This patch extends DAPM routing and adds secondary CPU DAI entry
to support the secondary audio PCM interface on Odroid XU4.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch extends DAPM routing and adds secondary CPU DAI entry
to support the secondary audio PCM interface on Odroid XU3.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
ARM Performance Monitoring Units (PMUs) are permanently disabled in the
Exynos5422 SoC version used on Odroid XU3-lite boards. Disable them in
boards dtb to avoid confusing user and getting following warning on boot:
hw-breakpoint: Failed to enable monitor mode on CPU 0
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace bootargs and kernel console parameter with 'stdout-path' property
in 'chosen' node to instruct kernel which serial driver should be used
for the kernel console and logs. This allows to enable earlycon messages
by adding just 'earlycon' parameter to kernel command line.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add minimal parameters needed by the Exynos CLKOUT driver to Exynos3250
PMU node. This fixes the following warning on boot:
exynos_clkout_init: failed to register clkout clock
Fixes: d19bb397e1 ("ARM: dts: exynos: Update PMU node with CLKOUT related data")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Odroid HC1 uses the exynos5422-odroid-core.dtsi file as a base. All
other Exynos5422 Odroids use the "common". The ADC node was defined
only in the latter.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commit 225da7e65a ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7c ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org>
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 225da7e65a ("ARM: dts: add eMMC reset line for exynos4412-odroid-common")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
LDO20 regulator provides power for the MMC card on Odroid U3 boards. That
regulator has been marked as 'boot-on' since the beginning of Odroid X/U3
support, but such flag is not really needed for it. That regulator is
correctly described as supply for eMMC card and controlled by its driver.
Commit 05f224ca66 ("regulator: core: Clean enabling always-on regulators
+ their supplies") changed the way the boot-on regulators are handled and
since then regulators marked as 'boot-on' got increased reference count
and are not turned off for the system suspend time.
The new approach turned out to break suspend/resume support on Odroid U3
with eMMC card, because the card is not properly shutdown due to missing
of power cycle. Fix this by removing excessive 'boot-on' flag and let
MMC driver to control turning power on and off.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Bindings of the fixed-regulator, which precedes support for GPIO flags
passed via phandle descriptor, introduced its own method annotating
that the given GPIO line is active low or high - by using
'enable-active-high' property. The driver always ignored flags passed
via GPIO descriptor.
Fix the conflicting GPIO flags to match the status forced by the
'enable-active-high' property to avoid future confusion.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix the DTC warning for xti node:
arch/arm/boot/dts/s3c2416-smdk2416.dts:23.12-28.5:
Warning (simple_bus_reg): /clocks/xti: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
According to Devicetree specification, the unit-address must match the
first address specified in the reg property of the node. Fix the DTC
warning onenand node:
arch/arm/boot/dts/s5pv210.dtsi:81.29-93.5:
Warning (simple_bus_reg): /soc/onenand@b0000000: simple-bus unit address format error, expected "b0600000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
This commit adds DMC (Dynamic Memory Controller) nodes, which are needed
by S5Pv210 cpufreq driver to work.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This commit enables following devices present on Aries based phones:
- pwm-vibrator attached to PWM 1
- poweroff support
- Atmel maXTouch touchscreen, connected to I2C-2
- Broadcom BCM4329 Bluetooth over UART-0
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
THis commit adds memory reservation required by MFC (Multi Format Codec)
to run. On S5PV210 both regions needs to be on separate memory banks.
Size of both regions is taken from vendor Linux kernel sources.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since we have U-Boot (flashed in place of stock kernel), it's not needed
anymore to hardcode bootargs on every Aries-family board.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
[krzk: Squash changes to fascinate4g and galaxys into one commit]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since we have separate compatible for S5Pv210 FIMD, let's use it rather
than using one from Exynos4210.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add node for Exynos Rorator device, so it can be used on all S5Pv210
based devices.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not implement
mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I+r6
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Since commit 9c2af1c737 ("kbuild: add .DELETE_ON_ERROR special
target"), the target file is automatically deleted on failure.
The boilerplate code
... || { rm -f $@; false; }
is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a build
fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated Vivante
GPU, 256MB RAM, Wifi). This includes some acked platform-specific
drivers (serial, etc). This also include DTs for two boards with this
SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs.
-----BEGIN PGP SIGNATURE-----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=qgZw
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
- Florian Fainelli noticed that userspace segfaults caused by the lack
of kernel-userspace helpers was hard to diagnose; we now issue a
warning when userspace tries to use the helpers but the kernel has
them disabled.
- Ben Dooks wants compatibility for the old ATAG serial number with DT
systems.
- Some cleanup of assembly by Nicolas Pitre.
- User accessors optimisation from Vincent Whitchurch.
- More robust kdump on SMP systems from Yufen Wang.
- Sebastian Andrzej Siewior noticed problems with the SMP "boot_lock"
on RT kernels, and so we convert the Versatile series of platforms
to use a raw spinlock instead, consolidating the Versatile
implementation. We entirely remove the boot_lock on OMAP systems,
where it's unnecessary. Further patches for other systems will be
submitted for the following merge window.
- Start switching old StrongARM-11x0 systems to use gpiolib rather
than their private GPIO implementation - mostly PCMCIA bits.
- ARM Kconfig cleanups.
- Cleanup a mostly harmless mistake in the recent Spectre patch in 4.20
(which had the effect that data that can be placed into the init
sections was incorrectly always placed in the rodata section.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Yl96
-----END PGP SIGNATURE-----
Merge tag 'for-4.21' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
"Included in this update:
- Florian Fainelli noticed that userspace segfaults caused by the
lack of kernel-userspace helpers was hard to diagnose; we now issue
a warning when userspace tries to use the helpers but the kernel
has them disabled.
- Ben Dooks wants compatibility for the old ATAG serial number with
DT systems.
- Some cleanup of assembly by Nicolas Pitre.
- User accessors optimisation from Vincent Whitchurch.
- More robust kdump on SMP systems from Yufen Wang.
- Sebastian Andrzej Siewior noticed problems with the SMP "boot_lock"
on RT kernels, and so we convert the Versatile series of platforms
to use a raw spinlock instead, consolidating the Versatile
implementation. We entirely remove the boot_lock on OMAP systems,
where it's unnecessary. Further patches for other systems will be
submitted for the following merge window.
- Start switching old StrongARM-11x0 systems to use gpiolib rather
than their private GPIO implementation - mostly PCMCIA bits.
- ARM Kconfig cleanups.
- Cleanup a mostly harmless mistake in the recent Spectre patch in
4.20 (which had the effect that data that can be placed into the
init sections was incorrectly always placed in the rodata section)"
* tag 'for-4.21' of git://git.armlinux.org.uk/~rmk/linux-arm: (25 commits)
ARM: omap2: remove unnecessary boot_lock
ARM: versatile: rename and comment SMP implementation
ARM: versatile: convert boot_lock to raw
ARM: vexpress/realview: consolidate immitation CPU hotplug
ARM: fix the cockup in the previous patch
ARM: sa1100/cerf: switch to using gpio_led_register_device()
ARM: sa1100/assabet: switch to using gpio leds
ARM: sa1100/assabet: add gpio keys support for right-hand two buttons
ARM: sa1111: remove legacy GPIO interfaces
pcmcia: sa1100*: remove redundant bvd1/bvd2 setting
ARM: pxa/lubbock: switch PCMCIA to MAX1600 library
ARM: pxa/mainstone: switch PCMCIA to MAX1600 library and gpiod APIs
ARM: sa1100/neponset: switch PCMCIA to MAX1600 library and gpiod APIs
ARM: sa1100/jornada720: switch PCMCIA to gpiod APIs
pcmcia: add MAX1600 library
ARM: sa1100: explicitly register sa11x0-pcmcia devices
ARM: 8813/1: Make aligned 2-byte getuser()/putuser() atomic on ARMv6+
ARM: 8812/1: Optimise copy_{from/to}_user for !CPU_USE_DOMAINS
ARM: 8811/1: always list both ldrd/strd registers explicitly
ARM: 8808/1: kexec:offline panic_smp_self_stop CPU
...
As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a fragment,
that later gets filled in on later releases, and in some cases it's
near-complete platform support. The latter is more common for derivative
platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions. Allwinner
support for F1C100s, a quite old SoC (ARMv5-based) shipping in the
Lychee Pi Nano platform. At the other end is NXP Layerscape LX2160A,
a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O aimed at
infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to devicetree,
which opens up for removal of even more of their platform-specific
'hwmod' description tables over the next few releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board
-----BEGIN PGP SIGNATURE-----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=sFVi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug console setups
- SoCFPGA adds explicit selection of ARM errata and removes some unused code
This tag also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release.
-----BEGIN PGP SIGNATURE-----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=m7me
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
-----BEGIN PGP SIGNATURE-----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=dIrg
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Samsung DTS ARM changes for v4.21, part 2
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
* tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
ARM: dts: exynos: remove display-port node from Arndale
ARM: dts: exynos: Add opp-suspend to DMC and leftbus devfreq OPPs on Exynos4
ARM: dts: s5pv210: Add s5p-jpeg codec node.
ARM: dts: exynos: Use Samsung SoC specific compatible for DWC2 module
ARM: dts: exynos: Add all CPUs in cooling maps
ARM: dts: exynos: Clarify comment explaining purpose of Odroid XU3 DTSI
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4/HC1
ARM: dts: exynos: Update maximum frequency for eMMC to 200MHz on Odroid XU3/XU4
ARM: dts: exynos: Update maximum frequency for SD card to 200MHz on Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix LDO13 min values on Odroid XU3/XU4/HC1
ARM: dts: exynos: Add UHS-I bus speed support to Odroid XU3/XU4/HC1
ARM: dts: exynos: Add missing clocks to RTC node for Arndale board
ARM: dts: exynos: Add compatible for s5m8767 clocks node on Itop Core
ARM: dts: exynos: Add compatible for s2mps11 clocks node on Exynos542x
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial devicetree for Orange Pi i96 board from Xunlong. It
is one of the 96Boards IoT Edition board.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable per-task stack protector for ARM (Ard Biesheuvel)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=AkLm
-----END PGP SIGNATURE-----
Merge tag 'gcc-plugins-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc-plugins update from Kees Cook:
"Both arm and arm64 are gaining per-task stack canaries (to match x86),
but arm is being done with a gcc plugin, hence it going through the
gcc-plugins tree.
New gcc-plugin:
- Enable per-task stack protector for ARM (Ard Biesheuvel)"
* tag 'gcc-plugins-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
ARM: smp: add support for per-task stack canaries
This is a small pull request for some lingering things that didn't make
the first round of patches.
First, the new suniv device tree included device tree headers for the
clock and reset indices. These header filers are going in through the
clock tree. Thus with the dt and core branches in arm-soc alone, it
doesn't build. One fix is included to remove the #include statements.
The defined macros aren't used yet as they were properly removed during
the review phase.
Second, Bluetooth using Broadcom (now Cypress) chips connected to UARTs
on various boards is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
-----BEGIN PGP SIGNATURE-----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=FiER
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.21 - round 2
This is a small pull request for some lingering things that didn't make
the first round of patches.
First, the new suniv device tree included device tree headers for the
clock and reset indices. These header filers are going in through the
clock tree. Thus with the dt and core branches in arm-soc alone, it
doesn't build. One fix is included to remove the #include statements.
The defined macros aren't used yet as they were properly removed during
the review phase.
Second, Bluetooth using Broadcom (now Cypress) chips connected to UARTs
on various boards is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
* tag 'sunxi-dt-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
ARM: dts: suniv: Fix improper bindings include patch
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- It contains a series from Schrempf Frieder that cleans up FSL QSPI
device tree nodes. The current device trees are broken because they
use an inconsistent scheme for assigning the reg properties. It
becomes a problem with ongoing QSPI driver under SPI framework. So
the cleanup is a preparation for new driver landing in the next
cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcFg+pAAoJEFBXWFqHsHzOC3UH/RsA0ysBXsaUF9aNpfmwFpKP
bApnoyo+MhLZSvFqD8eU1K0BhXFOkOmMXMbTle0b3uF7qaknnXEoWTCNz+hJGDsz
fFeOqz7xjyG8Q4U8PT4ImG0OPuFNNGBs1byJKZygxJp/xBlAGMKDp/rRKbM4c8+8
WzoKcWcLqFe+Vau0vuesjcT7J/B3nWvzOWsWX5MHOp10rEWyv9Y4Ct3cAzSMVhAM
1eLQpYegOvUckX0if7BZpj7vSIhDNp/urx6U7D5KGAf9iHK50euMX55LhveiSM8w
CdnnZn2MUXEt2A81Aqb97IOhMsEra47Ffomr1nIV2OGbmDY27HrlUrNSEKNER28=
=I3dR
-----END PGP SIGNATURE-----
Merge tag 'imx-qspi-dt-clean' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Freescale QSPI device tree cleanup for 4.21:
- It contains a series from Schrempf Frieder that cleans up FSL QSPI
device tree nodes. The current device trees are broken because they
use an inconsistent scheme for assigning the reg properties. It
becomes a problem with ongoing QSPI driver under SPI framework. So
the cleanup is a preparation for new driver landing in the next
cycle.
* tag 'imx-qspi-dt-clean' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The clock and reset bindings are going through different trees, and while
the patch doesn't contain any value defined in that header, it still
includes those files and result in a build breakage when building the DT
without the matching clock and reset patches applied.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This big set of changes adds SoC specific l4 interconnect target module
device tree data for am335x, am437x, omap5 and dra7 SoCs. We also move
existing devices to the right location in the l4 interconnect hierarcy.
This is similar to what we've already done for omap4 l4 interconnects
earlier, and follows what is documented in the ti-sysc driver dts binding
in Documentation/devicetree/bindings/bus/ti-sysc.txt.
These changes will essentially replace the struct ti_sysc and clock
entries in the arch/arm/mach-omap2/omap_hwmod_*_data.c files. Then a few
merge windows later, we can start dropping the built-in platform data
from the omap_hwmod_*_data.c files in favor of the device tree data only.
For now, we verify the device tree data module data against the built-in
data and warn about changes to prevent regressions.
With the device tree data, we are also probing devices with the ti-sysc
interconnect target module instead of omap_device. This fixes up the
handling for multiple device instances in a single interconnect target
module that has caused trouble earlier. A custom wrapper driver has been
needed earlier for such cases.
And as the device tree data is organized by the l4 interconnect instances,
we will be able to use genpd later on. This is because each interconnect
instance is also often also a single power domain.
This series of changes has been brewing for several months now. I did not
want to send a pull request earlier as people were still seeing device
specific issues until recently though. However, it turned out that all the
issues were quite trivial to fix. I had missed adding device tree ranges
for the l3 data port used on some devices, and I had missed converting the
device addresses for a few devices. And some devices like needed fixes for
deferred probe handling such as the EHCI PHY for built-in case on omap5.
Anyways, in case of trouble, we can easily just revert changes for a
single device if needed.
-----BEGIN PGP SIGNATURE-----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=9lDj
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.21/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Add interconnect target module dts data for omaps for v4.21
This big set of changes adds SoC specific l4 interconnect target module
device tree data for am335x, am437x, omap5 and dra7 SoCs. We also move
existing devices to the right location in the l4 interconnect hierarcy.
This is similar to what we've already done for omap4 l4 interconnects
earlier, and follows what is documented in the ti-sysc driver dts binding
in Documentation/devicetree/bindings/bus/ti-sysc.txt.
These changes will essentially replace the struct ti_sysc and clock
entries in the arch/arm/mach-omap2/omap_hwmod_*_data.c files. Then a few
merge windows later, we can start dropping the built-in platform data
from the omap_hwmod_*_data.c files in favor of the device tree data only.
For now, we verify the device tree data module data against the built-in
data and warn about changes to prevent regressions.
With the device tree data, we are also probing devices with the ti-sysc
interconnect target module instead of omap_device. This fixes up the
handling for multiple device instances in a single interconnect target
module that has caused trouble earlier. A custom wrapper driver has been
needed earlier for such cases.
And as the device tree data is organized by the l4 interconnect instances,
we will be able to use genpd later on. This is because each interconnect
instance is also often also a single power domain.
This series of changes has been brewing for several months now. I did not
want to send a pull request earlier as people were still seeing device
specific issues until recently though. However, it turned out that all the
issues were quite trivial to fix. I had missed adding device tree ranges
for the l3 data port used on some devices, and I had missed converting the
device addresses for a few devices. And some devices like needed fixes for
deferred probe handling such as the EHCI PHY for built-in case on omap5.
Anyways, in case of trouble, we can easily just revert changes for a
single device if needed.
* tag 'omap-for-v4.21/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Cosmetic fix for omap5 USB node names
ARM: dts: Fix wrong address for omap5 sata phy
ARM: dts: Add missing ranges for dra7 mcasp l3 ports
ARM: dts: Fix ranges for am335x epwmss
ARM: dts: Fix hsi gdd range for omap4
ARM: dts: Add am335x mcasp with l3 data port ranges
ARM: dts: Add missing ranges for am437x mcasp l3 ports
ARM: dts: dra7: Move the ti,no-idle quirk on proper gmac node
ARM: dts: Revert am335x mcasp ti-sysc changes
ARM: dts: omap5: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: Use dra7 mcasp compatible for mcasp instances
ARM: dts: dra7: Move l4 child devices to probe them with ti-sysc
ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: am335x: Move l4 child devices to probe them with ti-sysc
ARM: dts: am335x: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: am437x: Move l4 child devices to probe them with ti-sysc
ARM: dts: am437x: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: dra7: convert to use new clkctrl layout
ARM: dts: am43xx: convert to use new clkctrl layout
ARM: dts: am33xx: convert to use new clkctrl layout
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the Bluetooth node, and the underlying UART node if it's
missing, to the board device tree file for several boards. The LPO clock
is also added to the WiFi side's power sequencing node if it's missing,
to correctly represent the shared connections. There is also a PCM
connection for Bluetooth, but this is not covered in this patch.
These boards all have a WiFi+BT module from AMPAK, which contains one or
two Broadcom chips, depending on the model. The older AP6210 contains
two, while the newer AP6212 and AP6330 contain just one, as they use
two-in-one combo chips.
The Bluetooth side of the module is always connected to a UART on the
same pingroup as the SDIO pins for the WiFi side, in a 4 wire
configuration. Power to the VBAT and VDDIO pins are provided either by
the PMIC, using one or several of its regulator outputs, or other fixed
regulators on the board. The VBAT and VDDIO pins are shared with the
WiFi side, which would correspond to vmmc-supply and vqmmc-supply in the
mmc host node. A clock output from the SoC or the external X-Powers RTC
provides the LPO low power clock at 32.768 kHz.
All the boards covered in this patch are ones that do not require extra
changes to the SoC's dtsi file. For the remaining boards that I have
worked on, properties or device nodes for the LPO clock's source are
missing.
For the Cubietruck, the LPO clock is fed from CLK_OUT_A, which needs to
be muxed on pin PI12. This can be represented in multiple ways. This
patch puts the pinctrl property in the pin controller node. This is due
to limitations in Linux, where pinmux settings, even the same one, can
not be shared by multiple devices. Thus we cannot put it in both the
WiFi and Bluetooth device nodes. Putting it the CCU node is another
option, but Linux's CCU driver does not handle pinctrl. Also the pin
controller is guaranteed to be initialized after the CCU, when clocks
are available. And any other devices that use muxed pins are guaranteed
to be initialized after the pin controller. Thus having the CLK_OUT_A
pinmux reference be in the pin controller node is a good choice without
having to deal with implementation issues.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The clock and reset bindings are going through different trees, and while
the patch doesn't contain any value defined in that header, it still
includes those files and result in a build breakage when building the DT
without the matching clock and reset patches applied.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The "num-lanes" property for PCIe is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
We will move the FSL QSPI driver to the SPI framework soon. To
prepare and to make sure the full buswidth is used (as it is with
the current driver), let's add the right properties.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current driver does not use the reg properties, but we will
add a new driver soon. To make sure we have a consistent scheme,
let's fix the reg properties here.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The properties 'bus-num', 'fsl,spi-num-chipselects' and
'fsl,spi-flash-chipselects' were never read by the driver
and can be removed.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The assigned parent clocks should be normally specified in the consumer
device's DT node, this ensures respective driver always sees correct clock
settings when required.
This patch fixes regression in audio subsystem on Odroid XU3/XU4 boards
that appeared after commits:
commit 647d04f8e0 ("ASoC: samsung: i2s: Ensure the RCLK rate is properly determined")
commit 995e73e55f ("ASoC: samsung: i2s: Fix rclk_srcrate handling")
commit 48279c53fd ("ASoC: samsung: i2s: Prevent external abort on exynos5433 I2S1 access")
Without this patch the driver gets wrong clock as the I2S function clock
(op_clk) in probe() and effectively the clock which is finally assigned
from DT is not being enabled/disabled in the runtime resume/suspend ops.
Without the above listed commits the EXYNOS_I2S_BUS clock was always set
as parent of CLK_I2S_RCLK_SRC regardless of DT settings so there was no issue
with not enabled EXYNOS_SCLK_I2S.
Cc: <stable@vger.kernel.org> # 4.17.x
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
While updating cooling maps, the exynos4412-prime.dtsi was left
untouched. This is not a problem with Odroid U3 because it uses its own
map with fan (which was updated). However the cooling maps of Odroid X2
rely only on exynos4412-prime.dtsi.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
These should be now using offset from the module base and not the
full physical address.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OLinuXino Lime2 has a big capacitor on its LDO3 output. It is
actually too large, causing the PMIC to shutdown when toggling the LDO3.
By enabling soft-start and ramp delay we increase the time for the
capacitor to charge lowering the current drain on the power regulator.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like I missed converting the omap5 sata phy addresses to use offset
from the module base instead of full physical address.
While at it, we can also more it to be a direct child of the interconnect
target module, it is not really a child of the ocp2scp control device.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here's a collection of minor fixes for annoying usability issues
people have noticed using various devices.
There are two regression fixes:
- A regression fix for omap5 usb3 dual role mode
- A regression fix to ams-delta audio being muted permanently
And two one-liners:
- Fix polarity for am335x-pdu001 SD card detection
- Fix non-working omap4-sdp Ethernet startup for rebind
It would be nice to get these merged during the -rc cycle if
possible. Naturally these can all wait for the merge window too
if we start running out of time.
-----BEGIN PGP SIGNATURE-----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=mhE2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.20/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few device fixes for omaps
Here's a collection of minor fixes for annoying usability issues
people have noticed using various devices.
There are two regression fixes:
- A regression fix for omap5 usb3 dual role mode
- A regression fix to ams-delta audio being muted permanently
And two one-liners:
- Fix polarity for am335x-pdu001 SD card detection
- Fix non-working omap4-sdp Ethernet startup for rebind
It would be nice to get these merged during the -rc cycle if
possible. Naturally these can all wait for the merge window too
if we start running out of time.
* tag 'omap-for-v4.20/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
Signed-off-by: Olof Johansson <olof@lixom.net>
