Driver was using wrong "8-bit" i2c addresses for demods and tuners.
Internal demod i2c address was not set at all. These are needed
to be fixed before proper i2c client binding is used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check return value from call to af9013_wr_regs(), so in case of
error print debug message and return.
Addresses-Coverity-ID: 1227035
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds hardware IDs for all Sony CXD-based Cine-cards and MaxA8 devices, also
adds some other yet missing IDs like the Octopus V3, Octopus OEM and
Octopus Mini, as well as cards with unknown/deleted sub-ids.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Properly detect and attach Ports and Flex modules with the Sony CXD28xxER
series demods. This makes newer Cine cards and most DuoFlex C/C2/T/T2 (or
any combination of these systems) work, PCI IDs need to be added though.
Note: This utilises the CXD2841ER demod driver, which requires the changes
from this patch series to properly work. Without those changes, it won't
function properly (if at all).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some Flex modules (mostly with anyof C/C2/T/T2 demods based on the Sony
CXD28xxER series) are equipped with an interface named XO2 (which
appears to be the Lattice MachXO2). Add functionality to detect such
links and initialise them, so any tuner module with such an interface can
be used.
This also adds dummy detection for any possible connected module, telling
the user it isn't supported at this very moment.
Also adds i2c_io(), i2c_write() and i2c_write_reg(), all required for the
XO2 handling functionality.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a backport of the board control setup from the vendor provided
dddvb driver package, which does additional device initialisation based
on the board_control device info values. Also backports the TS quirk
flags which is used to control setup and usage of the tuner modules
soldered on the bridge cards (e.g. CineCTv7, CineS2 V7, MaxA8 and the
likes).
Functionality originates from ddbridge vendor driver. Permission for
reuse and kernel inclusion was formally granted by Ralph Metzler
<rjkm@metzlerbros.de>.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On DVB-T/T2 at least, SNR might be reported as >2500dB, which not only is
just wrong but also ridiculous, so fix this by improving the conversion
of the register value.
The INTLOG10X100 function/macro and the way the values are converted were
both taken from DD's cxd2843 driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bits 3 and 4 of the TSCONFIG register are important for certain hardware
constellations, in that they need to be zeroed. Add a configuration flag
to toggle this.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds a flag to enable or disable the IFAGCNEG bit in cxd2841er_init_tc().
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't wait for FE_HAS_LOCK in set_frontend_tc() and thus don't hammer the
lock status register with inquiries when CXD2841ER_NO_WAIT_LOCK is set
in the configuration, which also unneccessarily blocks applications until
a TS LOCK has been acquired. Rather, API and applications will check for
a TS LOCK by utilising the tune fe_op, read_status and get_frontend ops,
which is sufficient.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When AUTO_IFHZ is set and the tuner is supposed to provide proper IF speed
values, it should be possible to have the tuner setup take place before
the demod is configured, else the demod might be configured with either
wrong (old), or even no values at all, which obviously will cause issues.
To set this behaviour in the most flexible way, this is done with a
separate flag instead of making this depend on AUTO_IFHZ.
It should be evaluated if tuning shouldn't take place earlier in all cases
and hardware constellations.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Sony CXD28xx demods may have other tuner types attached to them (e.g.
NXP TDA18212), so don't mandatorily configure and enable the ASCOT
functionality, but make this conditional by a config flag.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some constellations work/need a serial TS transport mode. This adds a flag
that will toggle set up of such mode.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a AUTO_IFHZ flag and a function that will read IF speed values from any
attached tuner if the tuner supports this and if AUTO_IFHZ is enabled, and
else the passed default value (which probably matches Sony ASCOT tuners)
will be passed back. The returned value is then used to calculate the iffeq
which the demod will be programmed with.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some cards/bridges wrap i2c_gate_ctrl handling with a mutex_lock(). This is
e.g. done in ddbridge to protect against concurrent tuner access with
regards to the dual tuner HW, where concurrent tuner reconfiguration can
result in tuning fails or bad reception quality. When the tuner driver
additionally tries to open the I2C gate (which e.g. the tda18212 driver
does) when the demod already did this, this will lead to a deadlock. This
makes the calls to i2c_gatectrl from the demod driver optional when the
flag is set, leaving this to the tuner driver. For readability reasons and
to not have the check duplicated multiple times, the setup is factored
into cxd2841er_tuner_set().
This commit also updates the netup card driver (which seems to be the only
consumer of the cxd2841er as of now).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Throughout the patch series some configuration flags will be added to the
demod driver. This patch prepares this by adding the flags var to
struct cxd2841er_config, which will serve as a bitmask to toggle various
options and behaviour in the driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The way the MAKE_IFFREQ_CONFIG macros are written make it impossible to
pass regular integers for iffreq calculation, since this will cause "SSE
register return with SSE disabled" compile errors. This changes the
calculation into C functions which also might help when debugging. Also,
expand all passed frequencies from MHz to Hz scale.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those demods are programmed in the same way as the CXD2841ER/54ER and can
be handled by this driver. Support added in a way matching the existing
code, supported delivery systems are set according to what each demod
supports.
Updates the type string setting used for printing the "attaching..." log
line aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do unfreeze_regs() directly when accessing the demod registers is done,
and don't have multiple unfreeze's on different conditions, which even
can get prone to errors.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Doing the I2C read operation with two calls to i2c_transfer() causes the
exclusive I2C bus lock of the underlying adapter to be released. While this
isn't an issue if only one demodulator is attached to the bus, having two
or even more causes troubles in that concurrent accesses to the different
demods will cause all kinds of issues due to wrong data being returned on
read operations (for example, the TS config register will be set wrong).
This changes the read_regs() function to do the operation in one go (by
calling i2c_transfer with the whole msg list instead of one by one) to not
loose the I2C bus lock, fixing all sorts of random runtime failures.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This moves the I2C debug dump into the preceding dev_dbg() call by
utilising the %*ph format macro and removes the call to
print_hex_debug_bytes().
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds detection and activation for STV0367-based tuner hardware (namely
CineCTv6 bridge cards and older DuoFlex CT addon modules). Utilises the
extended stv0367 demod driver.
TDA18212 i2c_client/regmap-api code was originally implemented by
Antti Palosaari <crope@iki.fi> in a variant to update the ddbridge code
from the vendor dddvb package (formal ack for these parts received).
Original patch at [1].
When boards with STV0367 are cold-started, there might be issues with the
I2C gate, causing the TDA18212 detection/probe to fail. For these demods,
a workaround (tuner_tda18212_ping) is implemented which probes the tuner
twice on this hardware constellation which will resolve the problem and
put all components into a working state. Other demod/port types won't be
retried.
[1] https://patchwork.linuxtv.org/patch/25146/
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds new i2c_read_regs() function and make i2c_read_reg() wrap into this
with len=1. Required for the tuner_tda18212_ping() and XO2 handling
functions (part of the Sony CXD28xx support patch series).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This - in conjunction with the previous changes - makes it possible to use
the STV0367 DVB-C/T demodulator driver with Digital Devices hardware having
this demodulator soldered on them (namely CineCTv6 bridges and some earlier
DuoFlex CT addon modules).
The changes do the following:
- add a third *_attach function which will make use of a third frontend_ops
struct which announces both -C and -T support (the same as with DD's own
driver stv0367dd). This is necessary to support both delivery systems
on one FE without having to do large conversions to VB2 or the need to
select either -C or -T mode via modparams and the like. Additionally,
the frontend_ops point to new "glue" functions which will then call into
the existing functionality depending on the active delivery system/demod
state (all used functionality works almost OOTB).
- Demod initialisation has been ported from stv0367dd. DD's driver always
does a full init of both OFDM and QAM cores, with some additional things.
The active delivery system is remembered and upon switch, the Demod will
be reconfigured to work in OFDM or QAM mode (that's what the ddb_setup_XX
functions are used for). Note that in QAM mode, the DD demods work with
an IC speed of 58Mhz. It's not very good to perform full reinits upon
Demod mode changes since in very rare occasions this can lead to the I2C
interface or the whole Demod to crash, requiring a powercycle, thus the
flag to perform full reinit is set to disabled.
- A little enum is added for named identifiers of the current Demod state.
Initialisation code/register writes originate from stv0367dd. Permission
to reuse was formally granted by Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Digital Devices uses defaults tables in their stv0367dd demod driver
variant which differ in a few registers, at least enough that no stable
operation can be provided with the tables already present in the driver
(init succeeds and DVB reception works but at least when the driver is
reloaded using rmmod/modprobe, the demod goes into a crashed state in a
way it doesn't react on any I2C command anymore, while even more
side-effects may occur), so there's a good reason to better have another
set of defaults.
Defaults originating from the stv0367dd driver. Permission to reuse them
was formally granted by Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The values used for comparing symbol rates and the resulting conditional
reg writes seem wrong (rates multiplied by ten), so fix those values.
While this doesn't seem to influence operation, it should be fixed anyway.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In some configurations (due to different PIN config, wiring or so), the
QAM FECLock might be signalled using a different register than
F367CAB_QAMFEC_LOCK (e.g. F367CAB_DESCR_SYNCSTATE on Digital Devices hw),
so make that register selectable.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, if_khz is set and provided using the configuration var in
struct stv0367_config. However, in some constellations, the value might be
different for differing channel bandwidths or even -T and -C operation.
When e.g. used in conjunction with TDA18212 tuners, the tuner frontend
might be aware of the different freqs. This factors if_khz retrieval in a
function, which checks a new flag if an automatic retrieval attempt should
be made, and if the tuner provides it, use it whenever needed.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Every time dvb_frontend_ops.set_frontend() is called, an almost full reinit
of the demodulator will be performed. While this might cause a slight delay
when switching channels due to all involved tables being rewritten, it can
even be dangerous in certain causes in that the demod may lock up and
requires to be powercycled (this can happen on Digital Devices hardware).
So this adds a flag if it should be done, and to not change behaviour with
existing card support, it'll be enabled in all cases.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This moves the PLL SETUP code from stv0367ter_init() into a dedicated
function, and also make it possible to configure 58Mhz IC speed at
27MHz Xtal (used on STV0367-based DDB cards/modules in QAM mode).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the *ter and *cab st_register tables into a separate header file and
additionally organize them via a multidimensional array, allowing to add
more tables with differing init values, and also prepare for a base init
table which should contain general setup values. Also add a state var to
store the table triplet to be used.
Also fixes three minor style problems reported by checkpatch.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change defaults table writing so tables can be of dynamic length without
having to keep track of their lengths by adding and evaluating an end
marker (reg 0x0000), also move table writing to a dedicated function to
remove code duplication. Additionally mark st_register tables const since
they're used read-only.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CPAMP log lines generated in stv0367_ter_check_cpamp() are printed
everytime tuning succeeds or fails, quite cluttering the normal kernel log.
Use dprintk() instead of printk(KERN_ERR...) so that if the information is
needed, it'll be printed when the stv_debug modparam is enabled.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some hardware and bridges (namely ddbridge) require that tuner access is
limited to one concurrent access and wrap i2c gate control with a
mutex_lock when attaching frontends. According to vendor information, this
is required as concurrent tuner reconfiguration can interfere each other
and at worst cause tuning fails or bad reception quality.
If the demod driver does gate_ctrl before setting up tuner parameters, and
the tuner does another I2C enable, it will deadlock forever when gate_ctrl
is wrapped into the mutex_lock. This adds a flag and a conditional before
triggering gate_ctrl in the demodulator driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I would like to replace Kyungmin Park, who is no longer interested in
maintaining S5P-CEC driver. I have access to various Exynos boards. I also
already did some tests of this driver and helped enabling it on various
Exynos boards. The driver itself is no longer in staging, so lets fix the
path too and add DT bindings file pattern match. Also change the mailing
list from ARM generic to Samsung SoC specific to get more attention and
easier review in the future.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are multiple places where arrays or otherwise variable sized
buffer are allocated through V4L2 core code, including things like
controls, memory pages, staging buffers for ioctls and so on. Such
allocations can potentially require an order > 0 allocation from the
page allocator, which is not guaranteed to be fulfilled and is likely to
fail on a system with severe memory fragmentation (e.g. a system with
very long uptime).
Since the memory being allocated is intended to be used by the CPU
exclusively, we can consider using vmalloc() as a fallback and this is
exactly what the recently merged kvmalloc() helpers do. A kmalloc() call
is still attempted, even for order > 0 allocations, but it is done
with __GFP_NORETRY and __GFP_NOWARN, with expectation of failing if
requested memory is not available instantly. Only then the vmalloc()
fallback is used. This should give us fast and more reliable allocations
even on systems with higher memory pressure and/or more fragmentation,
while still retaining the same performance level on systems not
suffering from such conditions.
While at it, replace explicit array size calculations on changed
allocations with kvmalloc_array().
Purposedly not touching videobuf1, as it is deprecated, has only few
users remaining and would rather be seen removed instead.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a wrapper around the media entity get_fwnode_pad operation.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The optional operation can be used by entities to report how it maps its
fwnode endpoints to media pad numbers. This is useful for devices which
require advanced mappings of pads.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a check for v4l2_dev to v4l2_async_notifier_register() as to fail as
early as possible since this will fail later in v4l2_async_test_notify().
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The new Renesas R-Car H3 ES2.0 platforms have a new hw version register.
Update the driver accordingly, defaulting to the new hw revision, and
differentiating the older revision as ES1
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove useless variable assignment in function tc358743_isr().
The value stored in variable _intstatus_ at line 1299 is
overwritten at line 1302, just before it can be used.
Addresses-Coverity-ID: 1397678
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Updating my personal email address in solo6x10.
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Anton Sviridenko is now in charge of drivers in Bluecherry.
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The davinci VPIF is a single hardware block, but the existing driver
is broken up into a common library (vpif.c), output (vpif_display.c) and
intput (vpif_capture.c).
When migrating to DT, to better model the hardware, and because
registers, interrupts, etc. are all common,it was decided to
have a single VPIF hardware node[1].
Because davinci uses legacy, non-DT boot on several SoCs still, the
platform_drivers need to remain. But they are also needed in DT boot.
Since there are no DT nodes for the display/capture parts in DT
boot (there is a single node for the parent/common device) we need to
create platform_devices somewhere to instantiate the platform_drivers.
When VPIF display/capture are needed for a DT boot, the VPIF node
will have endpoints defined for its subdevs. Therefore, vpif_probe()
checks for the presence of endpoints, and if detected manually creates
the platform_devices for the display and capture platform_drivers.
[1] Documentation/devicetree/bindings/media/ti,da850-vpif.txt
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
'call_ptr_memop' can return NULL, so we must test its return value with
'IS_ERR_OR_NULL'. Otherwise, the test 'if (mem_priv)' is meaningless.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As long as only one CODA context is running we get alternating device_run()
and wait_for_completion() calls, but when more then one CODA context is
active, other VDOA slots can be inserted between those calls for one context.
Make sure to wait on job completion before running a different context and
before destroying the currently active context.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This implements a simple handler for the case where decode did not finish
sucessfully. This might be helpful during normal streaming, but for now it
only handles the case where the context would deadlock with userspace,
i.e. userspace issued DEC_CMD_STOP and waits for EOS, but after the failed
decode run we would hold the context and wait for userspace to queue more
buffers.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mvcol buffer needs to be placed behind the chroma plane(s), so
use the real offset including any required rounding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This makes firmware name and path part of venus_resources
structure and initialize it properly depending on the SoC and
firmware version.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds support for V4L2_CID_MIN_BUFFERS_FOR_CAPTURE get control
in venus decoder, it is usable in case when the userspace wants
to know minimum capture buffers before calling request_buf for
capture queue in mem2mem drivers. Also this will fix an issue
found gstreamer v4l2videodec element, i.e. the video decoder
element cannot continue because the buffers are insufficient.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
