The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.
vaux2 is not used on Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VDVI power supply is no longer needed in
board code with the new DSS2 interface.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch corrects the LCD reset pin configuration.
Original code from early devkit8000 patch sets the TWL4030 GPIO_1
to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
disabled when other display is turned on.
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch corrects the DVI-D output setup of Devkit8000
Devkit8000 has different DVI reset pin with the BeagleBoard.
On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job.
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Corrected the wrong power supplies in devkit8000 code.
Add supply for ads7846 to support the new regulator framework for
touchscreen.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MACH_OMAP2_H4_USB1 doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MACH_OMAP_H4_OTG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
APM doesn't exist in Kconfig, therefore removing all references for it
from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LEDS_OMAP_DEBUG doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_DEBUG_LEDS from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_STI doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_DSP doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated to apply on top of already queued patches]
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_IR doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated for new mux code]
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_MUX_ERRORS doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_MUX_WARNINGS in the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we have to disable it manually to avoid compile errors.
Now it's only enabled only for the selected machines as suggested
by Anton Vorontsov <cbouatmailru@gmail.com>:
$ git grep VGA_CONSOLE= arch/arm/configs/
arch/arm/configs/footbridge_defconfig:CONFIG_VGA_CONSOLE=y
arch/arm/configs/integrator_defconfig:CONFIG_VGA_CONSOLE=y
arch/arm/configs/netwinder_defconfig:CONFIG_VGA_CONSOLE=y
Note that the Kconfig entry no longer needs separate entries
for ARCH_ACORN, ARCH_EBSA110 ARCH_VERSATILE.
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use new mux functions for that. There are no other known 2430 boards
that need this mux.
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the new mux function for that.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we get pin muxing out of plat-omap and can convert H4 to use the
new mux functions.
Note that it should be safe to assume we can mux all the keypad pins
except on H4 which may have Menelaus connected.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make omap2 FS USB code use new mux functions. Do not mux usb2_tllse0
as it has multiple options.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add data for 2430. Big thanks to Paul Walmsley <paul@pwsan.com>
for generating usable mux data out of TRMs.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add data for 2420. Big thanks to Paul Walmsley <paul@pwsan.com>
for generating usable mux data out of TRMs.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like 24xx uses mode3 instead of mode4 for muxable GPIO pins.
This will be needed when 24xx mux code is converted to use the new
mux functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omap2 FS USB platform init code into mach-omap2/usb-fs.c. This will
allow further work later on to use omap hwmod for initializing the
device.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to split old FS USB platform init code and stop doing pin multiplexing
under plat-omap. First move 24xx specific init code into omap2_usb[012]_init
functions.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (22 commits)
USB: gadget: f_mass_storage: stale common->fsg value bug fix
USB: gadget: f_mass_storage: fixed fs descriptors not being updated
USB: musb: Enable the maximum supported burst mode for DMA
USB: musb: fix Blackfin ulpi stubs
USB: MUSB: make non-OMAP platforms build with CONFIG_PM=y
USB: musb_core: make disconnect and suspend interrupts work again
USB: obey the sysfs power/wakeup setting
USB: gadget eth: Fix calculate CRC32 in EEM
USB: qcserial: fix a memory leak in qcprobe error path
USB: gadget/printer, fix sleep inside atomic
USB: isp1362-hcd, fix double lock
USB: serial: ftdi: correct merge conflict with CONTEC id
USB: fix oops in usb_sg_init()
USB: s3c2410: deactivate endpoints before gadget unbinding
USB: ehci-mxc: bail out on transceiver problems
USB: otg/ulpi: bail out on read errors
usb: musb: Fix a bug by making suspend interrupt available in device mode
USB: r8a66597: Fix failure in change of status
USB: xHCI: Fix bug in link TRB activation change.
USB: gadget: g_fs: possible invalid pointer reference bug fixed
...
As discussed with Mike Reed, add him as the maintainer of the qla1280
driver as I no longer have any hardware and he is actively looking
after it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
futex_find_get_task is currently used (through lookup_pi_state) from two
contexts, futex_requeue and futex_lock_pi_atomic. None of the paths
looks it needs the credentials check, though. Different (e)uids
shouldn't matter at all because the only thing that is important for
shared futex is the accessibility of the shared memory.
The credentail check results in glibc assert failure or process hang (if
glibc is compiled without assert support) for shared robust pthread
mutex with priority inheritance if a process tries to lock already held
lock owned by a process with a different euid:
pthread_mutex_lock.c:312: __pthread_mutex_lock_full: Assertion `(-(e)) != 3 || !robust' failed.
The problem is that futex_lock_pi_atomic which is called when we try to
lock already held lock checks the current holder (tid is stored in the
futex value) to get the PI state. It uses lookup_pi_state which in turn
gets task struct from futex_find_get_task. ESRCH is returned either
when the task is not found or if credentials check fails.
futex_lock_pi_atomic simply returns if it gets ESRCH. glibc code,
however, doesn't expect that robust lock returns with ESRCH because it
should get either success or owner died.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Darren Hart <dvhltc@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On fsg_unbind the common->fsg pointer was not NULLed if the
unbound fsg_dev instance was the current one. As an effect,
the incorrect pointer was preserved in all further operations
which caused do_set_interface to reference an invalid region.
This commit fixes this by raising an exception in fsg_bind
which will change the common->fsg pointer. This also requires
an wait queue so that the thread in fsg_bind can wait till the
worker thread handles the exception.
This commit removes also a config and new_config fields of
fsg_common as they are no longer needed since fsg can be
used to determine whether function is active or not.
Moreover, this commit removes possible race condition where
the fsg field was modified in both the worker thread and
form various other contexts. This is fixed by replacing
prev_fsg with new_fsg. At this point, fsg is assigned only
in worker thread.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The full speed descriptors were copied to the usb_function structure
in the fsg_bind_config function before call to the usb_ep_autoconfig.
The usb_ep_autoconfig was called in fsg_bind using the original
descriptors. In effect copied descriptors were not updated.
This patch changes the copy full speed descriptors after the call to
usb_op_autoconfig is performed. This way, copied full speed
descriptors have updated values.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Dries Van Puymbroeck <Dries.VanPuymbroeck@dekimo.com>
Tested-by: Dries Van Puymbroeck <Dries.VanPuymbroeck@dekimo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting MUSB Burst Mode 3 automatically enables support for
lower burst modes (BURST4, BURST8, BURST16 or bursts of unspecified
length). There is no need to set these burst modes based on the
packet size. Also enable the burst mode for both mode1 and mode0.
This is a fix for buggy hardware - having the lower burst modes
enabled can potentially cause lockups of the DMA engine used in
OMAP2/3/4 chips.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new ulpi code defines fallback stubs for the Blackfin arch, but does
so incorrectly leading to a build failure:
drivers/usb/musb/musb_core.c:227: error: 'musb_ulpi_read' undeclared here (not in a function)
drivers/usb/musb/musb_core.c:228: error: 'musb_ulpi_write' undeclared here (not in a function)
Tweak the fallback stubs so that they do work as intended.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
