Daniel Vetter writes:
A new drm-intel-next pull. Highlights:
- More gmbus patches from Daniel Kurtz, I think gmbus is now ready, all
known issues fixed.
- Fencing cleanup and pipelined fencing removal from Chris.
- rc6 residency interface from Ben, useful for powertop.
- Cleanups and code reorg around the ringbuffer code (Ben&me).
- Use hw semaphores in the pageflip code from Ben.
- More vlv stuff from Jesse, unfortunately his vlv cpu is doa, so less
merged than I've hoped for - we still have the unused function warning :(
- More hsw patches from Eugeni, again, not yet enabled fully.
- intel_pm.c refactoring from Eugeni.
- Ironlake sprite support from Chris.
- And various smaller improvements/fixes all over the place.
Note that this pull request also contains a backmerge of -rc3 to sort out
a few things in -next. I've also had to frob the shortlog a bit to exclude
anything that -rc3 brings in with this pull.
Regression wise we have a few strange bugs going on, but for all of them
closer inspection revealed that they've been pre-existing, just now
slightly more likely to be hit. And for most of them we have a patch
already. Otherwise QA has not reported any regressions, and I'm also not
aware of anything bad happening in 3.4.
* tag 'drm-intel-next-2012-04-23' of git://people.freedesktop.org/~danvet/drm-intel: (420 commits)
drm/i915: rc6 residency (fix the fix)
drm/i915/tv: fix open-coded ARRAY_SIZE.
drm/i915: invalidate render cache on gen2
drm/i915: Silence the change of LVDS sync polarity
drm/i915: add generic power management initialization
drm/i915: move clock gating functionality into intel_pm module
drm/i915: move emon functionality into intel_pm module
drm/i915: move drps, rps and rc6-related functions to intel_pm
drm/i915: fix line breaks in intel_pm
drm/i915: move watermarks settings into intel_pm module
drm/i915: move fbc-related functionality into intel_pm module
drm/i915: Refactor get_fence() to use the common fence writing routine
drm/i915: Refactor fence clearing to use the common fence writing routine
drm/i915: Refactor put_fence() to use the common fence writing routine
drm/i915: Prepare to consolidate fence writing
drm/i915: Remove the unsightly "optimisation" from flush_fence()
drm/i915: Simplify fence finding
drm/i915: Discard the unused obj->last_fenced_ring
drm/i915: Remove unused ring->setup_seqno
drm/i915: Remove fence pipelining
...
All supported devices have one issue that msi interrupt doesn't assert
if pci command register bit (PCI_COMMAND_INTX_DISABLE) is set.
Add workaround in drivers/pci/quirks.c
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intent of git commit 6fbf9e7a90
"PCI: Introduce __pci_reset_function_locked to be used when holding
device_lock." was to have a non-locking function that would call
pci_dev_reset function.
But it fell short of that by just probing and not actually reseting
the device. To make that work we need a way to move the lock
around device_lock to not be in pci_dev_reset (as the caller of
__pci_reset_function_locked already holds said lock). We do this by
renaming pci_dev_reset to __pci_dev_reset and bubbling said mutex out
of __pci_dev_reset to pci_dev_reset (a wrapper around __pci_dev_reset).
The __pci_reset_function_locked can now call __pci_dev_reset without
having to worry about the dead-lock.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A PCIe downstream port is a P2P bridge. Its secondary interface is
a link that should lead only to device 0 (unless ARI is enabled)[1], so
we don't probe for non-zero device numbers.
Some Stratus ftServer systems have a PCIe downstream port (02:00.0) that
leads to both an upstream port (03:00.0) and a downstream port (03:01.0),
and 03:01.0 has important devices below it:
[0000:02]-+-00.0-[03-3c]--+-00.0-[04-09]--...
\-01.0-[0a-0d]--+-[USB]
+-[NIC]
+-...
Previously, we didn't enumerate device 03:01.0, so USB and the network
didn't work. This patch adds a DMI quirk to scan all device numbers,
not just 0, below a downstream port.
Based on a patch by Prarit Bhargava.
[1] PCIe spec r3.0, sec 7.3.1
CC: Myron Stowe <mstowe@redhat.com>
CC: Don Dutile <ddutile@redhat.com>
CC: James Paradis <james.paradis@stratus.com>
CC: Matthew Wilcox <matthew.r.wilcox@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need a hook to release host bridge resources allocated when creating
root bus.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use that device for pci_root_bus bridge pointer.
Use pci_release_bus_bridge_dev() to release allocated pci_host_bridge in
remove path.
Use root bus bridge pointer to get host bridge pointer instead of searching
host bridge list. That leaves the host bridge list unused, so remove it.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_host_bridge() looks like a C++ constructor. Also separate
find_pci_root_bus() out.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move host bridge-related code from probe.c to a new host-bridge.c.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull build fixes for less mainstream architectures from Paul Gortmaker:
"These are fixes for frv(1), blackfin(2), powerpc(1) and xtensa(4).
Fortunately the touches are nearly all specific to files just used by
the arch in question. The two touches to shared/common files
[kernel/irq/debug.h and drivers/pci/Makefile] are trivial to assess as
no risk to anyone.
Half of them relate to xtensa directly. It was only when I fixed the
last xtensa issue that I realized that the arch has been broken for a
significant time, and isn't a specific v3.4 regression. So if you
wanted, we could leave xtensa lying bleeding in the street for a
couple more weeks and queue those for 3.5. But given they are no risk
to anyone outside of xtensa, I figured to just leave them in.
If you are OK with taking the xtensa fixes, then please pull to get:
- one last implicit include uncovered by system.h that is in a file
specific to just one powerpc defconfig. (I'd sync'd with BenH).
- fix an oversight in the PCI makefile where shared code wasn't being
compiled for ARCH=frv
- fix a missing include for GPIO in blackfin framebuffer.
- audit and tag endif in blackfin ezkit board file, in order to find
and fix the misplaced endif masking a block of code.
- fix irq/debug.h choice of temporary macro names to be more internal
so they don't conflict with names used by xtensa.
- fix a reference to an undeclared local var in xtensa's signal.c
- fix an implicit bug.h usage in xtensa's asm/io.h uncovered by my
removing bug.h from kernel.h
- fix xtensa to properly indicate it is using asm-generic/hardirq.h
in order to resolve the link error - undefined ack_bad_irq
The xtensa still fails final link as my latest binutils does something
evil when ld forward-relocates unlikely() blocks, but in theory people
who have older/valid toolchains could now use the thing."
* 'for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
xtensa: fix build fail on undefined ack_bad_irq
blackfin: fix ifdef fustercluck in mach-bf538/boards/ezkit.c
blackfin: fix compile error in bfin-lq035q1-fb.c
pci: frv architecture needs generic setup-bus infrastructure
irq: hide debug macros so they don't collide with others.
xtensa: fix build error in xtensa/include/asm/io.h
xtensa: fix build failure in xtensa/kernel/signal.c
powerpc: fix system.h fallout in sysdev/scom.c [chroma_defconfig]
Otherwise we get this link failure for frv's defconfig:
LD .tmp_vmlinux1
drivers/built-in.o: In function `pci_assign_resource':
(.text+0xbf0c): undefined reference to `pci_cardbus_resource_alignment'
drivers/built-in.o: In function `pci_setup':
pci.c:(.init.text+0x174): undefined reference to `pci_realloc_get_opt'
pci.c:(.init.text+0x1a0): undefined reference to `pci_realloc_get_opt'
make[1]: *** [.tmp_vmlinux1] Error 1
Cc: David Howells <dhowells@redhat.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The default VGA device is a somewhat fluid concept on platforms with
multiple GPUs. Add support for setting it so switching code can update
things appropriately, and make sure that the sysfs code returns the right
device if it's changed.
v2: Updated to fix builds when __ARCH_HAS_VGA_DEFAULT_DEVICE is false.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: benh@kernel.crashing.org
Cc: airlied@redhat.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some shortcomings introduced into pci_restore_state() by commit
26f41062f2 ("PCI: check for pci bar restore completion and retry")
have been fixed by recent commit ebfc5b802f ("PCI: Fix regression in
pci_restore_state(), v3"), but that commit treats all PCI devices as
those with Type 0 configuration headers.
That is not entirely correct, because Type 1 and Type 2 headers have
different layouts. In particular, the area occupied by BARs in Type 0
config headers contains the secondary status register in Type 1 ones and
it doesn't make sense to retry the restoration of that register even if
the value read back from it after a write is not the same as the written
one (it very well may be different).
For this reason, make pci_restore_state() only retry the restoration
of BARs for Type 0 config headers. This effectively makes it behave
as before commit 26f41062f2 for all header types except for Type 0.
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 26f41062f2 ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.
First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one). Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt. Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.
All of this actually caused resume failures for some devices on Mikko's
system.
To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value. Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* one is a workaround that will be removed in v3.5 with proper fix in the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made them only
load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup in the
core code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPfyVUAAoJEFjIrFwIi8fJUjUH/jbY5JavRqSlNELZW2A4Ta76
8p00LqLHw/C56iHZcWKke8mqtWNb+ZfcQt7ZYcxDIYa4QWBL28x0OLAO2tOBIt37
ZjYESWSdFJaJvmpADluWtFyGyZ9TYJllDTBm/jWj1ZtKSZvR1YkhuMXCS0f4AmGQ
xFzSWJZUDdiOAqpN+VQD8wP00gfR8knQLg16XE2fvFdQo4XwpCtqLfHV/5pMMGdy
Cs/ep6rq/7cdv/nshKOcBnw7RW8l3Xoi/28ht8k3DvAQ2VtFq1Tugv2G9pcCHwQG
DIBkB3SOU6/v6P5at5+egKS5xR1fJetCWlkMd8kkbcdz2NPI4UDMkvOW6Q8yQls=
=6Ve+
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes for regressions:
* one is a workaround that will be removed in v3.5 with proper fix in
the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made
them only load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup
in the core code."
* tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pcifront: avoid pci_frontend_enable_msix() falsely returning success
xen/pciback: fix XEN_PCI_OP_enable_msix result
xen/smp: Remove unnecessary call to smp_processor_id()
xen/x86: Workaround 'x86/ioapic: Add register level checks to detect bogus io-apic entries'
xen: only check xen_platform_pci_unplug if hvm
The original XenoLinux code has always had things this way, and for
compatibility reasons (in particular with a subsequent pciback
adjustment) upstream Linux should behave the same way (allowing for two
distinct error indications to be returned by the backend).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since 3.2.12 and 3.3, some systems are failing to boot with a BUG_ON.
Some other systems using the pata_jmicron driver fail to boot because no
disks are detected. Passing pcie_aspm=force on the kernel command line
works around it.
The cause: commit 4949be1682 ("PCI: ignore pre-1.1 ASPM quirking when
ASPM is disabled") changed the behaviour of pcie_aspm_sanity_check() to
always return 0 if aspm is disabled, in order to avoid cases where we
changed ASPM state on pre-PCIe 1.1 devices.
This skipped the secondary function of pcie_aspm_sanity_check which was
to avoid us enabling ASPM on devices that had non-PCIe children, causing
trouble later on. Move the aspm_disabled check so we continue to honour
that scenario.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=42979 and
http://bugs.debian.org/665420
Reported-by: Romain Francoise <romain@orebokech.com> # kernel panic
Reported-by: Chris Holland <bandidoirlandes@gmail.com> # disk detection trouble
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Tested-by: Hatem Masmoudi <hatem.masmoudi@gmail.com> # Dell Latitude E5520
Tested-by: janek <jan0x6c@gmail.com> # pata_jmicron with JMB362/JMB363
[jn: with more symptoms in log message]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ACPI & Power Management changes from Len Brown:
- ACPI 5.0 after-ripples, ACPICA/Linux divergence cleanup
- cpuidle evolving, more ARM use
- thermal sub-system evolving, ditto
- assorted other PM bits
Fix up conflicts in various cpuidle implementations due to ARM cpuidle
cleanups (ARM at91 self-refresh and cpu idle code rewritten into
"standby" in asm conflicting with the consolidation of cpuidle time
keeping), trivial SH include file context conflict and RCU tracing fixes
in generic code.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (77 commits)
ACPI throttling: fix endian bug in acpi_read_throttling_status()
Disable MCP limit exceeded messages from Intel IPS driver
ACPI video: Don't start video device until its associated input device has been allocated
ACPI video: Harden video bus adding.
ACPI: Add support for exposing BGRT data
ACPI: export acpi_kobj
ACPI: Fix logic for removing mappings in 'acpi_unmap'
CPER failed to handle generic error records with multiple sections
ACPI: Clean redundant codes in scan.c
ACPI: Fix unprotected smp_processor_id() in acpi_processor_cst_has_changed()
ACPI: consistently use should_use_kmap()
PNPACPI: Fix device ref leaking in acpi_pnp_match
ACPI: Fix use-after-free in acpi_map_lsapic
ACPI: processor_driver: add missing kfree
ACPI, APEI: Fix incorrect APEI register bit width check and usage
Update documentation for parameter *notrigger* in einj.txt
ACPI, APEI, EINJ, new parameter to control trigger action
ACPI, APEI, EINJ, limit the range of einj_param
ACPI, APEI, Fix ERST header length check
cpuidle: power_usage should be declared signed integer
...
acpi_dev_run_wake() is a generic function which can be used by
other subsystem too. Rename it to acpi_pm_device_run_wake, to be
consistent with acpi_pm_device_sleep_wake.
Then move it to ACPI core.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
- PV multiconsole support, so that there can be hvc1, hvc2, etc;
- P-state and C-state power management driver that uploads said
power management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPZ0qkAAoJEFjIrFwIi8fJjCgH/jeJ39E8ML8DP9tCS2HQnMqM
uTEjLcqvoJ7sEhHvtBLPeG2p0jyBvOWjLbSc7P8nESBAMPvSYol8L6WqfWrdSU4r
lHrma2sg9UYzRog5NyxAgkp7bBsBBFOnhVL3Cxb5Ig78cPWzeSWGpqGZ8M/d51Wf
1iE0tHuU4DpN+fg1SZqPqEm8ecEJ/eSrVTnyTx/Qo2Ak+Zw98SqzX7SV5lo8mudd
WFL1F2K9FyTNk79ndGhqFt36x6nEbFgMLbmCDWumLuWN6bMd1Uq0wNkCqW4F1h28
3yqnY+rfQh4y3eXK1B9nttCUTs+/66U5ZWrT6B1IJumGTAIqcWfgeUX/Vn/HVC4=
=tfMc
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen updates from Konrad Rzeszutek Wilk:
"which has three neat features:
- PV multiconsole support, so that there can be hvc1, hvc2, etc; This
can be used in HVM and in PV mode.
- P-state and C-state power management driver that uploads said power
management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
There is one thing in the Kconfig that you won't like: "default y
if (X86_ACPI_CPUFREQ = y || X86_POWERNOW_K8 = y)" (note, that it
all depends on CONFIG_XEN which depends on CONFIG_PARAVIRT which by
default is off). I've a fix to convert that boolean expression
into "default m" which I am going to post after the cpufreq git
pull - as the two patches to make this work depend on a fix in Dave
Jones's tree.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx"
Fix up trivial conflicts in drivers/tty/hvc/hvc_xen.c due to changes to
a removed commit.
* tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen kconfig: relax INPUT_XEN_KBDDEV_FRONTEND deps
xen/acpi-processor: C and P-state driver that uploads said data to hypervisor.
xen: constify all instances of "struct attribute_group"
xen/xenbus: ignore console/0
hvc_xen: introduce HVC_XEN_FRONTEND
hvc_xen: implement multiconsole support
hvc_xen: support PV on HVM consoles
xenbus: don't free other end details too early
xen/enlighten: Expose MWAIT and MWAIT_LEAF if hypervisor OKs it.
xen/setup/pm/acpi: Remove the call to boot_option_idle_override.
xenbus: address compiler warnings
xen: use this_cpu_xxx replace percpu_xxx funcs
xen/pciback: Support pci_reset_function, aka FLR or D3 support.
pci: Introduce __pci_reset_function_locked to be used when holding device_lock.
xen: Utilize the restore_msi_irqs hook.
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink breakage
reverted), dynamic debugging updates, w1 drivers, hyperv driver updates,
and a variety of other bits and pieces, full information in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9neCsACgkQMUfUDdst+ylyQwCfY2eizvzw5HhjQs8gOiBRDADe
yrgAnj1Zan2QkoCnQIFJNAoxqNX9yAhd
=biH6
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches for 3.4-rc1 from Greg KH:
"Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink
breakage reverted), dynamic debugging updates, w1 drivers, hyperv
driver updates, and a variety of other bits and pieces, full
information in the shortlog."
* tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (78 commits)
Tools: hv: Support enumeration from all the pools
Tools: hv: Fully support the new KVP verbs in the user level daemon
Drivers: hv: Support the newly introduced KVP messages in the driver
Drivers: hv: Add new message types to enhance KVP
regulator: Support driver probe deferral
Revert "sysfs: Kill nlink counting."
uevent: send events in correct order according to seqnum (v3)
driver core: minor comment formatting cleanups
driver core: move the deferred probe pointer into the private area
drivercore: Add driver probe deferral mechanism
DS2781 Maxim Stand-Alone Fuel Gauge battery and w1 slave drivers
w1_bq27000: Only one thread can access the bq27000 at a time.
w1_bq27000 - remove w1_bq27000_write
w1_bq27000: remove unnecessary NULL test.
sysfs: Fix memory leak in sysfs_sd_setsecdata().
intel_idle: Revert change of auto_demotion_disable_flags for Nehalem
w1: Fix w1_bq27000
driver-core: documentation: fix up Greg's email address
powernow-k6: Really enable auto-loading
powernow-k7: Fix CPU family number
...
In 5bfa14ed9f, I forgot to initialize res2.flags before calling
pcibios_bus_to_resource(), which depends on the resource type to locate the
correct aperture. This bug won't hurt x86, which currently never has an
offset between bus and CPU addresses, but will affect other architectures.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Right now we won't touch ASPM state if ASPM is disabled, except in the case
where we find a device that appears to be too old to reliably support ASPM.
Right now we'll clear it in that case, which is almost certainly the wrong
thing to do. The easiest way around this is just to disable the blacklisting
when ASPM is disabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch recodes the MRRS cap for 5719 A0 devices as a PCI quirk.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are PCIe devices on the market that report ARI support but
then fail to initialize correctly when ARI is actually used. This
leads to situations in which kernels 2.6.34 and newer fail to handle
systems where the previous kernels worked without any apparent
problems. Unfortunately, it is currently unknown how many such
devices are there.
For this reason, introduce a new kernel command line option,
pci=noari, allowing users to disable PCIe ARI altogether if they
see problems with PCIe device initialization.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_stop_bus_device gets called before in the same loop.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Don't switch to pci_remove_bus_device yet, keep the __ prefix for now
(the behavior is still the same: remove without stopping first).
This allows other out of tree users or pending patches to get notified
from compiler warning.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The old pci_remove_behind_bridge actually do stop and remove.
Make the name reflect that to reduce confusion.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The old pci_remove_bus_device actually did stop and remove.
Make the name reflect that to reduce confusion.
This patch is done by sed scripts and changes back some incorrect
__pci_remove_bus_device changes.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Makes it a little easier to figure out which device may have caused a
slow quirk.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This isn't really a quirk; calling it directly from pci_add_device makes
more sense.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Recently added support to allow quirks to report duration also make the
boot log very crowded when initcall_debug is specified.
One thing we can to do mitigate this is to not call quirks unnecessarily
by adding a new quirk declaration macro that takes a class argument.
The new macro takes a class value and a class shift value (since it can
vary) so that quirks will be limited to certain device classes, greatly
reducing the number we call on every PCI device addition.
-v2: fix v1 that left over of sparated patch.
-v3: according to Jesse, change cls to class, cls_shift, to class_shift.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add a new config option, PCI_REALLOC_ENABLE_AUTO, which will
automatically try to re-allocate PCI resources if PCI_IOV support is
enabled and the SR-IOV resources are unassigned. Behavior can still be
controlled using the pci=realloc= parameter.
-v2: According to Jesse, adding one CONFIG option for distribution to
disable it or enable it.
-v3: update Kconfig text (jbarnes)
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
let user know they could try if pci=realloc could help.
-v2: update suggestion text.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Let the user could enable and disable with pci=realloc=on or pci=realloc=off
Also
1. move variable and functions near the place they are used.
2. change macro to function
3. change related functions and variable to static and _init
4. update parameter description accordingly.
This will let us add a config option to control default behavior, and
still allow the user to turn off automatic reallocation if it fails on
their platform until a permanent solution is found.
-v2: still honor pci=realloc, and treat it as pci=realloc=on
also use enum instead of ...
-v3: update kernel-paramenters.txt according to Jesse.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When enabling pci reallocation for a pci bridge, we clear the small size
in in bridge and re-assign with requested + optional size for first
several tries, but Ram mention could have problem with one case:
https://bugzilla.kernel.org/show_bug.cgi?id=15960
After checking the booting log in
https://lkml.org/lkml/2010/4/19/44
[regression, bisected] Xonar DX invalid PCI I/O range since 977d17bb17
We should not stop too early for io ports.
Apr 19 10:19:38 [kernel] pci 0000:04:00.0: BAR 7: can't assign io (size 0x4000)
Apr 19 10:19:38 [kernel] pci 0000:05:01.0: BAR 8: assigned [mem 0x80400000-0x805fffff]
Apr 19 10:19:38 [kernel] pci 0000:05:01.0: BAR 7: can't assign io (size 0x2000)
Apr 19 10:19:38 [kernel] pci 0000:05:02.0: BAR 7: can't assign io (size 0x1000)
Apr 19 10:19:38 [kernel] pci 0000:05:03.0: BAR 7: can't assign io (size 0x1000)
Apr 19 10:19:38 [kernel] pci 0000:08:00.0: BAR 7: can't assign io (size 0x1000)
Apr 19 10:19:38 [kernel] pci 0000:09:04.0: BAR 0: can't assign io (size 0x100)
and clear 00:1c.0 to retry again.
This patch removes IORESOUCE_IO checking, and tries one more time. It
gives us a chance to get an allocation for the 00:1c.0 io port range
because the range from 0x4000 to 0x8000 will be freed and we can use it.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Everybody uses the generic pcibios_resource_to_bus() supplied by the core
now, so remove the ARCH_HAS_GENERIC_PCI_OFFSETS used during conversion.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This replaces the generic versions of pcibios_resource_to_bus() and
pcibios_bus_to_resource() in asm-generic/pci.h with versions that use
pci_resource_to_bus() and pci_bus_to_resource().
The replacements are equivalent except that they can apply host
bridge window offsets when the arch has supplied them by using
pci_add_resource_offset().
Each arch can convert to using pci_add_resource_offset() individually by
removing its device resource fixups from pcibios_fixup_bus() and supplying
ARCH_HAS_GENERIC_PCI_OFFSETS. ARCH_HAS_GENERIC_PCI_OFFSETS can be removed
after all have converted.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some PCI host bridges translate CPU addresses to PCI bus addresses.
Previously, we initialized pci_dev resources with PCI bus addresses,
then converted them to CPU addresses later in arch-specific code
(pcibios_fixup_resources()), which leaves a window of time where the
pci_dev resources are incorrect.
This patch adds support in the core for this address translation.
When the arch creates the root bus, it can supply the host bridge
address translation information, and the core can use it to set the
pci_dev resources correctly from the beginning.
This gives us a way to fix the problem that quirks that run between device
discovery and pcibios_fixup_resources() fail because they use pci_dev
resources that haven't been converted. The reference below is to one
such problem that affected ARM and ia64.
Note that this patch has no effect until an arch starts using
pci_add_resource_offset() with a non-zero offset: before that, all
all host bridge windows have a zero offset and pci_bus_to_resource()
copies the pci_bus_region directly to the struct resource.
Reference: https://lkml.org/lkml/2009/10/12/405
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some PCI host bridges apply an address offset, so bus addresses on PCI are
different from CPU addresses. This patch adds a way for architectures to
tell the PCI core about this offset. For example:
LIST_HEAD(resources);
pci_add_resource_offset(&resources, host->io_space, host->io_offset);
pci_add_resource_offset(&resources, host->mem_space, host->mem_offset);
pci_scan_root_bus(parent, bus, ops, sysdata, &resources);
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This adds a list of all PCI host bridges we find and a way to look up
the host bridge from a pci_dev.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When pci_create_root_bus() adds the new struct pci_bus to the global
pci_root_buses list, the bus becomes visible to other parts of the
kernel, so it should be fully initialized.
This patch delays adding the bus to the pci_root_buses list until after
all the struct pci_bus initialization is finished.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If we move resource assignment functions into the core, we'll still
need a way for architectures to prevent reassignment, e.g., the
"pci_probe_only" functionality, and we'll need a generic, always
available way the core can test for that. The "pci_flags"
arrangement used by several architectures seems like a convenient
way to do this.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a parameter to avoid using MSI/MSI-X for PCIe native hotplug; it's
known to be buggy on some platforms.
In my environment, while shutting down, following stack trace is shown
sometimes.
irq 16: nobody cared (try booting with the "irqpoll" option)
Pid: 1081, comm: reboot Not tainted 3.2.0 #1
Call Trace:
<IRQ> [<ffffffff810cec1d>] __report_bad_irq+0x3d/0xe0
[<ffffffff810cee1c>] note_interrupt+0x15c/0x210
[<ffffffff810cc485>] handle_irq_event_percpu+0xb5/0x210
[<ffffffff810cc621>] handle_irq_event+0x41/0x70
[<ffffffff810cf675>] handle_fasteoi_irq+0x55/0xc0
[<ffffffff81015356>] handle_irq+0x46/0xb0
[<ffffffff814fbe9d>] do_IRQ+0x5d/0xe0
[<ffffffff814f146e>] common_interrupt+0x6e/0x6e
[<ffffffff8106b040>] ? __do_softirq+0x60/0x210
[<ffffffff8108aeb1>] ? hrtimer_interrupt+0x151/0x240
[<ffffffff814fb5ec>] call_softirq+0x1c/0x30
[<ffffffff810152d5>] do_softirq+0x65/0xa0
[<ffffffff8106ae9d>] irq_exit+0xbd/0xe0
[<ffffffff814fbf8e>] smp_apic_timer_interrupt+0x6e/0x99
[<ffffffff814f9e5e>] apic_timer_interrupt+0x6e/0x80
<EOI> [<ffffffff814f0fb1>] ? _raw_spin_unlock_irqrestore+0x11/0x20
[<ffffffff812629fc>] pci_bus_write_config_word+0x6c/0x80
[<ffffffff81266fc2>] pci_intx+0x52/0xa0
[<ffffffff8127de3d>] pci_intx_for_msi+0x1d/0x30
[<ffffffff8127e4fb>] pci_msi_shutdown+0x7b/0x110
[<ffffffff81269d34>] pci_device_shutdown+0x34/0x50
[<ffffffff81326c4f>] device_shutdown+0x2f/0x140
[<ffffffff8107b981>] kernel_restart_prepare+0x31/0x40
[<ffffffff8107b9e6>] kernel_restart+0x16/0x60
[<ffffffff8107bbfd>] sys_reboot+0x1ad/0x220
[<ffffffff814f4b90>] ? do_page_fault+0x1e0/0x460
[<ffffffff811942d0>] ? __sync_filesystem+0x90/0x90
[<ffffffff8105c9aa>] ? __cond_resched+0x2a/0x40
[<ffffffff814ef090>] ? _cond_resched+0x30/0x40
[<ffffffff81169e17>] ? iterate_supers+0xb7/0xd0
[<ffffffff814f9382>] system_call_fastpath+0x16/0x1b
handlers:
[<ffffffff8138a0f0>] usb_hcd_irq
[<ffffffff8138a0f0>] usb_hcd_irq
[<ffffffff8138a0f0>] usb_hcd_irq
Disabling IRQ #16
An un-wanted interrupt is generated when PCI driver switches from
MSI/MSI-X to INTx while shutting down the device. The interrupt does
not happen if MSI/MSI-X is not used on the device.
I confirmed that this problem does not happen if pcie_hp=nomsi was
specified and hotplug operation worked fine as usual.
v2: Automatically disable MSI/MSI-X against following device:
PCI bridge: Integrated Device Technology, Inc. Device 807f (rev 02)
v3: Based on the review comment, combile the if statements.
v4: Removed module parameter.
Move some code to build pciehp as a module.
Move device specific code to driver/pci/quirks.c.
v5: Drop a device specific code until getting a vendor statement.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Only one user in driver/pci/pci.c, so we don't need to put it in global
pci.h
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Found debug print of class is shifted.
| pci 0000:f8:15.2: [8086:2b56] type 0 class 0x000600
Code is trying to print class with 6 digits, but use shifted class with
4 digits valid value as variable.
Change to original dev->class directly.
Also remove not needed calculating of local variable class, because it
will be updated after pci_fixup_device(pci_fixup_early...)
Also unify type print out when class and header is not matched.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Otherwise when rescan is used for cardbus, assigned resources will get
cleared.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We should not set the requested size to -2; that will confuse the
resource list sorting with align when SIZEALIGN is used.
Change to STARTALIGN and pass align from start; we are safe to do that
just as we do that regular pci bridge. In the long run, we should just
treat cardbus like a regular pci bridge.
Also fix the case when realloc_head is not passed: we should keep the
requested size.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some BIOSes enable prefetch on both MEM0 and MEM1. But the cardbus code
assumes MEM1 is non-pref...
Discussion could be found at:
https://lkml.org/lkml/2012/1/12/1https://bugzilla.kernel.org/show_bug.cgi?id=41622#c23
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One regression fix for SR-IOV on PPC and a couple of misc fixes from
Yinghai.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Fix pci cardbus removal
PCI: set pci sriov page size before reading SRIOV BAR
PCI: workaround hard-wired bus number V2
If a PCI device is enabled to generate wakeup signals (PME) when put
into a low-power state by runtime PM, it will be still enabled to
generate those signals after the system shutdown, unless its driver's
.shutdown() callback takes care of the wakeup signals generation
setting. Moreover, there are devices that are not enabled to wake
up the system and that are configured by runtime PM to generate
wakeup signals so that (runtime) remote wakeup works with them.
Those devices should be reconfigured during system shutdown so that
they don't generate wakeup signals, but at least some drivers don't
do that. However, that very well may be done by the PCI core so
that drivers don't have to worry about it. For this reason, modify
pci_device_shutdown() to disable the generation of wakeup events for
devices not supposed to wake up the system.
References: https://bugzilla.kernel.org/show_bug.cgi?id=37952
Reported-and-tested-by: Kamil Iskra <kamil.54002@iskra.name>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
sysfs is a bit stricter now and emits warnings in more cases.
For SRIOV hotplug, we are calling pci_stop_dev() for each VF first
(after we update pci_stop_bus_devices) which remove each VF subdir. So
double check the VF dir in /sys before trying to remove the physfn link.
Signed-of-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Distributions may wish to provide different defaults for PCIE ASPM
depending on their target audience. Provide a configuration option for
choosing the default policy.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
by the xen-pci[front|back] to conform to the one used in majority of
PCI drivers; Two fixes to make the code more resilient to invalid
configurations.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPOeReAAoJEFjIrFwIi8fJn9QIANP48kzrGg0uO4bjSf2h/z7G
pp3ISdtVLk7pwMov2POBqskoXSq8E0yQAfNN8se183wqNXo3Dm4rU1DIG7HQFBk9
sdcyfHI8x7pat9JClRhGxpQ23Ig9f1iWkShweCcZCO782vfxZyNd65i6t87X7uLq
7SPtG1XH2RixTX7tHtKKBqdzZ0OMXOEkJ33dgCmyrn+wzohbKrFj5mg+NdOgmzEo
VgsHPVtuq7orDROe+F9d91eAg0TILQ13th8xfWZ59lQATXu/zAlaueYt87tpy1pb
oVQvumsn8Xev+7hct9My9Tw45D4m8YOSFLG2HcekkW2WtNmGhTTbIyMh9PsLugk=
=NDYK
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Two fixes for VCPU offlining; One to fix the string format exposed
by the xen-pci[front|back] to conform to the one used in majority of
PCI drivers; Two fixes to make the code more resilient to invalid
configurations.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus_dev: add missing error check to watch handling
xen/pci[front|back]: Use %d instead of %1x for displaying PCI devfn.
xen pvhvm: do not remap pirqs onto evtchns if !xen_have_vector_callback
xen/smp: Fix CPU online/offline bug triggering a BUG: scheduling while atomic.
xen/bootup: During bootup suppress XENBUS: Unable to read cpu state
Some BIOS implementations leave the Intel GPU interrupts enabled,
even though no one is handling them (f.e. i915 driver is never loaded).
Additionally the interrupt destination is not set up properly
and the interrupt ends up -somewhere-.
These spurious interrupts are "sticky" and the kernel disables
the (shared) interrupt line after 100.000+ generated interrupts.
Fix it by disabling the still enabled interrupts.
This resolves crashes often seen on monitor unplug.
Tested on the following boards:
- Intel DH61CR: Affected
- Intel DH67BL: Affected
- Intel S1200KP server board: Affected
- Asus P8H61-M LE: Affected, but system does not crash.
Probably the IRQ ends up somewhere unnoticed.
According to reports on the net, the Intel DH61WW board is also affected.
Many thanks to Jesse Barnes from Intel for helping
with the register configuration and to Intel in general
for providing public hardware documentation.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Tested-by: Charlie Suffin <charlie.suffin@stratus.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While diagnosing some boot time issues on a platform, all that I
could see in the bootgraph/dmesg was that the system was spending
a lot of time in applying one or more PCI quirks... which
was virtually undebuggable.
This patch adds printk's in "initcall_debug" style to the dmesg,
which are added when the user asks for the initcall_debug
(the nr one tool to use when debugging boot hangs or boot time issues)
kernel command line option.
v2: add #includes so quirks can build on non-x86
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix debug variable from module parameter to be really bool to
fix 'warning: return from incompatible pointer type'.
Acked-by: Scott Murray <scott@spiteful.org>
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On some OEM systems, pci_restore_state() is called while FLR has not yet
completed. As a result, PCI BAR register restore is not successful. This fix
reads back the restored value and compares it with saved value and re-tries 10
times before giving up.
Signed-off-by: Jean Guyader <jean.guyader@eu.citrix.com>
Signed-off-by: Eric Chanudet <eric.chanudet@citrix.com>
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On a system with a repeater on the system board to support gen2 hotplug,
we found that when an ExpressModule is removed from some slots,
/var/log/messages will be full of "card present/not present" warnings.
It turns out the root complex is continually trying to train the link to
the repeater because the repeater has not been reset.
This patch will disable the link at removal time to allow the repeater
to be reset properly. This also prevents a potential AER message at
removal time.
Also, when testing hotplug on a system under development, we found if we
boot the system without an EM installed, and later hot-add an EM, it
does not work with Linux, but another OS is ok. The root cause is that
BIOS left link disabled when slot was empty at boot time, and other OS
is modifying the link disable bit in link ctrl during power on/off.
So we should do the same thing to disable/enable link during power off/on.
-v2: check link DLLA bit instead of 100ms waiting.
Separate link disable/enable functions to another patch.
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A few changes:
- remove the 'inline' and let the complier decide
- return a bool to indicate whether the link was active
- add a debug message to indicate link state when it beocmes active
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During reviewing
| PCI: pciehp: wait 1000 ms before Link Training check
Linus said:
>...
> That's a *long* time, and it's irritating to the user. It makes the
> user think "the machine is slow".
>...
> And quite frankly, an unconditional one-second delay here seems bad.
>Two seconds was unacceptable, one second is just bad.
Try to access the pci conf of a pci device that is supposed to show up
in 1s. If we can read back a valid vendor/device id, we can return
early.
Related discussion could be found:
https://lkml.org/lkml/2011/12/6/339
-v2: seperate code to pci_bus_read_dev_vendor_id() from pci_scan_device()
and reuse it from pciehp code. Suggested by Matthew Wilcox.
-v3: According to Kenj, don't use array in stack, and don't wait too long
for crs, also return fail status if not found.
Also separate pci_bus_dev_read_vendor_id() change to another patch.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We can reuse it for pciehp probing.
-v2: according to Kenji, fix crs timeout checking, and export the function
for later use when pciehp is compiled as a module.
Suggested-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When hot removing a pci express module that has a pcie switch and supports
SRIOV, we got:
[ 5918.610127] pciehp 0000:80:02.2:pcie04: pcie_isr: intr_loc 1
[ 5918.615779] pciehp 0000:80:02.2:pcie04: Attention button interrupt received
[ 5918.622730] pciehp 0000:80:02.2:pcie04: Button pressed on Slot(3)
[ 5918.629002] pciehp 0000:80:02.2:pcie04: pciehp_get_power_status: SLOTCTRL a8 value read 1f9
[ 5918.637416] pciehp 0000:80:02.2:pcie04: PCI slot #3 - powering off due to button press.
[ 5918.647125] pciehp 0000:80:02.2:pcie04: pcie_isr: intr_loc 10
[ 5918.653039] pciehp 0000:80:02.2:pcie04: pciehp_green_led_blink: SLOTCTRL a8 write cmd 200
[ 5918.661229] pciehp 0000:80:02.2:pcie04: pciehp_set_attention_status: SLOTCTRL a8 write cmd c0
[ 5924.667627] pciehp 0000:80:02.2:pcie04: Disabling domain🚌device=0000:b0:00
[ 5924.674909] pciehp 0000:80:02.2:pcie04: pciehp_get_power_status: SLOTCTRL a8 value read 2f9
[ 5924.683262] pciehp 0000:80:02.2:pcie04: pciehp_unconfigure_device: domain🚌dev = 0000:b0:00
[ 5924.693976] libfcoe_device_notification: NETDEV_UNREGISTER eth6
[ 5924.764979] libfcoe_device_notification: NETDEV_UNREGISTER eth14
[ 5924.873539] libfcoe_device_notification: NETDEV_UNREGISTER eth15
[ 5924.995209] libfcoe_device_notification: NETDEV_UNREGISTER eth16
[ 5926.114407] sxge 0000:b2:00.0: PCI INT A disabled
[ 5926.119342] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 5926.127189] IP: [<ffffffff81353a3b>] pci_stop_bus_device+0x33/0x83
[ 5926.133377] PGD 0
[ 5926.135402] Oops: 0000 [#1] SMP
[ 5926.138659] CPU 2
[ 5926.140499] Modules linked in:
...
[ 5926.143754]
[ 5926.275823] Call Trace:
[ 5926.278267] [<ffffffff81353a38>] pci_stop_bus_device+0x30/0x83
[ 5926.284180] [<ffffffff81353af4>] pci_remove_bus_device+0x1a/0xba
[ 5926.290264] [<ffffffff81366311>] pciehp_unconfigure_device+0x110/0x17b
[ 5926.296866] [<ffffffff81365dd9>] ? pciehp_disable_slot+0x188/0x188
[ 5926.303123] [<ffffffff81365d6f>] pciehp_disable_slot+0x11e/0x188
[ 5926.309206] [<ffffffff81365e68>] pciehp_power_thread+0x8f/0xe0
...
+-[0000:80]-+-00.0-[81-8f]--
| +-01.0-[90-9f]--
| +-02.0-[a0-af]--
| +-02.2-[b0-bf]----00.0-[b1-b3]--+-02.0-[b2]--+-00.0 Device
| | | +-00.1 Device
| | | +-00.2 Device
| | | \-00.3 Device
| | \-03.0-[b3]--+-00.0 Device
| | +-00.1 Device
| | +-00.2 Device
| | \-00.3 Device
root complex: 80:02.2
pci express modules: have pcie switch and are listed as b0:00.0, b1:02.0 and b1:03.0.
end devices are b2:00.0 and b3.00.0.
VFs are: b2:00.1,... b2:00.3, and b3:00.1,...,b3:00.3
Root cause: when doing pci_stop_bus_device() with phys fn, it will stop
virt fn and remove the fn, so
list_for_each_safe(l, n, &bus->devices)
will have problem to refer freed n that is pointed to vf entry.
Solution is just replacing list_for_each_safe() with
list_for_each_prev_safe(). This will make sure we can get valid n pointer
to PF instead of the freed VF pointer (because newly added devices are
inserted to the bus->devices list tail).
During reviewing the patch, Bjorn said:
| The PCI hot-remove path calls pci_stop_bus_devices() via
| pci_remove_bus_device().
|
| pci_stop_bus_devices() traverses the bus->devices list (point A below),
| stopping each device in turn, which calls the driver remove() method. When
| the device is an SR-IOV PF, the driver calls pci_disable_sriov(), which
| also uses pci_remove_bus_device() to remove the VF devices from the
| bus->devices list (point B).
|
| pci_remove_bus_device
| pci_stop_bus_device
| pci_stop_bus_devices(subordinate)
| list_for_each(bus->devices) <-- A
| pci_stop_bus_device(PF)
| ...
| driver->remove
| pci_disable_sriov
| ...
| pci_remove_bus_device(VF)
| <remove from bus_list> <-- B
|
| At B, we're changing the same list we're iterating through at A, so when
| the driver remove() method returns, the pci_stop_bus_devices() iterator has
| a pointer to a list entry that has already been freed.
Discussion thread can be found : https://lkml.org/lkml/2011/10/15/141https://lkml.org/lkml/2012/1/23/360
-v5: According to Linus to make remove more robust, Change to
list_for_each_prev_safe instead. That is more reasonable, because
those devices are added to tail of the list before.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After merging struct pci_dev_resource_x and pci_dev_resource,
We can use a function instead of macro now.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Linus says don't use dev_res_x because it doesn't communicate anything
about usage. Rename them to add_res or fail_res etc according to
context.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_dev_resource_x is a superset of pci_dev_resource and they're just
temp structs used during resource reallocation.
pci_dev_resource usage is quite limted.
So just use pci_dev_resource_x, and rename it as new pci_dev_resource.
-v2: According to Linus, Separate free_list change to another patch
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
So we can use helper functions for generic list. This makes the
resource re-allocation code much more readable.
-v2: Use list_add_tail instead of adding list_insert_before, Pointed out
by Linus.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No user outside of setup-bus.c now. Later patches will convert
resource_list to a regular list.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This allows us to move the definition of struct resource_list to
setup_bus.c and later convert resource_list to a regular list.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On a system with devices that support SRIOV connected to a pcie switch
to pcie root port:
+-[0000:80]-+-00.0-[81-8f]--
| +-01.0-[90-9f]--
| +-02.0-[a0-af]----00.0-[a1-a3]--+-02.0-[a2]--+-00.0 Oracle Corporation Device 207a
| | \-03.0-[a3]--+-00.0 Oracle Corporation Device 207a
| +-02.2-[b0-bf]----00.0-[b1-b3]--+-02.0-[b2]--+-00.0 Oracle Corporation Device 207a
| | \-03.0-[b3]--+-00.0 Oracle Corporation Device 207a
When the BIOS does not assign resources for SRIOV BARs, kernel pci
reallocation only goes up one bridge and then gives up, failing to to
get resources for all sSRIOV BARs, even though the range is large enough
in the peer root bus.
Specifically, only the bridge at the a1:02.0 level has its resources
cleared and reallocated. The kernel does not go up to clear the bridge
at the 80:02.0 level.
To make it go to upper levels, during retry, we need to treat "good to have"
resources as "must have".
Only on the last try will we treat good to have resources as optional.
At that time, parent bridge resources will already have been released so
we'll have a chance to get everything assigned with must_have plus
good_to_have for all child devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This allows us to allocate resources to hotplug bridges during
remove/rescan.
We need to move the function to setup-bus.c so it can use
__pci_bus_size_bridges and __pci_bus_assign_resources directly to take
the add_list resource tracking list.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current rescan will not touch bridge MMIO and IO.
Try to reuse pci_assign_unassigned_bridge_resources(bridge) to update bridge
resources, if child devices need more resources.
Only do that for bridges whose children are all removed already; i.e. don't
release resources that could already be in use by drivers on child devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We need add size for hot plug path when pluging in hotplug chassis
without cards.
-v2: change descriptions. make it applicable after "pci: Check bridge
resources after resource allocation."
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Need to call it from __assign_resources_sorted() later and we'd like to
avoid a forward declaraion.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Will be used for resource_list_x duplication when trying
requested+optional at first.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During debug of one SRIOV enabled hotplug device, we found found that
add_size is not passed properly.
The device has devices under two level bridges:
+-[0000:80]-+-00.0-[81-8f]--
| +-01.0-[90-9f]--
| +-02.0-[a0-af]----00.0-[a1-a3]--+-02.0-[a2]--+-00.0 Oracle Corporation Device
| | \-03.0-[a3]--+-00.0 Oracle Corporation Device
Which means later the parent bridge will not try to add a big enough range:
[ 557.455077] pci 0000:a0:00.0: BAR 14: assigned [mem 0xf9000000-0xf93fffff]
[ 557.461974] pci 0000:a0:00.0: BAR 15: assigned [mem 0xf6000000-0xf61fffff pref]
[ 557.469340] pci 0000:a1:02.0: BAR 14: assigned [mem 0xf9000000-0xf91fffff]
[ 557.476231] pci 0000:a1:02.0: BAR 15: assigned [mem 0xf6000000-0xf60fffff pref]
[ 557.483582] pci 0000:a1:03.0: BAR 14: assigned [mem 0xf9200000-0xf93fffff]
[ 557.490468] pci 0000:a1:03.0: BAR 15: assigned [mem 0xf6100000-0xf61fffff pref]
[ 557.497833] pci 0000:a1:03.0: BAR 14: can't assign mem (size 0x200000)
[ 557.504378] pci 0000:a1:03.0: failed to add optional resources res=[mem 0xf9200000-0xf93fffff]
[ 557.513026] pci 0000:a1:02.0: BAR 14: can't assign mem (size 0x200000)
[ 557.519578] pci 0000:a1:02.0: failed to add optional resources res=[mem 0xf9000000-0xf91fffff]
It turns out we did not calculate size1 properly.
static resource_size_t calculate_memsize(resource_size_t size,
resource_size_t min_size,
resource_size_t size1,
resource_size_t old_size,
resource_size_t align)
{
if (size < min_size)
size = min_size;
if (old_size == 1 )
old_size = 0;
if (size < old_size)
size = old_size;
size = ALIGN(size + size1, align);
return size;
}
We should not pass add_size with min_size in calculate_memsize since
that will make add_size not contribute final add_size.
So just pass add_size with size1 to calculate_memsize().
With this change, we should have chance to remove extra addon in
pci_reassign_resource.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The use case of this is when a driver wants to call FLR when a device
is attached to it using the SysFS "bind" or "unbind" functionality.
The call chain when a user does "bind" looks as so:
echo "0000:01.07.0" > /sys/bus/pci/drivers/XXXX/bind
and ends up calling:
driver_bind:
device_lock(dev); <=== TAKES LOCK
XXXX_probe:
.. pci_enable_device()
...__pci_reset_function(), which calls
pci_dev_reset(dev, 0):
if (!0) {
device_lock(dev) <==== DEADLOCK
The __pci_reset_function_locked function allows the the drivers
'probe' function to call the "pci_reset_function" while still holding
the driver mutex lock.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Boot up a KVM guest, and hotplug multifunction
devices(func1,func2,func0,func3) to guest.
for i in 1 2 0 3;do
qemu-img create /tmp/resize$i.qcow2 1G -f qcow2
(qemu) drive_add 0x11.$i id=drv11$i,if=none,file=/tmp/resize$i.qcow2
(qemu) device_add virtio-blk-pci,id=dev11$i,drive=drv11$i,addr=0x11.$i,multifunction=on
done
In linux kernel, when func0 of the slot is hot-added, the whole
slot will be marked as 'enabled', then driver will ignore other new
hotadded funcs.
But in Win7 & WinXP, we can continaully add other funcs after adding
func0, all funcs will be added in guest.
drivers/pci/hotplug/acpiphp_glue.c:
static int acpiphp_check_bridge(struct acpiphp_bridge *bridge)
{
....
for (slot = bridge->slots; slot; slot = slot->next) {
if (slot->flags & SLOT_ENABLED) {
acpiphp_disable_slot()
else
acpiphp_enable_slot()
.... |
} v
enable_device()
|
v
//only don't enable slot if func0 is not added
list_for_each_entry(func, &slot->funcs, sibling) {
...
}
slot->flags |= SLOT_ENABLED; //mark slot to 'enabled'
This patch just make pci driver can continaully add funcs after adding
func 0. Only mark slot to 'enabled' when all funcs are added.
For pci multifunction hotplug, we can add functions one by one(func 0 is
necessary), and all functions will be removed in one time.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch converts the underlying maintenance aspects of FW-assigned
BIOS BAR values from a statically allocated array within struct pci_dev
to a list of temporary, stand alone, entries.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_revert_fw_address() is used to reinstate a PCI device's original
FW-assigned BIOS BAR value(s) if normal resource assignment fails.
When attempting to reinstate an address, the point within the resource
tree from which to attempt the new resource request should be the parent
resource corresponding to the device, not the base of the resource tree
(ioport_resource or iomem_resource). For PCI devices this would
typically be the resource corresponding to the upstream PCI host bridge
or P2P bridge aperture.
This patch sets the point within the resource tree to attempt a new
resource assignment request to the PCI device's parent resource and only
if that fails does it fall back to the base ioport_resource or
iomem_resource.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During test busn_res allocation with cardbus, found pci card removal is not
working anymore, and it turns out it is broken by:
|commit 79cc9601c3
|Date: Tue Nov 22 21:06:53 2011 -0800
|
| PCI: Only call pci_stop_bus_device() one time for child devices at remove
The above changed the behavior of pci_remove_behind_bridge that
yenta_cardbus depended on. So restore the old behavoir of
pci_remove_behind_bridge (which requires stopping and removing of all
devices) by:
1. rename pci_remove_behind_bridge to __pci_remove_behind_bridge, and let
__pci_remove_bus_device() call it instead.
2. add pci_stop_behind_bridge that will stop devices behind a bridge
3. add back pci_remove_behind_bridge that will stop and remove devices
under bridge.
-v2: update commit description a little bit.
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For an SRIOV device, PCI_SRIOV_SYS_PGSIZE should be set before
the PCI_SRIOV_BAR are queried. The sys pagesize defaults to 4k,
so this change is required on powerpc box with 64k base page size.
This is a regression caused due to moving SRIOV init to sriov_enable().
| commit afd24ece5c
| Author: Ram Pai <linuxram@us.ibm.com>
| PCI: delay configuration of SRIOV capability
| The SRIOV capability, namely page size and total_vfs of a device are
| configured during enumeration phase of the device. This can potentially
| interfere with the PCI operations of the platform, if the IOV capability
| of the device is not enabled.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fixes PCI device detection on IBM xSeries IBM 3850 M2 / x3950 M2
when using ACPI resources (_CRS).
This is default, a manual workaround (without this patch)
would be pci=nocrs boot param.
V2: Add dev_warn if the workaround is hit. This should reveal
how common such setups are (via google) and point to possible
problems if things are still not working as expected.
-> Suggested by Jan Beulich.
Cc: stable@vger.kernel.org
Tested-by: garyhade@us.ibm.com
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
.. as the rest of the kernel is using that format.
Suggested-by: Марк Коренберг <socketpair@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This was done to resolve a merge and build problem with the
drivers/acpi/processor_driver.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1516) fixes a bug introduced during the removal of
put_driver() and get_driver() from drivers/pci/xen-pcifront.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1514) cleans up some places where new_id and remove_id
sysfs attributes are created and deleted. Handling both attributes in
a single routine rather than a pair of routines makes the code
smaller. It also prevents certain kinds of errors, like one we
currently have in the USB subsystem: The removeid attribute is often
created even when newid isn't (because the driver's no_dynamid_id flag
is set).
In the case of the PCMCIA subsystem, the newid attribute is created
but never explicitly deleted. The patch adds a deletion routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As part of the removal of get_driver()/put_driver(), this patch
(as1512) gets rid of various useless and unnecessary calls in several
drivers. In some cases it may be desirable to pin the driver by
calling try_module_get(), but that can be done later.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: "David S. Miller" <davem@davemloft.net>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Michael Buesch <m@bues.ch>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As part of the removal of get_driver()/put_driver(), this patch
(as1511) changes all the places that add dynamic IDs for drivers.
Since these additions are done by writing to the drivers' sysfs
attribute files, and the attributes are removed when the drivers are
unregistered, there is no reason to take an extra reference to the
drivers.
The one exception is the pci-stub driver, which calls pci_add_dynid()
as part of its registration. But again, there's no reason to take an
extra reference here, because the driver can't be unloaded while it is
being registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix new kernel-doc warnings:
Warning(drivers/pci/pci.c:2811): No description found for parameter 'dev'
Warning(drivers/pci/pci.c:2811): Excess function parameter 'pdev' description in 'pci_intx_mask_supported'
Warning(drivers/pci/pci.c:2894): No description found for parameter 'dev'
Warning(drivers/pci/pci.c:2894): Excess function parameter 'pdev' description in 'pci_check_and_mask_intx'
Warning(drivers/pci/pci.c:2908): No description found for parameter 'dev'
Warning(drivers/pci/pci.c:2908): Excess function parameter 'pdev' description in 'pci_check_and_unmask_intx'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://selinuxproject.org/~jmorris/linux-security:
capabilities: remove __cap_full_set definition
security: remove the security_netlink_recv hook as it is equivalent to capable()
ptrace: do not audit capability check when outputing /proc/pid/stat
capabilities: remove task_ns_* functions
capabitlies: ns_capable can use the cap helpers rather than lsm call
capabilities: style only - move capable below ns_capable
capabilites: introduce new has_ns_capabilities_noaudit
capabilities: call has_ns_capability from has_capability
capabilities: remove all _real_ interfaces
capabilities: introduce security_capable_noaudit
capabilities: reverse arguments to security_capable
capabilities: remove the task from capable LSM hook entirely
selinux: sparse fix: fix several warnings in the security server cod
selinux: sparse fix: fix warnings in netlink code
selinux: sparse fix: eliminate warnings for selinuxfs
selinux: sparse fix: declare selinux_disable() in security.h
selinux: sparse fix: move selinux_complete_init
selinux: sparse fix: make selinux_secmark_refcount static
SELinux: Fix RCU deref check warning in sel_netport_insert()
Manually fix up a semantic mis-merge wrt security_netlink_recv():
- the interface was removed in commit fd77846152 ("security: remove
the security_netlink_recv hook as it is equivalent to capable()")
- a new user of it appeared in commit a38f7907b9 ("crypto: Add
userspace configuration API")
causing no automatic merge conflict, but Eric Paris pointed out the
issue.
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The use case of this is when a driver wants to call FLR when a device
is attached to it using the SysFS "bind" or "unbind" functionality.
The call chain when a user does "bind" looks as so:
echo "0000:01.07.0" > /sys/bus/pci/drivers/XXXX/bind
and ends up calling:
driver_bind:
device_lock(dev); <=== TAKES LOCK
XXXX_probe:
.. pci_enable_device()
...__pci_reset_function(), which calls
pci_dev_reset(dev, 0):
if (!0) {
device_lock(dev) <==== DEADLOCK
The __pci_reset_function_locked function allows the the drivers
'probe' function to call the "pci_reset_function" while still holding
the driver mutex lock.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
* 'stable/for-linus-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (37 commits)
xen/pciback: Expand the warning message to include domain id.
xen/pciback: Fix "device has been assigned to X domain!" warning
xen/pciback: Move the PCI_DEV_FLAGS_ASSIGNED ops to the "[un|]bind"
xen/xenbus: don't reimplement kvasprintf via a fixed size buffer
xenbus: maximum buffer size is XENSTORE_PAYLOAD_MAX
xen/xenbus: Reject replies with payload > XENSTORE_PAYLOAD_MAX.
Xen: consolidate and simplify struct xenbus_driver instantiation
xen-gntalloc: introduce missing kfree
xen/xenbus: Fix compile error - missing header for xen_initial_domain()
xen/netback: Enable netback on HVM guests
xen/grant-table: Support mappings required by blkback
xenbus: Use grant-table wrapper functions
xenbus: Support HVM backends
xen/xenbus-frontend: Fix compile error with randconfig
xen/xenbus-frontend: Make error message more clear
xen/privcmd: Remove unused support for arch specific privcmp mmap
xen: Add xenbus_backend device
xen: Add xenbus device driver
xen: Add privcmd device driver
xen/gntalloc: fix reference counts on multi-page mappings
...
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
The MSI restore function will become a function pointer in an
x86_msi_ops struct. It defaults to the implementation in the
io_apic.c and msi.c. We piggyback on the indirection mechanism
introduced by "x86: Introduce x86_msi_ops".
Cc: x86@kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Skip cpus with apic-ids >= 255 in !x2apic_mode
x86, x2apic: Allow "nox2apic" to disable x2apic mode setup by BIOS
x86, x2apic: Fallback to xapic when BIOS doesn't setup interrupt-remapping
x86, acpi: Skip acpi x2apic entries if the x2apic feature is not present
x86, apic: Add probe() for apic_flat
x86: Simplify code by removing a !SMP #ifdefs from 'struct cpuinfo_x86'
x86: Convert per-cpu counter icr_read_retry_count into a member of irq_stat
x86: Add per-cpu stat counter for APIC ICR read tries
pci, x86/io-apic: Allow PCI_IOAPIC to be user configurable on x86
x86: Fix the !CONFIG_NUMA build of the new CPU ID fixup code support
x86: Add NumaChip support
x86: Add x86_init platform override to fix up NUMA core numbering
x86: Make flat_init_apic_ldr() available
During S3 or S4 resume or PCI reset, ATS regs aren't restored correctly.
This patch enables ATS at the device state restore if PCI device has ATS
capability.
Signed-off-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This warning was recently reported to me:
------------[ cut here ]------------
WARNING: at lib/kobject.c:595 kobject_put+0x50/0x60()
Hardware name: VMware Virtual Platform
kobject: '(null)' (ffff880027b0df40): is not initialized, yet kobject_put() is
being called.
Modules linked in: vmxnet3(+) vmw_balloon i2c_piix4 i2c_core shpchp raid10
vmw_pvscsi
Pid: 630, comm: modprobe Tainted: G W 3.1.6-1.fc16.x86_64 #1
Call Trace:
[<ffffffff8106b73f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8106b836>] warn_slowpath_fmt+0x46/0x50
[<ffffffff810da293>] ? free_desc+0x63/0x70
[<ffffffff812a9aa0>] kobject_put+0x50/0x60
[<ffffffff812e4c25>] free_msi_irqs+0xd5/0x120
[<ffffffff812e524c>] pci_enable_msi_block+0x24c/0x2c0
[<ffffffffa017c273>] vmxnet3_alloc_intr_resources+0x173/0x240 [vmxnet3]
[<ffffffffa0182e94>] vmxnet3_probe_device+0x615/0x834 [vmxnet3]
[<ffffffff812d141c>] local_pci_probe+0x5c/0xd0
[<ffffffff812d2cb9>] pci_device_probe+0x109/0x130
[<ffffffff8138ba2c>] driver_probe_device+0x9c/0x2b0
[<ffffffff8138bceb>] __driver_attach+0xab/0xb0
[<ffffffff8138bc40>] ? driver_probe_device+0x2b0/0x2b0
[<ffffffff8138bc40>] ? driver_probe_device+0x2b0/0x2b0
[<ffffffff8138a8ac>] bus_for_each_dev+0x5c/0x90
[<ffffffff8138b63e>] driver_attach+0x1e/0x20
[<ffffffff8138b240>] bus_add_driver+0x1b0/0x2a0
[<ffffffffa0188000>] ? 0xffffffffa0187fff
[<ffffffff8138c246>] driver_register+0x76/0x140
[<ffffffff815ca414>] ? printk+0x51/0x53
[<ffffffffa0188000>] ? 0xffffffffa0187fff
[<ffffffff812d2996>] __pci_register_driver+0x56/0xd0
[<ffffffffa018803a>] vmxnet3_init_module+0x3a/0x3c [vmxnet3]
[<ffffffff81002042>] do_one_initcall+0x42/0x180
[<ffffffff810aad71>] sys_init_module+0x91/0x200
[<ffffffff815dccc2>] system_call_fastpath+0x16/0x1b
---[ end trace 44593438a59a9558 ]---
Using INTx interrupt, #Rx queues: 1.
It occurs when populate_msi_sysfs fails, which in turn causes free_msi_irqs to
be called. Because populate_msi_sysfs fails, we never registered any of the
msi irq sysfs objects, but free_msi_irqs still calls kobject_del and kobject_put
on each of them, which gets flagged in the above stack trace.
The fix is pretty straightforward. We can key of the parent pointer in the
kobject. It is only set if the kobject_init_and_add succededs in
populate_msi_sysfs. If anything fails there, each kobject has its parent reset
to NULL
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: linux-pci@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When the runtime PM is activated on PCI, if a device switches state
frequently (e.g. an EHCI controller with autosuspending USB devices
connected) the PCI configuration traces might be very verbose in the
kernel log. Let's guard those traces with DEBUG condition.
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All users of pci_create_bus() have been converted to pci_create_root_bus(),
so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Users of pci_scan_bus_parented() should be converted to use either
pci_scan_root_bus() (preferred, but also calls pci_bus_add_devices)
or
pci_create_root_bus()
pci_scan_child_bus()
Since pci_scan_bus_parented(), I'm marking it deprecated now and will
actually remove it later.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This converts pci_scan_bus_parented() to use pci_create_root_bus()
instead of pci_create_bus(). The new bus still has the default (incorrect)
resources, so this patch doesn't help fix that problem, but it does remove
one more use of pci_create_bus().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I plan to deprecate pci_scan_bus_parented(), so use pci_create_root_bus()
directly instead. pci_scan_bus() itself will be removed as soon as all
callers are gone, so this is just an interim step.
v2: export pci_scan_bus
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
"Early" and "header" quirks often use incorrect bus resources because they
see the default resources assigned by pci_create_bus(), before the
architecture fixes them up (typically in pcibios_fixup_bus()). Regions
reserved by these quirks end up with the wrong parents.
Here's the standard path for scanning a PCI root bus:
pci_scan_bus or pci_scan_bus_parented
pci_create_bus <-- A create with default resources
pci_scan_child_bus
pci_scan_slot
pci_scan_single_device
pci_scan_device
pci_setup_device
pci_fixup_device(early) <-- B
pci_device_add
pci_fixup_device(header) <-- C
pcibios_fixup_bus <-- D fill in correct resources
Early and header quirks at B and C use the default (incorrect) root bus
resources rather than those filled in at D.
This patch adds a new pci_scan_root_bus() function that sets the bus
resources correctly from a supplied list of resources.
I intend to remove pci_scan_bus() and pci_scan_bus_parented() after
fixing all callers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_create_bus() assigns ioport_resource and iomem_resource as the default
bus resources, i.e., the entire address space. Architectures fix these
later, typically in pcibios_fixup_bus() or after pci_scan_bus_parented()
returns, but code that runs in the interim sees incorrect resource
information.
This patch adds a new pci_create_root_bus() that sets the bus resources
correctly from a supplied list of resources.
I intend to remove pci_create_bus() after changing all callers.
Based on original patch by Deng-Cheng Zhu.
Reference: http://www.spinics.net/lists/mips/msg41654.html
Reference: https://lkml.org/lkml/2011/8/26/88
Signed-off-by: Deng-Cheng Zhu <dczhu@mips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Show the bus number and resources for every root bus we create. This
will become more interesting when we supply the correct resources
instead of using the defaults (ioport_resource and iomem_resource).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We'd like to supply a list of resources when we create a new PCI bus,
e.g., the root bus under a PCI host bridge. These are helpers for
constructing that list.
These are exported because the plan is to replace this exported interface:
pci_scan_bus_parented()
with this one:
pci_add_resource(resources, ...)
pci_scan_root_bus(..., resources)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The SRIOV capability, namely page size and total_vfs of a device are
configured during enumeration phase of the device. This can potentially
interfere with the PCI operations of the platform, if the IOV capability
of the device is not enabled.
The following patch postpones the configuration of the IOV capability of
the device to a later point, when the IOV capability is explicitly
enabled by the device driver.
The patch is tested on x86 and power platform.
Tested-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During debugging pcie hotplug with SRIOV with pcie switch, I found
pci_stop_bus_device() is called several times for some child devices.
So change original pci_remove_bus_device() to __pci_remove_bus_device(),
and make it only do remove work, and add a new pci_remove_bus_device
that calls pci_stop_bus_device() one time, and then call
__pci_remove_bus_device().
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The latency timer is read-only and hardwired to zero for all PCIe
devices, both Type 0 and Type 1, so don't bother trying to update it
and cluttering the dmesg log with meaningless "setting latency timer
to 64" messages.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'latency timer' of PCI devices, both Type 0 and Type 1,
is setup in architecture-specific code [see: 'pcibios_set_master()'].
There are two approaches being taken by all the architectures - check
if the 'latency timer' is currently set between 16 and 255 and if not
bring it within bounds, or, do nothing (and then there is the
gratuitously different PA-RISC implementation).
There is nothing architecture-specific about PCI's 'latency timer' so
this patch pulls its setup functionality up into the PCI core by
creating a generic 'pcibios_set_master()' function using the '__weak'
attribute which can be used by all architectures as a default which,
if necessary, can then be over-ridden by architecture-specific code.
No functional change.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These new PCI services allow to probe for 2.3-compliant INTx masking
support and then use the feature from PCI interrupt handlers. The
services are properly synchronized with concurrent config space access
via sysfs or on device reset.
This enables generic PCI device drivers like uio_pci_generic or KVM's
device assignment to implement the necessary kernel-side IRQ handling
without any knowledge about device-specific interrupt status and control
registers.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_block_user_cfg_access was designed for the use case that a single
context, the IPR driver, temporarily delays user space accesses to the
config space via sysfs. This assumption became invalid by the time
pci_dev_reset was added as locking instance. Today, if you run two loops
in parallel that reset the same device via sysfs, you end up with a
kernel BUG as pci_block_user_cfg_access detect the broken assumption.
This reworks the pci_block_user_cfg_access to a sleeping service
pci_cfg_access_lock and an atomic-compatible variant called
pci_cfg_access_trylock. The former not only blocks user space access as
before but also waits if access was already locked. The latter service
just returns false in this case, allowing the caller to resolve the
conflict instead of raising a BUG.
Adaptions of the ipr driver were originally written by Brian King.
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Include the driver name and device in warning when a pci driver
supports both legacy pm and new framework as just the stack trace
gives no way to identify the driver.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I traced a nasty kexec on panic boot failure to the fact that we had
screaming msi interrupts and we were not disabling the msi messages at
kernel startup. The booting kernel had not enabled those interupts so
was not prepared to handle them.
I can see no reason why we would ever want to leave the msi interrupts
enabled at boot if something else has enabled those interrupts. The pci
spec specifies that msi interrupts should be off by default. Drivers
are expected to enable the msi interrupts if they want to use them. Our
interrupt handling code reprograms the interrupt handlers at boot and
will not be be able to do anything useful with an unexpected interrupt.
This patch applies cleanly all of the way back to 2.6.32 where I noticed
the problem.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Modify pci_acpi_wake_dev() to avoid resuming PME-capable devices
whose PME Status bits are not set, which may happen currently if
several devices are associated with the same wakeup GPE and all
of them are notified whenever at least one of them signals PME.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use non-ordered workqueue for attention button events.
Attention button events on each slot can be handled asynchronously. So
we should use non-ordered workqueue. This patch also removes ordered
workqueue in pciehp as a result.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix improper workqueue cleanup.
In the current pciehp, pcied_cleanup() calls destroy_workqueue()
before calling pcie_port_service_unregister(). This causes kernel oops
because flush_workqueue() is called in the pcie_port_service_unregister()
code path after the workqueue was destroyed. So pcied_cleanup() must call
pcie_port_service_unregister() first before calling destroy_workqueue().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Right now we forcibly clear ASPM state on all devices if the BIOS indicates
that the feature isn't supported. Based on the Microsoft presentation
"PCI Express In Depth for Windows Vista and Beyond", I'm starting to think
that this may be an error. The implication is that unless the platform
grants full control via _OSC, Windows will not touch any PCIe features -
including ASPM. In that case clearing ASPM state would be an error unless
the platform has granted us that control.
This patch reworks the ASPM disabling code such that the actual clearing
of state is triggered by a successful handoff of PCIe control to the OS.
The general ASPM code undergoes some changes in order to ensure that the
ability to clear the bits isn't overridden by ASPM having already been
disabled. Further, this theoretically now allows for situations where
only a subset of PCIe roots hand over control, leaving the others in the
BIOS state.
It's difficult to know for sure that this is the right thing to do -
there's zero public documentation on the interaction between all of these
components. But enough vendors enable ASPM on platforms and then set this
bit that it seems likely that they're expecting the OS to leave them alone.
Measured to save around 5W on an idle Thinkpad X220.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These are extended capabilities, rename and move to proper
group for consistency.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds a per-pci-device subdirectory in sysfs called:
/sys/bus/pci/devices/<device>/msi_irqs
This sub-directory exports the set of msi vectors allocated by a given
pci device, by creating a numbered sub-directory for each vector beneath
msi_irqs. For each vector various attributes can be exported.
Currently the only attribute is called mode, which tracks the
operational mode of that vector (msi vs. msix)
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
security_capable takes ns, cred, cap. But the LSM capable() hook takes
cred, ns, cap. The capability helper functions also take cred, ns, cap.
Rather than flip argument order just to flip it back, leave them alone.
Heck, this should be a little faster since argument will be in the right
place!
Signed-off-by: Eric Paris <eparis@redhat.com>
The 'name', 'owner', and 'mod_name' members are redundant with the
identically named fields in the 'driver' sub-structure. Rather than
switching each instance to specify these fields explicitly, introduce
a macro to simplify this.
Eliminate further redundancy by allowing the drvname argument to
DEFINE_XENBUS_DRIVER() to be blank (in which case the first entry from
the ID table will be used for .driver.name).
Also eliminate the questionable xenbus_register_{back,front}end()
wrappers - their sole remaining purpose was the checking of the
'owner' field, proper setting of which shouldn't be an issue anymore
when the macro gets used.
v2: Restore DRV_NAME for the driver name in xen-pciback.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
I noticed that hotplug of one setup does not work with recent change in
pci tree.
After checking the bridge conf setup, I noticed that the bridges get
assigned but do not get enabled.
The reason is the following commit, while simply ignores bridge
resources when enabling a pci device:
| commit bbef98ab0f
| Author: Ram Pai <linuxram@us.ibm.com>
| Date: Sun Nov 6 10:33:10 2011 +0800
|
| PCI: defer enablement of SRIOV BARS
|...
| NOTE: Note, there is subtle change in the pci_enable_device() API. Any
| driver that depends on SRIOV BARS to be enabled in pci_enable_device()
| can fail.
Put back bridge resource and ROM resource checking to fix the problem.
That should fix regression like BIOS does not assign correct resource to
bridge.
Discussion can be found at:
http://www.spinics.net/lists/linux-pci/msg12874.html
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During test of one IB card with guest VM, found that, msi is not
initialized properly.
It turns out __write_msi_msg will do nothing if device current_state is
not PCI_D0. And, that pci device does not have pm_cap in guest VM.
There is an error in setting of power state to PCI_D0 in
pci_enable_device(), but error is not returned for this. Following is
code flow:
pci_enable_device() --> __pci_enable_device_flags() -->
do_pci_enable_device() --> pci_set_power_state() -->
__pci_start_power_transition()
We have following condition inside __pci_start_power_transition():
if (platform_pci_power_manageable(dev)) {
error = platform_pci_set_power_state(dev, state);
if (!error)
pci_update_current_state(dev, state);
} else {
error = -ENODEV;
/* Fall back to PCI_D0 if native PM is not supported */
if (!dev->pm_cap)
dev->current_state = PCI_D0;
}
Here, from platform_pci_set_power_state(), acpi_pci_set_power_state() is
getting called and that is failing with ENODEV because of following
condition:
if (!handle || ACPI_SUCCESS(acpi_get_handle(handle, "_EJ0",&tmp)))
return -ENODEV;
Because of that, pci_update_current_state() is not getting called.
With this patch, if device power state can not be set via
platform_pci_set_power_state and that device does not have native pm
support, then PCI device power state will be set to PCI_D0.
-v2: This also reverts 47e9037ac1, as it's
not needed after this change.
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ajaykumar Hotchandani<ajaykumar.hotchandani@oracle.com>
Signed-off-by: Yinghai Lu<yinghai.lu@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 0d52f54e2e (PCI / ACPI: Make
acpiphp ignore root bridges using PCIe native hotplug) added code
that made the acpiphp driver completely ignore PCIe root complexes
for which the kernel had been granted control of the native PCIe
hotplug feature by the BIOS through _OSC. Unfortunately, however,
this was a mistake, because on some systems there were PCI bridges
supporting PCI (non-PCIe) hotplug under such root complexes and
those bridges should have been handled by acpiphp.
For this reason, revert the changes made by the commit mentioned
above and make register_slot() in drivers/pci/hotplug/acpiphp_glue.c
avoid registering hotplug slots for PCIe ports that belong to
root complexes with native PCIe hotplug enabled (which means that
the BIOS has granted the kernel control of this feature for the
given root complex). This is reported to address the original
issue fixed by commit 0d52f54e2e and
to work on the system where that commit broke things.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This adjusts PCI_IOAPIC to be user configurable (possibly as a
module) on x86, since the base architecture code for adding
IO-APICs dynamically isn't there yet (and hence having the code
present everywhere is pretty pointless).
To make this consistent, a MODULE_DEVICE_TABLE() declaration
gets added, the class specifications get corrected (by properly
using PCI_DEVICE_CLASS() intended for purposes like this), and
the probe and remove functions get their sections adjusted.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/4EDDD71A02000078000659F1@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I get this compile failure on parisc:
drivers/pci/ats.c: In function 'ats_alloc_one':
drivers/pci/ats.c:29: error: implicit declaration of function 'kzalloc'
drivers/pci/ats.c:29: warning: assignment makes pointer from integer without a cast
drivers/pci/ats.c: In function 'ats_free_one':
drivers/pci/ats.c:45: error: implicit declaration of function 'kfree'
Because ats.c is missing linux/slab.h as an include. This patch fixes it
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All the PCI BARs of a device are enabled when the device is enabled
using pci_enable_device(). This unnecessarily enables SRIOV BARs of the
device.
On some platforms, which do not support SRIOV as yet, the
pci_enable_device() fails to enable the device if its SRIOV BARs are not
allocated resources correctly.
The following patch fixes the above problem. The SRIOV BARs are now
enabled when IOV capability of the device is enabled in sriov_enable().
NOTE: Note, there is subtle change in the pci_enable_device() API. Any
driver that depends on SRIOV BARS to be enabled in pci_enable_device()
can fail.
The patch has been touch tested on power and x86 platform.
Tested-by: Michael Wang <wangyun@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
More consistency cleanups. Drop the _OFF, separate and indent
CTRL/CAP/STATUS bit definitions. This helped find the previous
mis-use of bit 0 in the PASID capability register.
Reviewed-by: Joerg Roedel <joerg.roedel@amd.com>
Tested-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PASID ECN indicates bit 0 is reserved in the capability register.
Switch pci_enable_pasid() to error if PASID is already enabled and
don't expose enable as a feature in pci_pasid_features().
Reviewed-by: Joerg Roedel <joerg.roedel@amd.com>
Tested-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I traced a nasty kexec on panic boot failure to the fact that we had
screaming msi interrupts and we were not disabling the msi messages at
kernel startup. The booting kernel had not enabled those interupts so
was not prepared to handle them.
I can see no reason why we would ever want to leave the msi interrupts
enabled at boot if something else has enabled those interrupts. The pci
spec specifies that msi interrupts should be off by default. Drivers
are expected to enable the msi interrupts if they want to use them. Our
interrupt handling code reprograms the interrupt handlers at boot and
will not be be able to do anything useful with an unexpected interrupt.
This patch applies cleanly all of the way back to 2.6.32 where I noticed
the problem.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Modify pci_acpi_wake_dev() to avoid resuming PME-capable devices
whose PME Status bits are not set, which may happen currently if
several devices are associated with the same wakeup GPE and all
of them are notified whenever at least one of them signals PME.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the kernel has requested control of the SHPC native hotplug
feature for a given root bridge, the acpiphp driver should not try
to handle that root bridge and it should leave it to shpchp.
Failing to do so causes problems to happen if shpchp is loaded
and unloaded before loading acpiphp (ACPI-based hotplug won't work
in that case anyway).
To address this issue make find_root_bridges() ignore PCI root
bridges with SHPC native hotplug enabled and make add_bridge()
return error code if SHPC native hotplug is enabled for the given
root bridge. This causes acpiphp to refuse to load if SHPC native
hotplug is enabled for all root bridges and to refuse binding to
the root bridges with SHPC native hotplug enabled.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use non-ordered workqueue for attention button events.
Attention button events on each slot can be handled asynchronously. So
we should use non-ordered workqueue. This patch also removes ordered
workqueue in pciehp as a result.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix improper workqueue cleanup.
In the current pciehp, pcied_cleanup() calls destroy_workqueue()
before calling pcie_port_service_unregister(). This causes kernel oops
because flush_workqueue() is called in the pcie_port_service_unregister()
code path after the workqueue was destroyed. So pcied_cleanup() must call
pcie_port_service_unregister() first before calling destroy_workqueue().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Right now we forcibly clear ASPM state on all devices if the BIOS indicates
that the feature isn't supported. Based on the Microsoft presentation
"PCI Express In Depth for Windows Vista and Beyond", I'm starting to think
that this may be an error. The implication is that unless the platform
grants full control via _OSC, Windows will not touch any PCIe features -
including ASPM. In that case clearing ASPM state would be an error unless
the platform has granted us that control.
This patch reworks the ASPM disabling code such that the actual clearing
of state is triggered by a successful handoff of PCIe control to the OS.
The general ASPM code undergoes some changes in order to ensure that the
ability to clear the bits isn't overridden by ASPM having already been
disabled. Further, this theoretically now allows for situations where
only a subset of PCIe roots hand over control, leaving the others in the
BIOS state.
It's difficult to know for sure that this is the right thing to do -
there's zero public documentation on the interaction between all of these
components. But enough vendors enable ASPM on platforms and then set this
bit that it seems likely that they're expecting the OS to leave them alone.
Measured to save around 5W on an idle Thinkpad X220.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These are extended capabilities, rename and move to proper
group for consistency.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds a per-pci-device subdirectory in sysfs called:
/sys/bus/pci/devices/<device>/msi_irqs
This sub-directory exports the set of msi vectors allocated by a given
pci device, by creating a numbered sub-directory for each vector beneath
msi_irqs. For each vector various attributes can be exported.
Currently the only attribute is called mode, which tracks the
operational mode of that vector (msi vs. msix)
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI hotplug: shpchp: don't blindly claim non-AMD 0x7450 device IDs
PCI: pciehp: wait 100 ms after Link Training check
PCI: pciehp: wait 1000 ms before Link Training check
PCI: pciehp: Retrieve link speed after link is trained
PCI: Let PCI_PRI depend on PCI
PCI: Fix compile errors with PCI_ATS and !PCI_IOV
PCI / ACPI: Make acpiphp ignore root bridges using PCIe native hotplug
Previously we claimed device ID 0x7450, regardless of the vendor, which is
clearly wrong. Now we'll claim that device ID only for AMD.
I suspect this was just a typo in the original code, but it's possible this
change will break shpchp on non-7450 AMD bridges. If so, we'll have to fix
them as we find them.
Reference: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=638863
Reported-by: Ralf Jung <ralfjung-e@gmx.de>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the port supports Link speeds greater than 5.0 GT/s, we must wait
for 100 ms after Link training completes before sending configuration
request.
Acked-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We need to wait for 1000 ms after Data Link Layer Link Active (DLLLA)
bit reads 1b before sending configuration request. Currently pciehp
does this wait after checking Link Training (LT) bit. But we need it
before checking LT bit because LT is still set even after DLLLA bit is
set on some platforms.
Acked-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During hot plug, board_added will call pciehp_power_on_slot().
But link speed is updated in pciehp_power_on_slot().
We should not update link speed there, because that is too early.
So move the link speed update to pciehp_check_link_status() after making
sure the link has been trained.
-v2: fix compile warning that Kenji found.
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scsi: drop unused Kconfig symbol
pci: drop unused Kconfig symbol
stmmac: drop unused Kconfig symbol
x86: drop unused Kconfig symbol
powerpc: drop unused Kconfig symbols
powerpc: 40x: drop unused Kconfig symbol
mips: drop unused Kconfig symbols
openrisc: drop unused Kconfig symbols
arm: at91: drop unused Kconfig symbol
samples: drop unused Kconfig symbol
m32r: drop unused Kconfig symbol
score: drop unused Kconfig symbols
sh: drop unused Kconfig symbol
um: drop unused Kconfig symbol
sparc: drop unused Kconfig symbol
alpha: drop unused Kconfig symbol
Fix up trivial conflict in drivers/net/ethernet/stmicro/stmmac/Kconfig
as per Michal: the STMMAC_DUAL_MAC config variable is still unused and
should be deleted.
These were getting module.h implicitly from device.h but we want
to clean that up, so we fix it here to avoid things like:
pci/slot.c: In function ‘pci_hp_create_module_link’:
pci/slot.c:383: error: ‘module_kset’ undeclared (first use in this function)
Similarly, rpadlpar_core.c is modular, so add module.h to its includes.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
They were implicitly getting it from device.h --> module.h but
we want to clean that up. So add the minimal header for these
macros.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There's no other Kconfig symbol that depends on XEN_PCIDEV_FE_DEBUG.
Neither is there anything that uses CONFIG_XEN_PCIDEV_FE_DEBUG.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
This avoids the PCI_PRI question in 'make config' when PCI
is not selected.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the kernel has requested control of the PCIe native hotplug
feature for a given root complex, the acpiphp driver should not try
to handle that root complex and it should leave it to pciehp.
Failing to do so causes problems to happen if acpiphp is loaded
before pciehp on such systems.
To address this issue make find_root_bridges() ignore PCIe root
complexes with PCIe native hotplug enabled and make add_bridge()
return error code if PCIe native hotplug is enabled for the given
root port. This causes acpiphp to refuse to load if PCIe native
hotplug is enabled for all complexes and to refuse binding to
the root complexes with PCIe native hotplug is enabled.
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Clean-up MPS debug output
pci: Clamp pcie_set_readrq() when using "performance" settings
PCI: enable MPS "performance" setting to properly handle bridge MPS
PCI: Workaround for Intel MPS errata
PCI: Add support for PASID capability
PCI: Add implementation for PRI capability
PCI: Export ATS functions to modules
PCI: Move ATS implementation into own file
PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
PCI / PM: Extend PME polling to all PCI devices
PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
PCI: Make pci_setup_bridge() non-static for use by arch code
x86: constify PCI raw ops structures
PCI: Add quirk for known incorrect MPSS
PCI: Add Solarflare vendor ID and SFC4000 device IDs
Clean-up MPS debug output to make it a single line and aligned, thus
making it more readable for a large number of buses and devices in a
single system.
Suggested by Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When configuring the PCIe settings for "performance", we allow parents
to have a larger Max Payload Size than children and rely on children
Max Read Request Size to not be larger than their own MPS to avoid
having the host bridge generate responses they can't cope with.
However, various drivers in Linux call pci_set_readrq() with arbitrary
values, assuming this to be a simple performance tweak. This breaks
under our "performance" configuration.
Fix that by making sure the value programmed by pcie_set_readrq() is
never larger than the configured MPS for that device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rework the "performance" MPS option to configure the device MPS with the
smaller of the device MPSS or the bridge MPS (which is assumed to be
properly configured at this point to the largest allowable MPS based on
its parent bus).
Also, rework the MRRS setting to report an inability to set the MRRS to
a valid setting.
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, ioapic: Consolidate the explicit EOI code
x86, ioapic: Restore the mask bit correctly in eoi_ioapic_irq()
x86, kdump, ioapic: Reset remote-IRR in clear_IO_APIC
iommu: Rename the DMAR and INTR_REMAP config options
x86, ioapic: Define irq_remap_modify_chip_defaults()
x86, msi, intr-remap: Use the ioapic set affinity routine
iommu: Cleanup ifdefs in detect_intel_iommu()
iommu: No need to set dmar_disabled in check_zero_address()
iommu: Move IOMMU specific code to intel-iommu.c
intr_remap: Call dmar_dev_scope_init() explicitly
x86, x2apic: Enable the bios request for x2apic optout
* 'stable/drivers-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus: don't rely on xen_initial_domain to detect local xenstore
xenbus: Fix loopback event channel assuming domain 0
xen/pv-on-hvm:kexec: Fix implicit declaration of function 'xen_hvm_domain'
xen/pv-on-hvm kexec: add xs_reset_watches to shutdown watches from old kernel
xen/pv-on-hvm kexec: update xs_wire.h:xsd_sockmsg_type from xen-unstable
xen/pv-on-hvm kexec+kdump: reset PV devices in kexec or crash kernel
xen/pv-on-hvm kexec: rebind virqs to existing eventchannel ports
xen/pv-on-hvm kexec: prevent crash in xenwatch_thread() when stale watch events arrive
* 'stable/drivers.bugfixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Check if the device is found instead of blindly assuming so.
xen/pciback: Do not dereference psdev during printk when it is NULL.
xen: remove XEN_PLATFORM_PCI config option
xen: XEN_PVHVM depends on PCI
xen/pciback: double lock typo
xen/pciback: use mutex rather than spinlock in vpci backend
xen/pciback: Use mutexes when working with Xenbus state transitions.
xen/pciback: miscellaneous adjustments
xen/pciback: use mutex rather than spinlock in passthrough backend
xen/pciback: use resource_size()
* 'stable/pci.fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: support multi-segment systems
xen-swiotlb: When doing coherent alloc/dealloc check before swizzling the MFNs.
xen/pci: make bus notifier handler return sane values
xen-swiotlb: fix printk and panic args
xen-swiotlb: Fix wrong panic.
xen-swiotlb: Retry up three times to allocate Xen-SWIOTLB
xen-pcifront: Update warning comment to use 'e820_host' option.
Devices supporting Process Address Space Identifiers
(PASIDs) can use an IOMMU to access multiple IO address
spaces at the same time. A PCIe device indicates support for
this feature by implementing the PASID capability. This
patch adds support for the capability to the Linux kernel.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Implement the necessary functions to handle PRI capabilities
on PCIe devices. With PRI devices behind an IOMMU can signal
page fault conditions to software and recover from such
faults.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes the ATS functions usable for modules.
They will be used by a module implementing some advanced
AMD IOMMU features.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ATS does not depend on IOV support, so move the code into
its own file. This file will also include support for the
PRI and PASID capabilities later.
Also give ATS its own Kconfig variable to allow selecting it
without IOV support.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The result returned by acpi_dev_run_wake() is always either -EINVAL
or -ENODEV, while obviously it should return 0 on success. The
problem is that the leftover error variable, that's not really used
in the function, is initialized with -ENODEV and then returned
without modification.
To fix this issue remove the error variable from acpi_dev_run_wake()
and make the function return 0 on success as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I originally submitted a patch to workaround this by pushing all Ejection
Requests and Device Checks onto the kacpi_hotplug queue.
http://marc.info/?l=linux-acpi&m=131678270930105&w=2
The patch is still insufficient in that Bus Checks also need to be added.
Rather than add all events, including non-PCI-hotplug events, to the
hotplug queue, mjg suggested that a better approach would be to modify
the acpiphp driver so only acpiphp events would be added to the
kacpi_hotplug queue.
It's a longer patch, but at least we maintain the benefit of having separate
queues in ACPI. This, of course, is still only a workaround the problem.
As Bjorn and mjg pointed out, we have to refactor a lot of this code to do
the right thing but at this point it is a better to have this code working.
The acpi core places all events on the kacpi_notify queue. When the acpiphp
driver is loaded and a PCI card with a PCI-to-PCI bridge is removed the
following call sequence occurs:
cleanup_p2p_bridge()
-> cleanup_bridge()
-> acpi_remove_notify_handler()
-> acpi_os_wait_events_complete()
-> flush_workqueue(kacpi_notify_wq)
which is the queue we are currently executing on and the process will hang.
Move all hotplug acpiphp events onto the kacpi_hotplug workqueue. In
handle_hotplug_event_bridge() and handle_hotplug_event_func() we can simply
push the rest of the work onto the kacpi_hotplug queue and then avoid the
deadlock.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: mjg@redhat.com
Cc: bhelgaas@google.com
Cc: linux-acpi@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The land of PCI power management is a land of sorrow and ugliness,
especially in the area of signaling events by devices. There are
devices that set their PME Status bits, but don't really bother
to send a PME message or assert PME#. There are hardware vendors
who don't connect PME# lines to the system core logic (they know
who they are). There are PCI Express Root Ports that don't bother
to trigger interrupts when they receive PME messages from the devices
below. There are ACPI BIOSes that forget to provide _PRW methods for
devices capable of signaling wakeup. Finally, there are BIOSes that
do provide _PRW methods for such devices, but then don't bother to
call Notify() for those devices from the corresponding _Lxx/_Exx
GPE-handling methods. In all of these cases the kernel doesn't have
a chance to receive a proper notification that it should wake up a
device, so devices stay in low-power states forever. Worse yet, in
some cases they continuously send PME Messages that are silently
ignored, because the kernel simply doesn't know that it should clear
the device's PME Status bit.
This problem was first observed for "parallel" (non-Express) PCI
devices on add-on cards and Matthew Garrett addressed it by adding
code that polls PME Status bits of such devices, if they are enabled
to signal PME, to the kernel. Recently, however, it has turned out
that PCI Express devices are also affected by this issue and that it
is not limited to add-on devices, so it seems necessary to extend
the PME polling to all PCI devices, including PCI Express and planar
ones. Still, it would be wasteful to poll the PME Status bits of
devices that are known to receive proper PME notifications, so make
the kernel (1) poll the PME Status bits of all PCI and PCIe devices
enabled to signal PME and (2) disable the PME Status polling for
devices for which correct PME notifications are received.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 15bed0f2f added a quirk for the e823 Ricoh card reader to lower the
base frequency. However, the quirk first checks to see if the proprietary
MMC controller is disabled, and returns if so. On some devices, such as the
Lenovo X220, the MMC controller is already disabled by firmware it seems,
but the frequency change is still needed so sdhci-pci can talk to the cards.
Since the MMC controller is disabled, the frequency fixup was never being run
on these machines.
This moves the e823 check above the MMC controller check so that it always
gets run.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=722509
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The "powernv" platform of the powerpc architecture needs to assign PCI
resources using a specific algorithm to fit some HW constraints of
the IBM "IODA" architecture (related to the ability to create error
handling domains that encompass specific segments of MMIO space).
For doing so, it wants to call pci_setup_bridge() from architecture
specific resource management in order to configure bridges after all
resources have been assigned. So make it non-static.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Using legacy interrupts and TLPs > 256 bytes on the SFC4000 (all
revisions) may cause interrupt messages to be replayed. In some
systems this results in a non-recoverable MCE. Early boards using the
SFC4000 set the maximum payload size supported (MPSS) to 1024 bytes
and we should override that.
There are probably other devices with similar issues, so give this
quirk a generic name.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults. Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.
Also, add the option for peer to peer DMA MPS configuration. Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another. To work around this, simply make the system
wide MPS the smallest possible value (128B).
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In pcie_find_smpss(), we have the following statement:
if (dev->is_hotplug_bridge && (!list_is_singular(&dev->bus->devices) ||
dev->bus->self->pcie_type != PCI_EXP_TYPE_ROOT_PORT))
The problem is that at least on my machine, this gets called for the
root complex (virtual P2P bridge), and dev->bus->self is NULL since
the parent bus for this is not itself anchor to a PCI device.
This adds the necessary NULL check.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jon Mason <mason@myri.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has
massive negative ramifications on some devices. Without knowing which
devices have this issue, do not modify from the default value when
walking the PCI-E bus in pcie_bus_safe mode. Also, make pcie_bus_safe
the default procedure.
Tested-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Simon Kirby <sim@hostway.ca>
Tested-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-and-tested-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
References: https://bugzilla.kernel.org/show_bug.cgi?id=42162
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b03e7495a8 ("PCI: Set PCI-E Max Payload Size on fabric")
introduced a potential NULL pointer dereference in calls to
pcie_bus_configure_settings due to attempts to access pci_bus self
variables when the self pointer is NULL.
To correct this, verify that the self pointer in pci_bus is non-NULL
before dereferencing it.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With Xen changeset 23428 "libxl: Add 'e820_host' option to config file"
the E820 as seen from the host can now be passed into the guest.
This means that a PV guest can now:
- Use the correct PCI I/O gap. Before these patches, Linux guest would
boot up and would tell:
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:c0000000)
while in actuality the PCI I/O gap should have been:
[ 0.000000] Allocating PCI resources starting at b0000000 (gap: b0000000:4c000000)
- The PV domain with PCI devices was limited to 3GB. It now can be booted
with 4GB, 8GB, or whatever number you want. The PCI devices will now _not_ conflict
with System RAM. Meaning the drivers can load.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: linux-pci@vger.kernel.org
CC: stable@kernel.org
[v2: Made the string less broken up. Suggested by Joe Perches]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fix new kernel-doc warning in pci.c:
Warning(drivers/pci/pci.c:3259): No description found for parameter 'mps'
Warning(drivers/pci/pci.c:3259): Excess function parameter 'rq' description in 'pcie_set_mps'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: OF: Don't crash when bridge parent is NULL.
PCI: export pcie_bus_configure_settings symbol
PCI: code and comments cleanup
PCI: make cardbus-bridge resources optional
PCI: make SRIOV resources optional
PCI : ability to relocate assigned pci-resources
PCI: honor child buses add_size in hot plug configuration
PCI: Set PCI-E Max Payload Size on fabric
In pcibios_get_phb_of_node(), we will crash while booting if
bus->bridge->parent is NULL.
Check for this case and avoid dereferencing the NULL pointer.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (28 commits)
ACPI: delete stale reference in kernel-parameters.txt
ACPI: add missing _OSI strings
ACPI: remove NID_INVAL
thermal: make THERMAL_HWMON implementation fully internal
thermal: split hwmon lookup to a separate function
thermal: hide CONFIG_THERMAL_HWMON
ACPI print OSI(Linux) warning only once
ACPI: DMI workaround for Asus A8N-SLI Premium and Asus A8N-SLI DELUX
ACPI / Battery: propagate sysfs error in acpi_battery_add()
ACPI / Battery: avoid acpi_battery_add() use-after-free
ACPI: introduce "acpi_rsdp=" parameter for kdump
ACPI: constify ops structs
ACPI: fix CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS
ACPI: fix 80 char overflow
ACPI / Battery: Resolve the race condition in the sysfs_remove_battery()
ACPI / Battery: Add the check before refresh sysfs in the battery_notify()
ACPI / Battery: Add the hibernation process in the battery_notify()
ACPI / Battery: Rename acpi_battery_quirks2 with acpi_battery_quirks
ACPI / Battery: Change 16-bit signed negative battery current into correct value
ACPI / Battery: Add the power unit macro
...
pcie_bus_configure_settings needs to be exported if the PCI hotplug
driver is being compiled as a module.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
a) adjust_resource_sorted() is now called reassign_resource_sorted()
b) nice-to-have is now called optional
c) add_list is now called realloc_list.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Allocate resources to cardbus bridge only after all other genuine
resources requests are satisfied. Dont retry if resource allocation
for cardbus-bridges fail.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
From: Yinghai Lu <yinghai@kernel.org>
Allocate resources to SRIOV BARs only after all other required
resource-requests are satisfied. Dont retry if resource allocation for SRIOV
BARs fail.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently pci-bridges are allocated enough resources to satisfy their immediate
requirements. Any additional resource-requests fail if additional free space,
contiguous to the one already allocated, is not available. This behavior is not
reasonable since sufficient contiguous resources, that can satisfy the request,
are available at a different location.
This patch provides the ability to expand and relocate a allocated resource.
v2: Changelog: Fixed size calculation in pci_reassign_resource()
v3: Changelog : Split this patch. The resource.c changes are already
upstream. All the pci driver changes are in here.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
git commit c8adf9a3e8
"PCI: pre-allocate additional resources to devices only after
successful allocation of essential resources."
fails to take into consideration the optional-resources needed by children
devices while calculating the optional-resource needed by the bridge.
This can be a problem on some setup. For example, if a hotplug bridge has 8
children hotplug bridges, the bridge should have enough resources to accomodate
the hotplug requirements for each of its children hotplug bridges. Currently
this is not the case.
This patch fixes the problem.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
merge fchmod() and fchmodat() guts, kill ancient broken kludge
xfs: fix misspelled S_IS...()
xfs: get rid of open-coded S_ISREG(), etc.
vfs: document locking requirements for d_move, __d_move and d_materialise_unique
omfs: fix (mode & S_IFDIR) abuse
btrfs: S_ISREG(mode) is not mode & S_IFREG...
ima: fmode_t misspelled as mode_t...
pci-label.c: size_t misspelled as mode_t
jffs2: S_ISLNK(mode & S_IFMT) is pointless
snd_msnd ->mode is fmode_t, not mode_t
v9fs_iop_get_acl: get rid of unused variable
vfs: dont chain pipe/anon/socket on superblock s_inodes list
Documentation: Exporting: update description of d_splice_alias
fs: add missing unlock in default_llseek()
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
iommu/core: Fix build with INTR_REMAP=y && CONFIG_DMAR=n
iommu/amd: Don't use MSI address range for DMA addresses
iommu/amd: Move missing parts to drivers/iommu
iommu: Move iommu Kconfig entries to submenu
x86/ia64: intel-iommu: move to drivers/iommu/
x86: amd_iommu: move to drivers/iommu/
msm: iommu: move to drivers/iommu/
drivers: iommu: move to a dedicated folder
x86/amd-iommu: Store device alias as dev_data pointer
x86/amd-iommu: Search for existind dev_data before allocting a new one
x86/amd-iommu: Allow dev_data->alias to be NULL
x86/amd-iommu: Use only dev_data in low-level domain attach/detach functions
x86/amd-iommu: Use only dev_data for dte and iotlb flushing routines
x86/amd-iommu: Store ATS state in dev_data
x86/amd-iommu: Store devid in dev_data
x86/amd-iommu: Introduce global dev_data_list
x86/amd-iommu: Remove redundant device_flush_dte() calls
iommu-api: Add missing header file
Fix up trivial conflicts (independent additions close to each other) in
drivers/Makefile and include/linux/pci.h
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (51 commits)
PM: Improve error code of pm_notifier_call_chain()
PM: Add "RTC" to PM trace time stamps to avoid confusion
PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
PM / Suspend: Add .suspend_again() callback to suspend_ops
PM / OPP: Introduce function to free cpufreq table
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
...
* 'of-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
pci/of: Consolidate pci_bus_to_OF_node()
pci/of: Consolidate pci_device_to_OF_node()
x86/devicetree: Use generic PCI <-> OF matching
microblaze/pci: Move the remains of pci_32.c to pci-common.c
microblaze/pci: Remove powermac originated cruft
pci/of: Match PCI devices to OF nodes dynamically
I don't think there's enough value in the fact of a bridge window
being disabled to justify cluttering the dmesg log with it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
decode_bar() and pci_calc_resource_flags() both looked at the PCI BAR
type information, and it's simpler to just do it all in one place.
decode_bar() sets IORESOURCE_IO, IORESOURCE_MEM, and IORESOURCE_MEM_64
as appropriate, so res->flags contains all the information pci_bar_type
does, so we don't need to test the pci_bar_type return value.
decode_bar() used to return pci_bar_type, which we no longer need. We
can simplify it a bit by returning the struct resource flags rather than
updating them internally.
In pci_update_resource(), there's no need to decode the BAR type bits
again; we can just test for IORESOURCE_MEM_64 directly.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This fixes a minor regression where broken PCI devices that use the
reserved "11" memory BAR type worked before e354597cce but not after.
The low four bits of a memory BAR are "PTT0" where P=1 for prefetchable
BARs, and TT is as follows:
00 32-bit BAR, anywhere in lower 4GB
01 anywhere below 1MB (reserved as of PCI 2.2)
10 64-bit BAR
11 reserved
Prior to e354597cce, we treated "0100" as a 64-bit BAR and all others,
including prefetchable 64-bit BARs ("1100") as 32-bit BARs. The e354597cce
fix, which appeared in 2.6.28, treats "x1x0" as 64-bit BARs, so the
reserved "x110" types are treated as 64-bit instead of 32-bit.
This patch returns to treating the reserved "11" type as a 32-bit BAR and
adds a warning if we see it.
It also logs a note if we see a 1M BAR. This is not a warning, because
such hardware conforms to pre-PCI 2.2 spec, but I think it's worth noting
because Linux ignores the 1M restriction if it ever has to assign the BAR.
CC: Peter Chubb <peterc@gelato.unsw.edu.au>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35952
Reported-by: Jan Zwiegers <jan@radicalsystems.co.za>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When setting the PCI-E MRRS, pcie_set_readrq queries the current
settings via a pci_read_config_word call but writes the modified result
via a pci_write_config_dword. This results in writing 16 more bits than
were queried.
Also, the function description comment is slightly incorrect.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Naoki Yanagimoto reported that configuration read on some hot-added
PCIe device returns invalid value. This patch fixes this problem.
According to the PCIe spec, software must wait for at least 1 second
to judge if the hot-added device is broken after Data Link Layer State
Changed Event. This patch changes pciehp driver to wait for 1 second
after the Data Link Layer State Changed Event is detected before
initiating a configuration access instead of 100 ms.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Naoki Yanagimoto <yanagimoto@np.css.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The function pci_enable_ari() may mistakenly set the downstream port
of a v1 PCIe switch in ARI Forwarding mode. This is a PCIe v2 feature,
and with an SR-IOV device on that switch port believing the switch above
is ARI capable it may attempt to use functions 8-255, translating into
invalid (non-zero) device numbers for that bus. This has been seen
to cause Completion Timeouts and general misbehaviour including hangs
and panics.
Cc: stable@kernel.org
Acked-by: Don Dutile <ddutile@redhat.com>
Tested-by: Don Dutile <ddutile@redhat.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Aside of the usual motivation for constification, this function has a
history of being abused a hook for interrupt and other fixups so I turned
this function const ages ago in the MIPS code but it should be done
treewide.
Due to function pointer passing in varous places a few other functions
had to be constified as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To: Anton Vorontsov <avorontsov@mvista.com>
To: Chris Metcalf <cmetcalf@tilera.com>
To: Colin Cross <ccross@android.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
To: Eric Miao <eric.y.miao@gmail.com>
To: Erik Gilling <konkers@android.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
To: "H. Peter Anvin" <hpa@zytor.com>
To: Imre Kaloz <kaloz@openwrt.org>
To: Ingo Molnar <mingo@redhat.com>
To: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
To: Krzysztof Halasa <khc@pm.waw.pl>
To: Lennert Buytenhek <kernel@wantstofly.org>
To: Matt Turner <mattst88@gmail.com>
To: Nicolas Pitre <nico@fluxnic.net>
To: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
To: Richard Henderson <rth@twiddle.net>
To: Russell King <linux@arm.linux.org.uk>
To: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The driver reads PCI vendor ID from the PCI configuration register while it is
already stored by the PCI subsystem in the 'vendor' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The driver reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When hot-plugging a root bridge, we always prevent assigning a bus number
that already exists. This makes sure we don't step over an existing bus.
But sometimes we only remove PCI device in PCI hieratchy of OS, i,e.
echo 1 > /sys/bus/pci/devices/.../remove
but actually don't hotplug this device out the platform, so in this case
we still should re-scan this bus to enumerate this device when re-scanning
PCI again.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In addition to native PCIe AER, now APEI (ACPI Platform Error
Interface) GHES (Generic Hardware Error Source) can be used to report
PCIe AER errors too. To add support to APEI GHES PCIe AER recovery,
aer_recover_queue is added to export the recovery function in native
PCIe AER driver.
Recoverable PCIe AER errors are reported via NMI in APEI GHES. Then
APEI GHES uses irq_work to delay the error processing into an IRQ
handler. But PCIe AER recovery can be very time-consuming, so
aer_recover_queue, which can be used in IRQ handler, delays the real
recovery action into the process context, that is, work queue.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While it's declared static, etags points you to the wrong function
in drivers/acpi/dock.c and acpiphp_glue.c for example also makes
use of some (exported..) functions from this file.
If you trust etags and oversee the static declaration (what happened
to me) one gets totally confused...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ricoh 1180:e823 does not recognize certain types of SD/MMC cards,
as reported at http://launchpad.net/bugs/773524. Lowering the SD
base clock frequency from 200Mhz to 50Mhz fixes this issue. This
solution was suggest by Koji Matsumuro, Ricoh Company, Ltd.
This change has no negative performance effect on standard SD
cards, though it's quite possible that there will be one on
UHS-1 cards.
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Cc: Koji Matsumuro <matsumur@nts.ricoh.co.jp>
Cc: <stable@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Structs battery_file, acpi_dock_ops, file_operations,
thermal_cooling_device_ops, thermal_zone_device_ops, kernel_param_ops
are not changed in runtime. It is safe to make them const.
register_hotplug_dock_device() was altered to take const "ops" argument
to respect acpi_dock_ops' const notion.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* pm-runtime:
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Runtime: Consistent utilization of deferred_resume
PM / Runtime: Prevent runtime_resume from racing with probe
PM / Runtime: Replace "run-time" with "runtime" in documentation
PM / Runtime: Improve documentation of enable, disable and barrier
PM: Limit race conditions between runtime PM and system sleep (v2)
PCI / PM: Detect early wakeup in pci_pm_prepare()
PM / Runtime: Return special error code if runtime PM is disabled
PM / Runtime: Update documentation of interactions with system sleep
Multiple attempts to dynamically reallocate pci resources have
unfortunately lead to regressions. Though we continue to fix the
regressions and fine tune the dynamic-reallocation behavior, we have not
reached a acceptable state yet.
This patch provides a interim solution. It disables dynamic reallocation
by default, but adds the ability to enable it through pci=realloc kernel
command line parameter.
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A subsequent patch is going to move the invocation of
pm_runtime_barrier() from dpm_prepare() to __device_suspend().
Consequently, early wakeup events resulting from runtime resume
requests for wakeup devices queued up right before system suspend
will only be detected after all of the subsystem-level .prepare()
callbacks have run. However, the PCI bus type calls
pm_runtime_get_sync() from its pci_pm_prepare() callback routine,
so it would destroy the early wakeup events information regarding PCI
devices. To prevent this from happening add an early wakeup
detection mechanism, analogous to the one currently in dpm_prepare(),
to pci_pm_prepare().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Merriam-Webster tells us that the word exists. However ...
* Google suggests `forcibly' because it doesn't recognize `forcedly'.
* Google lists 494 thousand results for `forcedly'.
* Google lists 13.7 million results for `forcibly'.
* Linus's repo contains 1 occurrence of `forcedly' ( 0 after my change).
* Linus's repo contains 60 occurrences of `forcibly' (61 after my change).
Signed-off-by: Michael Witten <mfwitten@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: queue: bring discard_granularity/alignment into line with SCSI
mmc: queue: append partition subname to queue thread name
mmc: core: make erase timeout calculation allow for gated clock
mmc: block: switch card to User Data Area when removing the block driver
mmc: sdio: reset card during power_restore
mmc: cb710: fix #ifdef HAVE_EFFICIENT_UNALIGNED_ACCESS
mmc: sdhi: DMA slave ID 0 is invalid
mmc: tmio: fix regression in TMIO_MMC_WRPROTECT_DISABLE handling
mmc: omap_hsmmc: use original sg_len for dma_unmap_sg
mmc: omap_hsmmc: fix ocr mask usage
mmc: sdio: fix runtime PM path during driver removal
mmc: Add PCI fixup quirks for Ricoh 1180:e823 reader
mmc: sdhi: fix module unloading
mmc: of_mmc_spi: add NO_IRQ define to of_mmc_spi.c
mmc: vub300: fix null dereferences in error handling
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI/ACPI: fix type mismatch
PCI: fix new kernel-doc warning
PCI: Fix warning in drivers/pci/probe.c on sparc64
After commit e866500247
(PM: Allow pm_runtime_suspend() to succeed during system suspend) it
is possible that a device resumed by the pm_runtime_resume(dev) in
pci_pm_prepare() will be suspended immediately from a work item,
timer function or otherwise, defeating the very purpose of calling
pm_runtime_resume(dev) from there. To prevent that from happening
it is necessary to increment the runtime PM usage counter of the
device by replacing pm_runtime_resume() with pm_runtime_get_sync().
Moreover, the incremented runtime PM usage counter has to be
decremented by the corresponding pci_pm_complete(), via
pm_runtime_put_sync().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This should ease finding similarities with different platforms,
with the intention of solving problems once in a generic framework
which everyone can use.
Note: to move intel-iommu.c, the declaration of pci_find_upstream_pcie_bridge()
has to move from drivers/pci/pci.h to include/linux/pci.h. This is handled
in this patch, too.
As suggested, also drop DMAR's EXPERIMENTAL tag while we're at it.
Compile-tested on x86_64.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Compare only lower 32 bits of framebuffer map offsets
drm/i915: Don't leak in i915_gem_shmem_pread_slow()
drm/radeon/kms: do bounds checking for 3D_LOAD_VBPNTR and bump array limit
drm/radeon/kms: fix mac g5 quirk
x86/uv/x2apic: update for change in pci bridge handling.
alpha, drm: Remove obsolete Alpha support in MGA DRM code
alpha/drm: Cleanup Alpha support in DRM generic code
savage: remove unnecessary if statement
drm/radeon: fix GUI idle IH debug statements
drm/radeon/kms: check modes against max pixel clock
drm: fix fbs in DRM_IOCTL_MODE_GETRESOURCES ioctl
When I added 3448a19da4
I forgot about the special uv handling code for this, so this
patch fixes it up.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ingo Molnar
Signed-off-by: Dave Airlie <airlied@redhat.com>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32, leon: bugfix in LEON SMP interrupt init
sparc32, sun4m: bugfix in SMP IPI traphandler
sparc: Remove unnecessary semicolons
Add support for allocating irqs for bootbus devices
Do not skip interrupt sources in sun4d interrupt handler and acknowledge interrupts correctly
Restructure sun4d_build_device_irq so that timer interrupts can be allocated
sparc: PCIC_PCI needs SPARC32 dependency
sparc: Do not select GENERIC_HARDIRQS_NO_DEPRECATED
sparc32,leon: add GRPCI2 PCI Host driver
sparc32,leon: added LEON-common low-level PCI routines
sparc32: added CONFIG_PCIC_PCI Kconfig setting
