The OTG arrangement on the LinkSprite pcDuino v3 Nano is the same as the
pcDuino 1/2/3: the OTG port's 5V line is connected directly to the 5V
bus (it's not switchable), and the OTG port's ID pin is connected to PH4
on the A20.
Tested successfully in both host and device modes.
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull networking fixes from David Miller:
1) Account for extra headroom in ath9k driver, from Felix Fietkau.
2) Fix OOPS in pppoe driver due to incorrect socket state transition,
from Guillaume Nault.
3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.
4) Power management fixes for iwlwifi, from Johannes Berg.
5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.
6) Fix dst_entry usage in ARP replies, from Jiri Benc.
7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.
8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.
9) Various resource allocation/freeing cures in DSA< from Neil
Armstrong.
10) A series of bug fixes in the openvswitch conntrack support, from
Joe Stringer.
11) Fix two cases (BPF and act_mirred) where we have to clean the sender
cpu stored in the SKB before transmitting. From WANG Cong and
Alexei Starovoitov.
12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
Achiad Shochat.
13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
configuration via ethtool. From Yuval Mintz.
14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
'dev' is NULL, from Eric Biederman.
15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.
16) kcalloc() gstrings ethtool buffer before having driver fill it in,
in order to prevent kernel memory leaking. From Joe Perches.
17) Fix mixxing rt6_info initialization for blackhole routes, from
Martin KaFai Lau.
18) Kill VLAN regression in via-rhine, from Andrej Ota.
19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.
20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.
21) Scrube SKBs when pushing them between namespaces in openvswitch,
from Joe Stringer.
22) bcmgenet enables link interrupts too early, fix from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net: bcmgenet: Fix early link interrupt enabling
tunnels: Don't require remote endpoint or ID during creation.
openvswitch: Scrub skb between namespaces
xen-netback: correctly check failed allocation
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
netlink: Trim skb to alloc size to avoid MSG_TRUNC
net: add pfmemalloc check in sk_add_backlog()
via-rhine: fix VLAN receive handling regression.
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Bluetooth: Fix initializing conn_params in scan phase
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
Bluetooth: Fix remove_device behavior for explicit connects
Bluetooth: Fix LE reconnection logic
Bluetooth: Fix reference counting for LE-scan based connections
Bluetooth: Fix double scan updates
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
tipc: move fragment importance field to new header position
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
tipc: eliminate risk of stalled link synchronization
...
Install a non-faulting handler just before unmasking imprecise aborts
and switch back to the regular one after unmasking is done.
This catches any pending imprecise abort that the firmware/bootloader
may have left behind that would normally crash the kernel at that point.
As there are apparently a lot of bootlaoders out there that do such a
thing it makes sense to handle it in the common startup code.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the host toolchain is not glibc based then the arm kernel build
fails with
HOSTCC arch/arm/vdso/vdsomunge
arch/arm/vdso/vdsomunge.c:48:22: fatal error: byteswap.h: No such file or directory
Observed: with omap2plus_defconfig and compile on Mac OS X with arm ELF
cross-compiler.
Reason: byteswap.h is a glibc only header.
Solution: replace by private byte-swapping macros (taken from
arch/mips/boot/elf2ecoff.c and kindly improved by Russell King)
Tested to compile on Mac OS X 10.9.5 host.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The second macb is present on all the sama5d4 SoCs. Let's add a node
reflecting it in the device tree.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
MMC data lines may be left floating if nothing is currently driving the
data lines, which is the case when mmc is in idle state, thus consuming
a useless extra amount of power. Add pullup on mmc2 data signals in the
same way it was previously done for mmc0 and mmc1.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add regulator nodes of PMIC ACT8945A chip on the board.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix instances of "disable" instead of "disabled"
in the at91rm9200 dtsi.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The PMC is not only used to drive the clocks but also has some registers
related to other functions. One of those is for example the USB gadget
bias.
Using a syscon allows to properly separate those functions.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some omaps are producing imprecise external aborts because we are
wrongly trying to init SRAM for device tree based booting. Only
omap3 is still using the legacy SRAM code, so we need to make it
omap3 specific. Otherwise we can get errors like this on at least
dm814x:
Unhandled fault: imprecise external abort (0xc06) at 0xc08b156c
...
(omap_rev) from [<c08b12e0>] (omap_sram_init+0xf8/0x3e0)
(omap_sram_init) from [<c08aca0c>] (omap_sdrc_init+0x10/0xb0)
(omap_sdrc_init) from [<c08b581c>] (pdata_quirks_init+0x18/0x44)
(pdata_quirks_init) from [<c08b5478>] (omap_generic_init+0x10/0x1c)
(omap_generic_init) from [<c08a57e0>] (customize_machine+0x1c/0x40)
(customize_machine) from [<c00098a4>] (do_one_initcall+0x80/0x1dc)
(do_one_initcall) from [<c08a2ec4>] (kernel_init_freeable+0x218/0x2e8)
(kernel_init_freeable) from [<c063a554>] (kernel_init+0x8/0xec)
(kernel_init) from [<c000f890>] (ret_from_fork+0x14/0x24)
Let's fix the issue by making sure omap_sdrc_init only gets called for
omap3. To do that, we need to have compatible "ti,omap3" in the dts
files. And let's also use "ti,omap3630" instead of "ti,omap36xx" like
we're supposed to.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "snps,quirk-frame-length-adjustment" property to
USB3 node for erratum A009116. This property provides
value of GFLADJ_30MHZ for post silicon frame length
adjustment.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The property name should be "gpio", not "gpios". Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix a typo, replacing "pinctrl-name" by "pinctrl-names"
in the Phytec phyFLEX-i.MX6 Quad dtsi.
Also fix a typo in the board name
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct core clock of spdif is SPDIF_GCLK, which is added to
clock tree. So the dts also need to be updated.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable NAND access by adding pinmux and NAND flash controller node
to device tree. The NAND chips currently used on the Colibri VF61
requires 8-bit ECC per 512 byte page, hence specify 32-bit ECC
strength per 2k page size.
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the NAND flash controller (NFC) peripherial. The driver
supports the SLC NAND chips found on Freescale's Vybrid Tower System
Module. The Micron NAND chip on the module needs 4-bit ECC per 512
byte page. Use 24-bit ECC per 2k page, which is supported by the
driver.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Based on i.MX6 Quad with 4GB of DDR3.
http://boundarydevices.com/product/nitrogen6max/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the different touchscreens that can be connected using
the displays available for this board.
http://boundarydevices.com/product-category/displays/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the 7" LCD display available for Sabrelite:
http://boundarydevices.com/product/7-800x480-display/
Also add label to backlight_lcd and connect it to the panel.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the 7" LCD display available for Nitrogen6x:
http://boundarydevices.com/product/7-800x480-display/
Also add label to backlight_lcd and connect it to the panel.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree node for touchscreen support on Colibri VF50. The
touchscreen functionality on VF50 uses the ADC channels of Vybrid
and some GPIOs. Also add pinctrl nodes for proper pinmux.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree node to support iomuxc-lpsr controller, fsl,input-sel
phandle allows to get input select register base address which is
shared from main iomuxc controller.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The INA220 monitors both shunt drop and supply voltage.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds dma-coherent property for eTSEC nodes, so
coherent DMA operations are supported.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for USBOTG1 and USBOTG2.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add imx6ul touchscreen controller support.
TSC module need ADC2 module to measure the touchscreen
coordinate value. This patch put TSC and ADC2 together,
make ADC2 module only be used for TSC, can't be used as
a normal ADC.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DCP block present on MX6SL is compatible with the one on MX28,
so add the compatible string and also complete the interrupt entries.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch enables On Chip OTP support for i.MX23 and i.MX28 SoCs,
but keeps the old compatible string.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-sdb board has a eMMC5.0 on usdhc3. This eMMC support HS400.
This patch add usdhc3 support for HS400
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6UL can be powered off by programming SNVS.
When long press ON/OFF button(5 seconds),
PMIC_ON_REQ pin will be set to low and external
PMIC will be powered off.
And system can be powered on by long press ON/OFF
button again.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SRAM support for i.MX6UL, it has 128KB ocram
starting from 0x900000.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The R8 is a new Allwinner SoC based on the A13. While both are very
similar, there's still a few differences. Introduce a new compatible to
deal with them.
In order to have a consistent naming, instead of mentioning the Allwinner
A series as the machine name, switch to sun4i/sun5i like what is done for
the other families.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a pinmux setting for using mmc2 in regular 4 bit mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When the gpio interrupt bindings where changed to add a bank to the
specifier list, the r_pio nodes of A23/A31/A33 where not updated to
match and neither was the pio node of the A80, this fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With omap5-board-common.dtsi, we can now easily add support for various omap5
board variants. Let's add minimal support for isee igepv5.
So far I've tested that basic things work, such as serial, USB Ethernet, HDMI
and WLAN.
Note that like omap5-uevm, these boards seem to need to reserve 16MB for a
trap section as in commit 03178c66d2 ("ARM: dts: omap5-evm: Update
available memory to 2032 MB") and also noted in a u-boot commit at
http://marc.info/?l=u-boot&m=134376852603255 and also at
http://patchwork.ozlabs.org/patch/159881/.
Not sure why this is not needed for omap5-cm-t54.dts, maybe because of
different u-boot configuration.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like thevarious omap5-uevm models and igepv5 are very similar. So let's
create omap5-board-common.dtsi to allow fixing up things properly for mainline
kernel to support all these.
Even if we eventually end up having only PMIC + MMC + eMMC + SDIO WLAN + SATA +
USB + HDMI configuration in the omap5-board-common.dtsi, this is the easiest
way to add support for other boards rather than diffing various versions of
out of tree dts files.
My guess is that also omap5-sbc-t54.dts can use this, but I don't have that
board so that will need to be dealt with later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 99f84cae43 ("ARM: dts: add wl12xx/wl18xx bindings") added
device tree bindings for the TI WLAN SDIO on many omap variants.
I recall wondering how come omap5-uevm did not have the WLAN
added and this issue has been bugging me for a while now, and
I finally tracked it down to a bad pinmux regression, and a missing
deferred probe handling for the 32k clock from palmas that's
requested by twl6040.
Basically 392adaf796 ("ARM: dts: omap5-evm: Add mcspi data")
added pin muxing for mcspi4 that conflicts with the onboard
WLAN. While some omap5-uevm don't have WLAN populated, the
pins are not reused for other devices. And as the SDIO bus
should be probed, let's try to enable WLAN by default.
Let's fix the regression and add the WLAN configuration as
done for the other boards in 99f84cae43 ("ARM: dts: add
wl12xx/wl18xx bindings"). And let's use the new MMC pwrseq for
the 32k clock as suggested by Javier Martinez Canillas
<javier@dowhile0.org>.
Note that without a related deferred probe fix for twl6040,
the 32k clock is not initialized if palmas-clk is a module
and twl6040 is built-in.
Let's also use the generic "non-removable" instead of the
legacy "ti,non-removable" property while at it.
And finally, note that omap5 seems to require WAKEUP_EN for
the WLAN GPIO interrupt.
Fixes: 392adaf796 ("ARM: dts: omap5-evm: Add mcspi data")
Cc: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On boards with more than 2GB of RAM booting goes wrong with things not
working and we're getting lots of l3 warnings:
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x260/0x384()
44000000.ocp:L3 Custom Error: MASTER MMC6 TARGET DMM1 (Idle):
Data Access in User mode during Functional access
...
[<c044e158>] (scsi_add_host_with_dma) from [<c04705c8>]
(ata_scsi_add_hosts+0x5c/0x18c)
[<c04705c8>] (ata_scsi_add_hosts) from [<c046b13c>]
(ata_host_register+0x150/0x2cc)
[<c046b13c>] (ata_host_register) from [<c046b38c>]
(ata_host_activate+0xd4/0x124)
[<c046b38c>] (ata_host_activate) from [<c047f42c>]
(ahci_host_activate+0x5c/0x194)
[<c047f42c>] (ahci_host_activate) from [<c0480854>]
(ahci_platform_init_host+0x1f0/0x3f0)
[<c0480854>] (ahci_platform_init_host) from [<c047c9dc>]
(ahci_probe+0x70/0x98)
[<c047c9dc>] (ahci_probe) from [<c04220cc>]
(platform_drv_probe+0x54/0xb4)
Let's fix the issue by enabling ZONE_DMA for LPAE. Note that we need to
limit dma_zone_size to 2GB as the rest of the RAM is beyond the 4GB limit.
Let's also fix things for dra7 as done in similar patches in the TI tree
by Lokesh Vutla <lokeshvutla@ti.com>.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The z2 machine calls pxa27x_set_pwrmode() in order to power off
the machine, but this function gets discarded early at boot because
it is marked __init, as pointed out by kbuild:
WARNING: vmlinux.o(.text+0x145c4): Section mismatch in reference from the function z2_power_off() to the function .init.text:pxa27x_set_pwrmode()
The function z2_power_off() references
the function __init pxa27x_set_pwrmode().
This is often because z2_power_off lacks a __init
annotation or the annotation of pxa27x_set_pwrmode is wrong.
This removes the __init section modifier to fix rebooting and the
build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ba4a90a6d8 ("ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This fixes the following sparse warnings:
arch/arm/mach-pxa/raumfeld.c:510:24: warning: symbol 'raumfeld_w1_gpio_device' was not declared. Should it be static?
arch/arm/mach-pxa/raumfeld.c:632:31: warning: symbol 'raumfeld_spi_platform_data' was not declared. Should it be static?
arch/arm/mach-pxa/raumfeld.c:851:28: warning: symbol 'audio_va_initdata' was not declared. Should it be static?
arch/arm/mach-pxa/raumfeld.c:883:28: warning: symbol 'audio_dummy_initdata' was not declared. Should it be static?
arch/arm/mach-pxa/raumfeld.c:931:28: warning: symbol 'max8660_v6_subdev_data' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Currently apart from dra7, omap5 and amx3 all the other SoCs
are identified using cpu_is_* functions which is not right since
they are all SoCs(System on Chips). Hence changing the SoC
identification code to use soc_is instead of cpu_is and keeping
defines for cpu_is where needed. This allows us to replace the
rest of cpu_is usage along with other fixes as needed.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Keerthy <j-keerthy@ti.com>
[tony@atomide.com: reworked the soc.h changes to minimum]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The newest revisions of A388-GP (v1.5 and higher) support only
DAT3-based card detection. Revisions < v1.5 based on GPIO detection
via I2C expander, but this solution is supposed to be deprecated on
new boards. In order to satisfy all type of hardware this commit
changes card detection to use software polling mechanism. Also a
comment is added on possible card detection options in A388-GP
DT board file.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The naming for the cpu_is macros is confusing as the CPU is separate
and within the SoC. Let's rename all the macros to soc_is, and let's
define cpu_is also for the ones still in use. Then we can just remove
the cpu_is macros once the users are fixed up.
To keep the chances of breaking anything, the changes were
generated with the following regular expressions:
s/cpu_is/soc_is/g
s/CPU/SoC/g
Then the list of existing cpu_is users was generated with:
$ $ grep -o -e 'cpu_is_.\+()' arch/arm/mach-omap2/*.[chS] | \
cut -d: -f2 | sort | uniq
And added to the end of the soc.h.
I decided to rework the earlier patches by Keerthy <j-keerthy@ti.com>
to keep changes down to minimum to avoid potential errors and stick
to just search and replace.
Signed-off-by: Tony Lindgren <tony@atomide.com>
now that we have a working 32k clocksource driver,
we can limit HWMOD usage to non-DT boots and rely
on clocksource_of_init() every time we boot
with DT.
While at that, also make sure that we don't disable
the 32-counter device so it gets probed by its driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this function is not only about the 32k sync
timer, it's OMAP's generic init_time implementation.
Let's rename it to make that detail easier to
notice.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If booting with DT, let's make sure to always
call clocksource_of_init() as this will make
it easier to move timer code to drivers/clocksource
in the future.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The sorting policy for this file is alphabetically.
Reorder all nodes, that are out of place.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The NMI interrupt controller is in charge of the NMI pin exposed by
the SoC to the PMIC. The PMIC signals interrupts through this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add FPGA manager to device tree for SoCFPGA.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
instead of constantly defining a small wrapper
around __omap_sync32k_timer_init(), let's define
a generic one which can be used by all OMAPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
__omap_sync32k_timer_init(), now takes the clock
source as a parameter. This means we no longer need
__omap_gptimer_init().
Note that __omap_sync32k_timer_init() will be
renamed in a follow-up patch as it's not longer 32k
source specific.
Signed-off-by: Felipe Balbi <balbi@ti.com>
as it turns out, __omap_gptimer_init() and
__omap_sync32k_timer_init() are essentially
the same thing, but __omap_gptimer_init() wants
to always use gptimer.
Instead of forcing all those devices to pass
a use_gptimer cmdline argument, we add a new
function argument to __omap_sync32k_timer_init()
in preparation to deleting __omap_gptimer_init().
On a follow-up patch, we will remove uses of
__omap_gptimer_init() and replace them with
__omap_sync32k_timer_init() and pass the last
argument as true.
Signed-off-by: Felipe Balbi <balbi@ti.com>
those macros just make it a lot more difficult
to grep around and actually find similarities.
In this patch, we will simply remove them and
replace with actual functions and later commits
will come to further clean this up.
Signed-off-by: Felipe Balbi <balbi@ti.com>
omap4_local_timer_init() can be used by other
platforms as is. At least AM437x wants to use
it. Instead of making omap4-only and providing
a stub for builds without OMAP4, we can just
make sure that function is always available
for all SoCs that need it.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* Implement id_table driver matching in SMD
* Avoid NULL pointer exception on remove of SMEM
* Reorder SMEM/SMD configs
* Make qcom_smem_get() return a pointer
* Handle big endian CPUs correctly in SMEM
* Represent SMD channel layout in structures
* Use __iowrite32_copy() in SMD
* Remove use of VLAIs in SMD
* Handle big endian CPUs correctly in SMD/RPM
* Handle big endian CPUs corretly in SMD
* Reject sending SMD packets that are too large
* Fix endianness issue in SCM __qcom_scm_is_call_available
* Add missing prototype for qcom_scm_is_available()
* Correct SMEM items for upper channels
* Use architecture level to build SCM correctly
* Delete unneeded of_node_put in SMD
* Correct active/slep state flagging in SMD/RPM
* Move RPM message ram out of SMEM DT node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hprv
-----END PGP SIGNATURE-----
Merge tag 'qcom-soc-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm into next/drivers
Pull "Qualcomm ARM Based SoC Updates for 4.4" from Andy Gross:
* Implement id_table driver matching in SMD
* Avoid NULL pointer exception on remove of SMEM
* Reorder SMEM/SMD configs
* Make qcom_smem_get() return a pointer
* Handle big endian CPUs correctly in SMEM
* Represent SMD channel layout in structures
* Use __iowrite32_copy() in SMD
* Remove use of VLAIs in SMD
* Handle big endian CPUs correctly in SMD/RPM
* Handle big endian CPUs corretly in SMD
* Reject sending SMD packets that are too large
* Fix endianness issue in SCM __qcom_scm_is_call_available
* Add missing prototype for qcom_scm_is_available()
* Correct SMEM items for upper channels
* Use architecture level to build SCM correctly
* Delete unneeded of_node_put in SMD
* Correct active/slep state flagging in SMD/RPM
* Move RPM message ram out of SMEM DT node
* tag 'qcom-soc-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm:
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
soc: qcom: smd_rpm: Handle big endian CPUs
soc: qcom: smd: Remove use of VLAIS
soc: qcom: smd: Use __iowrite32_copy() instead of open-coding it
soc: qcom: smd: Represent channel layout in structures
soc: qcom: smem: Handle big endian CPUs
soc: qcom: Make qcom_smem_get() return a pointer
soc: qcom: Reorder SMEM/SMD configs
soc: qcom: smem: Avoid NULL pointer exception on remove
soc: qcom: smd: Implement id_table driver matching
- use the non-self-clearing reset register
- add cpu hotplug support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=khG4
-----END PGP SIGNATURE-----
Merge tag 'berlin-soc-for-4.4-2' of git://git.infradead.org/users/hesselba/linux-berlin into next/soc
Merge "Marvell Berlin SoC for 4.4 take 2" from Sebastian Hesselbarth:
- use the non-self-clearing reset register
- add cpu hotplug support
* tag 'berlin-soc-for-4.4-2' of git://git.infradead.org/users/hesselba/linux-berlin:
arm: berlin: add CPU hotplug support
arm: berlin: use non-self-cleared reset register to reset cpu
CONFIG_FIXED_PHY is needed to have Ethernet working on STi boards.
Select it as built-in since RootFS is accessible from NFS on these boards.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- DCAN sleep pins for am437x-gp-evm
- A series of changes to add audio support for dra7
- Add support for gpio keys and LEDs on dra7
- Regulator clean-up for am335x-wega
- A series of changes to enable IOMMUs and mailboxes for dra7
accelerators
- Add support for am335x-bonegreen
- Fix up GPIO flags where 0 was used instead of GPIO_ACTIVE_HIGH
- Fix omap3-lilly-am33x IRQ level flag
- Remove duplicate uart2 pinmux for igep and fix indentation and
update igep to use pinctrl macros for the register offsets
- Fix MMC cd-gpios usage
Note that this branch is against v4.3-rc4 as that contains critical
MMC related fixes to boot with MMC working on most omaps.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Sbup
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree changes for omaps for v4.4 merge window:" from Tony Lindgren:
- DCAN sleep pins for am437x-gp-evm
- A series of changes to add audio support for dra7
- Add support for gpio keys and LEDs on dra7
- Regulator clean-up for am335x-wega
- A series of changes to enable IOMMUs and mailboxes for dra7
accelerators
- Add support for am335x-bonegreen
- Fix up GPIO flags where 0 was used instead of GPIO_ACTIVE_HIGH
- Fix omap3-lilly-am33x IRQ level flag
- Remove duplicate uart2 pinmux for igep and fix indentation and
update igep to use pinctrl macros for the register offsets
- Fix MMC cd-gpios usage
Note that this branch is against v4.3-rc4 as that contains critical
MMC related fixes to boot with MMC working on most omaps.
* tag 'omap-for-v4.4/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (33 commits)
ARM: dts: omap3-igep: Use OMAP3_CORE1_IOPAD pinmux macro
ARM: dts: dra7xx: am57xx: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: am43xx: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: am335x: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: omap3-igep0020: Remove duplicate uart2 pinmux
ARM: dts: omap3-igep: Fix indentation
ARM: dts: omap3-lilly-a83x: Don't use IRQ level flag for a GPIO
ARM: dts: DRA74x: Add IOMMU nodes for DSP2
ARM: dts: DRA7: Add common IOMMU nodes
ARM: dts: DRA74x: Add dsp2_system syscon node
ARM: dts: DRA7: Add dsp1_system syscon node
ARM: dts: Use defined GPIO constants in flags cell for OMAP2+ boards
ARM: dts: Add am335x-bonegreen
ARM: dts: beagle-x15: Enable the system mailboxes 5 and 6
ARM: dts: dra72-evm: Enable the system mailboxes 5 and 6
ARM: dts: dra7-evm: Enable the system mailboxes 5 and 6
ARM: dts: DRA72x: Add IPC sub-mailbox nodes for IPU1, IPU2 & DSP1
ARM: dts: DRA74x: Add IPC sub-mailbox nodes for all IPUs & DSPs
ARM: dts: am335x-wega: Clean up regulators
ARM: dts: dra7-evm: add gpio key support
...
- Enable SPIFI Flash and JFFS2 to support rootfs on Flash memory
- Enable USB Phy, mass storage and SCSI to support USB memory
- Enable PCF857x and JC42 I2C devices found on Hitex board
- Enable PL172 to support memory mapped NOR Flash
- New LPC18xx drivers: I2C, Watchdog, SCT PWM and RTC
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "Broadcom soc changes for v4.4 (try 2)" from Florian Fainelli:
This pull request contains the following Broadcom SoC platform and driver changes:
- Brian Norris create a drivers/soc/brcmstb/ stub as a place holder for SoC-specific
code which is coming next
- Florian Fainelli adds support for configuring the BCM7xxx SoCs Bus Interface Unit
with their specific write-pairing setting, which must be saved and restored during
system-wide suspend/resume, and consequently updates the brcmstb machine code to
initialize the BIU
- Jon Mason adds support for the Northstar Plus SoCs by introducing a custom machine
descriptor matching their compatible string and setting up the PL310 L2 cache and
enabling the relevant ARM errata for their Cortex-A9
* tag 'arm-soc/for-4.4/soc' of http://github.com/Broadcom/stblinux:
ARM: brcmstb: Setup BIU control registers during boot
soc: brcmstb: Add Bus Interface Unit control setup
soc: add stubs for brcmstb SoC's
ARM: NSP: Add basic support for Broadcom Northstar Plus SoC
L2 caches optimization for Armada XP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlYX5kYACgkQCwYYjhRyO9XRAACgh9ZuCj/Bxgsql5tHL2fLPhMw
OzwAn3RJqjzRRMLcZ/TmgTPNbNwz3hEB
=bO2O
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-4.4-1' of git://git.infradead.org/linux-mvebu into next/soc
Merge "mvebu soc for 4.4 (part 1)" from Gregory CLEMENT:
L2 caches optimization for Armada XP
* tag 'mvebu-soc-4.4-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add support to clear shared L2 bit on Armada XP
- Remove legacy omap3 ISP code as the driver is DT only
- Remove VoiceBlue board support as it's been unused over
10 years now
- Remove unused polarity control macros for TWL
- Remove two unneeded semicolons
- Remove unused core dpll code for reprogramming the rates
Note that this branch is against v4.3-rc4 as that contains critical
MMC related fixes to boot with MMC working on most omaps.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=d5vJ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/cleanup-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Merge "Clean-up for omaps for v4.4 merge window" from Tony Lindgren:
- Remove legacy omap3 ISP code as the driver is DT only
- Remove VoiceBlue board support as it's been unused over
10 years now
- Remove unused polarity control macros for TWL
- Remove two unneeded semicolons
- Remove unused core dpll code for reprogramming the rates
Note that this branch is against v4.3-rc4 as that contains critical
MMC related fixes to boot with MMC working on most omaps.
* tag 'omap-for-v4.4/cleanup-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: clock: remove un-used core dpll re-program code
ARM: OMAP2+: Remove unneeded semicolons
ARM: OMAP3: vc: Remove unused macros
ARM: OMAP1: Remove board support for VoiceBlue board
ARM: OMAP2+: Remove legacy OMAP3 ISP instantiation
use the CR_C define instead of a literal value
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlYX5PQACgkQCwYYjhRyO9WE/wCdHL0jkJKufbzUMo3P1ZTfGvKR
iHUAn2hB1f1k3xKFV8HP6XLO7jhc29LJ
=NZow
-----END PGP SIGNATURE-----
Merge tag 'mvebu-cleanup-4.4-1' of git://git.infradead.org/linux-mvebu into next/cleanup
Merge "mvebu cleanup for 4.4 (part 1)" from Gregory CLEMENT:
use the CR_C define instead of a literal value
* tag 'mvebu-cleanup-4.4-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Use a CR_C constant instead of a hard-coded one
Add cpu hotplug support for berlin SoCs such as BG2 and BG2Q. These SoC
don't support power off cpu independently, but we also want cpu hotplug
support in these SoCs. We achieve this goal by putting the dying CPU in
WFI state after the coherency is disabled, then asserting the dying CPU
reset bit to put the CPU in reset state.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
In Berlin SoCs, there are two kinds of cpu reset control registers: the
first one's corresponding bits will be self-cleared after some cycles,
while the second one's bits won't. Previously the first kind of reset
control register is used, this patch uses the second kind one to prepare
for the next hotplug commit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
While the addition of these properties is technically correct it unveils
a bug with deferred probe. The problem is that the presence of the gpio-
range property causes the gpio-tegra driver to defer probe (it needs the
pinctrl driver to be ready). That's technically correct, but it causes a
couple of issues:
- The keyboard on Chromebooks stops working. The reason for that is
that the gpio-tegra device has not registered an IRQ domain by the
time the EC SPI device is registered, hence the interrupt number
resolves to 0. This is technically a bug in the SPI core, since it
should really resolve the interrupt at probe time and defer if the
IRQ domain isn't available yet. This is similar to what's done for
I2C and platform device already.
- The gpio-tegra device deferring probe means that it is moved to the
end of the dpm_list. This list defines the suspend/resume order for
devices. However the core lacks a way to move all users of the
gpio-tegra device to the end of the dpm_list at the same time. This
in turn results in a subtle bug on Jetson TK1, where the gpio-keys
device is used to expose the power key as input. The power key is a
convenient way to wake the system from suspend. Interestingly, the
gpio-keys device ends up getting probed at a point after gpio-tegra
has been probed successfully from having been deferred earlier. As
such the driver doesn't need to defer the probe itself, and hence
the device isn't moved to the end of the dpm_list. This causes the
gpio-tegra device to be suspended before gpio-keys, which in turn
leaves gpio-keys unable to wake the system from suspend.
There are patches in the works to fix both of the above issues, but they
are too involved to make it into v4.3, so in the meantime let's fix the
regressions by commenting out the gpio-ranges properties until the fixes
have landed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Enable the following on the porter board:
I2C2, PCI, PCIe, QSPI, SATA0, SDHI0/2, USB PHY and VIN0/ADV7180.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8OHS
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.4" from Simon Horman:
* Enable the following on the porter board:
I2C2, PCI, PCIe, QSPI, SATA0, SDHI0/2, USB PHY and VIN0/ADV7180.
* tag 'renesas-dt2-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: porter: enable internal PCI and USB PHY
ARM: shmobile: porter: enable PCIe
ARM: shmobile: porter: add QSPI DT support
ARM: shmobile: porter: add VIN0/ADV7180 DT support
ARM: shmobile: porter: add I2C2 DT support
ARM: shmobile: porter: enable SATA0
ARM: shmobile: porter: add SDHI0/2 DT support
In UniPhier SoCs before ProXstream2 and PH1-LD6b, two address spaces
0x00000000 - 0x0fffffff
0x40000000 - 0x4fffffff
are both mapped to the external bus (also called system bus),
so either was OK.
In the newest two SoCs, the former (0x00000000 - 0x0fffffff) is
assigned for the serial NOR interface.
For the consistency, use the latter for all the SoCs.
Also, fix the range properties to reflect the real address mapping,
where the support card is located at the offset address 0x01f00000
of CS1 of the external bus.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Regulator fix for beagle-x15 to fix HDMI without a SD card being
inserted
- GPMC fix for showing proper timings and to allow enabling debug
options that somehow was unselectable earlier
- Add minimal documentation for new MMC1 dependency on
REGULATOR_PBIAS as it may not be obvious for people with
targeted .config files
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1+r/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Fixes for omap against v4.3-rc5" from Tony Lindgren:
- Regulator fix for beagle-x15 to fix HDMI without a SD card being
inserted
- GPMC fix for showing proper timings and to allow enabling debug
options that somehow was unselectable earlier
- Add minimal documentation for new MMC1 dependency on
REGULATOR_PBIAS as it may not be obvious for people with
targeted .config files
* tag 'omap-for-v4.3/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Documentation: ARM: List new omap MMC requirements
memory: omap-gpmc: dump "before" state before first modification
memory: omap-gpmc: Fix unselectable debug option for GPMC
ARM: dts: am57xx-beagle-x15: set VDD_SD to always-on
The IRQ signal from external devices on this board is connected to
the XIRQ4 pin of the SoC. The IRQ number should be 52, not 50.
Fixes: a5e921b477 ("ARM: dts: uniphier: add ProXstream2 and PH1-LD6b SoC/board support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for new PLL-type for stih418 A9-PLL.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The B2199 board is mounted with Realtek RTL8367 switch.
We consider the bootloader will have intiliazed the switch before jumping into
the kernel, so we declare it as a fixed link.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
These boards are mounted with Realtek RTL8367 switch.
We consider the bootloader will have intiliazed the switch before jumping into
the kernel, so we declare it as a fixed link.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This is not needed anymore. Handling a potentially pending imprecise
external abort left behind by the bootloader is now done in a slightly
safer way inside the common ARM startup code.
[gregory.clement@free-electrons.com: Beside the Armada 375 Z1 which
initially required this, is no more supported]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit enables standby support on Armada 385 DB-AP board, because
the PM initalization routine requires "marvell,armada380" compatible
string for all Armada 38x-based platforms.
Beside the compatible "marvell,armada38x" was wrong and should be fixed
in the stable kernels too.
[gregory.clement@free-electrons.com: add information, about the fixes]
Fixes: e5ee12817e ("ARM: mvebu: Add Armada 385 Access Point
Development Board support")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org>
This patch adds a label for uart0 to allow changing of uart0 pins.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The pasic3-leds driver was never in vanilla kernel. Actual configuration
data for a hypothetical driver does not describe hardware completely, so
remove them.
This patch prepare HTC Magician machine code to pasic3-leds driver
addition.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
A PXA27x SoC supports USB device mode, this patch adds support for that.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
HTC Magician contains a MAX1587A voltage regulator for a Vcore supply.
The Vcore regulation is required for a CPU speed switching. This patch adds
declaration for the max1586 driver.
Notice:
- MAX1587A version does not support the V6 (USIM) output.
- A boost resistor was directly measured for a board_id 0x3a.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch changes the comments in the HTC Magician machine source code
to better describe used devices and interfaces.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch moves platform_add_devices() (standard declaration of devices)
outside of the platform specific device declarations. Moving to the end
of the magician_init() clarifies the source code (standard and specific
declaration are not mixed).
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add a fake regulator, which is required for the correct initialization
of the PWM backlight driver.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
[ added a missing include for fixed regulator ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add a debug message for the backlight brightness function.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Magician STUART port is connected to the infraport and used by the FICP
driver. The FICP driver uses its own definition.
Required for correct initialization of the pxaficp_ir driver after
planned dmaengine conversion.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
USB host ports on the HTC Magician are wrongly enabled. Port 1 is for
bluetooth and port 2 is for OTG (mux in the charger connector).
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Old definition for the physmap-flash driver is incomplete:
- Use of an EGPIO without previous request
- Missing the MTD partitions
This patch fixes it. Read functionality was tested on the machine with
board_id 0x3a. Writing was not tested.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The pxaficp_ir driver requests a power GPIO for the transceiver internally,
so a global GPIO allocation in magician_init() is redundant.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch changes fast_mode settings for the normal and power I2C
controller on the HTC Magician machine.
Connected device on the Power I2C:
- MAX1587A: working in the fast mode
Connected devices on the Normal I2C:
- UDA1380: working in the fast mode
- OV9640: bus became stuck in the fast mode
The OV9640 is not using a standard I2C protocol, but an SCCB variant. Maybe
it is not fully compatible in the fast mode. Therefore fast mode for normal
I2C is disabled. If you not using the OV9640 then you can enable the fast
mode for the UDA1380.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
[included Philipp Zabel's comment change]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch fixes the charging detection functions for pda_power driver
(according to newly discovered EGPIOs) and add NiCd backup accumulator
charging support.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Change the default Samsung LCD refresh from an unrealistic 117Hz to 50Hz
as no video applications on the HTC Magician can work that fast.
The optimalization lowers the RAM latency at least by 3%.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch renames EGPIOs, which are used for the charging cable presence
and type detection. Old names did not correspond with an observed
functionality (on board_id 0x3a). The behavior is not:
- AC charger
- USB charger
- Cable detection
, but:
- AC/USB type
- Cable detection1
- Cable detection2
This patch fixes a possible typo in the bit offset for the cable detection
EGPIO declaration, too.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Delays for the Samsung LCD are greater than needed. These values were
extracted from a datasheet.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch renames GPIOs, which are used to control the power lines to
the LCD screen. New names correspond to a real functionality, which was
measured on the HTC Magician board_id 0x3a.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch adds EGPIO pins: Infra transceiver power, NiCD charging and
inserted charger cable.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch changes the description of the LCD power GPIO to be more
specific.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Optimize the debug messages for the LCD power.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Print more specific error message for global GPIOs.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch fixes the indentation for the HTC Magician machine definition.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
[ split pwm_remove_table() call on 2 lines ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The DTS erronously uses the wrong reg mapping and IRQ numbers for some
UART, WDT and timer nodes. Fix this.
Reported-by: John Wehle <john@feith.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SMEM is a software construct built on top of a DDR reserved region
and sometimes a device memory region called RPM message ram. Having
the RPM message ram in the smem DT node's reg property leads to the
smem node being located in different places depending on if the
message ram is being used or not. Let's add a qcom specific
property, qcom,rpm-msg-ram, and point to the device memory from
the SMEM node via a phandle. As SMEM is a software construct, it
really needs to reside at the root of the DT regardless of whether
it's using the message ram or not.
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Remove the OMAP3 core DPLL re-program code, and the associated SRAM
code that does the low-level programming of the DPLL divider, idling
of the SDRAM etc.
This code was never fully implemented in the kernel; things missing
were driver side handling of core clock changes (they need to account
for their functional clock rate being changed on-the-fly), and the whole
framework required for handling this. Thus, there is not much point
to keep carrying the low-level support code either.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the macro instead of absolute register offsets to make the code more
readable as the values now match register addresses from the datasheet.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- New board support
: add exynos5250-snow-rev5 DT file to support Snow Rev5+ board
: add exynos5422-odroidxu4 DT file to support Odroid XU4 board
: split exynos5422-odroidxu3-audio DT file from odroidxu3-common
- USE GPIO constants for flags cells for exynos boards
- fix cpu compatible value to 'arm926ej-s' for s3c2416
- add DMA support for serial ports for exynos4
- add suspend opp for exynos4412
- remove regulator-compatible usage for exynos4412-trats2
- enable EC vboot context support for Peach boards
- move display-timings node to DP for exynos5250-arndale, smdk5250 and smdk5420
- for exynos4412-odroid/odroidu3
: unify voltage regulator style and
: remove redundant pinctrl settings
: add pwm-fan node and use it as a colling device
- for exynos5422-odroidxu3
: fix power off method and LEDs
- dt-bindings
: grounded AC0KB pin on S2MPS11
: entry how to use PWM FAN as a cooling device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FqOp
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v4.4" from Kukjin Kim:
- New board support
: add exynos5250-snow-rev5 DT file to support Snow Rev5+ board
: add exynos5422-odroidxu4 DT file to support Odroid XU4 board
: split exynos5422-odroidxu3-audio DT file from odroidxu3-common
- USE GPIO constants for flags cells for exynos boards
- fix cpu compatible value to 'arm926ej-s' for s3c2416
- add DMA support for serial ports for exynos4
- add suspend opp for exynos4412
- remove regulator-compatible usage for exynos4412-trats2
- enable EC vboot context support for Peach boards
- move display-timings node to DP for exynos5250-arndale, smdk5250 and smdk5420
- for exynos4412-odroid/odroidu3
: unify voltage regulator style and
: remove redundant pinctrl settings
: add pwm-fan node and use it as a colling device
- for exynos5422-odroidxu3
: fix power off method and LEDs
- dt-bindings
: grounded AC0KB pin on S2MPS11
: entry how to use PWM FAN as a cooling device
* tag 'samsung-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (22 commits)
ARM: dts: Use GPIO constants for flags cells in exynos5440 boards
ARM: dts: Use GPIO constants for flags cells in exynos5420/5422/5800 boards
ARM: dts: Use GPIO constants for flags cells in exynos4412 boards
ARM: dts: Use GPIO constants for flags cells in exynos4120 boards
ARM: dts: Use GPIO constants for flags cells in exynos3250 boards
ARM: dts: Enable EC vboot context support on Peach boards
ARM: dts: Remove regulator-compatible usage in exynos4412-trats2
ARM: dts: Move display-timings node from fimd to dp in exynos5250-arndale, smdk5250 and smdk5420
ARM: dts: Add Exynos5250 Snow Rev5+ support on exynos5250-snow-rev5
ARM: dts: Unify voltage regulator style in exynos4412-odroid
ARM: dts: Remove redundant pinctrl settings in exynos4412-odroid
ARM: dts: Fix cpu compatible value for s3c2416
ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4
ARM: dts: Split audio configuration to separate exynos5422-odroidxu3-audio
ARM: dts: Fix power off method for exynos5422-odroidxu3-common
dt-bindings: Document grounded ACOKB pin on S2MPS11
ARM: dts: use pwm-fan device as a cooling device for exynos4412-odroidu3
ARM: dts: Add pwm-fan node for exynos4412-odroidu3
dt-bindings: Documentation entry to explain how to use PWM FAN as a cooling device
ARM: dts: add suspend opp to exynos4412
...
The DTS erronously uses the wrong reg mapping and IRQ numbers for some
UART, WDT and timer nodes. Fix this.
Reported-by: John Wehle <john@feith.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
DT patches for the 4.4 merge window, most notably:
- Enable the OTG controller on more boards
- Create new DTSI for the q8's design
- Added RSB support to the A23 and A33 SoCs
- New boards: Olimex A20 EVB, Yones bs1078v2
Plus the usual random patches enabling and / or enhancing a few things in
particular boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q2Q4
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT changes for 4.4" from Maxime Ripard:
DT patches for the 4.4 merge window, most notably:
- Enable the OTG controller on more boards
- Create new DTSI for the q8's design
- Added RSB support to the A23 and A33 SoCs
- New boards: Olimex A20 EVB, Yones bs1078v2
Plus the usual random patches enabling and / or enhancing a few things in
particular boards.
* tag 'sunxi-dt-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (59 commits)
ARM: dts: sun6i: hummingbird: Drop AXP221 DC1SW and DC5LDO supplies
ARM: dts: sun8i: sinlinx-sina33: Enable Reduced Serial Bus controller
ARM: dts: sun8i: q8-common: Enable RSB controller for A23/A33 Q8 tablets
ARM: dts: sun8i: Add Reduced Serial Bus controller device node to A23/A33 dtsi
ARM: dts: sun4i: Add AXP209 PMU regulators for pcDuino1/2
ARM: sun7i: dt: Add new Olimex A20 EVB device
ARM: dts: sun6i: hummingbird: Add aliases for rtc devices
ARM: dts: sun7i: Add dts file for Wits Pro A20 DKT
ARM: dts: sun7i: Enable USB DRC on Wexler TAB7200
ARM: dts: sun7i: Enable USB DRC on the Orange pi
ARM: dts: sun7i: Enable USB DRC on orangepi-mini
ARM: dts: axp209: Add usb_power_supply child node to the ax209 node
ARM: dts: sun8i: Make ippo-q8h-v1.2.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Add sun8i-a33-q8-tablet.dts file
ARM: dts: sun6i: Add support for Yones Toptech bs1078v2 tablets
ARM: dts: sun4i: Enable USB DRC on the Marsboard A10
ARM: dts: sun4i: gemei-g9: Add accelerometer (bma250) IRQ
ARM: dts: sun8i-a33: Add security system crypto engine clock and device nodes
ARM: dts: sun8i: Add pwm-backlight device for A23/A33 Q8 format tablets
ARM: sun8i: A23: Add missing msgbox gate
...
- use serial aliases and stdout path
- add cpufreq properties to all SoCs
- add pwm nodes for all SoCs
This depends on topic branch berlin-cpuclk-for-4.4-1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3SFe
-----END PGP SIGNATURE-----
Merge tag 'berlin-dt-for-4.4-1' of git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Merge "Marvell Berlin DT for 4.4 take 1" from Sebastian Hesselbarth:
- use serial aliases and stdout path
- add cpufreq properties to all SoCs
- add pwm nodes for all SoCs
This depends on topic branch berlin-cpuclk-for-4.4-1
* tag 'berlin-dt-for-4.4-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: berlin: add a PWM node on the BG2CD
ARM: berlin: add a PWM node on the BG2
ARM: berlin: add a PWM node on the BG2Q
ARM: berlin: dts: add the cpufreq-dt bindings on the BG2CD
ARM: berlin: dts: add the cpufreq-dt bindings on the BG2
ARM: berlin: dts: add the cpufreq-dt bindings on the BG2Q
arm: dts: berlin: use stdout-path
arm: dts: berlin: add aliases for serial
Update dts to use the new crypto driver on mvebu SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlYX5x8ACgkQCwYYjhRyO9XoUgCeOcVjHqbrmPUsxyuJt6wF8L9p
kasAn0hDt61/LCd/Tf4UJW+HzpRgoDG7
=J1D5
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.4-1' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt for 4.4 (part 1)" from Gregory CLEMENT:
Update dts to use the new crypto driver on mvebu SoCs
* tag 'mvebu-dt-4.4-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: modify Orion and Kirkwoord crypto compatible strings
ARM: mvebu: use new bindings for existing crypto devices
ARM: mvebu: define crypto SRAM ranges for all armada-38x boards
ARM: mvebu: add crypto related nodes to armada 38x dtsi
ARM: mvebu: define crypto SRAM ranges in armada-375-db.dts
ARM: mvebu: add crypto related nodes to armada 375 dtsi
ARM: mvebu: define crypto SRAM ranges for all armada-370 boards
ARM: mvebu: add crypto related nodes to armada 370 dtsi
ARM: mvebu: define crypto SRAM ranges for all armada-xp boards
ARM: mvebu: add crypto related nodes to armada-xp.dtsi
ARM: mvebu: add CPU config registers in the Armada 370/XP Device Tree
Some recently added code to avoid a bug introduced a build error
when CONFIG_PM is disabled and a macro is hidden:
arch/arm/mach-pxa/pxa3xx.c: In function 'pxa3xx_init':
arch/arm/mach-pxa/pxa3xx.c:439:3: error: 'NDCR' undeclared (first use in this function)
NDCR = (NDCR & ~NDCR_ND_ARB_EN) | NDCR_ND_ARB_CNTL;
^
This moves the macro outside of the #ifdef so it can be
referenced correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: adf3442cc8 ("ARM: pxa: fix DFI bus lockups on startup")
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
It includes a single fix for i.MX7D, which corrects the base address of
UART2 in device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWG7gvAAoJEFBXWFqHsHzOnysH/3g6f2HhjnyP627EgE8ipJJB
3S/rteN22cV0e8siM6oxa97gMjVGX9A6asGKkpE5v26SGKDbvhUhH5WCqKUioFCn
LDjcNUK1Yd830K/t7dyBM4bZlPp7nLCfLMzFG+8PvVWl5OvfR5eJ14KLAyS0mO9b
F/GoqV2VSrTw5AA3gOfBhckHtVZJJ01b4vu28G9NSc8eU4W5aJDQMDaZ40MLftuS
ZEt9o+us/YlJQzuIeKN2sk5Rb+w2jeZOXWEKOZfIFab3aE8BY+/NgedqMNwf1J1Z
EWGQ6oIOIe5vU6k9j0neQ4a5hVqW+layzgdXZaYhWzfkpM7DFuvVyeK08yiARts=
=h6oq
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "The i.MX fixes for 4.3, 2nd round:" from Shawn Guo:
It includes a single fix for i.MX7D, which corrects the base address of
UART2 in device tree.
* tag 'imx-fixes-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d: Fix UART2 base address
- BG2Q USB PHY compatible fix (also tagged for stable v4.2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BDI7
-----END PGP SIGNATURE-----
Merge tag 'berlin-fixes-for-4.3-1' of git://git.infradead.org/users/hesselba/linux-berlin into fixes
Merge "Marvell Berlin fixes for v4.3 take 1" from Sebastian Hesselbarth:
- BG2Q USB PHY compatible fix (also tagged for stable v4.2)
* tag 'berlin-fixes-for-4.3-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: change BG2Q's USB PHY compatible
Move the code out from arch/arm/common and merge it inside of the dmaengine
driver.
This change is done with as minimal (if eny) functional change to the code
as possible to avoid introducing regression.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The upcoming change to merge the arch/arm/common/edma.c into
drivers/dma/edma.c will need this change when booting daVinci devices in
no DT mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Convert the eDMA platform device creation to use
struct platform_device_info XXXXXX __initconst and
platform_device_register_full()
This will allow us to cleanly specify the dma_mask for the devices in an
upcoming patch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the driver stack no longer depends on lookup with id number in a
global array of pointers, the limitation for the number of eDMAs are no
longer needed. We can handle as many eDMAs in legacy and DT boot as we have
memory for them to allocate the needed structures.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of relying on indexes pointing to edma private date in the global
pointer array, pass the private data pointer via the public API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Merge the iomem into the 'struct edma' and change the internal (static)
functions to use pointer to the edma_cc instead of the ctlr number.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the of_dma_controller is registered in the non dmaengine driver we could
have race condition:
the of_dma_controller has been registered, but the dmaengine driver is not
yet probed. Drivers requesting DMA channels during this window will fail
since we do not yet have dmaengine drivers registered.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently we have one device created to handle all (maximum 2) eDMAs in the
system.
With this change all eDMA instance will have it's own device/driver.
This change is needed for further cleanups in the eDMA driver stack since
the one device/driver to handle all eDMAs in the system was not flexible
enough and prevents the upcoming work.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We no longer have users for these functions so they can be removed.
Remove also unused enums from the header file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case when the interrupt happened for the second eDMA the channel
number was incorrectly passed to the client driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
New bindings and driver have been created for STM32 series parts. This
patch integrates this changes.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for booting secondary CPUs on mt6589, mt8127
and mt8135.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We enable GTP6 which ungates the arch timer clock.
In the future this should be done in the bootloader.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Replace "disable" by "disabled" in the Qualcomm MSM8974 dtsi
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
clock controller nodes which also support power domains (gdscs') need
to have a #power-domain-cells property. Add these for gcc and mmcc
nodes of msm8974, gcc of apq8084 and msm8916.
Also update gcc and mmcc bindings for it.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds notify led support on IFC6410, whose trigger can be
configured from userspace.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add pwrseq support to sdcc4 which would enable a proper reset of WLAN
without ugly hacks in the board support file.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds pwrseq for WLAN which resets the WLAN just before the
SDIO bus is up.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds missing 2pin uart pinctrl property to gsbi7 uart on
CM-QS600.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds missing gsbi7 uart pinctrl, this is the default debug
uart on most boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Usage of generic names like "uart_pins" is confusing to the reader, given
the fact that there could be more than one uart on APQ8064.
This patch adds gsbi prefix to uart pinctrl nodes so as to avoid such
confusion.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds support to pm8921 power button.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds rtc node for pmic8921.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch removes unnecessary eeprom label, which is not used
anywhere in the board file.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch removes unnecessary eeprom label, which is not used
anywhere in the board file.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch removes i2c pinctrl properties from board which which are now
mentioned in the SOC specific file. This will avoid redundant properties
across multiple board fiiles.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This doesn't match the binding, and the driver doesn't look to
be using it. Remove the extra element.
CC: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add low priority accumulator channel that can monitor multiple QMSS
queues. User for example could use the accumular queue for Netcp
Rx completion. While at it, also add an extra line end of each top
level node in DTS to make it more readable.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Enable fpga manager framework and low level driver for
socfpga in socfpga_defconfig
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The DC5LDO regulator supplies VDD-CPUS, which is for the embedded
controller in the A31 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have axp22x.dtsi describing common axp22x hardware, use
it and reference the nodes instead of declaring the whole tree.
Also drop the "always-on" from the vdd-gpu regulator, since we don't
support the GPU anyway.
And add a regulator reference for cpu0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The power configuration on this board is the same as the pcDuino v3.
This will enable frequency/voltage scaling over the standard A20
operating points from 144 MHz to 960 MHz.
Tested using cpufreq-ljt-stress-test on two pcDuino v3 Nano boards; also
tested successfully with voltages reduced by 0.025 V.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We've everything we need to support the gmac on Colombus, turn it on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A33 Q8 tablets with the et-q8-v1.6 pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the et-q8-v1.6.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A23 Q8 tablets with the ippo-q8h-v* pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the ippo-q8h-v*.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a generic dts file for A23 based q8 formfactor tablets,
this is intended to replace both sun8i-a23-ippo-q8h-v5.dts and
sun8i-a23-ippo-q8h-v1.2.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since we now have a generic data structure to express an
interrupt specifier, convert all hierarchical irqchips that
are OF based to use a fwnode_handle as part of their alloc
and xlate (which becomes translate) callbacks.
As most of these drivers have dependencies (they exchange IRQ
specifiers), change them all in a single, massive patch...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The struct irq_domain contains a "struct device_node *" field
(of_node) that is almost the only link between the irqdomain
and the device tree infrastructure.
In order to prepare for the removal of that field, convert all
users to use irq_domain_get_of_node() instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This enables the SPDIF optical audio output on the Radxa Rock
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Actviate HDMI output of the RCar DU (and LVDS while we are here).
Enable the HDMI encoder chip found on Lager/Koelsch boards.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached
to them and also enable USB PHY device for the Porter board. We have to
enable everything in one patch since EHCI/OHCI devices are already linked
to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In DRA74x, DRA72x and AM57xx EVMs the card detect gpio is
designed as active low gpio. So correcting the dt card detect
gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM43xx the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
uart2 pinmux is already defined in omap3-igep0020-common.dtsi, remove
the duplicate node.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use tabs instead of spaces for indentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The card detect GPIO is using IRQ_TYPE_LEVEL_LOW in the GPIO flag cells
but this defined constant is meant to be used for a IRQ and not a GPIO.
So instead use GPIO_ACTIVE_LOW that seems to be the original intention.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LDO1 regulator (VDD_SD) is connected to SoC's vddshv8. vddshv8 needs to
be kept always powered (see commit 5a0f93c657 ("ARM: dts: Add
am57xx-beagle-x15"), but at the moment VDD_SD is enabled/disabled
depending on whether an SD card is inserted or not.
This patch sets LDO1 regulator to always-on.
This patch has a side effect of fixing another issue, HDMI DDC not
working when SD card is not inserted:
Why this happens is that the tpd12s015 (HDMI level shifter/ESD
protection chip) has LS_OE GPIO input, which needs to be enabled for the
HDMI DDC to work. LS_OE comes from gpio6_28. The pin that provides
gpio6_28 is powered by vddshv8, and vddshv8 comes from VDD_SD.
So when SD card is not inserted, VDD_SD is disabled, and LS_OE stays
off.
The proper fix for the HDMI DDC issue would be to maybe have the pinctrl
framework manage the pin specific power.
Apparently this fixes also a third issue (copy paste from Kishon's
patch):
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Louis McCarthy <compeoree@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA74x family of SoCs have a second DSP, that also has
two MMUs just like the DSP1 subsystem. Add the IOMMU nodes
for this DSP2 subsystem in disabled state to the DRA74x
specific DTS file, the nodes would need to be enabled
appropriately in the respective board DTS files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA7xx family of SOCs have two IPUs and one DSP processor
subsystems in common. The IOMMU DT nodes have been added for
these processor subsystems, and have been disabled by default.
These MMUs are very similar to those on OMAP4 and OMAP5, with
the only difference being the presence of a second MMU within
the DSP subsystem for the EDMA port. The DSP IOMMUs also need
an additional 'ti,syscon-mmuconfig' property compared to the
IPU IOMMUs.
NOTE: The enabling of these nodes is left to the respective
board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP_SYSTEM sub-module is a dedicated system control logic
module present within a DRA7 DSP processor sub-system. This
module is responsible for power management, clock generation
and connection to the device PRCM module.
Add a syscon node for this module for the DSP2 processor
sub-system. This is added as a syscon node as it is a common
configuration module that can be used by the different IOMMU
instances and the corresponding remoteproc device.
The node is added to the dra74x.dtsi file, as the DSP2 processor
subsystem is usually present only on the DRA74x variants of the
DRA7 SoC family.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP_SYSTEM sub-module is a dedicated system control logic
module present within a DRA7 DSP processor sub-system. This
module is responsible for power management, clock generation
and connection to the device PRCM module.
Add a syscon node for this module for the DSP1 processor
sub-system. This is added as a syscon node as it is a common
configuration module that can be used by the different IOMMU
instances and the corresponding remoteproc device.
The node is added to the common dra7.dtsi file, as the DSP1
processor sub-system is mostly common across all the variants
of the DRA7 SoC family.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Many OMAP2+ DTS are not using the defined constants to express
the GPIO polarity. Replace these so the DTS are easier to read.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).
This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]
http://beagleboard.org/greenhttp://www.seeedstudio.com/wiki/Beaglebone_green
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding child
sub-mailbox (IPC 3.x) nodes for the Beagle X15 EVM boards. This
is needed to enable communication with the respective remote
processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the DRA72 EVM board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, and DSP1 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the DRA7 EVM board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the sub-mailbox nodes that are used to communicate between
MPU and the remote processors IPU1, IPU2 and DSP1. These match the
respective node definitions on DRA74x to maintain compatibility for
the equivalent remote processors. There is no DSP2 on DRA72x, and
so the corresponding sub-mailbox node is not added.
These sub-mailbox nodes are added to match the hard-coded mailbox
configuration used within the TI IPC 3.x software package. The
Dual-Cortex M4 IPU1 and IPU2 processor sub-systems are assumed to
be running in SMP-mode, and hence only a single sub-mailbox node
is added for each.
All these sub-mailbox nodes are left in disabled state, and should
be enabled (and modified if needed) as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the sub-mailbox nodes that are used to communicate between
MPU and the remote processors IPU1, IPU2, DSP1 and DSP2.
The sub-mailbox nodes utilize the System Mailbox instances 5 and 6.
These sub-mailbox nodes are added to match the hard-coded mailbox
configuration used within the TI IPC 3.x software package. The
Dual-Cortex M4 IPU1 and IPU2 processor sub-systems are assumed to
be running in SMP-mode, and hence only a single sub-mailbox node
is added for each.
All these sub-mailbox nodes are left in disabled state, and should
be enabled (and modified if needed) as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleaned up the regulators on the wega board. Created a simple bus,
renamed the regulators according to the schematics and added missing
regulator on wega.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra7-evm has 2 gpio keys wired through TS_LCD_GPIO3, TS_LCD_GPIO4
which in turn connected to PCF8575 GPIO pcf_lcd: gpio@20 expander
pins 2 and 3.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra7-evm has 4 user gpio leds connected to PCF8575 GPIO pcf_lcd:
gpio@20 expander pins [4,5,6,7], so add corresponding DT nodes.
Do not enable any triggers by default as not all of them are proved
to work on -RT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds DT definition for CF8575 GPIO pcf_lcd: gpio@20
expander which is connected to i2c bus 1 and has slave address 0x20.
It allows to control:
- tc_lcd gpios, pins p0-p3
- user leds, pins p4-p7
- control LCD panel power, p15
PCF8575 GPIO pcf_lcd: gpio@20 expander supports interrupt controller
functionality and its INT line is connected to dra7 GPIO6.11 pin.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The analog audio setup consists of:
McASP3 <-> tlv320aic3104 codec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DVDD is supplied via TPS77018DBVT fixed regulator from vdd_3v3
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses tlv320aic3106 codec connected to McASP3. The master clock
for the codec and McASP3 is coming from ATL2.
McASP3 is the master on the I2S bus.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO expander's p1 on i2c5 bus 0x26 address is used for selecting
between audio and VIN6 functionality. For VIN6 use an add on card is
needed while audio is present on the board itself.
Select the audio functionality over the VIN6 in the dts file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DVDD is supplied via TPS77018DBVT fixed regulator from evm_3v3
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses tlv320aic3106 codec connected to McASP3. The master clock
for the codec and McASP3 is coming from ATL2.
McASP3 is the master on the I2S bus.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This GPIO expander is used for controlling various muxes on the board.
By default select audio functionality over VIN6 by setting the P1
(vin6_sel_s0) pin to low.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TPS77018DBVT is used to create 1.8V from avm_3v3_sw's 3.3V connected to
aic3106's DVDD.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the name for the supply as it is in the schematics since the same
supply is used for other peripherals than MMC2, like audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
