Rationale: The differences between Falcon and Siena are in many ways larger
than those between Siena and EF10 (despite Siena being nominally "Falcon-
architecture"); for instance, Falcon has no MCPU, so there is no MCDI.
Removing Falcon support from the sfc driver should simplify the latter,
and avoid the possibility of Falcon support being broken by changes to sfc
(which are rarely if ever tested on Falcon, it being end-of-lifed hardware).
The sfc-falcon driver created in this changeset is essentially a copy of the
sfc driver, but with Siena- and EF10-specific code, including MCDI, removed
and with the "efx_" identifier prefix changed to "ef4_" (for "EFX 4000-
series") to avoid collisions when both drivers are built-in.
This changeset removes Falcon from the sfc driver's PCI ID table; then in
sfc I've removed obvious Falcon-related code: I removed the Falcon NIC
functions, Falcon PHY code, and EFX_REV_FALCON_*, then fixed up everything
that referenced them.
Also, increment minor version of both drivers (to 4.1).
For now, CONFIG_SFC selects CONFIG_SFC_FALCON, so that updating old configs
doesn't cause Falcon support to disappear; but that should be undone at
some point in the future.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool's '-r' command. Restarting
N-WAY negotiation can be useful to activate newly changed EEE
settings etc.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to query and set Energy Efficient Ethernet parameters
via ethtool for applicable devices.
This patch doesn't activate full EEE support in cpsw driver, but it
enables reading and writing EEE advertising settings. This way one
can disable advertising EEE for certain speeds.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Rami Rosen <roszenrami@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we change MTU or the number of channels on a netvsc device we get the
following logged:
hv_netvsc bf5edba8...: net device safe to remove
hv_netvsc: hv_netvsc channel opened successfully
hv_netvsc bf5edba8...: Send section size: 6144, Section count:2560
hv_netvsc bf5edba8...: Device MAC 00:15:5d:1e:91:12 link state up
This information is useful as debug at most.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We call bus->init() before allocating 'lag.mapping'. Change the order of
operations in removal path to reflect that.
This makes the error path of mlxsw_core_bus_device_register() symmetric
with mlxsw_core_bus_device_unregister().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this rollback, the thermal zone is still registered during the
error path, whereas its private data is freed upon the destruction of
the underlying bus device due to the use of devm_kzalloc(). This results
in use after free.
Fix this by calling mlxsw_thermal_fini() from the appropriate place in
the error path.
Fixes: a50c1e3565 ("mlxsw: core: Implement thermal zone")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shared buffer pools are containers whose size is used to calculate
the maximum usage for packets from / to a specific port / {port, PG/TC},
when dynamic threshold is employed.
While it's perfectly fine for the sum of the pools to exceed the maximum
size of the shared buffer, a single pool cannot.
Add a check when the pool size is set and forbid sizes larger than the
maximum size of the shared buffer.
Without the patch:
$ devlink sb pool set pci/0000:03:00.0 pool 0 size 999999999 thtype
dynamic
// No error is returned
With the patch:
$ devlink sb pool set pci/0000:03:00.0 pool 0 size 999999999 thtype
dynamic
devlink answers: Invalid argument
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be able to limit the size of shared buffer pools, so query
the maximum size from the device during init.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added switchib driver fails to link if MLXSW_PCI=m:
drivers/net/ethernet/mellanox/mlxsw/mlxsw_switchib.o: In function^Cmlxsw_sib_module_exit':
switchib.c:(.exit.text+0x8): undefined reference to `mlxsw_pci_driver_unregister'
switchib.c:(.exit.text+0x10): undefined reference to `mlxsw_pci_driver_unregister'
drivers/net/ethernet/mellanox/mlxsw/mlxsw_switchib.o: In function `mlxsw_sib_module_init':
switchib.c:(.init.text+0x28): undefined reference to `mlxsw_pci_driver_register'
switchib.c:(.init.text+0x38): undefined reference to `mlxsw_pci_driver_register'
switchib.c:(.init.text+0x48): undefined reference to `mlxsw_pci_driver_unregister'
The other two such sub-drivers have a dependency, so add the same one
here. In theory we could allow this driver if MLXSW_PCI is disabled,
but it's probably not worth it.
Fixes: d1ba526384 ("mlxsw: switchib: Introduce SwitchIB and SwitchIB silicon driver")
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device_release_driver(&phydev->mdio.dev) is called, it releases all
resources belonging to the PHY device. Hence the subsequent call to
phy_led_triggers_unregister() will access already freed memory when
unregistering the LEDs.
Move the call to phy_led_triggers_unregister() before the possible call
to device_release_driver() to fix this.
Fixes: 2e0bc452f4 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix comments, add some new, and make debugfs output consistent.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to disable EEE advertisement in the generic PHY
by providing a mask of prohibited modes corresponding to the value found in
the MDIO_AN_EEE_ADV register.
On some platforms, PHY Low power idle seems to be causing issues, even
breaking the link some cases. The patch provides a convenient way for these
platforms to disable EEE advertisement and work around the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac4 IP can synthesized with 1-8 number of tx queues.
On an IP synthesized with DWC_EQOS_NUM_TXQ > 1, all txqueues are disabled
by default. For these IPs, the bitfield TXQEN is R/W.
Always enable tx queue 0. The write will have no effect on IPs synthesized
with DWC_EQOS_NUM_TXQ == 1.
The driver does still not utilize more than one tx queue in the IP.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dependencies on the architectures that support these devices and
add compile test to ensure ongoing code build coverage.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 stats are chaotic because a deferred work queue is responsible
to update them every 250 ms.
Even sampling stats every one second with "sar -n DEV 1" gives
variations like the following :
lpaa23:~# sar -n DEV 1 10 | grep eth0 | cut -c1-65
07:39:22 eth0 146877.00 3265554.00 9467.15 4828168.50
07:39:23 eth0 146587.00 3260329.00 9448.15 4820445.98
07:39:24 eth0 146894.00 3259989.00 9468.55 4819943.26
07:39:25 eth0 110368.00 2454497.00 7113.95 3629012.17 <<>>
07:39:26 eth0 146563.00 3257502.00 9447.25 4816266.23
07:39:27 eth0 145678.00 3258292.00 9389.79 4817414.39
07:39:28 eth0 145268.00 3253171.00 9363.85 4809852.46
07:39:29 eth0 146439.00 3262185.00 9438.97 4823172.48
07:39:30 eth0 146758.00 3264175.00 9459.94 4826124.13
07:39:31 eth0 146843.00 3256903.00 9465.44 4815381.97
Average: eth0 142827.50 3179259.70 9206.30 4700578.16
This patch allows rx/tx bytes/packets counters being folded at the
time we need stats.
We now can fetch stats every 1 ms if we want to check NIC behavior
on a small time window. It is also easier to detect anomalies.
lpaa23:~# sar -n DEV 1 10 | grep eth0 | cut -c1-65
07:42:50 eth0 142915.00 3177696.00 9212.06 4698270.42
07:42:51 eth0 143741.00 3200232.00 9265.15 4731593.02
07:42:52 eth0 142781.00 3171600.00 9202.92 4689260.16
07:42:53 eth0 143835.00 3192932.00 9271.80 4720761.39
07:42:54 eth0 141922.00 3165174.00 9147.64 4679759.21
07:42:55 eth0 142993.00 3207038.00 9216.78 4741653.05
07:42:56 eth0 141394.06 3154335.64 9113.85 4663731.73
07:42:57 eth0 141850.00 3161202.00 9144.48 4673866.07
07:42:58 eth0 143439.00 3180736.00 9246.05 4702755.35
07:42:59 eth0 143501.00 3210992.00 9249.99 4747501.84
Average: eth0 142835.66 3182165.93 9206.98 4704874.08
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It shold reserved sizeof(ipv6hdr) for geneve in ipv6 tunnel.
Fixes: c3ef5aa5e5 ('geneve: Merge ipv4 and ipv6 geneve_build_skb()')
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g1_irq_setup() sets up chip->g1_irq.nirqs interrupt mappings,
so free the same amount. This will be 8 or 9 in practice, less than 16.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user can now override the automatic driver decision using the
rx_cqe_compress flag, which is the preference for CQE compression.
The flag is initialized with the automatic driver decision.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pflags is a configuration parameter for the netdev, naturally it belongs
to priv->params.
Also introduce MLX5E_GET_PFLAG
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the self diagnostic tests to support loopback test.
The loopback test doesn't require the offline flag, it will use the
generic dev_queue_xmit and a dedicated packet_type to capture and verify
mlx5e selftest loopback packets.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The self diagnostics test implementaion include the following features:
1. Link Test: Check that link is in up state.
2. Speed Test: Check that link was negotiated correctly.
3. Health Test: Check the device health.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setdcbx interface to set the DCBX mode to firmware or os.
If setdcbx is called with mode value of zero, the DCBX mode
is set to firmware.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DBCX by default is controlled by firmware where dcbx capability bit
is set. In this mode, firmware is responsible for reading/sending the
TLV packets from/to the remote partner.
This patch sets up the infrastructure to move between HOST/FW DCBX
control mode.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add set/query commands for DCBX_PARAM register
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue description:
Current implementation saves the ETS settings from user in
a temporal soft copy and returns this settings when user
queries the ETS settings.
With the new DCBX firmware, the ETS settings can be changed
by firmware when the DCBX is in firmware controlled mode. Therefore,
user will obtain wrong values from the temporal soft copy.
Solution:
1. Read the ETS settings directly from firmware.
2. For tc_tsa:
a. Initialize tc_tsa to vendor IEEE_8021QAZ_TSA_VENDOR at netdev
creation.
b. When reading ETS setting from FW, if the traffic class bandwidth
is less than 100, set tc_tsa to IEEE_8021QAZ_TSA_ETS. This
implementation solves the scenarios when the DCBX is in FW control
and willing bit is on which means the ETS setting is dictated
by remote switch.
Also check ETS capability where needed.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DCBX CEE API interface for ConnectX-4. Configurations are stored in
a temporary structure and are applied to the card's firmware when
the CEE's setall callback function is called.
Note:
priority group in CEE is equivalent to traffic class in ConnectX-4
hardware spec.
bw allocation per priority in CEE is not supported because ConnectX-4
only supports bw allocation per traffic class.
user priority in CEE does not have an equivalent term in ConnectX-4.
Therefore, user priority to priority mapping in CEE is not supported.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure firmware supports qos before exposing the DCB API.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use single queue even if multiqueue is enabled and let admin to
enable it through ethtool later. This is used to avoid possible
regression (small packet TCP stream transmission). But looks like an
overkill since:
- single queue user can disable multiqueue when launching qemu
- brings extra troubles for the management since it needs extra admin
tool in guest to enable multiqueue
- multiqueue performs much better than single queue in most of the
cases
So this patch enables multiqueue by default: if #queues is less than or
equal to #vcpu, enable as much as queue pairs; if #queues is greater
than #vcpu, enable #vcpu queue pairs.
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Cc: Jeremy Eder <jeder@redhat.com>
Cc: Marko Myllynen <myllynen@redhat.com>
Cc: Maxime Coquelin <maxime.coquelin@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing comment for the MV88E6097 because of unification.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing definition of g1_irqs for MV88E6097.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since long already bpf_func is not only about struct sk_buff * as
input anymore. Make it generic as void *, so that callers don't
need to cast for it each time they call BPF_PROG_RUN().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use ->heap_buf after commit 46d1efd852 ("sfc: remove Software
TSO") so let's remove the last traces.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch depends on commit d8d2635419 ("ptp: Introduce a high
resolution frequency adjustment method.")
The gianfar devices offer a frequency resolution of about 0.46 ppb
(depends on actual value of tmr_add, for the calculation assumed
0x80000000). This patch lets users of the device benefit from the increased
frequency resolution when tuning the clock. Thanks to the rounding the
maximum error between the requested frequency and the applied frequency
will then be about 0.23 ppb.
Tested on a v3.3.8 kernel on a real gianfar device. Verified compilation
on net-next (currently at v4.9-rc5).
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per RX ring packets/bytes counters are not protected by global
priv->stats_lock.
Better not confuse the reader, and use READ_ONCE() to show we read
these counters without surrounding synchronization.
Interrupt moderation is best effort, and we do not really care of
ultra precise counters.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure policers and connect them to trap groups.
While many trap groups share policer's configuration they don't share
the actual policer because each trap group represents a different
flow / protocol and we don't want one of them to be able to exceed its
rate on behalf of another.
For example, if STP and LLDP gets to send 128 packets/sec each, if we
put them in one 256 packets/sec policer, one can send 200 packets while
the other only 50.
Note that IP2ME covers lots of flows, so it's limit is set to match the
cpu ability to handle data.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QPCR register is used to create and control policers.
A policer can discard or change the color of packets that are
trapped by a specific trap.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new resource to resources query: max cpu policers which tells us how
many policers can be used to limit the data rate to the cpu port.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups can be used to control traps priority, both in terms of
which trap "wins" if a packet matches two traps (priority) and in terms
of packets from which trap group will be scheduled to the cpu first (tc).
They can also be used to set rate limiters (policers) on them (will be
added in the next patches).
Currently, we support two trap groups. In Spectrum we want a better
resolution, so every protocol / flow will have a different trap group,
so we can control its parameters separately. Once the policers will be
implemented, it will also allow us limit the rate of each protocol by
itself.
This patch change the trap group list to include:
* the emad trap group, which is shared for all the devices.
* Switchx2's trap groups, which are a copy of the current trap groups.
* Spectrum's new trap groups, in order to match the above guidelines.
(Switchib is using only the emad trap group, so it require no changes).
This patch also includes new configuration for Spectrum's trap groups,
with primary priority order within them.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a trap for BGP protocol that was previously trapped by the generic trap
for IP2ME. This trap will allow us to have better control (over priority
and rate) of the traffic.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups have many options which we currently set to default values.
In the next patches we will use many of them with non-default values.
Some of these options have no default value, so this patch sets them as
params for the trap group set function. Others almost always use the same
values, so the set function will use this default values. In the rare cases
when they will need to be with other values, these values can be set
directly (using the macros for fields in registers).
Parameters without default value:
TC - the traffic class for packets that hit this trap group.
(old default is the max tc)
priority - if one packet hits multiple trap groups, the group with the
higher priority will "catch" it. (old default is 0)
policer - limit rate policer (old default is disabled)
Default parameters:
swid - switch id, relevant for the emad trap only, ignored on Spectrum.
(new default is 0)
rdq - CPU receive descriptor queue (new default is identical to trap
group id)
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the max number of trap groups to resource query.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the emad trap init was done in the core. In the future we will
want to add some changes to the traps groups, according to device type.
This commit create a driver function to create the trap group for the
emad, so later it can be changed by devices. It also changes the emad
registration to use the new generic functions.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we set the trap group to pre-determined option, based on whether
it is an rx or event trap.
This commit adds a possibility to chose the trap group, so it can be set
to different values in the following patches.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change trap setting function so instead of determining the trap group by
trap id, it gets it as a parameter (so later we can have different trap
groups for Spectrum and Switchx2).
Add "is_ctrl" parameter to the trap setting function. It control whether
the trapped packets wait in a designated control buffer or in their
default one. This parameter is ignored by Switchx2 and Switchib.
Add these parameters to the traps array in Spectrum, Switchx2 and
Switchib.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the event handling in Switchib to be comptible with Spectrum and
Switchx2.
Use the generic listener struct for the events. Init and fini them by loop
(and not by calling each event by its name).
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the events to use the generic listener struct.
Merge the event list into the trap list, so the same functions will
handle both.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the events to use the generic listener struct.
Merge the event list into the trap list, so the same functions will
handle both.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a macro for creating the generic listener struct for events,
similar to the one for rx traps.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
