Commit 4b3dc9679c ("arm64: force CONFIG_SMP=y and remove redundant
and therfore can not be selected anymore.
Remove dead #ifdef-block depending on UP_LATE_INIT in
arch/arm64/kernel/setup.c
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
[will: kill do_post_cpus_up_work altogether]
Signed-off-by: Will Deacon <will.deacon@arm.com>
APQ8016 SBC board have 6 user controllable LED's.
Add following devices:
LED1 green LED triggered by system heartbeat.
LED2 green LED triggered by access to eMMC device.
LED3 green LED triggered by access to SD card.
LED4 green LED no trigger assigned.
LED5 yellow LED triggered by access to WLAN.
LED6 blue LED triggered by access to Bluetooth.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
USB2513B HUB reset line is connected to PMIC GPIO3 not GPIO1.
Fix TC7USB40MU Dual SPDT Switch select input line control, which is
connected to PMIC GPIO4 not GPIO2 and disable the pin. It is not used
for now.
Remove user LEDs definitions, because they clash with above numbers.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Hogging pins from pinctrl driver prevents client drivers
to probe.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add sdhci1 and sdhci2 device configuration nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add device nodes for SPI1, SPI2, SPI3, I2C4, SPI5, SPI6 and
BAM(DMA) engine connected to them.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Create separate file for MSM8916 pinctrl default/sleep pins state
definitions. Move in UART2 states and add SPI, I2C and SDC configurations.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
pte_valid should check if the PTE_VALID bit (1 << 0) is set in the pte,
so fix the macro definition to use bitwise & instead of logical &&.
Signed-off-by: Will Deacon <will.deacon@arm.com>
When unlocking a spinlock, we perform a read-modify-write on the owner
ticket in order to increment it and store it back with release
semantics.
In the LL/SC case, we load the 16-bit ticket using a 32-bit load and
therefore store back the wrong halfword on a big-endian system,
corrupting the lock after the first unlock and killing the system dead.
This patch fixes the unlock code to use 16-bit accessors consistently.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The flush_tlb_page() function is used on user address ranges when PTEs
(or PMDs/PUDs for huge pages) were changed (attributes or clearing). For
such cases, it is more efficient to invalidate only the last level of
the TLB with the "tlbi vale1is" instruction.
In the TLB shoot-down case, the TLB caching of the intermediate page
table levels (pmd, pud, pgd) is handled by __flush_tlb_pgtable() via the
__(pte|pmd|pud)_free_tlb() functions and it is not deferred to
tlb_finish_mmu() (as of commit 285994a62c - "arm64: Invalidate the TLB
corresponding to intermediate page table levels"). The tlb_flush()
function only needs to invalidate the TLB for the last level of page
tables; the __flush_tlb_range() function gains a fourth argument for
last level TLBI.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch moves the MAX_TLB_RANGE check into the
flush_tlb(_kernel)_range functions directly to avoid the
undescore-prefixed definitions (and for consistency with a subsequent
patch).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently create_mapping is marked with __ref, apparently because it
refers to early_alloc. However, create_mapping has no logic to prevent
erroneous use of early_alloc after it has been freed, and is only ever
called by __init functions anyway. Thus the __ref marker is misleading
and unnecessary.
Instead, this patch marks create_mapping as __init, resulting in
warnings if it is used from a a non __init functions, and allowing its
memory to be reclaimed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
lib/list_sort.c defines a 'struct debug_el', where "el" is assumedly a
a contraction of "element". This conflicts with 'enum debug_el' in our
asm/debug-monitors.h header file, where "el" stands for Exception Level.
The result is build failure when targetting allmodconfig, so rename our
enum to 'dbg_active_el' to be slightly more explicit about what it is.
Signed-off-by: Will Deacon <will.deacon@arm.com>
It is not needed after booting, this patch moves the
free_initrd_mem() function to the __init section.
This patch also make keep_initrd __initdata, to reduce kernel
size.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
At boot, the UTF-16 UEFI vendor string is copied from the system
table into a char array with a size of 100 bytes. However, this
size of 100 bytes is also used for memremapping() the source,
which may not be sufficient if the vendor string exceeds 50
UTF-16 characters, and the placement of the vendor string inside
a 4 KB page happens to leave the end unmapped.
So use the correct '100 * sizeof(efi_char16_t)' for the size of
the mapping.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: f84d02755f ("arm64: add EFI runtime services")
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
cpuid_feature_extract_field takes care of the fiddly ID register
field sign-extension, so use that instead of rolling our own version.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Rework the cpufeature detection to support ISAR0 and use that for
detecting the presence of LSE atomics.
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARMv8 CPUs do not support any of the v8.1 features, so group them
together in Kconfig to make it clear that they're part of 8.1 and not
relevant to older cores.
Signed-off-by: Will Deacon <will.deacon@arm.com>
We implement an optimised cmpxchg_local macro, so let the kernel know.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If we attempt to atomic64_dec_if_positive on INT_MIN, we will underflow
and incorrectly decide that the original parameter was positive.
This patches fixes the broken condition code so that we handle this
corner case correctly.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We don't need duplicate cmpxchg implementations, so use cmpxchg to
implement atomic{,64}_cmpxchg, like we do for xchg already.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The cost of changing a cacheline from shared to exclusive state can be
significant, especially when this is triggered by an exclusive store,
since it may result in having to retry the transaction.
This patch makes use of prfm to prefetch cachelines for write prior to
ldxr/stxr loops when using the ll/sc atomic routines.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The common (i.e. identical for ll/sc and lse) atomic macros in atomic.h
are needlessley different for atomic_t and atomic64_t.
This patch tidies up the definitions to make them consistent across the
two atomic types and factors out common code such as the add_unless
implementation based on cmpxchg.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
cmpxchg doesn't require memory barrier semantics when the value
comparison fails, so make the barrier conditional on success.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We can perform the cmpxchg comparison using eor and cbnz which avoids
the "cc" clobber for the ll/sc case and consequently for the LSE case
where we may have to fall-back on the ll/sc code at runtime.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On CPUs which support the LSE atomic instructions introduced in ARMv8.1,
it makes sense to use them in preference to ll/sc sequences.
This patch introduces runtime patching of our cmpxchg_double primitives
so that the LSE casp instruction is used instead.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On CPUs which support the LSE atomic instructions introduced in ARMv8.1,
it makes sense to use them in preference to ll/sc sequences.
This patch introduces runtime patching of our cmpxchg primitives so that
the LSE cas instruction is used instead.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On CPUs which support the LSE atomic instructions introduced in ARMv8.1,
it makes sense to use them in preference to ll/sc sequences.
This patch introduces runtime patching of our xchg primitives so that
the LSE swp instruction (yes, you read right!) is used instead.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On CPUs which support the LSE atomic instructions introduced in ARMv8.1,
it makes sense to use them in preference to ll/sc sequences.
This patch introduces runtime patching of our bitops functions so that
LSE atomic instructions are used instead.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On CPUs which support the LSE atomic instructions introduced in ARMv8.1,
it makes sense to use them in preference to ll/sc sequences.
This patch introduces runtime patching of our locking functions so that
LSE atomic instructions are used for spinlocks and rwlocks.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On CPUs which support the LSE atomic instructions introduced in ARMv8.1,
it makes sense to use them in preference to ll/sc sequences.
This patch introduces runtime patching of atomic_t and atomic64_t
routines so that the call-site for the out-of-line ll/sc sequences is
patched with an LSE atomic instruction when we detect that
the CPU supports it.
If binutils is not recent enough to assemble the LSE instructions, then
the ll/sc sequences are inlined as though CONFIG_ARM64_LSE_ATOMICS=n.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In order to patch in the new atomic instructions at runtime, we need to
generate wrappers around the out-of-line exclusive load/store atomics.
This patch adds a new Kconfig option, CONFIG_ARM64_LSE_ATOMICS. which
causes our atomic functions to branch to the out-of-line ll/sc
implementations. To avoid the register spill overhead of the PCS, the
out-of-line functions are compiled with specific compiler flags to
force out-of-line save/restore of any registers that are usually
caller-saved.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add a CPU feature for the LSE atomic instructions, so that they can be
patched in at runtime when we detect that they are supported.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARM v8.1 architecture introduces new atomic instructions to the A64
instruction set for things like cmpxchg, so advertise their availability
to userspace using a hwcap.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In preparation for the Large System Extension (LSE) atomic instructions
introduced by ARM v8.1, move the current exclusive load/store (LL/SC)
atomics into their own header file.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
cpufeature.h makes use of DECLARE_BITMAP, which in turn relies on the
BITS_TO_LONGS and DIV_ROUND_UP macros.
This patch includes kernel.h in cpufeature.h to prevent all users having
to do the same thing.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
STXR can fail for a number of reasons, so don't fail an rwlock trylock
operation simply because the STXR reported failure.
I'm not aware of any issues with the current code, but this makes it
consistent with spin_trylock and also other architectures (e.g. arch/arm).
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Implement atomic logic ops -- atomic_{or,xor,and}.
These will replace the atomic_{set,clear}_mask functions that are
available on some archs.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Implement atomic logic ops -- atomic_{or,xor,and}.
These will replace the atomic_{set,clear}_mask functions that are
available on some archs.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Our ticket-based spinlock structures rely on a definition of u16, so
include linux/types.h explicitly to ensure the thing compiles.
Found by a module build failure in -next:
arch/arm64/include/asm/spinlock_types.h:27:2: error: unknown type name 'u16'
arch/arm64/include/asm/spinlock_types.h:28:2: error: unknown type name 'u16'
arch/arm64/include/asm/spinlock_types.h:33:13: error: expected declaration specifiers or '...' before numeric constant
include/linux/spinlock_types.h:21:2: error: unknown type name 'arch_spinlock_t'
arch/arm64/include/asm/spinlock.h:34:35: error: unknown type name 'arch_spinlock_t'
arch/arm64/include/asm/spinlock.h:65:37: error: unknown type name 'arch_spinlock_t'
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The generic slowpath WARN implementation prints a backtrace, but
the report_bug() based implementation does not, opting to print the
registers instead which is generally not as useful.
Ideally, report_bug() should be fixed to make the behaviour more
consistent, but in the meantime this patch generates a backtrace
directly from the arm64 backend instead so that this functionality
is not lost with the migration to report_bug().
As a side-effect, the backtrace will be outside the oops end
marker, but that's hard to avoid without modifying generic code.
This patch can go away if report_bug() grows the ability in the
future to generate a backtrace directly or call an arch hook at the
appropriate time.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, the minimal default BUG() implementation from asm-
generic is used for arm64.
This patch uses the BRK software breakpoint instruction to generate
a trap instead, similarly to most other arches, with the generic
BUG code generating the dmesg boilerplate.
This allows bug metadata to be moved to a separate table and
reduces the amount of inline code at BUG and WARN sites. This also
avoids clobbering any registers before they can be dumped.
To mitigate the size of the bug table further, this patch makes
use of the existing infrastructure for encoding addresses within
the bug table as 32-bit offsets instead of absolute pointers.
(Note that this limits the kernel size to 2GB.)
Traps are registered at arch_initcall time for aarch64, but BUG
has minimal real dependencies and it is desirable to be able to
generate bug splats as early as possible. This patch redirects
all debug exceptions caused by BRK directly to bug_handler() until
the full debug exception support has been initialised.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
<asm/debug-monitors.h> relies on <asm/ptrace.h>, but doesn't
declare this dependency. This becomes a problem once
debug-monitors.h starts getting included all over the place to get
the BRK immedates.
The missing include of <asm/memory.h> (for UL()) in <asm/esr.h> is
also added. The series no longer relies on this, but I spotted it
during development and it may as well get fixed.
No functional change.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The way the KGDB_DYN_BRK_INS_BYTEx macros are declared is more
complex than it needs to be. Also, the macros are only used in one
place, which is arch-specific anyway.
This patch refactors the macros to simplify them, and exposes an
argument so that we can have a single macro instead of 4.
As a side effect, this patch also fixes some anomalous spellings of
"KGDB".
These changes alter the compile types of some integer constants
that are harmless but trigger truncation warnings in gcc when
assigning to 32-bit variables. This patch adds an explicit cast
for the affected cases.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It makes sense to keep all the architectural exception syndrome
definitions in the same place.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The naming of DBG_ESR_VAL_BRK is inconsistent with the way other
similar macros are named.
This patch makes the naming more consistent, and appends "64"
as a reminder that this ESR pattern only matches from AArch64
state.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
<asm/esr.h> has perfectly good constants for defining ESR values
already. Let's use them.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are only 16 comment bits in a BRK instruction, which
correspond to ESR bits 15:0. Bits 24:16 of the ESR are RES0,
and might have weird meanings in the future.
This code inserts 16 bits of comment in the ESR value instead of
20 (almost certainly a typo in the original code).
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The size of an A64 BRK instruction is the same as the size of all other
A64 instructions, because all A64 instructions are the same size.
BREAK_INSTR_SIZE is retained for readibility, but it should not be
an independent constant from AARCH64_INSN_SIZE.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A little change to patch_map() function,
use set_fixmap_offset() to make code more clear.
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When allocating memory for the kernel image, try the AllocatePages()
boot service to obtain memory at the preferred offset of
'dram_base + TEXT_OFFSET', and only revert to efi_low_alloc() if that
fails. This is the only way to allocate at the base of DRAM if DRAM
starts at 0x0, since efi_low_alloc() refuses to allocate at 0x0.
Tested-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since both CONFIG_ACPI and CONFIG_OF are enabled when booting using ACPI
tables on ARM64 platforms, we get few device tree warnings which are not
valid for ACPI boot. We can use of_have_populated_dt to check if the
device tree is populated or not before throwing out those errors.
This patch uses of_have_populated_dt to remove non legitimate device
tree warning when booting using ACPI tables.
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are cases where we want to compile out both versions of an
alternative code block, so add an enable parameter to the new conditional
alternative assembly macros in the same way as alternative_insn.
Signed-off-by: Will Deacon <will.deacon@arm.com>
'Privileged Access Never' is a new arm8.1 feature which prevents
privileged code from accessing any virtual address where read or write
access is also permitted at EL0.
This patch enables the PAN feature on all CPUs, and modifies {get,put}_user
helpers temporarily to permit access.
This will catch kernel bugs where user memory is accessed directly.
'Unprivileged loads and stores' using ldtrb et al are unaffected by PAN.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
[will: use ALTERNATIVE in asm and tidy up pan_enable check]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The system register encoding generated by sys_reg() works only
for MRS/MSR(Register) operations, as we hardcode Bit20 to 1 in
mrs_s/msr_s mask. This makes it unusable for generating instructions
accessing registers with Op0 < 2(e.g, PSTATE.x with Op0=0).
As per ARMv8 ARM, (Ref: ARMv8 ARM, Section: "System instruction class
encoding overview", C5.2, version:ARM DDI 0487A.f), the instruction
encoding reserves bits [20-19] for Op0.
This patch generalises the sys_reg, mrs_s and msr_s macros, so that
we could use them to access any of the supported system register.
Cc: James Morse <james.morse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some uses of ALTERNATIVE() may depend on a feature that is disabled at
compile time by a Kconfig option. In this case the unused alternative
instructions waste space, and if the original instruction is a nop, it
wastes time and space.
This patch adds an optional 'config' option to ALTERNATIVE() and
alternative_insn that allows the compiler to remove both the original
and alternative instructions if the config option is not defined.
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When a new cpu feature is available, the cpu feature bits will have some
initial value, which is incremented when the feature is updated.
This patch changes 'register_value' to be 'min_field_value', and checks
the feature bits value (interpreted as a signed int) is greater than this
minimum.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds an 'enable()' callback to cpu capability/feature
detection, allowing features that require some setup or configuration
to get this opportunity once the feature has been detected.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Later patches need config_sctlr_el1 to set/clear bits in the sctlr_el1
register.
This patch moves this function into header a file.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Convert the dynamic patching for ARM64_HAS_SYSREG_GIC_CPUIF over to
the newly added alternative assembler macros.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Convert the dynamic patching for ARM64_WORKAROUND_845719 over to
the newly added alternative assembler macros.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Convert the dynamic patching for ARM64_WORKAROUND_CLEAN_CACHE over to
the newly added alternative assembler macros.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The existing alternative_insn macro has some limitations that make it
hard to work with. In particular the fact it takes instructions from it
own macro arguments means it doesn't play very nicely with C pre-processor
macros because the macro arguments look like a string to the C
pre-processor. Workarounds are (probably) possible but things start to
look ugly.
Introduce an alternative set of macros that allows instructions to be
presented to the assembler as normal and switch everything over to the
new macros.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Based on arch/arm/include/asm/cputype.h, this function does the
shifting and sign extension necessary when accessing cpu feature fields.
Signed-off-by: James Morse <james.morse@arm.com>
Suggested-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Most of the cache events an architecture might support do not map well
to those provided by the ARM architecture, and as such most entries in
the event number maps are *_UNSUPPORTED. Unfortuantely as 0 is a valid
physical event identifier, the *_UNSUPPORTED macros expand to a non-zero
value and thus each unsupported event must be explicitly initialised as
such. This leads to large diffs when adding support for a new CPU, and
makes it difficult to spot the important information.
This patch follows arch/arm/ in making use of PERF_*_ALL_UNSUPPORTED
macros to initialise all entries to *_UNSUPPORTED before overriding this
for the specific events we actually support, resulting in a significant
source code reduction.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Remove paragraph about writing to the Free Software Foundation's
mailing address from GPL notice.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The default dma_common_get_sgtable() implementation relies on the CPU
address of the buffer being a regular lowmem address. This is not always
the case on arm64, since allocations from the various DMA pools may have
remapped vmalloc addresses, rendering the use of virt_to_page() invalid.
Fix this by providing our own implementation based on the fact that we
can safely derive a physical address from the DMA address in both cases.
CC: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[will: made static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Nobody seems to be producing !SMP systems anymore, so this is just
becoming a source of kernel bugs, particularly if people want to use
coherent DMA with non-shared pages.
This patch forces CONFIG_SMP=y for arm64, removing a modest amount of
code in the process.
Signed-off-by: Will Deacon <will.deacon@arm.com>
We currently bundle the callchain handling code with the PMU code,
despite the fact the two are distinct, and the former can be useful even
in the absence of the latter.
Follow the example of arch/arm and factor the callchain handling into
its own file dependent on CONFIG_PERF_EVENTS rather than
CONFIG_HW_PERF_EVENTS.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The AArch64 instruction set contains load/store pair memory accessors,
so use these in our copy_*_user routines to transfer 16 bytes per
iteration.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The compat ptrace interface allows access to the TLS register, hardware
breakpoints and watchpoints, syscall number. However, a native task
using the native ptrace interface to debug compat tasks (e.g. multi-arch
gdb) only has access to the general and VFP register sets. The compat
ptrace interface cannot be accessed from a native task.
This patch adds a new user_aarch32_ptrace_view which contains the TLS,
hardware breakpoint/watchpoint and syscall number regsets in addition to
the existing GPR and VFP regsets. This view is backwards compatible with
the previous kernels. Core dumping of 32-bit tasks and compat ptrace are
not affected since the original user_aarch32_view is preserved.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Yao Qi <yao.qi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Plumb up Makefile arguments for the already supported formats in the kbuild
system: lz4, bzip2, lzma, and lzo.
Note that just as with Image.gz, these images are not self-decompressing and
the booting firmware still needs to handle decompression before launching the
kernel image.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARMv8.1 architecture extensions introduce support for hardware
updates of the access and dirty information in page table entries. With
TCR_EL1.HA enabled, when the CPU accesses an address with the PTE_AF bit
cleared in the page table, instead of raising an access flag fault the
CPU sets the actual page table entry bit. To ensure that kernel
modifications to the page tables do not inadvertently revert a change
introduced by hardware updates, the exclusive monitor (ldxr/stxr) is
adopted in the pte accessors.
When TCR_EL1.HD is enabled, a write access to a memory location with the
DBM (Dirty Bit Management) bit set in the corresponding pte
automatically clears the read-only bit (AP[2]). Such DBM bit maps onto
the Linux PTE_WRITE bit and to check whether a writable (DBM set) page
is dirty, the kernel tests the PTE_RDONLY bit. In order to allow
read-only and dirty pages, the kernel needs to preserve the software
dirty bit. The hardware dirty status is transferred to the software
dirty bit in ptep_set_wrprotect() (using load/store exclusive loop) and
pte_modify().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 68234df4ea ("arm64: kill flush_cache_all()") removed
soft_reset() from the kernel. This was the only caller of
setup_mm_for_reboot(), so remove that also.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mark Brown reported an allnoconfig build failure in -next:
Today's linux-next fails to build an arm64 allnoconfig due to "mm:
make GUP handle pfn mapping unless FOLL_GET is requested" which
causes:
> arm64-allnoconfig
> ../mm/gup.c:51:4: error: implicit declaration of function
'update_mmu_cache' [-Werror=implicit-function-declaration]
Fix the error by moving the function to asm/pgtable.h, as is the case
for most other architectures.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since commit 9d3bfbb4df ("arm64: Combine coherent and non-coherent
swiotlb dma_ops"), __dma_common_mmap is no longer shared between two
callers, so roll it into the remaining one.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 68234df4ea ("arm64: kill flush_cache_all()") removed the
only users of these macros.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
arch_find_n_match_cpu_physical_id parses the device tree to get the
device node for a given logical cpu index. However, since ARM PMUs get
probed after the CPU device nodes are stashed while registering the
cpus, we can use of_cpu_device_node_get to avoid another DT parse.
This patch replaces arch_find_n_match_cpu_physical_id with
of_cpu_device_node_get to reuse the stashed value directly instead.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM64 pmu prints an error message in event_init() when
no hardware PMU is available. This is pretty annoying as
it keeps printing the message for every single trial, flooding
the kernel logs, unnecessarily. The return code is sufficient for
the user to figure out the reason.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This adds basic chip support for MT6795 SoC
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This is a preparatory patch for moving irq_data struct members.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 0c8c0f03e3 ("x86/fpu, sched: Dynamically allocate 'struct fpu'")
moved the thread_struct to the bottom of task_struct. As a result, the
offset is now too large to be used in an immediate add on arm64 with
some kernel configs:
arch/arm64/kernel/entry.S: Assembler messages:
arch/arm64/kernel/entry.S:588: Error: immediate out of range
arch/arm64/kernel/entry.S:597: Error: immediate out of range
This patch calculates the offset using an additional register instead of
an immediate offset.
Fixes: 0c8c0f03e3 ("x86/fpu, sched: Dynamically allocate 'struct fpu'")
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a large window (up to 64GB) for X-Gene PCIe nodes to support devices
that require huge BARs.
Each X-Gene PCIe node will now have two memory windows: a 32-bit
non-prefetchable window and a 64-bit prefetchable window.
[bhelgaas: changelog]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This includes trace points for:
kvm_arch_setup_guest_debug
kvm_arch_clear_guest_debug
I've also added some generic register setting trace events and also a
trace point to dump the array of hardware registers.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Finally advertise the KVM capability for SET_GUEST_DEBUG. Once arm
support is added this check can be moved to the common
kvm_vm_ioctl_check_extension() code.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This introduces a level of indirection for the debug registers. Instead
of using the sys_regs[] directly we store registers in a structure in
the vcpu. The new kvm_arm_reset_debug_ptr() sets the debug ptr to the
guest context.
Because we no longer give the sys_regs offset for the sys_reg_desc->reg
field, but instead the index into a debug-specific struct we need to
add a number of additional trap functions for each register. Also as the
generic generic user-space access code no longer works we have
introduced a new pair of function pointers to the sys_reg_desc structure
to override the generic code when needed.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This is a pre-cursor to sharing the code with the guest debug support.
This replaces the big macro that fishes data out of a fixed location
with a more general helper macro to restore a set of debug registers. It
uses macro substitution so it can be re-used for debug control and value
registers. It does however rely on the debug registers being 64 bit
aligned (as they happen to be in the hyp ABI).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds support for single-stepping the guest. To do this we need to
manipulate the guests PSTATE.SS and MDSCR_EL1.SS bits to trigger
stepping. We take care to preserve MDSCR_EL1 and trap access to it to
ensure we don't affect the apparent state of the guest.
As we have to enable trapping of all software debug exceptions we
suppress the ability of the guest to single-step itself. If we didn't we
would have to deal with the exception arriving while the guest was in
kernelspace when the guest is expecting to single-step userspace. This
is something we don't want to unwind in the kernel. Once the host is no
longer debugging the guest its ability to single-step userspace is
restored.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds support for SW breakpoints inserted by userspace.
We do this by trapping all guest software debug exceptions to the
hypervisor (MDCR_EL2.TDE). The exit handler sets an exit reason of
KVM_EXIT_DEBUG with the kvm_debug_exit_arch structure holding the
exception syndrome information.
It will be up to userspace to extract the PC (via GET_ONE_REG) and
determine if the debug event was for a breakpoint it inserted. If not
userspace will need to re-inject the correct exception restart the
hypervisor to deliver the debug exception to the guest.
Any other guest software debug exception (e.g. single step or HW
assisted breakpoints) will cause an error and the VM to be killed. This
is addressed by later patches which add support for the other debug
types.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This is a precursor for later patches which will need to do more to
setup debug state before entering the hyp.S switch code. The existing
functionality for setting mdcr_el2 has been moved out of hyp.S and now
uses the value kept in vcpu->arch.mdcr_el2.
As the assembler used to previously mask and preserve MDCR_EL2.HPMN I've
had to add a mechanism to save the value of mdcr_el2 as a per-cpu
variable during the initialisation code. The kernel never sets this
number so we are assuming the bootcode has set up the correct value
here.
This also moves the conditional setting of the TDA bit from the hyp code
into the C code which is currently used for the lazy debug register
context switch code.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This commit adds a stub function to support the KVM_SET_GUEST_DEBUG
ioctl. Any unsupported flag will return -EINVAL. For now, only
KVM_GUESTDBG_ENABLE is supported, although it won't have any effects.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This commit defines the API headers for guest debugging. There are two
architecture specific debug structures:
- kvm_guest_debug_arch, allows us to pass in HW debug registers
- kvm_debug_exit_arch, signals exception and possible faulting address
The type of debugging being used is controlled by the architecture
specific control bits of the kvm_guest_debug->control flags in the ioctl
structure.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This file doesn't use the clk provider APIs. Remove the include.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Commit 2ae416b142 ("mm: new mm hook framework") introduced an empty
header file (mm-arch-hooks.h) for every architecture, even those which
doesn't need to define mm hooks.
As suggested by Geert Uytterhoeven, this could be cleaned through the use
of a generic header file included via each per architecture
asm/include/Kbuild file.
The PowerPC architecture is not impacted here since this architecture has
to defined the arch_remap MM hook.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds afe (audio front end) device node to the MT8173 dtsi file.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In terms of peripherals the rk3368 is quite similar to the rk3288, which
makes it possible to have a lot basic components working in the first go.
More to follow once I tracked down all the tiny differences that still
exist in some parts.
With these dts files, the R88 board is able to boot from an attached
usb device and most likely from its emmc too, if the emmc uses a standard
partition table instead of Rockchip's own one - the emmc itself is
detected correctly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The rk3368 is Rockchip's first ARM64 soc, build around 8 Cortex-A53 cores.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Let's move out the platform Kconfig entries to a separate file, since these
changes usually get moved through arm-soc instead of the arm64 arch tree, and
this will lead to fewer conflicts
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
This patch converts the ARM64 aes-ce-ccm implementation to the
new AEAD interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Since ETMv4 driver has been merged, this patch adds ETM nodes for SC9836,
and four funnel input ports to connect with ETM output ports.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
A fairly random colletion of fixes based on -rc1 for OMAP, sunxi and
prima2 as well as a few arm64-specific DT fixes.
This series also includes a late to support a new Allwinner (sunxi)
SoC, but since it's rather simple and isolated to the
platform-specific code, it's included it for this -rc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UEUK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A fairly random colletion of fixes based on -rc1 for OMAP, sunxi and
prima2 as well as a few arm64-specific DT fixes.
This series also includes a late to support a new Allwinner (sunxi)
SoC, but since it's rather simple and isolated to the
platform-specific code, it's included it for this -rc"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: add device tree for ARM SMM-A53x2 on LogicTile Express 20MG
arm: dts: vexpress: add missing CCI PMU device node to TC2
arm: dts: vexpress: describe all PMUs in TC2 dts
GICv3: Add ITS entry to THUNDER dts
arm64: dts: Add poweroff button device node for APM X-Gene platform
ARM: dts: am4372.dtsi: disable rfbi
ARM: dts: am57xx-beagle-x15: Provide supply for usb2_phy2
ARM: dts: am4372: Add emif node
Revert "ARM: dts: am335x-boneblack: disable RTC-only sleep"
ARM: sunxi: Enable simplefb in the defconfig
ARM: Remove deprecated symbol from defconfig files
ARM: sunxi: Add Machine support for A33
ARM: sunxi: Introduce Allwinner H3 support
Documentation: sunxi: Update Allwinner SoC documentation
ARM: prima2: move to use REGMAP APIs for rtciobrg
ARM: dts: atlas7: add pinctrl and gpio descriptions
ARM: OMAP2+: Remove unnessary return statement from the void function, omap2_show_dma_caps
memory: omap-gpmc: Fix parsing of devices
We currently set x27 in compat_sys_sigreturn_wrapper and
compat_sys_rt_sigreturn_wrapper, similarly to what we do with r8/why on
32-bit ARM, in an attempt to prevent sigreturns from being restarted.
However, on arm64 we have always used pt_regs::syscallno for syscall
restarting (for both native and compat tasks), and x27 is never
inspected again before being overwritten in kernel_exit.
This patch removes the pointless register assignments.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a DTS file for the MP2 Cortex-A53 Soft Macrocell Model implemented
on a LogicTile Express 20MG (V2F-1XV7) daughterboard. This is based on
the version that's currently available from the ARM DTS repository [1].
[1] git://linux-arm.org/arm-dts.git
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The PCIe host controller uses MSIs provided by GICv3 ITS. Enable it on
Thunder SoCs by adding an entry to DT.
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This patch adds poweroff button device node to support poweroff feature
on APM X-Gene Mustang platform.
Signed-off-by: Y Vo <yvo@apm.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Currently we enable debug exceptions before reading ESR_EL1 in both
el0_inv and el1_inv. If a debug exception is taken before we read
ESR_EL1, the value will have been corrupted.
As el*_inv is typically fatal, an intervening debug exception results in
misleading debug information being logged to the console, but is not
otherwise harmful.
As with the other entry paths, we can use the ESR_EL1 value stashed
earlier in the exception entry (in x25 for el0_sync{,_compat}, and x1
for el1_sync), giving us better error reporting in this case.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For those parts of the arm64 ACPI code that need to check GICC subtables
in the MADT, use the new BAD_MADT_GICC_ENTRY macro instead of the previous
BAD_MADT_ENTRY. The new macro takes into account differences in the size
of the GICC subtable that the old macro did not; this caused failures even
though the subtable entries are valid.
Fixes: aeb823bbac ("ACPICA: ACPI 6.0: Add changes for FADT table.")
Signed-off-by: Al Stone <al.stone@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The BAD_MADT_ENTRY() macro is designed to work for all of the subtables
of the MADT. In the ACPI 5.1 version of the spec, the struct for the
GICC subtable (struct acpi_madt_generic_interrupt) is 76 bytes long; in
ACPI 6.0, the struct is 80 bytes long. But, there is only one definition
in ACPICA for this struct -- and that is the 6.0 version. Hence, when
BAD_MADT_ENTRY() compares the struct size to the length in the GICC
subtable, it fails if 5.1 structs are in use, and there are systems in
the wild that have them.
This patch adds the BAD_MADT_GICC_ENTRY() that checks the GICC subtable
only, accounting for the difference in specification versions that are
possible. The BAD_MADT_ENTRY() will continue to work as is for all other
MADT subtables.
This code is being added to an arm64 header file since that is currently
the only architecture using the GICC subtable of the MADT. As a GIC is
specific to ARM, it is also unlikely the subtable will be used elsewhere.
Fixes: aeb823bbac ("ACPICA: ACPI 6.0: Add changes for FADT table.")
Signed-off-by: Al Stone <al.stone@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
[catalin.marinas@arm.com: extra brackets around macro arguments]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The MT8173 eval board contains a MT6397 PMIC. This adds the
corresponding device node to the dts file.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Ceva ahci controller is available on the Xilinx Zynq UltraScale+
MPSoC.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[catalin.marinas@arm.com: removed unnecessary defconfig changes]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Patch 63a4aea556 ("of: clean-up unnecessary libfdt include paths")
removed all explicit libfdt include paths, since those are no longer
necessary after the latest dtc upgrade. However, this one snuck in
during the same merge window. Remove it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a DA9211 dual-channel BUCK regulator to i2c1.
This regulator supplies GPU and DVFS1 voltages.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds an idle-states node to describe the mt8173 idle states and
also adds references to the idle-states node in all CPU nodes.
Signed-off-by: Howard Chen <howard.chen@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds the SCPSYS device node to the MT8173 dtsi file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add MT8173 I2C device nodes, include I2C controllers and pins.
MT8173 has six I2C controllers, from i2c0 to i2c6, exclude i2c5.
The 6th I2C controller register base doesn't next to 5th I2C,
and there is a hardware between 5th and 6th I2C controller. So
SoC designer name 6th controller as "i2c6", not "i2c5".
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds the device node for the PMIC wrapper.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We used to use a fixed rate clock for the UARTs. Now that we have clock
support we can associate the correct clocks to the UARTs and drop the
26MHz fixed rate UART clock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds the device nodes providing clocks on the Mediatek MT8173.
These are: topckgen, infracfg, pericfg and apmixedsys. These are
fed by two oscillators also added by this patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- suspicious RCU usage warning
- BPF (out of bounds array read and endianness conversion)
- perf (of_node usage after of_node_put, cpu_pmu->plat_device
assignment)
- huge pmd/pud check for value 0
- rate-limiting should only take unhandled signals into account
Clean-up:
- incorrect use of pgprot_t type
- unused header include
- __init annotation to arm_cpuidle_init
- pr_debug instead of pr_error for disabled GICC entries in ACPI/MADT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R+XU
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes (and cleanups) from Catalin Marinas:
"Various arm64 fixes:
- suspicious RCU usage warning
- BPF (out of bounds array read and endianness conversion)
- perf (of_node usage after of_node_put, cpu_pmu->plat_device
assignment)
- huge pmd/pud check for value 0
- rate-limiting should only take unhandled signals into account
Clean-up:
- incorrect use of pgprot_t type
- unused header include
- __init annotation to arm_cpuidle_init
- pr_debug instead of pr_error for disabled GICC entries in
ACPI/MADT"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix show_unhandled_signal_ratelimited usage
ARM64 / SMP: Switch pr_err() to pr_debug() for disabled GICC entry
arm64: cpuidle: add __init section marker to arm_cpuidle_init
arm64: Don't report clear pmds and puds as huge
arm64: perf: fix unassigned cpu_pmu->plat_device when probing PMU PPIs
arm64: perf: Don't use of_node after putting it
arm64: fix incorrect use of pgprot_t variable
arm64/hw_breakpoint.c: remove unnecessary header
arm64: bpf: fix endianness conversion bugs
arm64: bpf: fix out-of-bounds read in bpf2a64_offset()
ARM64: smp: Fix suspicious RCU usage with ipi tracepoints
Commit 86dca36e6b introduced ratelimited usage for
'unhandled_signal' messages.
The commit checks the ratelimit irrespective of whether
the signal is handled or not, which is wrong and leads
to false reports like the below in dmesg :
__do_user_fault: 127 callbacks suppressed
Do the ratelimit check only if the signal is unhandled.
Fixes: 86dca36e6b ("arm64: use private ratelimit state along with show_unhandled_signals")
Cc: Vladimir Murzin <Vladimir.Murzin@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
It is normal that firmware presents GICC entry or entries (processors)
with disabled flag in ACPI MADT, taking a system of 16 cpus for example,
ACPI firmware may present 8 ebabled first with another 8 cpus disabled
in MADT, the disabled cpus can be hot-added later.
Firmware may also present more cpus than the hardware actually has, but
disabled the unused ones, and easily enable it when the hardware has such
cpus to make the firmware code scalable.
So that's not an error for disabled cpus in MADT, we can switch pr_err()
to pr_debug() to make the boot a little quieter by default.
Since hwid for disabled cpus often are invalid, and we check invalid hwid
first in the code, for use case that hot add cpus later will be filtered
out and will not be counted in possible cups, so move this check before
the hwid one to prepare the code to count for disabeld cpus when cpu
hot-plug is introduced.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVlXl/AAoJEFk3GJrT+8ZlDccQAJ5vxvImNvJmoqeCv+6Tkshm
UOGtoTBWKu+1wVgvYvYWXbNL06NKtS1c/CP8CZE0V6XdLQ+EHd4RWsHyRLHi4xwS
6qqtwVfqYwFLli++87NKqzizl01a0eImPiHl5Rwo9oFy0u81+lsivwWbCBk+Dh0n
HtkmuKzWnKSYL3rgnApq1USL4dhbc6SbNYo0pwvZXNDTK57FrQN/2Z2Pl1FZS9RQ
BQgnqDSdhvF5PD/fWJ5KHs2k2WDtjMMN2TgVMtMjMg2x5kSMAN6fBwi49wYgcwUz
ndHtuHosX4BkPgDHvzIv7jRCYHeRaHOYxbPG+tzYXci4gXUUEn3i8jte91Hb3+ri
tDcgAnod+R1SoBmSRdj/nqM7Y8Qw7Pnjo2tuKYfb1NFaX5KtjrjaaDx/09G7PD+U
fw400HKPi4r2h11n96Y5MZUbLv9XgB9BAePmIdNLuQZabFc1DcsUOG9JbRsMArRT
5g6Sk+Lar9FGH32fLk5sGEAroFs52YmGmLviHKiAsbBSOV751SN2AcA8NDXBuKI1
L+hC41NslENztHTgLsmEt6YY4H/4+jW66du5GYc4ZkPd1scO2+esXDzPZ864vxo+
rIIMnRNQHb2hGiNvImyzEt2NgelSk/xKQR5Dl6MNiKCmiyw2XHlR5UTkRRBZXDd+
5T1KnOvKE2THuxWyWARH
=bhUU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late fixes and dependencies from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Enable BRCMNAND driver
ARM: BCM: Do not select CONFIG_MTD_NAND_BRCMNAND
ARM: at91/dt: update udc compatible strings
ARM: at91/dt: trivial: fix USB udc compatible string
arm64: dts: Add APM X-Gene standby GPIO controller DTS entries
soc: qcom: spm: Fix idle on THUMB2 kernels
ARM: dove: fix legacy dove IRQ numbers
ARM: mvebu: fix suspend to RAM on big-endian configurations
ARM: mvebu: adjust Armada XP DT spi muxing after pinctrl function rename
serial: 8250_omap: Move wake-up interrupt to generic wakeirq
serial: omap: Switch wake-up interrupt to generic wakeirq
mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq
It is not needed after booting, this patch moves the arm_cpuidle_init()
function to the __init section.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Add "make xenconfig" to assist in generating configs for Xen guests.
- Preparatory cleanups necessary for supporting 64 KiB pages in ARM
guests.
- Automatically use hvc0 as the default console in ARM guests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJVkpoqAAoJEFxbo/MsZsTRu3IH/2AMPx2i65hoSqfHtGf3sz/z
XNfcidVmOElFVXGaW83m0tBWMemT5LpOGRfiq5sIo8xt/8xD2vozEkl/3kkf3RrX
EmZDw3E8vmstBdBTjWdovVhNenRc0m0pB5daS7wUdo9cETq1ag1L3BHTB3fEBApO
74V6qAfnhnq+snqWhRD3XAk3LKI0nWuWaV+5HsmxDtnunGhuRLGVs7mwxZGg56sM
mILA0eApGPdwyVVpuDe0SwV52V8E/iuVOWTcomGEN2+cRWffG5+QpHxQA8bOtF6O
KfqldiNXOY/idM+5+oSm9hespmdWbyzsFqmTYz0LvQvxE8eEZtHHB3gIcHkE8QU=
=danz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.2-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Xen features and cleanups for 4.2-rc0:
- add "make xenconfig" to assist in generating configs for Xen guests
- preparatory cleanups necessary for supporting 64 KiB pages in ARM
guests
- automatically use hvc0 as the default console in ARM guests"
* tag 'for-linus-4.2-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
block/xen-blkback: s/nr_pages/nr_segs/
block/xen-blkfront: Remove invalid comment
block/xen-blkfront: Remove unused macro MAXIMUM_OUTSTANDING_BLOCK_REQS
arm/xen: Drop duplicate define mfn_to_virt
xen/grant-table: Remove unused macro SPP
xen/xenbus: client: Fix call of virt_to_mfn in xenbus_grant_ring
xen: Include xen/page.h rather than asm/xen/page.h
kconfig: add xenconfig defconfig helper
kconfig: clarify kvmconfig is for kvm
xen/pcifront: Remove usage of struct timeval
xen/tmem: use BUILD_BUG_ON() in favor of BUG_ON()
hvc_xen: avoid uninitialized variable warning
xenbus: avoid uninitialized variable warning
xen/arm: allow console=hvc0 to be omitted for guests
arm,arm64/xen: move Xen initialization earlier
arm/xen: Correctly check if the event channel interrupt is present
The current pmd_huge() and pud_huge() functions simply check if the table
bit is not set and reports the entries as huge in that case. This is
counter-intuitive as a clear pmd/pud cannot also be a huge pmd/pud, and
it is inconsistent with at least arm and x86.
To prevent others from making the same mistake as me in looking at code
that calls these functions and to fix an issue with KVM on arm64 that
causes memory corruption due to incorrect page reference counting
resulting from this mistake, let's change the behavior.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Fixes: 084bd29810 ("ARM64: mm: HugeTLB support.")
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit d795ef9aa8 ("arm64: perf: don't warn about missing
interrupt-affinity property for PPIs") added a check for PPIs so that
we avoid parsing the interrupt-affinity property for these naturally
affine interrupts.
Unfortunately, this check can trigger an early (successful) return and
we will not assign the value of cpu_pmu->plat_device. This patch fixes
the issue.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It's possible, albeit unlikely, that using the of_node here will
reference freed memory. Call of_node_put() after printing the
name to be safe.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This fixes a build failure under STRICT_MM_TYPECHECKS, by adding
a missing pgprot_val() around a pgport_t reference.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
4 drivers / enabling modules:
NFIT:
Instantiates an "nvdimm bus" with the core and registers memory devices
(NVDIMMs) enumerated by the ACPI 6.0 NFIT (NVDIMM Firmware Interface
table). After registering NVDIMMs the NFIT driver then registers
"region" devices. A libnvdimm-region defines an access mode and the
boundaries of persistent memory media. A region may span multiple
NVDIMMs that are interleaved by the hardware memory controller. In
turn, a libnvdimm-region can be carved into a "namespace" device and
bound to the PMEM or BLK driver which will attach a Linux block device
(disk) interface to the memory.
PMEM:
Initially merged in v4.1 this driver for contiguous spans of persistent
memory address ranges is re-worked to drive PMEM-namespaces emitted by
the libnvdimm-core. In this update the PMEM driver, on x86, gains the
ability to assert that writes to persistent memory have been flushed all
the way through the caches and buffers in the platform to persistent
media. See memcpy_to_pmem() and wmb_pmem().
BLK:
This new driver enables access to persistent memory media through "Block
Data Windows" as defined by the NFIT. The primary difference of this
driver to PMEM is that only a small window of persistent memory is
mapped into system address space at any given point in time. Per-NVDIMM
windows are reprogrammed at run time, per-I/O, to access different
portions of the media. BLK-mode, by definition, does not support DAX.
BTT:
This is a library, optionally consumed by either PMEM or BLK, that
converts a byte-accessible namespace into a disk with atomic sector
update semantics (prevents sector tearing on crash or power loss). The
sinister aspect of sector tearing is that most applications do not know
they have a atomic sector dependency. At least today's disk's rarely
ever tear sectors and if they do one almost certainly gets a CRC error
on access. NVDIMMs will always tear and always silently. Until an
application is audited to be robust in the presence of sector-tearing
the usage of BTT is recommended.
Thanks to: Ross Zwisler, Jeff Moyer, Vishal Verma, Christoph Hellwig,
Ingo Molnar, Neil Brown, Boaz Harrosh, Robert Elliott, Matthew Wilcox,
Andy Rudoff, Linda Knippers, Toshi Kani, Nicholas Moulin, Rafael
Wysocki, and Bob Moore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VtWG
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm
Pull libnvdimm subsystem from Dan Williams:
"The libnvdimm sub-system introduces, in addition to the
libnvdimm-core, 4 drivers / enabling modules:
NFIT:
Instantiates an "nvdimm bus" with the core and registers memory
devices (NVDIMMs) enumerated by the ACPI 6.0 NFIT (NVDIMM Firmware
Interface table).
After registering NVDIMMs the NFIT driver then registers "region"
devices. A libnvdimm-region defines an access mode and the
boundaries of persistent memory media. A region may span multiple
NVDIMMs that are interleaved by the hardware memory controller. In
turn, a libnvdimm-region can be carved into a "namespace" device and
bound to the PMEM or BLK driver which will attach a Linux block
device (disk) interface to the memory.
PMEM:
Initially merged in v4.1 this driver for contiguous spans of
persistent memory address ranges is re-worked to drive
PMEM-namespaces emitted by the libnvdimm-core.
In this update the PMEM driver, on x86, gains the ability to assert
that writes to persistent memory have been flushed all the way
through the caches and buffers in the platform to persistent media.
See memcpy_to_pmem() and wmb_pmem().
BLK:
This new driver enables access to persistent memory media through
"Block Data Windows" as defined by the NFIT. The primary difference
of this driver to PMEM is that only a small window of persistent
memory is mapped into system address space at any given point in
time.
Per-NVDIMM windows are reprogrammed at run time, per-I/O, to access
different portions of the media. BLK-mode, by definition, does not
support DAX.
BTT:
This is a library, optionally consumed by either PMEM or BLK, that
converts a byte-accessible namespace into a disk with atomic sector
update semantics (prevents sector tearing on crash or power loss).
The sinister aspect of sector tearing is that most applications do
not know they have a atomic sector dependency. At least today's
disk's rarely ever tear sectors and if they do one almost certainly
gets a CRC error on access. NVDIMMs will always tear and always
silently. Until an application is audited to be robust in the
presence of sector-tearing the usage of BTT is recommended.
Thanks to: Ross Zwisler, Jeff Moyer, Vishal Verma, Christoph Hellwig,
Ingo Molnar, Neil Brown, Boaz Harrosh, Robert Elliott, Matthew Wilcox,
Andy Rudoff, Linda Knippers, Toshi Kani, Nicholas Moulin, Rafael
Wysocki, and Bob Moore"
* tag 'libnvdimm-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm: (33 commits)
arch, x86: pmem api for ensuring durability of persistent memory updates
libnvdimm: Add sysfs numa_node to NVDIMM devices
libnvdimm: Set numa_node to NVDIMM devices
acpi: Add acpi_map_pxm_to_online_node()
libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only
pmem: flag pmem block devices as non-rotational
libnvdimm: enable iostat
pmem: make_request cleanups
libnvdimm, pmem: fix up max_hw_sectors
libnvdimm, blk: add support for blk integrity
libnvdimm, btt: add support for blk integrity
fs/block_dev.c: skip rw_page if bdev has integrity
libnvdimm: Non-Volatile Devices
tools/testing/nvdimm: libnvdimm unit test infrastructure
libnvdimm, nfit, nd_blk: driver for BLK-mode access persistent memory
nd_btt: atomic sector updates
libnvdimm: infrastructure for btt devices
libnvdimm: write blk label set
libnvdimm: write pmem label set
libnvdimm: blk labels and namespace instantiation
...
We keep collecting defconfig updates in a separate branch mostly to encourage
people to handle them separately and avoid conflicts between different topics.
Most of these are enablement of new SoCs, boards or drivers that have
come in, or minor config refreshes due to reorderings in Kconfig
files, etc. I.e. mostly minor churn of various kinds.
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q6ks
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Kevin Hilman:
"We keep collecting defconfig updates in a separate branch mostly to
encourage people to handle them separately and avoid conflicts between
different topics.
Most of these are enablement of new SoCs, boards or drivers that have
come in, or minor config refreshes due to reorderings in Kconfig
files, etc. I.e. mostly minor churn of various kinds"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: multi_v7_defconfig: remove duplicate CONFIG_COMMON_CLK_QCOM=y
ARM: multi_v7_defconfig: Enable display on Trats2 board
ARM64: add GPIO keys to the defconfig
ARM: keystone: defconfig: enable netcp driver by default
ARM: exynos_defconfig: Enable CONFIG_SENSORS_INA2XX for Odroid-XU3
ARM: exynos_defconfig: Enable CONFIG_SENSORS_PWM_FAN for Odroid-XU3
ARM: omap2plus_defconfig: Enable TOUCHSCREEN_PIXCIR
ARM: omap2plus_defconfig: Add dm816x USB PHY as a loadable module
ARM: omap2plus_defconifg: Enable DM9000 in omap2plus_defconfig
ARM: lpc18xx: remove DEBUG_LL_UART_8250 from defconfig
ARM: multi_v7_defconfig: Make media support modular
ARM: multi_v7_defconfig: Make sound support modular
ARM: multi_v7_defconfig: Enable shmobile r8a7778/bockw platform
ARM: exynos_defconfig: savedefconfig
ARM: exynos_defconfig: Enable display on Trats2 board
ARM: multi_v7_defconfig: Enable OHCI on exynos SoCs
ARM: multi_v7_defconfig: Enable TMU for exynos SoCs
ARM: multi_v7_defconfig: Enable PMIC and MUIC drivers for exynos
ARM: multi_v7_defconfig: Enable CPU idle for exynos SoCs
ARM: multi_v7_defconfig: Enable Cypress APA I2C Trackpad support
...
Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses
Conflicts:
arch/arm64/boot/dts/arm/juno-motherboard.dtsi
Trivial add/add conflict with our dt branch.
Resolution: take both sides.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=02Gm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Kevin Hilman:
"Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: soc: sunxi: Introduce SoC driver to map SRAMs
arm-cci: Add aliases for PMU events
arm-cci: Add CCI-500 PMU support
arm-cci: Sanitise CCI400 PMU driver specific code
arm-cci: Abstract handling for CCI events
arm-cci: Abstract out the PMU counter details
arm-cci: Cleanup PMU driver code
arm-cci: Do not enable CCI-400 PMU by default
firmware: qcom: scm: Add HDCP Support
ARM: berlin: add an ADC node for the BG2Q
ARM: berlin: remove useless chip and system ctrl compatibles
clk: berlin: drop direct of_iomap of nodes reg property
ARM: berlin: move BG2Q clock node
ARM: berlin: move BG2CD clock node
ARM: berlin: move BG2 clock node
clk: berlin: prepare simple-mfd conversion
pinctrl: berlin: drop SoC stub provided regmap
ARM: berlin: move pinctrl to simple-mfd nodes
pinctrl: berlin: prepare to use regmap provided by syscon
reset: berlin: drop arch_initcall initialization
...
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wWIc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Kevin Hilman:
"As usual, quite a few device-tree updates in ARM land. There was one
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
ARM: hisi: revert changes from hisi/hip04-dt branch
ARM: nomadik: set proper compatible for accelerometer
ARM64: juno: add GPIO keys
ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
ARM: dts: Introduce STM32F429 MCU
ARM: socfpga: dts: enable ethernet for Arria10 devkit
ARM: dts: k2l: fix the netcp range size
ARM: dts: k2e: fix the netcp range size
ARM: dts: k2hk: fix the netcp range size
ARM: dts: k2l-evm: Add device bindings for netcp driver
ARM: dts: k2e-evm: Add device bindings for netcp driver
ARM: dts: k2hk-evm: Add device bindings for netcp driver
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
arm64: dts: Add dts files for Hisilicon Hi6220 SoC
clk: hi6220: Document devicetree bindings for hi6220 clock
arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
...
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZtPK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform support updates from Kevin Hilman:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
ARM: socfpga: fix build error due to secondary_startup
MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
ARM: ep93xx: simone: support for SPI-based MMC/SD cards
MAINTAINERS: update Shawn's email to use kernel.org one
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
...
A relatively small setup of cleanups this time around, and similar to last time
the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0zof
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Kevin Hilman:
"A relatively small setup of cleanups this time around, and similar to
last time the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: fix EFM32 build breakage caused by cpu_resume_arm
ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
ARM: v7 setup function should invalidate L1 cache
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
ARM: ux500: delete static resource defines
ARM: ux500: rename ux500_map_io
ARM: ux500: look up PRCMU resource from DT
ARM: ux500: kill off L2CC static map
...
Merge second patchbomb from Andrew Morton:
- most of the rest of MM
- lots of misc things
- procfs updates
- printk feature work
- updates to get_maintainer, MAINTAINERS, checkpatch
- lib/ updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (96 commits)
exit,stats: /* obey this comment */
coredump: add __printf attribute to cn_*printf functions
coredump: use from_kuid/kgid when formatting corename
fs/reiserfs: remove unneeded cast
NILFS2: support NFSv2 export
fs/befs/btree.c: remove unneeded initializations
fs/minix: remove unneeded cast
init/do_mounts.c: add create_dev() failure log
kasan: remove duplicate definition of the macro KASAN_FREE_PAGE
fs/efs: femove unneeded cast
checkpatch: emit "NOTE: <types>" message only once after multiple files
checkpatch: emit an error when there's a diff in a changelog
checkpatch: validate MODULE_LICENSE content
checkpatch: add multi-line handling for PREFER_ETHER_ADDR_COPY
checkpatch: suggest using eth_zero_addr() and eth_broadcast_addr()
checkpatch: fix processing of MEMSET issues
checkpatch: suggest using ether_addr_equal*()
checkpatch: avoid NOT_UNIFIED_DIFF errors on cover-letter.patch files
checkpatch: remove local from codespell path
checkpatch: add --showfile to allow input via pipe to show filenames
...
Upper bits should be zeroed in endianness conversion:
- even when there's no need to change endianness (i.e., BPF_FROM_BE
on big endian or BPF_FROM_LE on little endian);
- after rev16.
This patch fixes such bugs by emitting extra instructions to clear
upper bits.
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Fixes: e54bcde3d6 ("arm64: eBPF JIT compiler")
Cc: <stable@vger.kernel.org> # 3.18+
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Nobody used these hooks so they were removed from common code, and can now
be removed from the architectures.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull asm/scatterlist.h removal from Jens Axboe:
"We don't have any specific arch scatterlist anymore, since parisc
finally switched over. Kill the include"
* 'for-4.2/sg' of git://git.kernel.dk/linux-block:
remove scatterlist.h generation from arch Kbuild files
remove <asm/scatterlist.h>
Problems occur when bpf_to or bpf_from has value prog->len - 1 (e.g.,
"Very long jump backwards" in test_bpf where the last instruction is a
jump): since ctx->offset has length prog->len, ctx->offset[bpf_to + 1]
or ctx->offset[bpf_from + 1] will cause an out-of-bounds read, leading
to a bogus jump offset and kernel panic.
This patch moves updating ctx->offset to after calling build_insn(),
and changes indexing to use bpf_to and bpf_from without + 1.
Fixes: e54bcde3d6 ("arm64: eBPF JIT compiler")
Cc: <stable@vger.kernel.org> # 3.18+
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
John Stultz reported an RCU splat on ARM with ipi trace events
enabled. It looks like the same problem exists on ARM64.
At this point in the IPI handling path we haven't called
irq_enter() yet, so RCU doesn't know that we're about to exit
idle and properly warns that we're using RCU from an idle CPU.
Use trace_ipi_entry_rcuidle() instead of trace_ipi_entry() so
that RCU is informed about our exit from idle.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # 3.17+
Fixes: 45ed695ac1 ("ARM64: add IPI tracepoints")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We keep collecting defconfig updates in a separate branch mostly to encourage
people to handle them separately and avoid conflicts between different topics.
Most of these are enablement of new SoCs, boards or drivers that have
come in, or minor config refreshes due to reorderings in Kconfig
files, etc. I.e. mostly minor churn of various kinds.
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q6ks
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' into test-merge
ARM: SoC: defconfig updates for v4.2
We keep collecting defconfig updates in a separate branch mostly to encourage
people to handle them separately and avoid conflicts between different topics.
Most of these are enablement of new SoCs, boards or drivers that have
come in, or minor config refreshes due to reorderings in Kconfig
files, etc. I.e. mostly minor churn of various kinds.
Conflicts: None
# gpg: Signature made Wed Jun 24 21:32:27 2015 PDT using RSA key ID D3FBC665
# gpg: Good signature from "Kevin Hilman <khilman@deeprootsystems.com>"
# gpg: aka "Kevin Hilman <khilman@linaro.org>"
# gpg: aka "Kevin Hilman <khilman@kernel.org>"
Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses
Conflicts:
arch/arm64/boot/dts/arm/juno-motherboard.dtsi
Trivial add/add conflict with our dt branch.
Resolution: take both sides.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=02Gm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' into test-merge
ARM: SoC: driver updates for v4.2
Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses
Conflicts:
arch/arm64/boot/dts/arm/juno-motherboard.dtsi
Trivial add/add conflict with our dt branch.
Resolution: take both sides.
# gpg: Signature made Wed Jun 24 21:32:17 2015 PDT using RSA key ID D3FBC665
# gpg: Good signature from "Kevin Hilman <khilman@deeprootsystems.com>"
# gpg: aka "Kevin Hilman <khilman@linaro.org>"
# gpg: aka "Kevin Hilman <khilman@kernel.org>"
# Conflicts:
# arch/arm64/boot/dts/arm/juno-motherboard.dtsi
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wWIc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' into test-merge
ARM: SoC: DT updates for v4.2
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
# gpg: Signature made Wed Jun 24 21:32:14 2015 PDT using RSA key ID D3FBC665
# gpg: Good signature from "Kevin Hilman <khilman@deeprootsystems.com>"
# gpg: aka "Kevin Hilman <khilman@linaro.org>"
# gpg: aka "Kevin Hilman <khilman@kernel.org>"
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZtPK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' into test-merge
ARM: SoC: platform support for v4.2
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
# gpg: Signature made Wed Jun 24 21:32:12 2015 PDT using RSA key ID D3FBC665
# gpg: Good signature from "Kevin Hilman <khilman@deeprootsystems.com>"
# gpg: aka "Kevin Hilman <khilman@linaro.org>"
# gpg: aka "Kevin Hilman <khilman@kernel.org>"
# Conflicts:
# arch/arm/mach-socfpga/core.h
A relatively small setup of cleanups this time around, and similar to last time
the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0zof
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' into test-merge
ARM: SoC cleanups for v4.2
A relatively small setup of cleanups this time around, and similar to last time
the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files
Conflicts: None
# gpg: Signature made Wed Jun 24 21:32:09 2015 PDT using RSA key ID D3FBC665
# gpg: Good signature from "Kevin Hilman <khilman@deeprootsystems.com>"
# gpg: aka "Kevin Hilman <khilman@linaro.org>"
# gpg: aka "Kevin Hilman <khilman@kernel.org>"
Merge first patchbomb from Andrew Morton:
- a few misc things
- ocfs2 udpates
- kernel/watchdog.c feature work (took ages to get right)
- most of MM. A few tricky bits are held up and probably won't make 4.2.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (91 commits)
mm: kmemleak_alloc_percpu() should follow the gfp from per_alloc()
mm, thp: respect MPOL_PREFERRED policy with non-local node
tmpfs: truncate prealloc blocks past i_size
mm/memory hotplug: print the last vmemmap region at the end of hot add memory
mm/mmap.c: optimization of do_mmap_pgoff function
mm: kmemleak: optimise kmemleak_lock acquiring during kmemleak_scan
mm: kmemleak: avoid deadlock on the kmemleak object insertion error path
mm: kmemleak: do not acquire scan_mutex in kmemleak_do_cleanup()
mm: kmemleak: fix delete_object_*() race when called on the same memory block
mm: kmemleak: allow safe memory scanning during kmemleak disabling
memcg: convert mem_cgroup->under_oom from atomic_t to int
memcg: remove unused mem_cgroup->oom_wakeups
frontswap: allow multiple backends
x86, mirror: x86 enabling - find mirrored memory ranges
mm/memblock: allocate boot time data structures from mirrored memory
mm/memblock: add extra "flags" to memblock to allow selection of memory based on attribute
mm: do not ignore mapping_gfp_mask in page cache allocation paths
mm/cma.c: fix typos in comments
mm/oom_kill.c: print points as unsigned int
mm/hugetlb: handle races in alloc_huge_page and hugetlb_reserve_pages
...
* New APM X-Gene SoC EDAC driver (Loc Ho)
* AMD error injection module improvements (Aravind Gopalakrishnan)
* Altera Arria 10 support (Thor Thayer)
* misc fixes and cleanups all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Id4f
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
- New APM X-Gene SoC EDAC driver (Loc Ho)
- AMD error injection module improvements (Aravind Gopalakrishnan)
- Altera Arria 10 support (Thor Thayer)
- misc fixes and cleanups all over the place
* tag 'edac_for_4.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (28 commits)
EDAC: Update Documentation/edac.txt
EDAC: Fix typos in Documentation/edac.txt
EDAC, mce_amd_inj: Set MISCV on injection
EDAC, mce_amd_inj: Move bit preparations before the injection
EDAC, mce_amd_inj: Cleanup and simplify README
EDAC, altera: Do not allow suspend when EDAC is enabled
EDAC, mce_amd_inj: Make inj_type static
arm: socfpga: dts: Add Arria10 SDRAM EDAC DTS support
EDAC, altera: Add Arria10 EDAC support
EDAC, altera: Refactor for Altera CycloneV SoC
EDAC, altera: Generalize driver to use DT Memory size
EDAC, mce_amd_inj: Add README file
EDAC, mce_amd_inj: Add individual permissions field to dfs_node
EDAC, mce_amd_inj: Modify flags attribute to use string arguments
EDAC, mce_amd_inj: Read out number of MCE banks from the hardware
EDAC, mce_amd_inj: Use MCE_INJECT_GET macro for bank node too
EDAC, xgene: Fix cpuid abuse
EDAC, mpc85xx: Extend error address to 64 bit
EDAC, mpc8xxx: Adapt for FSL SoC
EDAC, edac_stub: Drop arch-specific include
...
Currently we have many duplicates in definitions of
hugetlb_prefault_arch_hook. In all architectures this function is empty.
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CRIU is recreating the process memory layout by remapping the checkpointee
memory area on top of the current process (criu). This includes remapping
the vDSO to the place it has at checkpoint time.
However some architectures like powerpc are keeping a reference to the
vDSO base address to build the signal return stack frame by calling the
vDSO sigreturn service. So once the vDSO has been moved, this reference
is no more valid and the signal frame built later are not usable.
This patch serie is introducing a new mm hook framework, and a new
arch_remap hook which is called when mremap is done and the mm lock still
hold. The next patch is adding the vDSO remap and unmap tracking to the
powerpc architecture.
This patch (of 3):
This patch introduces a new set of header file to manage mm hooks:
- per architecture empty header file (arch/x/include/asm/mm-arch-hooks.h)
- a generic header (include/linux/mm-arch-hooks.h)
The architecture which need to overwrite a hook as to redefine it in its
header file, while architecture which doesn't need have nothing to do.
The default hooks are defined in the generic header and are used in the
case the architecture is not defining it.
In a next step, mm hooks defined in include/asm-generic/mm_hooks.h should
be moved here.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have many duplicates in definitions of huge_pmd_unshare. In
all architectures this function just returns 0 when
CONFIG_ARCH_WANT_HUGE_PMD_SHARE is N.
This patch puts the default implementation in mm/hugetlb.c and lets these
architectures use the common code.
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Rientjes <rientjes@google.com>
Cc: James Yang <James.Yang@freescale.com>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- CPU ops and PSCI (Power State Coordination Interface) refactoring
following the merging of the arm64 ACPI support, together with
handling of Trusted (secure) OS instances
- Using fixmap for permanent FDT mapping, removing the initial dtb
placement requirements (within 512MB from the start of the kernel
image). This required moving the FDT self reservation out of the
memreserve processing
- Idmap (1:1 mapping used for MMU on/off) handling clean-up
- Removing flush_cache_all() - not safe on ARM unless the MMU is off.
Last stages of CPU power down/up are handled by firmware already
- "Alternatives" (run-time code patching) refactoring and support for
immediate branch patching, GICv3 CPU interface access
- User faults handling clean-up
And some fixes:
- Fix for VDSO building with broken ELF toolchains
- Fixing another case of init_mm.pgd usage for user mappings (during
ASID roll-over broadcasting)
- Fix for FPSIMD reloading after CPU hotplug
- Fix for missing syscall trace exit
- Workaround for .inst asm bug
- Compat fix for switching the user tls tpidr_el0 register
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YeGl
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Mostly refactoring/clean-up:
- CPU ops and PSCI (Power State Coordination Interface) refactoring
following the merging of the arm64 ACPI support, together with
handling of Trusted (secure) OS instances
- Using fixmap for permanent FDT mapping, removing the initial dtb
placement requirements (within 512MB from the start of the kernel
image). This required moving the FDT self reservation out of the
memreserve processing
- Idmap (1:1 mapping used for MMU on/off) handling clean-up
- Removing flush_cache_all() - not safe on ARM unless the MMU is off.
Last stages of CPU power down/up are handled by firmware already
- "Alternatives" (run-time code patching) refactoring and support for
immediate branch patching, GICv3 CPU interface access
- User faults handling clean-up
And some fixes:
- Fix for VDSO building with broken ELF toolchains
- Fix another case of init_mm.pgd usage for user mappings (during
ASID roll-over broadcasting)
- Fix for FPSIMD reloading after CPU hotplug
- Fix for missing syscall trace exit
- Workaround for .inst asm bug
- Compat fix for switching the user tls tpidr_el0 register"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (42 commits)
arm64: use private ratelimit state along with show_unhandled_signals
arm64: show unhandled SP/PC alignment faults
arm64: vdso: work-around broken ELF toolchains in Makefile
arm64: kernel: rename __cpu_suspend to keep it aligned with arm
arm64: compat: print compat_sp instead of sp
arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP
arm64: entry: fix context tracking for el0_sp_pc
arm64: defconfig: enable memtest
arm64: mm: remove reference to tlb.S from comment block
arm64: Do not attempt to use init_mm in reset_context()
arm64: KVM: Switch vgic save/restore to alternative_insn
arm64: alternative: Introduce feature for GICv3 CPU interface
arm64: psci: fix !CONFIG_HOTPLUG_CPU build warning
arm64: fix bug for reloading FPSIMD state after CPU hotplug.
arm64: kernel thread don't need to save fpsimd context.
arm64: fix missing syscall trace exit
arm64: alternative: Work around .inst assembler bugs
arm64: alternative: Merge alternative-asm.h into alternative.h
arm64: alternative: Allow immediate branch as alternative instruction
arm64: Rework alternate sequence for ARM erratum 845719
...
for silicon that no one owns: these are really new features for
everyone.
* ARM: several features are in progress but missed the 4.2 deadline.
So here is just a smattering of bug fixes, plus enabling the VFIO
integration.
* s390: Some fixes/refactorings/optimizations, plus support for
2GB pages.
* x86: 1) host and guest support for marking kvmclock as a stable
scheduler clock. 2) support for write combining. 3) support for
system management mode, needed for secure boot in guests. 4) a bunch
of cleanups required for 2+3. 5) support for virtualized performance
counters on AMD; 6) legacy PCI device assignment is deprecated and
defaults to "n" in Kconfig; VFIO replaces it. On top of this there are
also bug fixes and eager FPU context loading for FPU-heavy guests.
* Common code: Support for multiple address spaces; for now it is
used only for x86 SMM but the s390 folks also have plans.
There are some x86 conflicts, one with the rc8 pull request and
the rest with Ingo's FPU rework.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJViYzhAAoJEL/70l94x66Dda0H/1IepMbfEy+o849d5G71fNTs
F8Y8qUP2GZuL7T53FyFUGSBw+AX7kimu9ia4gR/PmDK+QYsdosYeEjwlsolZfTBf
sHuzNtPoJhi5o1o/ur4NGameo0WjGK8f1xyzr+U8z74QDQyQv/QYCdK/4isp4BJL
ugHNHkuROX6Zng4i7jc9rfaSRg29I3GBxQUYpMkEnD3eMYMUBWGm6Rs8pHgGAMvL
vqzntgW00WNxehTqcAkmD/Wv+txxhkvIadZnjgaxH49e9JeXeBKTIR5vtb7Hns3s
SuapZUyw+c95DIipXq4EznxxaOrjbebOeFgLCJo8+XMXZum8RZf/ob24KroYad0=
=YsAR
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull first batch of KVM updates from Paolo Bonzini:
"The bulk of the changes here is for x86. And for once it's not for
silicon that no one owns: these are really new features for everyone.
Details:
- ARM:
several features are in progress but missed the 4.2 deadline.
So here is just a smattering of bug fixes, plus enabling the
VFIO integration.
- s390:
Some fixes/refactorings/optimizations, plus support for 2GB
pages.
- x86:
* host and guest support for marking kvmclock as a stable
scheduler clock.
* support for write combining.
* support for system management mode, needed for secure boot in
guests.
* a bunch of cleanups required for the above
* support for virtualized performance counters on AMD
* legacy PCI device assignment is deprecated and defaults to "n"
in Kconfig; VFIO replaces it
On top of this there are also bug fixes and eager FPU context
loading for FPU-heavy guests.
- Common code:
Support for multiple address spaces; for now it is used only for
x86 SMM but the s390 folks also have plans"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
KVM: s390: clear floating interrupt bitmap and parameters
KVM: x86/vPMU: Enable PMU handling for AMD PERFCTRn and EVNTSELn MSRs
KVM: x86/vPMU: Implement AMD vPMU code for KVM
KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch
KVM: x86/vPMU: introduce kvm_pmu_msr_idx_to_pmc
KVM: x86/vPMU: reorder PMU functions
KVM: x86/vPMU: whitespace and stylistic adjustments in PMU code
KVM: x86/vPMU: use the new macros to go between PMC, PMU and VCPU
KVM: x86/vPMU: introduce pmu.h header
KVM: x86/vPMU: rename a few PMU functions
KVM: MTRR: do not map huge page for non-consistent range
KVM: MTRR: simplify kvm_mtrr_get_guest_memory_type
KVM: MTRR: introduce mtrr_for_each_mem_type
KVM: MTRR: introduce fixed_mtrr_addr_* functions
KVM: MTRR: sort variable MTRRs
KVM: MTRR: introduce var_mtrr_range
KVM: MTRR: introduce fixed_mtrr_segment table
KVM: MTRR: improve kvm_mtrr_get_guest_memory_type
KVM: MTRR: do not split 64 bits MSR content
KVM: MTRR: clean up mtrr default type
...
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
Pull scheduler updates from Ingo Molnar:
"The main changes are:
- lockless wakeup support for futexes and IPC message queues
(Davidlohr Bueso, Peter Zijlstra)
- Replace spinlocks with atomics in thread_group_cputimer(), to
improve scalability (Jason Low)
- NUMA balancing improvements (Rik van Riel)
- SCHED_DEADLINE improvements (Wanpeng Li)
- clean up and reorganize preemption helpers (Frederic Weisbecker)
- decouple page fault disabling machinery from the preemption
counter, to improve debuggability and robustness (David
Hildenbrand)
- SCHED_DEADLINE documentation updates (Luca Abeni)
- topology CPU masks cleanups (Bartosz Golaszewski)
- /proc/sched_debug improvements (Srikar Dronamraju)"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
sched/deadline: Remove needless parameter in dl_runtime_exceeded()
sched: Remove superfluous resetting of the p->dl_throttled flag
sched/deadline: Drop duplicate init_sched_dl_class() declaration
sched/deadline: Reduce rq lock contention by eliminating locking of non-feasible target
sched/deadline: Make init_sched_dl_class() __init
sched/deadline: Optimize pull_dl_task()
sched/preempt: Add static_key() to preempt_notifiers
sched/preempt: Fix preempt notifiers documentation about hlist_del() within unsafe iteration
sched/stop_machine: Fix deadlock between multiple stop_two_cpus()
sched/debug: Add sum_sleep_runtime to /proc/<pid>/sched
sched/debug: Replace vruntime with wait_sum in /proc/sched_debug
sched/debug: Properly format runnable tasks in /proc/sched_debug
sched/numa: Only consider less busy nodes as numa balancing destinations
Revert 095bebf61a ("sched/numa: Do not move past the balance point if unbalanced")
sched/fair: Prevent throttling in early pick_next_task_fair()
preempt: Reorganize the notrace definitions a bit
preempt: Use preempt_schedule_context() as the official tracing preemption point
sched: Make preempt_schedule_context() function-tracing safe
x86: Remove cpu_sibling_mask() and cpu_core_mask()
x86: Replace cpu_**_mask() with topology_**_cpumask()
...
Pull locking updates from Ingo Molnar:
"The main changes are:
- 'qspinlock' support, enabled on x86: queued spinlocks - these are
now the spinlock variant used by x86 as they outperform ticket
spinlocks in every category. (Waiman Long)
- 'pvqspinlock' support on x86: paravirtualized variant of queued
spinlocks. (Waiman Long, Peter Zijlstra)
- 'qrwlock' support, enabled on x86: queued rwlocks. Similar to
queued spinlocks, they are now the variant used by x86:
CONFIG_ARCH_USE_QUEUED_SPINLOCKS=y
CONFIG_QUEUED_SPINLOCKS=y
CONFIG_ARCH_USE_QUEUED_RWLOCKS=y
CONFIG_QUEUED_RWLOCKS=y
- various lockdep fixlets
- various locking primitives cleanups, further WRITE_ONCE()
propagation"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
locking/lockdep: Remove hard coded array size dependency
locking/qrwlock: Don't contend with readers when setting _QW_WAITING
lockdep: Do not break user-visible string
locking/arch: Rename set_mb() to smp_store_mb()
locking/arch: Add WRITE_ONCE() to set_mb()
rtmutex: Warn if trylock is called from hard/softirq context
arch: Remove __ARCH_HAVE_CMPXCHG
locking/rtmutex: Drop usage of __HAVE_ARCH_CMPXCHG
locking/qrwlock: Rename QUEUE_RWLOCK to QUEUED_RWLOCKS
locking/pvqspinlock: Rename QUEUED_SPINLOCK to QUEUED_SPINLOCKS
locking/pvqspinlock: Replace xchg() by the more descriptive set_mb()
locking/pvqspinlock, x86: Enable PV qspinlock for Xen
locking/pvqspinlock, x86: Enable PV qspinlock for KVM
locking/pvqspinlock, x86: Implement the paravirt qspinlock call patching
locking/pvqspinlock: Implement simple paravirt support for the qspinlock
locking/qspinlock: Revert to test-and-set on hypervisors
locking/qspinlock: Use a simple write to grab the lock
locking/qspinlock: Optimize for smaller NR_CPUS
locking/qspinlock: Extract out code snippets for the next patch
locking/qspinlock: Add pending bit
...
printk_ratelimit() shares the ratelimiting state with other callers what
may lead to scenarios where at the time we want to print out debug
information we already limited, so nothing appears in the dmesg - this
makes exception-trace quite poor helper in debugging.
Additionally, we have imbalance with some messages limited with global
ratelimit state and other messages limited with their private state
defined via pr_*_ratelimited().
To address this inconsistency show_unhandled_signals_ratelimited()
macro is introduced and caller sites are converted to use it.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Report unhandled SP/PC alignment faults if the show_unhandled_signals
variable is set (via /proc/sys/debug/exception-trace).
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Merge the mvebu/drivers branch of the arm-soc tree which contains
just a single patch bfa1ce5f38 ("bus:
mvebu-mbus: add mv_mbus_dram_info_nooverlap()") that happens to be
a prerequisite of the new marvell/cesa crypto driver.
When building the kernel with a bare-metal (ELF) toolchain, the -shared
option may not be passed down to collect2, resulting in silent corruption
of the vDSO image (in particular, the DYNAMIC section is omitted).
The effect of this corruption is that the dynamic linker fails to find
the vDSO symbols and libc is instead used for the syscalls that we
intended to optimise (e.g. gettimeofday). Functionally, there is no
issue as the sigreturn trampoline is still intact and located by the
kernel.
This patch fixes the problem by explicitly passing -shared to the linker
when building the vDSO.
Cc: <stable@vger.kernel.org>
Reported-by: Szabolcs Nagy <Szabolcs.Nagy@arm.com>
Reported-by: James Greenlaigh <james.greenhalgh@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch renames __cpu_suspend to cpu_suspend so that it's aligned
with ARM32. It also removes the redundant wrapper created.
This is in preparation to implement generic PSCI system suspend using
the cpu_{suspend,resume} which now has the same interface on both ARM
and ARM64.
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We check against compat_sp, but print out arm64's sp - fix it.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The memmap freeing code in free_unused_memmap() computes the end of
each memblock by adding the memblock size onto the base. However,
if SPARSEMEM is enabled then the value (start) used for the base
may already have been rounded downwards to work out which memmap
entries to free after the previous memblock.
This may cause memmap entries that are in use to get freed.
In general, you're not likely to hit this problem unless there
are at least 2 memblocks and one of them is not aligned to a
sparsemem section boundary. Note that carve-outs can increase
the number of memblocks by splitting the regions listed in the
device tree.
This problem doesn't occur with SPARSEMEM_VMEMMAP, because the
vmemmap code deals with freeing the unused regions of the memmap
instead of requiring the arch code to do it.
This patch gets the memblock base out of the memblock directly when
computing the block end address to ensure the correct value is used.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 6c81fe7925 ("arm64: enable context tracking") did not
update el0_sp_pc to use ct_user_exit, but this appears to have been
unintentional. In commit 6ab6463aeb ("arm64: adjust el0_sync so
that a function can be called") we made x0 available, and in the return
to userspace we call ct_user_enter in the kernel_exit macro.
Due to this, we currently don't correctly inform RCU of the user->kernel
transition, and may erroneously account for time spent in the kernel as
if we were in an extended quiescent state when CONFIG_CONTEXT_TRACKING
is enabled.
As we do record the kernel->user transition, a userspace application
making accesses from an unaligned stack pointer can demonstrate the
imbalance, provoking the following warning:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 3660 at kernel/context_tracking.c:75 context_tracking_enter+0xd8/0xe4()
Modules linked in:
CPU: 2 PID: 3660 Comm: a.out Not tainted 4.1.0-rc7+ #8
Hardware name: ARM Juno development board (r0) (DT)
Call trace:
[<ffffffc000089914>] dump_backtrace+0x0/0x124
[<ffffffc000089a48>] show_stack+0x10/0x1c
[<ffffffc0005b3cbc>] dump_stack+0x84/0xc8
[<ffffffc0000b3214>] warn_slowpath_common+0x98/0xd0
[<ffffffc0000b330c>] warn_slowpath_null+0x14/0x20
[<ffffffc00013ada4>] context_tracking_enter+0xd4/0xe4
[<ffffffc0005b534c>] preempt_schedule_irq+0xd4/0x114
[<ffffffc00008561c>] el1_preempt+0x4/0x28
[<ffffffc0001b8040>] exit_files+0x38/0x4c
[<ffffffc0000b5b94>] do_exit+0x430/0x978
[<ffffffc0000b614c>] do_group_exit+0x40/0xd4
[<ffffffc0000c0208>] get_signal+0x23c/0x4f4
[<ffffffc0000890b4>] do_signal+0x1ac/0x518
[<ffffffc000089650>] do_notify_resume+0x5c/0x68
---[ end trace 963c192600337066 ]---
This patch adds the missing ct_user_exit to the el0_sp_pc entry path,
correcting the context tracking for this case.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Fixes: 6c81fe7925 ("arm64: enable context tracking")
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The GIC Hypervisor Configuration Register is used to enable
the delivery of virtual interupts to a guest, as well as to
define in which conditions maintenance interrupts are delivered
to the host.
This register doesn't contain any information that we need to
read back (the EOIcount is utterly useless for us).
So let's save ourselves some cycles, and not save it before
writing zero to it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The elr_el2 and spsr_el2 registers in fact contain the processor state
before entry into EL2. In the case of guest state it could be in either
el0 or el1.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The KVM-VFIO device is used by the QEMU VFIO device. It is used to
record the list of in-use VFIO groups so that KVM can manipulate
them.
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The kernel memtest utility is incredibly useful for detecting memory
problems, but sadly isn't in defconfig.
The memtest itself is only run when the user has explicitly passed a
memtest option on the kernel command line, so simply enabling the option
should not have a negative impact.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Vladimir Murzin <vladimir.murzin@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
section 6.2.17 _CCA states that ARM platforms require ACPI _CCA
object to be specified for DMA-cabpable devices. Therefore, this patch
specifies ACPI_CCA_REQUIRED in arm64 Kconfig.
In addition, to handle the case when _CCA is missing, arm64 would assign
dummy_dma_ops to disable DMA capability of the device.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
tlb.S has been removed since fa48e6f "arm64: mm: Optimise tlb flush logic
where we have >4K granule", so align comment with that.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
After secondary CPU boot or hotplug, the active_mm of the idle thread is
&init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1
and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the
TTBR0_EL1 is already set to the reserved value, there is no need to
perform any context reset.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
So far, we configured the world-switch by having a small array
of pointers to the save and restore functions, depending on the
GIC used on the platform.
Loading these values each time is a bit silly (they never change),
and it makes sense to rely on the instruction patching instead.
This leads to a nice cleanup of the code.
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a new item to the feature set (ARM64_HAS_SYSREG_GIC_CPUIF)
to indicate that we have a system register GIC CPU interface
This will help KVM switching to alternative instruction patching.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- add failure(exception) handling
: of_iomap(), of_find_device_by_node() and kstrdup()
- add common poweroff to use PS_HOLD based for all of exynos SoCs
- add exnos_get/set_boot_addr() helper
- constify platform_device_id and irq_domain_ops
- get current parent clock for power domain on/off
- use core_initcall to register power domain driver
- make exynos_core_restart() less verbose
- add support coupled CPUidle for exynos3250
- fix exynos_boot_secondary() return value on timeout
- fix clk_enable() in s3c24xx adc
- fix missing of_node_put() for power domains
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LybA
-----END PGP SIGNATURE-----
Merge tag 'samsung-mach-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Samsung updates for v4.2
- add failure(exception) handling
: of_iomap(), of_find_device_by_node() and kstrdup()
- add common poweroff to use PS_HOLD based for all of exynos SoCs
- add exnos_get/set_boot_addr() helper
- constify platform_device_id and irq_domain_ops
- get current parent clock for power domain on/off
- use core_initcall to register power domain driver
- make exynos_core_restart() less verbose
- add support coupled CPUidle for exynos3250
- fix exynos_boot_secondary() return value on timeout
- fix clk_enable() in s3c24xx adc
- fix missing of_node_put() for power domains
* tag 'samsung-mach-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (301 commits)
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
ARM: EXYNOS: Get current parent clock for power domain on/off
ARM: SAMSUNG: fix clk_enable() WARNing in S3C24XX ADC
ARM: EXYNOS: Add missing of_node_put() when parsing power domains
ARM: EXYNOS: Handle of_find_device_by_node() and kstrdup() failures
ARM: EXYNOS: Handle of of_iomap() failure
Linux 4.1-rc4
....
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVa7zvAAoJEHm+PkMAQRiGtfMIAILs3sxFtrC1hApgcfRLF/7z
K34bwTRqErzqUO/orTwakEr9kSIpIL0zIPSryTCOTPZLfMGkQjhHXO3KR/DSbbTV
MZ8y/BM/yelFA/Np+1LjbiYjTNRnTRvCoaQihkIH8Rn02g7ob9HyL4gIGKpuGFcZ
04GacL2cgChqsRSACdNef948jCoJXKgcuDpe39DXphDWZnBKNZ3HFuJ6bryGJf9A
1/eCI4is85BNwKPemQUYR0xx83UIzDfrghatZP2mOCDDSA2MNg8HNxLTd12LGoQD
tfgX4B7aftzW9Y7GSEDfZ0IKm2NRzgPmCVj6PjVR/iI0lIK4Aq0Z/lDJxxEq3XQ=
=AJM5
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc6' into next/dt
Linux 4.1-rc6
Conflicts:
arch/arm/boot/dts/zynq-7000.dtsi
Resolution summary:
Mainline had an earlier version of the commit, resolve in favor of the
newer patch in next/dt branch.
The Juno board, and likely many other boards, likes to use simple
GPIO keys for input events. Enabled this in the default
ARM64 defconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The Juno board has two keys connected to a PL061 GPIO block,
in accordance to DDI0524B "ARM Versatile Express Juno Development
Platform" revision 1.0, table 2-4 "GPIO (0) and GPIO (1) used
for additional user key entry". By trial-and-error I found that
these are connected to the two keys named "power" and "home"
on the motherboard.
Register the GPIO block and these two keys in the device tree
using the PL061 GPIO driver and the generic gpio keys.
- Map POWER, HOME, VOL+ and VOL- to the obvious input events.
- Map RLOCK to KEY_SCREENLOCK/KEY_COFFEE unless someone can
explain better what this is for.
- Map the NMI button to KEY_SYSREQ as this is used like so
in the SYSREQ debugging hack.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
When building without CONFIG_HOTPLUG_CPU, GCC complains (rightly) that
psci_tos_resident_on is unused:
arch/arm64/kernel/psci.c:61:13: warning: ‘psci_tos_resident_on’ defined but not used [-Wunused-function]
static bool psci_tos_resident_on(int cpu)
As it's only ever used when CONFIG_HOTPLUG_CPU is selected, let's move
it into the existing ifdef.
Signed-off-by: Will Deacon <will.deacon@arm.com>
[Mark: write commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now FPSIMD don't handle HOTPLUG_CPU. This introduces bug after cpu down/up process.
After cpu down/up process, the FPSMID hardware register is default value, not any
process's fpsimd context. when CPU_DEAD set cpu's fpsimd_state to NULL, it will force
to load the fpsimd context for the thread, to avoid the chance to skip to load the context.
If process A is the last user process on CPU N before cpu down, and the first user process
on the same CPU N after cpu up, A's fpsimd_state.cpu is the current cpu id,
and per_cpu(fpsimd_last_state) points A's fpsimd_state, so kernel will not reload the
context during it return to user space.
Signed-off-by: Janet Liu <janet.liu@spreadtrum.com>
Signed-off-by: Xiongshan An <xiongshan.an@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
[catalin.marinas@arm.com: some mostly cosmetic clean-ups]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
kernel thread's default fpsimd state is zero. When fork a thread, if parent is kernel thread,
and save hardware context to parent's fpsimd state, but this hardware context is user
process's context, because kernel thread don't use fpsimd, it will not introduce issue,
it add a little cost.
Signed-off-by: Janet Liu <janet.liu@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Added Hisilicon ARM64 SoC family support in Kconfig and defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Wc01
-----END PGP SIGNATURE-----
Merge tag 'hi6220-soc-for-4.2' of git://github.com/hisilicon/linux-hisi into next/soc
ARM64: Hisilicon ARM64 SoC Updates for V4.2
- Added Hisilicon ARM64 SoC family support in Kconfig and defconfig
* tag 'hi6220-soc-for-4.2' of git://github.com/hisilicon/linux-hisi:
arm64: Enable Hisilicon ARMv8 SoC family in Kconfig and defconfig
If a syscall is entered without TIF_SYSCALL_TRACE set, then it goes on
the fast path. It's then possible to have TIF_SYSCALL_TRACE added in
the middle of the syscall, but ret_fast_syscall doesn't check this flag
again. This causes a ptrace syscall-exit-stop to be missed.
For instance, from a PTRACE_EVENT_FORK reported during do_fork, the
tracer might resume with PTRACE_SYSCALL, setting TIF_SYSCALL_TRACE.
Now the completion of the fork should have a syscall-exit-stop.
Russell King fixed this on arm by re-checking _TIF_SYSCALL_WORK in the
fast exit path. Do the same on arm64.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Josh Stone <jistone@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add ioremap_wt() to all arch-specific asm/io.h headers which
define ioremap_wc() locally. These headers do not include
<asm-generic/iomap.h>. Some of them include <asm-generic/io.h>,
but ioremap_wt() is defined for consistency since they define
all ioremap_xxx locally.
In all architectures without Write-Through support, ioremap_wt()
is defined indentical to ioremap_nocache().
frv and m68k already have ioremap_writethrough(). On those we
add ioremap_wt() indetical to ioremap_writethrough() and defines
ARCH_HAS_IOREMAP_WT in both architectures.
The ioremap_wt() interface is exported to drivers.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Elliott@hp.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arnd@arndb.de
Cc: hch@lst.de
Cc: hmh@hmh.eng.br
Cc: jgross@suse.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Cc: stefan.bader@canonical.com
Cc: yigal@plexistor.com
Link: http://lkml.kernel.org/r/1433436928-31903-9-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
