Commit Graph

100199 Commits

Author SHA1 Message Date
Nishanth Menon
68e4d9e58d ARM: dts: dra7-evm: Fix spi1 mux documentation
While auditing the various pin ctrl configurations using the following
command:
grep PIN_ arch/arm/boot/dts/dra7-evm.dts|(while read line;
do
	v=`echo "$line" | sed -e "s/\s\s*/|/g" | cut -d '|' -f1 |
		cut -d 'x' -f2|tr [a-z] [A-Z]`;
	HEX=`echo "obase=16;ibase=16;4A003400+$v"| bc`;
	echo "$HEX ===> $line";
done)
against DRA75x/74x NDA TRM revision S(SPRUHI2S August 2014),
documentation errors were found for spi1 pinctrl. Fix the same.

Fixes: 6e58b8f1da ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-04 12:47:50 -07:00
Roger Quadros
331bbb595e ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select
functionality. So both can't be enabled simultaneously.

Disable QSPI node to prevent the pin conflict as well as
be similar to 3.12 release.

CC: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-04 12:39:29 -07:00
Roger Quadros
2b54057c9b ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.

So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.

Sanity check wait pin number irrespective if read/write monitoring is
set or not.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-04 12:39:22 -07:00
Roger Quadros
e47acd9626 ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.

Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-04 12:39:15 -07:00
Roger Quadros
302946dee9 ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.

This patch also gets rid of the below warning when NAND is
accessed for the first time.

omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable)

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-04 12:39:08 -07:00
Roger Quadros
6b86911005 ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.

For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-04 12:39:01 -07:00
Roger Quadros
db01e6c7fb ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.

For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-04 12:38:22 -07:00
Felipe Balbi
4b143f0f60 ARM: dts: am4372: fix USB regs size
Size should be 64KiB instead of 92KiB.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-03 14:48:37 -07:00
Nishanth Menon
9316641330 ARM: dts: am437x-gp: switch i2c0 to 100KHz
On the GP EVM, the ambient light sensor is limited to 100KHz on the
I2C bus.

So use 100kHz for I2C on the GP EVM due to this limitation on the
ambient light sensor.

Reported-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-03 14:46:55 -07:00
Tony Lindgren
5c01d5d134 Merge branch 'for-v3.17-rc/ti-clk-dt' of github.com:t-kristo/linux-pm into fixes-rc3 2014-09-03 14:39:51 -07:00
Roger Quadros
f0e9fab3bc ARM: dts: dra7-evm: Fix 8th NAND partition's name
The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.

CC: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-03 14:32:35 -07:00
Roger Quadros
544d63d0f3 ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
The I2C3 pins are taken from pads E21 (GPIO6_14) and
F20 (GPIO6_15). Use the right pinmux register and mode.

Also set the I2C3 bus frequency to a safer 400KHz than
3.4Mhz.

CC: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-03 14:32:00 -07:00
Linus Torvalds
05bdb8c90e Xtensa improvements for 3.17:
- support highmem on cores with aliasing data cache. Enable highmem on kc705
   by default;
 - simplify addition of new core variants (no need to modify Kconfig /
   Makefiles);
 - improve robustness of unaligned access handler and its interaction with
   window overflow/underflow exception handlers;
 - deprecate atomic and spill registers syscalls;
 - clean up Kconfig: remove orphan MATH_EMULATION, sort 'select' statements;
 - wire up renameat2 syscall.
 
 Various fixes:
 - fix address checks in dma_{alloc,free}_coherent (runtime BUG);
 - fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage);
 - fix TLBTEMP_BASE_2 region handling in fast_second_level_miss (runtime
   unrecoverable exception);
 - fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace register
   clobbering);
 - fix kernel/user jump out of fast_unaligned (potential runtime unrecoverabl
   exception);
 - replace termios IOCTL code definitions with constants (userspace build
   breakage).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJUA2nrAAoJEI9vqH3mFV2sqS4P/j6+wtuPHhvNLmpzlIJ1//OP
 zr6o4eRC77HDS0ArqFq+mteU8MH2CXoiMOFvUzXSyistSrQyENJ5Mg8f5vY9sqeJ
 PQtHzBIg7gBpJTiI66n5k+Av65KdcLdz3JE9j1IHXy+Ovlv+BVAOBWfb6Mx59a5i
 4rk+ovSrKbAOI50RBL4p/YpCgxu0hdpnpVJ0Ng7ApSXq18o9uxLdgekn11ZJFtob
 hFgdh4i5Rg+hL+HV8ehE7K5xwxVaqU//dgdbCVB2g3gcNGaDINiEwyJBxWszln4W
 wKr9kSCnHihSevDNby/AIw01d1HS18wZdIjTn10/jRnz9PzIET14K2lmqaU6+RyC
 un8EZW3R0jabMMJ7DqKCiLK6Adz+lNuhs4hx7oGNJIuvyILiSrgqVQEDtwTJDNPk
 43lcBYVgpaFviP0exMl9AUb12s8aIhN7D9vFguyuV7Rl8vgUIsEhE67CrIjvi2Hp
 FV4s1+tVylFYCLbBITPtztfDKiJH4WUbaUGmiK27ReE8L7fAU2jicTau31r0L3ca
 66FdInbchvl4TgZBi2ndEsVOmqKc7V8o0Xb+Cmgdda5mgZRw5y8KGnSi9I1YhPc0
 xNZq1P6W5HcWbH0kFIRtnRJmGJjtHu+T5Z12yZ+o9EmMXfCePtUSUrMq8YkW/lMg
 tJCSbnosd4z498k7hFHY
 =mAYX
 -----END PGP SIGNATURE-----

Merge tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux

Pull Xtensa updates from Chris Zankel:
 "Xtensa improvements for 3.17:
   - support highmem on cores with aliasing data cache.  Enable highmem
     on kc705 by default
   - simplify addition of new core variants (no need to modify Kconfig /
     Makefiles)
   - improve robustness of unaligned access handler and its interaction
     with window overflow/underflow exception handlers
   - deprecate atomic and spill registers syscalls
   - clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
     statements
   - wire up renameat2 syscall.

  Various fixes:
   - fix address checks in dma_{alloc,free}_coherent (runtime BUG)
   - fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
   - fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
     (runtime unrecoverable exception)
   - fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
     register clobbering)
   - fix kernel/user jump out of fast_unaligned (potential runtime
     unrecoverabl exception)
   - replace termios IOCTL code definitions with constants (userspace
     build breakage)"

* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
  xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
  xtensa: don't allow overflow/underflow on unaligned stack
  xtensa: fix a6 and a7 handling in fast_syscall_xtensa
  xtensa: allow single-stepping through unaligned load/store
  xtensa: move invalid unaligned instruction handler closer to its users
  xtensa: make fast_unaligned store restartable
  xtensa: add double exception fixup handler for fast_unaligned
  xtensa: fix kernel/user jump out of fast_unaligned
  xtensa: configure kc705 for highmem
  xtensa: support highmem in aliasing cache flushing code
  xtensa: support aliasing cache in kmap
  xtensa: support aliasing cache in k[un]map_atomic
  xtensa: implement clear_user_highpage and copy_user_highpage
  xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
  xtensa: allow fixmap and kmap span more than one page table
  xtensa: make fixmap region addressing grow with index
  xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
  xtensa: add renameat2 syscall
  xtensa: fix address checks in dma_{alloc,free}_coherent
  xtensa: replace IOCTL code definitions with constants
  ...
2014-08-31 17:08:42 -07:00
Guenter Roeck
ca98565a61 unicore32: Fix build error
unicore32 builds fail with

  arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
  arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
  arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
  arch/unicore32/kernel/signal.c: In function ‘do_signal’:
  arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
  make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
  make: *** [arch/unicore32/kernel/signal.o] Error 2

Bisect points to commit 649671c90e ("unicore32: Use get_signal()
signal_setup_done()").

This code never even compiled.  Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up.  Compile
tested only.

Fixes: 649671c90e ("unicore32: Use get_signal() signal_setup_done()")
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-31 17:08:12 -07:00
Linus Torvalds
94559a4a81 Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
 "Various assorted fixes:

   - a couple of patches from Mark Rutland to resolve an errata with
     Cortex-A15 CPUs.
   - fix cpuidle for the CPU part ID changes in the last merge window
   - add support for a relocation which ARM binutils is generating in
     some circumstances"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
  ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
  ARM: 8128/1: abort: don't clear the exclusive monitors
  ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations
2014-08-31 17:02:57 -07:00
Linus Torvalds
19ed3eb975 ARM: SoC fixes for 3.17-rc
Here's the weekly batch of fixes from arm-soc.
 
 The delta is a largeish negative delta, due to revert of SMP support for Broadcom's
 STB SoC -- it was accidentally merged before some issues had been addressed, so they
 will make a new attempt for 3.18. I didn't see a need for a full revert of the whole
 platform due to this, we're keeping the rest enabled.
 
 The rest is mostly:
 
 * A handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
 * Some MTD/NAND fixes for OMAP
 * Minor DT fixes for shmobile
 * Warning fix for UP builds on vexpress/spc
 
 There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
 so it can boot. Drivers and the rest had landed for 3.17, and it's small
 and isolated so it made sense to pick up now even if it's not a bugfix.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJUA1uwAAoJEIwa5zzehBx3dV8QAJv/6OcFofqWPqSapCdcCTkU
 o9o+QxzTY4Fo4GDyTboLwvY2EE7aFKohiekKGoHHT+fXXR4n+/Xe5Dq58DijdZ0q
 xUksd1h1ZuqzbWqT+1fyrlgJt3jOmQ1vzbBVpWA4tN1RUKJekU+ZF0oCAAdDwbaf
 O925etd77+ij0euJ/l06fR9YUYIY23mufG+SELke5S7xS9T1sVFWcluf/z+y57qc
 hxF6Uc5r4LOY4pFKYgjvsu3R7KPD4DANCiSYUvjS5sIWrJ3xenkyHVMxFEyQ5Tz+
 TCrT8rXx3Ue7AlNMztY5P1dTmYftwJhWy6p/8J8UqPJ6ip633FWrhTfKHmLIR3lC
 VkMYroFeg4Fp/YvFENeBe9QUbg0Xb920oZoDQA4SwkZJkQlWafYsOy4bLKSyMQGQ
 nKcnyxeP2q5YaStTZMSNQ4xwT9yo3dwBllYGSbXUiTk0VJ3TX9jEMg6StvRM0YHG
 sT8XKufqIAJugNZZsGtGyBLO6f8BbPVgFICvEVetgjMWHl9iGNVDbeqbYvQ6A8NL
 TTqJUK7CXkNgQGX2rB7txSgR3XoaWU0rWjSnSXy2Xgtb/pd/jZYLicEY8Wd4Q1qp
 Ww2misiX4viMxcD6AWiDUj1mcciSh915h1po5zZbLMTRp4qfuqh1BfSvPY/fh5DD
 LKXAwm3PyL9+QrknP3//
 =/AD8
 -----END PGP SIGNATURE-----

Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Here's the weekly batch of fixes from arm-soc.

  The delta is a largeish negative delta, due to revert of SMP support
  for Broadcom's STB SoC -- it was accidentally merged before some
  issues had been addressed, so they will make a new attempt for 3.18.
  I didn't see a need for a full revert of the whole platform due to
  this, we're keeping the rest enabled.

  The rest is mostly:

   - a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
   - some MTD/NAND fixes for OMAP
   - minor DT fixes for shmobile
   - warning fix for UP builds on vexpress/spc

  There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
  so it can boot.  Drivers and the rest had landed for 3.17, and it's
  small and isolated so it made sense to pick up now even if it's not a
  bugfix"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  vexpress/spc: fix a build warning on array bounds
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
  MAINTAINERS: catch special Rockchip code locations
  ARM: dts: microsom-ar8035: MDIO pad must be set open drain
  ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
  ARM: brcmstb: revert SMP support
  ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
  ARM: dts: Enable UART wake-up events for beagleboard
  ARM: dts: Remove twl6030 clk32g "regulator"
  ARM: OMAP2+: omap_device: remove warning that clk alias already exists
  ARM: OMAP: fix %d confusingly prefixed with 0x in format string
  ARM: dts: DRA7: fix interrupt-cells for GPIO
  mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
  ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
  ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
  mtd: nand: omap: Revert to using software ECC by default
  ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
  ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
  ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
  ...
2014-08-31 17:01:19 -07:00
Alex Shi
e160cc1768 vexpress/spc: fix a build warning on array bounds
With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:

arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
  struct ve_spc_opp *opps = info->opps[cluster];
                                      ^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.

Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2014-08-31 10:22:10 -07:00
Olof Johansson
98fd150836 Add basic subarchitecture support for the DRA72x and DRA74x. These
are OMAP2+ derivative SoCs.  This should be low-risk to existing OMAP
 platforms.
 
 Basic build, boot, and PM test logs are available here:
 
 http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJT/saeAAoJEMePsQ0LvSpLKzgP+gK9LdsoYrsyVqDp7ZbSSzSy
 scrlTlTa6iO+Et82TLDPEoWgsNb7BXSJDHWF6j5GxzSsZIM8hm2LEjvhvkf0BuHt
 n8J1+uZduIZLEipBb2gLCY2td2hYrM8UUwNgLk3oFHf6uhLKrdK0WUzdBr6Aznlb
 J+l42Pds2AI37tf7Fa3d1ZVEQhMrZb61g6SD77S2KdifL0rlWpE+rDaGBr71qBi5
 CXibrKi2NikNGKHKdusLPCCcvo/tfpf3o32olO1W72kFbC8eTy2nZLj1qaxnLvbr
 DfOzZDWEdS4I2AXrhh/EYiL298FecOtty3FX++/W2XWiM9VYq/wKYthBM/qrGous
 tpnsbTEt7BhIaCwJte0xpwTeCLnke9se1aD+GptyPCOI7jQxG0CCWtd5gKeIIiEO
 YrNZjjIXDOL6HZgVuETGuVf6NJYfjThZ8yglvnX6hr5awdcBao5yhb/AkdM629mB
 ackueKLS0zysQo9p9LlwnqvUVU4PJHBmkyzBtUKDbv2FD/IFuvZm4ZaPR28eim+1
 N17qTIdQPog2+4sxKQA96uj7n38K0UPFkgIbi7B25YFpSTPLAu4COiJeS45K8tWv
 yWocbzPQPd5KVWXWxD/HfaQjKGUHbQQpNeJHn6CyQSqXTpPwzkVembC8gCL3gxed
 CQaowzZfGWl0oDoLVXCy
 =5ZS8
 -----END PGP SIGNATURE-----

Merge tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes

Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:

Add basic subarchitecture support for the DRA72x and DRA74x.  These
are OMAP2+ derivative SoCs.  This should be low-risk to existing OMAP
platforms.

Basic build, boot, and PM test logs are available here:

http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/

* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-08-31 10:19:43 -07:00
Linus Torvalds
fd5984d7c8 Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
 "One patch to avoid assigning interrupts we don't actually have on
  non-PC platforms, and two patches that addresses bugs in the new
  IOAPIC assignment code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, irq, PCI: Keep IRQ assignment for runtime power management
  x86: irq: Fix bug in setting IOAPIC pin attributes
  x86: Fix non-PC platform kernel crash on boot due to NULL dereference
2014-08-29 17:22:27 -07:00
Linus Torvalds
10f3291a1d Merge branch 'akpm' (fixes from Andrew Morton)
Merge patches from Andrew Morton:
 "22 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
  kexec: purgatory: add clean-up for purgatory directory
  Documentation/kdump/kdump.txt: add ARM description
  flush_icache_range: export symbol to fix build errors
  tools: selftests: fix build issue with make kselftests target
  ocfs2: quorum: add a log for node not fenced
  ocfs2: o2net: set tcp user timeout to max value
  ocfs2: o2net: don't shutdown connection when idle timeout
  ocfs2: do not write error flag to user structure we cannot copy from/to
  x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
  drivers/rtc/rtc-s5m.c: re-add support for devices without irq specified
  xattr: fix check for simultaneous glibc header inclusion
  kexec: remove CONFIG_KEXEC dependency on crypto
  kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
  x86,mm: fix pte_special versus pte_numa
  hugetlb_cgroup: use lockdep_assert_held rather than spin_is_locked
  mm/zpool: use prefixed module loading
  zram: fix incorrect stat with failed_reads
  lib: turn CONFIG_STACKTRACE into an actual option.
  mm: actually clear pmd_numa before invalidating
  memblock, memhotplug: fix wrong type in memblock_find_in_range_node().
  ...
2014-08-29 16:28:29 -07:00
Michael Welling
b0108f9e93 kexec: purgatory: add clean-up for purgatory directory
Without this patch the kexec-purgatory.c and purgatory.ro files are not
removed after make mrproper.

Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-29 16:28:17 -07:00
Pranith Kumar
e356030519 flush_icache_range: export symbol to fix build errors
Fix building errors occuring due to a missing export of
flush_icache_range() in

kisskb.ellerman.id.au/kisskb/buildresult/11677809/

ERROR: "flush_icache_range" [drivers/misc/lkdtm.ko] undefined!

Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>	[arc]
Acked-by: Richard Kuo <rkuo@codeaurora.org>	[hexagon]
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>	[xtensa]
Cc: Noam Camus <noamc@ezchip.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Zhigang Lu <zlu@tilera.com>		[tile]
Cc: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-29 16:28:17 -07:00
Vivek Goyal
4df4185a59 x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
Thomas reported that build of x86_64 kernel was failing for him.  He is
using 32bit tool chain.

Problem is that while compiling purgatory, I have not specified -m64
flag.  And 32bit tool chain must be assuming -m32 by default.

Following is error message.

(mini) [~/work/linux-2.6] make
scripts/kconfig/conf --silentoldconfig Kconfig
  CHK     include/config/kernel.release
  UPD     include/config/kernel.release
  CHK     include/generated/uapi/linux/version.h
  CHK     include/generated/utsrelease.h
  UPD     include/generated/utsrelease.h
  CC      arch/x86/purgatory/purgatory.o
arch/x86/purgatory/purgatory.c:1:0: error: code model 'large' not supported in
the 32 bit mode

Fix it by explicitly passing appropriate -m64/-m32 build flag for
purgatory.

Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-29 16:28:16 -07:00
Vivek Goyal
b41d34b46a kexec: remove CONFIG_KEXEC dependency on crypto
New system call depends on crypto.  As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.

But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto.  Remove that dependency.

Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-29 16:28:16 -07:00
Vivek Goyal
74ca317c26 kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
Currently new system call kexec_file_load() and all the associated code
compiles if CONFIG_KEXEC=y.  But new syscall also compiles purgatory
code which currently uses gcc option -mcmodel=large.  This option seems
to be available only gcc 4.4 onwards.

Hiding new functionality behind a new config option will not break
existing users of old gcc.  Those who wish to enable new functionality
will require new gcc.  Having said that, I am trying to figure out how
can I move away from using -mcmodel=large but that can take a while.

I think there are other advantages of introducing this new config
option.  As this option will be enabled only on x86_64, other arches
don't have to compile generic kexec code which will never be used.  This
new code selects CRYPTO=y and CRYPTO_SHA256=y.  And all other arches had
to do this for CONFIG_KEXEC.  Now with introduction of new config
option, we can remove crypto dependency from other arches.

Now CONFIG_KEXEC_FILE is available only on x86_64.  So whereever I had
CONFIG_X86_64 defined, I got rid of that.

For CONFIG_KEXEC_FILE, instead of doing select CRYPTO=y, I changed it to
"depends on CRYPTO=y".  This should be safer as "select" is not
recursive.

Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Tested-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-29 16:28:16 -07:00
Hugh Dickins
b38af4721f x86,mm: fix pte_special versus pte_numa
Sasha Levin has shown oopses on ffffea0003480048 and ffffea0003480008 at
mm/memory.c:1132, running Trinity on different 3.16-rc-next kernels:
where zap_pte_range() checks page->mapping to see if PageAnon(page).

Those addresses fit struct pages for pfns d2001 and d2000, and in each
dump a register or a stack slot showed d2001730 or d2000730: pte flags
0x730 are PCD ACCESSED PROTNONE SPECIAL IOMAP; and Sasha's e820 map has
a hole between cfffffff and 100000000, which would need special access.

Commit c46a7c817e ("x86: define _PAGE_NUMA by reusing software bits on
the PMD and PTE levels") has broken vm_normal_page(): a PROTNONE SPECIAL
pte no longer passes the pte_special() test, so zap_pte_range() goes on
to try to access a non-existent struct page.

Fix this by refining pte_special() (SPECIAL with PRESENT or PROTNONE) to
complement pte_numa() (SPECIAL with neither PRESENT nor PROTNONE).  A
hint that this was a problem was that c46a7c817e added pte_numa() test
to vm_normal_page(), and moved its is_zero_pfn() test from slow to fast
path: This was papering over a pte_special() snag when the zero page was
encountered during zap.  This patch reverts vm_normal_page() to how it
was before, relying on pte_special().

It still appears that this patch may be incomplete: aren't there other
places which need to be handling PROTNONE along with PRESENT?  For
example, pte_mknuma() clears _PAGE_PRESENT and sets _PAGE_NUMA, but on a
PROT_NONE area, that would make it pte_special().  This is side-stepped
by the fact that NUMA hinting faults skipped PROT_NONE VMAs and there
are no grounds where a NUMA hinting fault on a PROT_NONE VMA would be
interesting.

Fixes: c46a7c817e ("x86: define _PAGE_NUMA by reusing software bits on the PMD and PTE levels")
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: <stable@vger.kernel.org>	[3.16]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-29 16:28:16 -07:00
Will Deacon
9e36c63395 alpha: io: implement relaxed accessor macros for writes
write{b,w,l,q}_relaxed are implemented by some architectures in order to
permit memory-mapped I/O writes with weaker barrier semantics than the
non-relaxed variants.

This patch implements these write macros for Alpha, in the same vein as
the relaxed read macros, which are already implemented.

Acked-by: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-29 11:18:45 -07:00
Michael Cree
5691e4456a alpha: Wire up sched_setattr, sched_getattr, and renameat2 syscalls.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-29 11:18:45 -07:00
Jiang Liu
9eabc99a63 x86, irq, PCI: Keep IRQ assignment for runtime power management
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during runtime power
management, otherwise it may cause failure of device wakeups.

Commit 3eec595235 "x86, irq, PCI: Keep IRQ assignment for PCI
devices during suspend/hibernation" has fixed the issue for suspend/
hibernation, we also need the same fix for runtime device sleep too.

Fix: https://bugzilla.kernel.org/show_bug.cgi?id=83271
Reported-and-Tested-by: EmanueL Czirai <amanual@openmailbox.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: EmanueL Czirai <amanual@openmailbox.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1409304383-18806-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2014-08-29 13:38:00 +02:00
Linus Torvalds
2db3cff2d3 Couple of simple fixes due for the 3.17 rcs
(and a sneaky document addition that slipped from the previous pull-request)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJT/0s6AAoJEFGvii+H/HdhNiEP/R+zAKkTCmJyw2aeJR9RrNaO
 Qu2rzavdCsM/DKJiEKsF0QNvyMFM3S1Tx16pnOWcsCdJI9LVgeCRv7Fpn2mJKNRI
 UlmRHuG+SRu2nzr0gc+hyEOuz5VhpGemKo4tntUEPKrj5eXD25e3QgYHFIdTI32k
 c/bG7eKV7LbPSrybzLNw6FNRuH0YyN667PEck1HVFerCv/921LwO4seOVPAwecgu
 tELpaY7oxDTxoPe8QmxzmPWvCri1OjGaQTEfHoCWXfUaeYcOksI4mJ1zoIBZ0aHb
 uSY+wVnXfkAbmz7kzcJJvVYuf4PhI0mRh2uEhpvzJxMaetAA3JVf0/JXOhTGbATK
 itWgSqCVXooMf+8DIEsMkmXgqV0+Nvy0vZxv+viIdQ4ea9nUrWVT+KJmYsKp8lk9
 SAXsDv+4sr3POCN4QwvAsEKmujtngkOws2YSRRZqiPw8DAiNVpjgF/bZ6jZXVvQs
 wpOqGFJhwS3etyBica1hEZorhGoQzLEWgXDa+D+9jPs1TWVBJVYKeGaRFPGVZxgN
 6mAObpbv0/Uc6SUUlv55qfF3A1KUE2n7001SoD7zYEcTQ9jIcqw8CgKlb4kgrROv
 VeFb4wIxF6kGuijiKMZvwoH0x+QL/fXrvIVK6x8UN2Zy3+QMva+x8pu8tZQvTYun
 CibJKkoCwT2dth7D9pWS
 =DaB2
 -----END PGP SIGNATURE-----

Merge tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull mfd fixes from Lee Jones:
 "Couple of simple fixes due for the 3.17 rcs

  (and a sneaky document addition that slipped from the previous
  pull-request)"

* tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators
  mfd: tc3589x: Add device tree bindings
  mfd: ab8500-core: Use 'ifdef' for config options
  mfd: htc-i2cpld: Fix %d confusingly prefixed with 0x in format string
  mfd: omap-usb-host: Fix %d confusingly prefixed with 0x in format string
2014-08-28 10:46:25 -07:00
Tony Lindgren
daebabd578 mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators
Commit 43fef47f94 (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.

This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678ab6 (ARM: dts:
Revert enabling of twl configuration for n900).

Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.

This allows us to enable the PMIC configuration for n900.

Fixes: 43fef47f94 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)

Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-08-28 15:57:55 +01:00
Rajendra Nayak
f7f7a29bf0 ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
To deal with IPs which are specific to dra74x and dra72x, maintain seperate
ocp interface lists, while keeping the common list for all common IPs.

Move USB OTG SS4 to dra74x only list since its unavailable in
dra72x and is giving an abort during boot. The dra72x only list
is empty for now and a placeholder for future hwmod additions which
are specific to dra72x.

Fixes: d904b38df0 ("ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss")
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
[paul@pwsan.com: fixed comment style to conform with CodingStyle]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2014-08-27 19:38:23 -06:00
Rajendra Nayak
af438fec6c ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Use the corresponding compatibles to identify the devices.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2014-08-27 19:38:22 -06:00
Olof Johansson
0dc0d9e18e Renesas ARM Based SoC Clock Fixes For v3.17
* ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
 
   This resolves a problem introduced by 4bfb358b1d
   ("ARM: shmobile: Add r8a7791 legacy SDHI clocks")
   which was included in v3.15.
 
   This fix does not have any run-time affect at this time.
 
 * ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
 
   This resolves a problem introduced by 9f13ee6f83
   ("ARM: shmobile: r8a7790: add div4 clocks")
   which was included in v3.11.
 
   This fix does not have any run-time affect at this time.
 
 * ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
 
   This resolves a problem introduced by a0f7e7496d
   ("ARM: shmobile: sh73a0: add CMT1 clock support for DT")
   which was included in v3.17-rc1.
 
   This fix does not have any run-time affect at this time as the clock in
   question is used by a SCIF device that is not enabled by default.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJT+oE/AAoJENfPZGlqN0++6eYQAK8LStttSbAjBHONrCQpj1/n
 fBu+S9RjzYOKLtG4L7pVXOJSFuIiPB03y4IeiFRflIS6TQyopl7DmTZvN/AztIjE
 dOamQ+Z2ePrLcNUG1ZNfpEUSxfImOqtcm38R58HRDOnMYTszLOaVxtU0Dre9Y3Me
 cYHEN/17PUQWdQ7j5tcaDwXtl4oVjS+1RmzkODKpP2N+1w4l0rcXHEXuNJC6NpW8
 1i2CWnlb64hQ0L1tOBVabmUXmlwbasV5dBnysupn3IZHOMO+liNSb9T2RHpvtKSw
 U4hu4cZXSGNWoFlWzrs7SoJf1uFF0h5GlrgUm5TGPA1oUPsRzJKRS6D70daElmpi
 e5OszD89bs/LftHY4wpcwQ3ic/PSCqMGdF4aFAzVtfseND9tzrK+8aa8GX18bb9R
 hGfEeiXzp2EnIEtBMUmrrk0cV9thx1zuwaGoai0P2E82SXbMglrKYVAm0xN3yxRc
 77u47S479o7xGSdT2/EBX+EIWnFrGZheT10iPc+aEWRRTxWFf5e10j1i3F1Lw7cL
 5P3PNrMUv3s1Vf82gHKfdtlaYZZoMuF3r03ezt2EScg9MDxhytBDHxiokfw7NRdA
 OA8IaXuoU4MSXArgkdJ89kzV1AnK8aMGlQY/BXfjPqgPUGRQ8TK/sEDp2I5poMeZ
 t2xCtxUvCA39NM/xBDyS
 =jurT
 -----END PGP SIGNATURE-----

Merge tag 'renesas-clock-fixes-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

Merge "Renesas ARM Based SoC Clock Fixes For v3.17" from Simon Horman:

* ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR

  This resolves a problem introduced by 4bfb358b1d
  ("ARM: shmobile: Add r8a7791 legacy SDHI clocks")
  which was included in v3.15.

  This fix does not have any run-time affect at this time.

* ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR

  This resolves a problem introduced by 9f13ee6f83
  ("ARM: shmobile: r8a7790: add div4 clocks")
  which was included in v3.11.

  This fix does not have any run-time affect at this time.

* ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name

  This resolves a problem introduced by a0f7e7496d
  ("ARM: shmobile: sh73a0: add CMT1 clock support for DT")
  which was included in v3.17-rc1.

  This fix does not have any run-time affect at this time as the clock in
  question is used by a SCIF device that is not enabled by default.

* tag 'renesas-clock-fixes-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
  ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
  ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-08-27 15:14:05 -07:00
Olof Johansson
e1e5b71843 i.MX fixes for 3.17, 2nd take:
- Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
    configuration missing
  - A couple small SolidRun board fixes/correction from Rabeeh
    and Russell
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJT/XBJAAoJEFBXWFqHsHzOuqgH/3XqY4n0kL7lZQGRl8sBA/1m
 bLtlKYaGjtn5ITXYONuWyxk9MrkCUaVUEEkcM3Gty6kHbCZ9F8nqSa5NiYs4MyGR
 FiBX1GANmz96t61i90jlNNxHdPfnmgj3ZXEDTEj9g2brwGceUgQZv4/D59qSy41H
 VlyIIOREQbrIoFlln1cEaKf2UXOpmSpB835QHROwy9K4aK0kZKAR4v5eqM2aQaIl
 9VpvR5Xfsmr5vH/srlkY+Vc2ODVF1nQZsa3ikleAh2rzFQ4thwSKqpSxF7HL6EAo
 zafJuI67ctyzIFk1PlsUuqCM2NimzACnpgrNG6Vn2KDq/JavNIsuyna0KgzzXqE=
 =jOFz
 -----END PGP SIGNATURE-----

Merge tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Merge "ARM: imx: fixes for 3.17, 2nd take" from Shawn Guo:

i.MX fixes for 3.17, 2nd take:
 - Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
   configuration missing
 - A couple small SolidRun board fixes/correction from Rabeeh
   and Russell

* tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: microsom-ar8035: MDIO pad must be set open drain
  ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
  ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
  ARM: dts: imx53-qsrb: Fix suspend/resume

Signed-off-by: Olof Johansson <olof@lixom.net>
2014-08-27 15:12:22 -07:00
Olof Johansson
c2e1da63e6 Fixes for omaps, mostly to revert NAND back to using software ECC
by default as that's what many boards expect. Also fixes for omap5
 clocks, PM wake-up events, GPIO interrupt cells for dra7, and few
 other minor fixes.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJT/PNtAAoJEBvUPslcq6VzQsoP/0a2WXN51/oqrhviMGURLDFy
 57Mc6Yz4annJPeyzmD7myPEoppOAzC+Ysp04gC2Ig5ygj94KPJb5Mc2o28lZT4wr
 OTNjQA2W+5CpefXHTRSRaoqcfOD9qUmcnb+rGTiTIxSu8DYxWaf8seAxL2Q2YJ7u
 +DPREfhs0YZyA1kxiZy1xssR2pM1lsPthf0hBDxPyxaTnBxvWFlZAw+06xWVlA+G
 Lk5NZZOFXKTKGV6Cq28q+FQvveUqW3An87pfFZZsSyBQfCIZdNDtCQ7OXCgjA+E2
 OZ7fYh+phbFkr8W+0fJGu3b3t8ehFm74tvQ1qQlb0R0GrqRMaYXooO4Wk73sgJmc
 MbaBGZ7CzkLC7IgvfitbdDRlFmrQeVHoBoH+UtwkNh4CyWtBzdrvxxgj8BvtJSYs
 rWfppeEZrsWKdESNdjV4YFqkrMEHfyOlTjAqDUVd8CjtF1fOyQ/WkfpgqcpsYfj5
 7YhW5qMjtYYmNoklU62sQyJx2HhpYpjdI83qmKT6zUM2OlrJYmco3FFXFRHRfNv2
 o6M61iO+dwYuEjfZ1NhlCep41/MJ2El1oYMnNNvXy/DBveh9887TuX4S5WYIcF2M
 ofhv4y3JDGPfXvvdpE/M1FiqHoJ0Epl+IUbaeNR61mbBmZZG3ExvPiqvYgdrhbnk
 2kr7x8fPRfgsc41z1ajH
 =i+aY
 -----END PGP SIGNATURE-----

Merge tag 'omap-for-v3.17/fixes-against-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Merge "omap fixes against v3.17-rc2" from Tony Lindgren:

Fixes for omaps, mostly to revert NAND back to using software ECC
by default as that's what many boards expect. Also fixes for omap5
clocks, PM wake-up events, GPIO interrupt cells for dra7, and few
other minor fixes.

* tag 'omap-for-v3.17/fixes-against-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
  ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
  ARM: dts: Enable UART wake-up events for beagleboard
  ARM: dts: Remove twl6030 clk32g "regulator"
  ARM: OMAP2+: omap_device: remove warning that clk alias already exists
  ARM: OMAP: fix %d confusingly prefixed with 0x in format string
  ARM: dts: DRA7: fix interrupt-cells for GPIO
  mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
  ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
  ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
  mtd: nand: omap: Revert to using software ECC by default
2014-08-27 15:08:28 -07:00
Juri Lelli
eba1c71819 ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
Commit af040ffc9b ("ARM: make it easier to check the CPU part number
correctly") changed ARM_CPU_PART_X masks, and the way they are returned and
checked against. Usage of read_cpuid_part_number() is now deprecated, and
calling places updated accordingly. This actually broke cpuidle-big_little
initialization, as bl_idle_driver_init() performs a check using an hardcoded
mask on cpu_id.

Create an interface to perform the check (that is now even easier to read).
Define also a proper mask (ARM_CPU_PART_MASK) that makes this kind of checks
cleaner and helps preventing bugs in the future. Update usage accordingly.

Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-08-27 15:40:45 +01:00
Mark Rutland
2c32c65e37 ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
On revisions of Cortex-A15 prior to r3p3, a CLREX instruction at PL1 may
falsely trigger a watchpoint exception, leading to potential data aborts
during exception return and/or livelock.

This patch resolves the issue in the following ways:

  - Replacing our uses of CLREX with a dummy STREX sequence instead (as
    we did for v6 CPUs).

  - Removing the clrex code from v7_exit_coherency_flush and derivatives,
    since this only exists as a minor performance improvement when
    non-cached exclusives are in use (Linux doesn't use these).

Benchmarking on a variety of ARM cores revealed no measurable
performance difference with this change applied, so the change is
performed unconditionally and no new Kconfig entry is added.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-08-27 15:40:13 +01:00
Mark Rutland
8586831317 ARM: 8128/1: abort: don't clear the exclusive monitors
The ARMv6 and ARMv7 early abort handlers clear the exclusive monitors
upon entry to the kernel, but this is redundant:

  - We clear the monitors on every exception return since commit
    200b812d00 ("Clear the exclusive monitor when returning from an
    exception"), so this is not necessary to ensure the monitors are
    cleared before returning from a fault handler.

  - Any dummy STREX will target a temporary scratch area in memory, and
    may succeed or fail without corrupting useful data. Its status value
    will not be used.

  - Any other STREX in the kernel must be preceded by an LDREX, which
    will initialise the monitors consistently and will not depend on the
    earlier state of the monitors.

Therefore we have no reason to care about the initial state of the
exclusive monitors when a data abort is taken, and clearing the monitors
prior to exception return (as we already do) is sufficient.

This patch removes the redundant clearing of the exclusive monitors from
the early abort handlers.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-08-27 15:40:12 +01:00
Andrey Ryabinin
55f0fb6adb ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations
Kernel module build with GCOV profiling fails to load with the
following error:

 $ insmod test_module.ko
   test_module: unknown relocation: 38
   insmod: can't insert 'test_module.ko': invalid module format

This happens because constructor pointers in the .init_array section
have not supported R_ARM_TARGET1 relocation type.

Documentation (ELF for the ARM Architecture) says:
    "The relocation must be processed either in the same way as R_ARM_REL32 or
     as R_ARM_ABS32: a virtual platform must specify which method is used."

Since kernel expects to see absolute addresses in .init_array R_ARM_TARGET1
relocation type should be treated the same way as R_ARM_ABS32.

Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-08-27 15:40:11 +01:00
Jiang Liu
f395dcae7a x86: irq: Fix bug in setting IOAPIC pin attributes
Commit 15a3c7cc91 "x86, irq: Introduce two helper functions
to support irqdomain map operation" breaks LPSS ACPI enumerated
devices.

On startup, IOAPIC driver preallocates IRQ descriptors and programs
IOAPIC pins with default level and polarity attributes for all legacy
IRQs. Later legacy IRQ users may fail to set IOAPIC pin attributes
if the requested attributes conflicts with the default IOAPIC pin
attributes. So change mp_irqdomain_map() to allow the first legacy IRQ
user to reprogram IOAPIC pin with different attributes.

Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1409118795-17046-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2014-08-27 11:02:16 +02:00
Rabeeh Khoury
bf8147208e ARM: dts: microsom-ar8035: MDIO pad must be set open drain
This patch is important for the MicroSOM implementation due to the
following details -

1. VIH of the Atheros phy is 1.7V.
2. NVCC_ENET which is the power domain of the MDIO pad is driven by the
   PHY's LDO (i.e. either 1.8v or 2.5v).
3. The MicroSOM implements an onbouard 1.6kohm pull up to 3.3v (R3000).

In the case the PHY's LDO was 1.8v then there would be only a 100mV
margin for the signal to be acknowledged as high (1.8v-1.7v).
Due to that setting the pad as an open drain will let the 1.6kohm pull
that signal high to 3.3 that assures enough margins to the PHY to be
acked as '1' logic.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-08-27 13:32:26 +08:00
Linus Torvalds
68e370289c Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
 - wire up the system calls seccomp, getrandom and memfd_create
 - use static system information as input to add_device_randomness
 - .. and three bug fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/sclp: remove unnecessary XTABS flag
  s390/3215: fix tty output containing tabs
  s390: wire up memfd_create syscall
  s390: add system information as device randomness
  s390/kdump: Clear subchannel ID to signal non-CCW/SCSI IPL
  s390: wire up seccomp and getrandom syscalls
2014-08-26 13:50:23 -07:00
Tero Kristo
8fd46439e1 ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
Similarly to DRA7, OMAP5 has l3 and l4 clock rates incorrectly calculated.
Fixed by using proper divider clock types for the clock nodes.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-08-26 13:04:00 -07:00
Brian Norris
fc3e825fa9 ARM: brcmstb: revert SMP support
There were several issues (of varying degree of importance) pointed out
with this code late in the review cycle, yet the code was still merged.
Let's rip it out for now and look at resubmitting at a later time.

This reverts most of commit 4fbe66d990.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2014-08-25 18:46:31 -07:00
Tony Lindgren
cc824534d4 ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
Looks like MUSB cable removal can cause wake-up interrupts to
stop working for device tree based booting at least for UART3
even as nothing is dynamically remuxed. This can be fixed by
calling reconfigure_io_chain() for device tree based booting
in hwmod code. Note that we already do that for legacy booting
if the legacy mux is configured.

My guess is that this is related to UART3 and MUSB ULPI
hsusb0_data0 and hsusb0_data1 support for Carkit mode that
somehow affect the configured IO chain for UART3 and require
rearming the wake-up interrupts.

In general, for device tree based booting, pinctrl-single
calls the rearm hook that in turn calls reconfigure_io_chain
so calling reconfigure_io_chain should not be needed from the
hwmod code for other events.

So let's limit the hwmod rearming of iochain only to
HWMOD_FORCE_MSTANDBY where MUSB is currently the only user
of it. If we see other devices needing similar changes we can
add more checks for it.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-08-25 16:15:35 -07:00
Tony Lindgren
c15adae883 ARM: dts: Enable UART wake-up events for beagleboard
For device tree based booting, we need to use wake-up
interrupts like we already do for some omaps. This fixes
a PM regression on beagleboard compared to legacy booting.

Tested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-08-25 16:15:35 -07:00
Mark Brown
509a81fd20 ARM: dts: Remove twl6030 clk32g "regulator"
The kernel has never supported clk32g as a regulator since it is a clock
and not a regulator. Fortunately nothing actually references this node so
we can just remove it.

Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-08-25 16:15:34 -07:00
Markus Pargmann
9a02ae4ed4 ARM: OMAP2+: omap_device: remove warning that clk alias already exists
When an alias for a clock already exists the warning is printed. For
every module with a main_clk defined, a clk alias for fck is added.
There are some components that have the same main_clk defined, so this
is a really normal situation.

For example the am33xx edma device has 4 components using the same main
clock. So there are three warnings in the boot log for this already
existing clock alias:
	platform 49000000.edma: alias fck already exists
	platform 49000000.edma: alias fck already exists
	platform 49000000.edma: alias fck already exists

As this is only interesting for developers, this patch changes the
message to a debug message.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-08-25 16:15:34 -07:00
Hans Wennborg
6953faf976 ARM: OMAP: fix %d confusingly prefixed with 0x in format string
Fix %d confusingly prefixed with 0x in format string.

Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-08-25 16:15:34 -07:00