When using VLAN-aware bridges with VXLAN, the VLAN that is mapped to the
VNI of the VXLAN device is that which is configured as "pvid untagged"
on the corresponding bridge port.
When these flags are toggled or when the VLAN is deleted entirely,
remote hosts should not be able to receive packets from the VTEP.
Add a test case for above mentioned scenarios.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VXLAN device is attached to an offloaded bridge, or when a
front-panel port is attached to a bridge that already has a VXLAN
device, mlxsw should offload the existing offloadable FDB entries.
Similarly when VXLAN device is downed, the FDB entries are unoffloaded,
and the marks thus need to be cleared. Similarly when a front-panel port
device is attached to a bridge with a VXLAN device, or when VLAN flags
are tweaked on a VXLAN port attached to a VLAN-aware bridge.
Test that the replaying / clearing logic works by observing transitions
in presence of offload marks under different scenarios.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any existing NVE FDB entries need to be offloaded when NVE is enabled
for a given FID. Recent patches have added fdb_replay op for this, so
just invoke it from mlxsw_sp_nve_fid_enable().
When NVE is disabled on a FID, any existing FDB offloaded marks need to
be cleared on NVE device as well as on its bridge master. An op to
handle this, fdb_clear_offload, has been added to FID ops and NVE ops in
previous patches. Add code to resolve the NVE device, NVE type, and
dispatch to both fdb_clear_offload ops.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are any offloaded FDB entries at bridge master of an NVE device
at the time that it's un-offloaded, their offloaded marks need to be
cleared. How that is done depends on whether the bridge in question is
vlan aware. Therefore add a per-FID-type operation.
Implement the operation for the 802.1q and 802.1d bridges.
Add and publish a function mlxsw_sp_fid_fdb_clear_offload() to dispatch
to the new operation according to FID type.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are any offloaded FDB entries at an NVE device at the time that
it's un-offloaded, their offloaded marks need to be cleared. How that is
done depends on NVE device type, and therefore add a per-NVE-type
operation.
Implement the operation for the sole NVE device type currently supported
by mlxsw, VXLAN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A replay of FDB needs to be performed so that the FDB entries existing
at the NVE device are offloaded. How the replay is done depends on NVE
device type, and therefore add a per-NVE-type operation.
Implement the operation for the sole NVE device type currently supported
by mlxsw, VXLAN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The notifier block will need to be passed to vxlan_fdb_replay() in a
follow-up patch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will add support for replay and for clearing of
offload marks. These are NVE type-sensitive operations, and to be able
to dispatch them properly, a FID needs to know what NVE type is attached
to it.
Therefore, track the NVE type at struct mlxsw_sp_fid. Extend
mlxsw_sp_fid_vni_set() to take it as an argument, and add
mlxsw_sp_fid_nve_type().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver unoffloads all FDB entries en bloc, it's inefficient to
send the switchdev notification one by one. Add a helper that unsets the
offload flag on FDB entries on a given bridge port and VLAN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver unoffloads all FDB entries en bloc, it's inefficient to
send the switchdev notification one by one. Add a helper that walks the
FDB table, unsetting the offload flag on RDST with a given VNI.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VXLAN device becomes relevant to a driver (such as when it is
attached to an offloaded bridge), the driver will generally need to walk
the existing FDB entries and offload them.
Add a function vxlan_fdb_replay() to call a given notifier block for
each FDB entry with a given VNI.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently two places that need to initialize the notifier info
structure, and one more is coming next when vxlan_fdb_replay() is
introduced. These three instances have / will have very similar code
that is easy to abstract away into a named function.
Add such function, vxlan_fdb_switchdev_notifier_info(), and call it from
vxlan_fdb_switchdev_call_notifiers() and vxlan_fdb_find_uc().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
net: aquantia: add RSS configuration
In this patchset few bugs related to RSS are fixed and RSS table and
hash key configuration is added.
We also do increase max number of HW rings upto 8.
v2: removed extra arg check
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of configuration of RSS hash key and RSS indirection table.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now RSS indirection table is initialized before setting up the number of
hw queues, consequently the table may be filled by non existing queues.
This patch moves the initialization when the number of hw queues is
known.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the upper limit of the hw queues up to 8.
This makes RSS better on multiheaded cpus.
This is a maximum AQC hardware supports in one traffic class.
The actual value is still limited by a number of available cpu cores.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set RSS indirection table and RSS hash key sizes to their real size.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
Pass extack to NETDEV_PRE_UP
Drivers may need to validate configuration of a device that's about to
be upped. An example is mlxsw, which needs to check the configuration of
a VXLAN device attached to an offloaded bridge. Should the validation
fail, there's currently no way to communicate details of the failure to
the user, beyond an error number.
Therefore this patch set extends the NETDEV_PRE_UP event to include
extack, if available.
There are three vectors through which NETDEV_PRE_UP invocation can be
reached. The two major ones are dev_open() and dev_change_flags(), the
last is then __dev_change_flags().
In patch #1, the first access vector, dev_open() is addressed. An extack
parameter is added and all users converted to use it.
Before addressing the second vector, two preparatory patches propagate
extack argument to the proximity of the dev_change_flags() call in VRF
and IPVLAN drivers. That happens in patches #2 and #3. Then in patch #4,
dev_change_flags() is treated similarly to dev_open().
Likewise in patch #5, __dev_change_flags() is extended.
Then in patches #6 and #7, the extack is finally propagated all the way
to the point where the notification is emitted.
This change allows particularly mlxsw (which already has code to
leverage extack if available) to communicate to the user error messages
regarding VXLAN configuration. In patch #8, add a test case that
exercises this code and checks that an error message is propagated.
For example:
local 192.0.2.17 remote 192.0.2.18 \
dstport 4789 nolearning noudpcsum tos inherit ttl 100
local 192.0.2.17 remote 192.0.2.18 \
dstport 4789 nolearning noudpcsum tos inherit ttl 100
Error: mlxsw_spectrum: Conflicting NVE tunnels configuration.
v2:
- Add David Ahern's tags.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a testsuite dedicated to testing extack propagation and related
functionality.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may need to validate configuration of a device that's about to
be upped. Should the validation fail, there's currently no way to
communicate details of the failure to the user, beyond an error number.
To mend that, change __dev_open() to take an extack argument and pass it
from __dev_change_flags() and dev_open(), where it was propagated in the
previous patches.
Change __dev_open() to call call_netdevice_notifiers_extack() so that
the passed-in extack is attached to the NETDEV_PRE_UP notifier.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to propagate extack through NETDEV_PRE_UP, add a new function
call_netdevice_notifiers_extack() that primes the extack field of the
notifier info. Convert call_netdevice_notifiers() to a simple wrapper
around the new function that passes NULL for extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass extack together with NETDEV_PRE_UP notifications, it's
necessary to route the extack to __dev_open() from diverse (possibly
indirect) callers. The last missing API is __dev_change_flags().
Therefore extend __dev_change_flags() with and extra extack argument and
update the two existing users.
Since the function declaration line is changed anyway, name the struct
net_device argument to placate checkpatch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass extack together with NETDEV_PRE_UP notifications, it's
necessary to route the extack to __dev_open() from diverse (possibly
indirect) callers. One prominent API through which the notification is
invoked is dev_change_flags().
Therefore extend dev_change_flags() with and extra extack argument and
update all users. Most of the calls end up just encoding NULL, but
several sites (VLAN, ipvlan, VRF, rtnetlink) do have extack available.
Since the function declaration line is changed anyway, name the other
function arguments to placate checkpatch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will extend dev_change_flags() with an extack
argument. Extend ipvlan_set_port_mode() to have that argument available
for the conversion.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will extend dev_change_flags() with an extack
argument. Extend cycle_netdev() to have that argument available for the
conversion.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass extack together with NETDEV_PRE_UP notifications, it's
necessary to route the extack to __dev_open() from diverse (possibly
indirect) callers. One prominent API through which the notification is
invoked is dev_open().
Therefore extend dev_open() with and extra extack argument and update
all users. Most of the calls end up just encoding NULL, but bond and
team drivers have the extack readily available.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2 goto labels are indented with a tab. remove the tabs and
keep the code style consistent.
Signed-off-by: Pedro Tammela <pctammela@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
Adjust MTU of DSA master interface
DSA makes use of additional headers to direct a frame in/out of a
specific port of the switch. When the slave interfaces uses an MTU of
1500, the master interface can be asked to handle frames with an MTU
of 1504, or 1508 bytes. Some Ethernet interfaces won't
transmit/receive frames which are bigger than their MTU.
Automate the increasing of the MTU on the master interface, by adding
to each tagging driver how much overhead they need, and then calling
dev_set_mtu() of the master interface to increase its MTU as needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA tagging of frames sent over the master interface to the switch
increases the size of the frame. Such frames can then be bigger than
the normal MTU of the master interface, and it may drop them. Use the
overhead information from the tagger to set the MTU of the master
device to include this overhead.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each DSA tag protocol needs to add additional headers to the Ethernet
frame in order to direct it towards a specific switch egress port. It
must also remove the head from a frame received from a
switch. Indicate the maximum size of these headers in the tag protocol
ops structure, so the core can take these overheads into account.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
caller has guaranted that rxhash is not zero
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tun flow entry 'updated' fields are written when receive
every packet. Thus if a flow is receiving packets from a
particular flow entry, it'll cause false-sharing with
all the other who has looked it up, so move it in its own
cache line
and update 'queue_index' and 'update' field only when
they are changed to reduce the cache false-sharing.
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Wang Li <wangli39@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack messages for failures in neigh_add and neigh_delete.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting LINK tolerance, node timer interval will be calculated
base on the LINK with lowest tolerance.
But when calculated, the old node timer interval only updated if current
setting value (tolerance/4) less than old ones regardless of number of
links as well as links' lowest tolerance value.
This caused to two cases missing if tolerance changed as following:
Case 1:
1.1/ There is one link (L1) available in the system
1.2/ Set L1's tolerance from 1500ms => lower (i.e 500ms)
1.3/ Then, fallback to default (1500ms) or higher (i.e 2000ms)
Expected:
node timer interval is 1500/4=375ms after 1.3
Result:
node timer interval will not being updated after changing tolerance at 1.3
since its value 1500/4=375ms is not less than 500/4=125ms at 1.2.
Case 2:
2.1/ There are two links (L1, L2) available in the system
2.2/ L1 and L2 tolerance value are 2000ms as initial
2.3/ Set L2's tolerance from 2000ms => lower 1500ms
2.4/ Disable link L2 (bring down its bearer)
Expected:
node timer interval is 2000ms/4=500ms after 2.4
Result:
node timer interval will not being updated after disabling L2 since
its value 2000ms/4=500ms is still not less than 1500/4=375ms at 2.3
although L2 is already not available in the system.
To fix this, we start the node interval calculation by initializing it to
a value larger than any conceivable calculated value. This way, the link
with the lowest tolerance will always determine the calculated value.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For instances using of_node_cmp, this has the side effect of now using
case sensitive comparisons. This should not matter for any FDT based
system which all of these are.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: netdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing high-bandwidth TCP streams with large windows,
high latency, and low jitter, netem consumes a lot of CPU cycles
doing rbtree rebalancing.
This patch uses a linear list/queue in addition to the rbtree:
if an incoming packet is past the tail of the linear queue, it is
added there, otherwise it is inserted into the rbtree.
Without this patch, perf shows netem_enqueue, netem_dequeue,
and rb_* functions among the top offenders. With this patch,
only netem_enqueue is noticeable if jitter is low/absent.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
net: bridge: convert multicast to generic rhashtable
The current bridge multicast code uses a custom rhashtable
implementation which predates the generic rhashtable API. Patch 01
converts it to use the generic kernel rhashtable which simplifies the
code a lot and removes duplicated functionality. The convert also makes
hash_elasticity obsolete as the generic rhashtable already has such
checks and has a fixed elasticity of RHT_ELASTICITY (16 currently) so we
emit a warning whenever elasticity is set and return RHT_ELASTICITY when
read (patch 03). Patch 02 converts the multicast code to use non-bh RCU
flavor as it was mixing bh and non-bh. Since now we have the generic
rhashtable which autoshrinks we can be more liberal with the default
hash maximum so patch 04 increases it to 4096 and moves it to a define in
br_private.h.
v3: add non-rcu br_mdb_get variant and use it where we have
multicast_lock, drop special hash_max handling and just set it where
needed and use non-bh RCU consistently (patch 02, new)
v2: send the latest version of the set which handles when IGMP snooping
is not defined, changes are in patch 01
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge's default hash_max was 512 which is rather conservative, now that
we're using the generic rhashtable API which autoshrinks let's increase
it to 4096 and move it to a define in br_private.h.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the bridge multicast uses the generic rhashtable interface we
can drop the hash_elasticity option as that is already done for us and
it's hardcoded to a maximum of RHT_ELASTICITY (16 currently). Add a
warning about the obsolete option when the hash_elasticity is set.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge multicast code has been using a mix of RCU and RCU-bh flavors
sometimes in questionable way. Since we've moved to rhashtable just use
non-bh RCU everywhere. In addition this simplifies freeing of objects
and allows us to remove some unnecessary callback functions.
v3: new patch
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge multicast code currently uses a custom resizable hashtable
which predates the generic rhashtable interface. It has many
shortcomings compared and duplicates functionality that is presently
available via the generic rhashtable, so this patch removes the custom
rhashtable implementation in favor of the kernel's generic rhashtable.
The hash maximum is kept and the rhashtable's size is used to do a loose
check if it's reached in which case we revert to the old behaviour and
disable further bridge multicast processing. Also now we can support any
hash maximum, doesn't need to be a power of 2.
v3: add non-rcu br_mdb_get variant and use it where multicast_lock is
held to avoid RCU splat, drop hash_max function and just set it
directly
v2: handle when IGMP snooping is undefined, add br_mdb_init/uninit
placeholders
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes updates to mlx5e netdevice driver
From Saeed, Remove trailing space of tx_pause ethtool stat
From Gal, Cleanup unused defines
From Aya, ethtool Support for configuring of RX hash fields
From Tariq, Improve ethtool private-flags code structure
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcCGc4AAoJEEg/ir3gV/o+4BsIALW3xpBhPAjKuBHYdFT/xLKB
ng9zsd43hl51WSsD/pzoi4ofk7ScvrsvAqoX123IhwAMGZ3lIaSc+qHGrkWuuwy6
byGMqXeXfs1wErbWUG5+iLfYWUa/aw+O4fuaLJCBl3Y3tpT8axaQ6RD66wRFKyJz
BR/Dal/Vfyzbaur0N0cl4vDcpgNZmR55Tej3uVNA9GwJyE4V3Cn1FmNC0SpVuLCw
cv+FXa4xs9StmvgGLUrqRnpRL5mdc0HaX3sMkuSbXFeLD8eNnhuJqR+l2nXmHWRz
3lYfR2uBan0D5GYrR3IUVHkImVhKIOHz3l4CR7GsN0Td+JpCIMuxrUd3Rg4IoDs=
=0f3t
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-12-04' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-12-04
This series includes updates to mlx5e netdevice driver
From Saeed, Remove trailing space of tx_pause ethtool stat
From Gal, Cleanup unused defines
From Aya, ethtool Support for configuring of RX hash fields
From Tariq, Improve ethtool private-flags code structure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
u32 to linkmode fixes
This patchset fixes issues found in the last patchset which converted
the phydev advertise etc, from a u32 to a linux bitmap. Most of the
issues are the result of clearing bits which should not of been
cleared. To make the API clearer, the idea from Heiner Kallweit was
used, with _mod_ to indicate the function modifies just the bits it
needs to, or _to_ to clear all bits and just set bit that need to be
set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MII_ADVERTISE register is modified by the IOCTL handler,
phydev->advertising needs recalculating. Use the _mod_ variant of
mii_adv_to_linkmode_adv_t so that bits outside of the advertise
registers are not cleared.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the if else code structure with a call to the helper
linkmode_mod_bit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a _mod_ variant of mii_lpa_to_linkmode_lpa_t. Use this to fix the
genphy_read_status() where the 1G link partner features are getting
lost.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_lpa_to_linkmode_lpa_t to mii_lpa_mod_linkmode_lpa_t to
indicate it modifies the passed linkmode bitmap, without clearing any
other bits.
Also, ensure bit are clear which the lpa indicates should not be set.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_stat1000_to_linkmode_lpa_t to
mii_stat1000_mod_linkmode_lpa_t to indicate it modifies the passed
linkmode bitmap, without clearing any other bits.
Add a helper to set/clear bits in a linkmode.
Use this helper to ensure bit are clear which the stat1000 indicates
should not be set.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_adv_to_linkmode_adv_t() clears all bits before setting it needs to
set. This means the freshly set Autoneg gets cleared.
Change the order, and add comments about it clearing the old content
of the bitmap.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code of private-flags setter.
Replace consecutive calls to mlx5e_handle_pflag with a loop
that uses a preset set of parameters.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
