DSI panels can always be hotplugged via the DSI bus' attach/detach
infrastructure, so unconditionally mark the connector hotpluggable.
While at it, also make sure that when a panel is detached the connector
is marked unconnected before calling into the DRM hotplug helpers to
reflect the correct state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The common clock framework will take care of preparing and enabling the
parent of the DSI clock automatically.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for supporting command mode panels, don't disable the
clock when the output is disabled. The output will be enabled only after
the panel has been programmed in command mode, so the clock must always
remain on.
As a side-effect, pad calibration now only needs to be done at driver
probe time, since neither power nor controller state will go away before
driver removal. While at it, use a 32-bit variable to store register
content because the registers are 32-bit even on 64-bit Tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than hardcoding them as macros, make the host and video FIFO
depths parameters so that they can be more easily adjusted if a new
generation of the Tegra SoC changes them.
While at it, set the depth of the video FIFO to the correct value of
1920 *words* rather than *bytes*.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the panel and output were only enabled on encoder->dpms(). If
userspace called dpms on before doing a modeset, the driver would get into
a state where the connector had a dpms state of ON, but the encoder and output
were not enabled (because the encoder is not yet attached to the connector).
Subsequent dpms ON calls are ignored b/c the connector's state already matches
the desired state.
This patch enables/disables the panel and output on modeset as well, so we
can catch the above case.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both display controllers are in their own power partition. Currently the
driver relies on the assumption that these partitions are on (which is
the hardware default). However some bootloaders may disable them, so the
driver must make sure to turn them back on to avoid hangs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The introduction of the COMPILE_TEST dependency in commit 158b50aefa
(drm/tegra: Increase compile test coverage) removes the dependency on
COMMON_CLK (implicitly selected via ARCH_TEGRA, ARCH_MULTI_V7 and
ARCH_MULTIPLATFORM).
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the CRTC is enabled, make sure the VBLANK machinery is enabled.
Failure to do so will cause drm_vblank_get() to not enable the VBLANK on
the CRTC and VBLANK-synchronized page-flips won't work.
While at it, get rid of the legacy drm_vblank_pre_modeset() and
drm_vblank_post_modeset() calls that are replaced by drm_vblank_on()
and drm_vblank_off().
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Just a bit of OCD cleanup on headers - this function isn't the core
interface any more but just a helper for drivers who haven't yet
transitioned to universal planes. Put the declaration at the right
spot and sprinkle necessary #includes over all drivers.
Maybe this helps to encourage driver maintainers to do the switch.
v2: Fix #include ordering for tegra, reported by 0-day builder.
v3: Include required headers, reported by Thierry.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
v2: Don't forget git add, noticed by David.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rename the defines to have levels instead of values for vswing and
pre-emph levels as the values may differ in other scenarios like low vswing of
eDP1.4 where the values are different.
Done using following cocci patch for each define:
@@
@@
# define DP_TRAIN_VOLTAGE_SWING_400 (0 << 0)
+ # define DP_TRAIN_VOLTAGE_SWING_LEVEL_0 (0 << 0)
...
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
Mostly some cleanup all over the place. Pitch alignment limitations of
the display controller are now honored and job submission is 64-bit
safe.
The SOR output (used for eDP) properly configures sync signal polarities
according to the display mode rather than hard-coding them to some value
and the number of bits per color is now taken from the panel rather than
hard-coded to properly support 24-bit vs. 18-bit panels.
The DSI controller now properly supports non-continuous clock mode.
GEM objects can now have their flags and tiling mode modified via IOCTLs
to allow buffers imported from Nouveau to be properly displayed. Newer
generations of the Tegra display controller can also detile block linear
buffers at scan-out time.
Finally the driver now properly exports MODULE_DEVICE_TABLEs to allow it
to be automatically loaded when built as a module.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qYgE
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.17-rc1
Mostly some cleanup all over the place. Pitch alignment limitations of
the display controller are now honored and job submission is 64-bit
safe.
The SOR output (used for eDP) properly configures sync signal polarities
according to the display mode rather than hard-coding them to some value
and the number of bits per color is now taken from the panel rather than
hard-coded to properly support 24-bit vs. 18-bit panels.
The DSI controller now properly supports non-continuous clock mode.
GEM objects can now have their flags and tiling mode modified via IOCTLs
to allow buffers imported from Nouveau to be properly displayed. Newer
generations of the Tegra display controller can also detile block linear
buffers at scan-out time.
Finally the driver now properly exports MODULE_DEVICE_TABLEs to allow it
to be automatically loaded when built as a module.
* tag 'drm/tegra/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: add MODULE_DEVICE_TABLEs
drm/tegra: dc - Reset controller on driver remove
drm/tegra: Properly align stride for framebuffers
drm/tegra: sor - Configure proper sync polarities
drm/tegra: sor - Use bits-per-color from panel
drm/tegra: Make job submission 64-bit safe
drm/tegra: Allow non-authenticated processes to create buffer objects
drm/tegra: Add SET/GET_FLAGS IOCTLs
drm/tegra: Add SET/GET_TILING IOCTLs
drm/tegra: Implement more tiling modes
drm/tegra: dsi - Handle non-continuous clock flag
drm/tegra: sor - missing unlock on error
Panels can now be more finely controlled via .prepare() and .unprepare()
callbacks in addition to .enable() and .disable(). New kerneldoc details
what they are supposed to do and when they should be called.
The simple panel driver gained support for a couple of new panels and it
is now possible to specify additional delays during power up and power
down sequences if panels require it.
DSI devices can now advertise that they support non-continuous clock
mode which will allow DSI host controllers to disable the high speed
clock after transmissions to save power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vf7m
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v3.17-rc1
Panels can now be more finely controlled via .prepare() and .unprepare()
callbacks in addition to .enable() and .disable(). New kerneldoc details
what they are supposed to do and when they should be called.
The simple panel driver gained support for a couple of new panels and it
is now possible to specify additional delays during power up and power
down sequences if panels require it.
DSI devices can now advertise that they support non-continuous clock
mode which will allow DSI host controllers to disable the high speed
clock after transmissions to save power.
* tag 'drm/panel/for-3.17-rc1' of git://anongit.freedesktop.org/tegra/linux: (30 commits)
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
drm/panel: simple: Add Innolux N116BGE panel support
...
Modify tegra output driver to support the new panel calls:
prepare and unprepare.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When tegra-drm.ko is built as a module, these MODULE_DEVICE_TABLEs allow
the module to be auto-loaded since the module will match the devices
instantiated from device tree.
(Notes for stable: in 3.14+, just git rm any conflicting file, since they
are added in later kernels. For 3.13 and below, manual merging will be
needed)
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since the device will no longer be used, may as well keep it in reset to
potentially save some power and make sure it is in a clean state the
next time it's probed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra20 and Tegra30 both required the buffer line stride to be aligned
on 8 byte boundaries. Tegra114 and Tegra124 increased the alignment to
64 bytes. Introduce a parameter to specify the alignment requirements
for each display controller and round up the pitch of newly allocated
framebuffers appropriately.
Originally-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This change uses the value of bits-per-color from panel to remove one
more hardcoded value.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Job submission currently relies on the fact that struct drm_tegra_reloc
and struct host1x_reloc are the same size and uses a simple call to the
copy_from_user() function to copy them to kernel space. This causes the
handle to be stored in the buffer object field, which then needs a cast
to a 32 bit integer to resolve it to a proper buffer object pointer and
store it back in the buffer object field.
On 64-bit architectures that will no longer work, since pointers are 64
bits wide whereas handles will remain 32 bits. This causes the sizes of
both structures to because different and copying will no longer work.
Fix this by adding a new function, host1x_reloc_get_user(), that copies
the structures field by field.
While at it, use substructures for the command and target buffers in
struct host1x_reloc for better readability. Also use unsized types to
make it more obvious that this isn't part of userspace ABI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This matches what other drivers do for equivalent IOCTLs.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM_TEGRA_GEM_SET_FLAGS IOCTL can be used to set the flags of a
buffer object after it has been allocated or imported. Flags associated
with a buffer object can be queried using the DRM_TEGRA_GEM_GET_FLAGS
IOCTL.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the tiling parameters of buffer objects can only be set at
allocation time, and only a single tiled mode is supported. This new
DRM_TEGRA_GEM_SET_TILING IOCTL allows more modes to be set and also
allows the tiling mode to be changed after the allocation. This will
enable the Tegra DRM driver to import buffers from a GPU and directly
scan them out by configuring the display controller appropriately.
To complement this, the DRM_TEGRA_GEM_GET_TILING IOCTL can query the
current tiling mode of a buffer object. This is necessary when importing
buffers via handle (as is done in Mesa for example) so that userspace
can determine the proper parameters for the 2D or 3D engines.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 supports a block-linear mode in addition to the regular pitch
linear and tiled modes. Add support for these by moving the internal
representation into a structure rather than a simple flag.
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Handle the MIPI_DSI_CLOCK_NONCONTINUOUS flag and only set TX-only
clock behavior when this flag is present to allow panels requiring
continuous clock mode to operate with this driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We should unlock before returning the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit converts the PMC support code to a platform driver. Because
the boot process needs to call into this driver very early, also set up
a minimal environment via an early initcall.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to not clutter the include/linux directory with SoC specific
headers, move the Tegra-specific headers out into a separate directory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This allows reservation objects to be used in dma-buf. it's required
for implementing polling support on the fences that belong to a dma-buf.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com> #drivers/media/v4l2-core/
Acked-by: Thomas Hellstrom <thellstrom@vmware.com> #drivers/gpu/drm/ttm
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> #drivers/gpu/drm/armada/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race condition currently exists on Tegra, where it can happen that a
monitor attached via HDMI isn't detected during the initial FB helper
setup, but the hotplug event happens too early to be processed by the
poll helpers because they haven't been initialized yet. This happens
because on some boards the HDMI driver can control the regulator that
supplies the +5V pin on the HDMI connector. Therefore depending on the
timing between the initialization of the HDMI driver and the rest of
DRM, it's possible that the monitor returns the hotplug signal right
within the window where we would miss it.
Unfortunately, drm_kms_helper_poll_init() will wreak havoc when called
before at least some parts of the FB helpers have been set up.
This commit fixes this by splitting out the minimum of initialization
required to make drm_kms_helper_poll_init() work into a separate
function that can be called early. It is then safe to move all of the
poll helper initialization to an earlier point in time (before the
HDMI output driver has a chance to enable the +5V supply). That way if
the hotplug signal is returned before the initial FB helper setup, the
monitor will be forcefully detected at that point, and if the hotplug
signal is returned after that it will be properly handled by the poll
helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To implement hotplug detection in a race-free manner, drivers must call
drm_kms_helper_poll_init() before hotplug events can be triggered. Such
events can be triggered right after any of the encoders or connectors
are initialized. At the same time, if the drm_fb_helper_hotplug_event()
helper is used by a driver, then the poll helper requires some parts of
the FB helper to be initialized to prevent a crash.
At the same time, drm_fb_helper_init() requires information that is not
necessarily available at such an early stage (number of CRTCs and
connectors), so it cannot be used yet.
Add a new helper, drm_fb_helper_prepare(), that initializes the bare
minimum needed to allow drm_kms_helper_poll_init() to execute and any
subsequent hotplug events to be processed properly.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no need for this to be modifiable. Make it const so that it can
be put into the .rodata section.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to the DP specification the disparity of the first symbol
should always be negative. It is therefore safe to assume that panels
will conform to that and therefore parameterizing this field should
never be necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The number of HBLANK and VBLANK symbols can be computed at runtime so
that they can be set appropriately depending on the video mode and DP
link.
These values are used by the packet generation logic to determine how
many audio samples can be transferred during the blanking intervals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The currently hardcoded link parameters don't work on all eDP panels, so
compute the parameters at runtime depending on the mode and panel type
to allow the driver to cope with a wider variety of panels.
Note that the number of bits per pixel of the panel is still hardcoded,
but this can be addressed in a separate patch.
This is largely based on a patch by Stéphane Marchesin but the algorithm
was largely rewritten to be more readable and concise.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Lanes are powered up in decreasing order. Power them down in increasing
order for consistency.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The comment above mentions link A/B but this isn't what the code does,
so let's fix that.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The code currently rounds up the clock to the next MHZ, which is
rounding up a 69.5MHz clock to 70MHz on my machine. This in turn
prevents the display from syncing. Removing this rounding fixes eDP
for me.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Other output drivers set up debugfs slightly differently. Bring the SOR
driver in line with those for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Removing only the root directory will fail when there are still files in
it. Instead of manually removing all files, remove the whole directory
recursively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Doing so allows the hotplug events generated by the connector to be
properly handled by the DRM poll helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Calling the drm_helper_hpd_irq_event() helper can sleep, so instead of
invoking it directly from the interrupt handler, schedule a work queue
and run it from there.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable hardware cursor support on Tegra124. Earlier generations support
the hardware cursor to some degree as well, but not in a way that can be
generically exposed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core can now cope with drivers that don't have an associated
struct drm_bus, so the host1x implementation is no longer useful.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 is mostly backwards-compatible with Tegra114. However, Tegra124
supports a few more features (e.g. interlacing, ...). Introduce a new
compatible string and TMDS tables to cope with these differences.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Accessing the CRC debugfs file will hang the system if the SOR is not
enabled, so make sure that it is stays enabled until the CRC has been
read.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In some cases the pixel clock used to not be correct, which is why it
had to be recomputed. It turns out that the reason why it wasn't correct
is that it was used wrongly. If used correctly there's not need for the
recomputation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The shift clock divider is highly dependent on the type of output, so
push computation of it down into the output drivers. The old code used
to work merely by accident.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Program the shift clock divider in tegra_crtc_setup_clk() since that's
where the divider is computed, so passing it around can be avoided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assert the DSI controller's reset when the driver is unloaded to reduce
power consumption and to put the controller into a known state for
subsequent driver reloads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
To prevent the enable or disable operations to potentially be run
multiple times, add guards to return early when the output is already
in the targetted state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The packet sequencer needs to be programmed depending on the video mode
of the attached peripheral. Add support for non-burst video modes with
sync events (as opposed to sync pulses) and select either sequence
depending on the video mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI controllers are powered by a (typically 1.2V) regulator. Usually
this is always on, so there was no need to support enabling or disabling
it thus far. But in order not to consume any power when DSI is inactive,
give the driver a chance to enable or disable the supply as needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A bunch of registers are initialized to 0 upon during driver probe. It
turns out that none of these are actually needed, so they can simply be
dropped.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The pixel format enumeration values used by the Tegra DSI controller
don't match those defined by the DSI framework. Make sure to convert
them to the internal format before writing it to the register.
Signed-off-by: Thierry Reding <treding@nvidia.com>
For some reason when the PW*_ENABLE and PM*_ENABLE fields are cleared
during disable, the HDMI output stops working properly. Resetting and
initializing doesn't help.
Comment out those accesses for now until it has been determined what to
do about them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Disable LVDS mode according to register documentation. It seems like
this has no effect on the operation of HDMI, but it's probably a good
idea to do this anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reflects the power-up sequence as described in the documentation,
but it doesn't seem to be strictly necessary to get HDMI to work.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clocks are never enabled or disabled in atomic context, so we can use
the clk_prepare_enable() and clk_disable_unprepare() helpers instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The generic Tegra output code already sets up the clocks properly, so
there's no need to do it again when the HDMI output is enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Revert commit 18ebc0f404 "drm/tegra: hdmi: Enable VDD earlier for
hotplug/DDC" and instead add a new supply for the +5V pin on the HDMI
connector.
The vdd-supply property refers to the regulator that supplies the
AVDD_HDMI input on Tegra, rather than the +5V HDMI connector pin. This
was never a problem before, because all boards had that pin hooked up to
a regulator that was always on. Starting with Dalmore and continuing
with Venice2, the +5V pin is controllable via a GPIO. For reasons
unknown, the GPIO ended up as the controlling GPIO of the AVDD_HDMI
supply in the Dalmore and Venice2 DTS files. But that's not correct.
Instead, a separate supply must be introduced so that the +5V pin can be
controlled separately from the supplies that feed the HDMI block within
Tegra.
A new hdmi-supply property is introduced that takes the place of the
vdd-supply and vdd-supply is only enabled when HDMI is enabled rather
than all the time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Setting the bits in this register is dependent on the output type driven
by the display controller. All output drivers already set these properly
so there is no need to do it here again.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The tegra_dc_format() and tegra_dc_setup_window() functions are only
used internally by the display controller driver. Move them upwards in
order to make them static and get rid of the function prototypes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
V_DIRECTION is the name of the field in the documentation, so use that
for consistency. Also add the H_DIRECTION field for completeness.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR allows the computation of a 32 bit CRC of the content that it
transmits. This functionality is exposed via debugfs and is useful to
verify proper operation of the SOR.
Signed-off-by: Thierry Reding <treding@nvidia.com>
YUYV is UYVY with swapped bytes. Luckily the Tegra DC hardware can swap
bytes during scan-out, so supporting YUYV is simply a matter of writing
the correct value to the byteswap register.
This patch modifies tegra_dc_format() to return the byte swap parameter
via an output parameter in addition to returning the pixel format. Many
other formats can potentially be supported in a similar way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove extern keyword from function prototypes since it isn't needed and
drop an unnecessary forward declaration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
All drm_fb_helper_restore_fbdev_mode() call sites, save one, do the same
locking. Simplify this into drm_fb_helper_restore_fbdev_mode_unlocked().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should avoid races between connector probing and HPD
irqs in the future, currently mode_config.mutex blocks this
possibility.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Next pull request, this time more of the drm de-midlayering work. The big
thing is that his patch series here removes everything from drm_bus except
the set_busid callback. Thierry has a few more patches on top of this to
make that one optional to.
With that we can ditch all the non-pci drm_bus implementations, which
Thierry has already done for the fake tegra host1x drm_bus.
Reviewed by Thierry, Laurent and David and now also survived some testing
on my intel boxes to make sure the irq fumble is fixed correctly ;-) The
last minute rebase was just to add the r-b tags from Thierry for the 2
patches I've redone.
* 'drm-init-cleanup' of git://people.freedesktop.org/~danvet/drm:
drm/<drivers>: don't set driver->dev_priv_size to 0
drm: Remove dev->kdriver
drm: remove drm_bus->get_name
drm: rip out dev->devname
drm: inline drm_pci_set_unique
drm: remove bus->get_irq implementations
drm: pass the irq explicitly to drm_irq_install
drm/irq: Look up the pci irq directly in the drm_control ioctl
drm/irq: track the irq installed in drm_irq_install in dev->irq
drm: rename dev->count_lock to dev->buf_lock
drm: Rip out totally bogus vga_switcheroo->can_switch locking
drm: kill drm_bus->bus_type
drm: remove drm_dev_to_irq from drivers
drm/irq: remove cargo-culted locking from irq_install/uninstall
drm/irq: drm_control is a legacy ioctl, so pci devices only
drm/pci: fold in irq_by_busid support
drm/irq: simplify irq checks in drm_wait_vblank
A single fix for some framebuffer reference counting fallout caused by
the primary plane helpers introduced in 3.15-rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=uM53
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.15-rc3' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Fixes for v3.15-rc3
A single fix for some framebuffer reference counting fallout caused by
the primary plane helpers introduced in 3.15-rc1.
* tag 'drm/tegra/for-3.15-rc3' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: restrict plane loops to legacy planes
In Matt Ropers primary plane series a set of prep patches like
commit af2b653bfb
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Apr 1 15:22:32 2014 -0700
drm/i915: Restrict plane loops to only operate on overlay planes (v2)
ensured that all exisiting users of the mode_config->plane_list
wouldn't change behaviour. Unfortunately tegra seems to have fallen
through the cracks. Fix it.
This regression was introduced in
commit e13161af80
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Apr 1 15:22:38 2014 -0700
drm: Add drm_crtc_init_with_planes() (v2)
The result was that we've unref'ed the fb for the primary plane twice,
leading to a use-after free bug. This is because the drm core will
already set crtc->primary->fb to NULL and do the unref for us, and the
crtc disable hook is called by the drm crtc helpers for exactly this
case.
Aside: Now that the fbdev helpers clean up planes there's no longer a
need to do this in drivers. So this could probably be nuked entirely
in linux-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This was only ever used to pretty-print the irq driver name. And on
kms systems due to set_version bonghits we never set up the prettier
name, ever. Which make this a bit pointless.
Also, we can always dig out the driver-instance/irq relationship
through other means, so this isn't that useful. So just rip it out to
simplify the set_version/set_busid insanity a bit.
Also delete the temporary busname from drm_pci_set_busid, it's now
unused.
v2: Rebase on top of the new host1x drm_bus for tegra.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Completely unused. Hooray, midlayer mistakes that didn't cause work to
undo!
v2: Rebase on top of the recent tegra changes which added a host1x drm
bus.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Certain types of I2C-over-AUX transactions require that only the address
is transferred. Detect this by looking at the AUX message's size and set
the address-only bit appropriately.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement eDP support for Tegra124 and support the PRIME vmap()/vunmap()
operations.
A symbol that is required for upcoming V4L2 support is now exported by
the host1x driver.
Relicense drivers under the GPL v2 for consistency. One exception is the
public header file, which is relicensed under MIT to abide by the common
rule.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=LGu0
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.15-rc1
Implement eDP support for Tegra124 and support the PRIME vmap()/vunmap()
operations.
A symbol that is required for upcoming V4L2 support is now exported by
the host1x driver.
Relicense drivers under the GPL v2 for consistency. One exception is the
public header file, which is relicensed under MIT to abide by the common
rule.
* tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Use standard GPL v2 license text
drm/tegra: Relicense under GPL v2
drm/tegra: Relicense public header under MIT
drm/tegra: Add eDP support
gpu: host1x: export host1x_syncpt_incr_max() function
drm/tegra: prime: Add vmap support
Use the more canonical and concise variant of the GPL v2 license text.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The majority of the code in this driver is licensed under the GPL v2, so
relicense the rest under GPL v2 as well for consistency.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTJlUvAAoJEHm+PkMAQRiGOhYH/1I+Bc7N7Rjr6QQAtBIy0GPC
XMqSE/gpgxlvRneQbQsvTUlPnWRhgzLGendT9HFKawkaQ0UNuZdRVyBHGFmpuED8
RlbicVVuuEZabrxEnCd7UPvYvEyK5pLIFpCRs5B+ManB1qLki2Ar03ymH1NRxOde
edmPbSUFo2aONITrEBm7tqT3cShTmBaDGP/zU0TNDMNrpVVDbHZolSNu2z4xOTa5
GqAOEbluLQ6jP3yxWur/V3Lk3W7pB6TabfX4o6UZu0F3iFnJxRMIzHXrI3o4yLTj
HEwmB3npfc8DIUk4oik7RkN+aqxDcdg/rBLQD63+xxt6zCkP+0q16brC0R67qWE=
=n9Ml
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc7' into drm-next
Linux 3.14-rc7
Backmerge to help out Intel guys.
Lets not trick ourselves into thinking "drm_device" objects are not
ref-counted. That's just utterly stupid. We manage "drm_minor" objects on
each drm-device and each minor can have an unlimited number of open
handles. Each of these handles has the drm_minor (and thus the drm_device)
as private-data in the file-handle. Therefore, we may not destroy
"drm_device" until all these handles are closed.
It is *not* possible to reset all these pointers atomically and restrict
access to them, and this is *not* how this is done! Instead, we use
ref-counts to make sure the object is valid and not freed.
Note that we currently use "dev->open_count" for that, which is *exactly*
the same as a reference-count, just open coded. So this patch doesn't
change any semantics on DRM devices (well, this patch just introduces the
ref-count, anyway. Follow-up patches will replace open_count by it).
Also note that generic VFS revoke support could allow us to drop this
ref-count again. We could then just synchronously disable any fops->xy()
calls. However, this is not the case, yet, and no such patches are
in sight (and I seriously question the idea of dropping the ref-cnt
again).
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Add guard to check whether RGB output is already enabled in the way it's
done for HDMI output. Fixes possible hang on trying to disable output twice
(first time during driver probe and second on fb registering).
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These patches fix some issues caused by the DRM panel support from the
previous pull request and add two more panels (for the Toshiba AC100 as
well as the Seaboard and Ventana).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=NfNj
-----END PGP SIGNATURE-----
Merge tag 'drm/for-3.14-rc1-20140123' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.14-rc1 (update)
These patches fix some issues caused by the DRM panel support from the
previous pull request and add two more panels (for the Toshiba AC100 as
well as the Seaboard and Ventana).
* tag 'drm/for-3.14-rc1-20140123' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Obtain head number from DT
drm/panel: update EDID BLOB in panel_simple_get_modes()
gpu: host1x: Remove unnecessary include
drm/tegra: Use proper data type
drm/tegra: Clarify how panel modes override others
drm/tegra: Fix possible CRTC mask for RGB outputs
drm/i915: Use drm_encoder_crtc_ok()
drm: Move drm_encoder_crtc_ok() to core
drm: provide a helper for the encoder possible_crtcs mask
drm/tegra: Don't check resource with devm_ioremap_resource()
drm/panel: Add support for Chunghwa CLAA101WA01A panel
drm/panel: Add support for Samsung LTN101NT05 panel
The head number of a given display controller is fixed in hardware and
required to program outputs appropriately. Relying on the driver probe
order to determine this number will not work, since that could yield a
situation where the second head was probed first and would be assigned
head number 0 instead of 1.
By explicitly specifying the head number in the device tree, it is no
longer necessary to rely on these assumptions. As a fallback, if the
property isn't available, derive the head number from the display
controller node's position in the device tree. That's somewhat more
reliable than the previous default but not a proper solution.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When a panel advertises one or more modes, they are used exclusively.
Other methods for obtaining the mode, such as DDC as used for HDMI or
binary EDID blobs embedded in the DT, are ignored. The panel drivers
should be providing this functionality if they want to expose it as
well.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The mask of possible CRTCs that an output (DRM encoder) can be attached
to is relative to the position within the DRM device's list of CRTCs.
Deferred probing can cause this to not match the pipe number associated
with a CRTC. Use the newly introduced drm_crtc_mask() to compute the
mask by looking up the proper index of the given CRTC in the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
devm_ioremap_resource() does sanity checks on the given resource. No
need to duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This series of changes brings DRM panel support as well as initial code
to register DSI hosts and peripherals and bind them to DSI drivers. The
panel and DSI code are both used by the simple panel driver.
The Tegra-specific changes build on top of this work to add support for
various panels found on Tegra boards. New drivers enable the DSI host
found on Tegra114 and a special hardware block that calibrates the pads
used for DSI and CSI. The host1x and the display controller drivers gain
basic Tegra124 support. To round of the new features, the DRM driver now
sports a very simple PRIME implementation.
In addition there are various improvements such as the host1x API being
exported so that client drivers (like the Tegra DRM driver) can be built
as modules. HDMI now does better power management and legacy FBDEV can
now be disabled via Kconfig (though it's still enabled by default). A
few sparse warnings have been squashed and various parts of the code
have become more robust.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=lQsh
-----END PGP SIGNATURE-----
Merge tag 'drm/for-3.14-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.14-rc1
This series of changes brings DRM panel support as well as initial code
to register DSI hosts and peripherals and bind them to DSI drivers. The
panel and DSI code are both used by the simple panel driver.
The Tegra-specific changes build on top of this work to add support for
various panels found on Tegra boards. New drivers enable the DSI host
found on Tegra114 and a special hardware block that calibrates the pads
used for DSI and CSI. The host1x and the display controller drivers gain
basic Tegra124 support. To round of the new features, the DRM driver now
sports a very simple PRIME implementation.
In addition there are various improvements such as the host1x API being
exported so that client drivers (like the Tegra DRM driver) can be built
as modules. HDMI now does better power management and legacy FBDEV can
now be disabled via Kconfig (though it's still enabled by default). A
few sparse warnings have been squashed and various parts of the code
have become more robust.
* tag 'drm/for-3.14-rc1' of git://anongit.freedesktop.org/tegra/linux: (121 commits)
drm/tegra: fix compile w/ CONFIG_DYNAMIC_DEBUG
drm/tegra: Add PRIME support
drm/tegra: Relocate some output-specific code
drm/tegra: Add Tegra124 DC support
drm/tegra: Fix small leak on error in tegra_fb_alloc()
drm/tegra: Make legacy fbdev support optional
drm/tegra: Sort reverse-dependencies alphabetically
drm/tegra: Fix return value check
drm/tegra: Add DSI support
drm/tegra: Disable outputs for power-saving
drm/tegra: Track HDMI enable state
drm/tegra: Fix HDMI audio frequency typo
drm/tegra: Do not export tegra_bo_ops
drm/tegra: Remove spurious blank line
drm/tegra: Increase compile test coverage
drm/tegra: Allow the driver to be built as a module
gpu: host1x: Add Tegra124 support
gpu: host1x: clk_round_rate() can return a zero upon error
gpu: host1x: Fix build warnings
gpu: host1x: Increase compile test coverage
...
With CONFIG_DYNAMIC_DEBUG=y, the following compile error occurs:
drivers/gpu/drm/tegra/mipi-phy.c: In function ‘mipi_dphy_timing_validate’:
drivers/gpu/drm/tegra/mipi-phy.c:69:11: error: ‘EINVAL’ undeclared (first use in this function)
drivers/gpu/drm/tegra/mipi-phy.c:69:11: note: each undeclared identifier is reported only once for each function it appears in
Fix this by directly including the header that defines EINVAL.
Fixes: dec727399a ("drm/tegra: Add DSI support")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement very basic PRIME support. This currently only works with
buffers that are contiguous in memory and will refuse to import any
physically non-contiguous buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of the code in the CRTC's mode setting code is specific to the RGB
output or needs to be called slightly differently depending on the type
of output. Push that code down into the output drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 and later support interlacing, but the driver doesn't support
it yet. Make sure interlacing stays disabled on hardware that supports
it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If we don't have enough memory for ->planes then we leak "fb".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A lot of the modern userspace is capable of working without the legacy
fbdev support. kmscon can be used as a replacement for the framebuffer
console, and KMS X drivers create their own framebuffers.
Most people don't have a system where all of this works yet, though, so
leave support enabled by default.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In case of error, the devm_ioremap_resource() function returns ERR_PTR()
and never NULL. The NULL test in the return value check should therefore
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.
Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When an output is disabled, its DPMS mode is usually set to off. Instead
of only disabling the panel (if one is attached), turn the output off
entirely to save more power.
HDMI doesn't have any panels attached, so it previously didn't save any
power at all. With this commit, however, the complete HDMI interface
will be turned off, therefore allowing an attached monitor to go into a
standby mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core doesn't track enable and disable state of encoders and/or
connectors, so calls to the output's .enable() and .disable() are not
guaranteed to be balanced. Track the enable state internally so that
calls to regulator and clock frameworks remain balanced.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These buffer object operations are never used outside of the GEM
implementation so there is no use in exporting them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Treat both negative and zero return values from clk_round_rate() as
errors. This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather than a
signed type, since some clock sources can generate rates higher than
(2^31)-1 Hz.
Eventually, when calling clk_round_rate(), only a return value of zero
will be considered a error. All other values will be considered valid
rates. The comparison against values less than 0 is kept to preserve
the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: Arto Merilainen <amerilainen@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Terje Bergström <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There's really no need for the drm core to keep a list of all
devices of a given driver - the linux device model keeps perfect
track of this already for us.
The exception is old legacy ums drivers using pci shadow attaching.
So rename the lists to make the use case clearer and rip out everything
else.
v2: Rebase on top of David Herrmann's drm device register changes.
Also drop the bogus dev_set_drvdata for platform drivers that somehow
crept into the original version - drivers really should be in full
control of that field.
v3: Initialize driver->legacy_dev_list outside of the loop, spotted by
David Herrmann.
v4: Rebase on top of the newly created host1x drm_bus for tegra.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the DRM panel framework to attach a panel to an output. If the panel
attached to a connector supports supports the backlight brightness
accessors, a property will be available to allow the brightness to be
modified from userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' into drm/for-next
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
copy_from_user() returns the number of bytes remaining if it fails, but
we want to return -EFAULT here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The fbdev screen memory pointer is annotated __iomem, so cast the kernel
virtual address to that address space to make the warning go away.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the association to a DC was done via the encoder's .crtc
field. That has the disadvantage that when an encoder is detached from
its CRTC, that field is set to NULL, leading to situations where it is
impossible to access the DC registers required by the RGB output.
However, the coupling between DC and RGB output is really fixed on
Tegra. While they can be detached logically in DRM, the RGB output can
rely on the DC's existence.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When upcasting a NULL CRTC object, propagate the NULL pointer instead of
some invalid pointer. This allows subsequent code to check that the cast
object is valid.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The biggest part of the changes is the decoupling of the host1x and DRM
drivers followed by the move of Tegra DRM back to drivers/gpu/drm/tegra
from whence it came. There is a lot of cleanup as well, and the drivers
can now be properly unloaded and reloaded.
HDMI support for the Tegra114 SoC was contributed by Mikko Perttunen.
gr2d support was extended to Tegra114 and the gr3d driver that has been
in the works for quite some time finally made it in. All pieces to run
an OpenGL driver on top of an upstream kernel are now available.
Support for syncpoint bases was added by Arto Merilainen. This is useful
for synchronizing between command streams from different engines such as
gr2d and gr3d.
Erik Faye-Lund and Wei Yongjun contributed various small fixes. Thanks!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=qc03
-----END PGP SIGNATURE-----
Merge tag 'drm/for-3.13-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.13-rc1
The biggest part of the changes is the decoupling of the host1x and DRM
drivers followed by the move of Tegra DRM back to drivers/gpu/drm/tegra
from whence it came. There is a lot of cleanup as well, and the drivers
can now be properly unloaded and reloaded.
HDMI support for the Tegra114 SoC was contributed by Mikko Perttunen.
gr2d support was extended to Tegra114 and the gr3d driver that has been
in the works for quite some time finally made it in. All pieces to run
an OpenGL driver on top of an upstream kernel are now available.
Support for syncpoint bases was added by Arto Merilainen. This is useful
for synchronizing between command streams from different engines such as
gr2d and gr3d.
Erik Faye-Lund and Wei Yongjun contributed various small fixes. Thanks!
* tag 'drm/for-3.13-rc1' of git://anongit.freedesktop.org/tegra/linux: (45 commits)
drm/tegra: Reserve syncpoint base for gr3d
drm/tegra: Reserve base for gr2d
drm/tegra: Deliver syncpoint base to user space
gpu: host1x: Add syncpoint base support
gpu: host1x: Add 'flags' field to syncpt request
drm/tegra: Disable clock on probe failure
gpu: host1x: Disable clock on probe failure
drm/tegra: Support bottom-up buffer objects
drm/tegra: Add support for tiled buffer objects
drm/tegra: Add 3D support
drm/tegra: Introduce tegra_drm_submit()
drm/tegra: Use symbolic names for gr2d registers
drm/tegra: Start connectors with correct DPMS mode
drm/tegra: hdmi: Enable VDD earlier for hotplug/DDC
drm/tegra: hdmi: Fix build warnings
drm/tegra: hdmi: Detect DVI-only displays
drm/tegra: Add Tegra114 HDMI support
drm/tegra: hdmi: Parameterize based on compatible property
drm/tegra: hdmi: Rename tegra{2,3} to tegra{20,30}
gpu: host1x: Add support for Tegra114
...
This patch modifies the gr2d to reserve a base for syncpoint.
Signed-off-by: Arto Merilainen <amerilainen@nvidia.com>
Reviewed-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds a separate ioctl for delivering syncpoint base number
to user space. If the syncpoint does not have an associated base, the
function returns -ENXIO.
Signed-off-by: Arto Merilainen <amerilainen@nvidia.com>
Reviewed-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Functions host1x_syncpt_request() and _host1x_syncpt_alloc() have
been taking a separate boolean flag ('client_managed') for indicating
if the syncpoint value should be tracked by the host1x driver.
This patch converts the field into generic 'flags' field so that
we can easily add more information while requesting a syncpoint.
Clients are adapted to use the new interface accordingly.
Signed-off-by: Arto Merilainen <amerilainen@nvidia.com>
Reviewed-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a missing clk_disable_unprepare() before returning from the driver's
.probe() function on error.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The gr3d engine renders images bottom-up. Allow buffers that are used
for 3D content to be marked as such and implement support in the display
controller to present them properly.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The gr2d and gr3d engines work more efficiently on buffers with a tiled
memory layout. Allow created buffers to be marked as tiled so that the
display controller can scan them out properly.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Initialize and power the 3D unit on Tegra20, Tegra30 and Tegra114 and
register a channel with the Tegra DRM driver so that the unit can be
used from userspace.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Command stream submissions are the same across all devices that expose
a channel to userspace, so move the code into a generic function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of using magic numbers for the registers which contain memory
addresses in the firewall table, using symbolic names.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A connector's DPMS mode isn't initialized by default, therefore using a
default of 0 (DRM_MODE_DPMS_ON). This can cause problems in that the DRM
core won't explicitly turn on a connector because it thinks that it is
already on.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The VDD regulator used to be enabled only at tegra_output_hdmi_enable,
which is called after a sink is detected. However, the HDMI hotplug pin
works by returning the voltage supplied by the VDD pin, so this meant
that the hotplug pin was never asserted and the sink was not detected
unless the VDD regulator was set to be always on.
This patch moves the enable to the tegra_hdmi_init() function to make
sure the regulator will get enabled and therefore ensure proper hotplug
detection.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These seem to show up when building for architectures other than ARM,
which I guess will never happen. The reason why the kbuild test bot ran
into these was a missing dependency which has hence been fixed. Still it
doesn't hurt to fix them anyway.
Reported-by: kbuild test bot <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use EDID data to determine whether the display supports HDMI or DVI
only. The HDMI output used to assume to be connected to HDMI displays,
but that broke support for DVI displays that don't understand the
interspersed audio/other data.
To be on the safe side, default to DVI if no EDID data is available.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
[treding@nvidia.com: move detection to separate function]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra114 TMDS configuration requires a new peak_current field and the
driver current override bit has changed position.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a structure to parameterize the code to handle differences between
the HDMI hardware on various SoC generations. This removes the need to
clutter the code with checks for individual compatible values.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Everything related to Tegra uses Tegra20 and Tegra30 instead of Tegra2
and Tegra3, respectively. Rename the TMDS arrays in the HDMI driver for
consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since the .init() and .exit() functions are executed whenever the DRM
driver is loaded or unloaded, care must be taken not to use them for
resource allocation. Otherwise deferred probing cannot be used, since
the .init() and .exit() are not run at probe time. Similarly the code
that frees resources must be run at .remove() time. If it is run from
the .exit() function, it can release resources multiple times.
To handle this more consistently, rename the tegra_output_parse_dt()
function to tegra_output_probe() and introduce tegra_output_remove()
which can be used to free output-related resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DRM driver is unloaded, all the associated resources must be
cleaned up and zeroed out. This is necessary because of the architecture
of the Tegra DRM driver, where not all subdrivers are unloaded along
with the DRM driver. Therefore device-managed managed won't be freed and
memory cannot be assumed to have been cleared (because it hasn't been
reallocated using kzalloc()) by the time the DRM driver is reloaded. It
is therefore necessary to zero out the structures to prevent strange
errors (such as slab corruptions) from occurring.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit ac24c2204a ("drm/tegra: Use generic
HDMI infoframe helpers") added "select DRM_HDMI" to the DRM_TEGRA
Kconfig entry. But there is no Kconfig symbol named DRM_HDMI. The select
statement for that symbol is a nop. Drop it.
What was needed to use HDMI functionality was to select HDMI (which this
entry already did through depending on DRM) and to include linux/hdmi.h
(which this commit also did).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
Thierry writes:
"Remove a duplicate implementation of the CEA VIC lookup and move the CEA
and other mode tables to drm_edid.c to make it more difficult to create
duplicates of the tables.
Add some helpers to pack CEA-861/HDMI AVI, audio and SPD infoframes into
binary buffers that can easily be written into hardware registers. A new
helper function makes it easy construct an AVI infoframe from a DRM
display mode.
Convert the Tegra and Radeon drivers to use the new HDMI helpers."
* 'drm/hdmi-for-3.9' of git://anongit.freedesktop.org/tegra/linux:
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
This list is most useful to inspect whether framebuffer reference
counting works as expected. The code is loosely based on the i915
implementation.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
bpp stores the number of bytes per pixel, but color expansion needs to
be enabled for less than 24 bits per pixel.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The Tegra TRM says that the ACT_REQ and UPDATE fields cannot be
programmed at the same time so they are updated in two consecutive
writes instead.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
All the necessary support bits like .mode_set_base() and VBLANK are now
available, so page-flipping case easily be implemented on top.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Implement support for the VBLANK IOCTL. Note that Tegra is somewhat
special in this case because it doesn't use the generic IRQ support
provided by the DRM core (DRIVER_HAVE_IRQ) but rather registers one
interrupt handler for each display controller.
While at it, clean up the way that interrupts are enabled to ensure
that the VBLANK interrupt only gets enabled when required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The sequence for replacing the scanout buffer is much shorter than a
full mode change operation so implementing this callback considerably
speeds up cases where only a new framebuffer is to be scanned out.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add support for the B and C planes which support RGB and YUV pixel
formats and can be used as overlays or hardware cursor. Currently 32-bit
XRGB as well as UYVY, YUV420 and YUV422 pixel formats are advertised.
Other formats should be easy to add but these are the most common ones
and should cover the majority of use-cases.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tegra uses the CMA FB helpers so framebuffers passed to the driver need
to use the corresponding functions to access the underlying GEM objects.
This used to work because struct tegra_framebuffer was sufficiently
similar to struct drm_fb_cma but that isn't guaranteed to stay that way.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Use the generic HDMI infoframe helpers to get rid of the NVIDIA Tegra
reimplementation.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
drm_fbdev_cma_init does the inital fbcon setup by calling down into
drm_fb_helper_initial_config, so no need at all to restore the just
set up configuration right away ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Migrate Tegra clock support to drivers/clk/tegra, this involves
moving:
1. definition of tegra_cpu_car_ops to clk.c
2. definition of reset functions to clk-peripheral.c
3. change parent of cpu clock.
4. Remove legacy clock initialization.
5. Initialize clocks using DT.
6. Remove all instance of mach/clk.h
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: use to_clk_periph_gate().]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 83c0bcb694.
Lucas pointed out this was a mistake, and I missed the discussion,
so just revert it out to save a rebase.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The intention is to program exactly WIN_A, not WIN_A and possibly
others.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is no gem.c anymore, those functions are implemented by the
drm_cma_helpers now.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The 720p and 1080p entries are completely redundant, as we are matching
the table entries against <=pclk.
Also generalize the comment, as we are using those table entries even
when driving other modes than the standard TV ones.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Window properties are programmed through a shared aperture and have to
happen atomically. Also we do the read-update-write dance on some of the
shared regs.
To make sure that different functions don't stumble over each other
protect the register access with a mutex.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
No real problem for now, as nothing is using this, but leaving it
unitialized is asking for trouble later on.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes wrong picture offset observed when using HDMI output with a
Technisat HD TV.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Mark Zhang <markz@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add support for host1x, the display controllers and HDMI on the Tegra30
SoC.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of using the stride derived from the display mode, use the pitch
associated with the currently active framebuffer. This fixes a bug where
the LCD display content would be skewed when enabling HDMI with a video
mode different from that of the LCD.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit adds support for the HDMI output on the Tegra20 SoC. Only
one such output is available, but it can be driven by either of the two
display controllers.
A lot of work on this patch has been contributed by NVIDIA's Mark Zhang
<markz@nvidia.com> and many other people at NVIDIA were very helpful in
getting the HDMI support and surrounding infrastructure to work.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Zhang <markz@nvidia.com>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit adds a KMS driver for the Tegra20 SoC. This includes basic
support for host1x and the two display controllers found on the Tegra20
SoC. Each display controller can drive a separate RGB/LVDS output.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Zhang <markz@nvidia.com>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
