Fix pointer to setup_link for 82599.
This resolves some link issues when advertising modes unsupported
by the link partner.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The way __ixgbe_notify_dca() was currently set up it would not be
possible to add a requester. Both cases of the IXGBE_FLAG_DCA_ENABLED
bit being on and off would lead to the function exiting for a
DCA_PROVIDER_ADD.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
after review of all intel drivers, found several instances where
drivers had the incorrect pattern of:
memory mapped write();
delay();
which should always be:
memory mapped write();
write flush(); /* aka memory mapped read */
delay();
explanation:
The reason for including the flush is that writes can be held
(posted) in PCI/PCIe bridges, but the read always has to complete
synchronously and therefore has to flush all pending writes to a
device. If a write is held and followed by a delay, the delay
means nothing because the write may not have reached hardware
(maybe even not until the next read)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Private rx_csum flags are now duplicate of netdev->features &
NETIF_F_RXCSUM. We remove those duplicates and now use the net_device_ops
ndo_set_features. This was based on the original patch submitted by
Michal Miroslaw <mirq-linux@rere.qmqm.pl>. I also removed the special
case not requiring a reset for X540 hardware. It is needed just as it is
in 82599 hardware.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Martin Wilck <martin.wilck@ts.fujitsu.com> reported that systems using
the ixgbe-driver that were capable of WoL were rebooting almost as soon
as they were shut down. This is because the default WoL settings
enabled magic packet, broadcast, unicast, and multicast.
Other Intel devices seem to use the stored eeprom value for initial WoL
capabilities. The 82578DM (e1000e) and 82576 (igb) the devices I looked
at had only the magic packet enabled in the eeprom, so that seems
appropriate on ixgbe-based devices as well. I set the WoL options on my
82578DM to be the same default as the ixgbe devices (umbg) and saw the
same as Martin -- almost as soon as my box shutdown, it booted again.
This patch changes the default to only be the magic packet. This is the
same as the default for most Intel and non-Intel hardware currently
upstream.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Martin Wilck <martin.wilck@ts.fujitsu.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to address possible race conditions from the status
and error bits on the RX descriptors being re-read by multiple functions in
the RX cleanup path. To resolve this I have added code that will pass the
staterr value to those functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves work_limit, total_packets, and total_bytes into the ring
container struct of the q_vector. The advantage of this is that it should
reduce the size of memory used in the event of multiple rings being
assigned to a single q_vector. In addition it should help to reduce the
total workload for calculating itr since now total_packets and total_bytes
will be the total work done of the interrupt instead of for the ring.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for a ring container structure to be used within
the q_vector. The basic idea is to provide a means of separating the RX
and TX rings while maintaining a common structure for their containment.
The advantage to this is that later we should be able to pass this
structure to the update_itr functions without needing to pass individual
rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_maybe_stop_tx function is only a few lines long and is called
multiple times through the xmit hotpath. In order to streamline things it
makes sense to just inline it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to update ATR so that it will use the recorded RX
queue instead of the CPU in the case of routing. This change is meant to
help ixgbe default behavior to more closely match that of the kernel.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix makes it so that the fdir_perfect_lock is initialized in all
cases. This is necessary as the fdir_filter_exit routine will always
attempt to take the lock before inspecting the filter table.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement DCB ops dcb_ieee_del() and set FCoE to the default
priority when no priority exists.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The fcoe.tc field is no longer used so remove it. After
the field is removed there is no need to keep fcoe_setapp()
around so remove it as well. And finally we can get rid
of some DCB #ifdef's in the fcoe code.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit,
commit c8ca76ebc6
Author: John Fastabend <john.r.fastabend@intel.com>
Date: Sat Mar 12 03:50:53 2011 +0000
ixgbe: DCB, further cleanups to app configuration
Removed the getapp() routines from ixgbe because they are no
longer needed. It also allowed the set hardware routines to
use both IEEE 802.1Qaz app types and CEE app types. This
added code to do bit shifting in the IEEE case.
This patch reverts the checks and handles the IEEE case
from the setapp entry point. I prefer this because it
keeps the two paths from having to be aware of the DCB
mode. This resolves a bug where I missed setting the
selector bit in the IEEE spec value and left it in the
CEE value. Now that they are separate routines these types
of errors should not occur.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a need to configure MMW_SIZE in register RTTBCNRM with a correct
value (0x4 for non jumbo frames and 0x14 for jumbo frames support).
For 82599 the value is 0x4 and for X540 the value is 0x14.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the current methods used for determining if we have
enough space to transmit a given skb. The current method is quite wasteful
as it has us go through and determine how each page is going to be broken
up. That only needs to be done if pages are larger than our maximum data
per TXD. As such I have wrapped that in a page size check.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a significant amount of shared functionality between the checksum
and TSO offload configuration that is shared in regards to how they setup
the context descriptors. Since so much of the functionality is shared it
makes sense to move the shared functionality into a single function and
just call that function from the two context descriptor specific routines.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updates all values dealing with count, next_to_use, and
next_to_clean so that they stay u16 values. The advantage of this is that
there is no re-casting of type during the propagation through the stack.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is a minor cleanup that converts the IXGBE_DESC_UNUSED macro
into a static inline function just for the case of the code being a bit
cleaner.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we pass the adapter struct instead of the
netdev for most of the basic interrupts that are not associated with
q_vectors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the ixgbe driver version string to better match the Source Driver
with similar device support. Likewise update to the current LAD Linux
versioning scheme.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes the fact that we would trigger a null pointer dereference
or specify the wrong ring if the rings were restored. This change makes
certain that the DROP queue is a static value, and all other rings are
based on the ring offsets for the PF.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disabling Rx checksumming leads to performance degradation due to
RSC causing packets to have incorrect checksums.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move reset code into a separate function to allow for reuse in other
parts of the code.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move setting RSC into a separate function to allow for reuse in other
parts of the code.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to allow for nfc to insert and remove filters in order
to test the ethtool interface which includes it's own rules manager.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code adds support for displaying the filters that were added via the
nfc interface. This is primarily to test the interface for now, but I am
also looking into the feasibility of moving all of the ntuple filter code
in ixgbe over to the nfc interface since it seems to be better implemented.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds basic support for the obtaining of RSS ring counts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to update the internal framework of ixgbe so that
perfect filters can be stored and tracked via software.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I am removing the requirement that Ntuple filters have the same
number of queues and requirements as ATR. As a result this change will
make it so that all the Ntuple flag does is disable ATR for now.
This change fixes an issue in which we were incorrectly re-enabling ATR
when we exited perfect filter mode. This was due to the fact that the
logic assumed RSS and DCB were mutually exclusive which is no longer the
case.
To correct this we just need to add a check to guarantee DCB is disabled
before re-enabling ATR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to numerous issues in ntuple filters it has been decided to move the
interface over to the network flow classification interface. As a first
step to achieving this I first need to remove the old ntuple interface.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently single PCI pool used across all CPUs and that
doesn't scales up as number of CPU increases, so this
patch adds per CPU PCI pool to setup udl and that aligns
well from FCoE stack as that already has per CPU exch locking.
Adds per CPU PCI alloc setup and free in
ixgbe_fcoe_ddp_pools_alloc and ixgbe_fcoe_ddp_pools_free,
use CPU specific pool during DDP setup.
Re-arranged ixgbe_fcoe struct to have fewer holes
along with adding pools ptr using pahole.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for Dell CEM (Comprehensive Embedded Management)).
This consists of informing the management firmware of the driver version
during probe on 82599 and X540 HW.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_dcb_txq_to_tc() routine was used to map TX rings to
a DCB traffic class. Now that a tx_ring has a DCB traffic class
associated with it this routine is no longer needed.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now flow directors perfect filters features can coexist with DCB.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This bit mask is wrong DCBX_HOST is always set. It was missed up
until now because lldpad reprograms the device on a link
event. However this is still wrong and it is best not to be
mis-configured for some time immediately following ixgbe_up().
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setup RSS redirection table to be compatible with multiple packet
buffers. Currently, this works on 82599 devices because the RSS
redirection index is masked by the number of queues per packet
buffer.
This sets the cap on the RSS table to maxq.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The tx_idx and rx_idx values are swapped on 82598 devices
with DCB enabled.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The number of TX and RX queues allocated depends on the device
type, the current features set, online CPUs, and various
compile flags.
To enable DCB with multiple queues and allow it to coexist with
all the features currently implemented it has to setup a valid
queue count. This is done at init time using the FDIR and RSS
max queue counts and allowing each TC to allocate a queue per
CPU.
DCB will now use available queues up to (8 x TCs) this is somewhat
arbitrary cap but allows DCB to use up to 64 queues. Its easy to
increase this later if that is needed.
This is prep work to enable Flow Director with DCB. After this
DCB can easily coexist with existing features and no longer
needs its own DCB feature ring.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe devices support different numbers of packet buffers either
8 or 4. Here we only allocate the minimal number of packet
buffers required to implement the net_devices number of traffic
classes.
Fewer traffic classes allows for larger packet buffers in
hardware. Also more Tx/Rx queues can be given to each
traffic class.
This patch is mostly about propagating the number of traffic
classes through the init path. Specifically this adds the 4TC
cases to the MRQC and MTQC setup routines. Also ixgbe_setup_tc()
was sanitized to handle other traffic class value.
Finally changing the number of packet buffers in the hardware
requires the device to reinit. So this moves the reinit work
from DCB into the main ixgbe_setup_tc() routine to consolidate
the reset code. Now dcbnl_xxx ops call ixgbe_setup_tc() to
configure packet buffers if needed.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MRQC and MTQC registers are configured in the main
setup path but are also reconfigured in the DCB setup
path. The DCB path fixes the DCB configuration by configuring
the SECTXMINIFG gap which is required for DCB pause
to operate correctly.
This patch reduces the duplicate code and does all setup
in ixgbe_setup_mtqc() and ixgbe_setup_mrqc().
Additionally, this removes the IXGBE_QDE. This write never
set the WRITE bit in the register so the write was not
actually doing anything. Also this was to clear the register
but, it is never set and defaults to zero. If this is
needed for SRIOV it should be added correctly in a follow
up patch. But it's never been working so removing it here
should be OK.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Consolidate packet buffer allocation currently being
done in the DCB path and main path. This allows the
feature set and packet buffer requirements to be done
once.
This is prep work to allow DCB to coexist with other
features namely, flow director.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace duplicated code in if/else branches with single
check and ixgbe_init_interrupt_scheme().
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semicolons are not necessary after switch/while/for/if braces
so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout. Give
them an explicit include via the following $0.02 script.
=========================================
#!/bin/bash
MANUAL=""
for i in `git grep -l 'prefetch(.*)' .` ; do
grep -q '<linux/prefetch.h>' $i
if [ $? = 0 ] ; then
continue
fi
( echo '?^#include <linux/?a'
echo '#include <linux/prefetch.h>'
echo .
echo w
echo q
) | ed -s $i > /dev/null 2>&1
if [ $? != 0 ]; then
echo $i needs manual fixup
MANUAL="$i $MANUAL"
fi
done
echo ------------------- 8\<----------------------
echo vi $MANUAL
=========================================
Signed-off-by: Paul <paul.gortmaker@windriver.com>
[ Fixed up some incorrect #include placements, and added some
non-network drivers and the fib_trie.c case - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
This patch adds support for a new adapter in the 82599 family. Included
in that support is a new media_type ixgbe_media_type_fiber_lco.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
