Make sure the option card does not respond after shutdown by disabling
it via ESIC's Expansion Board Control register. Also disable memory and
port I/O decoders, the latter in particular to disable slot-specific I/O
decoding that otherwise remains active even in the board is disabled.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ESIC's memory area 1 (MEMCS1) and its Memory Address High Compare
and Memory Address Low Compare registers to set up the MMIO range for
decoding accesses to PDQ ASIC registers. Previously the PDQ ASIC was
thought to be addressable with the memory area 0 (MEMCS0) and its Memory
Address Compare and Memory Address Mask registers.
The MMIO range allocated for the option card is preset via ECU (EISA
Configuration Utility) and can be disabled, so handle such a case
gracefully too.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correctly propagate the error code from `pci_enable_device' if non zero.
Currently a failure of this function is correctly recognized and device
initialization abandoned, however a successful completion code returned.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a6111d3c "vlan: Pass SIOC[SG]HWTSTAMP ioctls to real device"
intended to enable hardware time stamping on VLAN interfaces, but
passing SIOCSHWTSTAMP is only half of the story. This patch adds
the second half, by letting user space find out the time stamping
capabilities of the device backing a VLAN interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-11-20
This series contains updates to ixgbevf, i40e and i40evf.
Emil updates ixgbevf with much of the work that Alex Duyck did while at
Intel. First updates the driver to clear the status bits on allocation
instead of in the cleanup routine, this way we can leave the recieve
descriptor rings as a read only memory block until we actually have
buffers to give back to the hardware. Clean up ixgbevf_clean_rx_irq()
by creating ixgbevf_process_skb_field() to merge several similar
operations into this new function. Cleanup temporary variables within
the receive hot-path and reducing the scope of variables that do not
need to exist outside the main loop. Save on stack space by just
storing our updated values back in next_to_clean instead of using
a stack variable, which also collapses the size the function. Improve
performace on IOMMU enabled systems and reduce cache misses by changing
the basic receive patch for ixgbevf so that instead of receiving the
data into an skb, it is received into a double buffered page. Add
netpoll support by creating ixgbevf_netpoll(), which is a callback for
.ndo_poll_controller to allow for the VF interface to be used with
netconsole.
Mitch provides several cleanups and trivial fixes for i40e and i40evf.
First is a fix the overloading of the msg_size field in the
arq_event_info struct by splitting the field into two and renaming to
indicate the actual function of each field. Updates code comments
to match the actual function. Cleanup several checkpatch.pl warnings
by adding or removing blank lines, aligning function parameters, and
correcting over-long lines (which makes the code more readable).
Shannon provides a patch for i40e to write the extra bits that will
turn off the ITR wait for the interrupt, since we want the SW INT to
go off as soon as possible.
v2: updated patch 07 based on feedback from Alex Duyck by
- adding pfmemalloc check to a new function for reusable page
- moved atomic_inc outside of #if/else in ixgbevf_add_rx_frag()
- reverted the removal of the API check in ixgbevf_change_mtu()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver updates 2014-11-20
The following series of patches includes functional updates to the
driver as well as some trivial changes.
- Add a read memory barrier in the Tx and Rx path after checking the
descriptor ownership bit
- Wait for the Tx engine to stop/suspend before issuing a stop command
- Implement a smatch tool suggestion to simplify an if statement
- Separate out Tx and Rx ring data fields into their own structures
- Add BQL support
- Remove an unused variable
- Change Tx coalescing support to operate on packet basis instead of
a descriptor basis
- Add support for the skb->xmit_more flag
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to delay telling the hardware about data that is ready to
be transmitted if the skb->xmit_more flag is set.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current form of Tx coalescing works on a descriptor basis instead
of on a packet basis and doesn't take into account TSO packets. Update
the Tx coalescing support to work on a packet basis, taking into
account the number of packets associated with a TSO transmit. Also,
only activate the Tx timer if a timer value is set.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tso_header variable in the xgbe_tx_ring_data structure is not used,
remove it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call the appropriate BQL functions to track the number of bytes queued
during Tx processing and to track the number of packets and bytes
that have been transmitted during Tx complete processing.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Tx and Rx related fields within the xgbe_ring_data struct into
their own structs in order to more easily see what fields are used for
each operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Smatch tool indicated that one of the if statements in xgbe-dev.c
could be rewritten to remove a redundant check for the 'err' variable
in an if statement.
Change the statement as suggested and add a comment to help clarify.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the Tx engine is told to stop while it is actively processing Tx
descriptors it is possible that the Tx descriptor(s) will not be closed
out properly. When the Tx engine is restarted this could result in the
driver being stuck on the improperly closed descriptor.
Update the driver to wait for the Tx engine to be in a stopped or
suspended state before issuing the stop command.
This has not been an issue to date, but it's a good safe-guard to have.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a read memory barrier to the Tx and Rx paths where the ownership
bit is checked to be sure that all descriptor fields are read after
having read the ownership bit for the descriptor.
This has not been an issue to date, but it's a good safe-guard to have.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions kfree() and of_node_put() test whether their argument is NULL
and then return immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ethtool set settings to not check AUTONEG_ENABLE
mlx4_en_set_settings should not check if cmd->autoneg == AUTONEG_ENABLE,
cmd->autoneg can be enabled by default and this check will fail other settings requests.
mlx4_en driver doesn't support changing autoneg value, but shouldn't fail the request
in case cmd->autoneg was set.
Fixes: d48b3ab ("net/mlx4_en: Use PTYS register to set ethtool settings (Speed)")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a pci_dma_mapping_error() call to check for mapping errors before
further using the dma handle. In case of error, control goes to a new label
where the incoming skb is freed. Unchecked dma handles were found using
Coccinelle:
@rule1@
expression e1;
identifier x;
@@
*x = pci_map_single(...);
... when != pci_dma_mapping_error(e1,x)
Signed-off-by: Tina Johnson <tinajohnson.1234@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe says:
====================
tipc: new netlink API
v3
The old API is not removed.
The new API is separated from the old because of a bug in the old
tipc-config utility using it. When adding commands to the existing
genl_ops struct the get-family response message grows to a point where
it overflows the small receive buffer in tipc-config, subsequently
breaking the tool. Hence the two genl_family and genl_ops structs.
The new headers are placed in a new file called tipc_netlink.h rather
than added to tipc_config.h as they where in previous versions of this
patchset.
/v3
v2
Redesigned "socket list command" to address David Millers comments in
net-next v1 of this patchset.
Simply put the problem is that we can have an arbitrary amount of
sockets with an arbitrary amount of associated publications. In the
previous patchset this was solved by nesting as many publications as
possible into a socket. If all didn't fit it sent the same socket again
with the remaining publications. As David Miller pointed out this makes
each message malformed as the receiver cannot by the data itself know if
it has received a complete set or not. This was flagged outside of the
data and the client did the reassembly.
o socket 1
o publ 1
o publ 2
o socket 1
o publ 3
o publ 4
In this patchset this is divided into socket listing and publication
listing to avoid having nested data of arbitrary size.
TIPC_NL_SOCK_GET now dumps all sockets with any nested connection
information. However, it no longer include publication information,
only a HAS_PUBL flag to indicate whether the socket has publications or
not. To compliment this there is a new command TIPC_NL_PUBL_GET which
takes a socket as argument and dumps all associated publications.
This means that on "top-level" the data is always complete. In the case
of "tipc socket list" (new tipc-config -p) it first queries all sockets
with TIPC_NL_SOCK_GET and if the socket is published it fetches the
publications using TIPC_NL_PUBL_GET. This is slow for large amount of
sockets with a low publication count (worst case). However, the
integrity is preserved and there is no malformed messages.
/v2
This is a new netlink API for TIPC. It's intended to replace the
existing ASCII API. It utilizes many of the standard netlink
functionalities in the kernel, such as attribute nesting and
input polices.
There are a couple of reasons for this rewrite. The main and most
easily justifiable is that the existing API doesn't scale. Meaning
that a TIPC cluster with a larger amount of nodes, publications or
ports will rapidly exceed what the exiting API can handle. Resulting
in truncated or corrupt responses. In addition to this, the existing
ASCII API rarely uses "standard" kernel functions and has several
tipc specific functions for sanity checking and string formating.
The new API utilizes standard function for pushing data to socket
buffers and netlink attribute nesting to logically group data.
The new API can handle an arbitrary amount of data for things that
are likely to scale up as the TIPC usage and/or cluster size
increases.
A new user-space tool has been developed to work with this new API.
It is called "tipc" and is part of the "tipc-utils" package that
comes with many Linux distributions. The new "tipc" tool utilizes
standard functions from libnl to format, send, receive and process
messages. The tool has borrowed design philosophies from git and the
ip tool. Making the syntax resemble that of ip whiles its strong
modularity resembles that of git.
The existing tool for managing TIPC, "tipc-config" remains in the
package, but when built for kernels that has this new API it is
replaced by a script-based wrapper that maps the old syntax to the
new tool. This way, backwards compatibility is mostly preserved.
MORE ABOUT THE CODE
The main challenge here is to handle the case where the data is of
arbitrary size. This was largely neglected in the old API design.
For example when there is a lot of sockets that has a large amount of
associated publications. In this specific case we can't assume that
all ports nor for that matter all the publications can fit inside a
single netlink message. Sending everything in one batch isn't an
option as we need to yield for the socket layer to cope.
This is solved by using the standard netlink callback for dumping
data and releasing the locks when the netlink message is full. The
dumping mechanism gets us back and we keep a reference (logical) to
where we where when the message became full. This means that we are
not "atomic", what is retrieved by user-space isn't a snapshot at a
certain time but rather a continuously updated data set. In the case
where we can't find our way back i.e. our logical reference are gone
we set a standard flag (NLM_F_DUMP_INTR) to tell user-space that the
dump was interrupted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NAME_TABLE_GET command to the new tipc netlink API.
This command supports dumping the name table of all nodes.
Netlink logical layout of name table response message:
-> name table
-> publication
-> type
-> lower
-> upper
-> scope
-> node
-> ref
-> key
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NET_SET command to the new tipc netlink API.
This command can set the network id and network (tipc) address.
Netlink logical layout of network set message:
-> net
[ -> id ]
[ -> address ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NET_GET command to the new tipc netlink API.
This command dumps the network id of the node.
Netlink logical layout of returned network data:
-> net
-> id
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_NODE_GET to the new tipc netlink API.
This command can dump the address and node status of all nodes in the
tipc cluster.
Netlink logical layout of returned node/address data:
-> node
-> address
-> up flag
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_MEDIA_SET command to the new tipc netlink API.
This command can set one or more link properties for a particular
media.
Netlink logical layout of bearer set message:
-> media
-> name
-> link properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_MEDIA_GET command to the new tipc netlink API.
This command supports dumping all information about all defined
media as well as getting all information about a specific media.
The information about a media includes name and link properties.
Netlink logical layout of media get response message:
-> media
-> name
-> link properties
-> tolerance
-> priority
-> window
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_LINK_RESET_STATS command to the new netlink API.
This command resets the link statistics for a particular link.
Netlink logical layout of link reset message:
-> link
-> name
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_LINK_SET to the new tipc netlink API.
This command can set one or more link properties for a particular
link.
Netlink logical layout of link set message:
-> link
-> name
-> properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_LINK_GET command to the new tipc netlink API.
This command supports dumping all information about all links
(including the broadcast link) or getting all information about a
specific link (not the broadcast link).
The information about a link includes name, transmission info,
properties and link statistics.
As the tipc broadcast link is special we unfortunately have to treat
it specially. It is a deliberate decision not to abstract the
broadcast link on this (API) level.
Netlink logical layout of link response message:
-> port
-> name
-> MTU
-> RX
-> TX
-> up flag
-> active flag
-> properties
-> priority
-> tolerance
-> window
-> statistics
-> rx_info
-> rx_fragments
-> rx_fragmented
-> rx_bundles
-> rx_bundled
-> tx_info
-> tx_fragments
-> tx_fragmented
-> tx_bundles
-> tx_bundled
-> msg_prof_tot
-> msg_len_cnt
-> msg_len_tot
-> msg_len_p0
-> msg_len_p1
-> msg_len_p2
-> msg_len_p3
-> msg_len_p4
-> msg_len_p5
-> msg_len_p6
-> rx_states
-> rx_probes
-> rx_nacks
-> rx_deferred
-> tx_states
-> tx_probes
-> tx_nacks
-> tx_acks
-> retransmitted
-> duplicates
-> link_congs
-> max_queue
-> avg_queue
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_PUBL_GET command to the new tipc netlink API.
This command supports dumping of all publications for a specific
socket.
Netlink logical layout of request message:
-> socket
-> reference
Netlink logical layout of response message:
-> publication
-> type
-> lower
-> upper
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_SOCK_GET command to the new tipc netlink API.
This command supports dumping of all available sockets with their
associated connection or publication(s). It could be extended to reply
with a single socket if the NLM_F_DUMP isn't set.
The information about a socket includes reference, address, connection
information / publication information.
Netlink logical layout of response message:
-> socket
-> reference
-> address
[
-> connection
-> node
-> socket
[
-> connected flag
-> type
-> instance
]
]
[
-> publication flag
]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_BEARER_SET command to the new tipc netlink API.
This command can set one or more link properties for a particular
bearer.
Netlink logical layout of bearer set message:
-> bearer
-> name
-> link properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_NL_BEARER_GET command to the new tipc netlink API.
This command supports dumping all data about all bearers or getting
all information about a specific bearer.
The information about a bearer includes name, link priorities and
domain.
Netlink logical layout of bearer get message:
-> bearer
-> name
Netlink logical layout of returned bearer information:
-> bearer
-> name
-> link properties
-> priority
-> tolerance
-> window
-> domain
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new netlink API for tipc that can disable or enable a tipc bearer.
The new API is separated from the old API because of a bug in the
user space client (tipc-config). The problem is that older versions
of tipc-config has a very low receive limit and adding commands to
the legacy genl_opts struct causes the ctrl_getfamily() response
message to grow, subsequently breaking the tool.
The new API utilizes netlink policies for input validation. Where the
top-level netlink attributes are tipc-logical entities, like bearer.
The top level entities then contain nested attributes. In this case
a name, nested link properties and a domain.
Netlink commands implemented in this patch:
TIPC_NL_BEARER_ENABLE
TIPC_NL_BEARER_DISABLE
Netlink logical layout of bearer enable message:
-> bearer
-> name
[ -> domain ]
[
-> properties
-> priority
]
Netlink logical layout of bearer disable message:
-> bearer
-> name
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mergeable buffer is used, vnet_hdr_sz is greater than sizeof struct
virtio_net_hdr. So we need advance the iov iterators in this case.
Fixes 6c36d2e26c ("macvtap: Use iovec iterators")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: adjust rx functions
v3:
For patch #1, remove unnecessary initialization for ret and
unnecessary blank line in r8152_submit_rx().
v2:
For patch #1, set actual_length to 0 before adding the rx to the
list, when a error occurs.
For patch #2, change the flow. Stop submitting the rx if a error
occurs, and add the remaining rx to the list for submitting later.
v1:
Adjust some flows and codes which are relative to r8152_submit_rx()
and rtl_start_rx().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a error for r8152_submit_rx(), add the remaining rx
buffers to the list. Then the remaining rx buffers could be
submitted later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The behavior of handling the returned status from r8152_submit_rx()
is almost same, so let r8152_submit_rx() deal with the error
directly. This could avoid the duplicate code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's just silly to hold the skb destructor argument around inside
skb->cb[] as we currently do in SCTP.
Nowadays, we're sort of cheating on data accounting in the sense
that due to commit 4c3a5bdae2 ("sctp: Don't charge for data in
sndbuf again when transmitting packet"), we orphan the skb already
in the SCTP output path, i.e. giving back charged data memory, and
use a different destructor only to make sure the sk doesn't vanish
on skb destruction time. Thus, cb[] is still valid here as we
operate within the SCTP layer. (It's generally actually a big
candidate for future rework, imho.)
However, storing the destructor in the cb[] can easily cause issues
should an non sctp_packet_set_owner_w()'ed skb ever escape the SCTP
layer, since cb[] may get overwritten by lower layers and thus can
corrupt the chunk pointer. There are no such issues at present,
but lets keep the chunk in destructor_arg, as this is the actual
purpose for it.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To help troubleshoot heavy memory pressure conditions, add a bunch of
statistics counter to log RX buffer allocation and RX/TX DMA mapping
failures. These are reported like any other counters through the ethtool
stats interface.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To help troubleshoot heavy memory pressure conditions, add a bunch of
statistics counter to log RX buffer allocation and RX/TX DMA mapping
failures. These are reported like any other counters through the ethtool
stats interface.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending packets out with PF_PACKET, SOCK_RAW, ensure that the
packet is at least as long as the device's expected link layer header.
This check already exists in tpacket_snd, but not in packet_snd.
Also rate limit the warning in tpacket_snd.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
sched: introduce vlan action
Please see the individual patches for info
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This tc action allows to work with vlan tagged skbs. Two supported
sub-actions are header pop and header push.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So it can be used from out of openvswitch code.
Did couple of cosmetic changes on the way, namely variable naming and
adding support for 8021AD proto.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
note that skb_make_writable already exists in net/netfilter/core.c
but does something slightly different.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a need for helper which inserts vlan tag but does not free the
skb in case of an error.
Suggested-by: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use them to push skb->vlan_tci into the payload and avoid code
duplication.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
