It turned out that the recent Intel HD-audio controller chips show a
significant stall during the system PM resume intermittently. It
doesn't happen so often and usually it may read back successfully
after one or more seconds, but in some rare worst cases the driver
went into fallback mode.
After trial-and-error, we found out that the communication stall seems
covered by issuing the sync after each verb write, as already done for
AMD and other chipsets. So this patch enables the write-sync flag for
the recent Intel chips, Skylake and onward, as a workaround.
Also, since Broxton and co have the very same driver flags as Skylake,
refer to the Skylake driver flags instead of defining the same
contents again for simplification.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201901
Reported-and-tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the DAI format setup fails, there is no valid communication format
between CPU and CODEC, so fail card instantiation, rather than continue
with a card that will most likely not function properly.
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.20.1907241132350.6338@lnxricardw1.se.axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
put_device will call ac97_codec_release to free
ac97_codec_device and other resources, so remove the kfree
and other redundant code.
Fixes: 74426fbff6 ("ALSA: ac97: add an ac97 bus")
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Downgrade "nothing to do in IRQ thread" message from error to a debug
message in the IPC interrupt handler thread.
The spurious wake-up can happen if a HDA stream interrupt is
raised while the IPC interrupt thread is running. IPC functionality
is not impacted by this condition, so debug is a more appropriate
trace level.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190722141402.7194-21-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
apq8016_sbc_parse_of() sets up multiple DAI links, depending on the
number of nodes in the device tree. However, at the moment
CPU and platform components are only allocated for the first link.
This causes an oops when more than one link is defined:
Internal error: Oops: 96000044 [#1] SMP
CPU: 0 PID: 1015 Comm: kworker/0:2 Not tainted 5.3.0-rc1 #4
Call trace:
apq8016_sbc_platform_probe+0x1a8/0x3f0
platform_drv_probe+0x50/0xa0
...
Move the allocation inside the loop to ensure that each link is
properly initialized.
Fixes: 98b232ca9e ("ASoC: qcom: apq8016_sbc: use modern dai_link style")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20190722130352.95874-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Draining makes little sense in the situation of hardware overrun, as the
hardware will have consumed all its available samples. Additionally,
draining whilst the stream is paused would presumably get stuck as no
data is being consumed on the DSP side.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Partial drain and next track are intended for gapless playback and
don't really have an obvious interpretation for a capture stream, so
makes sense to not allow those operations on capture streams.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, whilst in SNDRV_PCM_STATE_OPEN it is possible to call
snd_compr_stop, snd_compr_drain and snd_compr_partial_drain, which
allow a transition to SNDRV_PCM_STATE_SETUP. The stream should
only be able to move to the setup state once it has received a
SNDRV_COMPRESS_SET_PARAMS ioctl. Fix this issue by not allowing
those ioctls whilst in the open state.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A previous fix to the stop handling on compressed capture streams causes
some knock on issues. The previous fix updated snd_compr_drain_notify to
set the state back to PREPARED for capture streams. This causes some
issues however as the handling for snd_compr_poll differs between the
two states and some user-space applications were relying on the poll
failing after the stream had been stopped.
To correct this regression whilst still fixing the original problem the
patch was addressing, update the capture handling to skip the PREPARED
state rather than skipping the SETUP state as it has done until now.
Fixes: 4f2ab5e1d1 ("ALSA: compress: Fix stop handling on compressed capture streams")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In snd_soc_dapm_new_control_unlocked(), a kernel buffer is allocated in
dapm_cnew_widget() to hold the new dapm widget. Then, different actions are
taken according to the id of the widget, i.e., 'w->id'. If any failure
occurs during this process, snd_soc_dapm_new_control_unlocked() should be
terminated by going to the 'request_failed' label. However, the allocated
kernel buffer is not freed on this code path, leading to a memory leak bug.
To fix the above issue, free the buffer before returning from
snd_soc_dapm_new_control_unlocked() through the 'request_failed' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Link: https://lore.kernel.org/r/1563803864-2809-1-git-send-email-wang6495@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
The TS3A227E says that the headset keypress detection needs the MICBIAS
power in order to report the key events to ensure proper operation
The headset keypress detection needs the MICBIAS power in order to report
the key events all the time as long as MIC is present. So MICBIAS pin
is forced on when a MICROPHONE is detected.
On Veyron Minnie I observed that if the MICBIAS power is not present and
the key press detection is activated (just because it is enabled when you
insert a headset), it randomly reports a keypress on insert.
E.g. (KEY_PLAYPAUSE)
Event: (SW_HEADPHONE_INSERT), value 1
Event: (SW_MICROPHONE_INSERT), value 1
Event: -------------- SYN_REPORT ------------
Event: (KEY_PLAYPAUSE), value 1
Userspace thinks that KEY_PLAYPAUSE is pressed and produces the annoying
effect that the media player starts a play/pause loop.
Note that, although most of the time the key reported is the one
associated with BTN_0, not always this is true. On my tests I also saw
different keys reported
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20190719173929.24065-1-enric.balletbo@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When sample rate of TX is different with sample rate of RX in
async mode, the MFreq selection will be wrong.
For example, sysclk = 24.576MHz, TX rate = 96000Hz, RX rate = 48000Hz.
Then ratio of TX = 256, ratio of RX = 512, For MFreq is shared by TX
and RX instance, the correct value of MFreq is 2 for both TX and RX.
But original method will cause MFreq = 0 for TX, MFreq = 2 for RX.
If TX is started after RX, RX will be impacted, RX work abnormal with
MFreq = 0.
This patch is to select proper MFreq value according to TX rate and
RX rate.
Fixes: 0c516b4ff8 ("ASoC: cs42xx8: Add codec driver support for CS42448/CS42888")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/20190716094547.46787-1-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DPCM uses snd_soc_dapm_dai_get_connected_widgets to build a
list of the widgets connected to a specific front end DAI so it
can search through this list for available back end DAIs. The
custom_stop_condition was added to is_connected_ep to facilitate this
list not containing more widgets than is necessary. Doing so both
speeds up the DPCM handling as less widgets need to be searched and
avoids issues with CODEC to CODEC links as these would be confused
with back end DAIs if they appeared in the list of available widgets.
custom_stop_condition was implemented by aborting the graph walk
when the condition is triggered, however there is an issue with this
approach. Whilst walking the graph is_connected_ep should update the
endpoints cache on each widget, if the walk is aborted the number
of attached end points is unknown for that sub-graph. When the stop
condition triggered, the original patch ignored the triggering widget
and returned zero connected end points; a later patch updated this
to set the triggering widget's cache to 1 and return that. Both of
these approaches result in inaccurate values being stored in various
end point caches as the values propagate back through the graph,
which can result in later issues with widgets powering/not powering
unexpectedly.
As the original goal was to reduce the size of the widget list passed
to the DPCM code, the simplest solution is to limit the functionality
of the custom_stop_condition to the widget list. This means the rest
of the graph will still be processed resulting in correct end point
caches, but only widgets up to the stop condition will be added to the
returned widget list.
Fixes: 6742064aef ("ASoC: dapm: support user-defined stop condition in dai_get_connected_widgets")
Fixes: 5fdd022c20 ("ASoC: dpcm: play nice with CODEC<->CODEC links")
Fixes: 09464974ea ("ASoC: dapm: Fix to return correct path list in is_connected_ep.")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20190718084333.15598-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent rewrite of PCM link lock management introduced the refcount
in snd_pcm_group object, managed by the kernel refcount_t API. This
caused unexpected kernel warnings when the kernel is built with
CONFIG_REFCOUNT_FULL=y. As the warning line indicates, the problem is
obviously that we start with refcount=0 and do refcount_inc() for
adding each PCM link, while refcount_t API doesn't like refcount_inc()
performed on zero.
For adapting the proper refcount_t usage, this patch changes the logic
slightly:
- The initial refcount is 1, assuming the single list entry
- The refcount is incremented / decremented at each PCM link addition
and deletion
- ... which allows us concentrating only on the refcount as a release
condition
Fixes: f57f3df03a ("ALSA: pcm: More fine-grained PCM link locking")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204221
Reported-and-tested-by: Duncan Overbruck <kernel@duncano.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of small fixes.
- The optimization of PM resume with HD-audio HDMI codecs, which
eventually work around weird issues
- A correction of Intel Icelake HDMI audio code
- Quirks for Dell machines with Realtek HD-audio codecs
- The fix for too long sequencer write stall that was spotted by
syzkaller
- A few trivial cleanups reported by coccinelle
-----BEGIN PGP SIGNATURE-----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=p0qg
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes.
- The optimization of PM resume with HD-audio HDMI codecs, which
eventually work around weird issues
- A correction of Intel Icelake HDMI audio code
- Quirks for Dell machines with Realtek HD-audio codecs
- The fix for too long sequencer write stall that was spotted by
syzkaller
- A few trivial cleanups reported by coccinelle"
* tag 'sound-fix-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Don't resume forcibly i915 HDMI/DP codec
ALSA: hda/hdmi - Fix i915 reverse port/pin mapping
ALSA: hda/hdmi - Remove duplicated define
ALSA: seq: Break too long mutex context in the write loop
ALSA: hda/realtek: apply ALC891 headset fixup to one Dell machine
ALSA: rme9652: Unneeded variable: "result".
ALSA: emu10k1: Remove unneeded variable "change"
ALSA: au88x0: Remove unneeded variable: "changed"
ALSA: hda/realtek - Fixed Headphone Mic can't record on Dell platform
ALSA: ps3: Remove Unneeded variable: "ret"
ALSA: lx6464es: Remove unneeded variable err
Commit 7b9584fa1c ("staging: line6: Move altsetting to properties")
set a wrong altsetting for LINE6_PODHD500_1 during refactoring.
Set the correct altsetting number to fix the issue.
BugLink: https://bugs.launchpad.net/bugs/1790595
Fixes: 7b9584fa1c ("staging: line6: Move altsetting to properties")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The codecs without jack detection also don't have to be resumed
forcibly because, obviously, they have no jack. Skip the forced
resume in such a case as optimization as well.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We apply the codec resume forcibly at system resume callback for
updating and syncing the jack detection state that may have changed
during sleeping. This is, however, superfluous for the codec like
Intel HDMI/DP, where the jack detection is managed via the audio
component notification; i.e. the jack state change shall be reported
sooner or later from the graphics side at mode change.
This patch changes the codec resume callback to avoid the forcible
resume conditionally with a new flag, codec->relaxed_resume, for
reducing the resume time. The flag is set in the codec probe.
Although this doesn't fix the entire bug mentioned in the bugzilla
entry below, it's still a good optimization and some improvements are
seen.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201901
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The cpu_dai variable is still being used after the of_node_put() call,
which may result in double-free:
of_node_put(cpu_dai); ---> released here
ret = devm_snd_soc_register_card(dev, card);
if (ret < 0) {
...
goto err_put_clk_i2s; --> jump to err_put_clk_i2s
...
err_put_clk_i2s:
clk_put(priv->clk_i2s_bus);
err_put_sclk:
clk_put(priv->sclk_i2s);
err_put_cpu_dai:
of_node_put(cpu_dai); --> double-free here
Fixes: d832d2b246 ("ASoC: samsung: odroid: Fix of_node refcount unbalance")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1562989575-33785-3-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec variable is still being used after the of_node_put() call,
which may result in use-after-free.
Fixes: bc3cf17b57 ("ASoC: samsung: odroid: Add support for secondary CPU DAI")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1562989575-33785-2-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent fix for Icelake HDMI codec introduced the mapping from pin
NID to the i915 gfx port number. However, it forgot the reverse
mapping from the port number to the pin NID that is used in the ELD
notifier callback. As a result, it's processed to a wrong widget and
gives a warning like
snd_hda_codec_hdmi hdaudioC0D2: HDMI: pin nid 5 not registered
This patch corrects it with a proper reverse mapping function.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204133
Fixes: b0d8bc50b9 ("ALSA: hda: hdmi - add Icelake support")
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The fix for the racy writes and ioctls to sequencer widened the
application of client->ioctl_mutex to the whole write loop. Although
it does unlock/relock for the lengthy operation like the event dup,
the loop keeps the ioctl_mutex for the whole time in other
situations. This may take quite long time if the user-space would
give a huge buffer, and this is a likely cause of some weird behavior
spotted by syzcaller fuzzer.
This patch puts a simple workaround, just adding a mutex break in the
loop when a large number of events have been processed. This
shouldn't hit any performance drop because the threshold is set high
enough for usual operations.
Fixes: 7bd8009156 ("ALSA: seq: More protection for concurrent write and ioctl races")
Reported-by: syzbot+97aae04ce27e39cbfca9@syzkaller.appspotmail.com
Reported-by: syzbot+4c595632b98bb8ffcc66@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without this patch, the headset-mic and headphone-mic don't work.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It assigned to wrong model. So, The headphone Mic can't work.
Fixes: 3f640970a4 ("ALSA: hda - Fix headset mic detection problem for several Dell laptops")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
* CrOS EC:
- Add new CrOS ISHTP transport protocol
- Add proper documentation for debugfs entries and expose resume and uptime files
- Select LPC transport protocol variant at runtime.
- Add lid angle sensor driver
- Fix oops on suspend/resume for lightbar driver
- Set CrOS SPI transport protol in realtime
* Wilco EC:
- Add telemetry char device interface
- Add support for event handling
- Add new sysfs attributes
* Misc:
- Contains ib-mfd-cros-v5.3 immutable branch from mfd, with cros_ec_commands.h
header freshly synced with Chrome OS's EC project.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXSbP3AAKCRBzbaomhzOw
wjoNAP4lrY3UboMaQklHLOCxPTFXwIHjImXxJUCrezJj4eBRcwEAz+adSNKieVEY
xNf/yetCkjVnQNMVjGaBJRUp3F+2LwQ=
=/Xj3
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung
"CrOS EC:
- Add new CrOS ISHTP transport protocol
- Add proper documentation for debugfs entries and expose resume and
uptime files
- Select LPC transport protocol variant at runtime.
- Add lid angle sensor driver
- Fix oops on suspend/resume for lightbar driver
- Set CrOS SPI transport protol in realtime
Wilco EC:
- Add telemetry char device interface
- Add support for event handling
- Add new sysfs attributes
Misc:
- Contains ib-mfd-cros-v5.3 immutable branch from mfd, with
cros_ec_commands.h header freshly synced with Chrome OS's EC
project"
* tag 'tag-chrome-platform-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: (54 commits)
mfd / platform: cros_ec_debugfs: Expose resume result via debugfs
platform/chrome: lightbar: Get drvdata from parent in suspend/resume
iio: cros_ec: Add lid angle driver
platform/chrome: wilco_ec: Add circular buffer as event queue
platform/chrome: cros_ec_lpc_mec: Fix kernel-doc comment first line
platform/chrome: cros_ec_lpc: Choose Microchip EC at runtime
platform/chrome: cros_ec_lpc: Merge cros_ec_lpc and cros_ec_lpc_reg
Input: cros_ec_keyb: mask out extra flags in event_type
platform/chrome: wilco_ec: Fix unreleased lock in event_read()
platform/chrome: cros_ec_debugfs: cros_ec_uptime_fops can be static
platform/chrome: cros_ec_debugfs: Add debugfs ABI documentation
platform/chrome: cros_ec_debugfs: Fix kernel-doc comment first line
platform/chrome: cros_ec_debugfs: Add debugfs entry to retrieve EC uptime
mfd: cros_ec: Update I2S API
mfd: cros_ec: Add Management API entry points
mfd: cros_ec: Add SKU ID and Secure storage API
mfd: cros_ec: Add API for rwsig
mfd: cros_ec: Add API for Fingerprint support
mfd: cros_ec: Add API for Touchpad support
mfd: cros_ec: Add API for EC-EC communication
...
commit c152f8491a ("ASoC: audio-graph-card: fix an use-after-free in
graph_get_dai_id()") fixups use-after-free issue,
but, it need to use "const" for reg. This patch adds it.
We will have below without this patch
LINUX/sound/soc/generic/audio-graph-card.c: In function 'graph_get_dai_id':
LINUX/sound/soc/generic/audio-graph-card.c:87:7: warning: assignment discards\
'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
reg = of_get_property(node, "reg", NULL);
Fixes: c152f8491a ("ASoC: audio-graph-card: fix an use-after-free in graph_get_dai_id()")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Wen Yang <wen.yang99@zte.com.cn>
Link: https://lore.kernel.org/r/87sgrd43ja.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two issues to fix:
- DC offset calibration data will be reset after stopping playback.
- DC offset calibration data should be applied in the initial setting.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20190711082214.8142-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After calling of_node_put() on the node variable, it is still being
used, which may result in use-after-free.
Fix this issue by calling of_node_put() after the last usage.
Fixes: a0c426fe14 ("ASoC: simple-card-utils: check "reg" property on asoc_simple_card_get_dai_id()")
Link: https://lore.kernel.org/r/1562743509-30496-5-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After calling of_node_put() on the ports, port, and node variables,
they are still being used, which may result in use-after-free.
Fix this issue by calling of_node_put() after the last usage.
Fixes: dd98fbc558 ("ASoC: audio-graph-card: cleanup DAI link loop method - step1")
Link: https://lore.kernel.org/r/1562743509-30496-4-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec variable is still being used after the of_node_put() call,
which may result in use-after-free.
Fixes: d947cdfd4b ("ASoC: simple-card: cleanup DAI link loop method - step1")
Link: https://lore.kernel.org/r/1562743509-30496-3-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The node variable is still being used after the of_node_put() call,
which may result in use-after-free.
Fixes: cfc652a733 ("ASoC: simple-card: tidyup prefix for snd_soc_codec_conf")
Link: https://lore.kernel.org/r/1562743509-30496-2-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 3461473998 ("ASoC: soc-core: support dai_link with
platforms_num != 1") supports multi Platform, and
commit 9f3eb91753 ("ASoC: simple-card-utils: consider CPU-Platform
possibility") removed no Platform from simple-card.
Multi Platform is now checking both Platform name/of_node are NULL case.
But in normal case, DPCM be doesn't have Platform.
asoc_simple_canonicalize_platform() try to use CPU of_node
to Platform (This is needed for DMAEngine platform case),
but it still might be NULL at DPCM be.
This patch try to use no Platform after that if Platform of_node
is still NULL. It can't probe without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87muhmgw2o.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
max98357a_daiops_trigger() is possible to be called in atomic context if
the .nonatomic flag is equal to 0 in the DAI links.
When cancel_delayed_work_sync() in max98357a_daiops_trigger() is called
in atomic context, kernel emits the following message: "BUG: sleeping
function called from invalid context".
According to the DT binding document, value less than or equal to 5ms of
sdmod-delay should be sufficient to avoid the pop noise. Use mdelay
(i.e. busy loop) for such low delay should be acceptable.
Fixes: cec5b01f8f ("ASoC: max98357a: avoid speaker pop when playback
startup")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20190708141901.68797-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
It's better to use int type for loop index. For consistency, the name
of local variable for the number of data block should be plural.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a result of former commits, post operation to data block count for
cases without CIP_DBC_IS_END_EVENT can be done just with
data_block_counter member of amdtp_stream structure.
This commit adds code refactoring to obsolete local variable for
data block counter.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a parser for CIP header returns -EAGAIN, no extra care is needed
to probe tracepoints event.
This commit adds code refactoring for the error path.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For IT context, tracepoints event is probed after calculating next data
block counter. This brings difference of data block counter between
the probed event and actual isochronous packet.
This commit fixes it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For IR context, ALSA IEC 61883-1/6 engine uses initial value of data
block counter as UINT_MAX, to detect first isochronous packet in the
middle of packet streaming.
At present, when CIP_DBC_IS_END_EVENT is not used (i.e. for drivers except
for ALSA fireworks driver), the initial value is used as is for
tracepoints event. However, the engine can detect the value of dbc field
in the payload of first isochronous packet and the value should be assigned
to the event.
This commit fixes the bug.
Fixes: 76864868db ("ALSA: firewire-lib: cache next data_block_counter after probing tracepoints event for IR context")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For IR context, ALSA IEC 61883-1/6 engine uses initial value of data
block counter as UINT_MAX, to detect first isochronous packet in the
middle of packet streaming.
At present, when CIP_NO_HEADER is used (i.e. for ALSA fireface driver),
the initial value is used for tracepoints event. 0x00 should be
for the event when the initial value is UINT_MAX because isochronous
packets with CIP_NO_HEADER option has no field for data block count.
This commit fixes the bug.
Fixes: 76864868db ("ALSA: firewire-lib: cache next data_block_counter after probing tracepoints event for IR context")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although CIP header is handled as context header, the length of isochronous
packet includes two quadlets for its payload. In tracepoints event the
value of payload_quadlets should includes the two quadlets. But at present
it doesn't.
This commit fixes the bug.
Fixes: b18f0cfaf1 ("ALSA: firewire-lib: use 8 byte packet header for IT context to separate CIP header from CIP payload")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl0jGwUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LD4B/9AkutfS+vznOrk0V0wFb2SUfjwE4Pr
+z/kAehohAOl/7pg9Dun/lmZYBWMyOM2aYmK81ahEo2DfO+uzwkwjCaXFjGVGwEK
j7XpWkrIjKnou/z1FeALgVvt+crzdy5iNWC04AbKaP2WHCcI7zvPQIsBta/V0OJt
lg+j0J7pagnTMcgV1+qJdaASmofy/hpoZ79Gv0PIfGC8hpJ/3mBgcNPCLQrJtD4R
v+tzvCZNrZVqCanwLf3vouEm1bpWYOpI+Wdmu4u6rY7MhmCj72EJ2zyfdm/qtaxF
e7whgCyOQFkWe7NgDn0G08aAT6LsaxOtPNr7H8tL8S8sw8425fqeOouV
=n/HQ
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.3
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Line6 Helix and HX stomp devices don't support retrieving
the number of clock sample rate.
Add a quirk to set it to 48Khz by default.
[ fixed wrong variable initialization changes by tiwai ]
Signed-off-by: Nicola Lunghi <nick83ola@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, several types of sampling data can be multiplexed into
payload of common isochronous packet (CIP). For typical audio and music
units, PCM samples and MIDI messages are multiplexed into one packet
streaming.
ALSA firewire-motu driver allows applications of rawmidi interface to
start packet streaming for transmission of MIDI messages. However at
error path, the reference count of stream functionality is not operated
correctly. This can brings a bug that packet streaming is not stopped
when all referrers release the count.
This commit fixes the bug.
Fixes: 8edc56ec8f ("ALSA: firewire-motu: reserve/release isochronous resources in pcm.hw_params/hw_free callbacks")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, several types of sampling data can be multiplexed into
payload of common isochronous packet (CIP). For typical audio and music
units, PCM samples and MIDI messages are multiplexed into one packet
streaming.
ALSA firewire-digi00x driver allows applications of rawmidi interface to
start packet streaming for transmission of MIDI messages. However at
error path, the reference count of stream functionality is not operated
correctly. This can brings a bug that packet streaming is not stopped
when all referrers release the count.
This commit fixes the bug.
Fixes: ae8ffbb265 ("ALSA: firewire-digi00x: reserve/release isochronous resources in pcm.hw_params/hw_free callbacks")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, several types of sampling data can be multiplexed into
payload of common isochronous packet (CIP). For typical audio and music
units, PCM samples and MIDI messages are multiplexed into one packet
streaming.
ALSA dice driver allows applications of rawmidi interface to start
packet streaming for transmission of MIDI messages. However at error
path, the reference count of stream functionality is not operated
correctly. This can brings a bug that packet streaming is not stopped
when all referrers release the count.
This commit fixes the bug.
Fixes: 3cd2c2d780 ("ALSA: dice: reserve/release isochronous resources in pcm.hw_params/hw_free callbacks")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, several types of sampling data can be multiplexed into
payload of common isochronous packet (CIP). For typical audio and music
units, PCM samples and MIDI messages are multiplexed into one packet
streaming.
ALSA oxfw driver allows applications of rawmidi interface to start
packet streaming for transmission of MIDI messages. However at error
path, the reference count of stream functionality is not operated
correctly. This can brings a bug that packet streaming is not stopped
when all referrers release the count.
This commit fixes the bug.
Fixes: 4f380d0070 ("ALSA: oxfw: configure packet format in pcm.hw_params callback")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, several types of sampling data can be multiplexed into
payload of common isochronous packet (CIP). For typical audio and music
units, PCM samples and MIDI messages are multiplexed into one packet
streaming.
ALSA fireworks driver allows applications of rawmidi interface to start
packet streaming for transmission of MIDI messages. However at error
path, the reference count of stream functionality is not operated
correctly. This can brings a bug that packet streaming is not stopped
when all referrers release the count.
This commit fixes the bug.
Fixes: 3d7250667e ("ALSA: fireworks: configure sampling transfer frequency in pcm.hw_params callback")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, several types of sampling data can be multiplexed into
payload of common isochronous packet (CIP). For typical audio and music
units, PCM samples and MIDI messages are multiplexed into one packet
streaming.
ALSA bebob driver allows applications of rawmidi interface to start
packet streaming for transmission of MIDI messages. However at error
path, the reference count of stream functionality is not operated
correctly. This can brings a bug that packet streaming is not stopped
when all referrers release the count.
This commit fixes the bug.
Fixes: ac2888b958 ("ALSA: bebob: configure sampling transfer frequency in pcm.hw_params callback")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement runtime idle for CNL/APL devices using similar runtime
PM idle logic as the Intel AZX HDA driver. If any HDA codecs are
powered when runtime suspend request comes, return -EBUSY. By doing
this, strict ordering is enforced between HDA codec and the HDA
controller.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20190702132428.13129-4-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ability to implement a SOF device level runtime idle callback.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20190702132428.13129-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Report codec power status to the HDA codec bus from runtime pm
suspend and resume callbacks. This is required to implement
runtime idle logic that relies on 'codec_powered' field of hdac_bus
to be maintained for all codecs.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20190702132428.13129-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
'string' is malloced in sof_dfsentry_write() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: 091c12e1f5 ("ASoC: SOF: debug: add new debugfs entries for IPC flood test")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20190705081637.157169-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds the necessary registers and audio routes to play audio using
the Earpiece, that's supported on the A64.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20190703184814.27191-1-luca@z3ntu.xyz
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable idx is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190705075303.14692-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable val is being assigned with a value that is never
read and it is being updated later with a new value. The
assignment is redundant and can be removed. Also remove a
goto statement and a label and replace with a break statement.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Along with the recent fix for the races of snd_hdac_refresh_widgets()
it turned out that the instantiation of widgets sysfs at
snd_hdac_sysfs_reinit() could cause a race. The race itself was
already covered later by extending the mutex protection range, the
commit 98482377dc ("ALSA: hda: Fix widget_mutex incomplete
protection"), but this also indicated that the call of *_reinit() is
basically superfluous, as the widgets shall be created sooner or later
from snd_hdac_device_register().
This patch removes the redundant call of snd_hdac_sysfs_reinit() at
first. By this removal, the sysfs argument itself in
snd_hdac_refresh_widgets() becomes superfluous, too, because the only
case sysfs=false is always with codec->widgets=NULL. So, we drop this
redundant argument as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Extension Unit (XU) is used to have a compatible layout with
Processing Unit (PU) on UAC1, and the usb-audio driver code assumed it
for parsing the descriptors. Meanwhile, on UAC2, XU became slightly
incompatible with PU; namely, XU has a one-byte bmControls bitmap
while PU has two bytes bmControls bitmap. This incompatibility
results in the read of a wrong address for the last iExtension field,
which ended up with an incorrect string for the mixer element name, as
recently reported for Focusrite Scarlett 18i20 device.
This patch corrects this misalignment by introducing a couple of new
macros and calling them depending on the descriptor type.
Fixes: 23caaf19b1 ("ALSA: usb-mixer: Add support for Audio Class v2.0")
Reported-by: Stefan Sauer <ensonic@hora-obscura.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable 'changed' is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell headset mode platform with ALC236.
It doesn't recording after system resume from S3.
S3 mode was deep. s2idle was not has this issue.
S3 deep will cut of codec power. So, the register will back to default
after resume back.
This patch will solve this issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After calling of_node_put() on the codec_ep and codec_port variables,
they are still being used, which may result in use-after-free.
We fix this issue by calling of_node_put() after the last usage.
Fixes: fce9b90c1a ("ASoC: audio-graph-card: cleanup DAI link loop method - step2")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1562229530-8121-1-git-send-email-wen.yang99@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
It makes it easier for common code to work with snd_soc_dai_set_channel_map()
by distinguishing between operation not being supported and an error.
This is done inline with others snd_soc_dai.* apis.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20190703123002.12427-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the optional reset line handling which is present on the new SoC
families, such as the g12a. Triggering this reset is not critical but
it helps solve a channel shift issue on the g12a.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20190703120749.32341-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
LINE6 drivers allocate the buffers based on the value returned from
usb_maxpacket() calls. The manipulated device may return zero for
this, and this results in the kmalloc() with zero size (and it may
succeed) while the other part of the driver code writes the packet
data with the fixed size -- which eventually overwrites.
This patch adds a simple sanity check for the invalid buffer size for
avoiding that problem.
Reported-by: syzbot+219f00fb49874dcaea17@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Loud speaker pop happens during playback even when in slience
playback. Specify Max98357a amp delay times to make sure
clocks are always earlier than sdmode on.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have devm_xxx version of snd_soc_register_component,
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have devm_xxx version of snd_soc_register_component,
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have devm_xxx version of snd_soc_register_component,
let's use it.
This patch also removes related empty functions
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have devm_xxx version of snd_soc_register_component,
let's use it.
This patch also removes related empty functions
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have devm_xxx version of snd_soc_register_component,
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have devm_xxx version of snd_soc_register_component,
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The widget_mutex was introduced to serialize callers to
hda_widget_sysfs_{re}init. However, its protection of the sysfs widget array
is incomplete. For example, it is acquired around the call to
hda_widget_sysfs_reinit(), which actually creates the new array, but isn't
still acquired when codec->num_nodes and codec->start_nid is updated. So
the lock ensures one thread sets up the new array at a time, but doesn't
ensure which thread's value will end up in codec->num_nodes. If a larger
num_nodes wins but a smaller array was set up, the next call to
refresh_widgets() will touch free memory as it iterates over codec->num_nodes
that aren't there.
The widget_lock really protects both the tree as well as codec->num_nodes,
start_nid, and end_nid, so make sure it's held across that update. It should
also be held during snd_hdac_get_sub_nodes(), so that a very old read from that
function doesn't end up clobbering a later update.
Fixes: ed180abba7 ("ALSA: hda: Fix race between creating and refreshing sysfs entries")
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This back-merge is necessary for adjusting the latest FireWire fix
with the recent refactoring in 5.3 development branch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, 8 MIDI data streams are multiplexed into single
MIDI conformant data channel. The index of stream is calculated by
modulo 8 of the value of data block counter.
In fireworks, the value of data block counter in CIP header has a quirk
with firmware version v5.0.0, v5.7.3 and v5.8.0. This brings ALSA
IEC 61883-1/6 packet streaming engine to miss detection of MIDI
messages.
This commit fixes the miss detection to modify the value of data block
counter for the modulo calculation.
For maintainers, this bug exists since a commit 18f5ed365d ("ALSA:
fireworks/firewire-lib: add support for recent firmware quirk") in Linux
kernel v4.2. There're many changes since the commit. This fix can be
backported to Linux kernel v4.4 or later. I tagged a base commit to the
backport for your convenience.
Besides, my work for Linux kernel v5.3 brings heavy code refactoring and
some structure members are renamed in 'sound/firewire/amdtp-stream.h'.
The content of this patch brings conflict when merging -rc tree with
this patch and the latest tree. I request maintainers to solve the
conflict to replace 'tx_first_dbc' with 'ctx_data.tx.first_dbc'.
Fixes: df075feefb ("ALSA: firewire-lib: complete AM824 data block processing layer")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To save power, the hda hdmi driver in ASoC invokes snd_hdac_ext_bus_link_put
to disable CORB/RIRB buffers DMA if there is no user of bus and invokes
snd_hdac_ext_bus_link_get to set up CORB/RIRB buffers when it is used.
Unsolicited responses is disabled in snd_hdac_bus_stop_cmd_io called by
snd_hdac_ext_bus_link_put , but it is not enabled in snd_hdac_bus_init_cmd_io
called by snd_hdac_ext_bus_link_get. So for put-get sequence, Unsolicited
responses is disabled and headphone can't be detected by hda codecs.
Now unsolicited responses is only enabled in snd_hdac_bus_reset_link
which resets controller. The function is only called for setup of
controller. This patch enables Unsolicited responses after RIRB is
initialized in snd_hdac_bus_init_cmd_io which works together with
snd_hdac_bus_reset_link to set up controller.
Tested legacy hda driver and SOF driver on intel whiskeylake.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit 64ee5067cf ("ASoC: soc-utils: remove dummy Platform") removed
dummy Platform from ALSA SoC, but it is over-kill.
This patch respawn it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 961fb3c206 ("ASoC: rockchip: rk3399_gru_sound: don't select
unnecessary Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 961fb3c206 ("ASoC: rockchip: rk3399_gru_sound: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 0814c64129 ("ASoC: qcom: don't select unnecessary Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 0814c64129 ("ASoC: qcom: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 6f04374457 ("ASoC: simple-card-utils: don't select unnecessary
Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 6f04374457 ("ASoC: simple-card-utils: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
