This driver is required to work around several hardware bugs in the PCIe
controller.
The SMP8759 does not support legacy interrupts or IO space.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[bhelgaas: add CONFIG_BROKEN dependency, various cleanups]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/host-rockchip:
PCI: rockchip: Use normal register bank for config accessors
PCI: rockchip: Use local struct device pointer consistently
PCI: rockchip: Check for clk_prepare_enable() errors during resume
MAINTAINERS: Remove Wenrui Li as Rockchip PCIe driver maintainer
PCI: rockchip: Configure RC's MPS setting
PCI: rockchip: Reconfigure configuration space header type
PCI: rockchip: Split out rockchip_pcie_cfg_configuration_accesses()
PCI: rockchip: Move configuration accesses into rockchip_pcie_cfg_atu()
PCI: rockchip: Rename rockchip_cfg_atu() to rockchip_pcie_cfg_atu()
PCI: rockchip: Control vpcie0v9 for system PM
Rockchip's RC has two banks of registers for the root port: a normal bank
that is strictly compatible with the PCIe spec, and a privileged bank that
can be used to change RO bits of root port registers.
When probing the RC driver, we use the privileged bank to do some basic
setup work as some RO bits are hw-inited to wrong value. But we didn't
change to the normal bank after probing the driver.
This leads to a serious problem when the PME code tries to clear the PME
status by writing PCI_EXP_RTSTA_PME to the register of PCI_EXP_RTSTA. Per
PCIe 3.0 spec, section 7.8.14, the PME status bit is RW1C. So the PME code
is doing the right thing to clear the PME status but we find the RC doesn't
clear it but actually setting it to one. So finally the system trap in
pcie_pme_work_fn() as PCI_EXP_RTSTA_PME is true now forever. This issue
can be reproduced by booting kernel with pci=nomsi.
Use the normal register bank for the PCI config accessors. The privileged
bank is used only internally by this driver.
Fixes: e77f847d ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Brian Norris <briannorris@chromium.org>
* pci/host-hv:
PCI: hv: Use vPCI protocol version 1.2
PCI: hv: Add vPCI version protocol negotiation
PCI: hv: Temporary own CPU-number-to-vCPU-number infra
PCI: hv: Use page allocation for hbus structure
PCI: hv: Fix comment formatting and use proper integer fields
of_device_ids are not supposed to change at runtime. All functions working
with of_device_ids provided by <linux/of.h> work with const of_device_ids.
So mark the non-const structs as const.
File size before:
text data bss dec hex filename
195 600 0 795 31b drivers/pci/host/pcie-xilinx.o
File size after constify xilinx_pcie_of_match:
text data bss dec hex filename
595 184 0 779 30b drivers/pci/host/pcie-xilinx.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add spinlock for protecting legacy mask register
- Few wifi end points which only support legacy interrupts, performs
hardware reset functionalities after disabling interrupts by invoking
disable_irq() and then re-enable using enable_irq(), they enable hardware
interrupts first and then virtual IRQ line later.
- The legacy IRQ line goes low only after DEASSERT_INTx is received. As
the legacy IRQ line is high immediately after hardware interrupts are
enabled but virq of EP is still in disabled state and EP handler is never
executed resulting no DEASSERT_INTx. If dummy IRQ chip is used,
interrupts are not masked and system hangs with CPU stall.
- Add IRQ chip functions instead of dummy IRQ chip for legacy interrupts.
- Legacy interrupts are level sensitive, so using handle_level_irq() is
more appropriate as it is masks interrupts until Endpoint handles
interrupts and unmasks interrupts after Endpoint handler is executed.
- Legacy interrupts are level triggered, virtual IRQ line of EndPoint shows
as edge in /proc/interrupts.
- Set IRQ flags of virtual IRQ line of EP to level triggered at the time of
mapping.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Recent __call_srcu() changes have exposed that we need to cleanup SRCU
structures after pci_stop_root_bus() calls into vmd_msi_free().
Fixes: 3906b91844 ("PCI: vmd: Use SRCU as a local RCU to prevent delaying global RCU")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Cc: <stable@vger.kernel.org> # 4.11
VMD domains are allocated starting at 0x10000, not 0x1000 as the comment
said. Correct the comment and add a reference to the ACPI spec for _SEG.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI host bridge found on Tegra SoCs doesn't require the MSI target
address to be backed by physical system memory. Writes are intercepted
within the controller and never make it to the memory pointed to.
Since no actual system memory is required, remove the allocation of a
single page and hardcode the MSI target address with a special address that
maps to the last 4 KiB page within the range that is reserved for system
memory and memory-mapped I/O in the FPCI address map.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
The MSI target address can reside beyond the 32-bit boundary on devices
with more than 2 GiB of system memory. The PCI host bridge on Tegra can
easily support 64-bit addresses, so make sure to pass the upper 32 bits of
the target address to endpoints when allocating MSI entries.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
We have a local "struct device *dev" in rockchip_pcie_probe(). Use it
consistently throughout the function. No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
The default value of MPS for RC is 128 bytes, but actually it could support
256 bytes. So this patch fixes this issue.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe base specification (Revision 3.1a), section 7.5.3, type 1
configuration space header should be used when accessing PCIe switch. So
we need to reconfigure the header according to the bus number we are
accessing. Otherwise we could not visit the buses behind the switch.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need to reconfigure the header type later, so split out a new function.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Configuration accesses is also part of ATU settings, so let's keep all of
them inside rockchip_pcie_cfg_atu().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename rockchip_cfg_atu() to keep the name consistent with other functions
in pcie-rockchip.c.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
vpcie0v9 is used for PHY, so we could disable it as we don't need PHY to
work then in S3 if folks assign it DT. But we should note that there is a
side effect that we could not support beacon wakeup if we disable vpcie0v9
for aggressive power-saving.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
of_device_ids are not supposed to change at runtime. All functions working
with of_device_ids provided by <linux/of.h> work with const of_device_ids.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Update the Hyper-V vPCI driver to use the Server-2016 version of the vPCI
protocol, fixing MSI creation and retargeting issues.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Hyper-V vPCI offers different protocol versions. Add the infra for
negotiating the one to use.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
To ease parallel effort to centralize CPU-number-to-vCPU-number conversion,
temporarily stand up own version, file-local hv_tmp_cpu_nr_to_vp_nr().
Once the changes have merged, this work-around can be removed, and the
calls replaced with hv_cpu_number_to_vp_number().
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
The hv_pcibus_device structure contains an in-memory hypercall argument
that must not cross a page boundary. Allocate the structure as a page to
ensure that.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Fix comment formatting and use proper integer fields.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Similar as commit 8ff0ef996c ("PCI: host: Mark PCIe/PCI (MSI) IRQ cascade
handlers as IRQF_NO_THREAD"), we should mark PCIe/PCI (MSI) IRQ cascade
handlers in designware, qcom, and vmd as IRQF_NO_THREAD explicitly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com> # vmd
Acked-by: Jingoo Han <jingoohan1@gmail.com> # pcie-designware-plat.c
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Add map/swizzle IRQs hooks to the xilinx-nwl PCI host driver to move the
IRQ allocation into core code and stop relying on arch-specific callbacks.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Add map/swizzle IRQs hooks to the rockchip PCI host driver to move the IRQ
allocation into core code and stop relying on arch-specific callbacks.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wenrui Li <wenrui.li@rock-chips.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Add map/swizzle IRQs hooks to the xgene PCI host driver to move the IRQ
allocation into core code and stop relying on arch-specific callbacks.
Tested-by: Khuong Dinh <kdinh@apm.com> # with e1000e
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI altera host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ley Foon Tan <lftan@altera.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI versatile host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: folded in typo fix from Arnd Bergmann <arnd@arndb.de>:
http://lkml.kernel.org/r/20170621215323.3921382-4-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rob Herring <robh@kernel.org>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI host-common bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI ftpci100 host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI iproc host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI rcar host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Simon Horman <horms@verge.net.au>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI xilinx host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation
Drop pci_fixup_irqs() usage from PCI tegra host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI xilinx-nwl host code to pci_scan_root_bus_bridge() to improve
the PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI rockchip host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wenrui Li <wenrui.li@rock-chips.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI host-common code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI xgene host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Tested-by: Khuong Dinh <kdinh@apm.com> # with e1000e
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI xilinx host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Michal Simek <michal.simek@xilinx.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI altera host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ley Foon Tan <lftan@altera.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI versatile host code to pci_scan_root_bus_bridge() to improve
the PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: folded in fix from Arnd Bergmann <arnd@arndb.de>:
http://lkml.kernel.org/r/20170621215323.3921382-3-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rob Herring <robh@kernel.org>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI iproc host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI rcar host code to pci_scan_root_bus_bridge() to improve the PCI
root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Simon Horman <horms@verge.net.au>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI aardvark host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With the introduction of pci_scan_root_bus_bridge() there is no need to
export pci_register_host_bridge() to other kernel subsystems other than the
PCI compilation unit that needs it.
Make pci_register_host_bridge() static to its compilation unit and convert
the existing drivers usage over to pci_scan_root_bus_bridge().
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
When probing the PCI host controller driver, if an error occurs, the probe
function code does not free memory allocated for the struct pci_host_bridge
resulting in memory leakage.
Move the struct pci_host_bridge allocation over to the respective devm
interface to fix the issue.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
When probing the PCI host controller driver, if an error occurs, the probe
function code does not free memory allocated for the struct pci_host_bridge
resulting in memory leakage.
Move the struct pci_host_bridge allocation over to the respective devm
interface to fix the issue.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Current ftpci100 driver host bridge controller driver requires struct
pci_bus to be created in order to mask and clear IRQs using standard PCI
bus config accessors.
This struct pci_bus dependency is fictitious and burdens the driver with
unneeded constraints (eg to use separate APIs to create and scan the root
bus).
Add PCI raw config space accessors to PCIe ftpci100 driver and remove the
fictitious struct pci_bus dependency.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: folded in raw PCI read accessor from
http://lkml.kernel.org/r/20170621162651.25315-1-linus.walleij@linaro.org
The clock piece of the above posting goes with the separate "Add clock
handling" patch.]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The current iproc driver host bridge controller driver requires struct
pci_bus to be created in order to carry out PCI link checks with standard
PCI config space accessors.
This struct pci_bus dependency is fictitious and burdens the driver with
unneeded constraints (eg to use separate APIs to create and scan the root
bus).
Add PCI raw config space accessors to the iproc driver and remove the
fictitious struct pci_bus dependency.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
The nwl_pcie_enable_msi() second parameter (ie "bus") is unused and creates
a fake dependency on the struct pci_bus that need not exist.
Remove it.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Use the fwnode to create a named domain so diagnosis works.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.379861978@linutronix.de
Many PCI host controller drivers aren't prepared to have their devices
unbound from them forcefully (e.g., through /sys/.../<driver>/unbind), as
they don't provide any driver .remove callback, where they'd detach the
root bus, release resources, etc. Keeping the driver built in (i.e., not a
loadable module) is not enough; and providing no .remove callback just
means we don't do any teardown.
To rule out the possibility of unbinding a device via sysfs, we need to set
the ".suppress_bind_attrs" field.
I found the suspect drivers via the following search:
git grep -l platform_driver $(git grep -L -e '\.remove' -e suppress_bind_attrs drivers/pci/)
Then I inspected them to ensure that
(a) they set up a PCI bus in their probe() and
(b) they don't have a remove() callback for undoing the setup
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/msi:
PCI/MSI: Use dev_printk() when possible
of/pci: Remove unused MSI controller helpers
PCI: mvebu: Remove useless MSI enabling code
PCI: aardvark: Move to MSI handling using generic MSI support
PCI/MSI: Make pci_msi_shutdown() and pci_msix_shutdown() static
PCI/MSI: Stop disabling MSI/MSI-X in pci_device_shutdown()
* pci/ioremap:
PCI: versatile: Update PCI config space remap function
PCI: keystone-dw: Update PCI config space remap function
PCI: layerscape: Update PCI config space remap function
PCI: hisi: Update PCI config space remap function
PCI: tegra: Update PCI config space remap function
PCI: xgene: Update PCI config space remap function
PCI: armada8k: Update PCI config space remap function
PCI: designware: Update PCI config space remap function
PCI: iproc-platform: Update PCI config space remap function
PCI: qcom: Update PCI config space remap function
PCI: rockchip: Update PCI config space remap function
PCI: spear13xx: Update PCI config space remap function
PCI: xilinx-nwl: Update PCI config space remap function
PCI: xilinx: Update PCI config space remap function
PCI: ECAM: Map config region with pci_remap_cfgspace()
PCI: Implement devm_pci_remap_cfgspace()
devres: fix devm_ioremap_*() offset parameter kerneldoc description
ARM: Implement pci_remap_cfgspace() interface
ARM64: Implement pci_remap_cfgspace() interface
linux/io.h: Add pci_remap_cfgspace() interface
PCI: Remove __weak tag from pci_remap_iospace()
* pci/host-rockchip:
PCI: rockchip: Modularize
PCI: Export pci_remap_iospace() and pci_unmap_iospace()
PCI: rockchip: Add remove() support
PCI: rockchip: Set PCI_EXP_LNKSTA_SLC in the Root Port
PCI: rockchip: Advertise 128-byte Read Completion Boundary support
PCI: rockchip: Make 'return 0' more obvious in probe()
PCI: rockchip: Unindent rockchip_pcie_set_power_limit()
PCI: rockchip: Handle regulator_get_current_limit() failure correctly
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_ioremap_nopost* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rob Herring <robh@kernel.org>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use correct memory mapping attributes to map config space
regions to enforce configuration space non-posted writes behaviour.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_pci_remap_cfg* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_pci_remap_cfg* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_pci_remap_cfg* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wenrui Li <wenrui.li@rock-chips.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_pci_remap_cfg* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_pci_remap_cfg* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Now that we've exported pci_remap_iospace() and added proper remove()
support, there's no reason this can't be a loadable module.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Currently, if we try to unbind the platform device, the remove will
succeed, but the removal won't undo most of the registration, leaving
partially-configured PCI devices in the system.
This allows, for example, a simple 'lspci' to crash the system, as it will
try to touch the freed (via devm_*) driver structures, e.g., on RK3399:
# echo f8000000.pcie > /sys/bus/platform/drivers/rockchip-pcie/unbind
# lspci
So let's implement device remove().
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
refcount_t type and corresponding API should be used instead of atomic_t
when the variable is used as a reference counter. This allows to avoid
accidental refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
All platforms using Rockchip use a common clock for the Root Port and the
slot connected to it. Indicate this by setting the Slot Clock Configuration
(PCI_EXP_LNKSTA_SLC) bit in the Root Port's Link Status.
Per the Implementation Note in the spec (PCIe r3.1, sec 7.8.7), if the
downstream component also sets PCI_EXP_LNKSTA_SLC, software may set the
Common Clock Configuration (PCI_EXP_LNKCTL_CCC) bits on both ends of the
Link. This is done by pcie_aspm_configure_common_clock().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: jeffy.chen <jeffy.chen@rock-chips.com>
The memory allocation here needs to be non-blocking. Fix the issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org>
When we have 32 or more CPUs in the affinity mask, we should use a special
constant to specify that to the host. Fix this issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org>
Rockchip Root Ports support either 64 or 128 byte Read Completion Boundary
(RCB). Set the RCB bit in the Link Control register to indicate this.
A 128 byte RCB significantly improves performance of NVMe with libaio.
[bhelgaas: changelog]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
SZ_16M PEM resource size includes PEM-specific register and its children
resources. Reservation of the whole SZ_16M range leads to child device
driver failure when pcieport driver is requesting resources:
pcieport 0004:1f:00.0: can't enable device: BAR 0 [mem 0x87e0c0f00000-0x87e0c0ffffff 64bit] not claimed
So we cannot reserve full 16M here and instead we want to reserve
PEM-specific register only which is SZ_64K.
At the end increase PEM resource to SZ_16M since this is what
thunder_pem_init() call expects for proper initialization.
Fixes: 9abb27c759 ("PCI: thunder-pem: Add legacy firmware support for Cavium ThunderX host controller")
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.10+
It seems on later Armada 38x, the slot clock configuration bit is not
read-only, but can be written. This means that our RW1C protection ends up
clearing this bit when the link control register is written.
Adjust the mask so that we only avoid writing '1' bits to the RW1C bits of
this register (bits 15 and 14 of the link status) rather than masking out
all the status register bits.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a host bridge driver for the Faraday Technology FPPCI100 host bridge,
used for Cortina Systems Gemini SoC (SL3516) PCI Host Bridge.
This code is inspired by the out-of-tree OpenWRT patch and then extensively
rewritten for device tree and using the modern helpers to cut down and
modernize the code to all new PCI frameworks. A driver exists in U-Boot as
well.
Tested on the ITian Square One SQ201 NAS with the following result in the
boot log (trimmed to relevant parts):
OF: PCI: host bridge /soc/pci@50000000 ranges:
OF: PCI: IO 0x50000000..0x500fffff -> 0x00000000
OF: PCI: MEM 0x58000000..0x5fffffff -> 0x58000000
ftpci100 50000000.pci: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0x58000000-0x5fffffff]
ftpci100 50000000.pci:
DMA MEM1 BASE: 0x0000000000000000 -> 0x0000000007ffffff config 00070000
ftpci100 50000000.pci:
DMA MEM2 BASE: 0x0000000000000000 -> 0x0000000003ffffff config 00060000
ftpci100 50000000.pci:
DMA MEM3 BASE: 0x0000000000000000 -> 0x0000000003ffffff config 00060000
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: of_irq_parse_pci() failed with rc=-22
pci 0000:00:0c.0: BAR 0: assigned [mem 0x58000000-0x58007fff]
pci 0000:00:09.2: BAR 0: assigned [mem 0x58008000-0x580080ff]
pci 0000:00:09.0: BAR 4: assigned [io 0x1000-0x101f]
pci 0000:00:09.1: BAR 4: assigned [io 0x1020-0x103f]
pci 0000:00:09.0: enabling device (0140 -> 0141)
pci 0000:00:09.0: HCRESET not completed yet!
pci 0000:00:09.1: enabling device (0140 -> 0141)
pci 0000:00:09.1: HCRESET not completed yet!
pci 0000:00:09.2: enabling device (0140 -> 0142)
rt61pci 0000:00:0c.0: enabling device (0140 -> 0142)
ieee80211 phy0: rt2x00_set_chip: Info - Chipset detected -
rt: 2561, rf: 0003, rev: 000c
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:09.2: EHCI Host Controller
ehci-pci 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:09.2: irq 125, io mem 0x58008000
ehci-pci 0000:00:09.2: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:09.0: UHCI Host Controller
uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:09.0: HCRESET not completed yet!
uhci_hcd 0000:00:09.0: irq 123, io base 0x00001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
uhci_hcd 0000:00:09.1: UHCI Host Controller
uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:09.1: HCRESET not completed yet!
uhci_hcd 0000:00:09.1: irq 124, io base 0x00001020
hub 3-0:1.0: USB hub found
hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
scsi 0:0:0:0: Direct-Access USB Flash Disk 1.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 7900336 512-byte logical blocks: (4.04 GB/3.77 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] No Caching mode page found
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI removable disk
ieee80211 phy0: rt2x00lib_request_firmware: Info -
Loading firmware file 'rt2561s.bin'
ieee80211 phy0: rt2x00lib_request_firmware: Info -
Firmware detected - version: 0.8
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
$ lspci
00:00.0 Class 0600: 159b:4321
00:09.2 Class 0c03: 1106:3104
00:09.0 Class 0c03: 1106:3038
00:09.1 Class 0c03: 1106:3038
00:0c.0 Class 0280: 1814:0301
$ cat /proc/interrupts
CPU0
123: 0 PCI 0 Edge uhci_hcd:usb2
124: 0 PCI 1 Edge uhci_hcd:usb3
125: 159 PCI 2 Edge ehci_hcd:usb1
126: 1082 PCI 3 Edge rt61pci
$ cat /proc/iomem
50000000-500000ff : /soc/pci@50000000
58000000-5fffffff : Gemini PCI MEM
58000000-58007fff : 0000:00:0c.0
58000000-58007fff : 0000:00:0c.0
58008000-580080ff : 0000:00:09.2
58008000-580080ff : ehci_hcd
The EHCI USB hub works fine; I can mount and manage files and the IRQs just
keep ticking up. I can issue iwlist wlan0 scanning and see all the WLANs
here. I don't have wpa_supplicant so have not tried connecting to them.
[bhelgaas: fold in %pap change from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Janos Laube <janos.dev@gmail.com>
CC: Paulius Zaleckas <paulius.zaleckas@gmail.com>
CC: Hans Ulli Kroll <ulli.kroll@googlemail.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Feng-Hsin Chiang <john453@faraday-tech.com>
CC: Greentime Hu <green.hu@gmail.com>
A PCI_EJECT message can arrive at the same time we are calling
pci_scan_child_bus() in the workqueue for the previous PCI_BUS_RELATIONS
message or in create_root_hv_pci_bus(). In this case we could potentially
modify the bus from multiple places.
Properly lock the bus access.
Thanks Dexuan Cui <decui@microsoft.com> for pointing out the race condition
in create_root_hv_pci_bus().
Reported-by: Xiaofeng Wang <xiaofwan@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
hv_pci_devices_present() is called in hv_pci_remove() when we remove a PCI
device from the host, e.g., by disabling SR-IOV on a device. In
hv_pci_remove(), the bus is already removed before the call, so we don't
need to rescan the bus in the workqueue scheduled from
hv_pci_devices_present().
By introducing bus state hv_pcibus_removed, we can avoid this situation.
Reported-by: Xiaofeng Wang <xiaofwan@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
There's no way to get here with 'err != 0'. Just return 0 to be more
obvious and prevent future changes from accidentally erroring out here
without going through the right error paths.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If regulator_get_current_limit() returns 0 or error, return early so the
body of the function doesn't have to be indented as the body of an "if"
statement. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During early days of PCI quirks support, ThunderX firmware did not provide
PNP0c02 node with PCI configuration space and PEM-specific register ranges.
This means that for legacy FW we are not reserving these resources and
cannot gather PEM-specific resources for further PEM initialization.
To support already deployed legacy FW, calculate PEM-specific ranges and
provide resources reservation as fallback scenario into PEM driver when we
could not gather PEM reg base from ACPI tables.
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
"CAV" is the only PNP/ACPI hardware ID vendor prefix assigned to Cavium so
fix this as it should be from day one.
Fixes: 44f22bd91e ("PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller")
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
regulator_get_current_limit() can return negative error codes. We saved
the return value in an unsigned "curr", and a subsequent check interpreted
a negative error code as a positive (invalid) current limit.
Save the return code as a signed value, which avoids messages like this,
seen on Samsung Chromebook Plus:
rockchip-pcie f8000000.pcie: invalid power supply
[bhelgaas: changelog]
Fixes: 4816c4c7b8 ("PCI: rockchip: Provide captured slot power limit and scale")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
2+ PCI devices fail to be discovered due to each bus having the same PCI
domain. This is because the domain defined in the device tree file is not
being added due to PCI_DOMAIN not being enabled. So, every PCI bus has a
domain of zero. When PCI_DOMAIN is selected by the Kconfig, it picks up
the domain defined in the device tree file and everything works as
expected.
Since both PCIE_IPROC_PLATFORM and PCIE_IPROC_BCMA need PCI_DOMAIN, move
it to PCIE_IPROC so it will be automatically selected for both.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since commit fcc392d501 ("irqchip/armada-370-xp: Use the generic MSI
infrastructure"), the irqchip driver used on Armada 370, XP, 375, 38x, 39x
for the MPIC interrupt controller has been converted to use the generic MSI
infrastructure.
Since this commit, it is no longer registering an msi_controller structure
with the of_pci_msi_chip_add() function. Therefore, having the PCI driver
used on the same platform calling of_pci_find_msi_chip_by_node() is pretty
useless.
The MSI resolution is now done in the generic interrupt resolution code,
since the MSI controller is an irq domain attached to the interrupt
controller node, which is pointed to by the msi-parent DT property in the
PCIe controller node.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
The MSI support introduced with the initial Aardvark driver was based
on the msi_controller structure and the of_pci_msi_chip_add() /
of_pci_find_msi_chip_by_node() API, which are being deprecated in
favor of the generic MSI support.
Update the Aardvark driver to use the generic MSI support.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
The host bridge memory window resource is inserted into the iomem_resource
tree and cannot be deallocated until the host bridge itself is removed.
Previously, the window was on the stack, which meant the iomem_resource
entry pointed into the stack and was corrupted as soon as the probe
function returned, which caused memory corruption and errors like this:
pcie_iproc_bcma bcma0:8: resource collision: [mem 0x40000000-0x47ffffff] conflicts with PCIe MEM space [mem 0x40000000-0x47ffffff]
Move the memory window resource from the stack into struct iproc_pcie so
its lifetime matches that of the host bridge.
Fixes: c3245a5664 ("PCI: iproc: Request host bridge window resources")
Reported-and-tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.8+
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hgdy
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix NULL pointer dereferences in many DesignWare-based drivers due to
refactoring error
- fix Altera config write breakage due to my refactoring error
* tag 'pci-v4.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: altera: Fix TLP_CFG_DW0 for TLP write
PCI: dwc: Fix crashes seen due to missing assignments
eb5767122f ("PCI: altera: Simplify TLB_CFG_DW0 usage") used
TLP_FMTTYPE_CFGRD* (instead of TLP_FMTTYPE_CFGWR*) for TLP writes, which
causes writing to configuration space to fail. Fix it by using correct
FMTTYPE for write operation.
Fixes: eb5767122f ("PCI: altera: Simplify TLB_CFG_DW0 usage")
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.9+
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJYo06oAAoJELgmozMOVy/d9Z8QALedWHdu98St1L0u2c8sxnR9
2zo/4sF5Vb9u7FpmdIX32L4SQ9s9KhPE8Qp8NtZLf9v10zlDebIRJDpXknXtKooV
CAXxX4sxBXV27/UrhbZEfXiPrmm6ccJFyIfRnMU6NlMqh2AtAsRa5AC2/RMp8oUD
Med97PFiF0o6TD22/UH1VFbRpX1zjaKyqm7a3as5sJfzNA+UGIZAQ7Euz8000DKZ
xCgVLTEwS0FmOujtBkCst7xa9TjuqR1HLOB4DdGvAhP6BHdz2yamM7Qmh9NN+NEX
0BtjsuXomtn6j6AszGC+bpipCZh3NUigcwoFAARXCYFHibBvo4DPdFeGsraFgXdy
1+KyR8CCeQG3Aly5Vwr264RFPGkGpwMj8PsBlXgQVtrlg4rriaCzOJNmIIbfdADw
ftqhxBOzReZw77aH2s+9p2ILRfcAmPqhynLvFGFo9LBvsik8LVso7YgZN0xGxwcI
IjI/XGC8UskPVsIZBIYA6sl2bYzgOjtBIHiXjRrPlW3uhduIXLrvKFfLPP/5XLAG
ehLXK+J0bfsyY9ClmlNS8oH/WdLhXAyy/KNmnj5bRRm9qg6BRJR3bsOBhZJODuoC
XgEXFfF6/7roNESWxowff7pK0rTkRg/m/Pa4VQpeO+6NWHE7kgZhL6kyIp5nKcwS
3e7mgpcwC+3XfA/6vU3F
=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4Owc
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
* pci/host-rockchip:
PCI: rockchip: Set vendor ID from local core config space
PCI: rockchip: Fix rockchip_pcie_probe() error path to free resource list
PCI: rockchip: Mark PM functions as __maybe_unused
PCI: rockchip: Use readl_poll_timeout() instead of open-coding it
PCI: rockchip: Disable RC's ASPM L0s based on DT "aspm-no-l0s"
PCI: rockchip: Add system PM support
* pci/host-rcar:
PCI: rcar: Use of_device_get_match_data() to simplify probe
PCI: rcar: Add compatible string for r8a7796
PCI: rcar: Return -ENODEV from host bridge probe when no card present
* pci/host-hisi:
PCI: generic: Call pci_fixup_irqs() only on ARM
PCI: Disable MSI for HiSilicon Hip06/Hip07 Root Ports
PCI: hisi: Rename config space accessors to remove "acpi"
PCI: hisi: Add DT almost-ECAM support for Hip06/Hip07 host controllers
PCI: hisi: Use of_device_get_match_data() to simplify probe
Conflicts:
drivers/pci/dwc/pcie-hisi.c
Group all the PCI drivers that use DesignWare core in dwc directory.
dwc IP is capable of operating in both host mode and device mode and
keeping it inside the *host* directory is misleading.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Minghuan Lian <minghuan.Lian@freescale.com>
Cc: Mingkai Hu <mingkai.hu@freescale.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Previously we extracted 'Completion Status' from b14:12, but it is actually
b15:13. Extract it from the correct bits.
Signed-off-by: Hu Yadi<yadi.hu@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
The TRM says the vendor ID in the RC's configure space can be rewritten
and the value must be the same as the value read from the local core
configure space. But we misread that and didn't notice it before. Actually
we should only able to rewrite it from the local core configure space.
Fix that issue to make lspci show the correct IP vendor infomation.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the device serial number as the PCI domain. The serial numbers start
with 1 and are unique within a VM. So names, such as VF NIC names, that
include domain number as part of the name, can be shorter than that based
on part of bus UUID previously. The new names will also stay same for VMs
created with copied VHD and same number of devices.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
rockchip_pcie_probe() calls of_pci_get_host_bridge_resources() to parse
resources from DT and build a resource list. The caller is responsible for
disposing of the resource list. This is normally done by
pci_release_host_bridge_dev() when the host bridge is removed.
If the host bridge probe fails, dispose of the resource list in the probe
error path.
[bhelgaas: changelog]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The devfn of 00:02.0 is 0x10. devfn_to_wslot(0x10) == 0x2, and
wslot_to_devfn(0x2) should be 0x10, while it's 0x2 in the current code.
Due to this, hv_eject_device_work() -> pci_get_domain_bus_and_slot()
returns NULL and pci_stop_and_remove_bus_device() is not called.
Later when the real device driver's .remove() is invoked by
hv_pci_remove() -> pci_stop_root_bus(), some warnings can be noticed
because the VM has lost the access to the underlying device at that
time.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
CC: stable@vger.kernel.org
CC: K. Y. Srinivasan <kys@microsoft.com>
CC: Stephen Hemminger <sthemmin@microsoft.com>
Remove support for vendor-defined messages which are not supported by AXI.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make sure PCIe MPS settings are valid when we enumerate a new hierarchy.
Based-on-patch-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_fixup_irqs() is problematic because:
- it's called when we enumerate a host bridge, so we don't fixup IRQs for
hot-added PCI devices, and
- it fixes up IRQs for all PCI devices in the system, so if we call it
multiple times, e.g., if we have several host controllers, we may
reallocate an IRQ for a device after a driver has already claimed it.
We plan to replace pci_fixup_irqs() soon, but we still need it on ARM
because we don't have any other generic method for doing this.
On ARM64, we don't need pci_fixup_irqs() because we do IRQ setup when we
bind a driver to the device (in the pci_device_probe() ->
pcibios_alloc_irq() path).
pci-host-common.c is currently only used on ARM and ARM64. In principle,
it could be used on x86, and we wouldn't want pci_fixup_irqs() there
either, because x86 does IRQ setup in the pci_enable_device() path.
[bhelgaas: changelog, use #ifdef ARM, not #ifndef ARM64]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There's nothing ACPI-specific about the config space accessors
hisi_pcie_acpi_rd_conf() and hisi_pcie_acpi_wr_conf(), and they're used for
both the ACPI and the DT driver model.
Rename them to hisi_pcie_rd_conf() and hisi_pcie_wr_conf(). No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make sure PCIe MPS settings are valid when we enumerate a new hierarchy.
Based-on-patch-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make sure PCIe MPS settings are valid when we enumerate a new hierarchy.
Based-on-patch-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make sure PCIe MPS settings are valid when we enumerate a new hierarchy.
[bhelgaas: changelog]
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
The current default of 20ms cause some devices, which are slow to
initialize, to not show up during the bus scanning. Change this to the
PCIe spec mandated 100ms and document this in the DT binding.
From PCIe base spec rev 3.0, chapter "6.6.1. Conventional Reset":
To allow components to perform internal initialization, system software
must wait a specified minimum period following the end of a Conventional
Reset of one or more devices before it is permitted to issue
Configuration Requests to those devices.
With a Downstream Port that does not support Link speeds greater than 5.0
GT/s, software must wait a minimum of 100 ms before sending a
Configuration Request to the device immediately below that Port.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
The PCIe controller in HiSilicon Hip06/Hip07 SoCs is not completely
ECAM-compliant. It is non-ECAM only for the RC bus config space; for any
other bus underneath the root bus it does support ECAM access.
Add DT support for the almost-ECAM Hip06/Hip07 controllers.
[bhelgaas: drop dev->of_node test, driver name "hisi-pcie-almost-ecam"]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
The only way to call hisi_pcie_probe() is to match an entry in
hisi_pcie_of_match[], so match cannot be NULL.
Use of_device_get_match_data() to retrieve the soc_ops pointer. No
functional change intended.
[bhelgaas: use of_device_get_match_data(), changelog]
Based-on-suggestion-from: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The only way to call iproc_pcie_pltfm_probe() is to match an entry in
iproc_pcie_of_match_table[], so match cannot be NULL.
Use of_device_get_match_data() to retrieve the pcie->type. No functional
change intended.
Based-on-suggestion-from: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is a DT-only driver, so the only way to call rcar_pcie_probe() is to
match an entry in rcar_pcie_of_match[], so of_id cannot be NULL.
Furthermore, of_id->data can only be NULL if an rcar_pcie_of_match[] entry
has a NULL .data member. That's a driver defect, and we don't want to
return -EINVAL, which is easy to ignore. We'd rather take the NULL pointer
dereference so we notice the problem and fix it.
Use of_device_get_match_data() to retrieve the hw_init_fn pointer. No
functional change intended.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The "port" variable was allocated with devm_kzalloc() so if we free it with
kfree() it will be freed twice. Also I changed it to propogate the error
from devm_ioremap_resource() instead of returning -ENOMEM.
Fixes: c5d4603961 ("PCI: Add MCFG quirks for X-Gene host controller")
Also-posted-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
When CONFIG_PM_SLEEP is disabled, we get harmless build warnings:
host/pcie-rockchip.c:1267:12: error: 'rockchip_pcie_resume_noirq' defined but not used [-Werror=unused-function]
host/pcie-rockchip.c:1240:12: error: 'rockchip_pcie_suspend_noirq' defined but not used [-Werror=unused-function]
Marking both functions as __maybe_unused avoids the warning without the
need for #ifdef around them.
Fixes: 013dd3d5e1 ("PCI: rockchip: Add system PM support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Use readl_poll_timeout() instead of open-coding it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core will write to the bridge window config multiple times while
they are enabled. This can lead to mbus failures like this:
mvebu_mbus: cannot add window '4:e8', conflicts with another window
mvebu-pcie mbus:pex@e0000000: Could not create MBus window at [mem 0xe0000000-0xe00fffff]: -22
For me this is happening during a hotplug cycle. The PCI core is not
changing the values, just writing them twice while active.
The patch addresses the general case of any change to an active window, but
not atomically. The code is slightly refactored so io and mem can share
more of the window logic.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
The conversion to the new hotplug state machine introduced a regression
where a successful hotplug registration would be treated as an error,
effectively disabling the MSI driver forever.
Fix it by doing the proper check on the return value.
Fixes: 9c248f8896 ("PCI/xgene-msi: Convert to hotplug state machine")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Duc Dang <dhdang@apm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: stable@vger.kernel.org
The pci-thunder-pem driver was initially developed for cn88xx SoCs. The
cn81xx and cn83xx members of the same family of SoCs have a slightly
different configuration of interrupt resources in the PEM hardware, which
prevents the INTA legacy interrupt source from functioning with the current
driver.
There are two fixes required:
1) Don't fixup the PME interrupt on the newer SoCs as it already has the
proper value.
2) Report MSI-X Capability Table Size of 2 for the newer SoCs, so the core
MSI-X code doesn't inadvertently clobber the INTA machinery that happens to
reside immediately following the table.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rockchip's RC produces a 100MHz reference clock but there are two methods
for the PHY to generate it:
(1) Use the system PLL to generate a 100MHz clock. The PHY will relock
it, filter signal noise, and output the reference clock. ASPM L0s
works correctly, but circuit noise issues make it difficult to pass
the TX compatibility test.
(2) Share the SoC's 24MHZ crystal oscillator with the PHY and force the
PHY's PLL to generate 100MHz internally. In this case, exit from
ASPM L0s sometimes fails due to a design error in the RC receiver
circuit. Even if we use extended-synch, the PHY sometimes fails to
relock the bits from FTS, which will hang the system.
We want the flexibility to use both clocking methods, so add a DT property,
"aspm-no-l0s". If that's present, disable L0s to avoid the issues with
case (2).
[bhelgaas: changelog]
Reported-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
R-Car PCIe does not support hotplug so it is appropriate to treat the
absence of a PCIe card as an -ENODEV error.
Signed-off-by: Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>
[simon: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add system PM support for Rockchip's RC. For pre S3, the EP is configured
into D3 state which guarantees the link state should be in L1. So we could
send PME_Turn_Off message to the EP and wait for its ACK to make the link
state into L2 or L3 without the aux-supply. This could help save more
power which I think should be very important for mobile devices.
As note that there is a 5s timeout for RC to wait for the PMA_ACK after
sending PME_Turn_Off. Technically it should depend on the hierarchy of
devices but seems PCIe core framework doesn't handle the L2/3 for S3 at
all. So that means we should presume to set a default value for PME_ACK.
From the bug report[1], we could find a statement that Microsoft Windows
versions typically wait for 5 seconds. So we are prone to take 5s for this
timeout here.
[1] https://lists.launchpad.net/kernel-packages/msg123315.html
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Previously we checked for iATU unroll support by reading PCIE_ATU_VIEWPORT
even on platforms, e.g., Keystone, that do not have ATU ports. This can
cause bad behavior such as asynchronous external aborts:
OF: PCI: MEM 0x60000000..0x6fffffff -> 0x60000000
Unhandled fault: asynchronous external abort (0x1211) at 0x00000000
pgd = c0003000
[00000000] *pgd=80000800004003, *pmd=00000000
Internal error: : 1211 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-00009-g6ff59d2-dirty #7
Hardware name: Keystone
task: eb878000 task.stack: eb866000
PC is at dw_pcie_setup_rc+0x24/0x380
LR is at ks_pcie_host_init+0x10/0x170
Move the dw_pcie_iatu_unroll_enabled() check so we only call it on
platforms that do not use the ATU. These platforms supply their own
->rd_other_conf() and ->wr_other_conf() methods.
[bhelgaas: changelog]
Fixes: a0601a4705 ("PCI: designware: Add iATU Unroll feature")
Fixes: 416379f9eb ("PCI: designware: Check for iATU unroll support after initializing host")
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
CC: stable@vger.kernel.org # v4.9+
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
* pci/host-vmd:
PCI: vmd: Fix suspend handlers defined-but-not-used warning
PCI: vmd: Use SRCU as a local RCU to prevent delaying global RCU
PCI: vmd: Remove unnecessary pci_set_drvdata()
* pci/host-rockchip:
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
PCI: rockchip: Split out rockchip_cfg_atu()
PCI: rockchip: Clean up bit definitions for PCIE_RC_CONFIG_LCS
PCI: rockchip: Correct the use of FTS mask
PCI: rockchip: Remove the pointer to L1 substate cap
PCI: rockchip: Specify the link capability
PCI: rockchip: Fix negotiated lanes calculation
PCI: rockchip: Add Kconfig COMPILE_TEST
PCI: rockchip: Mark RC as common clock architecture
PCI: rockchip: Provide captured slot power limit and scale
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
PCI: designware: Check for iATU unroll support after initializing host
PCI: qcom: Fix pp->dev usage before assignment
PCI: designware-plat: Update author email address
PCI: layerscape: Fix drvdata usage before assignment
PCI: designware-plat: Change maintainer to Jose Abreu
