following (and including) the new Mali Midgard binding; a lot of
improvements for the rk3228/rk3229 socs (tsadc, operating points,
usb, clock-rates, pinctrl, watchdog); finalizing the rk1108->rv1108
rename and adc buttons for the rk3288 firefly boards.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlk5x+gQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgVOmB/sHN5YBQCwdlermcO75CiLktacneQ6qcom2
GCBHfKwXxmey7puB8cKfQ1IgvvsKmXU1+QbUDjxD13p7b139WVRM3VEokOiSR7cl
XjGFFy9u6ECfPRpJfPBN/8oENcZ1N94S3gfhCwgcF6JDkumMI4DWVTLD4lZLeIcR
LTfZMddSevITXMzrWh0+Q9/TgnJbD58x4lSxs5m85h/8JDSfqdsijs/j2HJrBHPv
01NwQBm8w6rmTNL3UGfqDeUZTnmaczXRf2sgEr5ORLln2Qn++FpUaJiRPUdtYRs7
NEWLppFQeykoxgTQnttkt8oOyaKfNS3PsvwgA7R35w5HnbEtXcDK
=b2HZ
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
A bunch of changes including mali gpu nodes for rk3288 boards
following (and including) the new Mali Midgard binding; a lot of
improvements for the rk3228/rk3229 socs (tsadc, operating points,
usb, clock-rates, pinctrl, watchdog); finalizing the rk1108->rv1108
rename and adc buttons for the rk3288 firefly boards.
* tag 'v4.13-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable usb for rk3229 evb board
ARM: dts: rockchip: add usb nodes on rk322x
ARM: dts: rockchip: add adc button for Firefly
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-veyron
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-firefly
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-rock2-som
ARM: dts: rockchip: add ARM Mali GPU node for rk3288
dt-bindings: gpu: add bindings for the ARM Mali Midgard GPU
ARM: dts: rockchip: set a sane frequence for tsadc on rk322x
ARM: dts: rockchip: add operating-points-v2 for cpu on rk322x
ARM: dts: rockchip: set default rates for core clocks on rk322x
ARM: dts: rockchip: add second uart2 pinctrl on rk322x
ARM: dts: rockchip: correct rk322x uart2 pinctrl
ARM: dts: rockchip: add watchdog device node on rk322x
clk: rockchip: add clock-ids for more rk3228 clocks
clk: rockchip: add ids for camera on rk3399
ARM: dts: rockchip: fix rk322x i2s1 pinctrl error
ARM: dts: rockchip: rename RK1108-evb to RV1108-evb
ARM: dts: rockchip: rename core dtsi from RK1108 to RV1108
ARM: dts: rockchip: Setup usb vbus-supply on rk3288-rock2
Signed-off-by: Olof Johansson <olof@lixom.net>
EV3 battery support, DMA support for MUSB, and non-critical fixes to
GPIO nodes of DA850's GPIO controller and GPIO expander available on
DA850 EVM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZOSmIAAoJEGFBu2jqvgRNFNUP/irdqTUCOPUdpHS+Qrsz1+CE
4U0VpEvFnrlRqJa97zZ1Tps71x0UFfIcVJDveY8rTGK4rMNR6pgalf8PIT+65UVi
exWxkF+OIOjqS6wKu9zN6yn8RemNViiAqtGwcoI9AUAeX+dBg7IZ58bBGAtNf0uy
5Bn99C/5jompTPUPSnZTv5ZW0BZmv8El5WUL3wQh4nT24BzfrAI0miI3d8lW5MKF
/ttkinxeFy9xZEaE+xOKkGtcg4z4JhfalEHtCQhRweE+VJJwEGwdghFs3AT3GLO8
ksRufJzB1R/KEexL9qeHWY+VXRVF1tbdzbDcdrHjqxYUlTVxda5+36NOYANzz3NT
heGXn4mAPm5YiE78ygV7dMaaSMlq6ahjmVSmGjmMvUHFSUaK4WVS8OVJxOmZhi6k
mkxaJ2PIyzFBUlpu35435VqkAc7k5EyKni+HilW5kg4a2o3K0HjS8M1tvf/CkvVk
3evOnVqHare4UajPCQiIPnbSld3fXPl/g7dxLbyXBPY1FtrWxK9Vz11TdpzkiNAy
g2TJFJSQ39lStamW3i1ZAMzej0QCQnsJnZsY7e6JHHfJBxvvKiy3pjlZqhHN7N9M
joFSwaaye05HKacLhKGkSN/NY5fPHDEixc8V1NeoqODan3XoCv6naIjAXMDObASu
vxUIUeg4o7xHjnuGgQ7h
=ZLlm
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.13/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Miscellaneous DT support updates for DA850. Includes Lego mindstorms
EV3 battery support, DMA support for MUSB, and non-critical fixes to
GPIO nodes of DA850's GPIO controller and GPIO expander available on
DA850 EVM.
* tag 'davinci-for-v4.13/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: fix tca6416 for use with GPIO hogs
ARM: dts: da850: Add interrupt-controller property to gpio node
ARM: dts: da850: Add CPPI 4.1 DMA to USB OTG controller
ARM: dts: da850-lego-ev3: Add node for LEGO MINDSTORMS EV3 Battery
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for am335x-boneblue. The rest of
the changes are for enabling features on various
devices with the git shortlog describing the changes.
-----BEGIN PGP SIGNATURE-----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=u58m
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.13 merge window.
This adds support for am335x-boneblue. The rest of
the changes are for enabling features on various
devices with the git shortlog describing the changes.
* tag 'omap-for-v4.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: dts: am33xx: Remove redundant interrupt-parent property
ARM: dts: bonegreen-wireless: add WL1835 Bluetooth device node
ARM: dts: AM43XX: Remove min and max voltage values for dcdc3
ARM: dts: Add am335x-boneblue
ARM: dts: twl4030: Add missing madc reference for bci subnode
ARM: dts: am43xx-clocks: Add support for CLKOUT2
ARM: dts: Configure USB host for 37xx-evm
ARM: dts: omap: Add generic compatible string for I2C EEPROM
ARM: dts: Enable earlycon stdout path for LogicPD torpedo
ARM: dts: Enable earlycon stdout path for duovero
arm: dts: boneblack-wireless: add WL1835 Bluetooth device node
ARM: dts: am571x-idk: Enable the system mailboxes 5 and 6
ARM: dts: am572x-idk: Enable the system mailboxes 5 and 6
ARM: dts: omap4-devkit8000: fix gpmc ranges property
ARM: dts: omap3: Remove 'enable-active-low' property
ARM: dts: OMAP5: uevm: add µSD card detect
ARM: dts: omap4-droid4: Add bluetooth
ARM: dts: dra7x-evm: Enable dual-role mode for USB1
ARM: dts: Use - instead of @ for DT OPP entries for TI SoCs
ARM: dts: am335x-phycore-som: fix rv4162 compatible
Signed-off-by: Olof Johansson <olof@lixom.net>
In order GPIOS from this controller to be used with the "gpio-hogs"
property, the tca6416 node has to properly labeled as a gpio-controller,
and use #gpio-cells.
With that, the SEL_A, SEL_B, SEL_C lines that are used to select VPIF
input can be configured using GPIO hogs.
As an example, example, the configuration below selects the analog video
input on the da850-evm UI board:
&tca6416 {
status = "okay";
sel_a {
gpio-hog;
gpios = <7 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "ADC_ENn";
};
sel_b {
gpio-hog;
gpios = <6 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "CAMERA_ENn";
};
sel_c {
gpio-hog;
gpios = <5 GPIO_ACTIVE_HIGH>;
output-low;
line-name = "VIDEO_IN_ENn";
};
};
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Interrupt-parent property is defined in the root node as
"interrupt-parent = <&intc>". This interrupt-parent value becomes
the default for the system, so removed redundant "interrupt-parent"
property from mmc, mac, lcdc and tscadc nodes.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the serial slave device for the WL1835 Bluetooth interface.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Ricardo Salveti <ricardo.salveti@linaro.org>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dcdc3 supplies to DDR on AM43x series. When we set both
min and max values to the same value. The regulator framework
sets that particular voltage. This is bad as we are changing
the ddr voltage when executing from ddr. Hence remove the min and
max values. The ddr supply voltage shall be set from bootloader
when not executing from ddr and not while executing from kernel.
The previous discussion can be found here:
http://www.spinics.net/lists/devicetree/msg56399.html
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBone Blue is robotics-oriented version of the BeagleBone Black (BBB).
This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]
http://beagleboard.org/bluehttps://github.com/beagleboard/beaglebone-blue
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Acked-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The twl4030_charger driver expects an iio channel to detect the
presence of an AC charger by looking at VAC (madc channel 11).
This definition is missing in the device tree.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rockchip's rk3229 evaluation board has one usb otg controller
and three usb host controllers. Each usb controller connect
with one usb2 phy port through UTMI+ interface. And the three
usb host interfaces use the same GPIO VBUS drive. Let's enable
them to support usb on rk3229 evb board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds usb otg/host controllers and phys nodes on rk322x.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This augments the Moxa Art and Aspeed device trees to:
- Explicitly name the clock "PCLK" as the Faraday FTTMR010
names it.
- List the Moxa timer as compatible with the Faradat FTTMR010
vanilla version.
- Add a comment that the Aspeed driver is a Faraday
FTTMR010 derivative.
- Pass all IRQs to the timer from Aspeed: they are all there
so they should be in the device tree, we only use the
first one anyways.
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the reset and clock lines to the Gemini core DTS SoC.
These bindings have been ACKed by the DT maintainer Rob.
The reset driver is going to be merged by the reset maintainer.
The clock driver is going to be merged by the clock maintainers.
Each of these have their macro defines coming with them, split
off as separate patches.
A post-rc1 patch will be sumbitted for switching the numerical
values to the defined macros in line with the ARM SoC DT header
merge strategy.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZJUpbAAoJEEEQszewGV1zXSEQAIGcFltGHqLrbaM1Zc1I2XG3
H1j0W09hQ5Zbnee09x1WBXRt6ickyCjlUb+Is969kF3BANvBGv1kl5UEoHhi86Yp
JmvjxWkXcdqZrkQYobQd3Zi1Okd9W6sTBupVApbErieEYQIhqV7h5yTVdx3UIoEE
dlLesk4l1aDuxAH0xM2o1fIXYH73ZWgRuEcGZlVDw/CgMWFjvmG1twQ1TtTWMDWS
p29we0TjF18aP9fGlf1bBtbKgrrt23NIniuPvriwmUhpWPA/C2fKcw51G39m3Eqv
2ep8azFotJB4EZ4lCv+24GojEkF5I+BmFaeMY/yV3jb2+Gufni7aSpc7c0yM8Zb8
hLrlzbyCBU0Xc/xCuD7Hu0HoTIriJB7YM4W5O9pB3IJvrEjK6kc/tGSZa0YvmurC
qlftNzFDwnUELUOtbOvA2g0BOMHxvbmUDHkFtFH6tWWgLGHsf7axLJSprQZgrmAJ
Pq17XWWiLz3/bSkSOkGncIejp3Ed+5fo7kk06Dn4THCss7pD/KioFd6Wwi+Y2AEX
TF7qP0t6KK9rN5Y1N6H1PRMFjKXARw/Qt3NhbG6RX2PCUPoD/upx6gzsO1Zu+7na
kaZ2qUu2bjB1IQl0f2VGFfzExSBAyEZScFRGAvbY0EKwfI+tipupfsJgu0ocRfk2
DxfT+fD+K35OSvMZ7V41
=SNKP
-----END PGP SIGNATURE-----
Merge tag 'gemini-v4.13-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
This is a first set of Gemini DTS patches for the v4.13 cycle.
This adds the reset and clock lines to the Gemini core DTS SoC.
These bindings have been ACKed by the DT maintainer Rob.
The reset driver is going to be merged by the reset maintainer.
The clock driver is going to be merged by the clock maintainers.
Each of these have their macro defines coming with them, split
off as separate patches.
A post-rc1 patch will be sumbitted for switching the numerical
values to the defined macros in line with the ARM SoC DT header
merge strategy.
* tag 'gemini-v4.13-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add clocks to the Gemini SoC
ARM: dts: Add the Gemini reset controller
dt-bindings: Augment Gemini for clocks, resets
Signed-off-by: Olof Johansson <olof@lixom.net>
* Switch to panel-lvds bindings for Mitsubishi panels
* Clean up PFC node names
* Enable UHS-I SDR-50 and SDR-104 on r8a7793/Gose
* Add GyroADC clock and device for r8a7791 SoC
* Add USB clocks to device tree for r7s72100 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3Bjz
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.13
* Switch to panel-lvds bindings for Mitsubishi panels
* Clean up PFC node names
* Enable UHS-I SDR-50 and SDR-104 on r8a7793/Gose
* Add GyroADC clock and device for r8a7791 SoC
* Add USB clocks to device tree for r7s72100 SoC
* tag 'renesas-dt-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: renesas: Switch to panel-lvds bindings for Mitsubishi panels
ARM: dts: gose: Enable UHS-I SDR-50 and SDR-104
ARM: dts: r8a7793: set maximum frequency for SDHI clocks
ARM: dts: r8a7791: Add GyroADC clock and device node
ARM: dts: r7s72100: add usb clocks to device tree
ARM: dts: sh73a0: update PFC node name to pin-controller
ARM: dts: r8a7793: update PFC node name to pin-controller
ARM: dts: r8a7791: update PFC node name to pin-controller
ARM: dts: r8a7790: update PFC node name to pin-controller
ARM: dts: r8a7779: update PFC node name to pin-controller
ARM: dts: r8a7778: update PFC node name to pin-controller
ARM: dts: r8a7740: update PFC node name to pin-controller
ARM: dts: r8a73a4: update PFC node name to pin-controller
ARM: dts: emev2: update PFC node name to pin-controller
ARM: dts: r7s72100: add USB bit definitions
ARM: dts: r7s72100: add Renesas RZ/A1 pinctrl header
ARM: dts: r8a7791: add GyroADC clock
Signed-off-by: Olof Johansson <olof@lixom.net>
The only adc button connected to adc input is recovery button.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the needed clock nodes for the CLKOUT2 to be usable by boards.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The gpio node has 144 gpios. Each gpio is capable of generating
an interrupt. Hence add interrupt-controller property to the gpio
node. With this in place one can use interrupts property in device
tree to request for the gpio interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds CPPI 4.1 DMA controller to USB OTG controller.
Changes since v2:
- Fixed the the property reg-names (had glue register defined)
- Removed few useless property
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Looks like nobody bothered to configure USB host for 37xx-evm
when we converted things to device tree, so let's add it. This
is similar to beagleboard configuration with few extra quirks
to configure the port. And as with beagleboard, OHCI won't work
because there is no USB LS/FS PHY. A HS USB hub is needed to use
devices like keyboard and mice.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Acked-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the serial slave device for the WL1835 Bluetooth interface.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the AM571x IDK board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, and DSP1 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the AM572x IDK board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With two separate &gpmc nodes the second ranges property overwrites the
first. So put nand and ethernet in a single node and merge the ranges.
While at it also fix the ethernet suffix.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have a clock controller for the Gemini SoC, so make use of the
driver and add clocks to the peripherals. Remove the hard-coded
frequency from the UART and add switch the timer compatible to the
generic that uses the clock framework for clock speed look-up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the Gemini reset controller to the Gemini SoC
DTSI file and also adds the reset references to all existing
blocks already in the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add reference to the Mali GPU device tree node on rk3288-veyron.
Tested on Minnie and Jerry boards.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add reference to the Mali GPU device tree node on rk3288-firefly.
Tested on Firefly board.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add reference to the Mali GPU device tree node on the
rk3288-rock2-som platform. Tested on a Radxa Rock2 Square board.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add Mali GPU device tree node for the rk3288 SoC, with devfreq
opp table.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Property 'enable-active-low' does not exist. Only 'enable-active-high' is
valid, and when this property is absent the gpio regulator will act as
active low by default.
So remove the unexisting 'enable-active-low' property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update freq of tsadc's working clock as 32768 hz, if not set, tsadc
will work at a default frequence.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds a new opp table for cpu on rk322x SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Set sane default frequencies for CPLL, GPLL and some other core clocks
on the rk322x.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
-----BEGIN PGP SIGNATURE-----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=My0U
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.12-rc cycle most consisting of few minor dts fixes
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
* tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: Reduce cpu thermal shutdown temperature
memory: omap-gpmc: Fix debug output for access width
ARM: dts: LogicPD Torpedo: Fix camera pin mux
ARM: dts: omap4: enable CEC pin for Pandaboard A4 and ES
ARM: dts: gta04: fix polarity of clocks for mcbsp4
ARM: dts: dra7: Add power hold and power controller properties to palmas
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZHav8AAoJEFBXWFqHsHzOPWMH/RP4LuJDUoFaPUJ3WsrMhPYR
qmBEzZXvjKBxImFCIiG09vcjQIiN9p5uZ9AqNIQGgoW20DlFKVZ0Rd64MJzp8QnL
J/WwEDTG1qs2jCkNWYkFEUwz6fMWzzTUydj665dkQI3SNwRAJ9dE0LgybM6Yws3C
FQdIUyWR2z8QQYqjLTD9XuDe7ewyoslvFssWRiVzpcnkiu8sWgbTuJ/K+ISCgwo4
rC6Vi7Z4WU47SgL7+d9sOMzDPDIif5mOdfW8uG3tgCeDp/8WNz9IbamCuxhggQpa
+k9jaTHAtOV9ypf1PBUCGHazU7E8hc42XoW6XT0yY3sFynw+VPd1IFVXiWAEBu0=
=gQA8
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.12:
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
* tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: add PM dependency for IMX7_PM_DOMAINS
ARM: dts: imx6sx-sdb: Remove OPP override
ARM: dts: imx53-qsrb: Pulldown PMIC IRQ pin
Signed-off-by: Olof Johansson <olof@lixom.net>
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
-----BEGIN PGP SIGNATURE-----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=6jUO
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
* tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm2835: add index to the ethernet alias
ARM: dts: bcm2835: fix uart0/uart1 pins
ARM: dts: bcm2835: fix i2c0 pins
ARM: dts: bcm2835: fix uart0 pinctrl node names
Signed-off-by: Olof Johansson <olof@lixom.net>
We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.
Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.
As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.
Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.
As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.
Fixes: 4027494ae6 ('ARM: dts: add arm/arm64 include symlinks')
Reported-by: Russell King <linux@armlinux.org.uk>
Reported-by: Omar Sandoval <osandov@osandov.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-arch <linux-arch@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZF2pwAAoJEHm+PkMAQRiG9aAIAJJyV6Ux9kaX+glqO3KIs0wm
0K/yqMOv1JTfJ1UUgY4iZbk5XOPPmXv1bdKJFECZfuAHdymJUF/RVNNvDlZbaLdd
K8vDEi92eRwcf07a5b/Q2F8yNfADKKmRAA/oAbuQLBhJ0dPHig70PIvi9gq9kqiE
Ft1MinbsZLavYatLm7oVDr/nsYebEDMGwTy0EX5bF2YjydfAlCvVWnI5ld5wisiV
0fQF4W7MMjjcpAzG8uq3atEB8iQcWS2Ykz2chZRbYzHcdV2WJW751Vge9xc05Hzi
rxlqn6peZFiFyM0qdPLhY0ktGzSTZcCFeb3aZicvm5aOamy2KJjOSZrEwjU8kts=
=VHpx
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc1' into fixes
We've received a few fixes branches with -rc1 as base, but our contents was
still at pre-rc1. Merge it in expliticly to make 'git merge --log' clear on
hat was actually merged.
Signed-off-by: Olof Johansson <olof@lixom.net>
Add secondary pinctrl set for UART2 which can be used to prevent conflicts
with sdmmc pins.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Correct UART2 PINCTRL flag to use the correct pull up setting
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Refer to Chapter 5.3.2 of rk3229 TRM, we can see that GPIO1A[2,4,5]
using RK_FUNC_2 not RK_FUNC_1. This patch fixes it.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On dra7, as per TRM, the HW shutdown (TSHUT) temperature is hardcoded
to 123C and cannot be modified by SW. This means when the temperature
reaches 123C HW asserts TSHUT output which signals a warm reset.
This reset is held until the temperature goes below the TSHUT low (105C).
While in SW, the thermal driver continuously monitors current temperature
and takes decisions based on whether it reached an alert or a critical point.
The intention of setting a SW critical point is to prevent force reset by HW
and instead do an orderly_poweroff(). But if the SW critical temperature is
greater than or equal to that of HW then it defeats the purpose. To address
this and let SW take action before HW does keep the SW critical temperature
less than HW TSHUT value.
The value for SW critical temperature was chosen as 120C just to ensure
we give SW sometime before HW catches up.
Document reference
SPRUI30C – DRA75x, DRA74x Technical Reference Manual - November 2016
SPRUHZ6H - AM572x Technical Reference Manual - November 2016
Tested on:
DRA75x PG 2.0 Rev H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds a new node to the LEGO MINDSTORMS EV3 device tree for the battery.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: minor headline fix]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
If we have Linux installed in eMMC we can boot without
µSD card, but inserting one is not recognised.
The reason is that the card detect gpio (gpio5_152)
is not configured and attached to the mmc1 interface
driver and the mmc driver does not poll by default.
Hence we add pinmux and gpio setup for the SDCARD_NCD
signal.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Droid 4 has WL 1285C connected to the OMAP's UART4 port, which is
used for Bluetooth and most likely can also be used for controlling
the FM radio and GPS receivers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB1 port is micro-AB type and can function as peripheral
as well as host. Enable dual-role mode for USB1.
We don't want to use the OTG controller block on this
platform as it limits host mode to high-speed. Instead
we rely on extcon framework to give us ID events for
dual-role mode detection.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
