this bug occurs when the following sequence of events happens:
1. Non-blocking commit #1 is requested w/ a new dm_state #1 and is
deferred to the workqueue.
2. Non-blocking commit #2 is requested w/ a new dm_state #2 and is
deferred to the workqueue.
3. Commit #2 starts before commit #1, dm_state #1 is used in the
commit_tail and commit #2 completes, freeing dm_state #1.
4. Commit #1 starts after commit #2 completes, uses the freed dm_state
1 and dereferences a freelist pointer while setting the context.
Since this bug has only been spotted with fast commits, this patch fixes
the bug by clearing the dm_state instead of using the old dc_state for
fast updates. In addition, since dm_state is only used for its dc_state
and amdgpu_dm_atomic_commit_tail will retain the dc_state if none is found,
removing the dm_state should not have any consequences in fast updates.
This use-after-free bug has existed for a while now, but only caused a
noticeable issue starting from 5.7-rc1 due to 3202fa62f ("slub: relocate
freelist pointer to middle of object") moving the freelist pointer from
dm_state->base (which was unused) to dm_state->context (which is
dereferenced).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207383
Fixes: bd200d190f ("drm/amd/display: Don't replace the dc_state for fast updates")
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: Mazin Rezk <mnrzk@protonmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Test expects that we also read HPD_IRQ_VECTOR when checking for
symbol loss as well lane status.
[How]
Read bytes 0x200-0x205 instead of just 0x202-0x205
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to be able to specify slice width for DSC on aconnector
[How]
Getting slice width parameter from debugfs entry, if it is
a valid the value is set in connector's dsc preffered settings
structure. Which then overwrites dsc_cfg structure's parameters
if DSC is decided to be enabled. Works for both SST and MST.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Feature requires synchronization of dig, pipe, and cursor locking
between driver and fw.
[How]
Set flag to force psr to use hw lock mgr.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk
according to bandwidth requirement. call stack: rv1_update_clocks -->
update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth
--> prepare_bandwidth / optimize_bandwidth. before change dcn hw,
prepare_bandwidth will be called first to allow enough clock,
watermark for change, after end of dcn hw change, optimize_bandwidth
is executed to lower clock to save power for new dcn hw settings.
below is sequence of commit_planes_for_stream:
step 1: prepare_bandwidth - raise clock to have enough bandwidth
step 2: lock_doublebuffer_enable
step 3: pipe_control_lock(true) - make dchubp register change will
not take effect right way
step 4: apply_ctx_for_surface - program dchubp
step 5: pipe_control_lock(false) - dchubp register change take effect
step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream
for full_date, optimize clock to save power
at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be
changed for new dchubp configuration. but real dcn hub dchubps are
still running with old configuration until end of step 5. this need
clocks settings at step 1 should not less than that before step 1.
this is checked by two conditions: 1. if (should_set_clock(safe_to_lower
, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) ||
new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz)
2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz
the second condition is based on new dchubp configuration. dppclk
for new dchubp may be different from dppclk before step 1.
for example, before step 1, dchubps are as below:
pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979)
pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080)
for dppclk for pipe0 need dppclk = dispclk
new dchubp pipe split configuration:
pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080)
pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080)
dppclk only needs dppclk = dispclk /2.
dispclk, dppclk are not lock by otg master lock. they take effect
after step 1. during this transition, dispclk are the same, but
dppclk is changed to half of previous clock for old dchubp
configuration between step 1 and step 6. This may cause p-state
warning intermittently.
[How]
for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we
need make sure dppclk are not changed to less between step 1 and 6.
for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz,
new display clock is raised, but we do not know ratio of
new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz,
new_clocks->dispclk_khz /2 does not guarantee equal or higher than
old dppclk. we could ignore power saving different between
dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6.
as long as safe_to_lower = false, set dpclk = dispclk to simplify
condition check.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need a mechanism to force enable DSC on any connector
[How]
Debugfs entry overwrites newly added connector's dsc preffered
settings structure and sets dsc_clock_en flag on it.
During the attomic commit, depending if connector is SST or
MST, we will enable DSC manually by overwriting stream's DSC flag.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Each asic can optimize best based on its capabilities
[How]
Optimizing timing for a new pixel clock
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Programming DCN is explicitly forbidden during idle optimzations allowed
state. Existing implemenation relies on OS/DM, which is not robust. Instead
DC should sequence this.
Note that DC will not re-enter idle optimized state on its own, it is only
responsible for catching out of sequence calls. It is still DM
responsibility to sequence appropriate for optimized power, but this change
removes the requirement for DM to cover the .1% case.
[How]
- elevate updates during idle optimized state to full updates
- disable idle power optimizations prior to programming
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Setting abm level does not correctly update CRTC state. As a result
no surface update is added to dc stream state and triggers warning.
[How]
Correctly update CRTC state when setting abm level property.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fixes a race condition that causes a use-after-free during
amdgpu_dm_atomic_commit_tail. This can occur when 2 non-blocking commits
are requested and the second one finishes before the first. Essentially,
this bug occurs when the following sequence of events happens:
1. Non-blocking commit #1 is requested w/ a new dm_state #1 and is
deferred to the workqueue.
2. Non-blocking commit #2 is requested w/ a new dm_state #2 and is
deferred to the workqueue.
3. Commit #2 starts before commit #1, dm_state #1 is used in the
commit_tail and commit #2 completes, freeing dm_state #1.
4. Commit #1 starts after commit #2 completes, uses the freed dm_state
1 and dereferences a freelist pointer while setting the context.
Since this bug has only been spotted with fast commits, this patch fixes
the bug by clearing the dm_state instead of using the old dc_state for
fast updates. In addition, since dm_state is only used for its dc_state
and amdgpu_dm_atomic_commit_tail will retain the dc_state if none is found,
removing the dm_state should not have any consequences in fast updates.
This use-after-free bug has existed for a while now, but only caused a
noticeable issue starting from 5.7-rc1 due to 3202fa62f ("slub: relocate
freelist pointer to middle of object") moving the freelist pointer from
dm_state->base (which was unused) to dm_state->context (which is
dereferenced).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207383
Fixes: bd200d190f ("drm/amd/display: Don't replace the dc_state for fast updates")
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: Mazin Rezk <mnrzk@protonmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
All DCE6 specific code changes are guarded by CONFIG_DRM_AMD_DC_SI Kconfig option
[How]
(v1) CONFIG_DRM_AMD_DC_SI configuration option is added, default setting is disabled
(v2) Hainan is not supported, description updated accordingly
Tested with HD7750 (Cape Verde) and HD7950 (Tahiti)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 chipsets do not support HW rotation
[How]
rotation property is created for Bonaire and later
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With all DCE6 specific macros, register, masks in place
dce60_resource.c may use them and become independent from DCE8 headers
[How]
(v1) Changelog:
- use DCE6 headers for registers and masks, remove the DC8 headers
- remove 7th Display Controller/Encoder register instances (DCE6 has only 6)
- use DCE6 specific watermark programming registers (DPG_PIPE_ARBITRATION_CONTROL3)
- use DCE6 specific input pixel processing registers shift/mask
- use DCE6 specific transform registers shift/mask
- use DCE6 specific link encoder registers shift/mask
- use DCE6 specific output pixel processing registers shift/mask
- use DCE6 specific audio registers shift/mask
- use DCE6 specific dmcu registers shift/mask
- use DCE6 specific hwseq registers shift/mask
- use DCE6 specific mem input registers shift/mask
(v2) Changelog:
- use DCE6 ad hoc dce60_mem_input_construct() function
- use DCE6 ad hoc dce60_transform_construct() function
(v3) Changelog:
- use DCE6 ad hoc dce60_ipp_construct() function
(v4) Changelog:
- use DCE6 ad hoc dce60_link_encoder_construct() function
(v5) Changelog:
- use DCE6 ad hoc dce60_opp_construct() function
(v6) Changelog:
- use DCE6 ad hoc dce60_audio_create() function
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has CRTC_PREFETCH_EN bit in CRTC_CONTROL register
DCE6 has no CRTC_LEGACY_REQUESTOR_EN bit in CRTC_START_LINE_CONTROL register
DCE6 has no CRTC_CRC_CNTL register
[How]
Modify dce60_timing_generator_enable_advanced_request() function
Add dce60_configure_crc() function and dce60_is_tg_enabled() kept as static
Use dce60_configure_crc() function in dce60_tg_funcs
v2: remove unused variable (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
kernel WARNING due to use of .cursor_lock = dce_pipe_control_lock inherited by dce110
[How]
DCE6 set .cursor_lock = dce60_pipe_control_lock
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no bottom_pipe and no Blender HW
DCE6 needs 'blank_target' set to false in order to turn on the display
DCE6 has a specific dce60_pipe_control_lock() fuction that is a no op
[How]
Add DCE6 specific functions with needed private dce60_* dependent fuctions
Comment DCE6 specific CTRC program visibility implementation
Fix a typo in the initial header includes comment 's/DCE8/DCE6/g'
Use dce60_apply_ctx_for_surface() in dce60_hw_sequencer_construct
Use dce60_pipe_control_lock() in dce60_hw_sequencer_construct
v2: add missing return type (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has specific SCL_HORZ_FILTER_INIT_{LUMA_RGB,CHROMA} registers
In DCE6 h_init_luma and h_init_chroma initialization is required
Some DCE6 specific SCL_{HORZ,VERT}_FILTER_CONTROL masks were not listed
[How]
Add the registers and masks in dce_transform.h
Add DCE6 specific struct sclh_ratios_inits in dce_transform.h
Add dce60_calculate_inits() function
Add dce60_program_scl_ratios_inits() function
Fix dce60_transform_set_scaler() function
v2: remove unused variable (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no SCL_MODE and no SCL_{HORZ,VERT}_FILTER_INIT registers
DCE6 has no SCL_BOUNDARY_MODE bit in SCL_CONTROL register
DCE6 has Line Buffer programming registers (DC_LB_MEMORY_SPLIT,DC_LB_MEM_SIZE)
DCE6 DATA_FORMAT register has only INTERLEAVE_EN bit
DCE6 has no Out Clamp Control programming registers (OUT_CLAMP_CONTROL_*)
[How]
Add DCE6 specific macros definitions for XFM registers and masks
Add DCE6 specific registers to dce_transform_registers struct
Add DCE6 specific masks to dce_transform_mask struct
DCE6 XFM macros/structs changes will avoid buiding errors when using DCE6 headers
Add dce60_setup_scaling_configuration() w/o missing Scaling registers/bit programming
Add dce60_transform_set_scaler() using DCE6 Line Buffer programming registers
Add dce60_program_bit_depth_reduction() w/o Out Clamp Control programming
Add dce60_transform_set_pixel_storage_depth() use dce60_program_bit_depth_reduction()
Use dce60_transform_set_scaler() in dce60_transform_funcs
Use dce60_transform_set_pixel_storage_depth() in dce60_transform_funcs
Add DCE6 specific dce60_transform_construct
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no FMT_TRUNCATE_MODE bit in FMT_BIT_DEPTH_CONTROL register
DCE6 has no FMT_CLAMP_COMPONENT_{R,G,B} registers
DCE6 has no FMT_SUBSAMPLING_{MODE,ORDER} bits in FMT_CONTROL register
[How]
Add DCE6 specific macros definitions for OPP registers and masks
DCE6 OPP macros will avoid buiding errors when using DCE6 headers
Add dce60_set_truncation() w/o FMT_TRUNCATE_MODE bit programming
Add dce60_opp_set_clamping() w/o Format Clamp Component programming
Add dce60_opp_program_fmt() w/o Format Subsampling bits programming
Add dce60_opp_program_bit_depth_reduction() with dce60_set_truncation
Use dce60_opp_program_fmt() in dce60_opp_funcs
Use dce60_opp_program_bit_depth_reduction() in dce60_opp_funcs
Add DCE6 specific dce60_opp_construct
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has DPG_PIPE_ARBITRATION_CONTROL3 register for Line Buffer watermark selection
DCE6 has STUTTER_EXIT_SELF_REFRESH_WATERMARK_MASK mask for Stutter watermark selection
DCE6 has NB_PSTATE_CHANGE_WATERMARK_MASK mask for North Bridge watermark selection
DCE6 has no GRPH_MICRO_TILE_MODE mask
DCE6 has no HW_ROTATION register
[How]
Add DCE6 specific macros definitions for MI registers and masks
Add DCE6 specific registers to dce_mem_input_registers struct
Add DCE6 specific masks to dce_mem_input_masks struct
DCE6 MI macros/structs changes will avoid buiding errors when using DCE6 headers
Add dce60_program_urgency_watermark() function
Add dce60_program_nbp_watermark() function
Add dce60_program_stutter_watermark() function
Add dce60_mi_program_display_marks() function w/ new DCE6 watermark programming
Add DCE6 specific tiling programming and modify DCE8 case
Add dce60_program_size() fuction w/o Rotation processing
Add dce60_mi_program_surface_config() fuction
Use dce60_mi_program_display_marks() in dce60_mi_funcs
Use dce60_mi_program_surface_config() in dce60_mi_funcs
Add DCE6 specific dce60_mem_input_construct
v2: remove unused variable (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no DP_DPHY_SCRAM_CNTL register
[How]
Add DCE6 specific macros definitions for LE registers
DCE6 LE macros will avoid buiding errors when using DCE6 headers
Add dce60_set_dp_phy_pattern_hbr2_compliance_cp2520_2() w/o Scramble Control programming
Add dce60_set_dp_phy_pattern_passthrough_mode() w/o Scramble Control programming
Add dce60_configure_encoder() w/o Scramble Control programming
Add dce60_link_encoder_enable_dp_output() w/ dce60_configure_encoder
Add dce60_link_encoder_enable_dp_mst_output() w/ dce60_configure_encoder
Add dce60_link_encoder_dp_set_phy_pattern() w/ dce60_set_dp_phy_pattern_passthrough_mode
Use dce60_link_encoder_enable_dp_output() in dce60_lnk_enc_funcs
Use dce60_link_encoder_enable_dp_mst_output() in dce60_lnk_enc_funcs
Use dce60_link_encoder_dp_set_phy_pattern() in dce60_lnk_enc_funcs
Add DCE6 specific dce60_link_encoder_construct
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 does not have CURSOR2_DEGAMMA_MODE bit in DEGAMMA_CONTROL register
[How]
Add DCE6 specific macros definitions for IPP masks
DCE6 IPP macros will avoid buiding errors when using DCE6 headers
Add dce60_ipp_set_degamma() function w/o Cursor2 Degamma programming
Use dce60_ipp_set_degamma() in ipp_funcs dce60_ipp_funcs
Add DCE6 specific dce60_ipp_construct
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no BLND_CONTROL register for Blender HW programming
DCE6 has no BLND_V_UPDATE_LOCK register for Pipe Locking
[How]
Add DCE6 specific macros definitions for HWSEQ registers and masks
DCE6 HWSEQ macros will avoid buiding errors when using DCE6 headers
Add dce60_pipe_control_lock() stub with no op
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no SMU_INTERRUPT_CONTROL register, but it's used for DCN10 and later
[How]
Add DCE6 specific macros definitions for DMCU registers and masks
DCE6 DMCU macros will avoid buiding errors when using DCE6 headers
There is no other change needed in dce_dcmu
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no DCCG_AUDIO_DTO2_USE_512FBR_DTO mask in DCCG_AUDIO_DTO_SOURCE register
[How]
Add DCE6 specific macros definitions for AUD masks
DCE6 AUD macros will avoid buiding errors when using DCE6 headers
Add dce60_aud_wall_dto_setup() w/o 512*Fs programming
Use dce60_aud_wall_dto_setup() in dce60_funcs
Add DCE specific dce60_audio_create
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Issue in the Mouse cursor size in Linux Desktop Environments
[How]
In DCE6 dc->caps.max_cursor_size need to be set as 64 instead of 128
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(v1) Changelog
[Why]
After commit c69dd2d "drm/amd/display: Refactor clk_mgr functions"
dc/clk_mgr requires these changes to add SI parts support
Necessary to avoid hitting default: ASSERT(0); /* Unknown Asic */
that would cause kernel freeze
[How]
Add case statement for FAMILY_SI chipsets
(v2) Changelog
[Why]
DCE6 has no DPREFCLK_CNTL register
[How]
Add DCE6 specific macros definitions for CLK registers and masks
Add DCE6 specific dce60/dce60_clk_mgr.c for DCE6 customization
Code style: reuse all the public functions in dce100/dce_clk_mgr.h header
Code style: use dce60_* static functions as per other DCE implementations
Add dce60_get_dp_ref_freq_khz() w/o using DPREFCLK_CNTL register
Use dce60_get_dp_ref_freq_khz() function in dce60_funcs
Add DCE6 specific dce60_clk_mgr_construct
dc/clk_mgr/dce_clk_mgr.c: use dce60_clk_mgr_construct for FAMILY_SI chipsets
Add Makefile rules for dce60_clk_mgr.o target conditional to CONFIG_DRM_AMD_DC_SI
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
amdgpu_dm.c requires changes for SI chipsets init and irq handlers registration
[How]
SI support: load_dmcu_fw(), amdgpu_dm_initialize_drm_device(), dm_early_init()
Add DCE6 specific dce60_register_irq_handlers() function
(v1) NOTE: As per Kaveri and older amdgpu.dc=1 kernel cmdline is required
(v2) fix for bc011f9 ("drm/amdgpu: Change SI/CI gfx/sdma/smu init sequence")
remove CHIP_HAINAN support since it does not have physical DCE6 module
(v3) fix vblank irq support for DCE6 using ad hoc dce60_register_irq_handlers()
replicating for vblank irq the behavior of dce110_register_irq_handlers()
as per commit b57de80 ("drm/amd/display: Register on VLBLANK ISR.")
(v4) updated due to following kernel 5.2 commit:
b2fddb13 ("drm/amd/display: Drop underlay plane support")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
irq service requires changes for DCE6 support
[How]
(v1) DCE6 targets are added replicating existing DCE8 implementation.
due to missing CRTC_VERTICAL_INTERRUPT0_CONTROL registers/masks,
dce/dce_8_0_{d,sh_mask}.h used instead of dce/dce_6_0_{d,sh_mask}.h
(v2) DCE6 headers used adding the necessary vblank irq registers
(INT_MASK and VBLANK_STATUS) and vblank irq masks as implemented
in amdgpu driver.
Add vblank_irq_info_funcs_dce60 with .set and .ack as per commit
b10d51f ("drm/amd/display: Add interrupt entries for VBLANK isr.")
and use it in vblank_int_entry(reg_num) macro definition
(v3) updated due to following kernel 5.3 commit:
4fc4dca ("drm/amd: drop use of drmp.h in os_types.h")
(v4) updated due to following kernel 5.6 commit:
d9e3267 ("drm/amd/display: cleanup of construct and destruct funcs")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
hw_factory.c requires changes for DCE6 support
[How]
DCE6 targets added replicating and adapting existing DCE8 implementation.
(v2) changes due to following commit:
91db931 ("drm/amd/display: refactor gpio to allocate hw_container in constructor")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
command_table_helper.c requires changes for DCE6 support
[How]
DCE6 targets added replicating and adapting the existing DCE8 implementation.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
resource_parse_asic_id() and dc_create_resource_pool() are missing SI/DCE6 cases
[How]
SI/DCE6 cases support added using existing DCE8 implementation as a reference
(v2) updated due to following kernel 5.2 commit:
d9673c9 ("drm/amd/display: Pass init_data into DCN resource creation")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 chipsets have a lot in common with DCE8, let's start from this
[How]
DCE6 targets are added replicating existing DCE8 implementation.
NOTE: dce_8_0_{d,sh_mask}.h headers used instead of dce_6_0_{d,sh_mask}.h
initial build prototype due to missing DCE6 macros/registers/masks
DCE6 specific macros/registers/masks will be added with later commits
(v2b) removed dce_version cases in dc/dce/dce_clock_source.c and
updated dce60 due to following kernel 5.0 commits:
24f7dd7 ("drm/amd/display: move pplib/smu notification to dccg block")
9566b67 ("drm/amd/display: remove safe_to_lower flag from dc, use 2 functions instead")
4244381 ("drm/amd/display: clean up base dccg struct")
4c5e8b5 ("drm/amd/display: split dccg clock manager into asic folders")
84e7fc0 ("drm/amd/display: rename dccg to clk_mgr")
77f6916 ("drm/amd/display: Remove duplicate header")
9f7ddbe ("drm/amd/display: fix optimize_bandwidth func pointer for dce80")
4ece61a ("drm/amd/display: set clocks to 0 on suspend on dce80")
(v3b) updated dce60 due to following kernel 5.1 commits:
380604e ("drm/amd/display: Use 100 Hz precision for pipe pixel clocks")
32e6136 ("drm/amd/display: Fix 64-bit division for 32-bit builds")
1877ccf ("drm/amd/display: Change from aux_engine to dce_aux")
c69dffa ("drm/amd/display: fix eDP fast bootup for pre-raven asic")
(v4b) updated dce60 due to following kernel 5.2 commits:
e5c4197 ("drm/amd/display: Add plane capabilities to dc_caps")
813d20d ("drm/amd/display: Fix multi-thread writing to 1 state")
ea36ad3 ("drm/amd/display: expand plane caps to include fp16 and scaling capability")
afcd526 ("drm/amd/display: Add fast_validate parameter")
(v5b) updated dce60 due to following kernel 5.3 commits:
e7e10c4 ("drm/amd/display: stop external access to internal optc sync params")
78cc70b ("drm/amd/display: Engine-specific encoder allocation")
dc88b4a ("drm/amd/display: make clk mgr soc specific")
4fc4dca ("drm/amd: drop use of drmp.h in os_types.h")
(v6b) updated dce60 due to following kernel 5.4 commits:
54a9bcb ("drm/amd/display: Fix a typo - dce_aduio_mask --> dce_audio_mask")
9adc805 ("drm/amd/display: make firmware info only load once during dc_bios create")
(v7b) updated dce60 due to following kernel 5.5 commits:
cabe144 ("drm/amd/display: memory leak")
8276dd8 ("drm/amd/display: update register field access mechanism")
f6040a4 ("drm/amd/display: configurable aux timeout support")
bf7f5ac ("drm/amd/display: map TRANSMITTER_UNIPHY_x to LINK_REGS_x")
(v8b) updated dce60 due to following kernel 5.6 commits:
d9e3267 ("drm/amd/display: cleanup of construct and destruct funcs")
f42ea55 ("drm/amd/display: add separate of private hwss functions")
(v9b) updated dce60 due to following kernel 5.8 commits:
bba8289 ("drm/amd/display: code clean up in dce80_hw_sequencer.c")
904fb6e ("drm/amd/display: move panel power seq to new panel struct")
d4caa72 ("drm/amd/display: change from panel to panel cntl")
(v10) Fix up PLL handling for DCE6:
DCE6.0 supports 2 PLLs. DCE6.1 supports 3 PLLs. (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Asic info for SI parts need to be preliminarly added
[How]
Asics info retrieved from si_id.h in https://github.com/GPUOpen-Tools/CodeXL
Tree path:
./CodeXL/Components/ShaderAnalyzer/AMDTBackEnd/Include/Common/asic_reg/si_id.h
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Use DCN21 functions instead of DCE110
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently navy_flounder is using sienna_cichlid_dmcub.bin.
[How]
Create a seperate define so navy_flounder will use its own firmware.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some monitors could suffer symbol unlock but cannot send HPD IRQ to
notic source device to handle link loss. This makes monitor stuck in
abnormal status and causes black screen.
[How]
According to the suggestion from scalar vendor, to check lane status
again after link training done. That can improve the comaptibility
from current production monitors.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dcn3_update_clocks there are situations where dppclk is not
lowered (i.e. stays the same), but DTO still needs to be increased
before we program pipe frontend (i.e. in prepare_bandwidth). If we
don't program the new DTO value before we program the pipe,
we will underflow as soon as the pipe lock is released until the
next call to dcn3_update_clocks where the DTO is updated.
[How]
Remove dppclk check before programming new DTO value.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Fix naming and return bits rather than bytes per pixel for
naming consistency. Because registers return Bytes per pixel,
but DSC Config structure is expecting bits per pixel as input.
So when returning the value convert from bytes into bits.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Struct dcn_dsc_state is used for reading current state
and parameters of DSC on a pipe, the target rate parameter
uses bytes per pixel even though its reading BITS_PER_PIXEL
register.
[How]
Changing it to Bits Per Pixel for consistency.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change replaces older looping code in favor of these functions.
[How]
There are built in functions for extracting global sync params
during mode validation now.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when GPU hang, driver has multi-paths to enter amdgpu_device_gpu_recover,
the atomic adev->in_gpu_reset and hive->in_reset are used to avoid
re-entering GPU recovery.
During GPU reset and resume, it is unsafe that other threads access GPU,
which maybe cause GPU reset failed. Therefore the new rw_semaphore
adev->reset_sem is introduced, which protect GPU from being accessed by
external threads during recovery.
v2:
1. add rwlock for some ioctls, debugfs and file-close function.
2. change to use dqm->is_resetting and dqm_lock for protection in kfd
driver.
3. remove try_lock and change adev->in_gpu_reset as atomic, to avoid
re-enter GPU recovery for the same GPU hang.
v3:
1. change back to use adev->reset_sem to protect kfd callback
functions, because dqm_lock couldn't protect all codes, for example:
free_mqd must be called outside of dqm_lock;
[ 1230.176199] Hardware name: Supermicro SYS-7049GP-TRT/X11DPG-QT, BIOS 3.1 05/23/2019
[ 1230.177221] Call Trace:
[ 1230.178249] dump_stack+0x98/0xd5
[ 1230.179443] amdgpu_virt_kiq_reg_write_reg_wait+0x181/0x190 [amdgpu]
[ 1230.180673] gmc_v9_0_flush_gpu_tlb+0xcc/0x310 [amdgpu]
[ 1230.181882] amdgpu_gart_unbind+0xa9/0xe0 [amdgpu]
[ 1230.183098] amdgpu_ttm_backend_unbind+0x46/0x180 [amdgpu]
[ 1230.184239] ? ttm_bo_put+0x171/0x5f0 [ttm]
[ 1230.185394] ttm_tt_unbind+0x21/0x40 [ttm]
[ 1230.186558] ttm_tt_destroy.part.12+0x12/0x60 [ttm]
[ 1230.187707] ttm_tt_destroy+0x13/0x20 [ttm]
[ 1230.188832] ttm_bo_cleanup_memtype_use+0x36/0x80 [ttm]
[ 1230.189979] ttm_bo_put+0x1be/0x5f0 [ttm]
[ 1230.191230] amdgpu_bo_unref+0x1e/0x30 [amdgpu]
[ 1230.192522] amdgpu_amdkfd_free_gtt_mem+0xaf/0x140 [amdgpu]
[ 1230.193833] free_mqd+0x25/0x40 [amdgpu]
[ 1230.195143] destroy_queue_cpsch+0x1a7/0x270 [amdgpu]
[ 1230.196475] pqm_destroy_queue+0x105/0x260 [amdgpu]
[ 1230.197819] kfd_ioctl_destroy_queue+0x37/0x70 [amdgpu]
[ 1230.199154] kfd_ioctl+0x277/0x500 [amdgpu]
[ 1230.200458] ? kfd_ioctl_get_clock_counters+0x60/0x60 [amdgpu]
[ 1230.201656] ? tomoyo_file_ioctl+0x19/0x20
[ 1230.202831] ksys_ioctl+0x98/0xb0
[ 1230.204004] __x64_sys_ioctl+0x1a/0x20
[ 1230.205174] do_syscall_64+0x5f/0x250
[ 1230.206339] entry_SYSCALL_64_after_hwframe+0x49/0xbe
2. remove try_lock and introduce atomic hive->in_reset, to avoid
re-enter GPU recovery.
v4:
1. remove an unnecessary whitespace change in kfd_chardev.c
2. remove comment codes in amdgpu_device.c
3. add more detailed comment in commit message
4. define a wrap function amdgpu_in_reset
v5:
1. Fix some style issues.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Suggested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com>
Suggested-by: Lijo Lazar <Lijo.Lazar@amd.com>
Suggested-by: Luben Tukov <luben.tuikov@amd.com>
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable result is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge v5.8-rc6 into drm-next
I've got a silent conflict + two trees based on fixes to merge.
Fixes a silent merge with amdgpu
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix below warnings reported by coccicheck:
./drivers/gpu/drm/amd/display/dc/clk_mgr/dcn30/dcn30_clk_mgr.c:557:2-7: WARNING: NULL check before some freeing functions is not needed.
Fixes: 4d55b0dd1c ("drm/amd/display: Add DCN3 CLK_MGR")
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-next-5.9-2020-07-17:
amdgpu:
- SI UVD/VCE clock support
- Updates for Sienna Cichlid
- Expose drm rotation property
- Atomfirmware updates for renoir
- updates to GPUVM hub handling for different register layouts
- swSMU restructuring and cleanups
- RAS fixes
- DC fixes
- mode1 reset support for Sienna Cichlid
- Add support for Navy Flounder GPUs
amdkfd:
- Add SMI events watch interface
UAPI:
- Add amdkfd SMI events watch interface
Userspace which uses this interface:
2235ede34c
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200717132022.4014-1-alexander.deucher@amd.com
drm_atomic_crtc_check enforces that ::active can only be true if
::enable is as well.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v3:
* Rebase (Manasi)
v2:
* Rebase (Manasi)
As both VRR min and max are already part of drm_display_info,
drm can expose this VRR range for each connector.
Hence this logic should move to core DRM.
This reverts commit 727962f030.
Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: AMD gfx <amd-gfx@lists.freedesktop.org>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Implement an interface to obtain plane size caps
[How]
Add min_width, min_height fields to dc_plane_cap structure.
Set values to 16x16 for discrete ASICs, and 64x64 for others.
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Fix build error by protecting code with config guard
to enable building amdgpu without CONFIG_DRM_AMD_DC_DCN
enabled. This option is disabled by default for allmodconfig.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Accessing dcn20_add_dsc_to_stream_resource directly
causes build failure for configuration which has
CONFIG_DRM_AMD_DC_DCN disabled. Fix this by
calling the corresponding function exposed via dc
resource functions.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On DCN20, Some features would not be activated when ALLM was turned on.
TV seemed to activate only the latest info packet sent, and the ALLM
info packet was sent after the VSIF info packet.
The packet indices was also inconsistent between DCN10 and DCN20.
[how]
Change the packet indices of DCN20 to match those of DCN10.
This makes them consistent and also makes the vendor info packet
be sent after the hfvsif info packet.
Signed-off-by: Naveed Ashfaq <Naveed.Ashfaq@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn20_add_dsc_to_stream_resource is accessed in amdgpu_dm directly.
This creates build error for configuration with DCN disabled.
[How]
Make the function available through a resource pool function so
that dcn20 function need not be called directly.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The capability fields are reserved for DSC branch
only to report the capability related to the
branch's DSC decoder.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With ABM implemented on DMUB the ABM enablement
shoudn't be solely rely on dmcu. Otherwise it won't work
if dmcu is disabled.
[How]
1. Decouple dmcub config copy from dmcu iram copy.
2. Set abm connector property if either dmcu or dmub enabled.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To support V3
[How]
Generate new VSIF for V3
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to add new parameters to debugfs logging so
we will know what parameters DSC is using for
debug purposes. So we are adding a read function
in debugfs to read DSC status registers
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Scaler vendor confirmed the 5ms was not helpful so no point in keeping
it.
[How]
Revert 5ms delay after setting training pattern.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Maximum code sharing.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Add ckoenig as dma-buf maintainer.
- Revert invalid fix for dma-fence-chain, and fix selftest.
- Add fixmes to amifb about APUS support.
- Use array3_size in fbcon_prepare_logo, and struct_size() in alloc_apertures.
- Fix leaks in neofb, fb/savage and omapfb.
- Other small fixes to fb code.
- Convert some dt bindings to schema for some panels, and fix simple-framebuffer dt example.
Core Changes:
- Add DRM_FORMAT_MOD_GENERIC_16_16_TILE as alias to DRM_FORMAT_MOD_SAMSUNG_16_16_TILE,
as it can be used more generic.
- Add support for multiple DispID extension blocks in edid.
- Use https instead of http for some of the urls.
- Use drm_* macros for logging in mipi-dsi and fb-helper.
- Further cleanup ttm_mem_reg handling.
- Remove duplicated words in comments.
Driver Changes:
- Use __drm_atomic_helper_crtc_reset in all atomic drivers.
- Add Amlogic Video FBC support to meson and fourcc to core.
- Refactor hisilicon's hibmc_drv_vdac.
- Create a TXP CRTC for vc4.
- Rework cursor support in ast.
- Fix runtime PM in STM.
- Allow bigger cursors in vkms.
- Cleanup sg handling in radeon and amdgpu, and stop creating dummy
gtt nodes with ttm fixed.
- Rework crtc handling in mgag200.
- Miscellaneous small fixes to meson, vgem, bridge/dw-hdmi,
panel/auo,b116xw03, panel/LG LB070WV8, lima, bridge/sil_sii8620,
virtio, tilcdc.
-----BEGIN PGP SIGNATURE-----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=XKYB
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-07-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.9:
UAPI Changes:
Cross-subsystem Changes:
- Add ckoenig as dma-buf maintainer.
- Revert invalid fix for dma-fence-chain, and fix selftest.
- Add fixmes to amifb about APUS support.
- Use array3_size in fbcon_prepare_logo, and struct_size() in alloc_apertures.
- Fix leaks in neofb, fb/savage and omapfb.
- Other small fixes to fb code.
- Convert some dt bindings to schema for some panels, and fix simple-framebuffer dt example.
Core Changes:
- Add DRM_FORMAT_MOD_GENERIC_16_16_TILE as alias to DRM_FORMAT_MOD_SAMSUNG_16_16_TILE,
as it can be used more generic.
- Add support for multiple DispID extension blocks in edid.
- Use https instead of http for some of the urls.
- Use drm_* macros for logging in mipi-dsi and fb-helper.
- Further cleanup ttm_mem_reg handling.
- Remove duplicated words in comments.
Driver Changes:
- Use __drm_atomic_helper_crtc_reset in all atomic drivers.
- Add Amlogic Video FBC support to meson and fourcc to core.
- Refactor hisilicon's hibmc_drv_vdac.
- Create a TXP CRTC for vc4.
- Rework cursor support in ast.
- Fix runtime PM in STM.
- Allow bigger cursors in vkms.
- Cleanup sg handling in radeon and amdgpu, and stop creating dummy
gtt nodes with ttm fixed.
- Rework crtc handling in mgag200.
- Miscellaneous small fixes to meson, vgem, bridge/dw-hdmi,
panel/auo,b116xw03, panel/LG LB070WV8, lima, bridge/sil_sii8620,
virtio, tilcdc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8b360d65-f228-9286-d247-3004156a5254@linux.intel.com
Plumb DC support for navy flounder through.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Failing to allocate a transfer function during stream construction leads
to a null pointer dereference
[How]
Handle the failed allocation by failing the stream construction
Cc: stable@vger.kernel.org
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
amdgpu_dm->backlight_caps is for single eDP only. the caps are upddated
for very connector. Real eDP caps will be overwritten by other external
display. For OLED panel, caps->aux_support is set to 1 for OLED pnael.
after external connected, caps+.aux_support is set to 0. This causes
OLED backlight adjustment not work.
[How]
within update_conector_ext_caps, backlight caps will be updated only for
eDP connector.
Cc: stable@vger.kernel.org
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prevents a warning in the MST create connector case.
v2: create global fake encoders rather per connector fake encoders
to avoid running out of encoder indices.
v3: use the actual number of crtcs on the asic rather than the max
to conserve encoders.
v4: v3 plus missing hunk I forgot to git add.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1108
Fixes: c6385e503a ("drm/amdgpu: drop legacy drm load and unload callbacks")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.7.x
The "stream" pointer can't be NULL and it's dereferenced on the line
before so the check doesn't make sense.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
CRC capture doesn't work when the active plane count is 0 since we
currently tie both vblank and pageflip interrupts to active_plane_count
greater than 0.
[How]
The frontend is what generates the vblank interrupts while the backend
is what generates pageflip interrupts. Both have a requirement for
the CRTC to be active, so control the overall interrupt state based
on that instead.
Pageflip interrupts need to be enabled based on active plane count, but
we actually rely on power gating to take care of disabling the interrupt
for us on pipes that can be power gated.
For pipes that can't be power gated it's still fine to leave it enabled
since the interrupt only triggers after the address has been written
to that particular pipe - which we won't be doing without an active
plane.
The issue we had before with this setup was that we couldn't force
the state back on. We were essentially manipulating the refcount
to enable or disable as needed in a two pass approach.
However, there is a function that solves this problem more elegantly:
amdgpu_irq_update() will unconditionally call the set based on what it
thinks the current enablement state is.
This leaves two future TODO items for our IRQ handling:
- Disabling IRQs in commit tail instead of atomic commit
- Mapping the pageflip interrupt to VUPDATE or something that's tied to
the frontend instead of the backend since the mapping to CRTC is not
correct
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling the debugfs for CRC capture we hit assertions caused by
register address and field masks and shifts missing.
[How]
We want these registers programmed, so add in the SRI/SF entries for
this register.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Failing to allocate a transfer function during stream construction leads
to a null pointer dereference
[How]
Handle the failed allocation by failing the stream construction
Cc: stable@vger.kernel.org
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move code for parsing debugfs input into an array of int parameters by
specifying the max number of expected parameters
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our validation is a known mess with actual validation mixed with
topology configuration. This change makes sure topolgical validation is
completed before any topology changes are made so we do not run into
issues where we merge and split a pipe over the course of a single call.
v2: Squash in compilation fix
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new calculated dispclk, dppclk are stored in
context->bw_ctx.bw.dcn.clk.dispclk_khz, dppclk_khz. Current dispclk,
dppclk are from dc->clk_mgr->clks.dispclk_khz. dcn_validate_bandwidth
compute new dispclk, dppclk. dispclk will put in use after
optimize_bandwidth when ramp_up_dispclk_with_dpp is called. There are
two places for dppclk be put in use. One location is the same as the
location as dispclk. Another is within update_dchubp_dpp which happens
between pre_bandwidth and optimize_bandwidth. dppclk updated within
update_dchubp_dpp will cause new clock values of dispclk and dppclk not
be in use at the same time. when clocks are decreased, this may cause
dppclk is lower than current configuration and let pipe stuck. for
example, eDP + external dp, change resolution of DP from 1920x1080x144hz
to 1280x960x60hz.
before change: dispclk = 337889 dppclk = 337889
change mode, dcn_validate_bandwidth calculate
dispclk = 143122 dppclk = 143122
update_dchubp_dpp be executed before dispclk be updated,
dispclk = 337889, but dppclk use new value dispclk /2 =
168944. this will cause pipe pstate warning issue.
[How]
between pre_bandwidth and optimize_bandwidth, while dispclk is going to
be decreased, keep dppclk = dispclk
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
amdgpu_dm->backlight_caps is for single eDP only. the caps are upddated
for very connector. Real eDP caps will be overwritten by other external
display. For OLED panel, caps->aux_support is set to 1 for OLED pnael.
after external connected, caps+.aux_support is set to 0. This causes
OLED backlight adjustment not work.
[How]
within update_conector_ext_caps, backlight caps will be updated only for
eDP connector.
Cc: stable@vger.kernel.org
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when ppt disabled, the watermark doesn't get fine tune causing
underflow.
[How]
It is a temporary solution to reduce sr_xxx_time by 3 us when ppt
disable.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless systems, if set mode is not called, hardware will not be
powered down on boot, causing HW/SW discrepancies. Powering down
hardware on boot will ensure SW state is accurate.
[HOW]
Set a timer callback on boot for 10 seconds. If set mode is not called
within that time, power down hardware. Otherwise, do not power down.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prevents a warning in the MST create connector case.
v2: create global fake encoders rather per connector fake encoders
to avoid running out of encoder indices.
v3: use the actual number of crtcs on the asic rather than the max
to conserve encoders.
v4: v3 plus missing hunk I forgot to git add.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1108
Fixes: c6385e503a ("drm/amdgpu: drop legacy drm load and unload callbacks")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid s3 faild at the first cycle on renoir platform, it needs to
revert this patch:
drm/amd/display: add mechanism to skip DCN init
Signed-off-by: changfeng <Changfeng.Zhu@amd.com>
Ackedy-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN3 has two gamut remap matrices. When using CSC adjustment the CM
remap is set to bypass and MPCC remap is used. However to bypass CM
some state in the context is modified and not restored correctly
resulting in subsequent calls to disable MPCC remap as well.
[How]
Fix logic for save/restore of remap enable flag when programming MPCC
remap matrix.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Soft hangs occur when FreeSync is engaged since we utilize VUPDATE
(which doesn't fire when holding the pipe lock) to send back vblank
events when FreeSync is active.
[How]
The alternative (working) interrupt source for this mechanism is
VUPDATE_NO_LOCK. We already use this all other DCN revisions so align
dcn30 with those as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RENOIR loads dmub fw not dmcu, check dmcu only will prevent loading iram,
it breaks backlight control.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=208277
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
To support inbox1 in CW4 we need to actually program CW4 instead of
region 4 for newer firmware.
This is done correctly on DCN20/DCN21 but this code wasn't added to
DCN30.
[How]
Copy over the missing code. It doesn't need address translation since
DCN30 uses virtual addressing.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This field is missing for dcn3 so add it from dcn20.
enc2_set_dynamic_metadata() trys to sets this and we get a
generic_reg warning since the mask is not defined.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to be able to see SMU messages sent and their responses
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we don't explicitly send a request for a minimum PHYCLK, and
we hope that the dependencies other clocks have will raise PHYCLK when
needed.
[How]
- new clk_mgr function to keep track of PHYCLK requirements
- request maximum requirement across all links
- remove PHYCLK from clock state comparator, as it doesn't come from DML
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VSC infoframe is needed for PSR. Previously only DMCU controller
supported PSR. Now DMUB also implements PSR.
[How]
Remove VSC infoframe dependency on DMCU.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current DAL behaviour is to not send VSIF if mode does not support VRR
(ie. FS range is < 10Hz). However, we should still set FS Native Color
Active bit in some unsupported mode cases.
[How]
Remove check for if VRR is supported before building infopacket.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver re-initialize registers already set in FW
[How]
Transfer init to FW
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Print scaling parameters as they are calculated in diags.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now also comes with the added benefit of doing a drm_crtc_vblank_off(),
which means vblank state isn't ill-defined and fail-y at driver load
before the first modeset on each crtc.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Stylon Wang <stylon.wang@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612160056.2082681-2-daniel.vetter@ffwll.ch
The variable result is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Changes that are fast don't require updating DLG parameters making
this call unnecessary. Considering this is an expensive call it should
not be done on every flip.
DML touches clocks, p-state support, DLG params and a few other DC
internal flags and these aren't expected during fast. A hang has been
reported with this change when called on every flip which suggests that
modifying these fields is not recommended behavior on fast updates.
[How]
Guard the validation to only happen if update type isn't FAST.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1191
Fixes: a24eaa5c51 ("drm/amd/display: Revalidate bandwidth before commiting DC updates")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's otherwise properly supported, just needs exposing to userspace.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In case of certain display configurations we want to allow max detile
buffer utilization by using 4 to 1 mpc combine
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Register key for AE or QA do regression test. New edid status for
check.
[How]
Add register key edid_read_retry_times.
Add new edid status EDID_FALL_BACK.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Header Changes]
- Add command for notification of active streams to DMUB
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In cases where refresh range is slightly below 10, FreeSync is not
active or supported. Need to round values before checking refresh range
in order to have FreeSync supported in these cases.
[How]
Remove redundant values and round values before checking valid refresh range.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For special DP convert VGA dongle, core_link_read_dpcd for
DP_DOWNSTREAM_PORT_0 always return fail, then dongle_type will be set to
DISPLAY_DONGLE_NONE, which will cause desktop resolution abnormal.
[How]
If dpcd for DP_DOWNSTREAM_PORT_0 read fail, skip set dongle_type =
DISPLAY_DONGLE_NONE.
Signed-off-by: jinlong zhang <jinlong.zhang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU may return error code to driver, but driver only check if response
is OK.
[How]
Check SMU response instead of reg_wait, assert in case of reponse isn't
OK.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to keep the same buffer allocated for use during multiple
hardware initializations.
[How]
- allocate gpu memory buffer on clock manager construct
- free gpu memory buffer on clock manager destruct
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Debug flags are not set by default.
[How]
Set debug flags to 0
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-next-5.9-2020-07-01:
amdgpu:
- DC DMUB updates
- HDCP fixes
- Thermal interrupt fixes
- Add initial support for Sienna Cichlid GPU
- Add support for unique id on Arcturus
- Major swSMU code cleanup
- Skip BAR resizing if the bios already did id
- Fixes for DCN bandwidth calculations
- Runtime PM reference count fixes
- Add initial UVD support for SI
- Add support for ASSR on eDP links
- Lots of misc fixes and cleanups
- Enable runtime PM on vega10 boards that support BACO
- RAS fixes
- SR-IOV fixes
- Use IP discovery table on renoir
- DC stream synchronization fixes
amdkfd:
- Track SDMA usage per process
- Fix GCC10 compiler warnings
- Locking fix
radeon:
- Default to on chip GART for AGP boards on all arches
- Runtime PM reference count fixes
UAPI:
- Update comments to clarify MTYPE
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701155041.1102829-1-alexander.deucher@amd.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
The release_firmware() function is NULL tolerant so we do not need
to check for NULL param before calling it.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure we pass through ret label to unlock the mutex.
Signed-off-by: John van der Kamp <sjonny@suffe.me.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Regression was introduced where setting max bpc property has no effect
on the atomic check and final commit. It has the same effect as max bpc
being stuck at 8.
[How]
Correctly propagate max bpc with the new connector state.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Header Changes]
- Add debug flag for psr to use hw locking mgr state machine
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.
[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And set back to 400us if LTTPR feature is not enabled.
We will set 3.2ms and always enable LTTPR non transparent mode
if LTTPR feature is enabled and LTTPR is present.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Two issues:
1. Add read only operation support for query ddc data over aux.
2. Fix a bug where if read size is multiple of 16,
mot of the last read transaction will not be set to 0.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the front porch of the two timings differ, then there may not be
enough time while both streams are in vertical blank to perform a memory
clock change. This can hang the system.
[How]
Check the each streams timing.v_front_porch when determining if the two
streams are synchronizable.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
seamless boots requires split of init_hw into hw and pipes to work. This
was implemented in dcn10_init_hw but did not apply yet to dcn30.
how:
Copy over dcn10_init_hw and adapt it to dcn30 using recent changes to
dcn3. Behavior will be different in init sequence.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We try to to change new_clocks->dppclk_khz to 100000 when
new_clocks->dppclk_khz is 0
[How]
Don't change new_clocks->dppclk_khz value when new_clocks->dppclk_khz is
0
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
10K YCbCr420 does not need ODM 4:1, but it requires MPC 4 split
indicated on the flags.
[How]
Make pixel encoding and resolution size specific workaround to enable
ODM combine on YCbCr420 high resolution modes.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If a typeC to HDMI dongle supports YCbCr420 pass through and VSC
colorimetry and pixel encoding formats in the Extended Receiver
Capability, we shall allow VSC SDP to be used.
[How]
The Extended Receiver Capability field shall check the
EXTENDED_RECEIVER_CAPABILITY_FIELD_PRESENT bit in the
TRAINING_AUX_RD_INTERVAL register. Removed DPCD rev checking for VSC
SDP.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCUB firmware version is now available from firmware metadata block.
We should be passing this into dmub_srv so we can know when to apply
firmware version specific functionality like using CW4 only instead
of the REGION4.
[How]
We don't have the helpers for DM to actually extract out firmware
metadata block themselves.
We could add that and add helpers in DM to grab this, but not every
creation sequence has firmware instruction before dmub_srv_create.
Easiest way to handle this is to fill this in automatically per DM in
the place we do have it - when calculating the region parameters. But
only fill it in if DM already hasn't in case we need to override with
a specific version.
We aren't do anything firmware version specific in dmub_srv_create
today that does require fw_version, so while it's a little unituitive
to do it when calculating region parameters it works for now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Connector property output_bpc is available on DP/eDP only. New IGT tests
would benifit if this property works on HDMI.
[How]
Enable this read-only property on all types of connectors.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All YCbCr420 resolutions 5K and above have tiling and discoloration
issues. The issue can be remedied by forcing ODM combine from 5K to 8K.
10K resolution requires ODM 4:1. The mechanism of what the real problem
is, that is inherent in ODM combine programming, doesn't seem to be
pointed at singular register programming (CLK, MPC, DCSURF, etc.), and
needs more in-depth programming sequence review for these new use case
scenarios. Until then, workaround to enable ODM combine is proposed.
While it is not our policy, HW spreadsheet also recommends turning on
ODM for these scenario to lower the voltage.
[How]
Make pixel encoding and resolution size specific workaround to enable
ODM combine on YCbCr420 high resolution modes.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is using pixelclk AVFS for dppclk, that would cause issue.
[How]
To use dispclk AVFS for both dispclk and dppclk. There would choose
dppclk for request voltage when dispclk wouldn't be updated case. If
dispclk need to be updated, then it'll choose the bigger one from dppclk
and dispclk for request voltage.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If optimized init is done in FW. DCN init be skipped in driver. This
need to be communicated between driver and fw and maintain backwards
compatibility.
[How]
Use DMUB scratch 0 bit 2 to indicate optimized init done in fw and
use DMUB scatch 4 bit 0 to indicate drive supports the optimized flow
so FW will perform it.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Check max_tmds_clk_mhz firstly will restrict pixel clock under HDMI
1.4, thus HDMI2.0 port can't correctly support 4K 60Hz.
[HOW]
Fine tune the logic to check max_forum_tmds_clk_mhz firstly.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Need to check if local_sink is NULL before accessing.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC global validation can fail when userspace requests to draw large
plane without performing the clipping themselves.
This is observed in the IGT kms_plane panning tests for 4K displays
where they draw an 8K plane without any clipping while expecting only
the top 4K to be drawn.
[How]
DRM already has helpers to take care of the clipping necessary and to
mark whether a plane is visible or not, so make use of these helpers
in DM before passing the plane to DC.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Header Changes]
- Update scratch information for boot status
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_link_set_psr_allow_active() always returns true, even in the case
that PSR is not supported.
[How]
Hook up the return value of dc_link_set_psr_allow_active().
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Reviewed-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Side-by-side and Top-and-bottom stereo configurations fail DML mode
validation due to Viewport exceeded.
This is because we consider the planes as being pipe split in pipe
population so we end up doubling the viewport width, eg. from 4k to 8k.
[How]
These pipes technically aren't hsplit, so add a check for determining
whether is_hsplit should be set.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
assr is content protection for eDP, in order to use it we need to call
psp ta (dtm)
[How]
We have a enable_assr callback, hook into this and call the correct psp
cmd id to enable assr.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently DC doesn't check requested pixel clock against an EDID
specified TMDS max clock if it exists, passing modes that should fail
[HOW]
Add max TMDS clk to edid caps and perform check during validation
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc->hwss->edp_backlight_control is null, it would casue it only be off
main-link of eDP. It is not worng behavior for eDP power sequence off.
[how]
Must use hwseq->funcs.edp_backlight_control finction pointer for edp
backlight.
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The calculation of virtual channel payload would not take link settings
in account. As we calculate VCPI slots needed both PBN for stream and
also PBN per time slot. Before we would use generic PBN per time slot,
which would not change with link settings causing wrong Payload
allocation.
[how]
Provide PBN per time slot for each Virtual channel payload calculation.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hw lock manager adds the ability to lock pipe, cursor, and dig in fw.
[How]
Send hw lock command to fw to lock pipe, cursor, and dig.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when compiled with allmodconfig option, there are error
messages as below:
ERROR: modpost:
"mod_color_is_table_init"
[drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: modpost:
"mod_color_get_table"
[drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: modpost:
"mod_color_set_table_init_state"
[drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
To fix the issue, this commits removes
CONFIG_DRM_AMD_DC_DCN guard in color/makefile.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
CC: Lewis Huang <Lewis.Huang@amd.com>
CC: Aric Cyr <Aric.Cyr@amd.com>
CC: Alexander Deucher <Alexander.Deucher@amd.com>
CC: Harry Wentland <hwentlan@amd.com>
CC: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
CC: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update each p-state in the bounding box
[How]
Update states when assigning values to clocks
v2: squash in patch to set min values (Alex)
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's only applicable on newer asics. We could end up here when
using DC on older asics like SI or KV.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1170
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If there are no supported callbacks. We'll fall back to the
nominal clocks.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1170
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Used sparse(make C=1) to find these loose ends.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to update the bounding box to have more granular control of the
DCFCLK.
[How]
Setup DCFCLK to use STA values and also optimal values based on
UCLK.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Get the values from VBIOS table
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In function fill_iram_v_2, the ram_table->bright_neg_gain`s
first element [0][0] seems to be missing. This change is just
to make the code a bit readable.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
