From the 3 WAs for PSR2 man track/selective fetch this is only one
needed when doing single full frames at every flip.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200810174144.76761-2-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
All GEN12 platforms supports PSR2 selective fetch but not all GEN12
platforms supports PSR2 hardware tracking(aka RKL).
This feature consists in software programming registers with the
damaged area of each plane this way hardware will only fetch from
memory those areas and sent the PSR2 selective update blocks to panel,
saving even more power.
But as initial step it is only enabling the full frame fetch at
every flip, the actual selective fetch part will come in a future
patch.
Also this is only handling the page flip side, it is still completely
missing frontbuffer modifications, that is why the
enable_psr2_sel_fetch parameter was added.
v3:
- calling intel_psr2_sel_fetch_update() during the atomic check phase
(Ville)
BSpec: 55229
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200810174144.76761-1-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We usually assume that increasing PCI device revision ID's translates to
newer steppings; macros like IS_KBL_REVID() that we use rely on this
behavior. Unfortunately this turns out to not be true on KBL; the
newer device 2 revision ID's sometimes go backward to older steppings.
The situation is further complicated by different GT and display
steppings associated with each revision ID.
Let's work around this by providing a table to map the revision ID to
specific GT and display steppings, and then perform our comparisons on
the mapped values.
v2:
- Move the kbl_revids[] array to intel_workarounds.c to avoid compiler
warnings about an unused variable in files that don't call the
macros (kernel test robot).
Bspec: 18329
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200811032105.2819370-1-matthew.d.roper@intel.com
Reviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This new HBR2 table for TGL-U and TGL-Y is required to pass
DisplayPort compliance.
BSpec: 49291
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200807192629.64134-2-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There is no way to differentiate TGL-U from TGL-Y by the PCI ids as
some ids are available in both SKUs.
So here using the root device id in the PCI bus that iGPU is in
to differentiate between U and Y.
BSpec: 44455
Reviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200807192629.64134-1-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The command register is the PCODE MBOX low register not the high one as
described by the spec. This left the system with the TC-cold power state
being blocked all the time. Fix things by using the correct register.
Also to make sure we retry a request for at least 600usec, when the
PCODE MBOX command itself succeeded, but the TC-cold block command
failed, sleep for 1msec unconditionally after any fail.
The change was tested with JTAG register read of the HW/FW's actual
TC-cold state, which reported the expected states after this change.
Tested-by: Nivedita Swaminathan <nivedita.swaminathan@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805150056.24248-1-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The dependency between power wells is determined by the ordering of the
power well list: when enabling the power wells for a domain, this
happens walking the power well list forward, while disabling them
happens in the reverse direction. Accordingly a power well on the list
must follow any other power well it depends on.
Since the TC AUX power wells depend on TC-cold being blocked, move the
TC-cold off power well before all AUX power wells.
Fixes: 3c02934b24 ("drm/i915/tc/tgl: Implement TC cold sequences")
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720232952.16228-1-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
igt_mm_config() calls ilog2() on the (pseudo)random 21-bit number
s>>12. Once in 2 million seeds, this is zero and ilog2 summons
the nasal demons.
There was an attempt to handle this case with a max(), but that's
too late; ms could already be something bizarre.
Given that the low 12 bits of s and ms are always zero, it's a lot
simpler just to divide them by 4096, then everything fits into 32
bits, and we can easily generate a random number 1 <= s <= 0x1fffff.
Fixes: 14d1b9a624 ("drm/i915: buddy allocator")
Signed-off-by: George Spelvin <lkml@sdf.org>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325192429.GA8865@SDF.ORG
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Introduces a new parameters to execbuf so that we can specify syncobj
handles as well as timeline points.
v2: Reuse i915_user_extension_fn
v3: Check that the chained extension is only present once (Chris)
v4: Check that dma_fence_chain_find_seqno returns a non NULL fence (Lionel)
v5: Use BIT_ULL (Chris)
v6: Fix issue with already signaled timeline points,
dma_fence_chain_find_seqno() setting fence to NULL (Chris)
v7: Report ENOENT with invalid syncobj handle (Lionel)
v8: Check for out of order timeline point insertion (Chris)
v9: After explanations on
https://lists.freedesktop.org/archives/dri-devel/2019-August/229287.html
drop the ordering check from v8 (Lionel)
v10: Set first extension enum item to 1 (Jason)
v11: Rebase
v12: Allow multiple extension nodes of timeline syncobj (Chris)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Co-authored-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v11)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200804085954.350343-3-lionel.g.landwerlin@intel.com
Link: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/2901
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We're planning to use this for a couple of new feature where we need
to provide additional parameters to execbuf.
v2: Check for invalid flags in execbuffer2 (Lionel)
v3: Rename I915_EXEC_EXT -> I915_EXEC_USE_EXTENSIONS (Chris)
v4: Rebase
Move array fence parsing in i915_gem_do_execbuffer()
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200804085954.350343-2-lionel.g.landwerlin@intel.com
Link: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/2901
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The hardware team has dropped this workaround from the bspec; it is no
longer needed.
This reverts commit 111822b21be995a3a4a731066db3d820523c57f7.
Bspec: 49291
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200804044024.1931170-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In the case of calling check_digital_port_conflicts() failed, a
negative error code -EINVAL should be returned.
Fixes: bf5da83e4b ("drm/i915: Move check_digital_port_conflicts() earier")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200802111535.5200-1-tianjia.zhang@linux.alibaba.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In function i915_active_acquire_preallocate_barrier(), not all
paths have the return value set correctly, and in case of memory
allocation failure, a negative error code should be returned.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200802115655.25568-1-chris@chris-wilson.co.uk
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
A recent bspec update removed the LPDDR4 single channel entry from the
buddy register table, but added a new four-channel entry.
Workaround 1409767108 hasn't been updated with any guidance for four
channel configurations, so we leave that alternate table unchanged for
now.
Bspec 49218
Fixes: 3fa01d642f ("drm/i915/tgl: Program BW_BUDDY registers during display init")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612204734.3674650-1-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We use i915_active_fini() as a debug check on the i915_active state
before freeing. If we forget to call it, we may end up angering the
debugobjects contained within.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200731085015.32368-1-chris@chris-wilson.co.uk
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
It's been a while since gen6_rps_boost() [that only worked on gen6+] was
replaced by intel_rps_boost() that understood itself when rps was
active. Since the intel_rps_boost() is gen-agnostic, just call it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728152219.1387-1-chris@chris-wilson.co.uk
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since we want to read the values from the HWSP as written to by the GPU,
warn the compiler that the values are volatile.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728152110.830-2-chris@chris-wilson.co.uk
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since we use the module parameters stored inside the drm_i915_device
itself, we need to ensure the mock i915_device also sets up the right
defaults.
Fixes: 8a25c4be58 ("drm/i915/params: switch to device specific parameters")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728150600.4509-1-chris@chris-wilson.co.uk
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fbc is causing random underruns in CI execution on TGL platforms.
Disabling the same while the problem is being debugged and analyzed.
v2: Moved the check below the module param check (Ville)
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716145857.6911-1-uma.shankar@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Although the WA description targets the platforms it is a workaround
for the affected PCHs, that is why it is being checked.
v2: excluding DG1 fake PCH from WA
BSpec: 52890
BSpec: 53273
BSpec: 52888
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727164729.28836-1-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
After doing normal PHY-B initialization on Rocket Lake, we need to
manually copy some additional PHY-A register values into PHY-B
registers.
Note that the bspec's combo phy page doesn't specify that this
workaround is restricted to specific platform steppings (and doesn't
even do a very good job of specifying that RKL is the only platform this
is needed on), but the RKL workaround page lists this as relevant only
for A and B steppings, so I'm trusting that information for now.
v2: Make rkl_combo_phy_b_init_wa() static
v3:
- Minimize variables in WA function. (Jose)
- Fix timeout duration (usec vs msec). (Jose)
- Add verification of workaround. (Jose)
- Fix stepping bounds in comment.
Bspec: 49291
Bspec: 53273
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-6-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If HTI (also sometimes called HDPORT) is enabled at startup, it may be
using some of the PHYs and DPLLs making them unavailable for general
usage. Let's read out the HDPORT_STATE register and avoid making use of
resources that HTI is already using.
v2:
- Fix minor checkpatch warnings
v3:
- Just readout HDPORT_STATE register once during init and then parse it
later as needed.
- Add a 'has_hti' device info flag to track whether we should readout
HDPORT_STATE or not. We can skip the platform/flag tests later since
the hti_state in dev_priv will remain 0 for platforms it does not
apply to.
- Move PLL masking into icl_get_combo_phy_dpll() since at the moment
RKL is the only platform that has HTI. (Jose)
Bspec: 49189
Bspec: 53707
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-5-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Rocket Lake has a third DPLL (called 'DPLL4') that must be used to
enable a third display. Unlike EHL's variant of DPLL4, the RKL variant
behaves the same as DPLL0/1. And despite its name, the DPLL4 registers
are offset as if it were DPLL2.
v2:
- Add new .update_ref_clks() hook.
v3:
- Renumber TBT PLL to '3' and switch _MMIO_PLL3 to _MMIO_PLL (Lucas)
v4:
- Don't drop _MMIO_PLL3; although it's now unused, we're going to need
it very soon again for upcoming DG1 patches. (Lucas)
v5:
- Don't re-number TBT PLL and beyond, just use new RKL_DPLL_CFGCR
macros to lookup the proper registers instead. Although renumbering
the PLLs might be something we want to consider down the road, it
opens a big can of worms right now since a bunch of places in the
code have an assumption that the PLL table has idx==id and no holes.
Renumbering creates a hole for TGL, so we'd either need to allow
holes in the table or break the idx==id invariant, both of which are
somewhat invasive changes to the design.
Bspec: 49202
Bspec: 49443
Bspec: 50288
Bspec: 50289
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-4-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
RKL and TGL share some general gen12 workarounds, but each platform also
has its own platform-specific workarounds.
v2:
- Add Wa_1604555607 for RKL. This makes RKL's ctx WA list identical to
TGL's, so we'll have both functions call the tgl_ function for now;
this workaround isn't listed for DG1 so we don't want to add it to
the general gen12_ function.
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-3-matthew.d.roper@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
It's silly to have if(SKL) checks in gen9_init_clock_gating() when
we can just move those bits into skl_init_clock_gating().
I'm not entirely convinced we even need this w/a, or if we do
then maybe we want it for kbl/cfl as well. IIRC it was only
listed in the wadb, but that is now dead so can't double check
anymore. Bspec doesn't seem to have any purely skl specific
DOP clock gating workarounds listed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716190426.17047-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Hours Of Battery Life is a new GEN12+ power-saving feature that allows
supported motherboards to use a special voltage swing table for eDP
panels that uses less power.
So here if supported by HW, OEM will set it in VBT and i915 will try
to train link with HOBL vswing table if link training fails it fall
back to the original table.
intel_ddi_dp_preemph_max() was optimized to only check the HOBL flag
instead of do something like is done in intel_ddi_dp_voltage_max()
because it is only called after the first entry of the voltage swing
table was loaded so the HOBL flag is valid at that point.
v3:
- removed a few parameters of icl_ddi_combo_vswing_program() that
can be taken from encoder
v4:
- using the HOBL vswing table until training fails completely (Ville)
v5:
- not reducing lane or link rate when link training fails with HOBL
active
- duplicated the HOBL voltage swing entry to match DP spec requirement
v6:
- removed the optional VS 3 & pre-emp 0 from HOBL table
- changed from u8:1 to bool to store hobl_failed/active
BSpec: 49291
BSpec: 49399
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200715175637.33763-1-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
0x0155 is rather Ivy Bridge PCI-E Root Port.
0x0157 from the same commit ff049b6ce2 ("drm/i915: bind driver to ValleyView chipsets")
is likely wrong too. Nowhere is it independetly confirmed or mentioned.
Signed-off-by: Alexei Podtelezhnikov <apodtele@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428034752.3975-1-apodtele@gmail.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Rather than manually implement our own module reference counting for perf
pmu events, finally realise that there is a module parameter to struct
pmu for this very purpose.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716094643.31410-1-chris@chris-wilson.co.uk
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The value we program to DDI_BUF_CTL changes at the following places:
- At enabling/disabling the output to configure the port width etc, and
to enable/disable the DDI BUF function.
- At the beginning/end of link re-training to disable/re-enable the DDI
BUF function.
- On HSW/BDW/SKL to change the voltage swing/pre-emph levels.
Except of the above the value we program to the DDI_BUF_CTL register
(intel_dp->DP) doesn't change, so no need to reprogram the register when
changing the link training patterns (which is programmed via the
DP_TP_CTL register on DDI platforms).
v2:
- Fix the commit message wrt. voltage/pre-emph level values in
intel_dp->DP. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714153141.10280-2-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
According to BSpec this flag should not be changed while the DDI
function is enabled. On BDW+ the DP_TP_CTL register spec also states it
explicitly that the HW takes care of enabling/disabling the scrambling
for training patterns (and it must stay enabled for normal pixel
output). Assume that this HW automatic handling of scrambling is also
true for HSW.
BSpec: 8013, 7557, 50484
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714153141.10280-1-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Explicitly check for i830 when assigning the .get_cdclk() vfunc,
and then deal with the case of not having assigned the vfunc
separately. Less confusing, and gets rid of the checkpatch complaint
about using {} on one branch but not the others.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714152626.380-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There's a pointless hole in struct intel_cdclk_vals, get rid of it.
Fortunately we already use named initializers so the order does not
matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714152626.380-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since g4x the CFB base only takes a 28bit offset into stolen.
Not sure if the CFB is allowed to start below that limit but
then extend beyond it. Let's assume not and just restrict the
allocation to the first 256MiB (in the unlikely case
we have more stolen than that).
v2: s/BIT/BIT_ULL/ (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714201945.18959-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The drm_mode_config_reset patches are very important fixing a recently
introduced kernel crash, the others fix various older issues which are
a bit less serious in practice.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: "Roland Scheidegger (VMware)" <rscheidegger.oss@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200812005941.19465-1-rscheidegger.oss@gmail.com
* add orientation quirk for ASUS T103HAF
* drm/omap: force runtime PM suspend on system suspend
* drm/tidss: fix modeset init for DPI panels
* re-added docs for drm_gem_flink_ioctl()
* ttm: fix page-offset calculation within TTM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAl8pWYUACgkQaA3BHVML
eiNGkAf+Lw+DXDm1C9cpSm2oj9XFiwUBI25G+4aDn6+3o5YAdkWGkVSSqb8wXzaL
XTE8iMmCfsz/LXGIHGa3lOhhwj/zXMOH+Eg9xt+vXvYFuaoOUxeCSz8WiRg7bNwx
gfaQvsX+2lVBkfcyn8s8NEJOBvKSzRl3JQcUrY3QWnvUZcM37E4NueZOkeygAqFl
Jjcq6DdQOskUOzkQb+6lxDtiBJQZ6jTZWIcIW9Ec8Xc6VqsxuKLM3iv17Lo+5qbj
1Enj1YBnOwK8Rs3AvhvB8vRJ/y1MBImnc3bheLxTGZ5NAsxwLarg0jRqzSsxuDOS
t9xz3voeyYUVHN91uaIRENIyqfvtkg==
=gN9V
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2020-08-04' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
* backmerge from drm-fixes at v5.8-rc7
* add orientation quirk for ASUS T103HAF
* drm/omap: force runtime PM suspend on system suspend
* drm/tidss: fix modeset init for DPI panels
* re-added docs for drm_gem_flink_ioctl()
* ttm: fix page-offset calculation within TTM
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200804125510.GA29670@linux-uq9g
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8nLmkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGBEkH/RJAnEan4gcdkBDf
2xS0yk4XLMjKZwbz61VSeKMUBkGCsh1cWsaAtJJAIVYj/6o/7mld01sZCnOASLnJ
ET0nXL2NiT/f+prYkTE5qeYH225/Yfh5jgmrqZtx/uXFCwgE5Nzi3f72IXQDmCR+
kmpNhNox3YqQTKXhv7DXobDKcO0n8nZavnhxmA9SBZn2h9RHvmvJghD0UOfLjMpA
1SbknaE67n5JN/JjI6TkYWk4nuJmqfvmBL5IYVDEZYO4UlM5Bqzhw0XN7Ax70K3M
KRK/eiqRmNwun5MxWnbzQU7t7iTgVmzjHLTpWGcM3V4blgGXC3uhjc+p/R8KTQUE
bIydSzs=
=fDeo
-----END PGP SIGNATURE-----
Merge tag 'v5.8' into drm-next
I need to backmerge 5.8 as I've got a bunch of fixes sitting
on an rc7 base that I want to land.
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is a spelling mistake in a DRM_ERROR message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
There is a spelling mistake in a DRM_ERROR message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
Same problem as in stdu, same fix.
Fixes: 51f644b40b ("drm/atomic-helper: reset vblank on crtc reset")
Acked-by: Charmaine Lee <charmainel@vmware.com>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
Same problem as in stdu, same fix.
Fixes: 51f644b40b ("drm/atomic-helper: reset vblank on crtc reset")
Acked-by: Charmaine Lee <charmainel@vmware.com>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
When converting to atomic the state reset was done by directly calling
the functions, and before the modeset object was fully initialized.
This means the various ->dev pointers weren't set up.
After
commit 51f644b40b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jun 12 18:00:49 2020 +0200
drm/atomic-helper: reset vblank on crtc reset
this started to oops because now we're trying to derefence
drm_crtc->dev. Fix this up by entirely switching over to
drm_mode_config_reset, called once everything is set up.
Fixes: 51f644b40b ("drm/atomic-helper: reset vblank on crtc reset")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Roland Scheidegger <sroland@vmware.com>
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
These if statements are supposed to be true if we ended the
list_for_each_entry() loops without hitting a break statement but they
don't work.
In the first loop, we increment "i" after the "if (i == unit)" condition
so we don't necessarily know that "i" is not equal to unit at the end of
the loop.
In the second loop we exit when mode is not pointing to a valid
drm_display_mode struct so it doesn't make sense to check "mode->type".
Fixes: a278724aa2 ("drm/vmwgfx: Implement fbdev on kms v2")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
The "entry" pointer is an offset from the list head and it doesn't
point to a valid vmw_legacy_display_unit struct. Presumably the
intent was to point to the last entry.
Also the "i++" wasn't used so I have removed that as well.
Fixes: d7e1958dbe ("drm/vmwgfx: Support older hardware.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
