The Tegra DRM driver heavily relies on the implementations for runtime
suspend/resume to be called at specific times. Unfortunately, there are
some cases where that doesn't work. One example is if the user disables
runtime PM for a given subdevice. Another example is that the PM core
acquires a reference to runtime PM during system sleep, effectively
preventing devices from going into low power modes. This is intentional
to avoid nasty race conditions, but it also causes system sleep to not
function properly on all Tegra systems.
Fix this by not implementing runtime PM at all. Instead, a minimal,
reference-counted suspend/resume infrastructure is added to the host1x
bus. This has the benefit that it can be used regardless of the system
power state (or any transitions we might be in), or whether or not the
user allows runtime PM.
Atomic modesetting guarantees that these functions will end up being
called at the right point in time, so the pitfalls for the more generic
runtime PM do not apply here.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make use of the DP link training helpers to implement full and fast link
training. While at it, refactor some of the code and remove various code
sequences that are not necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The CMH, DRVZ and DRVI values vary depending on the SoC generation. Move
them into SoC specific structures so that DT compatible string matching
can be used to select the right parameters and write them to hardware at
the right time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to properly make the VDD supply optional, all accesses to the
regulator need to be ignored, because the regulator core doesn't treat
NULL special.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When a transfer didn't complete transmission of the requested number of
bytes, signal that the transaction should be retried.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The dpaux driver has a quirk built-in that will delay initialization of
the display driver for a short while, trying to detect an eDP panel. The
reason for this quirk is that the panel may not report as connected
until after the display driver has initialized, at which point the fbdev
emulation will have fallen back to 1024x768 as default resolution, which
will likely not be the eDP panel's native resolution.
With upcoming DisplayPort support, the code needs to be able to cope
with hotpluggable monitors as well. Waiting for a panel to show up is no
longer going to work because the monitor may not be attached on boot. If
the output runs in DisplayPort mode, skip waiting for the panel to show
up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
During the discussion of patches that enhance the drm_dp_link helpers it
was concluded that these helpers aren't very useful to begin with. After
all other drivers have been converted not to use these helpers anymore,
move these helpers into the last remaining user: Tegra DRM.
If at some point these helpers are deemed more widely useful, they can
be moved out into the DRM DP helpers again.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191021143437.1477719-14-thierry.reding@gmail.com
Drop use of the deprecated drmP.h header file.
For all touched files divide include files into blocks,
and sort them within the blocks.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190804094132.29463-3-sam@ravnborg.org
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VDD supply is only needed to supply power to eDP panels connected to
DPAUX. Technically that supply should be dealt with in the panel driver,
but for backwards-compatibility we need to keep this around anyway.
Also as a bit of background: the reason for why this supply is attached
to DPAUX is to make sure the panel is properly powered early on so that
it can generate a hotplug pulse at the appropriate time. This may no
longer be required given the support for deferred fbdev setup that was
"recently" introduced in DRM/KMS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of definitions in the code changed the meaning, unfortunately one
place missed the change.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Keep the reset values for the common mode voltage, output driver
impedance control and output driver current control parameters. This
fixes errors seen during SCDC communication with HDMI sinks.
Signed-off-by: Thierry Reding <treding@nvidia.com>
DPAUX is the same as on previous generations. Supporting it is as simple
as adding the compatible string so that the driver will bind to any of
the devices.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move clock and reset management into runtime PM callbacks and hook them
up. This cleans up the code structure so that power management code does
not clutter up the rest.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Register offsets are usually fairly small numbers, so an unsigned int is
more than enough to represent them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The devm_pinctrl_register() function returns an error pointer or a valid
handle. So checking for NULL here is pointless and can never trigger.
Check the returned value with IS_ERR instead and propagate this value as
done in the other functions which call devm_pinctrl_register().
Fixes: 0751bb5c44 ("drm/tegra: dpaux: Add pinctrl support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX pins are shared with an internal I2C controller. To allow
these pins to be muxed to the I2C controller, register a pinctrl device
for the DPAUX device.
This is based upon work by Thierry Reding <treding@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To utilise the DPAUX on Tegra, the SOR power partition must be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework for DPAUX. However, the sequence
for gating/ungating the SOR power partition requires that the DPAUX
reset is asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the
DPAUX driver cannot request the same reset unless we mark the resets as
shared. Sharing resets will not work in this case because we cannot
guarantee that the reset will be asserted/de-asserted at the appropriate
time. Therefore, given that the Tegra generic PM domain code will handle
the DPAUX reset, do not request the reset in the DPAUX driver if the
DPAUX device has a PM domain associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for adding pinctrl support for the DPAUX pads, add a
couple of helpers functions to configure the pads and control their
power.
Please note that although a simple if-statement could be used instead
of a case statement for configuring the pads as there are only two
possible modes, a case statement is used because when integrating with
the pinctrl framework, we need to be able to handle invalid modes that
could be passed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the probing of the DPAUX fails, then clocks are left enabled and the
DPAUX reset de-asserted. Add code to perform the necessary clean-up on
probe failure by disabling clocks and asserting the reset.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of getting a pointer to the driver-specific wrapper of AUX
channels, use the AUX channel objects directly to avoid hackish casting
between the two types.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A address-only I2C_WRITE can't be replied with a short i2c ack, but I
suppose it could be replied with an i2c defer. So the code should be
prepared for an address-only I2C_WRITE_STATUS_UPDATE.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Terje Bergström" <tbergstrom@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the I2C_STATUS request to I2C_WRITE_STATUS_UPDATE to match the
spec.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When the DPAUX isn't attached to an SOR the interrupts are not useful.
This also prevents a race that could potentially cause a crash on driver
removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX code paths already configure the pads in AUX mode, but there
is no way to reconfigure them in I2C mode for HDMI (the DPAUX module is
unused in that case). Enabling the pads in I2C mode by default is the
quickest way to support HDMI. Eventually this may need an explicit call
in the user drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the dpaux device fails, output proper error messages to
help diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The DPAUX registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX read/write FIFO registers aren't sequential in the register
space, causing transfers larger than 4 bytes to cause accesses to non-
existing FIFO registers.
Fixes: 6b6b604215 ("drm/tegra: Add eDP support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename the defines to have levels instead of values for vswing and
pre-emph levels as the values may differ in other scenarios like low vswing of
eDP1.4 where the values are different.
Done using following cocci patch for each define:
@@
@@
# define DP_TRAIN_VOLTAGE_SWING_400 (0 << 0)
+ # define DP_TRAIN_VOLTAGE_SWING_LEVEL_0 (0 << 0)
...
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When tegra-drm.ko is built as a module, these MODULE_DEVICE_TABLEs allow
the module to be auto-loaded since the module will match the devices
instantiated from device tree.
(Notes for stable: in 3.14+, just git rm any conflicting file, since they
are added in later kernels. For 3.13 and below, manual merging will be
needed)
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Doing so allows the hotplug events generated by the connector to be
properly handled by the DRM poll helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Calling the drm_helper_hpd_irq_event() helper can sleep, so instead of
invoking it directly from the interrupt handler, schedule a work queue
and run it from there.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This should avoid races between connector probing and HPD
irqs in the future, currently mode_config.mutex blocks this
possibility.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Certain types of I2C-over-AUX transactions require that only the address
is transferred. Detect this by looking at the AUX message's size and set
the address-only bit appropriately.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
