Using VFGEN_RSTAT to detect a VF reset is an endeavor that is fraught
with peril. It's entirely too easy to miss a reset because none of the
bits are sticky. By the time the VF driver reads the register, the reset
may have been processed and cleaned up by the PF driver, leaving the
register in the same state that it was before the reset.
Instead, detect a reset with the VF_ARQLEN register. When the VF is
reset, the enable bit in this register is cleared, and it stays cleared
until the VF driver processes the reset and re-enables the admin queue.
Because we now deal with multiple registers in the reset and watchdog
tasks, rename the rstat_val variable to reg_val.
Change-ID: Id1df17045c0992e607da0162d31807f7fc20d199
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes parsing of AQ command Get CEE DCBX OPER CFG (0x0A07). Change is
required because FW creates the oper_prio_tc nibbles reversed from those
in the CEE Priority Group sub-TLV.
Change-ID: I7d9d8641bb430d30e286fc3fac909866ef8a0de8
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ran into an issue where PF's VSI type list was different from VF's,
which was resulted in different enum index. The VSI type list can
be different depending on what build flag is used for PF and VF.
The change is to explicitly assign enum index for each VSI type
so that PF and VF always reference to the same VSI type event if the
enum lists are different.
Change-ID: I8c0e5fdb515f324f7964df863a458073cf467e57
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's been some need for controlling the periodic link polling for
debugging link issues. This patch enables switching it off and on
through an ethtool private flag. The link poll remains on by default,
but can be turned off with
ethtool --set-priv-flags p261p1 LinkPolling off
and later turned back on with
ethtool --set-priv-flags p261p1 LinkPolling on
To check the current status, use
ethtool --show-priv-flags p261p1
Change-ID: I32e4ab654ff3eec90a06cf144899971b82d71c40
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses an issue where multiple link up messages can be logged
resulting from aq link status timing when link properties are changed (fc,
speed, etc.); solved by using a single function to handle status printing
and adding a mechanism to track whether link state (up or down) has
actually changed.
Change-ID: Ied6ed6e49dc397c77d992adc0bc9ed3767152b9d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the PF's fdir filter table would have an
entry that the hw was unable to add. This notification happens in the hot
path, so instead of trying to fix it then, we note the location in the
failure case and delete it during regular fdir subtask callback. Without
this patch, a case can occur where an invalid entry gets replayed and a
valid one is not.
Change-ID: I67831c183b5d0309876de807cc434809b74c9cb7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds capability to query and store the CEE DCBX DesiredCfg
and RemoteCfg data from the LLDP MIB.
Added new member "desired_dcbx_config" in the i40e_hw data structure
to hold CEE only DesiredCfg data.
Change-ID: I19c550369594384eaff4cc63e690ca740231195d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds parsing for CEE DCBX TLVs from the LLDP MIB.
While the driver gets the DCB CEE operational configuration from Firmware
using the "Get CEE DCBX Oper Config" AQ command there is a need to get
the CEE DesiredCfg Tx by firmware and DCB configuration Rx from peer; for
debug and other application purposes.
Change-ID: I9140edf1a25a2852c7eff805d81e5eff6266178d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Under certain circumstances, the device may not have enough resources to
enable all of the VFs that it advertises in config space. Although the
number of supported VFs is reported upon driver init, it is not obvious
when this is different from the number reported in config space. To
eliminate this confusion, add an error message explaining the problem.
Additionally, move the 'Allocating VFs' message down below the error
checks so as to prevent further confusion.
Change-ID: I45b7efca53a7aebf7777be33a8bc9d615ae48ea1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The interrupt enable function can be inlined by moving it to the header
file, which decreases the function call overhead for a frequently called
function.
Change-ID: I3214cc99593725768642680e7b8ce7e9bba7e44d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was issuing a WARN_ON during ring size changes
because the code was cloning the rx_ring struct but
not zeroing out the pointers before allocating new memory.
Zero out the pointers in the cloned copy before allocating
new memory for them. In this case the code was correctly
avoiding memory leaks but still triggering the warning.
Change-ID: I186dd493948e9b7254ab0593d4aad8b68808918d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This opcode is not required. VFs that program RSS through the firmware
do it by interacting directly with the firmware, and do not need to use
the virtual channel for this functionality.
Change-ID: Iaf17d2600e28ff1b6be8653f2fe9df1facd23b0e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lower level functions are properly reporting errors, and higher-level
functions are correctly responding to errors, but the errors aren't
actually getting through. Typically, the middle-manager function seems
to want to shield its boss from any bad news.
This change fixes a panic if the driver is unable to enable MSI-X or is
unable to acquire enough vectors.
Change-ID: Ifd5787ce92519a5d97e4b465902db930d97b71a1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware has added additional status information to allow software
to determine if the APP priority for FCoE/iSCSI/FIP is valid or not in
CEE DCBX mode.
This patch adds to support those additional checks and will only add
applications to the software table that have oper and sync bits set
without any error.
Change-ID: I0a76c52427dadf97d4dba4538a3068d05e4eb56b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Keep track of how many times we ask the stack to linearize the
skb because the HW cannot handle skbs with more than 8 frags per
segment/single packet.
Change-ID: If455452060963a769bbe6112cba952e79e944b52
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using something like "ip maddr add ..." to add another unicast mac
address to the netdev, the mac address comes into the set_rx_mode handler
in the multicast list whether it is a unicast or multicast address.
This was confusing the code when it was trying to search for addresses
that needed to be deleted from the VSI, because it was looking for the
VSI unicast address in the netdev unicast list. The result was that a
new unicast address would get added to the VSI list and then immediately
removed, and would never actually make it down into the hardware.
This patch removes the separation from unicast and multicast in the search
for filters to be deleted. It also simplifies the logic a little with a
jump to the bottom of the loop when an address is found. Now it doesn't
matter which netdev list the address is hiding in, we'll check them all.
Change-ID: Ie3685a92427ae7d2212bf948919ce295bc7a874c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the driver could call this function and have only true/false
returned, but false could mean multiple things like failure to read
or link was down. This change allows the caller to get all return values
in the call chain bubbled back to the source, which keeps information about
failures from being lost.
Also, in some unlikely scenarios, the firmware can become slow to respond
to admin queue (AQ) queries for link state. Should the AQ time out,
the driver can detect the state and avoid a link change when there
may have been none.
Change-ID: Ib2ac38407b7880750fb891b392fa77457fe6c21c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The checksum is not correct on big endian machines so add code to swap it
correctly.
Change-ID: Ic92b886d172a2cbe49f5d7eee1bc78e447023c7b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During early development, we added the function name to all of the error
strings to make debugging simpler. Now that we've released the driver,
our users should have more comprehensible error messages. So tear the
roof off and give up the __func__. Ow.
Change-ID: I7e1766252c7a032b9af6520da6aff536bdfd533c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ethtool, there is a possibility of speed getting set to 0
if advertise is set to 0 (which it is when autoneg is disabled).
We never want this to happen as the firmware will actually attempt
to set the speed to 0 sending link down, so add an extra check
to make sure this doesn't happen.
Change-ID: I62e0eeee2cbf043d8e6f5c9c9f0b92794e877f01
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the size of the text available for the interrupt names.
Without this patch, all the descriptive data available for the Flow
Director interrupts is truncated.
Change-ID: I2ac458f23ac3b4ea8f1edf73edc283b1d3704c7f
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a possibility where the asq_last_status could get through without
update and thus report a previous error. I don't think we've actually seen
this happen, but this patch will help make sure it doesn't.
Change-ID: I9e33927052a5ee6ea21f80b66d4c4b76c2760b17
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Christopher Pau <christopher.pau@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_init_pf_fcoe() didn't return anything except 0, it prints enough
error info already, and no driver logic depends on the return value,
so this can be void.
Change-ID: Ie6afad849857d87a7064c42c3cce14c74c2f29d8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a shift value that was wrong, ending up with a bad bitmask. Also add
a blank line between two sets of #defines for better readability.
Change-ID: I3e41fa2a2ab904d3a4e6cbf13972ab0036a10601
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rework an if expression to assure there is no type compare problem between
a size and a possible negative number.
Change-ID: I4921fcc96abfcf69490efce020a9e4007f251c99
Reported-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Early addition of new a device id.
Change-ID: I61a8c8556fdf4f5714be4e4089689e374f30293c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Explicitly stop the rings belonging to each VF when disabling SR-IOV.
Even though the VFs were gone, and the associated VSIs were removed, the
rings were not stopped, and in some circumstances the hardware would
continue to access the memory formerly used by the rings, causing memory
corruption or DMAR errors, both of which would lead to general malaise
of the kernel.
To relieve this condition, explicitly stop all the rings associated with
each VF before releasing its resources.
Change-ID: I78c05d562c66e7b594b7e48d67860f49b3e5b6ec
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was disabling Wake-on-LAN by default and waiting for the user
to expressly turn it on. This patch has the driver turning on WoL from
the start if enabled in the hardware config, which matches the behavior
of our other drivers.
Change-ID: I43faedb907f8ba4d1a61b72a7c86072b97af12b1
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some rare cases the reset can take longer to complete so increase the
amount of time we wait.
Change-ID: Ib5628ec54b526a811ee33d1214fe763226406671
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The standard way to check if the AQ is enabled is to look at the
count field. So we should only set this field after we have
successfully allocated memory. To do otherwise is to incite
panic among the populace.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-03
This series contains updates to i40e and i40evf, some of which are to
resolve more Red Hat bugzilla issues.
Jiang Liu updates the i40e and i40evf drivers to use numa_mem_id()
instead of numa_node_id() to get the nearest node with memory which
better supports memoryless nodes.
Anjali fixes an issue from Dan Carpenter <dan.carpenter@oracle.com>,
to resolve a memory leak in X722 RSS configuration path, where we should
free the memory allocated before exiting.
Shannon modifies the drivers to ensure we have the spinlocks before we
clear the ARQ and ASQ management registers. In addition, we widen the
locked portion insert a sanity check to ensure we are working with safe
register values.
Mitch fixes an issue where under certain circumstances, we can get an
extra VF_RESOURCES message from the PF driver at runtime. When this
occurs, we need to parse it because our VSI may have changed and that
will affect the relationship with the PF driver. But this parsing also
blows away our current MAC address, so resolve the issue by restoring
the current MAC address from the netdev struct after we parse the
resource message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver still was not offloading TSO on GRE tunnels because
it forgot to set the GSO_GRE flag, causing lots of retransmits.
This fixes generic GRE traffic (like a tunnel added like below)
whereas before it would get 1Gb/s or less, now on a 10G adapter
it gets 8.7Gb/s.
ip ad ad 11.1.0.2/24 dev ens2f0
ip l set ens2f0 up
ip link add gre2 type gretap remote 11.1.0.1 local 11.1.0.2 dev ens2f0
ip l set gre2 up
ip ad ad 192.168.124.2/24 dev gre2
ping 192.168.124.1
netperf -H 192.168.124.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to deprecate the use of 'struct timespec' on 32-bit
architectures, as it is will overflow in 2038. The igb
driver uses it to read the current time, and can simply
be changed to use ktime_get_real_ts64() instead.
Because of hardware limitations, there is still an overflow
in year 2106, which we cannot really avoid, but this documents
the overflow.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain circumstances, we can get an extra VF_RESOURCES message
from the PF driver at runtime. When this happens, we need to parse it
because our VSI may have changed out from underneath us, and that will
affect our relationship with the PF driver.
However, parsing the resources message also blows away our current MAC
address in the hardware struct, usually with all zeros. When this
happens, the next time the interface is opened, it will have no MAC
address and will a) not work and b) complain.
Fix this issue by restoring the current MAC address from the netdev
struct after we parse the resource message.
Change-ID: I6cd1b624fc20432f81dc901166c8de195b8e0e65
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure we have the spinlocks before we clear the ARQ and ASQ management
registers. Also, widen the locked portion and make a sanity check earlier
in the send function to be sure we're working with safe register values.
Change-ID: I34b56044b33461ed780f3d2de8d62826cdf933f9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In any case free the memory allocated before exiting.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function i40e_clean_rx_irq() tries to reuse memory pages allocated
from the nearest node. To better support memoryless node, use
numa_mem_id() instead of numa_node_id() to get the nearest node with
memory.
This change should only affect performance.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function i40e_clean_rx_irq() tries to reuse memory pages allocated
from the nearest node. To better support memoryless node, use
numa_mem_id() instead of numa_node_id() to get the nearest node with
memory.
This change should only affect performance.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-30
This series contains updates to i40e and i40evf only.
Vasily Averin provides a couple of rtnl lock/unlock fixes for both i40e
and i40evf.
Shannon provides several updates and fixes, first fixes up a type clash
in i40e_aq_rc_to_posix(), where the error codes are signed values, so we
need to treat them as such. Then fixes up a padding issue where an
extra byte is added in i40e_aqc_get_cee_dcb_cfg_v1_resp to directly
acknowledge the padding. Updated i40e to keep debugfs register read
and writes from accessing outside of the io-remapped space. Added
support and device id for another 20 GbE device.
Jesse fixes the transmit hand workaround code for ARM that was causing
Tx hangs to still occur occasionally when there really was no hang. Then
fixed the receive dropped counter to show up in netstat interface.
Refactor the interrupt enable function since it was always making the
caller add the base_vector from the VSI struct which is already passed
to the function. Fix kbuild warnings found in 0day build infrastructure
by adding a harmless cast to a dev_info(), also fix 32 bit build
warnings found by sparse.
Greg fixed a configuration error that results if a port VLAN is set
for a VF before the VF driver is loaded, so that when the VF driver is
loaded the port VLAN is ignored.
Mitch fixes the use of QOS field consistently in
i40e_ndo_set_vf_port_vlan(). Modified the init timing of the driver
to increase stability on load/unload and SR-IOV enable/disable cycles.
Anjali updates i40e to not collect VEB stats if they are disabled in the
hardware for performance reasons.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse found some issues with 32 bit compilation, which probably should
at least work without warning. Not only that, but the code was wrong.
Thanks sparse!!
And thanks to the kbuild robot zero day testing for finding this issue.
$ make ARCH=i386 M=drivers/net/ethernet/intel/i40e C=2 CF="-D__CHECK_ENDIAN__"
CHECK drivers/net/ethernet/intel/i40e/i40e_main.c
include/linux/etherdevice.h:79:32: warning: restricted __be16 degrades to integer
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (32) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (42) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (39) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (40) for type unsigned long
CC: kbuild-all@01.org
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 0day build infrastructure found some issues in i40e, this
removes the warnings by adding a harmless cast to a dev_info.
CC: kbuild-all@01.org
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch tweaks the init timing of the driver just a little bit to
increase stability on load/unload and SR-IOV enable/disable cycles.
First, run the init_task loop a little quicker in order to reduce
overall init time.
Second, stagger the start of the init task based on the device's
PCIe function ID. This lessens the impact on the firmware when a
whole bunch of VFs are initialized simultaneously, e.g. enabling
SR-IOV without the VF driver blacklisted. For single VFs assigned
to VMs this will have no effect as the function ID will always be 0.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Down was requesting queue disables, but then exited immediately without
waiting for the queues to actually disable. This could allow any
function called after i40evf_down to run immediately, including
i40evf_up, and causes a memory leak.
This issue has been fixed in a recent refactor of the reset code, but
add a couple WARN_ONs in the slow path to help us recognize if we
reintroduce this issue or if we missed any cases.
Change-ID: I27b6b5c9a79c1892f0ba453129f116bc32647dd0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The interrupt enable function was always making the caller add
the base_vector from the VSI struct which is already passed to
the function. Just collapse the math into the helper function.
Change-ID: I54ef33aa7ceebc3231c3cc48f7b39fd0c3ff5806
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to performance reasons, VEB stats have been disabled in the hw. This
patch adds code to check for that condition before accumulating these
stats.
Change-ID: I7d805669476fedabb073790403703798ae5d878e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new device id and support for another 20Gb device.
Change-ID: Ib1b61e5bb6201d84953f97cade39a6e3369c2cf2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a useless message that blathers on whenever a vxlan port is deleted.
Change-ID: If63fb8cf38e56cf433b68e498f11389de51919ba
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't let the debugfs register read and write commands try to access
outside of the ioremapped space. While we're at it, remove the use of
a misleading constant.
Change-ID: Ifce2893e232c65c7a76c23532c658f298218a81b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i40e_ndo_set_vf_port_vlan, we were using the QOS value
inconsistently, sometimes shifting it, sometimes not. Do the shift-and-
or operation correctly, once, and use the result consistently everywhere
in the function.
Change-ID: I46f062f3edc90a8a017ecec9137f4d1ab0ab9e41
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e rx_dropped counter was not showing up in netstat -i.
Add the right counter to be updated with the stats.
Change-ID: I4dd552e9995836099184f9d9a08e90edb591155f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The arm writeback (arm_wb) code is used for kicking the Tx ring to
make sure any pending work is completed even if interrupts are
disabled. It was running when it didn't need to, and not clearing
the ring->arm_wb state after it was set. This caused Tx hangs
to still occur occasionally when there really was no hang.
Fix this by resetting the variable right after it was used.
Change-ID: I7bf75d552ba9c4bd203d40615213861a24bb5594
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The struct i40e_aqc_get_cee_dcb_cfg_v1_resp was originally defined with
word boundary layout issues, which most compilers deal with by silently
adding padding, making the actual struct larger than designed.
This patch adds an extra byte in fields reserved3 and reserved4 to directly
acknowledge that padding.
Because the struct doesn't actually change in size or layout, this doesn't
constitute a change in the API.
Change-ID: I53fa4741b73fa255621232a85fba000b0e223015
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a port VLAN is set for a given virtual function (VF) before the VF
driver is loaded then a configuration error results in which the port
VLAN is ignored when the VF driver is subsequently loaded. This causes
the VF's MAC/VLAN filters to not use the correct VLAN filter. This
patch ensures that the port VLAN filter is considered at the right time
during configuration of the VF's MAC/VLAN filters.
Change-ID: I28f404cbc21a4c6d70a7980b87c77f13f06685a4
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The error code sent into i40e_aq_rc_to_posix() are signed values, so we
really need to treat them as such.
Change-ID: I3d1ae0ee9ae0b1b6f5fc424f8b8cc58b0ea93203
Reported-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's possible that while we are waiting for the spinlock, another
entity (that owns the spinlock) has shut down the admin queue.
If we then attempt to use the queue, we will panic.
Add a check for this condition on the receive side. This matches
an existing check on the send queue side.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously to this patch, the hardware was removing
VLAN tags from the inner header of VXLAN packets. The
hardware configuration can be changed to leave the
packet alone since that is what the linux stack
expects for this type of VLAN in VXLAN packet.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In igb_sw_init() the sequence of calls was changed from
igb_init_queue_configuration()
igb_init_interrupt_scheme()
igb_probe_vfs()
to
igb_probe_vfs()
igb_init_queue_configuration()
igb_init_interrupt_scheme()
This results in adapter->flags not having the IGB_FLAG_HAS_MSIX bit set
during igb_probe_vfs()->igb_enable_sriov(). Therefore SR-IOV does not
get enabled properly and we run into a NULL pointer if the max_vfs
module parameter is specified (adapter->vf_data does not get allocated,
crash on accessing the structure).
[ 7.419348] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[ 7.419367] IP: [<ffffffffa02161c6>] igb_reset+0xe6/0x5d0 [igb]
[ 7.419370] PGD 0
[ 7.419373] Oops: 0002 [#1] SMP
[ 7.419381] Modules linked in: ahci(+) libahci igb(+) i40e(+) vxlan ip6_udp_tunnel udp_tunnel megaraid_sas(+) ixgbe(+) mdio
[ 7.419385] CPU: 0 PID: 4 Comm: kworker/0:0 Not tainted 4.2.0+ #153
[ 7.419387] Hardware name: Dell Inc. PowerEdge R720/0C4Y3R, BIOS 1.6.0 03/07/2013
[...]
[ 7.419431] Call Trace:
[ 7.419442] [<ffffffffa0217236>] igb_probe+0x8b6/0x1340 [igb]
[ 7.419447] [<ffffffff814c7f15>] local_pci_probe+0x45/0xa0
Prevent this by setting the IGB_FLAG_HAS_MSIX bit before calling
igb_probe_vfs(). The real interrupt capabilities will be checked during
igb_init_interrupt_scheme() so this is safe to do.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The sync_vsi_filters function can be called directly under RTNL
or through the timer subtask without one. This was causing a deadlock.
If sync_vsi_filters is called from a thread which held the lock,
and in another thread the PROMISC setting got changed we would
be executing the PROMISC change in the thread which already held
the lock alongside the other filter update. The PROMISC change
requires a reset if we are on a VEB, which requires it to be called
under RTNL.
Earlier the driver would call reset for PROMISC change without
checking if we were already under RTNL and would try to grab it
causing a deadlock. This patch changes the flow to see if we are
already under RTNL before trying to grab it.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue of forcing WB too often causing us to not
benefit from NAPI.
Without this patch we were forcing WB/arming interrupt too often taking
away the benefits of NAPI and causing a performance impact.
With this patch we disable force WB in the clean routine for X710
and XL710 adapters. X722 adapters do not enable interrupt to force
a WB and benefit from WB_ON_ITR and hence force WB is left enabled
for those adapters.
For XL710 and X710 adapters if we have less than 4 packets pending
a software Interrupt triggered from service task will force a WB.
This patch also changes the conditions for setting RS bit as described
in code comments. This optimizes when the HW does a tail bump and when
it does a WB. It also optimizes when we do a wmb.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the Tx checksum encoder knows about GRE protocol and sets the
descriptor flag appropriately.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the driver timeout logic by issuing a writeback
request via a software interrupt to the hardware the first time the
driver detects a hang. The driver was too aggressive in resetting a hung
queue, so back that off by removing logic to down the netdevice after
too many hangs, and move the function to the service task.
Change-ID: Ife100b9d124cd08cbdb81ab659008c1b9abbedea
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_get_head needs to be called in multiple files in a further patch,
prepare by moving the function into a header file.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the addition of X550em_x SFP+ support, the driver is now
functionally equivalent to what will be the 4.2.1 driver when
released, so change the version to match.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 thermal interrupt (IXGBE_EIMS_TS) is not an SDP, so it
doesn't need to be enabled in ixgbe_setup_gpie(). In fact the
value is simply not for the GPIE register at all.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82599 and X540 datasheets require that FCRTH be "set" for Tx
switching (VM-to-VM loopback) but it did not previously specify what
the value should be set to. It has now been determined that
the correct value is RXPBSIZE - (24*1024).
This setting is also required for later devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A logic error here results in the adapter_stopped flag only being
cleared when ixgbe_setup_fc returns an error. Correct the logic.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change does two things. First, it makes it so that we always
set the relaxed ordering bits related to the DCA registers even if
DCA is not enabled. Second, it moves the configuration out of the
ixgbe_down function and into the ixgbe_configure function before
enabling the Rx and Tx rings. This ensures that DCA is configured
correctly before starting to process packets.
Thanks to Alex Duyck for this fix.
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new device ID for X550EM device with SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch skips the PCI transactions pending check in
ixgbe_disable_pcie_master. This is done to addresses a known HW
issue where the PCI transactions pending bit sticks high when there
are pending transactions. HW engineering instructed to workaround
this issue by wait and then continue with our reset flow.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets RDRXCTL.PSP when the driver is in SRIOV mode which
enables padding of small packets.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting the X550* RDRXCTL register should fall through into X540
and 82599, not 82598.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The timeout path is supposed to release the semaphore, so do that.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Take control of an I2C mux that selects which SFP is attached to
the I2C bus. The control of the mux is captured in the taking and
releasing of the related semaphore. Because only port 1 can control
the mux, port 1 always leaves the mux set to select port 0.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the frequency of polling for SFP modules. Because the
service task sometimes runs at high rates, we can poll for
SFPs too often. When an SFP is not present, the I2C timeouts
that result are very costly. So, prevent SFP polling from
being done more than once every two seconds. To reduce latency,
the poll time is cleared in a couple of cases to permit the
next service task execution to poll the SFP module.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since SFP+ can be used with some X550 devices, permit them to be
detected.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some hardware platforms, the CS4227 does not initialize properly.
Detect those cases and reset it appropriately.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Configures the CS4227 correctly for both 1G and 10G operation,
by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It
needs to be in this function because we need both the module
type and the speed, and this is the only function in the init
flow that knows the speed. In contrast,
ixgbe_setup_sfp_modules_X550em() does not know the speed, so we
can't do anything useful here. This is a fundamental difference
from the previous flow, and is due to the way the CS4227 is
implemented.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds X550EM_x SFP+ dual-speed support. 82599 fiber link
code was moved from ixgbe_82599.c to ixgbe_common.c for use by
X550EM. SFP MAC link code is added to x550EM.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the number of retries during PHY detection. This reduces
pauses when no SFP is present. Once an SFP is detected, the normal
retry count will be used.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the destination location for I2C data initially so that
the received data will not be affected by previous attempts.
This could have returned wrong data in certain retry sequences.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the bit banging mode in the hardware when performing bit banging
I2C operations on X550. Also control the output enable on both the
clock and data lines.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The lan_id is being set after a previous I2C eeprom access which
makes no sense because it needs to be set before any access. Move
the setting to before the access.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most I2C accesses take and release semaphores for each access. Now
there is a reason to perform multiple I2C operations under the same
holding of the semaphore, so provide unlocked I2C methods for that
purpose.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Provide I2C combined operations on X550EM, not X550 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for the SFP insertion interrupt on X550EM devices with
SFPs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an SFP not present error is returned by the reset_hw method,
accept it and go on, since an SFP can still be inserted. Previously
it was only accepted for 82598 devices.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with 82599ES.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with I217-LM.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with I350.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device probe method e1000_probe calls e1000_init_eeprom_params
itself so there's no reason to call it again from e1000_do_write_eeprom
or e1000_do_read_eeprom.
The sentence above assumes that e1000_init_eeprom_params is effective.
e1000_init_eeprom_params depends mostly on hw->mac_type and e1000_probe
bails out early if it can't set mac_type (see e1000_init_hw_struct, then
e1000_set_mac_type), qed.
Btw, if effective, the removed paths would had been deadlock prone when
e1000_eeprom_spi was set:
-> e1000_write_eeprom (takes e1000_eeprom_lock)
-> e1000_do_write_eeprom
-> e1000_init_eeprom_params
-> e1000_read_eeprom (takes e1000_eeprom_lock)
(same narrative with e1000_read_eeprom -> e1000_do_read_eeprom etc.)
As a final note, the candidate deadlock above can't happen in e1000_probe
due to the way eeprom->word_size is set / tested.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a private ethtool flag to enable display of these statistics, which
are generally less useful. However, sometimes it can be useful for
debugging purposes. The most useful portion is the ability to see what
the PF thinks the VF mailboxes look like.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we connect to the mailbox, we insert a fake disconnect header so
that the code does not see an invalid header and thus instantly error
every time we bring up the mailbox. However, we incorrectly record the
tail and head from the local perspective. Since the remote end shouldn't
have anything for us, add a "create_fake_disconnect_hdr" function which
inverts the TAIL and HEAD fields. This enables us to connect without any
errors of either TAIL or HEAD incorrectness, and prevents creating
extraneous error messages. This is necessary now since mbx_reset_work
does not actually reset the Tx FIFO head and tail pointers, thus head
and tail might not be equivalent on a reconnect.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a corner case issue with the PF/VF mailbox code.
Currently, fm10k_mbx_reset_work clears various state about the mailbox.
However, it does not clear the Tx FIFO head/tail pointers. We can't
simply clear these pointers as we unintentionally drop untransmitted
messages without error.
Doing nothing results in a possible phantom re-transmission of messages,
since we leave tx.head and tx.tail intact, but clear the tx_pulled and
tail_len values. This means that the PF could continuously re-send a
message which triggers a reset in the VF. Upon reset, the VF will
re-receive the same message after a reconnect.
If we reset the tx.head and tx.tail pointers completely, we end up
dropping some messages that were pending before connect. This results in
missing LPORT_MSG_READY bits, and VFs will end up reporting no link.
However, we can resolve both issues by simply incrementing head to
account for the already transmitted messages, before we reset tx_pulled.
We do this via the same logic as fm10k_mbx_head_pull.
We account for the tail_len which includes all data not yet transmitted,
once we account for the acked data which means re-reading the HEAD
variable from the message header. Then, we drop messages until we've
dropped more than the new tx_pulled value. At this point, resetting
tail_len and tx_pulled, but not tx.head and tx.tail will result in
prevention of the phantom message. It also prevents us from dropping
untransmitted messages upon attempting to Tx into a connect or
disconnect header.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 has HW support for SCTP flow director filters SCTP mask. This
patch adds it like we do for UDP and TCP.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is part of the future enablement of X550 SFP+ support. This
HW uses different SDP so the interrupts need to be set up accordingly.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This comment is no longer true due to a couple of mailbox locking
refactors, and we now don't actually do any rtnl protected operations
directly in the mailbox path. Remove this comment as it is factually
incorrect and confusing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a facility to recover the result of a previously run AQ command.
Change-ID: I21afec2c20c1a5e6ba60c7fbfcbedfff78c10e45
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a facility to run AQ commands through the nvmupdate utility in order
to allow the update tools to interact with the FW and do special
commands needed for updates and configuration changes.
Change-ID: I5c41523e4055b37f8e4ee479f7a0574368f4a588
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds wait states to the NVM update state machine to signify when
waiting for an update operation to finish, whether we're in the middle
of a set of Write operations, or we're now idle but waiting.
Change-ID: Iabe91d6579ef6a2ea560647e374035656211ab43
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds a new GetStatus command so that the NVM update tool can query
the current status instead of doing fake write requests to probe for
readiness.
Change-ID: I671ec6ccd4dfc9dbac3a03b964589d693fda5cd8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the writeback descriptor buffer was previously created, this gives it
to the AQ command request to be used to save the results.
Change-ID: I8c8a1af81e6ebed6d0a15ed31697fe1a6c4e3708
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the ability to save the AdminQ write back descriptor if a
caller supplies a buffer for it to be saved into.
Change-ID: I3d1301d26360b39a2d66dc8569e851f54133a3af
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code returns something that becomes the errno value from ethtool and
passes around a pointer to an errno variable. This patch changes the name
slightly to differentiate it from the actual user errno variable.
Change-ID: Idaa37845c069e66f4cea072e90f471bb2142454d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF will send a message to request multicast addresses with the
default VID. In the current code, if the PF has statically assigned a
VLAN to a VF, then the VF will not get the multicast addresses. Fix up
all of the various VLAN messages to use identical checks (since each
check was different). Also use set as a variable, so that it simplifies
our check for whether VLAN matches the pf_vid.
The new logic will allow set of a VLAN if it is zero, automatically
converting to the default VID. Otherwise it will allow setting the PF
VID, or any VLAN if PF has not statically assigned a VLAN. This is
consistent behavior, and allows VF to request either 0 or the
default_vid without silently failing.
Note that we need the check for zero since VFs might not get the default
VID message in time to actually request non-zero VLANs.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we only trigger the data path reset if the
fabric is ready to handle traffic. The general idea is to avoid
triggering the reset unless the switch API is ready for us. Otherwise
we can just postpone the reset until we receive a switch ready
notification.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify behavior of Malicious Driver Detection events. Presently, the
hardware disables the VF queues and re-assigns them to the PF. This
causes the VF in question to continuously Tx hang, because it assumes
that it can transmit over the queues in question. For transient events,
this results in continuous logging of malicious events.
New behavior is to reset the LPORT and VF state, so that the VF will
have to reset and re-enable itself. This does mean that malicious VFs
will possibly be able to continue and attempt malicious events again.
However, it is expected that system administrators will step in and
manually remove or disable the VF in question.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch ensures that VLAN traffic on the default VID will go to the
corresponding VLAN device if it exists. To do this, mask the rx_ring VID
if we have an active VLAN on that VID.
For this to work correctly, we need to update fm10k_process_skb_fields
to correctly mask off the VLAN_PRIO_MASK bits and compare them
separately, otherwise we incorrectly compare the priority bits with the
cleared flag. This also happens to fix a related bug where having
priority bits set causes us to incorrectly classify traffic.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some style issues in debugfs code, and correct ordering of void and
__always_unused. Technically, the order does not matter, but preferred
style is to put the macro between the type and name.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function is no longer used now that we have updated fm10k_slot_warn
functionality.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we store the sw_vid at reset of PF, then we accidentally prevent the
VF from receiving the message to update its default VID. This only
occurs if the VF is created before the PF has come up, which is the
standard way of creating VFs when using the module parameter.
This fixes an issue where we request the incorrect MAC/VLAN
combinations, and prevents us from accidentally reporting some frames as
VLAN tagged.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We re-sync upon going up, so there is little reason to worry about not
syncing immediately with switch. This prevents an error that occurs if
you add a VLAN interface while down.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds the MAC address to the list of values recorded on driver
load. The MAC address represents the serial number of the unit and allows
us to track the value should a card be replaced in a system.
The log message should now be similar in output to that of ixgbe.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change pulls out the optimization that assumed that all fragments
would be limited to page size. That hasn't been the case for some time now
and to assume this is incorrect as the TCP allocator can provide up to a
32K page fragment.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the netdev permanent address during fm10k_reinit enables the user
to immediately see the new MAC address on the VF even if the device
isn't up. The previous code required that the device by opened before
changes would appear.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is useful in cases where we connect to a slot at Gen3, but the slot
is behind a bus which only connected at Gen2. This generally only
happens when a PCIe switch is in the sequence of devices, and can be
very confusing when you see slow performance with no obvious cause.
I am aware this patch has a few lines that break 80 characters, but
there does not seem to be a readable way to format them to less than 80
characters. Suggestions welcome.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows us to correctly add a VLAN even if it matches our default
VID. However, we don't want to remove the VID rules once that VLAN is
deleted. Correctly remove the stack layers information of the VLAN, but
then return to forwarding that VID as untagged frames. If we deleted the
VID rules here, we would begin dropping traffic due to VLAN membership
violations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The service task reads some registers as part of its normal routine,
even while the interface is down. Normally this is ok. However, during
suspend we have disabled the PCI device. Due to this, registers will
read in the same way as a surprise-remove event. Disable the service
task while we suspend, and re-enable it after we resume. If we don't do
this, the device could be UP when you suspend and come back from resume
as closed (since fm10k closes the device when it gets a surprise
remove).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the lowest limit for adaptive interrupt interrupt
moderation to roughly 12K interrupts per second.
The way I came about reaching 12K as the desired interrupt rate is by
testing with UDP flows. Specifically I had a simple test that ran a
netperf UDP_STREAM test at varying sizes. What I found was as the packet
sizes increased the performance fell steadily behind until we were only
able to receive at ~4Gb/s with a message size of 65507. A bit of digging
found that we were dropping packets for the socket in the network stack,
and looking at things further what I found was I could solve it by increasing
the interrupt rate, or increasing the rmem_default/rmem_max. What I found was
that when the interrupt coalescing resulted in more data being processed
per interrupt than could be stored in the socket buffer we started losing
packets and the performance dropped. So I reached 12K based on the
following math.
rmem_default = 212992
skb->truesize = 2994
212992 / 2994 = 71.14 packets to fill the buffer
packet rate at 1514 packet size is 812744pps
71.14 / 812744 = 87.9us to fill socket buffer
From there it was just a matter of choosing the interrupt rate and
providing a bit of wiggle room which is why I decided to go with 12K
interrupts per second as that uses a value of 84us.
The data below is based on VM to VM over a direct assigned ixgbe interface.
The test run was:
netperf -H <ip> -t UDP_STREAM"
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
Before:
212992 65507 60.00 1100662 0 9613.4 10.89 0.557
212992 60.00 473474 4135.4 11.27 0.576
After:
212992 65507 60.00 1100413 0 9611.2 10.73 0.549
212992 60.00 974132 8508.3 11.69 0.598
Using bare metal the data is similar but not as dramatic as the throughput
increases from about 8.5Gb/s to 9.5Gb/s.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
This also includes a modified check generating the EICR mask to be
more forward-looking.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve warnings resulting from redundant initialization of the
get_bus_info field in the mac_ops_X550* structures.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When unbinding an SR-IOV device with VFs configured from ixgbe, the
driver behaves in one of two ways. If max_vfs was specified, the
SR-IOV state is disabled, removing the VFs. The occurs regardless of
whether the VF count was later modified through sysfs. If however
max_vfs is zero, such as by not specifying the module parameter, the
VFs persist after the PF is unbound from ixgbe. If the PF is then
bound to vfio-pci to be assigned to a VM, the PF is non-functional.
>From the comment, commit da36b64736 ("ixgbe: Implement PCI SR-IOV
sysfs callback operation") clearly intended this alternate behavior,
but probably didn't realize the PF doesn't work in this mode.
This bimodal behavior is confusing to users and results in a state
where the PF is broken for other uses unless the user sets
sriov_numvfs to zero prior to unbinding the device. Remove this
behavior so that VFs are removed and the PF is functional for other
uses after unbind, regardless of the way VFs are enabled.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we can do 2.5G link speed, we need to be able to report it.
Also change the nested triadic involved in creating the log message
to instead use a simpler switch statement to set a string pointer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue where users were not able to dynamically
set number of queues for 82598 via ethtool -L
Reported-by: Tal Abudi <talabudi@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allows to change the rxfh indirection table and/or key using
ethtool interface.
Signed-off-by: Tom Barbette <tom.barbette@ulg.ac.be>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid a needless PHY access on copper phys to save the 10ms wait
time for each PHY access. A helper function is introduced to
actually do the register access and process the contents.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We already cache this FW/SW semaphore mask so might as well use it
for consistency.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the redundant lan_id in the phy struct and uses
the bus version. Both variables exist and intend to represent the
STATUS register LAN_ID field. However, phy.lan_id is not bit shifted
so the phy.lan_id = 0x0 for LAN Id 0 and phy.lan_id = 0x4 for LAN Id 1.
Where bus.lan_id is bit shifted so bus.lan_id = 0x0 for LAN Id 0 and
bus.lan_id = 0x1 for LAN Id 1. There seems no need for the additional
lan_id variable and this should make the code less confusing.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use kzalloc rather than kcalloc(1..
The semantic patch that makes this change is as follows:
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
and removing checkpatch below CHECK:
CHECK: Prefer kzalloc(sizeof(*fwd_adapter)...) over
kzalloc(sizeof(struct ixgbe_fwd_adapter)...)
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe never has as very doubtfully ever will support either
PCI or PCI-X devices. So remove the unused types from the
ixgbe_bus_type. Thanks to Alex Duyck for suggesting this.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this patch we add support for a new bus type ixgbe_bus_type_internal.
X550em devices use IOSF and not PCIe bus so this new type is to accommodate
them.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added ixgbe_get_bus_info_X550em to X550 code. ixgbe_get_bus_info_X550em
sets bus.width to ixgbe_bus_width_unknown and bus.speed to
ixgbe_bus_speed_unknown, because IOSF does not report a PCIe bus
width or speed.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is closing or suspending, call ixgbe_enter_lplu to
enter low power link up state on devices that support it. When this
is done, prevent the phy from being reset in the ixgbe_down path
so that link is present when calling ixgbe_enter_lplu.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for VXLAN RX offloads for the X55x devices that support
them.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By using GSO for UDP-encapsulated packets, all ixgbe devices can
be directed to generate checksums for the inner headers because
the outer UDP checksum can be zero. So point the machinery at the
inner headers and have the hardware generate the checksum.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wait up to about 100 us for FDIRCMD writes to complete and return
failure indications.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are various reasons why this method may or may not need to be
defined and some of these we don't know until runtime. So we will
set the value in get_invariants.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a support function that will indicate for the
existence of management FW.
Signed-off-by: Donald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes bugs where the port is not receiving multicast or VLAN tagged
packets when in promiscuous mode. This can occur when a SW bridge is
created on top of the device.
This also fixes issues where the promiscuous behavior setting was not
being preserved across a reset caused by features being enabled or
disabled.
We are using defport instead of doing a true promiscuous mode because we do
not need to receive the SRIOV or VMDq VSI directed traffic which would suck
up bandwidth and is really not intended for the SW bridge.
In addition, with defport we get VLAN promiscuous behavior which is not
possible from the VSI level promiscuous setting.
Change-ID: Ie21985eac32d5af1c02e9d71c6430a90d5bab40f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version and update the copyright year for i40evf.
Change-ID: Iddb81b9dba09f0dc57ab54937b5821ecdd721ff6
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the CEE TLV status returned by firmware to allow drivers to dump that
for debug purposes.
Change-ID: Ie3c4cf8cebabee4f15e1e3fdc4fc8a68bbca40ee
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel notifies all VXLAN capable registered drivers, i.e. any
driver that implements ndo_add_vxlan_port(), of the addition of a
port so that the driver can track which ports are in use. There's
no need to log this - it just fills the system log with useless and
irksome noise.
Also, when failing to init SR-IOV interfaces the driver was printing the
same message twice. Just remove the inner printk and let the outer message
catch enable as well as the other failures.
Change-ID: Id5ecb1d425c2a357ee2bc1635dab24553831dade
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were quite a few issues when the wrong defines were getting used
in the VF driver. This patch fixes the code where PF driver registers
were getting used for VF driver, and also removes the registers that are
not being used from the VF register file.
Change-ID: If116a9730112950d006eb8ec763998fc914cc839
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use CTLN1 instead of CTLN for the VF relative register space.
Change-ID: Iefba63faf0307af55fec8dbb64f26059f7d91318
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Turns out that 'inavlid' is an inavlid spelling for 'invalid'.
Change-ID: Ie1fe2d0f8d1ba75ab880594875ec2e4152a76f61
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing comment is incorrect. Add new comment to point out that the
PF reset does not affect link but if the reset is changed to a different
type that does affect link then the link test would need to be moved to
before the reset.
Change-ID: I28d786f46e9465860babdee61c1dba51016464df
Reported-by: Jeremiah Kyle <jeremiah.kyle@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds capability to update per VEB per TC statistics and dump
it via ethtool. It also adds a structure to hold VEB per TC statistics.
The fields can be filled by reading the GLVEBTC_* counters.
Change-ID: I28b4759b9ab6ad5a61f046a1bc9ef6b16fe31538
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Treat netqueues the same way we do virtual functions when someone wants to
run the ethtool offline diagnostic test.
Change-ID: Id48d2b933f1fd0db7be06305a93c6ebe3dc821f5
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the driver flow to take into account legacy interrupts.
Over time we added code that assumes MSIX is the only mode that the
driver runs in. It also enables a legacy workaround to trigger SWINT
when the TX ring has non-cache aligned descriptors pending and interrupts
are disabled.
We work with a single vector in MSI mode too, so apply the same
restrictions as Legacy.
Change-ID: I826ddff1f9bd45d2dbe11f56a3ddcef0dbf42563
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should be stopping the service task and flow director on
shutdown not on suspension.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The port.crc_errors is really an RX counter, so let's mark it as such.
Change-ID: I179afd3f8a95d45229bb4163a6aeb01f0d2d250b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sparse cries when we compare an __le16 to a u16, almost like it cares
about architectures other than x86. Weird. Use the le16_to_cpu macro to
make it stop crying.
Change-ID: Id068f4d7868a2d3df234a791a76d15938f37db35
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit c48a11c7ad ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Simplify port-specific macros by eliminating explicit comparison
with 0. More importantly, enclose formal parameter in parens to
eliminate the risk of an operator precedence surprise.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes to igb_probe_vfs() could lead to the PF holding onto all
of the queues. Reorder igb_probe_vfs() to be before
gb_init_queue_configuration() and add some more error checking.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In error handling code of igb_probe, the memory adapter->shadow_vfta
allocated by kcalloc in igb_sw_init is not freed. So when register_netdev
or igb_init_i2c is failed, a memory leak will occur.
This patch adds kfree to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When e1000e_setup_rx_resources is failed in e1000_open,
e1000e_free_tx_resources in "err_setup_rx" segment is executed.
"writel(0, tx_ring->head)" statement in e1000_clean_tx_ring
in e1000e_free_tx_resources will cause a null poonter dereference(crash),
because "tx_ring->head" is only assigned in e1000_configure_tx
in e1000_configure, but it is after e1000e_setup_rx_resources.
This patch moves head/tail register writing to e1000_configure_tx/rx,
which can fix this problem. It is inspired by igb_configure_tx_ring
in the igb driver.
Specially, thank Alexander Duyck for his valuable suggestion.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When igb_init_interrupt_scheme in igb_sriov_reinit is failed, the lock
acquired by rtnl_lock() is not released, which causes a deadlock.
This patch adds rtnl_unlock() in error handling to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When pci_dma_mapping_error in e100_xmit_prepare is failed, the skb buffer
allocated by netdev_alloc_skb_ip_align in e100_rx_alloc_skb is not
released, which causes a possible resource leak.
This patch adds error handling code to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver lacks the check of nic->cbs_pool after pci_pool_create
in e100_probe. When this function is failed, a null pointer dereference
occurs when pci_pool_alloc uses nic->cbs_pool in e100_alloc_cbs.
This patch adds a check and related error handling code to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the .remove() callback for a PF is called, SR-IOV support for the
device is disabled, which requires unbinding and removing the VFs.
The VFs may be in-use either by the host kernel or userspace, such as
assigned to a VM through vfio-pci. In this latter case, the VFs may
be removed either by shutting down the VM or hot-unplugging the
devices from the VM. Unfortunately in the case of a Windows 2012 R2
guest, hot-unplug is broken due to the ordering of the PF driver
teardown. Disabling SR-IOV prior to unregister_netdev() avoids this
issue.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for Marvell PHY 1512 (required for I354).
Submitted by: Maciej Szwed <maciej.szwed@intel.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In addition to interrupt driven target time output events, the i210
also has two programmable clock outputs. These clocks support periods
between 16 nanoseconds and 140 milliseconds. This patch implements
the periodic output function using the clock outputs when possible,
falling back to the target time for longer periods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During driver probing the following code path is triggered.
igb_probe
->igb_sw_init
->igb_probe_vfs
->igb_pci_enable_sriov
->igb_sriov_reinit
Doing the SR-IOV re-init is not necessary during probing since we're
starting from scratch. Here we can call igb_enable_sriov() right away.
Running igb_sriov_reinit() during igb_probe() also seems to cause
occasional packet loss on some onboard 82576 NICs. Reproduced on
Dell and HP servers with onboard 82576 NICs.
Example:
Intel Corporation 82576 Gigabit Network Connection [8086:10c9] (rev 01)
Subsystem: Dell Device [1028:0481]
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When initializing igb driver (e.g. 82576, I350), IGB_FLAG_QUEUE_PAIRS is
set if adapter->rss_queues exceeds half of max_rss_queues in
igb_init_queue_configuration().
On the other hand, IGB_FLAG_QUEUE_PAIRS is not set even if the number of
queues exceeds half of max_combined in igb_set_channels() when changing
the number of queues by "ethtool -L".
In this case, if numvecs is larger than MAX_MSIX_ENTRIES (10), the size
of adapter->msix_entries[], an overflow can occur in
igb_set_interrupt_capability(), which in turn leads to an oops.
Fix this problem as follows:
- When changing the number of queues by "ethtool -L", set
IGB_FLAG_QUEUE_PAIRS in the same way as initializing igb driver.
- When increasing the size of q_vector, reallocate it appropriately.
(With IGB_FLAG_QUEUE_PAIRS set, the size of q_vector gets larger.)
Another possible way to fix this problem is to cap the queues at its
initial number, which is the number of the initial online cpus. But this
is not the optimal way because we cannot increase queues when another
cpu becomes online.
Note that before commit cd14ef54d2 ("igb: Change to use statically
allocated array for MSIx entries"), this problem did not cause oops
but just made the number of queues become 1 because of entering msi_only
mode in igb_set_interrupt_capability().
Fixes: 907b783579 ("igb: Add ethtool support to configure number of channels")
CC: stable <stable@vger.kernel.org>
Signed-off-by: Shota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the algorithm. Read systimel twice and check for overflow.
If there was no overflow, use the first value.
If there was an overflow, read systimeh again and use the second
systimel value.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes wrong locking usage.
In the context of slot reset, we should use lock.
And during resume, there is no need of lock.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Replace spaces with tab.
2) Move ich8lan related define to the proper context.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the EEE in Sx code so that it only applies to parts
that support EEE in Sx (as opposed to all parts that support EEE).
It also uses the existing eee_advert and eee_lp_abiliity to set just the
bits (100/1000) that should be set.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 does NVM update via the adminq queue, so we need to add support for
that.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports evicting ATR filters in the HW. With this patch, we enable
the feature in the driver and avoid filter deletion by the driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports IWARP, this patch handles checking for PE critical errors.
Since the driver doesn't support the IWARP interface for now, this patch
just does bare minimum to log a message oif a PE critical error
happens.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports offloading of outer UDP TX and RX checksum for tunneled
packets. This patch exposes the support and leaves it enabled by
default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.
X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the i40e and i40evf register.h file with the registers for X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does the firmware API update to support the new X722 device.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add capabilities flags specific to X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding device ids for new hardware X722
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with kernel requirements.
NOTE: the adminq_cmd.h file was not modified on purpose because
of the dependency upon firmware for that file.
Change-ID: I73ee2e48c880d671948aad19bd53ca6b2ac558fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up a little confusion in reporting error status in phy and fcoe
setup error reports by separating the return status from the AQ error.
Add two decoder functions to make this easier.
Change-ID: I960bcdeef3978a15fec1cdb5eff781d5cbae42fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This driver fully supports VF drivers using both the 1.0 and 1.1
versions of the virtual channel API. However, VF drivers using
version 1.0 get upset if we provide them with a version other than
that, and refuse to play with us.
Correct this by checking the VFs API version at the time that we
store it off, and provide the correct version number back to the VF
so we can all get along.
Change-ID: I86dfe02e67b2bef336b4b49a1bb072f3e7229abc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store off the PF's API version, then use it to determine whether or not
to send it our capabilities. Change the version checking to allow for PF
drivers with lower API versions than our current version, so we can
still talk to PF drivers over the 1.0 API.
Change-ID: I8edc55d1229c7decf0ed3f285a63032694007c2e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The most common type of reset that the VF will encounter is a PF reset
that cascades down into a VF reset for each VF. In this case, the VF
will always be assigned the same VSI and recovery is fairly simple.
However, in the case of 'bigger' resets, such as a Core or EMP reset,
when the device is reinitialized, it's probable that the VF will NOT get
the same VSI. When this happens, the VF will not be able to recover, as
it will continue to request resources for its original VSI.
Add an extra state to the admin queue state machine so that the driver
can re-request its configuration information at runtime. During reset
recovery, set this bit in the aq_required field, and fetch the (possibly
new) configuration information before attempting to bring the driver
back up. Since the driver doesn't know what kind of reset it has
encountered, this step is done even for a PF reset, but it doesn't hurt
anything - it just gets the same VSI back.
Change-ID: I915d59ffb40375215117362f4ac7a37811aba748
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store off the VF API version for use when figuring out the VF driver
capabilities. Add support for the VF driver handing its capabilities to
the PF driver and then use this information when sending VF resource
information back to the VF driver.
Change-ID: Ic00d0eeeb5b8118085e12f068ef857089a8f7c2d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we've rolled the virtual channel API version to 1.1, add some
macros to test what version is being used by our partner in crime. For the
VF, add some macros to determine what our device capabilities are.
Change-ID: I79f6683d4c23bd76a8ad9fd492776fcc1208e1dc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prepare for the changes coming up in the X722 device and future
devices, the virtual channel interface has to change slightly. The VF
driver can now report what its capable of supporting, which then informs
the PF driver when it sends the configuration information back to the
VF.
A 1.1 VF driver on a 1.0 PF driver should not send its capabilities.
Likewise, a 1.1 PF driver controlling a 1.0 VF driver should not expect
or depend upon receiving the VF capabilities.
All other aspects of the API are unchanged.
Change-ID: I530cc55f107edd1ee8bdf95830aa90b87854058a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With a little work we can clean up some unnecessary logic jumping and
drop a variable.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the switch statement for dynamic interrupt throttling
and adds a default case. With this patch, we check the latency setting
instead of the current ITR settings and the included refactor improves
performance.
Without this patch, the ITR setting would never change dynamically, and
there was no default.
Change-ID: Idb5a8a14c7109ec47c90f6e94bd43baa17d7ee37
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the ARRAY_SIZE macro rather than calculating sizeof(a)/sizeof(a[0]).
Also directly replace the code rather than using an unnecessary define.
Reported-by: Maninder Singh <maninder1.s@samsung.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are many settings possible using ethtool -C/--coalesce, but not
all of them are supported in igb. Report failure when an unsupported
option is set.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver lacks pm_qos_remove_request in error handling (err_req_irq) of
e1000_open, and qos request inserted by pm_qos_add_request is not removed.
This patch add pm_qos_remove_request in error handling to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the reporting of the RSS key and hash table by
adding support for X550 VFs. The difference is that X550 VFs have
their own registers for RSS key and indirection table, so there is
no need to query the PF.
The RSS key and indirection table are stored in the adapter structure
during the configuration of VFRSSRK and VFRETA which in turn can be
used in ethtool for reporting.
The logic for writing VFRETA is also changed to make sure that the
indirection table is reported correctly.
In addition this patch adds defines for the VFRETA entries and number
of VFRSSRK registers as well as some whitespace cleanups.
Reported-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000_check_for_link_media_swap() checks PHY page 0 for copper and PHY
page 1 for "other" (fiber) link. The switch back from page 1 to page 0
happened too soon, before e1000_check_for_link_82575() is executed, and
link on fiber (other) was never detected. Check for link while still on
the proper PHY page.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For two reasons I want to disable this:
1. Not any part actually check the report status(Alexander Duyck)
2. To report hash value of a packet to stack,
RSS -> 32bits hash value
Perfect match fdir filter -> 13bits hash value
Hashed-based fdir filter -> 31bits hash value
fdir filter might hash on masked tuples for IP address,
so it's still not desirable for usage.
So for now, just stick to RSS 32bits hash value.
Signed-off-by: Fan Du <fan.du@intel.com>
Suggested-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set hash type for ingress packets according to NIC
advanced receive descriptors RSS type part.
Signed-off-by: Fan Du <fan.du@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSS could be leveraged by taking account L4 src/dst ports
as ingredients, thus ingress skb Rx hash type should honor
such the real configuration.
Signed-off-by: Fan Du <fan.du@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change folds the ixgbevf_pull_tail call into ixgbevf_add_rx_frag. The
advantage to doing this is that the fragment doesn't have to be modified
after it is added to the skb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we pull the timestamp from the fragment before
we add it to the skb. By doing this we can avoid a possible issue in which
the fragment can possibly be less than IGB_RX_HDR_LEN due to the timestamp
being pulled after the copybreak check.
While making this change I realized we could also pull the rest of the
igb_pull_tail function into igb_add_rx_frag since in the case of igb,
unlike ixgbe, we are able to unmap the entire buffer before calling
add_rx_frag so merging the two allows for sharing of code between the two
merged functions.
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump.
Change-ID: I84573d9fa51effc5b29bf5b8c74e3cc8b2673f48
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change a warning message to indicate what may have really happened when
the init_shared_code call fails.
Change-ID: I616ace40fed120d0dec86dfc91ab2d7cde466904
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_add_pd_table_entry() routine is being modified to handle both
cases where a backing page is passed and where backing page is allocated
in i40e_add_pd_table_entry().
For PBLE resource management, it is more efficient for it to manage its
backing pages. For VF, PBLE backing page addresses will be send to PF
driver for PBLE resource.
The i40e_remove_pd_bp() is also modified to not free pre-allocated pages and
free only ones which were allocated in i40e_add_pd_table_entry().
Change-ID: Ie673f0403f22979e9406f5a94048dceb91bcf9a8
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During close, all of the MAC filters are cleared, so the driver would be
unable to receive unicast packets after being closed and reopened.
Add the adapter's "hardware" MAC address filter in open, not init. This
ensures that the correct filter is present each time.
Change-ID: I51a11e9c1200139dab6f66a5353bd38c7d26f875
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to an inverted conditional, the driver was marking all of its MAC
filters for deletion every time set_rx_mode was called. Depending upon
the timing of the calls to set_rx_mode and the processing of the admin
queue, the driver would (accidentally) end up with a varying number of
functional filters.
Correct this logic so that MAC filters are added and removed correctly.
Add a check for the driver's "hardware" MAC address so that this filter
doesn't get removed incorrectly.
Change-ID: Ib3e7c4a5b53df6835f164fe44cb778cb71f8aff8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a VF is disabled, there is no way for it to recover until either
the PF driver is reloaded or SR-IOV is disabled and enabled. To correct
this, enable the VF after a successful reset.
Change-ID: I9e0788476c4d53d5407961b503febdfff2b8a7c6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF disable code was just whanging on the reset bit without properly
cleaning up the VF, which would leave the VF in an indeterminate state
from which it could not recover. Fix this by notifying the VF and then
by calling the normal VF reset routine.
Change-ID: I862b9dfa919368773cbdc212b805b520db2f7430
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
MAC filters for VFs were being programmed with 0 for the VLAN value when
there was no VLAN assigned. This is incorrect and actually assigns the
VF to VLAN 0. Instead, we must use -1 to indicate that no VLAN is in
use. This change programs the filters correctly and gets rid of a bogus
error message when setting a port VLAN on an active VF.
Change-ID: Ica9a9906d768405377ff3308e27f7d0b5b2ea96e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the necessary updates to i40e_adminq_cmd.h.
Change-ID: Ib031c86cc6cab78e5aa44c64d8ce5474be8d7e42
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes some #ifdef's that should not be there. They
were stopping code that is needed from being compiled in.
With these #ifdef's removed, changes are needed in the driver
to fix some compile errors: adding missing parameters to
the definition of ndo_bridge_setlink and a ndo_dflt_brige_getlink call.
Change-ID: I5516614e1bc50b6bca0647cef971bc96161ba2de
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If user attempts to set a port VLAN on a VF that already has the same
port VLAN configured, the driver will go through a completely
unnecessary flurry of filter removals and filter adds. Just check for
this condition and return success instead of doing a bunch of busywork.
Change-ID: Ia1a9e83e6ed48b3f4658bc20dfc6af0cf525d54a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver currently only maps TX and RX queues to a single MSI-X vector
per queue pair if there are exactly enough vectors for this.
Unfortunately, if we have too many vectors it will fail and allocate
queues to vectors in a suboptimal manner. Change the condition check to
allow for excess vectors. In this case, the extras just won't be used.
Change-ID: I23e1e2955c64739c86612db88a25583e6a7e0b17
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a prefetch for the next Tx descriptor to be used when we know
there are more coming.
Change-ID: Ibb9acab11d508eec2db7da795df74debc16eeacb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Flex10 device/function capability has been upgraded to include
information needed to support Flex-10 configurations. This patch adds new
fields to the i40e_hw_capabilities structure and updates
i40e_parse_discover_capabilities functions to extract them from the AQ
response. Naming convention has changed to use flex10 mode instead of
existing mfp_mode_1.
Change-ID: I305dd888866985a30293acb3fb14fa43ca6b79ea
Signed-off-by: Pawel Orlowski <pawel.orlowski@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the driver can dynamically enable/disable FD ATR and SB features,
these stats help keep track of the current state and along with
fd_flush count provide a means to debug what could be going on
with the flow director filters. This will take away the need for
being verbose in our debug logs with respect to FD.
Change-ID: I29224f750fe6602391043655d18996570720377d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e supports UDP tunnel headers up to 80 bytes in length, so
this adds a check to ensure that it doesn't try to offload
packets that exceed that.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver will only configure as many queues as there are available
CPUs, up the maximum number of queues. However, it always configures
RSS as though it is using the maximum number of queues. This can cause
the device to drop a lot of RX traffic, as the packets get assigned to
nonfunctional queues.
Fix this by only configuring RSS with the number of active queues.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Down was requesting queue disables, but then exited immediately
without waiting for the queues to actually disable. This could
allow any function called after i40evf_down to run immediately,
including i40evf_up, and causes a memory leak.
Removing the whole reinit_locked function is the best way
to go about this, and allows for the driver to handle the
state changes by requesting reset from the periodic timer.
Also, add a couple WARN_ONs in slow path to help us recognize
if we re-introduce this issue or missed any cases.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SPT hardware does not require this driver workaround.
Removed the conditional that caused K1 workaround execution on SPT.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to clocking changes in the Skylake platform, there was i219
data corruption. To work around this, HW team reported the need
to increase the minimum gap between the PHY FIFO read and write pointers.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SPT/i219, there were CRC errors in speed 10/100 full duplex.
The solution given by the HW team is to increase the IPG from 8 to 0xC
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i219, there is a hardware bug that prevented ULP entry.
A side effect of the original software fix for this was that EEE in
Sx couldn't be enabled.
This patch implements a modified flow that allows both ULP and EEE in Sx.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On power up, the MAC - PHY interface needs to be set to PCIe, even if
cable is disconnected. In ME systems, the ME handles this on exit from
Sx state. In non-ME, the driver handles it. Added a check for non-ME
system to the driver code that handles that.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e_disable_aspm called pci_disable_link_state_locked which requires
pci_bus_sem to be held, but is also called from places where this semaphore
was not previously acquired. This patch implements two flavors of
disable_aspm, one that acquires the lock, and the other (_locked) which
should be called when the semaphore is already acquired.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version of igb to igb-5.2.18
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable IPv6 extension header processing as per hardware errata.
Also fix copyright date.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump. Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reviewing the code I noticed that one of the commits added an if
statement followed by a for loop, but the if statement was missing the
braces around the loop. This change corrects the coding style error.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a VF issues an LPORT_STATE request to enable a port that is already
enabled, the PF will first disable the VF LPORT. Then it should
re-enable the VF again with the new requested settings. This ensures
that any switch rules are cleared by deleting the LPORT on the switch.
However, the flow is bugged because we actually check if the VF is
enabled at the end, and thus don't re-enable it. Fix the flow so that we
actually clear the enabled flags as part of our removal of the LPORT.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The reference to err_no was left around after a previous code refactor.
We never use the value, and it doesn't seem to be used in side a hidden
macro reference. Discovered via cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SYSTIME_CFG.Adjust Direction bit is actually supposed to indicate
that the adjustment is positive. Fix the code to align correctly with
hardware and documentation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the __attribute__((packed)) indicator to some structures
which are overlayed onto a TLV message. These structures must be packed
as small as possible in order to correctly align when copied into the
mailbox buffer. Without doing so, the receiving mailbox code incorrectly
parses the values and we get invalid message responses from the switch
manager software.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During initialization, the VF counts its rings by walking the TQDLOC
registers. This works only if the TQMAP/RQMAP registers are set to map
all of the out-of-bound rings back to the first one. This allows the VF
to cleanly detect when it has run out of queues. Update the PF code so
that it resets the empty TQMAP/RQMAP registers post-VFLR to prevent
innocent VF drivers from triggering malicious driver events.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, we don't notify the switch at all when the PF
administratively sets a new VLAN or MAC address. This causes the old
addresses to remain valid on the switch table. Since the PF is
overriding any configuration done directly by the VF, we choose to
simply re-create the LPORT for the VF. This does mean that all rules for
the VF will be dropped when we set something directly via the PF, but it
prevents some weird issues where the MAC/VLAN table retains some stale
configuration.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
