Convert the legacy system PM callbacks to new ones. Meanwhile, remove the
redudant calls to the PCI for changing a power state since it's done by bus
code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current kernel, the CONFIG_PPC_OF is always 'y' for the ppc
arch. So we don't need to check it with other ppc specific options.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.
Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As more ARM platforms are moving into ARCH_MULTIPLATFORM, we can now
have integrator and versatile in the same kernel, and first one selects
this driver, causing a Kconfig warning:
warning: (ARCH_INTEGRATOR_AP) selects SERIAL_AMBA_PL010 which has unmet direct dependencies (TTY && HAS_IOMEM && ARM_AMBA && (BROKEN || !ARCH_VERSATILE))
It turns out that it has not been broken on versatile for a long time,
so we can remove the statement here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
UARTs which do not trigger THRE interrupt if the fifo is already
empty when the interrupt is enabled need tx primed manually. These
UARTs are identified by the UART_BUG_TXEN flag to enable the
required workaround.
However, the current workaround is broken; if the fifo is already
empty but the shifter is still transmitting, then serial8250_tx_chars()
will not be called but no further THRE interrupt will occur, and
tx will stall. The appropriate check is for fifo empty (THRE), not
transmitter empty (TEMT).
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
[pjh: rewrote commit log]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the last missing piece to get a kernel booting to a prompt in qemu-cris.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The general agreed way to specify a fixed line number
for a serial console is to provide a "serial" alias
in the devicetree. Start parsing this property in
of_serial.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EarlyCon support depends on serial console infrastructure, so the code
implementing it should depend on CONFIG_SERIAL_SAMSUNG_CONSOLE.
This patch fixes the following build break:
CC [M] drivers/tty/serial/samsung.o
drivers/tty/serial/samsung.c:2468:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2468:1: error: expected declaration specifiers or ‘...’ before ‘s3c2410_setup_earlycon’
drivers/tty/serial/samsung.c:2487:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2487:1: error: expected declaration specifiers or ‘...’ before ‘s3c2412_setup_earlycon’
drivers/tty/serial/samsung.c:2488:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2488:1: error: expected declaration specifiers or ‘...’ before ‘s3c2440_setup_earlycon’
drivers/tty/serial/samsung.c:2489:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2489:1: error: expected declaration specifiers or ‘...’ before ‘s3c6400_setup_earlycon’
drivers/tty/serial/samsung.c:2506:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2506:1: error: expected declaration specifiers or ‘...’ before ‘s5pv210_setup_earlycon’
drivers/tty/serial/samsung.c:2507:1: error: expected declaration specifiers or ‘...’ before string constant
drivers/tty/serial/samsung.c:2507:1: error: expected declaration specifiers or ‘...’ before ‘exynos4210_setup_earlycon’
drivers/tty/serial/samsung.c:2468:1: warning: ‘s3c2410_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2487:1: warning: ‘s3c2412_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2488:1: warning: ‘s3c2440_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2489:1: warning: ‘s3c6400_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2506:1: warning: ‘s5pv210_setup_earlycon’ defined but not used [-Wunused-function]
drivers/tty/serial/samsung.c:2507:1: warning: ‘exynos4210_setup_earlycon’ defined but not used [-Wunused-function]
make[3]: *** [drivers/tty/serial/samsung.o] Error 1
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/8250/8250_core.c:2503:6: sparse: symbol 'serial8250_set_divisor' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a full sc9836-uart driver for SC9836 SoC which is based on the
spreadtrum sharkl64 platform.
This driver also support earlycon.
Originally-by: Lanqing Liu <lanqing.liu@spreadtrum.com>
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function s3c24xx_serial_start_tx_pio() enables interrupts if needed,
so we don't have to (or even we shouldn't) enable them before.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP UART ignores MCR[1] (ie., RTS) when in autoRTS mode. This
makes it impossible for either the serial core or userspace to
manually flow control the sender.
Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 88838d3112702 ("serial: omap_8250: Fix RTS handling") fixed
RTS pin control when in autoRTS mode.
New support added in "serial: core: Rework hw-assisted flow control support"
enables a much simpler approach; rather than masking out autoRTS
whenever writing the EFR register, use the UPSTAT_* mode to determine if
autoRTS should be enabled when raising RTS (in omap8250_set_mctrl()).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw-assisted flow control support was added to the serial core
in v3.8 with commits,
dba05832cb ("SERIAL: core: add hardware assisted h/w flow control support")
2cbacafd7a ("SERIAL: core: add hardware assisted s/w flow control support")
9aba8d5b01 ("SERIAL: core: add throttle/unthrottle callbacks for hardware
assisted flow control")
Since then, additional requirements for serial core support have arisen.
Specifically,
1. Separate tx and rx flow control settings for UARTs which only support
tx flow control (ie., autoCTS).
2. Disable sw-assisted CTS flow control in autoCTS mode
3. Support for RTS flow control by serial core and userspace in autoRTS mode
Distinguish mode from capability; introduce UPSTAT_AUTORTS, UPSTAT_AUTOCTS
and UPSTAT_AUTOXOFF which, when set by the uart driver, enable serial core
support for hw-assisted rx, hw-assisted tx and hw-assisted in-band/IXOFF
rx flow control, respectively. [Note: hw-assisted in-band/IXON tx flow
control does not require serial core support/intervention and can be
enabled by the uart driver when required.]
These modes must be set/reset in the driver's set_termios() method, based
on termios settings, and thus can be safely queried in any context in which
one of the port lock, port mutex or termios rwsem are held. Set these modes
in the 2 in-tree drivers, omap-serial and 8250_omap, which currently
use UPF_HARD_FLOW/UPF_SOFT_FLOW support.
Retain UPF_HARD_FLOW and UPF_SOFT_FLOW as capabilities; re-define
UPF_HARD_FLOW as both UPF_AUTO_RTS and UPF_AUTO_CTS to allow for distinct
and separate rx and tx flow control capabilities.
Disable sw-assisted CTS flow control when UPSTAT_AUTOCTS is enabled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PXA variant of the 8250 UART adds a UART enable bit which must not
be cleared. Make the earlycon support maintain this bit if it is set.
This implies some initialization of the UART, but we cannot
unconditionally set the bit as some other variants require this bit to
be clear for other functions.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add mrvl,pxa-uart and mrvl,mmp-uart compatible strings for the of_serial
driver. These are 8250 variants which have a port type of PORT_XSCALE.
There is also the serial driver pxa.c with these compatible strings
already. However, it can be replaced with the common 8250 driver. It has
some issues like it cannot coexist with the 8250 driver due to tty name
collision. That also means adding these compatible strings here should
not case a problem.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for alias parsing from the DT. This allows for consistent
tty numbering.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port shadow registers, ->fcr and ->mcr, must be protected from
concurrent updates. Relocate the shadow register updates in
serial8250_do_set_termios() to the port lock critical section.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using no_console_suspend, the serial console may be powered off
anyway during system sleep. Upon resume, the port may be in its default
power-on state, but is expected to continue console i/o before the device
has received its pm callback. The resultant garbage i/o can cause all
kinds of havoc on the remote end.
Use the scratch register as a canary to discover if the console
has been powered-off. Write a non-zero value to the scratch register
at port suspend and reprogram the port before any console i/o if the
scratch register != canary before port resume.
This workaround is disabled for omap_8250 (which uses different divisor
programming).
Credit to Doug Anderson <dianders@chromium.org> for the idea of using
the scratch register canary to discover port power-down.
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exar XR17V35X PCIe uarts support a 4-bit fractional divisor register.
Refactor the divisor calculation from the divisor programming.
Allow a fractional result from serial8250_get_divisor() and pass this
result to serial8250_dl_write().
Simplify the calculation for quot and quot_frac. This was verified
to be identical to the results of the original calculation with a test
jig.
NB: The results were also compared with the divisor value chart
on pg 33 of the Exar XR17V352 datasheet, rev 1.0.3, here:
http://www.exar.com/common/content/document.ashx?id=1585
which differs from the calculated values by 1 in the fractional result.
This is because the calculated values are still rounded in the
fractional result, whereas the table values are truncated. Note
that the data error rate % values in the datasheet are for
rounded fractional results, as the truncated fractional results
have more error.
Cc: Joe Schultz <jschultz@xes-inc.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor divisor register programming into a new function,
serial8250_set_divisor; this allows serial console to reinitialize
early after resume from suspend.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the computation of the LCR register value from termios c_cflag
into a new local function, serial8250_compute_lcr().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART_BUG_QUOT workaround adjusts the divisor computed from the
baud rate by serial8250_get_divisor(). Move the workaround into
serial8250_get_divisor(), so that divisor-from-baud computation
is encapsulated.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
16z135 IP Core has changed so the driver needs to be updated to respect
these changes. The following changes have been made:
* Don't invert the 16z135 modem status register when reading.
* Add module parameter to configure the (baud rate dependent) RX timeout.
Character timeout in seconds = (timeout_reg * baud_reg * 4)/freq_reg.
* Enable the handling of UART core's automatic flow control feature.
When AFE is active disable generation of modem status IRQs.
* Rework the handling of IRQs to be conform with newer FPGA versions and
take precautions not to miss an interrupt because of the destructive read
of the IIR register.
* Correct men_z135_handle_modem_status(), MSR is stat_reg[15:8] not
stat_reg[7:0]
* Correct calling of uart_handle_{dcd,cts}_change()
* Reset CLOCAL when CRTSCTS is set
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the uart port being suspended is a console and consoles are
not suspending (kernel command line contains no_console_suspend),
then no action is performed for that port, and the function can
return early.
If the function has not returned early, then one of the conditions
is not true, so the expression
(console_suspend_enabled || !uart_console(uport))
must be true and can be eliminated.
Similarly, the expression
(console_suspend_enabled && uart_console(uport))
simplifies to just uart_console(uport).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for early console initialized from device tree
and kernel command line to all variants of Samsung serial driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
[mszyprow: added support for command line based initialization,
fixed comments, added documentation]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the driver cannot return from overrun error if characters
are output during overrun process, use dev_dbg() instead of
dev_notice() to log the error message of overrun in syslog.
Based on a patch by Hisashi Nakamura.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we would like to send amount of data less than FIFO size we better would do
this via PIO mode. Otherwise the overhead could be significant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we return in the first branch the second one doesn't require an
additional else keyword. The patch removes it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make it possible to restore from hibernation not only in Linux but
also in e.g. U-Boot, we have to use sci_{suspend|remove}() for the PM {freeze|
thaw|restore}() methods. It's handy to achieve this by using SIMPLE_DEV_PM_OPS()
macro, however we have to annotate sci_{suspend|remove}() with '__maybe_unused'
in order to avoid compilation warnings when CONFIG_PM_SLEEP is undefined.
Based on orignal patch by Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The implementation of flushing the RX FIFO breaks in a number of cases,
it is impossible to ensure an complete flush of the RX FIFO due to the
hardware not allowing the use of the FIFOs when the receiver is disabled
(Reading from the FIFO register does not remove it from the FIFO when
the RX_EN=0 or RX_DIS=1). Additionally during an initial set_termios
call where RX_DIS=1 causes a hang waiting forever for the RX FIFO to
empty. On top of this the FIFO will be cleared by the use of the RXRST
bits on the Control Register, making the RX flush pointless (as it does
not preserve the data read anyway).
Due to the TXRST the TX FIFO and transmitter can be interrupted during
frame trasmission, causing corruption and additionally data lost in the
FIFO. Most other serial drivers do not flush or clear the FIFOs during
a termios configuration change and as such do not have issues with
corruption. For this UART controller is it required that the TXRST/RXRST
bit be flagged during the change, this means that the data in the FIFO
will be dropped when changing configuration. In order to prevent data
loss and corruption of the transmitted data, wait until the TX FIFO is
empty before changing the configuration. The performance of this may
cause the set_termios call to take a longer amount of time especially
on lower baud rates, however it is comparable to the same performance
hit that a console_write call costs.
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Acked-by: Anirudha Sarangi <anirudh@xilinx.com>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to explicitly zero the 'ret' variable as it is properly
initialized in a few lines below as:
ret = serial_mxs_probe_dt(s, pdev);
Remove the unneeded zeroing of 'ret'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should check whether platform_get_irq() failed, and in the case of error
this needs to be propagated.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The irq number is only used inside the probe function, so there is no need
to keep it in the private mxs_auart_port structure.
Use a local 'irq' variable for storing the irq number instead.
Also make its type of 'int' as platform_get_irq() may fail and return a
negative number.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Digicolor USART hardware does not support detecting the BREAK condition.
This means that we can't support sysrq on this hardware. Remove all reference
to sysrq from the code.
This also fixes build when sysrq is disabled:
drivers/tty/serial/digicolor-usart.c: In function 'digicolor_uart_console_write':
drivers/tty/serial/digicolor-usart.c:407:33: error: 'struct uart_port' has no member named 'sysrq'
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the kernel command line parameter, no_console_suspend, is used,
the console should continue to output console messages during and
after system suspend. For a serial console, the serial core ensures
that the device is not shutdown when no_console_suspend is specified.
However, the default operation of the pnp bus will disable and suspend
the device and no further output occurs.
When registering the 8250 port, if the serial device is a console
set the PNP_CONSOLE capability, which prevents device power-off
if consoles are not suspending.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unregister_console() will be called from uart_remove_one_port() while
removing the platform driver. So not necessary to call it in driver
exit path.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change does following:
- baud, flow, bits, parity were being overwritten as they were
being reinitialized after parsing. Initialize them when they are
declared so that user provided setting are not overwritten.
- msm_set_baud_rate() is anyway called in uart_set_options when it calls
msm_set_termios(). msm_reset() is called when we change the baud rate.
Hence doing away with both of these calls.
- CR_CMD_PROTECTION_EN and CR_TX_ENABLE settings are done in msm_set_baud_rate.
So do away with this here.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Moorestown platform support was removed few years ago. This is a follow
up which removes Moorestown specific code for the serial devices. It includes
mrst_max3110 and earlyprintk bits.
This was used on SFI (Medfield, Clovertrail) based platforms as well, though
new ones use normal serial interface for the console service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running an userspace program that does a 'tcflush(fd, TCIOFLUSH)' call
we still see the last received character in the URXD register afterwards.
Clear UCR2_SRST bit so that the UART FIFO is flushed properly.
Since UCR2_SRST also resets some UART registers, we need to save and restore
some of them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fugang Duan <B38611@freescale.com>
Acked-by: Jason Liu <r64343@freecale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On uart buffer flush, serial core resets the circular buffer.
If a DMA transfer is in progress at that time, the callback
lpuart_dma_tx_complete will move buffer's tail unconditionally,
hence tail moves beyond head. Use the flush_buffer hook to
terminate the DMA imeaditely and avoid lpuart_dma_tx_complete
being called in this situation.
This bug often showed up while shutdown and lead to duplicate
serial console output.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For power management support, we should disable TX and
TX interrupt so that kernel can prepare for deep sleep.
Retain RX and RX interrupt for wakeup the kernel when
receive the input character.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To end a DMA transfer which did not consume a whole buffer (e.g. one
character only), a RX timer is used. When lots of data are received
the DMA transfer will complete and setup another DMA transfer, which
in turn might complete again. In this cases, it is not necessary to
abort the DMA transfers using the RX timer. This change pushes the
RX timer timeout into the future each time a DMA transfer completed.
Aborting the DMA was not very harmful, since the next received
character lead to setup of another RX DMA.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the DMA channel request to probe to avoid requesting the DMA
channel on each opening of the ttyLPx device. This also fixes a
potential issue that TX channel is not freed when only RX channel
allocation fails. The DMA channels are now handled independently,
so one could use UART with DMA only in TX direction for instance.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the UART is in DMA receive mode (RDMAS set) and one character
just arrived while another interrupt is handled (e.g. TX), the RDRF
(receiver data register full flag) is set due to the water level of
1. But since the DMA will take care of this character, there is no
need to handle it by calling lpuart_prepare_rx. Handling it leads to
adding the RX timeout timer twice:
[ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
[ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
[ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
[ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
[ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
[ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
[ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
[ 74.373960] LR is at lpuart_int+0x15c/0x3d8
[ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
[ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
[ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
[ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
[ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
[ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
[ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
...
Solve this by only execute the receiver path (lpuart_prepare_rx) if
the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
cleared on initialization, in case it has been left set.
This can be best reproduced using UART as a serial console, then
running top while dd'ing data into the terminal.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial port gets closed while a RX transfer is in progress,
the timer might fire after the serial port shutdown finished. This
leads in a NULL pointer dereference:
[ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 7.516590] pgd = 86348000
[ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
[ 7.526145] Internal error: Oops: 17 [#1] ARM
[ 7.530611] Modules linked in:
[ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
[ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
[ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
[ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
[ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
[ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
[ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
[ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
[ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
[ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
[ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
[ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
Setup the timer on UART startup which allows to delete the timer
unconditionally on shutdown. This also saves the initialization
on each transfer.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
