Commit Graph

161 Commits

Author SHA1 Message Date
Eric Lapuyade
2bed278517 NFC: NCI: Modify NCI SPI to implement CS/INT handshake per the spec
The NFC Forum NCI specification defines both a hardware and software
protocol when using a SPI physical transport to connect an NFC NCI
Chipset. The hardware requirement is that, after having raised the chip
select line, the SPI driver must wait for an INT line from the NFC
chipset to raise before it sends the data. The chip select must be
raised first though, because this is the signal that the NFC chipset
will detect to wake up and then raise its INT line. If the INT line
doesn't raise in a timely fashion, the SPI driver should abort
operation.

When data is transferred from Device host (DH) to NFC Controller (NFCC),
the signaling sequence is the following:

Data Transfer from DH to NFCC
• 1-Master asserts SPI_CSN
• 2-Slave asserts SPI_INT
• 3-Master sends NCI-over-SPI protocol header and payload data
• 4-Slave deasserts SPI_INT
• 5-Master deasserts SPI_CSN

When data must be transferred from NFCC to DH, things are a little bit
different.

Data Transfer from NFCC to DH
• 1-Slave asserts SPI_INT -> NFC chipset irq handler called -> process
reading from SPI
• 2-Master asserts SPI_CSN
• 3-Master send 2-octet NCI-over-SPI protocol header
• 4-Slave sends 2-octet NCI-over-SPI protocol payload length
• 5-Slave sends NCI-over-SPI protocol payload
• 6-Master deasserts SPI_CSN

In this case, SPI driver should function normally as it does today. Note
that the INT line can and will be lowered anytime between beginning of
step 3 and end of step 5. A low INT is therefore valid after chip select
has been raised.

This would be easily implemented in a single driver. Unfortunately, we
don't write the SPI driver and I had to imagine some workaround trick to
get the SPI and NFC drivers to work in a synchronized fashion. The trick
is the following:

- send an empty spi message: this will raise the chip select line, and
send nothing. We expect the /CS line will stay arisen because we asked
for it in the spi_transfer cs_change field
- wait for a completion, that will be completed by the NFC driver IRQ
handler when it knows we are in the process of sending data (NFC spec
says that we use SPI in a half duplex mode, so we are either sending or
receiving).
- when completed, proceed with the normal data send.

This has been tested and verified to work very consistently on a Nexus
10 (spi-s3c64xx driver). It may not work the same with other spi
drivers.

The previously defined nci_spi_ops{} whose intended purpose were to
address this problem are not used anymore and therefore totally removed.

The nci_spi_send() takes a new optional write_handshake_completion
completion pointer. If non NULL, the nci spi layer will run the above
trick when sending data to the NFC Chip. If NULL, the data is sent
normally all at once and it is then the NFC driver responsibility to
know what it's doing.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 14:59:56 +02:00
Eric Lapuyade
22d4aae589 NFC: NCI: nci_spi_recv_frame() now returns (not forward) the read frame
Previously, nci_spi_recv_frame() would directly transmit incoming frames
to the NCI Core. However, it turns out that some NFC NCI Chips will add
additional proprietary headers that must be handled/removed before NCI
Core gets a chance to handle the frame. With this modification, the chip
phy or driver are now responsible to transmit incoming frames to NCI
Core after proper treatment, and NCI SPI becomes a driver helper instead
of sitting between the NFC driver and NCI Core.

As a general rule in NFC, *_recv_frame() APIs are used to deliver an
incoming frame to an upper layer. To better suit the actual purpose of
nci_spi_recv_frame(), and go along with its nci_spi_send()
counterpart, the function is renamed to nci_spi_read()

The skb is returned as the function result

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 14:25:41 +02:00
Eric Lapuyade
a4ada6cadb NFC: NCI: zero struct spi_transfer variables before usage
Using ARM compiler, and without zero-ing spi_transfer, spi-s3c64xx
driver would issue abnormal errors due to bpw field value being set to
unexpected value. This structure MUST be set to all zeros except for
those field specifically used.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 14:21:09 +02:00
Eric Lapuyade
645d5087bd NFC: NCI: Store the spi device pointer from the spi instance
Storing the spi device was forgotten in the original implementation,
which would pretty obviously cause some kind of serious crash when
actually trying to send something through that device.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 02:02:30 +02:00
Eric Lapuyade
fa544fff62 NFC: NCI: Simplify NCI SPI to become a simple framing/checking layer
NCI SPI layer should not manage the nci dev, this is the job of the nci
chipset driver. This layer should be limited to frame/deframe nci
packets, and optionnaly check integrity (crc) and manage the ack/nak
protocol.

The NCI SPI must not be mixed up with an NCI dev. spi_[dev|device] are
therefore renamed to a simple spi for more clarity.
The header and crc sizes are moved to nci.h so that drivers can use
them to reserve space in outgoing skbs.
nci_spi_send() is exported to be accessible by drivers.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 01:35:41 +02:00
Eric Lapuyade
d593751129 NFC: NCI: Rename spi ndev -> nsdev and nci_dev -> ndev for consistency
An hci dev is an hdev. An nci dev is an ndev. Calling an nci spi dev an
ndev is misleading since it's not the same thing. The nci dev contained
in the nci spi dev is also named inconsistently.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 01:35:40 +02:00
Eric Lapuyade
079797c3b7 NFC: NCI: Fix wrong allocation size in nci_spi_allocate_device()
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 01:35:40 +02:00
Frederic Danis
7427b370e0 NFC: Fix NCI over SPI build
kbuild test robot found following error:

     net/built-in.o: In function `nci_spi_send':
  >> spi.c:(.text+0x19a76f): undefined reference to `crc_ccitt'

Add CRC_CCITT module to Kconfig to fix it

Reported-by: kbuild test robot.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-07-19 16:55:26 +02:00
Samuel Ortiz
0a946301c2 NFC: Extend and fix the internal secure element API
Secure elements need to be discovered after enabling the NFC controller.
This is typically done by the NCI core and the HCI drivers (HCI does not
specify how to discover SEs, it is left to the specific drivers).
Also, the SE enable/disable API explicitely takes a SE index as its
argument.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 13:44:53 +02:00
Samuel Ortiz
0b456c418a NFC: Remove the static supported_se field
Supported secure elements are typically found during a discovery process
initiated when the NFC controller is up and running. For a given NFC
chipset there can be many configurations (embedded SE or not, with or
without a SIM card wired to the NFC controller SWP interface, etc...) and
thus driver code will never know before hand which SEs are available.
So we remove this field, it will be replaced by a real SE discovery
mechanism.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 13:44:19 +02:00
Frederic Danis
391d8a2da7 NFC: Add NCI over SPI receive
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.

Transaction starts by emitting "Direct read" and acknowledged mode
bytes. Then packet length is read allowing to allocate correct NCI
socket buffer. After that payload is retrieved.

A delay after the transaction can be added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.

If acknowledged mode is set:
- CRC of header and payload is checked
- if frame reception fails (CRC error): NACK is sent
- if received frame has ACK or NACK flag: unblock nci_spi_send()

Payload is passed to NCI module.

At the end, driver interruption is re asserted.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 13:44:16 +02:00
Frederic Danis
ee9596d467 NFC: Add NCI over SPI send
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.

The NCI over SPI header is added in front of NCI packet.
If acknowledged mode is set, CRC-16-CCITT is added to the packet.
Then the packet is forwarded to SPI module to be sent.

A delay after the transaction is added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.

After data has been sent, driver interruption is re-asserted.

If acknowledged mode is set, nci_spi_send will block until
acknowledgment is received.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 13:44:15 +02:00
Frederic Danis
8a00a61b0e NFC: Add basic NCI over SPI
The NFC Forum defines a transport interface based on
Serial Peripheral Interface (SPI) for the NFC Controller
Interface (NCI).

This module implements the SPI transport of NCI, calling SPI module
directly to read/write data to NFC controller (NFCC).

NFCC driver should provide functions performing device open and close.
It should also provide functions asserting/de-asserting interruption
to prevent TX/RX race conditions.
NFCC driver can also fix a delay between transactions if needed by
the hardware.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 13:44:03 +02:00
Frederic Danis
1095e69f47 NFC: NCI: Fix skb->dev usage
skb->dev is used for carrying a net_device pointer and not
an nci_dev pointer.

Remove usage of skb-dev to carry nci_dev and replace it by parameter
in nci_recv_frame(), nci_send_frame() and driver send() functions.

NfcWilink driver is also updated to use those functions.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-06-14 00:25:53 +02:00
Samuel Ortiz
390a1bd853 NFC: Initial Secure Element API
Each NFC adapter can have several links to different secure elements and
that property needs to be exported by the drivers.
A secure element link can be enabled and disabled, and card emulation will
be handled by the currently active one. Otherwise card emulation will be
host implemented.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-10 00:51:54 +01:00
Kees Cook
f152218840 NFC: Remove CONFIG_EXPERIMENTAL from the NCI Makefile
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.

Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-10-26 18:26:53 +02:00
Szymon Janc
0f45077222 NFC: Fix some code style and whitespace issues
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-10-26 18:26:52 +02:00
Szymon Janc
874934f4d4 NFC: Fix style issues with logical operations
Logical continuations should be on the previous line.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-10-26 18:26:49 +02:00
Szymon Janc
f9fc36f46f NFC: Remove not needed local variable in nci_set_local_general_bytes
No need for local rc variable as result of nci_request can be returned
directly.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-10-26 18:26:48 +02:00
Szymon Janc
460d8f970e NFC: Use NFC_MAX_GT_LEN to check len in nci_set_local_general_bytes
local_gb is of size NFC_MAX_GT_LEN and len is used as index for it.
Check len against this instead of NCI_MAX_PARAM_LEN before accessing
local_gb.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-10-26 18:26:48 +02:00
Ilan Elias
767f19ae69 NFC: Implement NCI dep_link_up and dep_link_down
During NFC-DEP target activation, store the remote
general bytes to be used later in dep_link_up.
When dep_link_up is called, activate the NFC-DEP target,
and forward the remote general bytes.
When dep_link_down is called, deactivate the target.

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-25 00:17:23 +02:00
Ilan Elias
ac20683840 NFC: Parse NCI NFC-DEP activation params
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-25 00:17:23 +02:00
Ilan Elias
7e0352306f NFC: Set local general bytes in nci_start_poll
If initiator protocol is NFC-DEP, set the local general bytes
in nci_start_poll.

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-25 00:17:23 +02:00
John W. Linville
d369f7b2b2 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2012-07-17 15:31:33 -04:00
Dave Jones
8a70e7f8f3 NFC: NCI module license 'unspecified' taints kernel
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-12 14:48:41 -04:00
Samuel Ortiz
01d719a228 NFC: Add ISO 14443 type B protocol
Some devices (e.g. Sony's PaSoRi) can not do type B polling, so we have
to make a distinction between ISO14443 type A and B poll modes.

Cc: Eric Lapuyade <eric.lapuyade@intel.com>
Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-09 16:42:24 -04:00
John W. Linville
635d999fd3 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	net/mac80211/mlme.c
2012-07-09 16:34:34 -04:00
Dan Rosenberg
67de956ff5 NFC: Prevent multiple buffer overflows in NCI
Fix multiple remotely-exploitable stack-based buffer overflows due to
the NCI code pulling length fields directly from incoming frames and
copying too much data into statically-sized arrays.

Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: stable@kernel.org
Cc: security@kernel.org
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-06-25 16:38:40 +02:00
Samuel Ortiz
be9ae4ce4e NFC: Introduce target mode tx ops
And rename the initiator mode data exchange ops for consistency sake.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-06-04 21:34:30 +02:00
Samuel Ortiz
fe7c580073 NFC: Add target mode protocols to the polling loop startup routine
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-06-04 21:34:29 +02:00
H Hartley Sweeten
799030b75a NFC: Quiet nci/ntf.c sparse noise about plain integer as NULL pointer
Pointers should be cleared with NULL, not 0.

Quiets a couple sparse warnings of the type:

warning: Using plain integer as NULL pointer

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-15 17:30:30 -04:00
H Hartley Sweeten
502b424082 NFC: Include nci_core.h to nci/lib.c
Include the header to pickup the exported symbol prototype.

Quites the sparse warning:

warning: symbol 'nci_to_errno' was not declared. Should it be static?

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-15 17:30:29 -04:00
H Hartley Sweeten
040487f364 NFC: Quiet nci/data.c sparse noise about plain integer as NULL pointer
Pointers should be cleared with NULL, not 0.

Quiets a couple sparse warnings of the type:

warning: Using plain integer as NULL pointer

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-15 17:30:29 -04:00
Eric Lapuyade
9009943326 NFC: Cache the core NFC active target pointer instead of its index
The NFC Core now caches the active nfc target pointer, thereby avoiding
the need to lookup the target table for each invocation of a driver ops.
Consequently, pn533, HCI and NCI now directly receive an nfc_target
pointer instead of a target index.

Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-15 17:27:59 -04:00
Samuel Ortiz
c4fbb6515a NFC: The core part should generate the target index
The target index can be used by userspace to uniquely identify a target
and thus should be kept unique, per NFC adapter. Moreover, some protocols
do not provide a logical index when discovering new targets, so we have to
generate one for them.
For NCI or pn533 to fetch their logical index, we added a logical_idx field
to the target structure.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-12 15:10:37 -04:00
Samuel Ortiz
eb9bc6e9a0 NFC: NCI code identation fixes
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:25 -05:00
Dan Carpenter
6269cc83e7 nfc: NULL vs zero in nci_activate_target()
This is a pointer so it should be NULL instead of zero.  Sparse
complains about this stuff:
net/nfc/nci/core.c:447:37: warning: Using plain integer as NULL pointer

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-27 14:57:04 -05:00
Ilan Elias
019c4fbaa7 NFC: Add NCI multiple targets support
Add the ability to select between multiple targets in NCI.
If only one target is found, it will be auto-activated.
If more than one target is found, then DISCOVER_NTF will be
generated for each target, and the host should select one by
calling DISCOVER_SELECT_CMD. Then, the target will be activated.
If the activation fails, GENERIC_ERROR_NTF is generated.

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-24 14:32:29 -05:00
Ilan Elias
8939e47fc9 NFC: Clearly separate NCI states from flags
Make a clear separation between NCI states and flags.
This is required in order to support more NCI states (e.g.
for multiple targets support).

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-24 14:32:28 -05:00
Ilan Elias
c4bf98b220 NFC: Add NCI data exchange timer
Add NCI data exchange timer to catch timeouts,
and call the data exchange callback with an error.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-24 14:21:55 -05:00
Ilan Elias
d5a2ca60e4 NFC: Export new attributes sensb_res and sensf_res
Export new attributes sensb_res for tech B and sensf_res
for tech F in the target info (returned as a response to
NFC_CMD_GET_TARGET).
The max size of the attributes nfcid1, sensb_res and sensf_res
is exported to user space though include/linux/nfc.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-24 14:21:15 -05:00
Ilan Elias
bd7e01bc7e NFC: Complete NCI deactivate in deactivate_ntf
If a target was active, complete the NCI deactivate request
only in deactivate_ntf. Otherwise, complete it at deactivate_rsp.
Deactivate_ntf represents the actual disconnection event (sent from
the NCI controller).

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-24 14:08:38 -05:00
Ilan Elias
288e0713f4 NFC: Export a new attribute nfcid1 in target info
The nfcid1 is the NFC-A identifier.
It is exported as an attribute of the target info
(returned as a response to NFC_CMD_GET_TARGET).

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:43 -05:00
Ilan Elias
004161cb52 NFC: Handle error during NCI data exchange
Add support for NCI Interface Error Notification.
When this notification is received and we're during a
data exchange transaction, indicate an error to the NFC
core layer via the data exchange callback.

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:39 -05:00
Ilan Elias
637d85a7cd NFC: Update names and structs to NCI spec 1.0 d22
Addition, deletion, and modification of NCI constants.
Changes in NCI commands, responses, and notifications structures.

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:39 -05:00
Samuel Ortiz
52858b51b2 NFC: Add function name to the NFC pr_fmt() routine
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-12-14 14:50:12 -05:00
John W. Linville
5d22df200b Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	drivers/net/wireless/iwlwifi/iwl-agn.c
2011-12-14 14:35:41 -05:00
Dan Carpenter
f8c141c3e9 nfc: signedness bug in __nci_request()
wait_for_completion_interruptible_timeout() returns -ERESTARTSYS if
interrupted so completion_rc needs to be signed.  The current code
probably returns -ETIMEDOUT if we hit this situation, but after this
patch is applied it will return -ERESTARTSYS.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-12-12 14:23:27 -05:00
Joe Perches
24bf330485 nfc: Remove function tracer like entry messages
Logging messages that mimic function tracer enter/exit
aren't necessary.  Just remove them.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30 15:08:38 -05:00
Joe Perches
20c239c139 nfc: Convert nfc_dbg to pr_debug
Using the standard debugging mechanisms is better than
subsystem specific ones when the subsystem doesn't use
a specific struct.

Coalesce long formats.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30 15:08:36 -05:00
Joe Perches
ed1e0ad881 nfc: Use standard logging styles
Using the normal logging styles is preferred over
subsystem specific styles when the subsystem does
not take a specific struct.

Convert nfc_<level> specific messages to pr_<level>
Add newlines to uses.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-30 15:08:36 -05:00
John W. Linville
515db09338 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux
Conflicts:
	drivers/net/wireless/iwlegacy/iwl-debugfs.c
	drivers/net/wireless/iwlegacy/iwl-rx.c
	drivers/net/wireless/iwlegacy/iwl-scan.c
	drivers/net/wireless/iwlegacy/iwl-tx.c
	include/net/bluetooth/bluetooth.h
2011-11-22 14:05:46 -05:00
Ilan Elias
db98c829b7 NFC: Check if NCI data flow control is used
Check if NCI data flow control is used in nci_tx_work.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-11 12:32:50 -05:00
Ilan Elias
ee4c64fb98 NFC: Removal of unused operations for NCI spec 1.0 d18
Remove unused NCI operations, e.g. create static rf connection.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-11 12:32:50 -05:00
Ilan Elias
e8c0dacd98 NFC: Update names and structs to NCI spec 1.0 d18
Addition, deletion and modification of NCI constants.
Changes in NCI commands, responses and notifications structures.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-11 12:32:50 -05:00
Paul Gortmaker
bc3b2d7fb9 net: Add export.h for EXPORT_SYMBOL/THIS_MODULE to non-modules
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:30:30 -04:00
Dan Carpenter
8ebafde00e NFC: use after free on error
We returned a freed variable on some error paths when the intent was
to return a NULL.  Part of the reason this was missed was that the
code was confusing because it had too many gotos so I removed them
and simplified the flow a bit.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27 14:34:10 -04:00
Ilan Elias
38f04c6b1b NFC: protect nci_data_exchange transactions
Protect 'cb' and 'cb_context' arguments in nci_data_exchange.
In fact, this implements a queue with max length of 1 data
exchange transactions in parallel.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27 14:34:05 -04:00
Ilan Elias
de054799b7 NFC: implicitly deactivate in nci_start_poll
When start_poll is called, and a target was implicitly activated,
we need to implicitly deactivate it.
On the other hand, when the target was activated by the user,
we should not deactivate it.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27 14:34:04 -04:00
Ilan Elias
2eb1dc101e NFC: improve readability of an 'if' in nci core.c
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27 14:34:04 -04:00
Ilan Elias
6a2968aaf5 NFC: basic NCI protocol implementation
The NFC Controller Interface (NCI) is a standard
communication protocol between an NFC Controller (NFCC)
and a Device Host (DH), defined by the NFC Forum.

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-20 14:43:49 -04:00