The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NAND flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NAND flash, need to be disabled.
This patch is similar to "powerpc/85xx: p1022ds: disable the NOR flash node
if video is enabled", except that it disables the NAND flash node instead.
This PIXIS node needs to remain enabled because it is used by platform code
to switch into indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Host bridge hotplug
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos Kong)
Dynamic resource management
- Track bus number allocation (struct resource tree per domain) (Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oo/A
-----END PGP SIGNATURE-----
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
This gives the kernel a paravirtualized machine to target, without
requiring both sides to pretend to be targeting a specific board
that likely has little to do with the host in KVM scenarios. This
avoids the need to add new boards to QEMU just to be able to
run KVM on new CPUs.
As this is the first platform that can run with either e500v2 or
e500mc, CONFIG_PPC_E500MC is now a legitimately user configurable
option, so add a help text.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Similar to how the primary PCI bridge is identified by looking
for an isa subnode, we determine whether to apply uli exclusions
by looking for a uli subnode.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
prom_update_property() currently fails if the property doesn't
actually exist yet which isn't what we want. Change to add-or-update
instead of update-only, then we can remove a lot duplicated lines.
Suggested-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The
BSC9131 is integrated SoC that targets Femto base station market. It
combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte
shared L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel
Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE
UP/DL Channel processing, and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix
Inversion operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit
with ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network
acceleration including IEEE 1588. v2 hardware support and
virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single
port) and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD
support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
BSC9131RDB Overview
----------------------
BSC9131 SoC
1Gbyte DDR3 (on board DDR)
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
USB-ULPI
eTSEC1: Connected to RGMII PHY
eTSEC2: Connected to RGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Linux runs on e500v2 core and access some DSP peripherals like AIC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 96cc017c5b.
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In order to enable the DIU video controller on the P1022DS, the FPGA needs
to be switched to "indirect mode", where the localbus is disabled and
the FPGA is accessed via writes to localbus chip select signals CS0 and CS1.
To obtain the address of CS0 and CS1, the platform driver uses an "indirect
pixis mode" device tree node. This node assumes that the localbus 'ranges'
property is sorted in chip-select order. That is, reg value 0 maps to
CS0, reg value 1 maps to CS1, etc. This is how the 'ranges' property is
supposed to be arranged.
Unfortunately, the 'ranges' property is often mis-arranged, and not just on
the P1022DS. Linux normally does not care, since it does not program the
localbus. But the indirect-mode code on the P1022DS does care.
The "proper" fix is to have U-Boot fix the 'ranges' property, but this would
be too cumbersome. The names and 'reg' properties of all the localbus
devices would also need to be updated, and determining which localbus device
maps to which chip select is board-specific.
Instead, we determine the CS0/CS1 base addresses the same way that U-boot
does -- by reading the BRx registers directly and mapping them to physical
addresses. This code is simpler and more reliable, and it does not require
a U-boot or device tree change.
Since the indirect pixis device tree node is no longer needed, the node is
deleted from the DTS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reference board dates back to 2004, and is largely a legacy
EOL product. The MPC8560 is a pre e500v2 CPU. The SBC8548 is
a more modern, better e500v2 target for people to use as a
reference board with today's kernels, should they require one.
Removing support for it will also allow us to remove some
sbc8560 specific quirk handling in 8250 UART code, and some
MTD mapping support.
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1024rdb has the similar feature as the p1020rdb. Therefore, p1024rdb use
the same platform file as the p1/p2 rdb board.
Overview of P2020RDB platform
- DDR3 1G
- NOR flash 16M
- 3 Ethernet interfaces
- NAND Flash 32M
- SPI EEPROM 16M
- SD/MMC
- 2 USB ports
- 4 TDM ports
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
memblock_end_of_DRAM() returns end_address + 1, not end address.
While some code assumes that it returns end address.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The fixups are executed once the pci-device is found which is during
boot process so __init seems fine as long as the platform does not
support hotplug.
However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 46d026ac ("powerpc/85xx: consolidate of_platform_bus_probe calls")
replaced platform-specific of_device_id tables with a single function
that probes the most of the busses in 85xx device trees. If a specific
platform needed additional busses probed, then it could call
of_platform_bus_probe() again. Typically, the additional platform-specific
busses are children of existing busses that have already been probed.
of_platform_bus_probe() does not handle those child busses automatically.
Unfortunately, this doesn't actually work. The second (platform-specific)
call to of_platform_bus_probe() never finds any of the busses it's asked
to find.
To remedy this, the platform-specific of_device_id tables are eliminated,
and their entries are merged into mpc85xx_common_ids[], so that all busses
are probed at once.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the check for CONFIG_PPC_85xx and CONFIG_PPC_86xx from fsl_guts.h.
The check was originally intended to allow the same header file to
be used on 85xx and 86xx systems, even though the Global Utilities
register could be different. It turns out that they're not actually
different, and so the check is not necessary. In addition, neither
macro is defined for 64-bit e5500 kernels, so that causes a build
break.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Disintegrate asm/system.h for PowerPC.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cc: linuxppc-dev@lists.ozlabs.org
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
Remove FPGA(CADMUS) macros in code. Move it to dts.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable RapidIO and add rapidio and rmu nodes to dts.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a PCI bridge(Tsi310) between the MPC8548 and a VIA
southbridge chip.
The bootloader sets the PCI bridge to open a window from 0x0000
to 0x1fff on the PCI I/O space. But the kernel can't set the I/O
resource. In the routine pci_read_bridge_io(), if the base which
is read from PCI_IO_BASE is equal to zero, the routine don't set
the I/O resource of the child bus.
To allow the legacy I/O space on the VIA southbridge to be accessed,
use the fixup to fix the PCI I/O space of the PCI bridge.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc85xx_rdb and mpc85xx_mds have commom define of signal multiplex for qe, so
they need to go in common header, the patch abstract them to fsl_guts.h
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the "select PHYS_64BIT" from the Kconfig entry for the P1022DS,
so that large physical address support is a selectable option for non-CoreNet
reference boards.
The option is enabled in mpc85xx_[smp_]defconfig so that the default is
unchanged. However, now it can be deselected.
The P1022DS had this option defined because the default device tree for
this board uses 36-bit addresses. This had the side-effect of forcing
this option on for all boards that use mpc85xx_[smp_]defconfig. Some
users may want to disable this feature to create an optimized configuration
for boards with <= 2GB of RAM.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl_85xx_l2ctlr.o and fsl_85xx_cache_sram.o are built only
if CONFIG_FSL_85XX_CACHE_SRAM is defined. The driver that
qualifies and wants to make use of the CACHE SRAM's exported
API (i.e. a freescale net driver) should (be able to) select
this config option.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When the P1022's DIU video controller is active, the pixis must be accessed
in "indirect" mode, which uses localbus chip select addresses.
Switching between the DVI and LVDS monitor ports is handled by the pixis,
so that switching needs to be done via indirect mode.
This has the side-effect of no longer requiring U-Boot to enable the DIU.
Now Linux can enable the DIU all by itself.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1020utm-pc has the similar feature as the p1020rdb.
Therefore, p1020utm-pc use the same platform file as the p1/p2 rdb board.
Overview of P1020UTM-PC platform:
- DDR3 1GB
- NOR flash 32MB
- I2C EEPROM 256Kb
- eTSEC1 (RGMII PHY Atheros AR8021)
- eTSEC2 (SGMII PHY Vitesse VSC8221)
- eTSEC3 (RGMII PHY Atheros AR8021)
- SDHC
- 2 USB ports
- PCIe (Lane1 to dual SATA controller)
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p1020mbg-pc has the similar feature as the p1020rdb.
Therefore, p1020mbg-pc use the same platform file as the p1/p2 rdb board.
Overview of P1020MBG-PC platform:
- DDR3 2GB
- NOR flash 64MB
- I2C EEPROM 256Kb
- eTSEC1 (RGMII PHY) connected to VSC7385 L2 switch
- eTSEC2 (SGMII PHY)
- eTSEC3 (RGMII PHY)
- SDHC
- 2 USB ports
- 4 TDM ports
- PCIe (Lane1 to dual SATA controller)
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NOR flash, need to be disabled.
This also means that the localbus is not a 'simple-bus' any more, so remove
that string from the compatible node.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2020RDB-PC Board shares the same design(PCB) as P102x RDB style platforms.
The difference between this platform and the already existing P2020RDB
is mainly with respect to DDR. The P2020RDB-PC has a DDR3 memory.
The P2020RDB-PC also has a CPLD device connected to local bus.
The main differences from the P102x RDB-PC is 64-bit DDR and SYSCLK of
100Mhz.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The SERIAL_8250_EXTENDED option just enables access to other
less regularly used options, like SERIAL_8250_SHARE_IRQ.
Select it to get rid of this warning when selecting the child
option living underneath it.
warning: (FSL_SOC_BOOKE && SERIAL_8250_RM9K) selects
SERIAL_8250_SHARE_IRQ which has unmet direct dependencies
(HAS_IOMEM && SERIAL_8250_EXTENDED)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are two separate flags controlling whether or not the MPIC is
reset during initialization, which is completely unnecessary, and only
one of them can be specified in the device tree.
Also, most platforms in-tree right now do actually want to reset the
MPIC during initialization anyways, which means lots of duplicate code
passing the MPIC_WANTS_RESET flag.
Fix all of the callers which currently do not pass the MPIC_WANTS_RESET
flag to pass the MPIC_NO_RESET flag, then remove the MPIC_WANTS_RESET
flag and make the code reset the MPIC by default.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mpic->irq_count variable is only used as a software error-checking
limit to determine whether or not an IRQ number is valid. In board code
which does not manually specify an IRQ count to mpic_alloc(), i.e. 0, it
is automatically detected from the number of ISUs and the ISU size.
In practice, all hardware ends up with irq_count == num_sources, so all
of the runtime checks on mpic->irq_count should just check the value of
mpic->num_sources instead.
When platform hardware does not correctly report the number of IRQs,
which only happens on the MPC85xx/MPC86xx, the MPIC_BROKEN_FRR_NIRQS
flag is used to override the detected value of num_sources with the
manual irq_count parameter. Since there's no need to manually specify
the number of IRQs except in this case, the extra flag can be eliminated
and the test changed to "irq_count != 0".
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make all the irq_domain_ops structures in powerpc 'static const'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Each revmap type has different arguments for setting up the revmap.
This patch splits up the generator functions so that each revmap type
can do its own setup and the user doesn't need to keep track of how
each revmap type handles the arguments.
This patch also adds a host_data argument to the generators. There are
cases where the host_data pointer will be needed before the function returns.
ie. the legacy map calls the .map callback for each irq before returning.
v2: - Add void *host_data argument to irq_domain_add_*() functions
- fixed failure to compile
- Moved IRQ_DOMAIN_MAP_* defines into irqdomain.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
This patch drops the powerpc-specific irq_host structures and uses the common
irq_domain strucutres defined in linux/irqdomain.h. It also fixes all
the users to use the new structure names.
Renaming irq_host to irq_domain has been discussed for a long time, and this
patch is a step in the process of generalizing the powerpc virq code to be
usable by all architecture.
An astute reader will notice that this patch actually removes the irq_host
structure instead of renaming it. This is because the irq_domain structure
already exists in include/linux/irqdomain.h and has the needed data members.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Current linux-next compiled with mpc85xx_defconfig causes this:
arch/powerpc/platforms/85xx/p1022_ds.c:341:14: error: 'udbg_progress' undeclared here (not in a function)
Add include to fix this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current linux-next compiled with mpc85xx_defconfig causes this:
arch/powerpc/platforms/85xx/p1010rdb.c:41:14: error: 'np' undeclared (first use in this function)
arch/powerpc/platforms/85xx/p1023_rds.c:102:14: error: 'np' undeclared (first use in this function)
Introduced in:
commit 996983b75c
Author: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Date: Fri Dec 2 06:28:02 2011 +0000
powerpc/mpic: Search for open-pic device-tree node if NULL
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current linux-next compiled with mpc85xx_smp_defconfig causes this:
arch/powerpc/platforms/85xx/p1023_rds.c: In function 'mpc85xx_rds_pic_init':
arch/powerpc/platforms/85xx/p1023_rds.c:102:14: error: 'np' undeclared (first use in this function)
arch/powerpc/platforms/85xx/p1023_rds.c:102:14: note: each undeclared identifier is reported only once for each function it appears in
Introduced in:
commit 996983b75c
Author: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Date: Fri Dec 2 06:28:02 2011 +0000
powerpc/mpic: Search for open-pic device-tree node if NULL
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It turns out that there are only 2 in-tree platforms which use MPICs
which are not "primary": IBM Cell and PowerMac. To reduce the
complexity of the typical board setup code, invert the MPIC_PRIMARY bit
into MPIC_SECONDARY.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Almost all PowerPC platforms use a standard "open-pic" device node so
the mpic_alloc() function now accepts NULL for the device-node. This
will cause it to perform a default search with of_find_matching_node().
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead of using the open-coded "reg" property lookup and address
translation in mpic_alloc(), directly call of_address_to_resource().
This includes various workarounds for special cases which the naive
of_address_translate() does not.
Afterwards it is possible to remove the copiously copy-pasted calls to
of_address_translate() from the 85xx/86xx/powermac platforms.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes a bunch of "extern" declarations and CONFIG_SMP ifdefs.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cascade interrupt must run in hard interrupt context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
P1010RDB & P1023RDS can use the new mpc85xx_common_publish_devices().
Also move 'fsl,srio' into the list of standard buses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
85xx board files have a lot of duplication in *_publish_devices()/
*_declare_of_platform_devices() functions. Merge that into a single
function common to most of the boards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Separate handling of CPM2 PIC initialization to mpc85xx_cpm2_pic_init()
function.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update of_platform_bus_probe() RapidIO node to be compitable with
new RapidIO dts compatible property.
Signed-off-by: Kai Jiang <Kai.Jiang@freescale.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/p3060_qds.c: In function '__machine_initcall_p3060_qds_declare_of_platform_devices':
arch/powerpc/platforms/85xx/p3060_qds.c:73:1: error: implicit declaration of function 'declare_of_platform_devices'
declare_of_platform_devices should have been corenet_ds_publish_devices.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver for the Freescale P3060 QDS got added by commit 96cc017c5b
("[...] Add support for P3060QDS board"). Its Kconfig entry selects
MPC8xxx_GPIO. But at the time that driver got added MPC8xxx_GPIO was
already renamed to GPIO_MPC8XXX, by commit c68308dd50 ("gpio: move
mpc8xxx/512x gpio driver to drivers/gpio").
So make this driver select GPIO_MPC8XXX.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
P3060QDS Board Overview:
Memory subsystem:
- 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
- 128M Bytes NOR flash single-chip memory
- 16M Bytes SPI flash
- 8K Bytes AT24C64 I2C EEPROM
Ethernet:
- 4x1G + 4x1G/2.5G Ethernet controllers
- 2xRGMII + 1xMII, three VSC8641 PHYs on board
- Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C: Four I2C controllers
UART: Supports up to four UARTs
RapidIO: Supports two serial RapidIO ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is not strictly required, because this iterates over logical
cpus and they are not (currently) discontigous. But, it's cleaner
code and more obvious what is going on
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
None of the files touched here are modules, and they are not
exporting any symbols either -- so there is no need to be including
the module.h. Builds of all the files remains successful.
Even kernel/module.c does not need to include it, since it includes
linux/moduleloader.h instead.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (270 commits)
video: platinumfb: Add __devexit_p at necessary place
drivers/video: fsl-diu-fb: merge diu_pool into fsl_diu_data
drivers/video: fsl-diu-fb: merge diu_hw into fsl_diu_data
drivers/video: fsl-diu-fb: only DIU modes 0 and 1 are supported
drivers/video: fsl-diu-fb: remove unused panel operating mode support
drivers/video: fsl-diu-fb: use an enum for the AOI index
drivers/video: fsl-diu-fb: add several new video modes
drivers/video: fsl-diu-fb: remove broken screen blanking support
drivers/video: fsl-diu-fb: move some definitions out of the header file
drivers/video: fsl-diu-fb: fix some ioctls
video: da8xx-fb: Increased resolution configuration of revised LCDC IP
OMAPDSS: picodlp: add missing #include <linux/module.h>
fb: fix au1100fb bitrot.
mx3fb: fix NULL pointer dereference in screen blanking.
video: irq: Remove IRQF_DISABLED
smscufx: change edid data to u8 instead of char
OMAPDSS: DISPC: zorder support for DSS overlays
OMAPDSS: DISPC: VIDEO3 pipeline support
OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility setting
video/omap: fix build dependencies
...
Fix up conflicts in:
- drivers/staging/xgifb/XGI_main_26.c
Changes to XGIfb_pan_var()
- drivers/video/omap/{lcd_apollon.c,lcd_ldp.c,lcd_overo.c}
Removed (or in the case of apollon.c, merged into the generic
DSS panel in drivers/video/omap2/displays/panel-generic-dpi.c)
Normally logical and hard cpu ID are the same, however in same cases like
on the P3060 they may differ. Where the logical is 0..5, the hard id
goes 0,1,4..7. This can causes issues for places we utilize PIR to index
into array like in debug exception handlers for finding the exception
stack.
Move to setting up PIR with hard_smp_processor_id fixes the issue.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Standarize and document the FPGA nodes used on Freescale QorIQ reference
boards. There are different kinds of FPGAs used on the boards, but
only two are currently standard: "pixis", "ngpixis", and "qixis". Although
there are minor differences among the boards that have one kind of FPGA, most
of the functionality is the same, so it makes sense to create common
compatibility strings.
We also need to update the P1022DS platform file, because the compatible
string for its PIXIS node has changed. This means that older kernels are
not compatible with newer device trees. This is not a real problem, however,
since that particular function doesn't work anyway. When the DIU is active,
the PIXIS is in "indirect mode", and so cannot be accessed as a memory-mapped
device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 765342526246c97600e5344c0949824d94bb51c3 made some small changes to
IPI, message_pass in smp_ops was initialized to NULL for other platforms
but not for 85xx which causes us to always use the mpic for IPI's even
if we support doorbells in HW.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.
During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If CONFIG_PHYS_ADDR_T_64BIT is set, compilation of sbc8560 fails with
the following error:
arch/powerpc/platforms/85xx/sbc8560.c: In function ‘sbc8560_bdrstcr_init’:
arch/powerpc/platforms/85xx/sbc8560.c:286: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘resource_size_t’
Fix that by using %pR format instead of just printing the start of
resource.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
Change the string to check for CAMP mode boot on MPC85xx (eg. P2020) to match
the one in the corresponding dts files (p2020rdb_camp_core{0,1}.dts).
Without this fix the mpic is configured as in the SMP boot mode, which causes
the first core to report a protected source interrupt error for devices
of the other core and lock up.
Also add MPIC_SINGLE_DEST_CPU on both P2020 based architectures in CAMP
mode as suggested by Scott Wood. Thanks.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Instead of using ill-defined numbers (0, 1, and 2) for the monitor port, allow
the user to specify the port by name ("dvi", "lvds", or "dlvds"). This works
on the kernel command line, the module command-line, and the sysfs "monitor"
device.
Note that changing the monitor port does not currently work on the P1022DS,
because the code that talks to the PIXIS FPGA is broken.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Under the FSL Hypervisor we triggered a BUG_ON in mpc85xx_smp_init that
expected smp_ops.message_pass to be explicity set. However recent
changes allows smp_ops.message_pass to be NULL and handled by default
code. Thus the BUG_ON isn't relevant anymore.
Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
- Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
- Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale hypervisor does not allow guests to write to the timebase
registers (virtualizing the timebase register was deemed too complicated),
so don't try to synchronize the timebase registers when we're running
under the hypervisor.
This typically happens when kexec support is enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
I2C Board 128x8 bit memory
SD/MMC connector to interface with the SD memory card
2 SATA interface
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221 eCAN
Two DB-9 female connectors for Field bus interface UART
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To ensure that the DIU pixel clock will not be set to an invalid value,
clamp the PXCLK divider to the allowed range (2-255). This also acts as
a limiter for the pixel clock.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
e500mc cannot doze or nap due to an erratum (as well as having a
different mechanism than previous e500), but it has a "wait" instruction
that is similar to doze.
On 64-bit, due to the soft-irq-disable mechanism, the existing
book3e_idle should be used instead.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The platform file for the Freecale P1022DS reference board is not freeing
the ioremap() mapping of the PIXIS and global utilities nodes it creates.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the ePAPR-compliant Freescale hypervisor (aka "Topaz") on
the Freescale P3041DS, P4080DS, and P5020DS reference boards.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture. This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In cases like when the platform is used under hypervisor we will NOT
have an MPIC controller but still want doorbells setup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Several changes on PCIe support on P3041DS/P4080DS/P5020DS boards:
* Add support for "fsl,qoriq-pcie-v2.2" needed by P3041 & P5020
* Removed support for setting primary_phb_addr as we have no ISA need
* Add PCI controller to of_platform_bus_probe (for EDAC)
* Cleanup building w/SWIOTLB off on P4080DS (not stricly PCIe related)
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On many platforms (including pSeries), smp_ops->message_pass is always
smp_muxed_ipi_message_pass. This changes arch/powerpc/kernel/smp.c so
that if smp_ops->message_pass is NULL, it calls smp_muxed_ipi_message_pass
directly.
This means that a platform doesn't need to set both .message_pass and
.cause_ipi, only one of them. It is a slight performance improvement
in that it gets rid of an indirect function call at the expense of a
predictable conditional branch.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Consolidate the mux and demux of ipi messages into smp.c and call
a new smp_ops callback to actually trigger the ipi.
The powerpc architecture code is optimised for having 4 distinct
ipi triggers, which are mapped to 4 distinct messages (ipi many, ipi
single, scheduler ipi, and enter debugger). However, several interrupt
controllers only provide a single software triggered interrupt that
can be delivered to each cpu. To resolve this limitation, each smp_ops
implementation created a per-cpu variable that is manipulated with atomic
bitops. Since these lines will be contended they are optimialy marked as
shared_aligned and take a full cache line for each cpu. Distro kernels
may have 2 or 3 of these in their config, each taking per-cpu space
even though at most one will be in use.
This consolidation removes smp_message_recv and replaces the single call
actions cases with direct calls from the common message recognition loop.
The complicated debugger ipi case with its muxed crash handling code is
moved to debug_ipi_action which is now called from the demux code (instead
of the multi-message action calling smp_message_recv).
I put a call to reschedule_action to increase the likelyhood of correctly
merging the anticipated scheduler_ipi() hook coming from the scheduler
tree; that single required call can be inlined later.
The actual message decode is a copy of the old pseries xics code with its
memory barriers and cache line spacing, augmented with a per-cpu unsigned
long based on the book-e doorbell code. The optional data is set via a
callback from the implementation and is passed to the new cause-ipi hook
along with the logical cpu number. While currently only the doorbell
implemntation uses this data it should be almost zero cost to retrieve and
pass it -- it adds a single register load for the argument from the same
cache line to which we just completed a store and the register is dead
on return from the call. I extended the data element from unsigned int
to unsigned long in case some other code wanted to associate a pointer.
The doorbell check_self is replaced by a call to smp_muxed_ipi_resend,
conditioned on the CPU_DBELL feature. The ifdef guard could be relaxed
to CONFIG_SMP but I left it with BOOKE for now.
Also, the doorbell interrupt vector for book-e was not calling irq_enter
and irq_exit, which throws off cpu accounting and causes code to not
realize it is running in interrupt context. Add the missing calls.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we start a cpu we use smp_ops->kick_cpu(), which currently
returns void, it should be able to fail. Convert it to return
int, and update all uses.
Convert all the current error cases to return -ENOENT, which is
what would eventually be returned by __cpu_up() currently when
it doesn't detect the cpu as coming up in time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the spin table is located in the linear mapping (which can happen if
we have 4G or more of memory) we need to access the spin table via a
cacheable coherent mapping like we do on ppc32 (and do explicit cache
flush).
See the following commit for the ppc32 version of this issue:
commit d1d47ec6e6
Author: Peter Tyser <ptyser@xes-inc.com>
Date: Fri Dec 18 16:50:37 2009 -0600
powerpc/85xx: Fix SMP when "cpu-release-addr" is in lowmem
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patches below fixes a typo "singal" to "signal".
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds of_flat_dt_match() which tests a node for
compatibility with a list of values and converts the relevant powerpc
platform code to use it. This approach simplifies the board support
code a bit.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
The Freescale P1022DS has an on-chip video controller called the DIU, and a
driver for this device already exists. Update the platform file for the
P1022DS reference board to enable the driver, and update the defconfig for
Freescale MPC85xx boards to add the driver.
[Edited to resolve header add/add conflict and drop #define DEBUG.
-- broonie]
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The new e5500 core is similar to the e500mc core but adds 64-bit
support. We support running it in 32-bit mode as it is identical to the
e500mc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Like the MPC8610 HPCD, the P1022DS ASoC DMA driver probes on individual DMA
channel nodes, so the DMA controller nodes' compatible string must be
listed in p1022_ds_ids[] to work.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we do an mpic_reset_core we need to make sure the dcache is flushed.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make kexec_down_cpus atmoic since it will be incremented by all cores as
they are coming down.
Remove duplicate calls to mpc85xx_smp_kexec_down, now it's called by the
crash and normal kexec pathway only once.
Increase the timeout to wait for other cores to shutdown.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We no longer need to call this explicitly as a generic version is called
by default.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/built-in.o:(.toc1+0x18): undefined reference to `__early_start'
This is due to the 85xx/smp.c not handling the 64-bit side properly. We
need to set the entry point for secondary cores on ppc64e to
generic_secondary_smp_init instead of __early_start that we due on ppc32.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/p1022_ds.c:22:23: error: linux/lmb.h: No such file or directory
arch/powerpc/platforms/85xx/p1022_ds.c: In function 'p1022_ds_setup_arch':
arch/powerpc/platforms/85xx/p1022_ds.c💯 error: implicit declaration of function 'memblock_end_of_DRAM'
arch/powerpc/platforms/85xx/p1022_ds.c: At top level:
arch/powerpc/platforms/85xx/p1022_ds.c:147: error: 'udbg_progress' undeclared here (not in a function)
make[2]: *** [arch/powerpc/platforms/85xx/p1022_ds.o] Error 1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 99d8238f berobbed the for_each loop of its iterator! Let's be
nice and give it back, so it compiles for us.
CC: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce basic support for the Freescale P1022DS reference board, based on the
Freescale BSP for this board. This patch excludes the DIU, SSI, and MMC/SD
drivers. Only a 36-bit DTS is provided.
Update mpc86xx_smp_defconfig and mpc85xx_defconfig to support the P1022DS.
This means enabling 64-bit physical address support, increasing the maximum
zone order to 12 (to allow the DIU driver to allocate large chunks), and
clean up the audio options to disable the deprecated OSS support.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By default ti1520 bridge expects an input clock on CLOCK pin (to control
power chip). However on this boards CLOCK should be generated by PCI1520
itself. Add a quirk that enables internal 16 KHz clock generation on
this pin.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc85xx_mds_setup_arch() function is incomprehensible
and unmaintainable. Factor out all QE specific stuff into
mpc85xx_mds_qe_init() and mpc85xx_mds_reset_ucc_phys().
Also move QE stuff out of mpc85xx_mds_pic_init().
The diff is unreadable, but only because the code was so. ;-)
It should be better now, and less indented.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021 processors have no dedicated ROM to store the QE microcode,
so the fimrware is stored externally, and it is U-Boot responsibility
to load it. It might be that the board is booting without QE, e.g.
currently U-Boot doesn't support QE for P1021MDS boards, which means
that QE isn't initialized, and so the board hangs early at boot.
This patch fixes the issue by marking QE as disabled and checking the
state in the probing code. U-Boot should fixup the state if it
initialized the QE.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code inside '#ifdef CONFIG_QUICC_ENGINE' makes the
mpc85xx_mds_setup_arch() return early if no QE nodes present,
and so SWIOTLB is never initialized.
This patch fixes the issue by moving SWIOTLB code above
QE.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adds support for kexec on 85xx machines for the BookE platform.
Including support for SMP machines
Based off work from Maxim Uvarov <muvarov@mvista.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
via following scripts
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/lmb/memblock/g' \
-e 's/LMB/MEMBLOCK/g' \
$FILES
for N in $(find . -name lmb.[ch]); do
M=$(echo $N | sed 's/lmb/memblock/g')
mv $N $M
done
and remove some wrong change like lmbench and dlmb etc.
also move memblock.c from lib/ to mm/
Suggested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The doorbells use the content of the PIR register to match messages
from other CPUs. This may or may not be the same as our linux CPU
number, so using that as the "target" is no right.
Instead, we sample the PIR register at boot on every processor
and use that value subsequently when sending IPIs.
We also use a per-cpu message mask rather than a global array which
should limit cache line contention.
Note: We could use the CPU number in the device-tree instead of
the PIR register, as they are supposed to be equivalent. This
might prove useful if doorbells are to be used to kick CPUs out
of FW at boot time, thus before we can sample the PIR. This is
however not the case now and using the PIR just works.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently some MPC85xx and MPC86xx boards fail to build without
CONFIG_PCI:
arch/powerpc/platforms/fsl_uli1575.c: In function 'quirk_final_uli5249':
arch/powerpc/platforms/fsl_uli1575.c:234: error: implicit declaration of function 'pci_bus_for_each_resource'
arch/powerpc/platforms/fsl_uli1575.c:234: error: expected ';' before '{' token
cc1: warnings being treated as errors
arch/powerpc/platforms/fsl_uli1575.c:223: warning: unused variable 'dummy'
make[1]: *** [arch/powerpc/platforms/fsl_uli1575.o] Error 1
This patch fixes the issue by appending 'if PCI' condition when
selecting FSL_ULI1575 Kconfig symbol.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Interrupt controllers' hooks are executed in the atomic context, so
they are not permitted to sleep (with RT kernels non-raw spinlocks are
sleepable). So, socrates_fpga_pic_lock has to be a real (non-sleepable)
spinlock.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
This patch adds NOR Flash, LEDs and PIB support for MPC8568E-MDS
boards. Plus, move bcsr node into localbus node, and add bcsr5
gpio-controller node.
Some platform code modifications were also needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now we use printf style alignment there is no need to manually space
these fields.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent U-Boot commit 5ccd29c3679b3669b0bde5c501c1aa0f325a7acb caused
the "cpu-release-addr" device tree property to contain the physical RAM
location that secondary cores were spinning at. Previously, the
"cpu-release-addr" property contained a value referencing the boot page
translation address range of 0xfffffxxx, which then indirectly accessed
RAM.
The "cpu-release-addr" is currently ioremapped and the secondary cores
kicked. However, due to the recent change in "cpu-release-addr", it
sometimes points to a memory location in low memory that cannot be
ioremapped. For example on a P2020-based board with 512MB of RAM the
following error occurs on bootup:
<...>
mpic: requesting IPIs ...
__ioremap(): phys addr 0x1ffff000 is RAM lr c05df9a0
Unable to handle kernel paging request for data at address 0x00000014
Faulting instruction address: 0xc05df9b0
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2 P2020 RDB
Modules linked in:
<... eventual kernel panic>
Adding logic to conditionally ioremap or access memory directly resolves
the issue.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Reported-by: Dipen Dudhat <B09055@freescale.com>
Tested-by: Dipen Dudhat <B09055@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC85xx chips report the wrong value in feature reporting register,
and that causes the following oops:
Unable to handle kernel paging request for data at address 0x00000c00
Faulting instruction address: 0xc0019294
Oops: Kernel access of bad area, sig: 11 [#1]
MPC8569 MDS
Modules linked in:
[...]
NIP [c0019294] mpic_set_irq_type+0x2f0/0x368
LR [c0019124] mpic_set_irq_type+0x180/0x368
Call Trace:
[ef851d60] [c0019124] mpic_set_irq_type+0x180/0x368 (unreliable)
[ef851d90] [c007958c] __irq_set_trigger+0x44/0xd4
[ef851db0] [c007b550] set_irq_type+0x40/0x7c
[ef851dc0] [c0004a60] irq_create_of_mapping+0xb4/0x114
[ef851df0] [c0004af0] irq_of_parse_and_map+0x30/0x40
[ef851e20] [c0405678] fsl_of_msi_probe+0x1a0/0x328
[ef851e60] [c02e6438] of_platform_device_probe+0x5c/0x84
[...]
This is because mpic_alloc() assigns wrong values to
mpic->isu_{size,shift,mask}, and things eventually break when
_mpic_irq_read() is trying to use them.
This patch fixes the issue by enabling MPIC_BROKEN_FRR_NIRQS quirk.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
machine is compatible is an OF-specific call. It should have
the of_ prefix to protect the global namespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent U-Boot commit 5ccd29c3679b3669b0bde5c501c1aa0f325a7acb caused
the "cpu-release-addr" device tree property to contain the physical RAM
location that secondary cores were spinning at. Previously, the
"cpu-release-addr" property contained a value referencing the boot page
translation address range of 0xfffffxxx, which then indirectly accessed
RAM.
The "cpu-release-addr" is currently ioremapped and the secondary cores
kicked. However, due to the recent change in "cpu-release-addr", it
sometimes points to a memory location in low memory that cannot be
ioremapped. For example on a P2020-based board with 512MB of RAM the
following error occurs on bootup:
<...>
mpic: requesting IPIs ...
__ioremap(): phys addr 0x1ffff000 is RAM lr c05df9a0
Unable to handle kernel paging request for data at address 0x00000014
Faulting instruction address: 0xc05df9b0
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2 P2020 RDB
Modules linked in:
<... eventual kernel panic>
Adding logic to conditionally ioremap or access memory directly resolves
the issue.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Reported-by: Dipen Dudhat <B09055@freescale.com>
Tested-by: Dipen Dudhat <B09055@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The wrong variable was returned in the case of an error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Writing a driver using SCLPC on the MPC5200B I detected, that the
intspec arrays to map irqs to Linux virq cannot be const, because the
mapping and xlate functions only take non const pointers. All those
functions do not modify the intspec, so a const pointer could be used.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add basic support for the P4080 DS reference board. None of the data
path devices (ethernet, crypto, pme) are support at this time.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add power management controller nodes;
- Add interrupts for RTC nodes, the RTC interrupt may be used as a
wakeup source;
- Add sleep properties (DEVDISR bit mask) and sleep-nexus nodes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020 is another member of Freescale QorIQ series of processors.
It is an e500 based dual core SOC.
Being a scaled down version of P2020 it has following differences from P2020:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities(new controller).
From board perspective P1020RDB is same as P2020RDB.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch creates the dts files for each core and splits the devices
between the two cores for P2020RDB.
core0 has memory, L2, i2c, spi, dma1, usb, eth0, eth1, crypto,
global-util, pci0,
core1 has L2, dma2, eth0, pci1, msi.
MPIC is shared between two cores but each core will protect its
interrupts from other core by using "protected-sources" of mpic.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
get_irq_desc() is a powerpc-specific version of irq_to_desc(). That
is reason enough to remove it, but it also doesn't know about sparse
irq_desc support which irq_to_desc() does (when we enable it).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The following commit introduced a compile error since it removed
the implementation of smp_85xx_basic_setup:
commit 77c0a700c1
Author: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Fri Aug 28 14:25:04 2009 +1000
powerpc: Properly start decrementer on BookE secondary CPUs
Make it so that smp_ops probe() and setup_cpu() can be set to NULL.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves the code to start the decrementer on 40x and BookE into
a separate function which is now called from time_init() and
secondary_time_init(), before the respective clock sources are
registered. We also remove the 85xx specific code for doing it
from the platform code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now swiotlb_pci_dma_ops is identical to swiotlb_dma_ops; we can use
swiotlb_dma_ops with any devices. This removes swiotlb_pci_dma_ops.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds max_direct_dma_addr to struct dev_archdata to remove
addr_needs_map in struct dma_mapping_ops. It also converts
dma_capable() to use max_direct_dma_addr.
max_direct_dma_addr is initialized in pci_dma_dev_setup_swiotlb(),
called via ppc_md.pci_dma_dev_setup hook.
For further information:
http://marc.info/?t=124719060200001&r=1&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- Add gpio-controller node for BCSR17, it is used to control USB
speed and VBUS;
- Add timer node for QE GTM, needed for USB host;
- Add usb node itself;
- Add some probing code for BCSR GPIOs.
NOTE: QE USB doesn't work on prototype boards, but should work on
pilot boards if specs and schematics are correct, though we
don't have the pilot boards to actually test it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The existing fsl_rstcr_restart function is not applicable to the
mpc8560. The Global Utilities Block on this earlier CPU doesn't have
the control/reset register at 0xe00b0. This implements a board
specific reset function that uses the RCR(Reset Control Register) of
the sbc8560's EPLD to do a reset.
Signed-off-by: Liang Li <Liang.Li@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Those definitions are currently declared extern in the .c file where
they are used, move them to a header file instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linux isn't able to detect link changes on ethernet ports that were
used by U-Boot. This is because U-Boot wrongly clears interrupt
polarity bit (INTPOL, 0x400) in the extended status register (EXT_SR,
0x1b) of Marvell PHYs.
There is no easy way for PHY drivers to know IRQ line polarity (we
could extract it from the device tree and pass it to phydevs, but
that'll be quite a lot of work), so for now just reset the PHYs to
their default states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL RapidIO won't probe without a proper compatible entry. This
patch fixes the issue by adding fsl,rapidio-delta compatible to
mpc85xx_ids.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Match what other 85xx platforms do for of_platform_bus_probe and use
machine_device_initcall. This is one small step in killing of
ppc_md.init.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for X-ES single-board computers based on the Freescale
MPC85xx processors.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the platform-specific code for enabling SWIOTLB if needed on P2020DS,
MPC85xx DS, and MPC85xx MDS boards as they are capable of having >4G of
memory.
We determine if we need to enable swiotlb based on how much memory is in
the board and if it exceeds 4G or what we can map via PCI inbound
windows.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2020 is a dual e500v2 core based SOC with:
* 3 PCIe controllers
* 2 General purpose DMA controllers
* 2 sRIO controllers
* 3 eTSECS
* USB 2.0
* SDHC
* SPI, I2C, DUART
* enhanced localbus
* and optional Security (P2020E) security w/XOR acceleration
The p2020 DS reference board is pretty similar to the existing MPC85xx
DS boards and has a ULI 1575 connected on one of the PCIe controllers.
Signed-off-by: Ted Peters <Ted.Peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Select HAS_RAPIDIO symbol and add rio nodes for MPC8568E-MDS
and MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8569 is similiar to the MPC8568. It doubles the number of
QUICC Engine RISC cores from 2 to 4. Removes eTSECs, TLU and adds
the eSDHC controller.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Keep an unique machine def for the MPC8568 MDS board to handle some
subtle differences between the future MDS board. Also set the bcsrs in
setup_arch() only for mpc8568_mds because other mds has different bcsr
settings.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Impact: cleanup
It's unused, since about 1995. So remove all initialization of it in
preparation for actually removing the field.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Supported are Ethernet, serial console, I2C, I2C-based RTC and
temperature sensors, NOR and NAND flash, PCI, USB, CAN and Lime
display controller.
The multiplexing of FPGA interrupts onto PowerPC interrupt lines is
supported through our own fpga_pic interrupt controller driver.
For example the SJA1000 controller is level low sensitive connected to
fpga_pic line 2 and is routed to the second (of three) irq lines to
the CPU:
can@3,100 {
compatible = "philips,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 2>;
interrupts = <2 8 1>; // number, type, routing
interrupt-parent = <&fpga_pic>;
};
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use device tree to determine if we actually have an MPIC and use
CPU feature to decide if we should use doorbells for IPIs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
setup_irq(0, NULL) is broken as setup_irq() dereferences action
unconditionally.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a call to local_irq_restore in the normal exit case, so it would
seem that there should be one on an error return as well.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
expression E,E1,E2;
@@
local_irq_save(l);
... when != local_irq_restore(l)
when != spin_unlock_irqrestore(E,l)
when any
when strict
(
if (...) { ... when != local_irq_restore(l)
when != spin_unlock_irqrestore(E1,l)
+ local_irq_restore(l);
return ...;
}
|
if (...)
+ {local_irq_restore(l);
return ...;
+ }
|
spin_unlock_irqrestore(E2,l);
|
local_irq_restore(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The flag MPIC_WANTS_RESET shouldn't be set if we are doing cooperative
asymmetric MP. The second linux shouldn't reset the pic or the first
one gets very confused.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/mpc85xx_mds.c: In function 'board_fixups':
arch/powerpc/platforms/85xx/mpc85xx_mds.c:244: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
arch/powerpc/platforms/85xx/mpc85xx_mds.c:250: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added 85xx specifc smp_ops structure. We use ePAPR style boot release
and the MPIC for IPIs at this point.
Additionally added routines for secondary cpu entry and initializtion.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale implementation of MPIC only allows a single CPU destination
for non-IPI interrupts. We add a flag to the mpic_init to distinquish
these variants of MPIC. We pull in the irq_choose_cpu from sparc64 to
select a single CPU as the destination of the interrupt.
This is to deal with the fact that the default smp affinity was
changed by commit 1840475676 ("genirq:
Expose default irq affinity mask (take 3)") to be all CPUs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Most of the platforms were printing the size of the memory
in their show_cpuinfo implementations. This moves that to
the common show_cpuinfo, so that all 32-bit platforms will
now print the size of memory. I also update the code
to deal with the fact that total_memory is now a phys_addr_t.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Modify the Kconfig so that Freescale QUICC Engine (QE) support is a selectable
option, thereby allowing users to compile kernels without any QE support.
The drawback is that QE support is now disabled by default on platforms that
have a QE, and so a defconfig is needed to enable QE and QE devices (like
UCC GETH). Fortunately, all the current relevant defconfigs do that already.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For many of the embedded boards, "model" and "Machine" are printing
the same thing; remove the redundant code and allow the generic
show_cpuinfo to print the model information.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is just a parallel of a5dc66e2ab
applied to the sbc8560 board.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them. Add same to platform probe code.
This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.
also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With arch/ppc gone and all in kernel users of CONFIG_PPC_CPM_NEW_BINDING
fixed up we dont have need for the Kconfig option anymore.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Get rid of uses_fsl_uli_m1575, it does not scale for all cases.
Instead, let's explicitly use machine_is() for each fixup.
- Factor out MPC8610HPCD quirks to fsl_uli1575, and protect them with
machine_is(). One step closer to multiplatform kernels.
- Actually use fsl_uli1575 on MPC8610HPCD, so RTC quirk will be applied.
- RTC quirk applies to all boards though, so no machine_is() checks.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Choosing PCI or not at config time is allowed on some
platforms via an if expression in arch/powerpc/Kconfig.
To add a new platform with PCI support selectable at
config time, you must change the if expression. This
patch makes this easier by changing:
bool "PCI support" if <long expression>
to
bool "PCI support" if PPC_PCI_CHOICE
and adding select PPC_PCI_CHOICE to all the config nodes that
were previously in the PCI if expression.
Platforms with unconditional PCI support continue to
just select PCI in their config nodes.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the "uninitialized use" compile warning and avoid potential
runtime issue.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Publish the devices listed in dts under SOC as of_device for 85xx_cds
platform. The devices are needed by the 85xx EDAC driver.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These issues were reported by Stephen Rothwell for another 85xx board
port and pointed out by Chen Gong as issues in the DS port.
* mpic OF node reference counting was off
* of_device_id struct should be marked as __initdata
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ports B and C pins programming is changed to get SCC2 UART and FCC3
ethernet work.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Like for the TQM5200, the vendor prefix "tqc," is now used for all
TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the
corresponding DTS files.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC85xx MDS board requires some board level tweaks of the PHYs that
either the eTSEC (gianfar) or UCC ethernet controllers are connected to.
Its possible to build the phylib as a module, however this breaks the
board level fix ups because phy_read and phy_write are not available
if we build as a module.
So we unconditionally select PHYLIB to ensure its built into the kernel
if we are building in MPC85xx MDS support. This was determined to be
the easiest soultion even though it prevents the user from removing
PHYLIB support if they decide they don't want it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enabled MSI on 8544ds and 8572ds board.
So far only one MSI interrupt can generate on 8544 board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following adds local bus, flash and MTD partition nodes for
sbc8548. As well, a compatible field for the soc node, so that
of_platform_bus_probe() will pick it up.
Something that is provided through this newly added epld node
is the Hardware Revision which is now being utilized.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 8568 MDS needs some configuration changes to the PHY in order to
work properly. These are done in the firmware, normally, but Linux
shouldn't need to rely on the firmware running such things (someone
could disable the PHY support in the firmware to save space, for instance).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/mpc85xx_ads.c: In function ‘init_ioports’:
arch/powerpc/platforms/85xx/mpc85xx_ads.c:168: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
