Add dsi host helper function implementation for DSI v2
DSI 6G 1.x and DSI 6G v2.0+ controllers
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add dsi host helper functions support for DSI v2 and DSI 6G 1.x
controllers that are under version checks
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
f9cb8d8d83 fixed various race conditions with CTL flush, in particular
flushing and sending the START signal before encoder state was updated.
But it did this a little too well in some cases that don't trigger
encoder->enable(), and CTL[n].FLUSH would never be set. When page flips
happen it would paper over the bug, since the first plag flip would
flush out the state to the hardware.
The issue could be reproduced with, for example, modetest (without the
'-v' argument).
Fixes: f9cb8d8d83 drm/msm/mdp5: rework CTL START signal handling
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Experimentation shows that resuming power quickly after suspending
ends up forcing a system hang for unknown reasons on 5xx targets.
To avoid cycling the power too much (especially during init)
turn up the autosuspend time for a5xx to 250ms and use
pm_runtime_put_autosuspend() when applicable.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When a msm8016 based system is woken up from suspend, the firmware in
the adreno device hangs.
[ 83.903416] qcom-iommu-ctx 1f09000.iommu-ctx: Unhandled context fault: fsr=0x202, iova=0x0000000000000000, fsynr=0x2, cb=1
[ 85.853633] msm 1a00000.mdss: A306: hangcheck detected gpu lockup rb 0!
[ 85.853661] msm 1a00000.mdss: A306: completed fence: 370
[ 85.859073] msm 1a00000.mdss: A306: submitted fence: 372
[ 85.865113] msm 1a00000.mdss: A306: hangcheck recover!
Fix this by adding pm_runtime_force_suspend/pm_runtime_force_resume
as sleep ops.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
To make suspend and resume work on msm8916 platforms, call into the generic
helpers and preserve the state across suspends.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since there's very few callers of these I've decided to do them all in
one patch. With this the unecessarily long drm_mode_connector_ prefix
is gone from the codebase! The only exception being struct
drm_mode_connector_set_property, which is part of the uapi so can't be
renamed.
Again done with sed+some manual fixups for indent issues.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-8-daniel.vetter@ffwll.ch
Right now, the DRM panel logic returns NULL when a panel pointing to
the passed OF node is not present in the list of registered panels.
Most drivers interpret this NULL value as -EPROBE_DEFER, but we are
about to modify the semantic of of_drm_find_panel() and let the
framework return -ENODEV when the device node we're pointing to has
a status property that is not equal to "okay" or "ok".
Let's first patch the of_drm_find_panel() implementation to return
ERR_PTR(-EPROBE_DEFER) instead of NULL and patch all callers to replace
the '!panel' check by an 'IS_ERR(panel)' one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-2-boris.brezillon@bootlin.com
In commits:
34a2ab5e06 ("drm: Add acquire ctx parameter to ->update_plane")
1931529448 ("drm: Add acquire ctx parameter to ->plane_disable")
a pointer to a drm_modeset_acquire_ctx structure was added as an
argument to the method prototypes. The transitional helpers are
supposed to be directly plugged in as implementations of these
methods, but doing so generates a warning. Add the missing
argument.
A number of buggy users were added for drm_plane_helper_disable()
which need to be fixed up for this change, which we do by passing
a NULL ctx argument.
Fixes: 1931529448 ("drm: Add acquire ctx parameter to ->plane_disable")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/E1fa1Zr-0005gT-VF@rmk-PC.armlinux.org.uk
We got a few conflicts in drm_atomic.c after merging the DRM writeback support,
now we need a backmerge to unlock develop development on drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
This patch avoids dereferencing msm_host->dev when it is NULL.
If we find ourselves tearing down dsi before calling
(mdp4|mdp5|dpu)_kms_init(), we'll end up in a state where the dev
pointer is NULL and trying to extract priv from it will fail.
This was introduced in a seemingly innocuous commit to ensure the
arguments to msm_gem_put_iova() are correct (even though that
function has been a stub for ~5 years). Correctness FTW! \o/
Fixes: b01884a286b0 drm/msm: use correct aspace pointer in msm_gem_put_iova()
Cc: Daniel Mack <daniel@zonque.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that all of the msm-specific goo is tucked safely away we can switch
over to using the atomic helper commit directly. \o/
Changes in v2:
- None
Changes in v3:
- Rebased on Archit's private_obj set
Changes in v4:
- None
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Moving further towards switching fully to the the atomic helpers, this
patch removes the hand-rolled worker nonblock commit code and uses the
atomic helpers commit_work model.
Changes in v2:
- Remove commit_destroy()
- Shuffle order of commit_tail calls to further serialize commits
- Use stall in swap_state to avoid abandoned events on disable
Changes in v3:
- Rebased on Archit's private_obj set
Changes in v4:
- None
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Ensure that any queued events are issued when disabling the crtc. This
avoids timeouts when we come back and wait for dependencies (like the
previous frame's flip_done).
Changes in v2:
- None
Changes in v3:
- Rebased on Archit's private_obj set
Changes in v4:
- None
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In preparation for moving to atomic helpers, move the implicit sync
fence handling out of atomic commit and into the plane->prepare_fb()
hook. While we're at it, de-duplicate the mdp*_prepare_fb functions.
Changes in v4:
- Added
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Factor out the commit_tail() portions of complete_commit() into a
separate function to facilitate moving to the atomic helpers in future
patches.
Changes in v2:
- None
Changes in v3:
- Rebased on Archit's private_obj set
Changes in v4:
- None
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
With the addition of "private_objs" in drm_atomic_state, we no longer
need to subclass drm_atomic_state to store state of share resources
that don't perfectly fit within planes/crtc/connector state information.
We can now save this state within drm_atomic_state itself using
the private objects.
Remove the infrastructure that allowed subclassing of drm_atomic_state
in the driver.
Changes in v3:
- Added to the msm atomic helper patch set
Changes in v4:
- None
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
This replaces the usage of the subclassed atomic state (mdp5_state)
with a private_obj state embedded within drm_atomic_state. The latter
method is the preferred approach, since it's simpler to implement
and less prone to errors.
The new API replaces the older and equivalent mdp5_state usage in the
following pattern:
- References to "mdp5_kms->state" (i.e, the old/existing state) is
replaced with mdp5_get_existing_global_state(). In the atomic_check
path, this should be called with the glob_state_lock drm_modeset_lock
alredy taken.
- References to "mdp5_get_state()" are replaced with
mdp5_get_global_state(). This acquires glob_state_lock and uses
drm_atomic_get_private_obj_state() to create a new duplicated state.
Changes in v3:
- Acquire glob_state_lock in mdp5_smp.c
- Added to the msm atomic helper patch set
Changes in v4:
- None
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Global shared resources (hwpipes, hwmixers and SMP) for MDP5 are
implemented as a part of atomic state by subclassing drm_atomic_state.
The preferred approach is to use the drm_private_obj infrastructure
available in the atomic core.
mdp5_global_state is introduced as a drm atomic private object. The two
funcs mdp5_get_global_state() and mdp5_get_existing_global_state() are
the two variants that will be used to access mdp5_global_state.
This will replace the existing mdp5_state struct (which subclasses
drm_atomic_state) and the funcs around it. These will be removed later
once we mdp5_global_state is put to use everywhere.
Changes in v3:
- Added glob_state_lock instead of pushing it into the core
- Added to the msm atomic helper patch set
Changes in v4:
- None
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Even though msm_gem_put_iova() is currently a NOP function, the caller
should pass in the address space pointer it used to obtain the object.
Other call sites were changed in 8bdcd949bb ("drm/msm: pass
address-space to _get_iova() and friends"), but this one seems to have
been forgotten.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This regression stems from 0e08270a1f ("drm/msm: Separate locking of
buffer resources from struct_mutex").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: Rob Clark <rclark@redhat.com>
Fixes: 0e08270a1f ("drm/msm: Separate locking of buffer resources from struct_mutex")
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the error pointer returned by msm_alloc_stolen_fb gets passed
to drm_framebuffer_remove. The latter handles only NULL pointers, thus
a nasty crash will occur.
Drop the unnecessary fail label and the associated checks - both err and
fb will be set at this stage.
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The function dsi_get_cmd_fmt returns enum dsi_cmd_dst_format,
use the correct enum value also for MIPI_DSI_FMT_RGB666/_PACKED.
This has been discovered using clang:
drivers/gpu/drm/msm/dsi/dsi_host.c:743:35: warning: implicit conversion
from enumeration type 'enum dsi_vid_dst_format' to different
enumeration type 'enum dsi_cmd_dst_format' [-Wenum-conversion]
case MIPI_DSI_FMT_RGB666: return VID_DST_FORMAT_RGB666;
~~~~~~ ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Commit 62e3a3e342 changed get_pages() to initialise
msm_gem_object::pages before trying to initialise msm_gem_object::sgt,
so that put_pages() would properly clean up pages in the failure
case.
However, this means that put_pages() now needs to check that
msm_gem_object::sgt is not null before trying to clean it up, and
this check was only applied to part of the cleanup code. Move
it all into the conditional block. (Strictly speaking we don't
need to make the kfree() conditional, but since we can't avoid
checking for null ourselves we may as well do so.)
Fixes: 62e3a3e342 ("drm/msm: fix leak in failed get_pages")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change plumbs the new fb modifier through the various mdp/disp
get_format hooks.
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
[seanpaul pimped out commit message a bit]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Don't leave the event != NULL once it's consumed, this is used a signal
to the atomic helpers that the event will be handled by the driver.
Changes in v2:
- None
Changes in v3:
- Rebased on Archit's private_obj set
Changes in v4:
- None
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the DSI PHY timings are hard-coded for a specific panel
for the 10nm PHY.
Replace this with the auto PHY timing calculator which can calculate
the PHY timings for any panel.
Changes in v4:
- None
Changes in v3:
- None
Changes in v2:
- None
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make sure the video mode engine is on before waiting
for the video done interrupt.
Changes in v4:
- Move setting enabled to false earlier
Changes in v3:
- Move the return value check to another
patch
Changes in v2:
- Replace pr_err with dev_err
- Changed error message
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Check for the return value of wait for video
done waits and print appropriate error message.
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since drm_framebuffer can now store GEM objects directly, place them
there rather than in our own subclass. As this makes the framebuffer
create_handle function the same as the GEM framebuffer helper, we
can reuse that.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20180330141138.28987-21-daniels@collabora.com
It's going away.
v2: Try harder to find them all.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180503093107.25955-1-daniel.vetter@ffwll.ch
A few fixes for 4.17.. thanks to Sean for helping pull together some
of the display related fixes while I was off in compute-land.
* tag 'drm-msm-fixes-2018-04-25' of git://people.freedesktop.org/~robclark/linux:
drm/msm: don't deref error pointer in the msm_fbdev_create error path
drm/msm/dsi: use correct enum in dsi_get_cmd_fmt
drm/msm: Fix possible null dereference on failure of get_pages()
drm/msm: Add modifier to mdp_get_format arguments
drm/msm: Mark the crtc->state->event consumed
drm/msm/dsi: implement auto PHY timing calculator for 10nm PHY
drm/msm/dsi: check video mode engine status before waiting
drm/msm/dsi: check return value for video done waits
Currently the error pointer returned by msm_alloc_stolen_fb gets passed
to drm_framebuffer_remove. The latter handles only NULL pointers, thus
a nasty crash will occur.
Drop the unnecessary fail label and the associated checks - both err and
fb will be set at this stage.
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The function dsi_get_cmd_fmt returns enum dsi_cmd_dst_format,
use the correct enum value also for MIPI_DSI_FMT_RGB666/_PACKED.
This has been discovered using clang:
drivers/gpu/drm/msm/dsi/dsi_host.c:743:35: warning: implicit conversion
from enumeration type 'enum dsi_vid_dst_format' to different
enumeration type 'enum dsi_cmd_dst_format' [-Wenum-conversion]
case MIPI_DSI_FMT_RGB666: return VID_DST_FORMAT_RGB666;
~~~~~~ ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Commit 62e3a3e342 changed get_pages() to initialise
msm_gem_object::pages before trying to initialise msm_gem_object::sgt,
so that put_pages() would properly clean up pages in the failure
case.
However, this means that put_pages() now needs to check that
msm_gem_object::sgt is not null before trying to clean it up, and
this check was only applied to part of the cleanup code. Move
it all into the conditional block. (Strictly speaking we don't
need to make the kfree() conditional, but since we can't avoid
checking for null ourselves we may as well do so.)
Fixes: 62e3a3e342 ("drm/msm: fix leak in failed get_pages")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change plumbs the new fb modifier through the various mdp/disp
get_format hooks.
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
[seanpaul pimped out commit message a bit]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Don't leave the event != NULL once it's consumed, this is used a signal
to the atomic helpers that the event will be handled by the driver.
Changes in v2:
- None
Changes in v3:
- Rebased on Archit's private_obj set
Changes in v4:
- None
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the DSI PHY timings are hard-coded for a specific panel
for the 10nm PHY.
Replace this with the auto PHY timing calculator which can calculate
the PHY timings for any panel.
Changes in v4:
- None
Changes in v3:
- None
Changes in v2:
- None
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make sure the video mode engine is on before waiting
for the video done interrupt.
Changes in v4:
- Move setting enabled to false earlier
Changes in v3:
- Move the return value check to another
patch
Changes in v2:
- Replace pr_err with dev_err
- Changed error message
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Check for the return value of wait for video
done waits and print appropriate error message.
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This adds support for generating coredumps for remoteprocs using
devcoredump, adds the Qualcomm sysmon driver for intra-remoteproc crash
handling and a number of fixes in Qualcomm and IMX drivers.
-----BEGIN PGP SIGNATURE-----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=cxV7
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.17' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
- add support for generating coredumps for remoteprocs using
devcoredump
- add the Qualcomm sysmon driver for intra-remoteproc crash handling
- a number of fixes in Qualcomm and IMX drivers
* tag 'rproc-v4.17' of git://github.com/andersson/remoteproc:
remoteproc: fix null pointer dereference on glink only platforms
soc: qcom: qmi: add CONFIG_NET dependency
remoteproc: imx_rproc: Slightly simplify code in 'imx_rproc_probe()'
remoteproc: imx_rproc: Re-use existing error handling path in 'imx_rproc_probe()'
remoteproc: imx_rproc: Fix an error handling path in 'imx_rproc_probe()'
samples: Introduce Qualcomm QMI sample client
remoteproc: qcom: Introduce sysmon
remoteproc: Pass type of shutdown to subdev remove
remoteproc: qcom: Register segments for core dump
soc: qcom: mdt-loader: Return relocation base
remoteproc: Rename "load_rsc_table" to "parse_fw"
remoteproc: Add remote processor coredump support
remoteproc: Remove null character write of shared mem
Updates for 4.17. Sorry, running a bit late on this, didn't have a
chance to send pull-req before heading to linaro. But it has all been
in linux-next for a while. Main updates:
+ DSI updates from 10nm / SDM845
+ fix for race condition with a3xx/a4xx fence completion irq
+ some refactoring/prep work for eventual a6xx support (ie. when we have
a userspace)
+ a5xx debugfs enhancements
+ some mdp5 fixes/cleanups to prepare for eventually merging writeback
support (ie. when we have a userspace)
* tag 'drm-msm-next-2018-03-20' of git://people.freedesktop.org/~robclark/linux: (36 commits)
drm/msm: fix building without debugfs
drm/msm/mdp5: don't pre-reserve LM's if no dual-dsi
drm/msm/mdp5: add missing LM flush bits
drm/msm/mdp5: print a bit more of the atomic state
drm/msm/mdp5: rework CTL START signal handling
drm/msm: Trigger fence completion from GPU
drm/msm/dsi: fix direct caller of msm_gem_free_object()
drm/msm: strip out msm_fence_cb
drm/msm: rename mdp->disp
drm/msm/dsi: Fix potential NULL pointer dereference in msm_dsi_modeset_init
drm/msm/adreno/a5xx_debugfs: fix potential NULL pointer dereference
drm/msm/dsi: Get byte_intf_clk only for versions that need it
drm/msm/adreno: Use generic function to load firmware to a buffer object
drm/msm/adreno: Define a list of firmware files to load per target
drm/msm/adreno: Rename gpmufw to powerfw
drm/msm: Pass the correct aperture end to drm_mm_init
drm/msm/gpu: Set number of clocks to 0 if the list allocation fails
drm/msm: Replace gem_object deprecated functions
drm/msm/hdmi: fix semicolon.cocci warnings
drm/msm/mdp5: Fix trailing semicolon
...
The adreno driver stopped building when CONFIG_DEBUGFS is disabled:
drivers/gpu/drm/msm/adreno/adreno_device.c: In function 'adreno_load_gpu':
drivers/gpu/drm/msm/adreno/adreno_device.c:153:16: error: 'const struct msm_gpu_funcs' has no member named 'debugfs_init'
if (gpu->funcs->debugfs_init) {
^~
drivers/gpu/drm/msm/adreno/adreno_device.c:154:13: error: 'const struct msm_gpu_funcs' has no member named 'debugfs_init'
gpu->funcs->debugfs_init(gpu, dev->primary);
^~
This adds an #ifdef around the code that references the hidden
pointer.
Fixes: 331dc0bc19 ("drm/msm: add a5xx specific debugfs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If there is only a single DSI interface, don't reserve the first two
layer-mixers for the dual-DSI use-case.
This was causing problems for WB, not being able to assign a LM, on
8x16, which has only two LM's and a single DSI.
Signed-off-by: Rob Clark <robdclark@gmail.com>
For DSI cmd-mode and writeback, we need to write the CTL's START
register to kick things off, but we only want to do that once both
the encoder and the crtc have a chance to write their corresponding
flush bits. The difficulty is that when there is a full modeset
(ie. encoder state has changed) we want to defer the start until
encoder->enable(). But if only plane's have changed, we want to do
this from crtc->commit().
The start_mask was a previous attempt to handle this, but it didn't
really do the right thing since atomic conversion.
Instead track in the crtc state that the start should be deferred,
set to try from encoder's (or in future writeback's) atomic_check().
This way the state is part of the atomic state, and rollback can
work properly if an atomic test fails.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Interrupt commands causes the CP to trigger an interrupt as the command
is processed, regardless of the GPU being done processing previous
commands. This is seen by the interrupt being delivered before the
fence is written on 8974 and is likely the cause of the additional
CP_WAIT_FOR_IDLE workaround found for a306, which would cause the CP to
wait for the GPU to go idle before triggering the interrupt.
Instead we can set the (undocumented) BIT(31) of the CACHE_FLUSH_TS
which will cause a special CACHE_FLUSH_TS interrupt to be triggered from
the GPU as the write event is processed.
Add CACHE_FLUSH_TS to the IRQ masks of A3xx and A4xx and remove the
workaround for A306.
Suggested-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This should be using drm_gem_object_put(). Also since this is done only
in driver unload path, we don't need to synchronize setting tx_gem_obj
to NULL, so juse use the _unlocked() variant.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since new display controller is called "dpu" instead of "mdp". Lets
make the name of the toplevel directory for the display controllers a
bit more generic.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
_dev_ is being dereferenced before it is null checked, hence there
is a potential null pointer dereference.
Fix this by moving the pointer dereference after _dev_ has been
null checked.
Fixes: d4e7f38d70ef ("drm/msm/dsi: check msm_dsi and dsi pointers before use")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
_minor_ is being dereferenced before it is null checked, hence there
is a potential null pointer dereference. Fix this by moving the pointer
dereference after _minor_ has been null checked.
Fixes: 024ad8df763f ("drm/msm: add a5xx specific debugfs")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Newer DSI host controllers (SDM845 in particular) require a new clock
called byte_intf_clk. A recent patch tried to add this as an optional
clock, but it still set 'ret' to an error number if it didn't find it.
This breaks the host's probe for all previous DSI host versions.
Instead of setting this up as an optional clock, try to get the clock
only for the DSI version that supports it.
Fixes: 56558fb ("drm/msm/dsi: Add byte_intf_clk")
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Move a5xx specific code to load firmware into a buffer object to
the generic Adreno code. This will come in useful for future targets.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The number and type of firmware files required differs for each
target. Instead of using a fixed struct member for each possible
firmware file use a generic list of files that should be loaded
on boot. Use some semi-target specific enums to help each target
find the appropriate firmware(s) that it needs to load.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The power management device on the a5xx cores is known as the
GPMU (Graphics Power Management Unit). On a6xx cores the device
was expanded and renamed as the GMU (Graphics Management Unit).
Rename the 'gpmufw' name struct adreno_info as 'powerfw' to
avoid confusion.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
drm_mm_init() takes the start and length of the intended virtual
memory address region but the msm code is passing the end of
the region instead. That would work out if the region started
at 0 but it doesn't so the top of the region sneaks above the
32 bit boundary which won't work because the driver doesn't
support 64 bit addresses for the GPU yet.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If we fail to allocate gpu->grp_clks reset the number of available
clocks to zero to avoid referencing the missing array later.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
drm_gem_object_{reference,unreference,unreference_unlocked} are
deprecated functions, and merely alias to the get/put functions.
Switch to the new names.
Signed-off-by: Steve Kowalik <steven@wedontsleep.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI6G v2.0+ blocks have a new clock input to them called
byte_intf_clk. It's rate is to be set as byte_clk / 2.
Within the clock controller (CC) subsystem, this clock is a
child/descendant of the byte_clk.
Set it up as an optional clock in the DSI host driver. Make sure
that we enable/set its rate only after we configure byte_clk.
This is required for the ancestor clocks in the CC to be
configured correctly.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
SDM845 contains 2 DSI6G v2.2.1 host controllers. Add them in dsi_cfg.
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We try to get the interface clock in dsi_get_config early during DSI's
component bind. Try getting both the "iface" and "iface_clk" clock name
variants so that we are compatible with both new and legacy DT.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Populate the PHY ops with the downstream driver as reference.
There are a couple of TODOs which need to be resolved:
- The PHY timings are all hardcoded for now. This needs to be replaced
with automatic calculations once we get/understand them.
- There are some lane configuration registers which use a new
representation between physical and logical lane mappings. For now,
we've hardcoced them to follow the default mapping (i.e
logical 0 -> phy 0, logical 1 -> phy 1 etc).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Populate PLL clock ops from downstream. This contains the VCO PLL
ops and the registration of standard clk_divider and clk_mux clocks.
Unlike 14nm PLL, the postdividers/mux of the slave PLL doesn't need
to be set to the same values of the postdivs/mux of the master PLL.
Hence, we don't need special postdivider clock ops like we did with
the 14nm PLL driver.
Like the previous PLL drivers, the implementation is slightly different
from downstream. We don't use shadow clocks, but have the ability to
reparent the RCGs to a different source.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add new 10nm DSI PLL/PHY files that will be used on SDM845.
Just populate empty pll/phy funcs for now. These will be filled up
later.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This flags cause cmdstream to be executed from the ringbuffer (RB)
instead of IB1. Normally not something you'd ever want to do, but
it is super useful for firmware debugging.
Hidden behind CAP_SYS_RAWIO and a default=n kconfig option which
depends on EXPERT (and has a suitably scary warning), to prevent
it from being used on accident.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add some debugfs to dump out PFP and ME microcontroller state, as well
as some of the queues (MEQ and ROQ). Also add a debugfs file to trigger
a GPU reset (and reloading the firmware on next submit).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Move null checks of pointer arguments to the beginning of the
modeset init function since they are referenced immediately
instead of after they have already been used.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Check DSI instance id argument against the proper boundary size
to protect against invalid configuration of the DSI id.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make msm_dsi_pll_init consistently return an error code instead
of NULL when pll initialization fails so that later pll
retrieval can check against an error code. Add checks for these
failures after retrieval of src_pll to avoid invalid pointer
dereferences later in msm_dsi_pll_get_clk_provider.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
UAPI Changes:
- drm/vc4: Expose performance counters to userspace (Boris)
Cross-subsystem Changes:
- MAINTAINERS: Linus to maintain panel-arm-versatile in -misc (Linus)
Core Changes:
- Only use swiotlb when necessary (Chunming)
Driver Changes:
- drm/panel: Add support for ARM Versatile panels (Linus)
- pl111: Improvements around versatile panel support (Linus)
----------------------------------------
Tagged on 2018-02-06:
drm-misc-next for 4.17:
UAPI Changes:
- Validate mode flags + type (Ville)
- Deprecate unused mode flags PIXMUX, BCAST (Ville)
- Deprecate unused mode types BUILTIN, CRTC_C, CLOCK_C, DEFAULT (Ville)
Cross-subsystem Changes:
- MAINTAINERS: s/Daniel/Maarten/ for drm-misc (Daniel)
Core Changes:
- gem: Export gem functions for drivers to use (Samuel)
- bridge: Introduce bridge timings in drm_bridge (Linus)
- dma-buf: Allow exclusive fence to be bundled in fence array when
calling reservation_object_get_fences_rcu (Christian)
- dp: Add training pattern 4 and HBR3 support to dp helpers (Manasi)
- fourcc: Add alpha bit to formats to avoid driver format LUTs (Maxime)
- mode: Various cleanups + add new device-wide .mode_valid hook (Ville)
- atomic: Fix state leak when non-blocking commits fail (Leo)
NOTE: IIRC, this was cross-picked to -fixes so it might fall out
- crc: Allow polling on the data fd (Maarten)
Driver Changes:
- bridge/vga-dac: Add THS8134* support (Linus)
- tinydrm: Various MIPI DBI improvements/cleanups (Noralf)
- bridge/dw-mipi-dsi: Cleanups + use create_packet helper (Brian)
- drm/sun4i: Add Display Engine frontend support (Maxime)
- drm/sun4i: Add zpos support + increase num planes from 2 to 4 (Maxime)
- various: Use drm_mode_get_hv_timing() to fill plane clip rectangle (Ville)
- stm: Add 8-bit clut support, add dsi phy v1.31 support, +fixes (Phillipe)
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Samuel Li <Samuel.Li@amd.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlqDUjcACgkQlvcN/ahK
Bwp83Af8D805yWeS/rJ9pLaiaWmfuymMtZVl/IOEssElxFO4d+ya/S4HrcWJQwX6
KinIQiaytKKe3+TXhVRVVwg7nLBFXzaPey6SvFPCgSEa+Bm+b3v0Uk1ll59UfOzs
/IhwIYIvUSCqTVAccpoT8X/85JUQ3iP41RbdfbBwUtpvL+XLl/y29Pw1dtV71ZCH
I3/5zAk3odLd9LuPkyhtg+V1e8pluKlPVGZ0ElOiZ7HlKzc3ekOLNNj563LBHq8y
b2txi2+h/bfBx7PU5JfP6aOKGGameE79/3UExwW0dJJAHqU728KKs/7OaDu7w0vr
UlH0cY/Zc461ejPldXXx8hoKIxJ3bw==
=5EUv
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 4.17:
UAPI Changes:
- drm/vc4: Expose performance counters to userspace (Boris)
Cross-subsystem Changes:
- MAINTAINERS: Linus to maintain panel-arm-versatile in -misc (Linus)
Core Changes:
- Only use swiotlb when necessary (Chunming)
Driver Changes:
- drm/panel: Add support for ARM Versatile panels (Linus)
- pl111: Improvements around versatile panel support (Linus)
----------------------------------------
Tagged on 2018-02-06:
drm-misc-next for 4.17:
UAPI Changes:
- Validate mode flags + type (Ville)
- Deprecate unused mode flags PIXMUX, BCAST (Ville)
- Deprecate unused mode types BUILTIN, CRTC_C, CLOCK_C, DEFAULT (Ville)
Cross-subsystem Changes:
- MAINTAINERS: s/Daniel/Maarten/ for drm-misc (Daniel)
Core Changes:
- gem: Export gem functions for drivers to use (Samuel)
- bridge: Introduce bridge timings in drm_bridge (Linus)
- dma-buf: Allow exclusive fence to be bundled in fence array when
calling reservation_object_get_fences_rcu (Christian)
- dp: Add training pattern 4 and HBR3 support to dp helpers (Manasi)
- fourcc: Add alpha bit to formats to avoid driver format LUTs (Maxime)
- mode: Various cleanups + add new device-wide .mode_valid hook (Ville)
- atomic: Fix state leak when non-blocking commits fail (Leo)
NOTE: IIRC, this was cross-picked to -fixes so it might fall out
- crc: Allow polling on the data fd (Maarten)
Driver Changes:
- bridge/vga-dac: Add THS8134* support (Linus)
- tinydrm: Various MIPI DBI improvements/cleanups (Noralf)
- bridge/dw-mipi-dsi: Cleanups + use create_packet helper (Brian)
- drm/sun4i: Add Display Engine frontend support (Maxime)
- drm/sun4i: Add zpos support + increase num planes from 2 to 4 (Maxime)
- various: Use drm_mode_get_hv_timing() to fill plane clip rectangle (Ville)
- stm: Add 8-bit clut support, add dsi phy v1.31 support, +fixes (Phillipe)
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Samuel Li <Samuel.Li@amd.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
* tag 'drm-misc-next-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc: (115 commits)
drm/radeon: only enable swiotlb path when need v2
drm/amdgpu: only enable swiotlb alloc when need v2
drm: add func to get max iomem address v2
drm/vc4: Expose performance counters to userspace
drm: Print the pid when debug logging an ioctl error.
drm/stm: ltdc: remove non-alpha color formats on layer 2 for older hw
drm/stm: ltdc: add non-alpha color formats
drm/bridge/synopsys: dsi: Add 1.31 version support
drm/bridge/synopsys: dsi: Add read feature
drm/pl111: Support multiple endpoints on the CLCD
drm/pl111: Support variants with broken VBLANK
drm/pl111: Support variants with broken clock divider
drm/pl111: Handle the Versatile RGB/BGR565 mode
drm/pl111: Properly detect the ARM PL110 variants
drm/panel: Add support for ARM Versatile panels
drm/panel: Device tree bindings for ARM Versatile panels
drm/bridge: Rename argument from crtc to bridge
drm/crc: Add support for polling on the data fd.
drm/sun4i: Use drm_mode_get_hv_timing() to populate plane clip rectangle
drm/rcar-du: Use drm_mode_get_hv_timing() to populate plane clip rectangle
...
In order to implement support for grabbing core dumps in remoteproc it's
necessary to know the relocated base of the image, as the offsets from
the virtual memory base might not be based on the physical address.
Return the adjusted physical base address to the caller.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=pLN1
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.16' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This seems to have been a comparatively quieter merge window, I assume
due to holidays etc. The "biggest" change is AMD header cleanups, which
merge/remove a bunch of them. The AMD gpu scheduler is now being made generic
with the etnaviv driver wanting to reuse the code, hopefully other drivers
can go in the same direction.
Otherwise it's the usual lots of stuff in i915/amdgpu, not so much stuff
elsewhere.
Core:
- Add .last_close and .output_poll_changed helpers to reduce driver footprints
- Fix plane clipping
- Improved debug printing support
- Add panel orientation property
- Update edid derived properties at edid setting
- Reduction in fbdev driver footprint
- Move amdgpu scheduler into core for other drivers to use.
i915:
- Selftest and IGT improvements
- Fast boot prep work on IPS, pipe config
- HW workarounds for Cannonlake, Geminilake
- Cannonlake clock and HDMI2.0 fixes
- GPU cache invalidation and context switch improvements
- Display planes cleanup
- New PMU interface for perf queries
- New firmware support for KBL/SKL
- Geminilake HW workaround for perforamce
- Coffeelake stolen memory improvements
- GPU reset robustness work
- Cannonlake horizontal plane flipping
- GVT work
amdgpu/radeon:
- RV and Vega header file cleanups (lots of lines gone!)
- TTM operation context support
- 48-bit GPUVM support for Vega/RV
- ECC support for Vega
- Resizeable BAR support
- Multi-display sync support
- Enable swapout for reserved BOs during allocation
- S3 fixes on Raven
- GPU reset cleanup and fixes
- 2+1 level GPU page table
amdkfd:
- GFX7/8 SDMA user queues support
- Hardware scheduling for multiple processes
- dGPU prep work
rcar:
- Added R8A7743/5 support
- System suspend/resume support
sun4i:
- Multi-plane support for YUV formats
- A83T and LVDS support
msm:
- Devfreq support for GPU
tegra:
- Prep work for adding Tegra186 support
- Tegra186 HDMI support
- HDMI2.0 and zpos support by using generic helpers
tilcdc:
- Misc fixes
omapdrm:
- Support memory bandwidth limits
- DSI command mode panel cleanups
- DMM error handling
exynos:
- drop the old IPP subdriver.
etnaviv:
- Occlusion query fixes
- Job handling fixes
- Prep work for hooking in gpu scheduler
armada:
- Move closer to atomic modesetting
- Allow disabling primary plane if overlay is full screen
imx:
- Format modifier support
- Add tile prefetch to PRE
- Runtime PM support for PRG
ast:
- fix LUT loading"
* tag 'drm-for-v4.16' of git://people.freedesktop.org/~airlied/linux: (1471 commits)
drm/ast: Load lut in crtc_commit
drm: Check for lessee in DROP_MASTER ioctl
drm: fix gpu scheduler link order
drm/amd/display: Demote error print to debug print when ATOM impl missing
dma-buf: fix reservation_object_wait_timeout_rcu once more v2
drm/amdgpu: Avoid leaking PM domain on driver unbind (v2)
drm/amd/amdgpu: Add Polaris version check
drm/amdgpu: Reenable manual GPU reset from sysfs
drm/amdgpu: disable MMHUB power gating on raven
drm/ttm: Don't unreserve swapped BOs that were previously reserved
drm/ttm: Don't add swapped BOs to swap-LRU list
drm/amdgpu: only check for ECC on Vega10
drm/amd/powerplay: Fix smu_table_entry.handle type
drm/ttm: add VADDR_FLAG_UPDATED_COUNT to correctly update dma_page global count
drm: Fix PANEL_ORIENTATION_QUIRKS breaking the Kconfig DRM menuconfig
drm/radeon: fill in rb backend map on evergreen/ni.
drm/amdgpu/gfx9: fix ngg enablement to clear gds reserved memory (v2)
drm/ttm: only free pages rather than update global memory count together
drm/amdgpu: fix CPU based VM updates
drm/amdgpu: fix typo in amdgpu_vce_validate_bo
...
Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.
Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-10-ville.syrjala@linux.intel.com
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Updates for 4.16.. fairly small this time around, main thing is
devfreq support for the gpu.
* tag 'drm-msm-next-2018-01-10' of git://people.freedesktop.org/~robclark/linux:
drm/msm: Add devfreq support for the GPU
drm/msm/adreno: a5xx: Explicitly program the CP0 performance counter
drm/msm/adreno: Read the speed bins for a5xx targets
drm/msm/adreno: Move clock parsing to adreno_gpu_init()
drm/msm/adreno: Cleanup chipid parsing
drm/msm/gpu: Remove unused bus scaling code
drm/msm/adreno: Remove a useless call to dev_pm_opp_get_freq()
drm/msm/adreno: Call dev_pm_opp_put()
drm/msm: Fix NULL deref in adreno_load_gpu
drm/msm: gpu: Only sync fences on rings that exist
drm/msm: fix leak in failed get_pages
drm/msm: avoid false-positive -Wmaybe-uninitialized warning
drm/msm/mdp4: Deduplicate bus_find_device() by name matching
drm/msm: add missing MODULE_FIRMWARE declarations
drm/msm: update adreno firmware path in MODULE_FIRMWARE
drm/msm: free kstrdup'd cmdline
drm/msm: fix msm_rd_dump_submit prototype
drm/msm: fix spelling mistake: "ringubffer" -> "ringbuffer"
Add support for devfreq to dynamically control the GPU frequency.
By default try to use the 'simple_ondemand' governor which can
adjust the frequency based on GPU load.
v2: Fix __aeabi_uldivmod issue from the 0 day bot and use
devfreq_recommended_opp() as suggested by Rob.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Even though the default countable for CP0 is CP_ALWAYS_COUNT (0),
program the selector during HW initialization in an effort to be
up front about which counters are programmed and why.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some 5xx based chipsets have different bins for GPU clock speeds.
Read the fuses (if applicable) and set the appropriate OPP table.
This will only work with OPP v2 tables - the bin will be ignored
for legacy pwrlevel tables.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Move the clock parsing to adreno_gpu_init() to allow for target
specific probing and manipulation of the clock tables.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We don't need to convert the chipid to an intermediate value and
then back again into a struct adreno_rev.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Remove the downstream bus scaling code. It isn't needed for for
compatibility with a downstream or vendor kernel. Get it out of the
way to clear space for devfreq support.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Calling dev_pm_opp_find_freq_floor() returns the matched frequency
in 'freq'. We don't need to call dev_pm_opp_get_freq() again
to get the frequency value.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need to call dev_pm_opp_put() to put back the reference
for the OPP struct after calling the various dev_pm_opp_get_*
functions.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The msm/kms driver should work even if there is no GPU device specified
in DT. Currently, we get a NULL dereference crash in adreno_load_gpu
since the driver assumes that priv->gpu_pdev is non-NULL.
Perform an additional check on priv->gpu_pdev before trying to retrieve
the msm_gpu pointer from it.
v2: Incorporate Jordan's comments:
- Simplify the check to share the same error message.
- Use dev_err_once() to avoid an error message every time we open the
drm device fd.
Fixes: eec874ce5f (drm/msm/adreno: load gpu at probe/bind time)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
divider_recalc_rate() is an helper function used by clock divider of
different types, so the structure containing the 'hw' pointer is not
always a 'struct clk_divider'
At the following line:
> div = _get_div(table, val, flags, divider->width);
in several cases, the value of 'divider->width' is garbage as the actual
structure behind this memory is not a 'struct clk_divider'
Fortunately, this width value is used by _get_val() only when
CLK_DIVIDER_MAX_AT_ZERO flag is set. This has never been the case so
far when the structure is not a 'struct clk_divider'. This is probably
why we did not notice this bug before
Fixes: afe76c8fd0 ("clk: allow a clk divider with max divisor when zero")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The fault recovery code tries to sync fences on all possible rings
instead of only the rings that actually exist which will fault the
kernel when the number of rings are less than the maximum amount.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
