The Orange Pi Win features a soldered WiFi chip on the board, connected
via the SDIO interface. Add the required DT nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a green status LED, add the DT node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win exposes several UARTs on header pins, and connects one
to the on-board WiFi/Bluetooth chip.
Add the pinmux definitions to the UART nodes, but keep them disabled.
Enable the UART1, which is wired to the Bluetooth chip, and add a serdev
node. There is no binding for the BT8723 yet, so leave this mostly empty
for now.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has the usual Gigabit PHY connected to the EMAC.
Its power is controlled by GPIO PD14.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a micro USB-B socket, connected to the SoC's
USB-OTG port. Its power is supplied by the AXP PMIC, and the ID pin is
connected to GPIO PH9. It can serve both as a host or a client port.
Add the respective DT nodes to enable it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: enable paired EHCI/OHCI device nodes and regulator supply]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has four standard USB-A sockets, connected to an
on-board USB hub. The hub's and socket's power regulators are enabled by
GPIO PD7.
Add the regulator to the DT to enable the power supply.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a microSD card slot which is connected via all
four SD data lines. As the DT was not mentioning this fact, we got the
default single bit transfers, losing out on performance.
Also, as microSD does not have a write protect switch, we disable this
feature in the DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, though the
board has the SoC and DRAM integrated on one PCB.
Due to this it basically shares the DT with the SoPine baseboard, which
we mimic in our DT by inclucing the boardboard .dts into the new file,
just overwriting the model name.
Having a separate .dts for this seems useful, since we don't know yet if
there are subtle differences between the two. Also the SoC on the LTS
board is technically an "R18" instead of the original "A64", although as
far as we know this is just a relabelled version of the original SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Current kernels complain when booting on an A64 Soc:
....
[ 1.904297] cacheinfo: Unable to detect cache hierarchy for CPU 0
....
Not a real biggie on this flat topology, but also easy enough to fix.
Add the L2 cache node and let each CPU point to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Another user of cd-inverted seems to have crept in. Switch it away from
cd-inverted to be consistent with other sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 have a SID controller which consist of EFUSE (starting at 0x200)
and three registers to read/write some of the protected efuses.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pine H64 board have a MicroSD slot connected to MMC0 controller of
the H6 SoC and a eMMC slot connected to MMC2.
Enable them in the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 SoC have 3 MMC controllers.
Add device tree nodes for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
address-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 board has an AXP805 PMIC on it, wired up in standalone, or
self-working, mode.
Enable it in the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Now that the device tree binding headers for the R_CCU have been merged,
we can use the macros, instead of raw numbers.
Switch to R_CCU macros for clock and reset indices.
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
On usual A64 board design the power of HDMI controller is connected to
DLDO1 of the AXP803 PMIC. If this regulator is shut down, the HDMI
output will be blank. Therefore the simplefb driver should keep this
regulator on.
Add the regulator to all currently available A64 boards' simplefb_hdmi
device node, if the board is capable of outputing HDMI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As the U-Boot bootloader now is also capable of initialize the HDMI on
A64 boards, add a simplefb device tree node for accessing the HDMI
framebuffer initialized by the bootloader.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As we have all necessary parts to enable the DE2 CCU on the Allwinner
A64 SoC, add the needed device tree nodes, including the DE2 CCU itself
and the DE2 bus.
The "mixer0-lcd0" simplefb device node is updated to use the DE2 CCU.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pine H64 has 3 GPIO-controlled LEDs, which are labeled "heartbeat",
"link", and "status".
Add device nodes for them.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently all ARM kernels will have s2idle enabled if CONFIG_SUSPEND is
present. In this case if the lid is closed, systemd-logind will enter
s2idle mode by default; however there's no possible wakeup source
defined, so the system will enter a forever idle.
Add the lid itself as a wakeup source, thus the system can wakeup when
the lid is opened.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Originally the name of the DLDO3 regulator on TERES-I is "eDP12", which
is not consistent with other regulator names.
Change it to "vdd-edp", in order to make it more consistent.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The card detect GPIO for Sopine and Pine64-LTS is PF6.
Add this to the dts.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a SRAM controller, and in the device tree currently
we have a syscon node to enable EMAC driver to access the EMAC clock
register. As SRAM controller driver can now export regmap for this
register, replace the syscon node to the SRAM controller device node,
and let EMAC driver to acquire its EMAC clock regmap.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Updated compatible string]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:
USB:
- Two external USB ports (one is directly connected to A64's OTG
controller, the other is under a internal hub connected to the host-only
controller.)
- USB HID keyboard and touchpad connected to the internal hub.
- USB UVC camera connected to the internal hub.
Power-related:
- A DC IN jack connected to AXP803's DCIN pin.
- A Li-Polymer battery connected to AXP803's battery pins.
Storage:
- An eMMC by Foresee on the main board (in the product revision of the
main board it's designed to be switchable).
- An external MicroSD card slot.
Display:
- An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge.
- A mini HDMI port.
Misc:
- A Hall sensor designed to detect the status of lid, connected to GPIO PL12.
- A headphone jack connected to the SoC's internal codec.
- A debug UART port muxed with headphone jack.
This commit adds basical support for it.
[vasily: squashed several commits into one, added simplefb node, added usbphy
to ehci0 and ohci0 nodes and other cosmetic changes to dts]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner A64 SoC features two PWM controllers, which are fully
compatible to the one used in the A13 and H3 chips.
Add the nodes for the devices (one for the "normal" PWM, the other for
the one in the CPUS domain) and the pins their outputs are connected to.
On the A64 the "normal" PWM is muxed together with one of the MDIO pins
used to communicate with the Ethernet PHY, so it won't be usable on many
boards. But the Pinebook laptop uses this pin for controlling the LCD
backlight.
On Pine64 the CPUS PWM pin however is routed to the "RPi2" header,
at the same location as the PWM pin on the RaspberryPi.
Tested on Pinebook and Teres-I
[vasily: fixed comment message as requested by Stefan Bruens, added default
muxing options to pwm and r_pwm nodes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Outside of SOC few chips need external clock source
through RTC example Wifi chip. So RTC clock nodes to
phandle 32kHz external oscillator.
prefix rtc- with clock-output-names defined in
dt-binding to avoid confusion with existing osc32k name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The OrangePi PC2 have an mx25l1606e spi flash.
Add a node for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Sopine and Pine64-LTS have a winbond w25q128 spi flash on spi0.
Add a node for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We mostly have some changes to support the H6, Allwinner latest SoC. We're
still in the preliminary phase, with I2C, pinctrl and clock support.
-----BEGIN PGP SIGNATURE-----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=d7Ql
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 changes for 4.18
We mostly have some changes to support the H6, Allwinner latest SoC. We're
still in the preliminary phase, with I2C, pinctrl and clock support.
* tag 'sunxi-dt64-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: h6: add PCF8563 RTC on Pine H64 board
arm64: allwinner: h6: add R_I2C controller
arm64: allwinner: h6: add R_INTC interrupt controller
arm64: allwinner: h6: add node for R_PIO pin controller
arm64: allwinner: h6: add PRCM CCU device node
arm64: dts: allwinner: a64: bananapi-m64: add usb otg
arm64: dts: allwinner: axp803: Add drivevbus regulator
arm64: allwinner: h6: restore the usage of CCU slice macros
Signed-off-by: Olof Johansson <olof@lixom.net>
Pine H64 board has a PCF8563 dedicated RTC connected to its R_I2C bus.
Enable the R_I2C bus and add the RTC to the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has a R_I2C controller wired to the PL0/PL1 pins, which
are used in the reference design to connect AXP805 PMIC.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has also a R_INTC interrupt controller like Allwinner
A64 SoC, but has its base address changed due to the memory map change
in H6.
Add it into the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has a R_PIO pin controller which controls PL and PM
GPIO banks.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 has also a PRCM CCU.
Add its device node into the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H2+, H3,
or H5 SoCs with the same PCB.
The board has 2GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
This patch enables the H5 variant using the H3 board definition moved to
a common dtsi in an earlier patch. The dts simply include the common dtsi
and declares the correct compatible and model of the H5 variant.
Suggested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The dtb entries for NanoPi boards in the device tree makefile somehow
ended up after the Orange Pi boards.
Move them so the list is properly sorted.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
At the board level, we want to be able to specify what regulator
supplies power to the cpu domain.
Add a label to the first cpu node so we can reference it later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add usb otg support for bananapi-m64 board,
- USB-ID connected with PH9
- USB-DRVVBUS controlled by N_VBUSEN pin from PMIC
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add reg_drivevbus regualtor for boards which are using
external regulator to drive the OTG VBus through N_VBUSEN
PMIC pin.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
As the definition of CCU slice macros are already merged into the source
tree, restore the usage of the macros now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
-----BEGIN PGP SIGNATURE-----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=hXvM
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
* tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
ARM: dts: sun8i-h3: Add Mali node
ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards
ARM: dts: sun8i: h3: Enable HDMI output on H3 boards
ARM: dts: sunxi: h3/h5: Add HDMI pipeline
ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node
ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi
ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl
ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
ARM: dts: nanopi-neo-air: Add WiFi / eMMC
The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG
This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.
Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 SoC features two display pipelines, one has a LCD output, the
other has a HDMI output.
Add support for simplefb for the LCD output. Tested on Teres I.
This patch was inspired by work of Icenowy Zheng.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add a watchdog node for the A64, automatically enabled on all boards.
Since the device is compatible with an existing driver, we only reserve
a new compatible string to be used together with the fall back.
Tested on Olimex Teres-I.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the proper pin group node to reference in board files.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
