Fixes the clock-gating issue when pipe scaling is enabled.
(Lineage #2006604312)
V2: Fix typo in headline(Chris)
Handle the non double buffered nature of the register(Ville)
V3: Fix checkpatch warning. BAT failure for V2 on gen3 looks unrelated.
V4: Split the icl and skl wa's(Ville)
V5: Split the checks for icl and skl(Ville)
V6: Correct the flipped checks in intel_pre_plane_update(Ville)
V7: Use enum for pipe and extend the WA for plane scalers(Ville)
V8: Eliminate the redundant use of pch_pfit(Ville)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190417185901.14833-1-radhakrishna.sripada@intel.com
The spec has changed since skl_max_plane_width() was written.
Now the SKL limits are lower than what they were initially, and
GLK and ICL have different limits. Update the code to match the
spec.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190418195907.23912-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Fix the order of lane, port parameters passed to the register macro.
Note that this was already partly fixed by commit
37fc7845df ("drm/i915: Call MG_DP_MODE() macro with the right parameters order")
While at it simplify things by using the macro directly instead of an
unnecessary redirection via an array.
v2:
- Add a note the commit message about simplifying things. (José)
Fixes: 58106b7d81 ("drm/i915: Make MG PHY macros semantically consistent")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419071026.32370-1-imre.deak@intel.com
Add CONFIG_DRM_MSM_GPU_STATE to conditionally compile Adreno GPU state
code depending on the availability of the dependencies.
Reported-by: Hulk Robot <hulkci@huawei.com>
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 1707add815 ("drm/msm/a6xx: Add a6xx gpu state")
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Describe the zap-shader node that defines a reserved memory region
to store the zap shader.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The a6xx GPU powers on in secure mode which restricts what memory it can
write to. To get out of secure mode the GPU driver can write to
REG_A6XX_RBBM_SECVID_TRUST_CNTL but on targets that are "secure" that
register region is blocked and writes will cause the system to go down.
For those targets we need to execute a special sequence that involves
loadinga special shader that clears the GPU registers and use a PM4
sequence to pull the GPU out of secure. Add support for loading the zap
shader and executing the secure sequence. For targets that do not support
SCM or the specific SCM sequence this should fail and we would fall back
to writing the register.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
a5xx and a6xx both share (mostly) the same code to load the zap shader and
bring the GPU out of secure mode. Move the formerly 5xx specific code to
adreno to make it available for a6xx too.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add documentation for the interconnect and interconnect-names bindings
for the GPU node as detailed by bindings/interconnect/interconnect.txt.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
When we are called to relieve mempressue via the shrinker, the only way
we can make progress is either by discarding unwanted pages (those
objects that userspace has marked MADV_DONTNEED) or by reclaiming the
dirty objects via swap. As we know that is the only way to make further
progress, we can initiate the writeback as we invalidate the objects.
This means the objects we put onto the inactive anon lru list are
already marked for reclaim+writeback and so will trigger a wait upon the
writeback inside direct reclaim, greatly improving the success rate of
direct reclaim on i915 objects.
The corollary is that we may start a slow swap on opportunistic
mempressure from the likes of the compaction + migration kthreads. This
is limited by those threads only being allowed to shrink idle pages, but
also that if we reactivate the page before it is swapped out by gpu
activity, we only page the cost of repinning the page. The cost is most
felt when an object is reused after mempressure, which hopefully
excludes the latency sensitive tasks (as we are just extending the
impact of swap thrashing to them).
Apparently this is not the first time we've had this idea. Back in
commit 5537252b6b ("drm/i915: Invalidate our pages under memory
pressure") we wanted to start writeback but settled on invalidate after
Hugh Dickins warned us about a possibility of a deadlock within shmemfs
if we started writeback from shrink_slab. Looking at the callchain,
using writeback from i915_gem_shrink should be equivalent to the pageout
also employed by shrink_slab, i.e. it should not be any riskier afaict.
v2: Leave mmapings intact. At this point, the only mmapings of our
objects will be via CPU mmaps on the shmemfs filp, which are
out-of-scope for our LRU tracking. Instead leave those pages to the
inactive anon LRU page list for aging and pageout as normal.
v3: Be selective on which paths trigger writeback, in particular
excluding paths shrinking just to reclaim vm space (e.g. mmap, vmap
reapers) and avoid starting writeback on the entire process space from
within the pm freezer.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108686
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Michal Hocko <mhocko@suse.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20190420115539.29081-1-chris@chris-wilson.co.uk
GPU reset is now available with GuC enabled, so re-enable our check that
this reset is usable from atomic context.
Signed-off-by: Fernando Pacheco <fernando.pacheco@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419230015.18121-6-fernando.pacheco@intel.com
We have now prepared the guc reset paths to avoid taking struct_mutex, or
any other lock, and so it is now safe to re-enable.
References: fe62365f9f ("drm/i915/guc: Disable global reset")
Signed-off-by: Fernando Pacheco <fernando.pacheco@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419230015.18121-5-fernando.pacheco@intel.com
Currently we pin the GuC or HuC firmware image just before uploading.
Perma-pin during uC initialization instead and use the range reserved at
the top of the address space.
Moving the firmware resulted in needing to:
- use an additional pinning for the rsa signature which will be used
during HuC auth as addresses above GUC_GGTT_TOP do not map through GTT.
v2: Remove call to set to gtt domain
Do not restore fw gtt mapping unconditionally
Separate out pin/unpin functions and drop usage of pin/unpin
Use uc_fw init/fini functions to bind/unbind fw object
v3: Bind is only needed during xfer (Chris)
Remove attempts to bind outside of xfer (Chris)
Mark fw bind/unbind static
Signed-off-by: Fernando Pacheco <fernando.pacheco@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419230015.18121-4-fernando.pacheco@intel.com
GuC and HuC depend on struct_mutex for device reinitialization. Moving
away from this dependency requires perma-pinning the firmware images in
GGTT. The upper portion of the GuC address space has a sizeable hole
(several MB) that is inaccessible by GuC. Reserve this range within GGTT
as it can comfortably hold GuC/HuC firmware images.
v2: Reserve node rather than insert (Chris)
Simpler determination of node start/size (Daniele)
Move reserve/release out to intel_guc.* files
v3: Reserve starting at GUC_GGTT_TOP only and bail if this
fails (Chris)
Signed-off-by: Fernando Pacheco <fernando.pacheco@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419230015.18121-3-fernando.pacheco@intel.com
he uC firmware init function is called during GuC/HuC init early phases.
Rename to include "_early" and properly reflect which phase we are at.
The uC firmware fini function is cleaning up the state set/created on
firmware fetch. Replace "_fini" with "_cleanup_fetch".
v2: also rename uC fw fini function
Signed-off-by: Fernando Pacheco <fernando.pacheco@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419230015.18121-2-fernando.pacheco@intel.com
If we know that the user cannot access the GGTT, by virtue of having a
segregated memory area, we can skip clearing the unused entries as they
cannot be accessed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419201207.5477-1-chris@chris-wilson.co.uk
This is to work around problems with libva and vainfo.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190417112525.16848-1-christian.koenig@amd.com
An interesting discussion regarding "hybrid interrupt polling" for NVMe
came to the conclusion that the ideal busyspin before sleeping was half
of the expected request latency (and better if it was already halfway
through that request). This suggested that we too should look again at
our tradeoff between spinning and waiting. Currently, our spin simply
tries to hide the cost of enabling the interrupt, which is good to avoid
penalising nop requests (i.e. test throughput) and not much else.
Studying real world workloads suggests that a spin of upto 500us can
dramatically boost performance, but the suggestion is that this is not
from avoiding interrupt latency per-se, but from secondary effects of
sleeping such as allowing the CPU reduce cstate and context switch away.
In a truly hybrid interrupt polling scheme, we would aim to sleep until
just before the request completed and then wake up in advance of the
interrupt and do a quick poll to handle completion. This is tricky for
ourselves at the moment as we are not recording request times, and since
we allow preemption, our requests are not on as a nicely ordered
timeline as IO. However, the idea is interesting, for it will certainly
help us decide when busyspinning is worthwhile.
v2: Expose the spin setting via Kconfig options for easier adjustment
and testing.
v3: Don't get caught sneaking in a change to the busyspin parameters.
v4: Explain more about the "hybrid interrupt polling" scheme that we
want to migrate towards.
Suggested-by: Sagar Kamble <sagar.a.kamble@intel.com>
References: http://events.linuxfoundation.org/sites/events/files/slides/lemoal-nvme-polling-vault-2017-final_0.pdf
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419182625.11186-1-chris@chris-wilson.co.uk
First loop does copy_from_user() without the table lock held and
just stores the handle. Second loop looks up buffer objects with the
table_lock held without potentially blocking or faulting. This lets us
clean up a bunch of custom, non-faulting copy_from_user() code.
Signed-off-by: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that we don't have the mmap_sem lock inversion, we don't need to
jump through this particular hoop anymore.
Signed-off-by: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We use a llist and a worker to delay the object cleanup. This avoids
taking mmap_sem and struct_mutex in the wrong order when calling
drm_gem_object_put_unlocked() from drm_gem_mmap().
Fixes lockdep problem with copy_from_user() in msm_ioctl_gem_submit().
Signed-off-by: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The HFI tasklet was removed in df0dff1 ("drm/msm/a6xx: Poll for HFI
responses") but the tasklet_struct was accidentally left behind.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently if the GMU resume function fails all we try to do is clear the
BOOT_SLUMBER oob which usually times out and ends up in a cycle of death.
If the resume function fails at any point remove any RPMh votes that might
have been added and try to shut down the GMU hardware cleanly.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that the GX domain is sorted we can wire up a working GMU reset.
IF a GMU hang was detected then try to forcefully shut down the GMU
in the power down sequence which should ensure that it can recover
normally on the next power up.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
99.999% of the time during normal operation the GMU is responsible
for power and clock control on the GX domain and the CPU remains
blissfully unaware. However, there is one situation where the CPU
needs to get involved:
The power sequencing rules dictate that the GX needs to be turned
off before the CX so that the CX can be turned on before the GX
during power up. During normal operation when the CPU is taking
down the CX domain a stop command is sent to the GMU which turns
off the GX domain and then the CPU handles the CX domain.
But if the GMU happened to be unresponsive while the GX domain was
left then the CPU will need to step in and turn off the GX domain
before resetting the CX and rebooting the GMU. This unfortunately
means that the CPU needs to be marginally aware of the GX domain
even though it is expected to usually keep its hands off.
To support this we create a semi-disabled GX power domain that
does nothing to the hardware on power up but tries to shut it
down normally on power down. In this method the reference counting
is correct and we can step in with the pm_runtime_put() at the right
time during the failure path.
This patch sets up the connection to the GX power domain and does
the magic to "enable" and disable it at the right points.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The GMU should have two power domains defined: "cx" and "gx". "cx" is the
actual power domain for the device and "gx" will be attached at runtime
to manage reference counting on the GPU device in case of a GMU crash.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The GMU code currently has some misguided code to try to work around
a hardware quirk that requires the power domains on the GPU be
collapsed in a certain order. Upcoming patches will do this the
right way so get rid of the unused and unwanted regulator
code.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the capability to query information from a submit queue.
The first available parameter is for querying the number of GPU faults
(hangs) that can be attributed to the queue.
This is useful for implementing context robustness. A user context can
regularly query the number of faults to see if it is responsible for any
and if so it can invalidate itself.
This is also helpful for testing by confirming to the user driver if a
particular command stream caused a fault (or not as the case may be).
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
For KHR_robustness, userspace wants to know two things, the count of GPU
faults globally, and the count of faults attributed to a given context.
This patch providees the former, and the next patch provides the latter.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
For now it always returns '0' (false), but once the iommu work is in
place to enable per-process pagetables we can update the value returned.
Userspace needs to know this to make an informed decision about exposing
KHR_robustness.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
For consistency (and elegance!), add intel_device_info.has_rps.
The immediate boon is that RPS support is now emitted along the other
capabilities in the debug log and after errors.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419134836.5626-1-chris@chris-wilson.co.uk
The driver does not currently support unbinding from a device which is
in use. Since open file descriptors may still be pointing into kernel
memory where the device structures used to be, entirely correct kernel
panics protect the driver from being unbound as we should not be
unbinding it before those dangling pointers have been made safe.
According to the documentation found inside drivers/gpu/drm/drm_drv.c,
drm_dev_unplug() should be used instead of drm_dev_unregister() in
order to make a device inaccessible to users as soon as it is unpluged.
Follow that advice to make those possibly dangling pointers safe,
protected by DRM layer from a user who is otherwise left pointing into
possibly reused kernel memory after the driver has been unbound from
the device. Once done, also cancel inflight operations immediately by
calling i915_gem_set_wedged().
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405130235.7707-2-janusz.krzysztofik@linux.intel.com
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:57:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 47, but without a corresponding object release within this function.
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:66:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 47, but without a corresponding object release within this function.
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:118:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 47, but without a corresponding object release within this function.
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:57:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 51, but without a corresponding object release within this function.
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:66:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 51, but without a corresponding object release within this function.
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:118:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 51, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Mamta Shukla <mamtashukla555@gmail.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Sharat Masetty <smasetty@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org (open list)
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The patch ("OPP: Add support for parsing the 'opp-level' property")
adds an API enabling a cleaner way to read the opp-level. Let's use
the new API.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Iterate and assign HW intf block to physical encoders
in encoder modeset. Moving all the HW block assignments
to encoder modeset to allow easy switching to state
based resource management.
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1550107156-17625-7-git-send-email-jsanka@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
After resource allocation, iterate and populate mixer/ctl
hw blocks in encoder modeset thereby centralizing all
the resource mapping to the CRTC. This change is made
for easy switching to state based allocation using
private objects later in this series.
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1550107156-17625-6-git-send-email-jsanka@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
release resources allocated in mode_set if any of
the hw check fails. Most of these checks are not
necessary and they will be removed in the follow up
patches with state based resource allocations.
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1550107156-17625-4-git-send-email-jsanka@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Both video and command physical encoders will have
a hw interface assigned to it. So there is really no
need to track the hw block in specific encoder subclass.
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1550107156-17625-2-git-send-email-jsanka@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The frame_busy mask is used in frame_done event handling, which is not
invoked for async commits. So an async commit will leave the
frame_busy mask populated after it completes and future commits will start
with the busy mask incorrect.
This showed up on disable after cursor move. I was hitting the "this should
not happen" comment in the frame event worker since frame_busy was set,
we queued the event, but there were no frames pending (since async
also doesn't set that).
Reviewed-by: Fritz Koenig <frkoenig@google.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190130163220.138637-1-sean@poorly.run
Signed-off-by: Rob Clark <robdclark@chromium.org>
In the case of an async/cursor update, we don't wait for the frame_done
event, which means handle_frame_done is never called, and the frame_done
watchdog isn't canceled. Currently, this results in a frame_done timeout
every time the cursor moves without a synchronous frame following it up
before the timeout expires. Since we don't wait for frame_done, and
don't handle it, we shouldn't modify the watchdog.
Reviewed-by: Fritz Koenig <frkoenig@google.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128204306.95076-4-sean@poorly.run
Signed-off-by: Rob Clark <robdclark@chromium.org>
There exists a bunch of confusion as to what the actual units of
frame_done is:
- The definition states it's in # of frames
- CRTC treats it like it's ms
- frame_done_timeout comment thinks it's Hz, but it stores ms
- frame_done timer is setup such that it _should_ be in frames, but the
timeout is super long
So this patch tries to interpret what the driver really wants. I've
de-centralized the #define since the consumers are expecting different
units.
For crtc, we just use 60ms since that's what it was doing before.
Perhaps we could get fancy and scale with vrefresh, but that's for
another time.
For encoder, fix the comments and rename frame_done_timeout so it's
obvious what the units are. In practice, frame_done_timeout is really
just checked against 0 || !0, which I guess is why the units being wrong
didn't matter. I've also dropped the timeout from the previous 60 frames
to 5. That seems like more than enough time to give up on a frame, and
my guess is that no one intended for the timeout to _actually_ be 60
frames.
Reviewed-by: Fritz Koenig <frkoenig@google.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128204306.95076-3-sean@poorly.run
Signed-off-by: Rob Clark <robdclark@chromium.org>
Instead of setting the timeout and then immediately reading it back
(along with the hand-rolled msecs_to_jiffies calculation), just
calculate it once and set it in both places at the same time.
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128204306.95076-2-sean@poorly.run
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently the IOMMU code calls pm_runtime_get/put on the GPU or display
device before doing a IOMMU operation. This was because usually the
IOMMU driver didn't do power control of its own and since the hardware
used the same clocks and power as the respective multimedia device it
was a easy way to make sure that the power was available.
Now two things have changed. First, the SMMU devices can do their own power
control and more important bringing up the a6xx GPU isn't as easy as
turning on some clocks. To bring the GPU up we need the GMU which itself
needs the IOMMU so we have a chicken and egg problem.
Luckily this is easily fixed by removing the pm_runtime calls from the
functions and letting the device link to the IOMMU device handle the magic.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The pages backing the GEM objects are kept pinned in place as
long as they are alive, so they must not be allocated from the
MOVABLE zone. Blocking page migration for too long will cause
the VM subsystem headaches and will outright break CMA, as a
few pinned pages in CMA will lead to failure to find the
required large contiguous regions.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
