This prepares the only place which uses the EWMA library so far for the
performance improved implementation coming up, which requires factor and
weight to be a power of two.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This file pattern is not currently shown as maintained
by atheros. Perhaps it should be?
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last_tx_rate field was also updated for non-data frames that are
often sent with a lower rate (for example management frames at 1 Mbps).
This is confusing when the data rate is actually much higher.
Hence, only update the last_tx_rate field with tx rate information
gathered from last data frames.
If the rate control algorithm filled in txrc.reported_rate we don't need
to verify this information.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On WiSoc we cannot access mac register before it is resetted.
It will crash hardware otherwise.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AHB specific functions are now in ahb.c file. AHB bus is
compiled in when CONFIG_ATHEROS_AR231X is set in kernel.
All other platforms will use PCI bus.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add bus dependent revision read function which is used to
determine chipset's MAC before hardware is initialized.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be able to support other busses than PCI check if pci device
structure is initialized.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split pci initialization into hardware specific
functions and softc structure initialization.
Make function naming similar to ones ath9k.
Introduce ath_bus_opts in ath5k for later
AHB bus integration.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last patch with the same title was for mac80211 ops, accidentally.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create a new chapter about SMPS in the
driver API part of the mac80211 book and
populate it with the existing docs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add some existing documentation about station
handling to a new chapter about advanced APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Publish the documentation for the interface
iteration functions in the right section of
the book.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Include the aggregation documentation in the
docbook, split up by public and internal docs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add an API chapter to the rate control part of
the mac80211 book and populate it with some
existing documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There isn't a clear TX documentation yet, so
put these into the misc section for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put them along with their "regular" versions for
now, we should write more docs in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create a new chapter for the mac80211 workqueue
that contains the documentation written for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just include them in the list of functions,
there aren't any more detailed docs (yet).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Invert test and return early.
Move variable declarations to local scope.
Don't initialize variables to 0 unnecessarily.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes debugfs problems when a phy is renamed,
and is able to remove a bit of code that is no longer
needed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specs were updated plus we become wl compatible.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make it possible to read out the attributes, till now only show on
dmesg, through sysfs.
This patch was some time in OpenWrt.
Signed-off-by: Bernhard Loos <bernhardloos@googlemail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 916448e77f.
"As far as I can tell, either of these patches breaks multiple VIF
scenarios. I'm not sure exactly why, but I had to revert this to
get any of my interfaces to associate."
-- Ben Greear <greearb@candelatech.com>
http://marc.info/?l=linux-wireless&m=129123368719339&w=2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few LNA control related flags were also specified as a bitfields, however
for some strange reason they were written in big-endian order this time.
Fix this by using flags instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.
Cc:stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the module parameter name to bt_ch_inhibition from
bt_ch_announce to better describe the functionality
In order to allow Bluetooth to activate a smart AFH mechanism
and to maximize its available bandwidth the WiFi will request
BT Core to inhibit its activity in channels that interfere
with WiFi activity (and vice versa) if bt_ch_inhibition is enabled
Set module parameter "bt_ch_inhibition=0" will disable the channel
inhibition function
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If driver is on the way down, there is no need to send
RXON to uCode, check the condition before continuous the process.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
PCI L1 Active needs to be disabled while loading the uCode so that the bus
doesn't go to sleep. The enablement of L1 Active should be done after
the uCode has sent the ALIVE response. The enablement of L1 Active was
missing.
Enabling L1 Active allows to save power if the BIOS / bus driver allows
it.
I measured the power consumption while not associated and
idle/associated:
L1 Active disabled: 39 mA = 130mW
L1 Active enabled: 6 mA = 20 mW
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
During reprogram stations, do not send link quality command.
uCode will crash if receive link quality command for invalid station
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Remove extra spaces from legal text so that legal stuff looks
the same for all bluetooth code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
