BSpec does not show these WAs as applicable to GLK, and for CNL it
only shows them applicable for a super early pre-production stepping
we shouldn't be caring about anymore. Remove these so we can avoid
them on ICL too.
v2: Change how we check for gen9 display platforms (Ville).
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114012432.21809-1-paulo.r.zanoni@intel.com
Define IS_GEN() similarly to our IS_GEN_RANGE(). but use gen instead of
gen_mask to do the comparison. Now callers can pass then gen as a parameter,
so we don't require one macro for each gen.
The following spatch was used to convert the users of these macros:
@@
expression e;
@@
(
- IS_GEN2(e)
+ IS_GEN(e, 2)
|
- IS_GEN3(e)
+ IS_GEN(e, 3)
|
- IS_GEN4(e)
+ IS_GEN(e, 4)
|
- IS_GEN5(e)
+ IS_GEN(e, 5)
|
- IS_GEN6(e)
+ IS_GEN(e, 6)
|
- IS_GEN7(e)
+ IS_GEN(e, 7)
|
- IS_GEN8(e)
+ IS_GEN(e, 8)
|
- IS_GEN9(e)
+ IS_GEN(e, 9)
|
- IS_GEN10(e)
+ IS_GEN(e, 10)
|
- IS_GEN11(e)
+ IS_GEN(e, 11)
)
v2: use IS_GEN rather than GT_GEN and compare to info.gen rather than
using the bitmask
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-2-lucas.demarchi@intel.com
During DDB allocation, we try to distribute enough blocks for each plane
to hit the highest watermark level; if that fails, we retry each lower
level (which should require fewer blocks) until we find one that's
possible (or until the whole commit is rejected as impossible). We need
to reset our running block count when trying each lower level, otherwise
all lower levels will fail as well.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d8e8749802 ("drm/i915: Switch to level-based DDB allocation algorithm (v5)")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212191720.3706-1-matthew.d.roper@intel.com
The DDB allocation algorithm currently used by the driver grants each
plane a very small minimum allocation of DDB blocks and then divies up
all of the remaining blocks based on the percentage of the total data
rate that the plane makes up. It turns out that this proportional
allocation approach is overly-generous with the larger planes and can
leave very small planes wthout a big enough allocation to even hit their
level 0 watermark requirements (especially on APL, which has a smaller
DDB in general than other gen9 platforms). Or there can be situations
where the smallest planes hit a lower watermark level than they should
have been able to hit with a more equitable division of DDB blocks, thus
limiting the overall system sleep state that can be achieved.
The bspec now describes an alternate algorithm that can be used to
overcome these types of issues. With the new algorithm, we calculate
all plane watermark values for all wm levels first, then go back and
partition a pipe's DDB space second. The DDB allocation will calculate
what the highest watermark level that can be achieved on *all* active
planes, and then grant the blocks necessary to hit that level to each
plane. Any remaining blocks are then divided up proportionally
according to data rate, similar to the old algorithm.
There was a previous attempt to implement this algorithm a couple years
ago in bb9d85f6e9 ("drm/i915/skl: New ddb allocation algorithm"), but
some regressions were reported, the patch was reverted, and nobody
ever got around to figuring out exactly where the bug was in that
version. Our watermark code has evolved significantly in the meantime,
but we're still getting bug reports caused by the unfair proportional
algorithm, so let's give this another shot.
v2:
- Make sure cursor allocation stays constant and fixed at the end of
the pipe allocation.
- Fix some watermark level iterators that weren't handling the max
level.
v3:
- Ensure we don't leave any DDB blocks unused by using DIV_ROUND_UP+min
to calculate the extra blocks for each plane. (Ville)
- Replace a while() loop with a for() loop to be more consistent with
surrounding code. (Ville)
- Clean unattainable watermark levels with memset rather than directly
clearing the member fields. Also do the same for the transition
watermark values if they can't be achieved. (Ville)
- Drop min_disp_buf_needed calculations in skl_compute_plane_wm() since
the results are no longer needed or used. (Ville)
- Drop skl_latency[0] != 0 sanity check; both watermark methods already
account for an invalid 0 latency by returning FP_16_16_MAX. (Ville)
v4:
- Break DDB allocation loop when total_data_rate=0 rather than
alloc_size=0. If total_data_rate has dropped to 0, all remaining
planes are disabled, which isn't true for alloc_size (we might just
have not had any remaining blocks to hand out). Plus
total_data_rate=0 is the case we need to avoid to a prevent a
div-by-0. (Ville)
- s/DIV_ROUND_UP/DIV64_U64_ROUND_UP/ to prevent 32-bit breakage (Ville)
v5:
- Don't forget to move 'start' pointer forward for UV surface when
setting plane DDB boundaries. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105458
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211173107.11068-2-matthew.d.roper@intel.com
The bspec gives an if/else chain for choosing whether to use "method 1"
or "method 2" for calculating the watermark "Selected Result Blocks"
value for a plane. One of the branches of the if chain is:
"Else If ('plane buffer allocation' is known and (plane buffer
allocation / plane blocks per line) >=1)"
Since our driver currently calculates DDB allocations first and the
actual watermark values second, the plane buffer allocation is known at
this point in our code and we include this test in our driver's logic.
However we plan to soon move to a "watermarks first, ddb allocation
second" sequence where we won't know the DDB allocation at this point.
Let's drop this arm of the if/else statement (effectively considering
the DDB allocation unknown) as an independent patch so that any
regressions can be more accurately bisected to either the different
watermark value (in this patch) or the new DDB allocation (in the next
patch).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211173107.11068-1-matthew.d.roper@intel.com
Try to be more consistent about intel_* types rather than drm_* types
for lower-level driver functions.
v2:
- Also drop the intel_crtc parameter from compute_intermediate_wm()
since we can just extract it from the crtc_state parameter. (Ville)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181210215415.19854-1-matthew.d.roper@intel.com
SKL+ do not use crtc_state->update_wm_pre, so there is absolutely no
point it setting it. crtc_state->update_wm_pre only exists as a
temporary hack for pre-g4x platforms until we redo their
watermarks to be be atomic.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113172330.26069-3-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
skl_compute_wm() wants to compare the old and new watermarks. Currently
it gets at the old watermarks via crtc->state, which is confusing since
it can point at either the old or the new state depending on where
in the sequence we are. In this case it is correct since we have not yet
swapped the states, but let's make it super clear what this is doing
by using the explicit old state.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113172330.26069-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
A variable whose name is 'plane_id' is expected to be of the
enum plane_id type. In this case we have a raw int, which turns
out to refer to the plane of the framebuffer. Rename the variable
to 'color_plane' in line with the trend started earlier.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-13-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
On SKL+ the plane WM/BUF_CFG registers are a proper part of each
plane's register set. That means accessing them will cancel any
pending plane update, and we would need a PLANE_SURF register write
to arm the wm/ddb change as well.
To avoid all the problems with that let's just move the wm/ddb
programming into the plane update/disable hooks. Now all plane
registers get written in one (hopefully atomic) operation.
To make that feasible we'll move the plane ddb tracking into
the crtc state. Watermarks were already tracked there.
v2: Rebase due to input CSC
v3: Split out a bunch of junk (Matt)
v4: Add skl_wm_add_affected_planes() to deal with
cursor special case and non-zero wm register reset value
v5: Drop the unrelated for_each_intel_plane_mask() fix (Matt)
Remove the redundant ddb memset() (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v3
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165900.31298-1-ville.syrjala@linux.intel.com
Simplify the calling convention of the skl+ watermark functions
by not passing around dev_priv needlessly. The callees have
what they need to dig it out anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-10-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Make a cleaner split between the skl+ and icl+ ways of computing
watermarks. This way skl_build_pipe_wm() doesn't have to know any
of the gritty details of icl+ master/slave planes.
We can also simplify a bunch of the lower level code by pulling
the plane visibility checks a bit higher up.
v2: WARN_ON(!visible) for the icl+ master plane case (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165726.31122-1-ville.syrjala@linux.intel.com
We have to pass both level 0 watermark struct and the transition
watermark struct to skl_compute_transition_wm(). Make life less
confusing by just passing the entire plane watermark struct that
contains both aforementioned structures.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-8-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We memset(0) the entire watermark struct the start, so there's no
need to clear things later on.
v2: Rebase due to some stale w/a removal
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-7-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
If the level 0 latency is 0 we can't do anything. Return an error
rather than success.
While this can't happen due to WaWmMemoryReadLatency, it can
happen if the user clears out the level 0 latency via debugfs.
v2: Clarify how how we can end here with zero level 0 latency (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-6-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
I have a Thinkpad X220 Tablet in my hands that is losing vblank
interrupts whenever LP3 watermarks are used.
If I nudge the latency value written to the WM3 register just
by one in either direction the problem disappears. That to me
suggests that the punit will not enter the corrsponding
powersave mode (MPLL shutdown IIRC) unless the latency value
in the register matches exactly what we read from SSKPD. Ie.
it's not really a latency value but rather just a cookie
by which the punit can identify the desired power saving state.
On HSW/BDW this was changed such that we actually just write
the WM level number into those bits, which makes much more
sense given the observed behaviour.
We could try to handle this by disallowing LP3 watermarks
only when vblank interrupts are enabled but we'd first have
to prove that only vblank interrupts are affected, which
seems unlikely. Also we can't grab the wm mutex from the
vblank enable/disable hooks because those are called with
various spinlocks held. Thus we'd have to redesigne the
watermark locking. So to play it safe and keep the code
simple we simply disable LP3 watermarks on all SNB machines.
To do that we simply zero out the latency values for
watermark level 3, and we adjust the watermark computation
to check for that. The behaviour now matches that of the
g4x/vlv/skl wm code in the presence of a zeroed latency
value.
v2: s/USHRT_MAX/U32_MAX/ for consistency with the types (Chris)
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101269
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103713
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114173440.6730-1-ville.syrjala@linux.intel.com
No point in cluttering the common codepaths with the
skip_intermediate_wm handling. Just move it into
ilk_compute_intermediate_wm() as those are the only
platforms using this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108151013.24064-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
Make skl_ddb_allocation_overlaps() useful for other callers
besides skl_update_crtcs(). We'll need it to do plane updates
as well.
And while we're here we can reduce the stack utilization a
bit by noting that each struct skl_ddb_entry is 4 bytes whereas
a pointer to one is 8 bytes (on 64bit). So we'll switch to an
array of structs from the array of pointers we used before.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101150605.18235-9-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Although FBC helps save power it do not belongs to power management
also the cleanup was placed in i915_driver_unload() also not a good
place. intel_modeset_init()/intel_modeset_cleanup() are better places
also this will help make easy disable features that depends in
display being enabled in driver.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108001647.11276-2-jose.souza@intel.com
Gen11 Display suports 32 planes in total. Enable the new format in context
status to be used and expanded to 32 planes.
V2: Move the WA to display WA's(Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030084504.21537-1-radhakrishna.sripada@intel.com
According to BSpec this is not needed anymore:
"This workaround is no longer needed since NV12
support is dropped for the affected projects.
"
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031162845.12419-2-rodrigo.vivi@intel.com
The specially case for SKL for not controlled sagv
is already taken care inside intel_enable_sagv, so there's
no need to duplicate the check here.
v2: Go one step further and remove skl special case. (Jani)
v3: Separate runtime status handle from has_sagv flag.
v4: Go back and accept simple Jani proposed solution.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026200317.21726-1-rodrigo.vivi@intel.com
The 16Gb DIMM w/a is not applicable to BXT or GLK. Limit it to
the appropriate platforms.
This was especially harsh on GLK since we don't even try to read
the DIMM information on that platforms, hence valid_dimm was
always false and thus we always tried to apply the w/a.
Furthermore the w/a pushed the level 0 latency above the
level 1 latency, which doesn't really make sense.
v2: Do the check when populating is_16gb_dimm (Mahesh)
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 86b592876c ("drm/i915: Implement 16GB dimm wa for latency level-0")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023182102.31549-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.sh.kumar@gmail.com>
Skylake style watermarks program the UV parameters into wm->uv_wm,
and have a separate DDB allocation for UV blocks into the same plane.
Gen11 watermarks have a separate plane for Y and UV, with separate
mechanisms. The simplest way to make it work is to keep the current
way of programming watermarks and calculate the Y and UV plane
watermarks from the master plane.
Changes since v1:
- Constify crtc_state where possible.
- Make separate paths for planar formats in skl_build_pipe_wm() (Matt)
- Make separate paths for calculating total data rate. (Matt)
- Make sure UV watermarks are unused on gen11+ by adding a WARN. (Matt)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018115134.9061-5-maarten.lankhorst@linux.intel.com
To make NV12 working on icl, we need to update 2 planes simultaneously.
I've chosen to do this in the CRTC step after plane validation is done,
so we know what planes are (in)visible. The linked Y plane will get
updated in intel_plane_update_planes_on_crtc(), by the call to
update_slave, which gets the master's plane_state as argument.
The link requires both planes for atomic_update to work,
so make sure skl_ddb_add_affected_planes() adds both states.
Changes since v1:
- Introduce icl_is_nv12_y_plane(), instead of hardcoding sprite numbers.
- Put all the state updating login in intel_plane_atomic_check_with_state().
- Clean up changes in intel_plane_atomic_check().
Changes since v2:
- Fix intel_atomic_get_old_plane_state() to actually return old state.
- Move visibility changes to preparation patch.
- Only try to find a Y plane on gen11, earlier platforms only require
a single plane.
Changes since v3:
- Fix checkpatch warning about to_intel_crtc() usage.
- Add affected planes from icl_add_linked_planes() before check_planes(),
it's a cleaner way to do this. (Ville)
Changes since v4:
- Clear plane links in icl_check_nv12_planes() for clarity.
- Only pass crtc_state to icl_check_nv12_planes().
- Use for_each_new_intel_plane_in_state() in icl_check_nv12_planes.
- Rename aux to linked. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022135152.15324-1-maarten.lankhorst@linux.intel.com
[mlankhorst: Change bool slave to u32, to satisfy checkpatch]
[mlankhorst: Add WARN_ON's based on Ville's suggestion]
This message is currently marked as DRM_DEBUG_ATOMIC. I would like it
to be DRM_DEBUG_KMS since it is more KMS than atomic, and this will
also make the message appear in the CI logs, which may or may not help
us with some FIFO underrun bugs.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004231600.14101-7-paulo.r.zanoni@intel.com
We were writing to PLANE_BUF_CFG(pipe, plane_id) twice for every
platform, and we were even using different values on the gen10- planar
case. The first write is useless since it just gets replaced with the
next one, so kill it.
There's a lot to improve in the DDB code, but let's start by avoiding
the double write.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004231600.14101-6-paulo.r.zanoni@intel.com
The transition watermarks ask for Selected Result Blocks (the real
value), not Result Blocks (the integer value). Given how ceilings are
applied in both the non-transition and the transition watermarks
calculations, we can get away with assuming that Selected Result
Blocks is actually Result Blocks minus 1 without any rounding errors.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004231600.14101-5-paulo.r.zanoni@intel.com
The transition minimum is 14 blocks for gens 9 and 10, and 4 blocks
for gen 11. This minimum value is supposed to be added to the
configurable trans_amount. This matches both BSpec and additional
information provided by our HW engineers.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004231600.14101-3-paulo.r.zanoni@intel.com
symmetric_memory do not change after initialization so lets just set
ipc_enabled once for this WA.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180918204714.27306-5-jose.souza@intel.com
SKL has IPC but it should not be set according to the WA, so lets
just mark as it don't have it to simply the code and avoid
unnecessary MMIO writes at every call to intel_enable_ipc().
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180918204714.27306-4-jose.souza@intel.com
IPC was only added in SKL+(actually we don't even enable for SKL due
WA) so without this change, driver was writing to a reserved bit.
Also removing the uncessary dev_priv->ipc_enabled = false; as now
gens without IPC will not have IPC enabled.
v2(Rodrigo):
- moved the new handling of WA #0477 to the next patch
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180918204714.27306-3-jose.souza@intel.com
IPC may cause underflows if not used with dual channel symmetric
memory configuration. Disable IPC for non symmetric configurations in
affected platforms.
Display WA #1141
Changes Since V1:
- Re-arrange the code.
- update wrapper to return if memory is symmetric (Rodrigo)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824093225.12598-6-mahesh1.kumar@intel.com
Memory with 16GB dimms require an increase of 1us in level-0 latency.
This patch implements the same.
Bspec: 4381
changes since V1:
- s/memdev_info/dram_info
- make skl_is_16gb_dimm pure function
Changes since V2:
- make is_16gb_dimm more generic
- rebase
Changes since V3:
- Simplify condition (Maarten)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180831110942.9234-1-mahesh1.kumar@intel.com
If we cannot setup rc6, we cannot let the GPU suspend itself as it
cannot save its state (to a powercontext). As such, we must disable
runtime-pm, but we should do so using the low-level pm-runtime function
which leaves our own debugging functions intact (and continue to detect
errors in our runtime-pm handling should we ever be able to enable rc6).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180812223642.24865-3-chris@chris-wilson.co.uk
We distribute DDB equally among all pipes irrespective of display
buffer requirement of each pipe. This leads to a situation where high
resolution y-tiled display can not be enabled with 2 low resolution
displays.
Main contributing factor for DDB requirement is width of the display.
This patch make changes to distribute ddb based on display width.
So display with higher width will get bigger chunk of DDB.
Changes Since V1:
- pipe_size/ddb_size will not overflow u16 so use appropriate
data-types during computation (Chris)
Changes Since V2:
- avoid redundancy and possible truncation errors (Chris)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107113
Cc: raviraj.p.sitaram@intel.com
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180801151113.5337-1-mahesh1.kumar@intel.com
ddb_size is u16 so use same return type for intel_get_ddb_size
wrapper.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731142445.30723-2-mahesh1.kumar@intel.com
We don't have proper watermark NV12 support on ICL due to differences
in how it should be implemented. In commit 234059da0f
("drm/i915/icl: NV12 y-plane ddb is not in same plane") we avoided
writing the non-existent PLANE_NV12_BUF_CFG registers but we forgot to
also avoid them on the hardware state readout. While the code is still
not correct, at least now we can avoid unclaimed register error
messages when dealing with RGB formats, which makes CI happier.
Also add some FIXME comments in order to make it even more clear that
there's still work to do.
References: commit 234059da0f ("drm/i915/icl: NV12 y-plane ddb is
not in same plane")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180801004614.22149-1-paulo.r.zanoni@intel.com
We used to reset last_adj to 0 on crossing a power domain boundary, to
slow down our rate of change. However, commit 60548c554b ("drm/i915:
Interactive RPS mode") accidentally caused it to be reset on every
frequency update, nerfing the fast response granted by the slow start
algorithm.
Fixes: 60548c554b ("drm/i915: Interactive RPS mode")
Testcase: igt/pm_rps/mix-max-config-loaded
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802100631.31305-1-chris@chris-wilson.co.uk
RPS provides a feedback loop where we use the load during the previous
evaluation interval to decide whether to up or down clock the GPU
frequency. Our responsiveness is split into 3 regimes, a high and low
plateau with the intent to keep the gpu clocked high to cover occasional
stalls under high load, and low despite occasional glitches under steady
low load, and inbetween. However, we run into situations like kodi where
we want to stay at low power (video decoding is done efficiently
inside the fixed function HW and doesn't need high clocks even for high
bitrate streams), but just occasionally the pipeline is more complex
than a video decode and we need a smidgen of extra GPU power to present
on time. In the high power regime, we sample at sub frame intervals with
a bias to upclocking, and conversely at low power we sample over a few
frames worth to provide what we consider to be the right levels of
responsiveness respectively. At low power, we more or less expect to be
kicked out to high power at the start of a busy sequence by waitboosting.
Prior to commit e9af4ea2b9 ("drm/i915: Avoid waitboosting on the active
request") whenever we missed the frame or stalled, we would immediate go
full throttle and upclock the GPU to max. But in commit e9af4ea2b9, we
relaxed the waitboosting to only apply if the pipeline was deep to avoid
over-committing resources for a near miss. Sadly though, a near miss is
still a miss, and perceptible as jitter in the frame delivery.
To try and prevent the near miss before having to resort to boosting
after the fact, we use the pageflip queue as an indication that we are
in an "interactive" regime and so should sample the load more frequently
to provide power before the frame misses it vblank. This will make us
more favorable to providing a small power increase (one or two bins) as
required rather than going all the way to maximum and then having to
work back down again. (We still keep the waitboosting mechanism around
just in case a dramatic change in system load requires urgent uplocking,
faster than we can provide in a few evaluation intervals.)
v2: Reduce rps_set_interactive to a boolean parameter to avoid the
confusion of what if they wanted a new power mode after pinning to a
different mode (which to choose?)
v3: Only reprogram RPS while the GT is awake, it will be set when we
wake the GT, and while off warns about being used outside of rpm.
v4: Fix deferred application of interactive mode
v5: s/state/interactive/
v6: Group the mutex with its principle in a substruct
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107111
Fixes: e9af4ea2b9 ("drm/i915: Avoid waitboosting on the active request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731132629.3381-1-chris@chris-wilson.co.uk
According to intel_read_wm_latency() it is perfectly legal for one WM
and all subsequent levels to be 0 (and the deeper powersaving states
disabled), so don't shout *ERROR*, over and over again.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180726161527.10516-1-chris@chris-wilson.co.uk
While things may have been different before, right now the function is
very simple and has a single caller. IMHO any possible benefits from
an abstraction here are gone and not worth the price of the current
indirection while reading the code.
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607230700.28359-1-paulo.r.zanoni@intel.com
