For historical reasons, there are several timestamping selftest targets
in selftests/networking/timestamping. Move them to the standard
directory for networking tests: selftests/net.
Signed-off-by: Jian Yang <jianyang@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now a PHY-fixup in mach-imx set our rgmii timing correctly. For
the PHY KSZ9131 there is no PHY-fixup in mach-imx. To support this PHY
too, use rgmii-id.
For the now used KSZ9031 nothing will change, as rgmii-id is only
implemented and supported by the KSZ9131.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9131 provides DLL controlled delays on RXC and TXC lines. This
patch makes use of those delays. The information which delays should
be enabled or disabled comes from the interface names, documented in
ethernet-controller.yaml:
rgmii: Disable RXC and TXC delays
rgmii-id: Enable RXC and TXC delays
rgmii-txid: Enable only TXC delay, disable RXC delay
rgmii-rxid: Enable onlx RXC delay, disable TXC delay
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new netlink attribute to allow a user to (optionally)
specify the desired offload mode immediately upon MACSec link creation.
Separate iproute patch will be required to support this from user space.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge vm fixes from Andrew Morton:
"5 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/sparse: fix kernel crash with pfn_section_valid check
mm: fork: fix kernel_stack memcg stats for various stack implementations
hugetlb_cgroup: fix illegal access to memory
drivers/base/memory.c: indicate all memory blocks as removable
mm/swapfile.c: move inode_lock out of claim_swapfile
actually return nanoseconds and not the virtual clock value which
increments at 10e7 HZ (100ns).
-----BEGIN PGP SIGNATURE-----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=qZa/
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix for the Hyper-V clocksource driver to make sched clock
actually return nanoseconds and not the virtual clock value which
increments at 10e7 HZ (100ns)"
* tag 'timers-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/hyper-v: Make sched clock return nanoseconds correctly
-----BEGIN PGP SIGNATURE-----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=s1UQ
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single bugfix to prevent reference leaks in irq affinity notifiers"
* tag 'irq-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix reference leaks on irq affinity notifiers
Fix the crash like this:
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc000000000c3447c
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
CPU: 11 PID: 7519 Comm: lt-ndctl Not tainted 5.6.0-rc7-autotest #1
...
NIP [c000000000c3447c] vmemmap_populated+0x98/0xc0
LR [c000000000088354] vmemmap_free+0x144/0x320
Call Trace:
section_deactivate+0x220/0x240
__remove_pages+0x118/0x170
arch_remove_memory+0x3c/0x150
memunmap_pages+0x1cc/0x2f0
devm_action_release+0x30/0x50
release_nodes+0x2f8/0x3e0
device_release_driver_internal+0x168/0x270
unbind_store+0x130/0x170
drv_attr_store+0x44/0x60
sysfs_kf_write+0x68/0x80
kernfs_fop_write+0x100/0x290
__vfs_write+0x3c/0x70
vfs_write+0xcc/0x240
ksys_write+0x7c/0x140
system_call+0x5c/0x68
The crash is due to NULL dereference at
test_bit(idx, ms->usage->subsection_map);
due to ms->usage = NULL in pfn_section_valid()
With commit d41e2f3bd5 ("mm/hotplug: fix hot remove failure in
SPARSEMEM|!VMEMMAP case") section_mem_map is set to NULL after
depopulate_section_mem(). This was done so that pfn_page() can work
correctly with kernel config that disables SPARSEMEM_VMEMMAP. With that
config pfn_to_page does
__section_mem_map_addr(__sec) + __pfn;
where
static inline struct page *__section_mem_map_addr(struct mem_section *section)
{
unsigned long map = section->section_mem_map;
map &= SECTION_MAP_MASK;
return (struct page *)map;
}
Now with SPASEMEM_VMEMAP enabled, mem_section->usage->subsection_map is
used to check the pfn validity (pfn_valid()). Since section_deactivate
release mem_section->usage if a section is fully deactivated,
pfn_valid() check after a subsection_deactivate cause a kernel crash.
static inline int pfn_valid(unsigned long pfn)
{
...
return early_section(ms) || pfn_section_valid(ms, pfn);
}
where
static inline int pfn_section_valid(struct mem_section *ms, unsigned long pfn)
{
int idx = subsection_map_index(pfn);
return test_bit(idx, ms->usage->subsection_map);
}
Avoid this by clearing SECTION_HAS_MEM_MAP when mem_section->usage is
freed. For architectures like ppc64 where large pages are used for
vmmemap mapping (16MB), a specific vmemmap mapping can cover multiple
sections. Hence before a vmemmap mapping page can be freed, the kernel
needs to make sure there are no valid sections within that mapping.
Clearing the section valid bit before depopulate_section_memap enables
this.
[aneesh.kumar@linux.ibm.com: add comment]
Link: http://lkml.kernel.org/r/20200326133235.343616-1-aneesh.kumar@linux.ibm.comLink: http://lkml.kernel.org/r/20200325031914.107660-1-aneesh.kumar@linux.ibm.com
Fixes: d41e2f3bd5 ("mm/hotplug: fix hot remove failure in SPARSEMEM|!VMEMMAP case")
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Reviewed-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Wei Yang <richard.weiyang@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Depending on CONFIG_VMAP_STACK and the THREAD_SIZE / PAGE_SIZE ratio the
space for task stacks can be allocated using __vmalloc_node_range(),
alloc_pages_node() and kmem_cache_alloc_node().
In the first and the second cases page->mem_cgroup pointer is set, but
in the third it's not: memcg membership of a slab page should be
determined using the memcg_from_slab_page() function, which looks at
page->slab_cache->memcg_params.memcg . In this case, using
mod_memcg_page_state() (as in account_kernel_stack()) is incorrect:
page->mem_cgroup pointer is NULL even for pages charged to a non-root
memory cgroup.
It can lead to kernel_stack per-memcg counters permanently showing 0 on
some architectures (depending on the configuration).
In order to fix it, let's introduce a mod_memcg_obj_state() helper,
which takes a pointer to a kernel object as a first argument, uses
mem_cgroup_from_obj() to get a RCU-protected memcg pointer and calls
mod_memcg_state(). It allows to handle all possible configurations
(CONFIG_VMAP_STACK and various THREAD_SIZE/PAGE_SIZE values) without
spilling any memcg/kmem specifics into fork.c .
Note: This is a special version of the patch created for stable
backports. It contains code from the following two patches:
- mm: memcg/slab: introduce mem_cgroup_from_obj()
- mm: fork: fix kernel_stack memcg stats for various stack implementations
[guro@fb.com: introduce mem_cgroup_from_obj()]
Link: http://lkml.kernel.org/r/20200324004221.GA36662@carbon.dhcp.thefacebook.com
Fixes: 4d96ba3530 ("mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages")
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200303233550.251375-1-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This appears to be a mistake in commit faced7e080 ("mm: hugetlb
controller for cgroups v2").
Essentially that commit does a hugetlb_cgroup_from_counter assuming that
page_counter_try_charge has initialized counter.
But if that has failed then it seems will not initialize counter, so
hugetlb_cgroup_from_counter(counter) ends up pointing to random memory,
causing kasan to complain.
The solution is to simply use 'h_cg', instead of
hugetlb_cgroup_from_counter(counter), since that is a reference to the
hugetlb_cgroup anyway. After this change kasan ceases to complain.
Fixes: faced7e080 ("mm: hugetlb controller for cgroups v2")
Reported-by: syzbot+cac0c4e204952cf449b1@syzkaller.appspotmail.com
Signed-off-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Giuseppe Scrivano <gscrivan@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/20200313223920.124230-1-almasrymina@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We see multiple issues with the implementation/interface to compute
whether a memory block can be offlined (exposed via
/sys/devices/system/memory/memoryX/removable) and would like to simplify
it (remove the implementation).
1. It runs basically lockless. While this might be good for performance,
we see possible races with memory offlining that will require at
least some sort of locking to fix.
2. Nowadays, more false positives are possible. No arch-specific checks
are performed that validate if memory offlining will not be denied
right away (and such check will require locking). For example, arm64
won't allow to offline any memory block that was added during boot -
which will imply a very high error rate. Other archs have other
constraints.
3. The interface is inherently racy. E.g., if a memory block is detected
to be removable (and was not a false positive at that time), there is
still no guarantee that offlining will actually succeed. So any
caller already has to deal with false positives.
4. It is unclear which performance benefit this interface actually
provides. The introducing commit 5c755e9fd8 ("memory-hotplug: add
sysfs removable attribute for hotplug memory remove") mentioned
"A user-level agent must be able to identify which sections
of memory are likely to be removable before attempting the
potentially expensive operation."
However, no actual performance comparison was included.
Known users:
- lsmem: Will group memory blocks based on the "removable" property. [1]
- chmem: Indirect user. It has a RANGE mode where one can specify
removable ranges identified via lsmem to be offlined. However,
it also has a "SIZE" mode, which allows a sysadmin to skip the
manual "identify removable blocks" step. [2]
- powerpc-utils: Uses the "removable" attribute to skip some memory
blocks right away when trying to find some to offline+remove.
However, with ballooning enabled, it already skips this
information completely (because it once resulted in many false
negatives). Therefore, the implementation can deal with false
positives properly already. [3]
According to Nathan Fontenot, DLPAR on powerpc is nowadays no longer
driven from userspace via the drmgr command (powerpc-utils). Nowadays
it's managed in the kernel - including onlining/offlining of memory
blocks - triggered by drmgr writing to /sys/kernel/dlpar. So the
affected legacy userspace handling is only active on old kernels. Only
very old versions of drmgr on a new kernel (unlikely) might execute
slower - totally acceptable.
With CONFIG_MEMORY_HOTREMOVE, always indicating "removable" should not
break any user space tool. We implement a very bad heuristic now.
Without CONFIG_MEMORY_HOTREMOVE we cannot offline anything, so report
"not removable" as before.
Original discussion can be found in [4] ("[PATCH RFC v1] mm:
is_mem_section_removable() overhaul").
Other users of is_mem_section_removable() will be removed next, so that
we can remove is_mem_section_removable() completely.
[1] http://man7.org/linux/man-pages/man1/lsmem.1.html
[2] http://man7.org/linux/man-pages/man8/chmem.8.html
[3] https://github.com/ibm-power-utilities/powerpc-utils
[4] https://lkml.kernel.org/r/20200117105759.27905-1-david@redhat.com
Also, this patch probably fixes a crash reported by Steve.
http://lkml.kernel.org/r/CAPcyv4jpdaNvJ67SkjyUJLBnBnXXQv686BiVW042g03FUmWLXw@mail.gmail.com
Reported-by: "Scargall, Steve" <steve.scargall@intel.com>
Suggested-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Nathan Fontenot <ndfont@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Karel Zak <kzak@redhat.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200128093542.6908-1-david@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
claim_swapfile() currently keeps the inode locked when it is successful,
or the file is already swapfile (with -EBUSY). And, on the other error
cases, it does not lock the inode.
This inconsistency of the lock state and return value is quite confusing
and actually causing a bad unlock balance as below in the "bad_swap"
section of __do_sys_swapon().
This commit fixes this issue by moving the inode_lock() and IS_SWAPFILE
check out of claim_swapfile(). The inode is unlocked in
"bad_swap_unlock_inode" section, so that the inode is ensured to be
unlocked at "bad_swap". Thus, error handling codes after the locking now
jumps to "bad_swap_unlock_inode" instead of "bad_swap".
=====================================
WARNING: bad unlock balance detected!
5.5.0-rc7+ #176 Not tainted
-------------------------------------
swapon/4294 is trying to release lock (&sb->s_type->i_mutex_key) at: __do_sys_swapon+0x94b/0x3550
but there are no more locks to release!
other info that might help us debug this:
no locks held by swapon/4294.
stack backtrace:
CPU: 5 PID: 4294 Comm: swapon Not tainted 5.5.0-rc7-BTRFS-ZNS+ #176
Hardware name: ASUS All Series/H87-PRO, BIOS 2102 07/29/2014
Call Trace:
dump_stack+0xa1/0xea
print_unlock_imbalance_bug.cold+0x114/0x123
lock_release+0x562/0xed0
up_write+0x2d/0x490
__do_sys_swapon+0x94b/0x3550
__x64_sys_swapon+0x54/0x80
do_syscall_64+0xa4/0x4b0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f15da0a0dc7
Fixes: 1638045c36 ("mm: set S_SWAPFILE on blockdev swap devices")
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Qais Youef <qais.yousef@arm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200206090132.154869-1-naohiro.aota@wdc.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Fix memory leak in vti6, from Torsten Hilbrich.
2) Fix double free in xfrm_policy_timer, from YueHaibing.
3) NL80211_ATTR_CHANNEL_WIDTH attribute is put with wrong type, from
Johannes Berg.
4) Wrong allocation failure check in qlcnic driver, from Xu Wang.
5) Get ks8851-ml IO operations right, for real this time, from Marek
Vasut.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (22 commits)
r8169: fix PHY driver check on platforms w/o module softdeps
net: ks8851-ml: Fix IO operations, again
mlxsw: spectrum_mr: Fix list iteration in error path
qlcnic: Fix bad kzalloc null test
mac80211: set IEEE80211_TX_CTRL_PORT_CTRL_PROTO for nl80211 TX
mac80211: mark station unauthorized before key removal
mac80211: Check port authorization in the ieee80211_tx_dequeue() case
cfg80211: Do not warn on same channel at the end of CSA
mac80211: drop data frames without key on encrypted links
ieee80211: fix HE SPR size calculation
nl80211: fix NL80211_ATTR_CHANNEL_WIDTH attribute type
xfrm: policy: Fix doulbe free in xfrm_policy_timer
bpf: Explicitly memset some bpf info structures declared on the stack
bpf: Explicitly memset the bpf_attr structure
bpf: Sanitize the bpf_struct_ops tcp-cc name
vti6: Fix memory leak of skb if input policy check fails
esp: remove the skb from the chain when it's enqueued in cryptd_wq
ipv6: xfrm6_tunnel.c: Use built-in RCU list checking
xfrm: add the missing verify_sec_ctx_len check in xfrm_add_acquire
xfrm: fix uctx len check in verify_sec_ctx_len
...
Pull i2c fixes from Wolfram Sang:
"Three more driver bugfixes, and two doc improvements fixing build
warnings while we are here"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: pca-platform: Use platform_irq_get_optional
i2c: st: fix missing struct parameter description
i2c: nvidia-gpu: Handle timeout correctly in gpu_i2c_check_status()
i2c: fix a doc warning
i2c: hix5hd2: add missed clk_disable_unprepare in remove
Two small fixes, one in drivers (qla2xxx) and one in the core (sd) to
try to cope with USB enclosures that silently change reported
parameters.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXn9r4CYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishcRAAQCoW8Q2
raOl/SkEJ9CrqAsuav4B4HPl+B08wno3lHnp6wEA5Tkiw1aCLjqPBx/k0FctlRaD
wQIxxBD8dy47cFV/qfo=
=tWW/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes: one in drivers (qla2xxx), and one in the core (sd) to
try to cope with USB enclosures that silently change reported
parameters"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Fix optimal I/O size for devices that change reported values
scsi: qla2xxx: Fix I/Os being passed down when FC device is being deleted
The interrupt is not required so use platform_irq_get_optional() to
avoid error messages like
i2c-pca-platform 22080000.i2c: IRQ index 0 not found
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Daniel Borkmann says:
====================
pull-request: bpf 2020-03-27
The following pull-request contains BPF updates for your *net* tree.
We've added 3 non-merge commits during the last 4 day(s) which contain
a total of 4 files changed, 25 insertions(+), 20 deletions(-).
The main changes are:
1) Explicitly memset the bpf_attr structure on bpf() syscall to avoid
having to rely on compiler to do so. Issues have been noticed on
some compilers with padding and other oddities where the request was
then unexpectedly rejected, from Greg Kroah-Hartman.
2) Sanitize the bpf_struct_ops TCP congestion control name in order to
avoid problematic characters such as whitespaces, from Martin KaFai Lau.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Configure the MTU on DSA switches
This series adds support for configuring the MTU on front-panel switch
ports, while seamlessly adapting the CPU port and the DSA master to the
largest value plus the tagger overhead.
It also implements bridge MTU auto-normalization within the DSA core, as
resulted after the feedback of the implementation of this feature inside
the bridge driver in v2.
Support was added for quite a number of switches, in the hope that this
series would gain some traction:
- sja1105
- felix
- vsc73xx
- b53 and rest of the platform
V3 of this series was submitted here:
https://patchwork.ozlabs.org/cover/1262394/
V2 of this series was submitted here:
https://patchwork.ozlabs.org/cover/1261471/
V1 of this series was submitted here:
https://patchwork.ozlabs.org/cover/1199868/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the MTU for this switch means altering the
DEV_GMII:MAC_CFG_STATUS:MAC_MAXLEN_CFG field MAX_LEN, which in turn
limits the size of frames that can be received.
Special accounting needs to be done for the DSA CPU port (NPI port in
hardware terms). The NPI port configuration needs to be held inside the
private ocelot structure, since it is now accessed from multiple places.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of hardcoding the MTU to the maximum value allowed by the
hardware, obey the value known by the operating system.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On this switch, the frame length enforcements are performed by the
ingress policers. There are 2 types of those: regular L2 (also called
best-effort) and Virtual Link policers (an ARINC664/AFDX concept for
defining L2 streams with certain QoS abilities). To avoid future
confusion, I prefer to call the reset reason "Best-effort policers",
even though the VL policers are not yet supported.
We also need to change the setup of the initial static config, such that
DSA calls to .change_mtu (which are expensive) become no-ops and don't
reset the switch 5 times.
A driver-level decision is to unconditionally allow single VLAN-tagged
traffic on all ports. The CPU port must accept an additional VLAN header
for the DSA tag, which is again a driver-level decision.
The policers actually count bytes not only from the SDU, but also from
the Ethernet header and FCS, so those need to be accounted for as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the Broadcom switches supported by the b53 driver don't
support precise configuration of the MTU, but just a mumbo-jumbo boolean
flag. Set that.
Also configure BCM583XX devices to send and receive jumbo frames when
ports are configured with 10/100 Mbps speed.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many switches don't have an explicit knob for configuring the MTU
(maximum transmission unit per interface). Instead, they do the
length-based packet admission checks on the ingress interface, for
reasons that are easy to understand (why would you accept a packet in
the queuing subsystem if you know you're going to drop it anyway).
So it is actually the MRU that these switches permit configuring.
In Linux there only exists the IFLA_MTU netlink attribute and the
associated dev_set_mtu function. The comments like to play blind and say
that it's changing the "maximum transfer unit", which is to say that
there isn't any directionality in the meaning of the MTU word. So that
is the interpretation that this patch is giving to things: MTU == MRU.
When 2 interfaces having different MTUs are bridged, the bridge driver
MTU auto-adjustment logic kicks in: what br_mtu_auto_adjust() does is it
adjusts the MTU of the bridge net device itself (and not that of the
slave net devices) to the minimum value of all slave interfaces, in
order for forwarded packets to not exceed the MTU regardless of the
interface they are received and send on.
The idea behind this behavior, and why the slave MTUs are not adjusted,
is that normal termination from Linux over the L2 forwarding domain
should happen over the bridge net device, which _is_ properly limited by
the minimum MTU. And termination over individual slave devices is
possible even if those are bridged. But that is not "forwarding", so
there's no reason to do normalization there, since only a single
interface sees that packet.
The problem with those switches that can only control the MRU is with
the offloaded data path, where a packet received on an interface with
MRU 9000 would still be forwarded to an interface with MRU 1500. And the
br_mtu_auto_adjust() function does not really help, since the MTU
configured on the bridge net device is ignored.
In order to enforce the de-facto MTU == MRU rule for these switches, we
need to do MTU normalization, which means: in order for no packet larger
than the MTU configured on this port to be sent, then we need to limit
the MRU on all ports that this packet could possibly come from. AKA
since we are configuring the MRU via MTU, it means that all ports within
a bridge forwarding domain should have the same MTU.
And that is exactly what this patch is trying to do.
>From an implementation perspective, we try to follow the intent of the
user, otherwise there is a risk that we might livelock them (they try to
change the MTU on an already-bridged interface, but we just keep
changing it back in an attempt to keep the MTU normalized). So the MTU
that the bridge is normalized to is either:
- The most recently changed one:
ip link set dev swp0 master br0
ip link set dev swp1 master br0
ip link set dev swp0 mtu 1400
This sequence will make swp1 inherit MTU 1400 from swp0.
- The one of the most recently added interface to the bridge:
ip link set dev swp0 master br0
ip link set dev swp1 mtu 1400
ip link set dev swp1 master br0
The above sequence will make swp0 inherit MTU 1400 as well.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful be able to configure port policers on a switch to accept
frames of various sizes:
- Increase the MTU for better throughput from the default of 1500 if it
is known that there is no 10/100 Mbps device in the network.
- Decrease the MTU to limit the latency of high-priority frames under
congestion, or work around various network segments that add extra
headers to packets which can't be fragmented.
For DSA slave ports, this is mostly a pass-through callback, called
through the regular ndo ops and at probe time (to ensure consistency
across all supported switches).
The CPU port is called with an MTU equal to the largest configured MTU
of the slave ports. The assumption is that the user might want to
sustain a bidirectional conversation with a partner over any switch
port.
The DSA master is configured the same as the CPU port, plus the tagger
overhead. Since the MTU is by definition L2 payload (sans Ethernet
header), it is up to each individual driver to figure out if it needs to
do anything special for its frame tags on the CPU port (it shouldn't
except in special cases). So the MTU does not contain the tagger
overhead on the CPU port.
However the MTU of the DSA master, minus the tagger overhead, is used as
a proxy for the MTU of the CPU port, which does not have a net device.
This is to avoid uselessly calling the .change_mtu function on the CPU
port when nothing should change.
So it is safe to assume that the DSA master and the CPU port MTUs are
apart by exactly the tagger's overhead in bytes.
Some changes were made around dsa_master_set_mtu(), function which was
now removed, for 2 reasons:
- dev_set_mtu() already calls dev_validate_mtu(), so it's redundant to
do the same thing in DSA
- __dev_set_mtu() returns 0 if ops->ndo_change_mtu is an absent method
That is to say, there's no need for this function in DSA, we can safely
call dev_set_mtu() directly, take the rtnl lock when necessary, and just
propagate whatever errors get reported (since the user probably wants to
be informed).
Some inspiration (mainly in the MTU DSA notifier) was taken from a
vaguely similar patch from Murali and Florian, who are credited as
co-developers down below.
Co-developed-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Co-developed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change DMA descriptor length to handle jumbo frames beyond 8192 bytes.
Also update jumbo frame max size to include FCS, the DMA packet length
received includes FCS.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM7XX PHY family requires special configuration to pass jumbo
frames. Do that during initial PHY setup.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f325937735 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJefdsZAAoJEG4XJFUm622blekH/2fIoUtl8Kdih38hNjz63PLD
x+LCPjZdRjrmFGTSxnS1rZiIM7v2yXyLGiyq+yr2ltzkpTi8xWOkKL6US8RCew9R
otRtZyLrhgMLG2ExDna1fI5ZJAtLnxV31TCy6yrSUDZ8t4VxMNIB4si3WRzKvAfU
c+cQcsnWr+pCDnbxh53BcYIyiEqKlttw/fGuIKchKuYMQy7DV6nxMdTaAym5Szzi
Nlb8fhXWFaPrPQ6NtHb5WWm4Er3wtMzN/AG8aFVxjrik07vTxQKWamdT9CeK2tDT
iDbx2HaNCWFMulXeZMrc9+inoAzj3UjbPqH3OTUk9iHbVA0unc3CdEBFD9h928Q=
=D/FA
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
====================
Kalle gave me directions on how to resolve the iwlwifi conflict
as follows:
====================
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: updates 2020-03-27
please apply the following patch series for qeth to netdev's net-next
tree.
Spring clean edition:
- remove one sysfs attribute that was never put in use,
- make support for OSN and OSX devices optional, and
- probe for removal of the obsolete OSN support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
OSN devices currently spend an awful long time in qeth_l2_set_online()
until various unsupported HW cmds time out. This has been broken for
over two years, ever since
commit d22ffb5a71 ("s390/qeth: fix IPA command submission race")
triggered a FW bug in cmd processing.
Prior to commit 782e4a7921 ("s390/qeth: don't poll for cmd IO completion"),
this wait for timeout would have even been spent busy-polling.
The offending patch was picked up by stable and all relevant distros,
and yet noone noticed.
OSN setups only ever worked in combination with an out-of-tree blob, and
the last machine that even offered HW with OSN support was released back
in 2015.
Rather than attempting to work-around this FW issue for no actual gain,
add a deprecation warning so anyone who still wants to maintain this
part of the code can speak up. Else rip it all out in 2021.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last machine generation that supports OSN is z13, and OSX is only
supported up to z14. Allow users and distros to decide whether they
still need support for these device types.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since commit 4a71df5004 ("qeth: new qeth device driver") introduced
this attribute, it can be read & written but has no actual effect.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam says:
====================
bnxt_en: Updates to devlink info_get cb
This series adds support for a generic macro to devlink info_get cb.
Adds support for fw.mgmt.api and board.id info to bnxt_en driver info_get
cb. Also, updates the devlink-info.rst and bnxt.rst documentation
accordingly.
This series adds a patch to fix few macro names that maps to bnxt_en
firmware versions.
v1->v2: Remove ECN dev param, base_mh_addr and serial number info support
in this series.
Rename drv.spec macro to fw.api.
---
v2->v3: Remove hw.addr info as it is per netdev but not per device info.
---
v3->v4: Rename "fw.api" to "fw.mgmt.api".
Also, add a patch that modifies few macro names in info_get command,
to match the devlink documentation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix macro names to report fw.mgmt and fw.ncsi versions to match the
devlink documentation.
Example display after fixes:
$ devlink dev info pci/0000:af:00.0
pci/0000:af:00.0:
driver bnxt_en
serial_number B0-26-28-FF-FE-25-84-20
versions:
fixed:
board.id BCM957454A4540
asic.id C454
asic.rev 1
running:
fw 216.1.154.0
fw.psid 0.0.0
fw.mgmt 216.1.146.0
fw.mgmt.api 1.10.1
fw.ncsi 864.0.44.0
fw.roce 216.1.16.0
Fixes: 9599e036b1 ("bnxt_en: Add support for devlink info command")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add part number info from the vital product data to info_get command
via devlink tool. Update bnxt.rst documentation as well.
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the part number and serial number information from VPD in
the bnxt structure. Follow up patch will add the support to display
the information via devlink command.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new macro for serial number keyword.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display the minimum version of firmware interface spec supported
between driver and firmware. Also update bnxt.rst documentation file.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition and documentation for the new generic info
"fw.mgmt.api". This macro specifies the version of the software
interfaces between driver and firmware.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Various static checkers fixes
Jakub told me he gets some warnings with W=1, so I decided to check with
sparse, smatch and coccinelle as well. This patch set fixes all the
issues found. None are actual bugs / regressions and therefore not
targeted at net.
Patches #1-#2 add missing kernel-doc comments.
Patch #3 removes dead code.
Patch #4 reworks the ACL code to avoid defining a static variable in a
header file.
Patch #5 removes unnecessary conversion to bool that coccinelle warns
about.
Patch #6 avoids false-positive uninitialized symbol errors emitted by
smatch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress the following smatch errors. None of these are actually
possible with current code paths.
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1220
mlxsw_sp_ipip_entry_find_decap() error: uninitialized symbol 'saddrp'.
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1220
mlxsw_sp_ipip_entry_find_decap() error: uninitialized symbol
'saddr_len'.
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1221
mlxsw_sp_ipip_entry_find_decap() error: uninitialized symbol
'saddr_prefix_len'.
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:1390
mlxsw_sp_netdevice_ipip_ol_reg_event() error: uninitialized symbol
'ipipt'.
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3255
mlxsw_sp_nexthop_group_update() error: uninitialized symbol 'err'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress following warning from coccinelle:
drivers/net/ethernet/mellanox/mlxsw//switchx2.c:183:63-68: WARNING:
conversion to bool not needed here
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The static array 'mlxsw_afk_element_infos' in 'core_acl_flex_keys.h' is
copied to each file that includes the header, but not all use it. This
results in the following warnings when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//core_acl_flex_keys.h:76:44:
warning: ‘mlxsw_afk_element_infos’ defined but not used
[-Wunused-const-variable=]
One way to suppress the warning is to mark the array with
'__maybe_unused', but another option is to remove it from the header
file entirely.
Change 'struct mlxsw_afk_element_inst' to store the key to the array
('element') instead of the array value keyed by 'element'. Adjust the
different users accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In merge commit 50853808ff ("Merge branch
'mlxsw-Prepare-for-VLAN-aware-bridge-w-VxLAN'") I flipped mlxsw to use
emulated 802.1Q FIDs and correspondingly emulated VLAN RIFs. This means
that the non-emulated variants are no longer used. Remove them and
suppress the following warnings when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:7572:38: warning:
‘mlxsw_sp_rif_vlan_ops’ defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/mellanox/mlxsw//spectrum_fid.c:584:41: warning:
‘mlxsw_sp_fid_8021q_family’ defined but not used
[-Wunused-const-variable=]
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress following warnings when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1552: warning:
Function parameter or member 'mlxsw_sp' not described in
'__mlxsw_sp_ipip_entry_update_tunnel'
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1552: warning:
Function parameter or member 'ipip_entry' not described in
'__mlxsw_sp_ipip_entry_update_tunnel'
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1552: warning:
Function parameter or member 'extack' not described in
'__mlxsw_sp_ipip_entry_update_tunnel'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress following warning when compiling with W=1:
drivers/net/ethernet/mellanox/mlxsw//i2c.c:78: warning: Function
parameter or member 'cmd' not described in 'mlxsw_i2c'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-03-27
1) Handle NETDEV_UNREGISTER for xfrm device to handle asynchronous
unregister events cleanly. From Raed Salem.
2) Fix vti6 tunnel inter address family TX through bpf_redirect().
From Nicolas Dichtel.
3) Fix lenght check in verify_sec_ctx_len() to avoid a
slab-out-of-bounds. From Xin Long.
4) Add a missing verify_sec_ctx_len check in xfrm_add_acquire
to avoid a possible out-of-bounds to access. From Xin Long.
5) Use built-in RCU list checking of hlist_for_each_entry_rcu
to silence false lockdep warning in __xfrm6_tunnel_spi_lookup
when CONFIG_PROVE_RCU_LIST is enabled. From Madhuparna Bhowmik.
6) Fix a panic on esp offload when crypto is done asynchronously.
From Xin Long.
7) Fix a skb memory leak in an error path of vti6_rcv.
From Torsten Hilbrich.
8) Fix a race that can lead to a doulbe free in xfrm_policy_timer.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
