I recently noticed that when calling:
# ethtool -s eth0 autoneg on
on a 5722 (though I'm sure it's not specific to that card) that
subsequent checks of the cards status looked like this:
# ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised auto-negotiation: No <---- This seems odd?!?
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
Link detected: yes
I noticed that the following commit:
commit 3600d918d8
Author: Michael Chan <mchan@broadcom.com>
Date: Thu Dec 7 00:21:48 2006 -0800
[TG3]: Allow partial speed advertisement.
Honor the advertisement bitmask from ethtool. We used to always
advertise the full capability when autoneg was set to on.
changed things around so that ethtool speed settings were strictly
followed. Unfortunately ethtool doesn't seem to set ADVERTISED_Autoneg
in the advertising field (and maybe it shouldn't have to). I'd vote
that it should be fixed there, but it should also be added here just in
case someone using ethtool ioctls in their own application gets what
they want.
Adding that flag in tg3_set_settings seemed like the most logical place
since the driver works fine on boot. This is just an issue when
re-enabling autonegotiation, so we should probably nip it there.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a kernel oops triggered by the ksdazzle SIR driver.
We need more space for input frames, and 2048 should be plenty of it.
Signed-off-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for 5784 and 5764 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer products change the way the ASIC revision is obtained. This patch
implements how the driver will extract the revision number.
This patch also adds preliminary CPMU support. CPMU stands for Central
Power Management Unit. The CPMU's role is to put the chip into lower
power states when the operating conditions allow it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer tg3 devices shuffle around the registers in PCI configuration
space. This patch changes the way the driver accesses the PCI
capabilities registers. Hardcoded register locations are replaced with
offsets from pci_find_capability() return values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A merge/cleanup code accidentally dropped 8254x code in and removed
8257x code here. Undo this mistake and use the pci-e relevant register
test similar as to what is in e1000.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A small bug crawled in the -DDEBUG enabled code. Fix this to
properly call the backreference device name.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Debugging statements are added for inbound packets with unknown
header id. Those packets are discarded and no longer processed as
osn-packets.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When the lcs irq routine detects channel failures it drives device recovery.
After this event the device is no longer usable for shutdown requests,
because the lcs_irq routine may get wrong channel status information.
In such a case the lcs_irq routine marks the channel in 'error' state.
The channel state comes back to 'running' after restarting the channels.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
if qeth_set_multicast_list() is performed on 2 CPUs in parallel,
card->ip_list may end corrupted.
Solution: In function __qeth_delete_all_mc()
remove card->ip_list entry before invoking
qeth_deregister_addr_entry(). Thus a 2nd invocation of
qeth_set_multicast_list() cannot try to remove the
same entry twice.
Signed-off-by Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix filling the qdio buffers in EDDP mode.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
HiperSockets infrastructure (layer-3 mode) supports only IPv4 or
IPv6 packets. Sending other packet types disturbs TCP/IP on z/VM,
which issues messages about invalid packets.
Qeth send routine will detect packet type on sending over a
HiperSockets interface (in layer-3 mode) and drop non IP packets.
The error and drop count of the interface is incremented.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With cleanup suggestions and bugs spotted by Stephen Hemminger,
Ingo Oeser, Matheos Worku, and Oliver Hartkopp.
Signed-off-by: David S. Miller <davem@davemloft.net>
pasemi_mac: enable iommu support
Enable IOMMU support for pasemi_mac, but avoid using it on non-partitioned
systems for performance reasons.
The user can override this by selecting the PPC_PASEMI_IOMMU_DMA_FORCE
configuration option.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I've tried to compile 2.6.23-rc8-mm2, but it fails on ipg.c with the
error : ERROR: "__udivdi3" [drivers/net/ipg.ko] undefined!
I've instigated a bit, and I've found this code in ipg.c :
static void ipg_nic_txfree(struct net_device *dev)
{
struct ipg_nic_private *sp = netdev_priv(dev);
void __iomem *ioaddr = sp->ioaddr;
const unsigned int curr = ipg_r32(TFD_LIST_PTR_0) -
(sp->txd_map / sizeof(struct ipg_tx)) - 1;
unsigned int released, pending;
sp->txd_map is an u64
because :
dma_addr_t txd_map;
And in asm-i386/types.h, I see :
#ifdef CONFIG_HIGHMEM64G
typedef u64 dma_addr_t;
#else
typedef u32 dma_addr_t;
#endif
I my config, I use CONFIG_HIGHMEM64G
sizeof(struct ipg_tx) is an u32
So the div failed on i386 because of u64 / u32.
[akpm@linux-foundation.org: cleanups]
Cc: Sorbica Shieh <sorbica@icplus.com.tw>
Cc: Jesse Huang <jesse@icplus.com.tw>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: use buffer index pointer in clean_rx()
Use the new features in B0 for buffer ring index on the receive side. This
means we no longer have to search in the ring for where the buffer
came from.
Also cleanup the RX cleaning side a little, while I was at it.
Note: Pre-B0 hardware is no longer supported, and needs a pile of other
workarounds that are not being submitted for mainline inclusion. So the
fact that this breaks old hardware is not a problem at this time.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: clear out old errors on interface open
Clear out any pending errors when an interface is brought up. Since the bits
are sticky, they might be from interface shutdown time after firmware has
used it, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: update todo list
Remove some stale todo items that have been taken care of. Add a couple
of upcoming ones.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: further performance tweaks
Misc driver tweaks for pasemi_mac:
* Increase ring size (really needed mostly on 10G)
* Take out an unneeded barrier
* Move around a few prefetches and reorder a few calls
* Don't try to clean on full tx buffer, just let things
take their course and stop the queue directly
* Avoid filling on the same line as the interface is
working on to reduce cache line bouncing
* Avoid unneeded clearing of software state (and make the
interface shutdown code handle it)
* Fix up some of the tx ring wrap logic.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: add local skb alignment
Add local SKB alignment to pasemi_mac, since ppc64 in general has it at 0
because of design flaws in some of the IBM server bridge chips. However,
for PWRficient doing the unaligned copies is more expensive than doing
unaligned DMA so make sure the data is aligned instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: workaround for erratum 5971
Implement workarounds for erratum 5971, where L2 hints aren't considered
properly unless the way hint is enabled on the interface. Since L2 isn't
setup to dedicate a way to headers, we need to reset the packet count
by hand so it won't run out of credits.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: implement sg support
Implement SG support for pasemi_mac
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: rework ring management
Rework ring management, switching to an opaque ring format instead of
the struct-based descriptor+pointer setup, since it will be needed for
SG support.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: fix bug in receive buffer dma mapping
skb->len isn't actually set to the size of the allocated skb, so don't
try to use it when figuring out how much to map.
(This hasn't surfaced as a real bug because we effectively disable
translation for the interface, but it still needs fixing for the future)
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: basic error checking
Add some rudimentary error checking to pasemi_mac.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This "algorithm" is used only internally and is not useful.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since I cannot convince the lazy driver authors (hello Michael)
to stop (ab)using the MGMT interface type internally in their
drivers, this patch introduces a new _INVALID type especially
for their use and changes all affected drivers to use it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement much easier and more lightweight locking for
the periodic work.
This also removes the last big busywait loop and replaces it
by a sleeping loop.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the direct call to rfkill on an rfkill event
and replaces it with an input device. This way userspace is also
notified about the event.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds full support for the RFKILL button and
the RFKILL LED trigger.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drive the LEDs through the generic LED triggers.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel now provides a generic hexdump implementation should we need
it again, so we can remove it from zd1211rw. After removing that, only
one single-user function is left in zd_util. Move that to zd_mac and
remove zd_util.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As detailed at https://bugs.gentoo.org/159646 hostap with hostapd confuses
udev by presenting 2 interfaces with the same MAC address. Also, at the time
of detection, the 'type' attribute is 1, identical to other hostap interfaces.
The AP interface is supposed to have type ARPHRD_IEEE80211 (801), but this is
not set until after registration.
Setting it before register_netdev() is called allows us to avoid this
confusion. We can do this by propogating the HOSTAP_INTERFACE type through
to hostap_setup_dev().
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow up to the patches from Denys Vlasenkos
<vda.linux@googlemail.com> to further optimize firmware loading.
1. In bnx2_init_cpus(), we allocate memory for decompression once
and use it repeatedly instead of doing this for every firmware image.
2. We eliminate the BSS and SBSS firmware sections in bnx2_fw*.h since
these are always zeros.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
this are the changes to the smc911x driver, which were necessary
to get it running on the Magic Panel R2 (smsc9115).
It is a SH3-DSP based board. The other patches are available on
the linuxsh-dev mailinglist.
http://marc.info/?l=linuxsh-dev&r=1&b=200708&w=2
It was necessary to set the irq sense to low level.
Therefor the SMC_IRQ_SENSE define was added.
How are the chances for inclusion in 2.6.24?
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Due to stability issues in high load situations the HW queue handling
has to be changed. The HW queues are now stopped and restarted again instead
of destroying and allocating new HW queues.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Previously, bitbanged MDIO was only supported in individual
hardware-specific drivers. This code factors out the higher level
protocol implementation, reducing the hardware-specific portion to
functions setting direction, data, and clock.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The existing OF glue code was crufty and broken. Rather than fix it, it
will be removed, and the ethernet driver now talks to the device tree
directly.
The old, non-CONFIG_PPC_CPM_NEW_BINDING code can go away once CPM
platforms are dropped from arch/ppc (which will hopefully be soon), and
existing arch/powerpc boards that I wasn't able to test on for this
patchset get converted (which should be even sooner).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At least some hardware driven by this driver needs receive buffers
to be aligned on a 16-byte boundary. This usually happens by chance,
but it breaks if slab debugging is enabled.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These macros accomplish nothing other than defeating type checking.
This patch also fixes one instance of the wrong register size being
used that was revealed by enabling type checking.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
