Generic bitflags attribute content sent to the kernel by user.
With this netlink attr type the user can either set or unset a
flag in the kernel.
The value is a bitmap that defines the bit values being set
The selector is a bitmask that defines which value bit is to be
considered.
A check is made to ensure the rules that a kernel subsystem always
conforms to bitflags the kernel already knows about. i.e
if the user tries to set a bit flag that is not understood then
the _it will be rejected_.
In the most basic form, the user specifies the attribute policy as:
[ATTR_GOO] = { .type = NLA_BITFIELD32, .validation_data = &myvalidflags },
where myvalidflags is the bit mask of the flags the kernel understands.
If the user _does not_ provide myvalidflags then the attribute will
also be rejected.
Examples:
value = 0x0, and selector = 0x1
implies we are selecting bit 1 and we want to set its value to 0.
value = 0x2, and selector = 0x2
implies we are selecting bit 2 and we want to set its value to 1.
Suggested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC Receive Control Register has a 14 bit field indicating the
longest frame that may be received. It is being set to 1522. Frames
longer than this are discarded, but counted as being in error.
When using DSA, frames from the switch has an additional header,
either 4 or 8 bytes if a Marvell switch is used. Thus a full MTU frame
of 1522 bytes received by the switch on a port becomes 1530 bytes when
passed to the host via the FEC interface.
Change the maximum receive size to 2048 - 64, where 64 is the maximum
rx_alignment applied on the receive buffer for AVB capable FEC
cores. Use this value also for the maximum receive buffer size. The
driver is already allocating a receive SKB of 2048 bytes, so this
change should not have any significant effects.
Tested on imx51, imx6, vf610.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PHY is missing but expected, e.g. because of a typ0 in the dt
file, it is not possible to open the interface. ip link returns:
RTNETLINK answers: No such device
It is not very obvious what the problem is. Add a netdev_err() in this
case to make it easier to debug the issue.
[ 21.409385] fec 2188000.ethernet eth0: Unable to connect to phy
RTNETLINK answers: No such device
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egil Hjelmeland says:
====================
net: dsa: lan9303: Fix MDIO issues.
This series fix the MDIO interface for the lan9303 DSA driver.
Bugs found after testing on actual HW.
This series is extracted from the first patch of my first large
series. Significant changes from that version are:
- use mdiobus_write_nested, mdiobus_read_nested.
- EXPORT lan9303_indirect_phy_ops
Unfortunately I do not have access to i2c based system for
testing.
Changes from first version:
- Change EXPORT_SYMBOL to EXPORT_SYMBOL_GPL
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Indirect access (PMI) to phy register only work in I2C mode. In
MDIO mode phy registers must be accessed directly. Introduced
struct lan9303_phy_ops to handle the two modes.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparing for the following fix of MDIO phy access:
Renamed functions that access PHY 1 and 2 indirectly through PMI
registers.
lan9303_port_phy_reg_wait_for_completion() to
lan9303_indirect_phy_wait_for_completion()
lan9303_port_phy_reg_read() to
lan9303_indirect_phy_read()
lan9303_port_phy_reg_write() to
lan9303_indirect_phy_write()
Also changed "val" parameter of lan9303_indirect_phy_write() to u16,
for clarity.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_mdio_write()/_read() must multiply register number by 4 to get
offset.
Added some commments to the register definitions.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle that MDIO read with no response return 0xffff.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu says:
====================
ethtool: support for forward error correction mode setting on a link
Forward Error Correction (FEC) modes i.e Base-R
and Reed-Solomon modes are introduced in 25G/40G/100G standards
for providing good BER at high speeds. Various networking devices
which support 25G/40G/100G provides ability to manage supported FEC
modes and the lack of FEC encoding control and reporting today is a
source for interoperability issues for many vendors.
FEC capability as well as specific FEC mode i.e. Base-R
or RS modes can be requested or advertised through bits D44:47 of base link
codeword.
This patch set intends to provide option under ethtool to manage and
report FEC encoding settings for networking devices as per IEEE 802.3
bj, bm and by specs.
v2 :
- minor patch format fixes and typos pointed out by Andrew
- there was a pending discussion on the use of 'auto' vs
'automatic' for fec settings. I have left it as 'auto'
because in most cases today auto is used in place of
automatic to represent automatically generated values.
We use it in other networking config too. I would prefer
leaving it as auto.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward Error Correction (FEC) modes i.e Base-R
and Reed-Solomon modes are introduced in 25G/40G/100G standards
for providing good BER at high speeds. Various networking devices
which support 25G/40G/100G provides ability to manage supported FEC
modes and the lack of FEC encoding control and reporting today is a
source for interoperability issues for many vendors.
FEC capability as well as specific FEC mode i.e. Base-R
or RS modes can be requested or advertised through bits D44:47 of
base link codeword.
This patch set intends to provide option under ethtool to manage
and report FEC encoding settings for networking devices as per
IEEE 802.3 bj, bm and by specs.
set-fec/show-fec option(s) are designed to provide control and
report the FEC encoding on the link.
SET FEC option:
root@tor: ethtool --set-fec swp1 encoding [off | RS | BaseR | auto]
Encoding: Types of encoding
Off : Turning off any encoding
RS : enforcing RS-FEC encoding on supported speeds
BaseR : enforcing Base R encoding on supported speeds
Auto : IEEE defaults for the speed/medium combination
Here are a few examples of what we would expect if encoding=auto:
- if autoneg is on, we are expecting FEC to be negotiated as on or off
as long as protocol supports it
- if the hardware is capable of detecting the FEC encoding on it's
receiver it will reconfigure its encoder to match
- in absence of the above, the configuration would be set to IEEE
defaults.
>From our understanding , this is essentially what most hardware/driver
combinations are doing today in the absence of a way for users to
control the behavior.
SHOW FEC option:
root@tor: ethtool --show-fec swp1
FEC parameters for swp1:
Active FEC encodings: RS
Configured FEC encodings: RS | BaseR
ETHTOOL DEVNAME output modification:
ethtool devname output:
root@tor:~# ethtool swp1
Settings for swp1:
root@hpe-7712-03:~# ethtool swp18
Settings for swp18:
Supported ports: [ FIBRE ]
Supported link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: [RS | BaseR | None | Not reported]
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: [RS | BaseR | None | Not reported]
<<<< One or more FEC modes
Speed: 100000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 106
Transceiver: internal
Auto-negotiation: off
Link detected: yes
This patch includes following changes
a) New ETHTOOL_SFECPARAM/SFECPARAM API, handled by
the new get_fecparam/set_fecparam callbacks, provides support
for configuration of forward error correction modes.
b) Link mode bits for FEC modes i.e. None (No FEC mode), RS, BaseR/FC
are defined so that users can configure these fec modes for supported
and advertising fields as part of link autonegotiation.
Signed-off-by: Vidya Sagar Ravipati <vidya.chowdary@gmail.com>
Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger says:
====================
netvsc: minor fixes and optimization
This is a subset of earlier submission with a few more fixes
found during testing. The are two small optimizations, one is to
better manage the receive completion ring, and the other is removing
one unneeded level of indirection.
Will submit the improved VF support and buffer sizing in a later
patch so they get more review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Latency improvement related to NAPI conversion.
If all packets are processed from receive ring then need
to signal host.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If setting receive buffer fails, the error unwind would cause
kernel panic because it was not correctly doing RCU and NAPI
unwind. RCU'd pointer needs to be reset to NULL, and NAPI needs
to be disabled not deleted.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize how receive completion ring are managed.
* Allocate only as many slots as needed for all buffers from host
* Allocate before setting up sub channel for better error detection
* Don't need to keep copy of initial receive section message
* Precompute the watermark for when receive flushing is needed
* Replace division with conditional test
* Replace atomic per-device variable with per-channel check.
* Handle corner case where receive completion send
fails if ring buffer to host is full.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal API was passing struct hv_page_buffer **
when only simple struct hv_page_buffer * was necessary
for passing an array.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using %p to print pointer to packet meta-data doesn't give any
good info, and exposes kernel memory offsets.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes a bunch of fixups for issues reported by
lockdep.
* ethtool routines can assume RTNL
* send is done with RCU lock (and BH disable)
* avoid refetching internal device struct (netvsc)
instead pass it as a parameter.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump up driver version to match newer NIC firmware. Also update
nic_rx_stats (a struct common to host driver and firmware) by adding a new
field: fw_total_fwd_bytes.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en depends on MAY_USE_DEVLINK; this is used to force bnxt_en
to be =m when DEVLINK is =m.
Now, bnxt_re selects bnxt_en. Unless bnxt_re also explicitly calls
out dependency on MAY_USE_DEVLINK, Kconfig does not force bnxt_re
to be =m when DEVLINK is =m, causing the following error:
drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.o: In function
`bnxt_dl_register':
bnxt_vfr.c:(.text+0x1440): undefined reference to `devlink_alloc'
bnxt_vfr.c:(.text+0x14c0): undefined reference to `devlink_register'
bnxt_vfr.c:(.text+0x14e0): undefined reference to `devlink_free'
drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.o: In function
`bnxt_dl_unregister':
bnxt_vfr.c:(.text+0x1534): undefined reference to `devlink_unregister'
bnxt_vfr.c:(.text+0x153c): undefined reference to `devlink_free'
Fix this by adding MAY_USE_DEVLINK dependency in bnxt_re.
Fixes: 4ab0c6a8ff ("bnxt_en: add support to enable VF-representors")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently through one of my revisions of the initial patches
series I lost the devmap test. We can add more testing later but
for now lets fix the simple one we have.
Fixes: 546ac1ffb7 "bpf: add devmap, a map for storing net device references"
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
SZ Lin says:
====================
net: moxa: Fix style issues
This patch set fixs the WARNINGs found by the checkpatch.pl tool
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes all checkpatch occurences of
"CHECK: spaces preferred around that '{+,-}' (ctx:VxV)"
in moxart_ether code.
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No space is necessary after a cast
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed coding style for null comparisons in moxart_ether driver
to be more consistent with the rest of the kernel coding style
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'unsigned int' instead of 'unsigned'
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary braces from single-line if statement
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: get rid of unsafe_global_rkey
The smc code uses the unsafe_global_rkey, exposing all memory for
remote reads and writes once a connection is established.
Here is now a patch series to get rid of unsafe_global_rkey usage.
Main idea is to switch to SG-logic and separate memory regions for RMBs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of send buffer "sndbuf" is synced
(a) before filling sndbuf for cpu access
(b) after filling sndbuf for device access
Usage of receive buffer "RMB" is synced
(a) before reading RMB content for cpu access
(b) after reading RMB content for device access
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split function __smc_buf_create() for better readability.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creation and deletion of SMC receive and send buffers shares a high
amount of common code . This patch introduces common functions to get
rid of duplicate code.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC send buffers are processed the same way as RMBs. Since RMBs have
been converted to sg-logic, do the same for send buffers.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now separate memory regions are created and registered for separate
RMBs. The unsafe_global_rkey of the protection domain is no longer
used. Thus the exposing memory warning can be removed.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A memory region created for a new RMB must be registered explicitly,
before the peer can make use of it for remote DMA transfer.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC currently uses the unsafe_global_rkey of the protection domain,
which exposes all memory for remote reads and writes once a connection
is established. This patch introduces separate memory regions with
separate rkeys for every RMB. Now the unsafe_global_rkey of the
protection domain is no longer needed.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The follow-on patch makes use of ib_map_mr_sg() when introducing
separate memory regions for RMBs. This function is based on
scatterlists; thus this patch introduces scatterlists for RMBs.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initiate the coming rework of SMC buffer handling with this
small code cleanup. No functional changes here.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a link group for a new server connection exists already, the mutex
serializing the determination of link groups is given up early.
The coming registration of memory regions benefits from the serialization
as well, if the mutex is held till connection creation is finished.
This patch postpones the unlocking of the link group creation mutex.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall says:
====================
constify inet6_protocol structures
The inet6_protocol structure is only passed as the first argument to
inet6_add_protocol or inet6_del_protocol, both of which are declared as
const. Thus the inet6_protocol structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct inet6_protocol i@p = { ... };
@ok1@
identifier r.i;
expression e1;
position p;
@@
\(inet6_add_protocol\|inet6_del_protocol\)(&i@p,...)
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct inet6_protocol e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct inet6_protocol i = { ... };
// </smpl>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet6_protocol structure is only passed as the first argument to
inet6_add_protocol or inet6_del_protocol, both of which are declared as
const. Thus the inet6_protocol structure itself can be const.
Also drop __read_mostly on the newly const structure.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet6_protocol structure is only passed as the first argument to
inet6_add_protocol or inet6_del_protocol, both of which are declared as
const. Thus the inet6_protocol structure itself can be const.
Also drop __read_mostly where present on the newly const structures.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Farrington says:
====================
liquidio: standardization and cleanup
This patchset corrects some non-standard macro usage.
1. Replaced custom MIN macro with use of standard 'min_t'.
2. Removed cryptic and misleading macro 'CAST_ULL'.
change log:
V1 -> V2:
1. Add driver cleanup of macro 'CAST_ULL'.
V2 -> V3:
1. Remove extra parentheses from previous usage of macro 'CAST_ULL'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a390d1f379 ("phylib: convert state_queue work to
delayed_work"), the PHYLIB state machine was converted to use delayed
workqueues, yet some functions were still referencing the PHY library
timer in their comments, fix that and remove the now unused
linux/timer.h include.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: extend firmware request logic
We have been pondering for some time how to support loading different
application firmwares onto NFP. We want to support both users selecting
one of the firmware images provided by Netronome (which are optimized
for different use cases each) as well as firmware images created by
users themselves or other companies.
In the end we decided to go with the simplest solution - depending on
the right firmware image being placed in /lib/firmware. This vastly
simplifies driver logic and also doesn't require any new API.
Different NICs on one system may want to run different applications
therefore we first try to load firmware specific to the device (by
serial number of PCI slot) and if not present try the device model
based name we have been using so far.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
request_firmware() will fallback to user space helper and may cause
long delays when driver is loaded if udev doesn't correctly handle
FW requests. Since we never really made use of the user space
helper functionality switch to the simpler request_firmware_direct()
call. The side effect of this change is that no warning will be
printed when the FW image does not exists. To help users figure
out which FW file is missing print a info message when we request
each file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
