Split the query of HW-attached program from the software one.
Introduce new .ndo_bpf command to query HW-attached program.
This will allow drivers to install different programs in HW
and SW at the same time. Netlink can now also carry multiple
programs on dump (in which case mode will be set to
XDP_ATTACHED_MULTI and user has to check per-attachment point
attributes, IFLA_XDP_PROG_ID will not be present). We reuse
IFLA_XDP_PROG_ID skb space for second mode, so rtnl_xdp_size()
doesn't need to be updated.
Note that the installation side is still not there, since all
drivers currently reject installing more than one program at
the time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Basic operations drivers perform during xdp setup and query can
be moved to helpers in the core. Encapsulate program and flags
into a structure and add helpers. Note that the structure is
intended as the "main" program information source in the driver.
Most drivers will additionally place the program pointer in their
fast path or ring structures.
The helpers don't have a huge impact now, but they will
decrease the code duplication when programs can be installed
in HW and driver at the same time. Encapsulating the basic
operations in helpers will hopefully also reduce the number
of changes to drivers which adopt them.
Helpers could really be static inline, but they depend on
definition of struct netdev_bpf which means they'd have
to be placed in netdevice.h, an already 4500 line header.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
prog_attached of struct netdev_bpf should have been superseded
by simply setting prog_id long time ago, but we kept it around
to allow offloading drivers to communicate attachment mode (drv
vs hw). Subsequently drivers were also allowed to report back
attachment flags (prog_flags), and since nowadays only programs
attached will XDP_FLAGS_HW_MODE can get offloaded, we can tell
the attachment mode from the flags driver reports. Remove
prog_attached member.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In preparation for support of simultaneous driver and hardware XDP
support add per-mode attributes. The catch-all IFLA_XDP_PROG_ID
will still be reported, but user space can now also access the
program ID in a new IFLA_XDP_<mode>_PROG_ID attribute.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
region_snapshot - When set enables capturing region snapshots
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DEVLINK_CMD_REGION_READ_GET used for both reading
and dumping region data. Read allows reading from a region specific
address for given length. Dump allows reading the full region.
If only snapshot ID is provided a snapshot dump will be done.
If snapshot ID, Address and Length are provided a snapshot read
will done.
This is used for both snapshot access and will be used in the same
way to access current data on the region.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DEVLINK_CMD_REGION_DEL used
for deleting a snapshot from a region. The snapshot ID is required.
Also added notification support for NEW and DEL of snapshots.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the support for DEVLINK_CMD_REGION_GET command to also
return the IDs of the snapshot currently present on the region.
Each reply will include a nested snapshots attribute that
can contain multiple snapshot attributes each with an ID.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DEVLINK_CMD_REGION_GET command which is used for
querying for the supported DEV/REGION values of devlink devices.
The support is both for doit and dumpit.
Reply includes:
BUS_NAME, DEVICE_NAME, REGION_NAME, REGION_SIZE
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each device address region can store multiple snapshots,
each snapshot is identified using a different numerical ID.
This ID is used when deleting a snapshot or showing an address
region specific snapshot. This patch exposes a callback to add
a new snapshot to an address region.
The snapshot will be deleted using the destructor function
when destroying a region or when a snapshot delete command
from devlink user tool.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To restrict the driver with the snapshot ID selection a new callback
is introduced for the driver to get the snapshot ID before creating
a new snapshot. This will also allow giving the same ID for multiple
snapshots taken of different regions on the same time.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a device to register its supported address regions.
Each address region can be accessed directly for example reading
the snapshots taken of this address space.
Drivers are not limited in the name selection for different regions.
An example of a region-name can be: pci cr-space, register-space.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pfmemalloc flag indicates that the skb was allocated from
the PFMEMALLOC reserves, and the flag is currently copied on skb
copy and clone.
However, an skb copied from an skb flagged with pfmemalloc
wasn't necessarily allocated from PFMEMALLOC reserves, and on
the other hand an skb allocated that way might be copied from an
skb that wasn't.
So we should not copy the flag on skb copy, and rather decide
whether to allow an skb to be associated with sockets unrelated
to page reclaim depending only on how it was allocated.
Move the pfmemalloc flag before headers_start[0] using an
existing 1-bit hole, so that __copy_skb_header() doesn't copy
it.
When cloning, we'll now take care of this flag explicitly,
contravening to the warning comment of __skb_clone().
While at it, restore the newline usage introduced by commit
b193722731 ("net: reorganize sk_buff for faster
__copy_skb_header()") to visually separate bytes used in
bitfields after headers_start[0], that was gone after commit
a9e419dc7b ("netfilter: merge ctinfo into nfct pointer storage
area"), and describe the pfmemalloc flag in the kernel-doc
structure comment.
This doesn't change the size of sk_buff or cacheline boundaries,
but consolidates the 15 bits hole before tc_index into a 2 bytes
hole before csum, that could now be filled more easily.
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Fixes: c93bdd0e03 ("netvm: allow skb allocation to use PFMEMALLOC reserves")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
L2 Fwd Offload & 10GbE Intel Driver Updates 2018-07-09
This patch series is meant to allow support for the L2 forward offload, aka
MACVLAN offload without the need for using ndo_select_queue.
The existing solution currently requires that we use ndo_select_queue in
the transmit path if we want to associate specific Tx queues with a given
MACVLAN interface. In order to get away from this we need to repurpose the
tc_to_txq array and XPS pointer for the MACVLAN interface and use those as
a means of accessing the queues on the lower device. As a result we cannot
offload a device that is configured as multiqueue, however it doesn't
really make sense to configure a macvlan interfaced as being multiqueue
anyway since it doesn't really have a qdisc of its own in the first place.
The big changes in this set are:
Allow lower device to update tc_to_txq and XPS map of offloaded MACVLAN
Disable XPS for single queue devices
Replace accel_priv with sb_dev in ndo_select_queue
Add sb_dev parameter to fallback function for ndo_select_queue
Consolidated ndo_select_queue functions that appeared to be duplicates
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_lwt_seg6_* helpers require CONFIG_IPV6_SEG6_BPF, and currently
return -EOPNOTSUPP to indicate unavailability. This patch forces the
BPF verifier to reject programs using these helpers when
!CONFIG_IPV6_SEG6_BPF, allowing users to more easily probe if they are
available or not.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Mark reported that syzkaller triggered a KASAN detected slab-out-of-bounds
bug in ___bpf_prog_run() with a BPF_LD | BPF_ABS word load at offset 0x8001.
After further investigation it became clear that the issue was the
BPF_LDX_MEM() which takes offset as an argument whereas it cannot encode
larger than S16_MAX offsets into it. For this synthetical case we need to
move the full address into tmp register instead and do the LDX without
immediate value.
Fixes: e0cea7ce98 ("bpf: implement ld_abs/ld_ind in native bpf")
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
__netif_receive_skb_core can free the skb, so we have to use the dequeue-
enqueue model when calling it from __netif_receive_skb_list_core.
Fixes: 88eb1944e1 ("net: core: propagate SKB lists through packet_type lookup")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netif_receive_skb_list_internal(), all of skb_defer_rx_timestamp(),
do_xdp_generic() and enqueue_to_backlog() can lead to kfree(skb). Thus,
we cannot wait until after they return to remove the skb from the list;
instead, we remove it first and, in the pass case, add it to a sublist
afterwards.
In the case of enqueue_to_backlog() we have already decided not to pass
when we call the function, so we do not need a sublist.
Fixes: 7da517a3bc ("net: core: Another step of skb receive list processing")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most of these calls we can just pass NULL through to the fallback
function as the sb_dev. The only cases where we cannot are the cases where
we might be dealing with either an upper device or a driver that would
have configured things to support an sb_dev itself.
The only driver that has any significant change in this patch set should be
ixgbe as we can drop the redundant functionality that existed in both the
ndo_select_queue function and the fallback function that was passed through
to us.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that instead of passing a void pointer as the
accel_priv we instead pass a net_device pointer as sb_dev. Making this
change allows us to pass the subordinate device through to the fallback
function eventually so that we can keep the actual code in the
ndo_select_queue call as focused on possible on the exception cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a generic version of the ndo_select_queue functions for
either returning 0 or selecting a queue based on the processor ID. This is
generally meant to just reduce the number of functions we have to change
in the future when we have to deal with ndo_select_queue changes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can support the concept of subordinate
device traffic classes to the core networking code. In doing this we can
start pulling out the driver specific bits needed to support selecting a
queue based on an upper device.
The solution at is currently stands is only partially implemented. I have
the start of some XPS bits in here, but I would still need to allow for
configuration of the XPS maps on the queues reserved for the subordinate
devices. For now I am using the reference to the sb_dev XPS map as just a
way to skip the lookup of the lower device XPS map for now as that would
result in the wrong queue being picked.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to provide the basic tools needed to allow us to create
subordinate device traffic classes. The general idea here is to allow
subdividing the queues of a device into queue groups accessible through an
upper device such as a macvlan.
The idea here is to enforce the idea that an upper device has to be a
single queue device, ideally with IFF_NO_QUQUE set. With that being the
case we can pretty much guarantee that the tc_to_txq mappings and XPS maps
for the upper device are unused. As such we could reuse those in order to
support subdividing the lower device and distributing those queues between
the subordinate devices.
In order to distinguish between a regular set of traffic classes and if a
device is carrying subordinate traffic classes I changed num_tc from a u8
to a s16 value and use the negative values to represent the subordinate
pool values. So starting at -1 and running to -32768 we can encode those as
pool values, and the existing values of 0 to 15 can be maintained.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that we do not report the traffic class or allow XPS
configuration on single queue devices. This is mostly to avoid unnecessary
complexity with changes I have planned that will allow us to reuse
the unused tc_to_txq and XPS configuration on a single queue device to
allow it to make use of a subset of queues on an underlying device.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf 2018-07-07
The following pull-request contains BPF updates for your *net* tree.
Plenty of fixes for different components:
1) A set of critical fixes for sockmap and sockhash, from John Fastabend.
2) fixes for several race conditions in af_xdp, from Magnus Karlsson.
3) hash map refcnt fix, from Mauricio Vasquez.
4) samples/bpf fixes, from Taeung Song.
5) ifup+mtu check for xdp_redirect, from Toshiaki Makita.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we end up with attempting to send packets from down devices
or to send oversized packets, which may cause unexpected driver/device
behaviour. Generic XDP has already done this check, so reuse the logic
in native XDP.
Fixes: 814abfabef ("xdp: add bpf_redirect helper function")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In commit
'bpf: bpf_compute_data uses incorrect cb structure' (8108a77515)
we added the routine bpf_compute_data_end_sk_skb() to compute the
correct data_end values, but this has since been lost. In kernel
v4.14 this was correct and the above patch was applied in it
entirety. Then when v4.14 was merged into v4.15-rc1 net-next tree
we lost the piece that renamed bpf_compute_data_pointers to the
new function bpf_compute_data_end_sk_skb. This was done here,
e1ea2f9856 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
When it conflicted with the following rename patch,
6aaae2b6c4 ("bpf: rename bpf_compute_data_end into bpf_compute_data_pointers")
Finally, after a refactor I thought even the function
bpf_compute_data_end_sk_skb() was no longer needed and it was
erroneously removed.
However, we never reverted the sk_skb_convert_ctx_access() usage of
tcp_skb_cb which had been committed and survived the merge conflict.
Here we fix this by adding back the helper and *_data_end_sk_skb()
usage. Using the bpf_skc_data_end mapping is not correct because it
expects a qdisc_skb_cb object but at the sock layer this is not the
case. Even though it happens to work here because we don't overwrite
any data in-use at the socket layer and the cb structure is cleared
later this has potential to create some subtle issues. But, even
more concretely the filter.c access check uses tcp_skb_cb.
And by some act of chance though,
struct bpf_skb_data_end {
struct qdisc_skb_cb qdisc_cb; /* 0 28 */
/* XXX 4 bytes hole, try to pack */
void * data_meta; /* 32 8 */
void * data_end; /* 40 8 */
/* size: 48, cachelines: 1, members: 3 */
/* sum members: 44, holes: 1, sum holes: 4 */
/* last cacheline: 48 bytes */
};
and then tcp_skb_cb,
struct tcp_skb_cb {
[...]
struct {
__u32 flags; /* 24 4 */
struct sock * sk_redir; /* 32 8 */
void * data_end; /* 40 8 */
} bpf; /* 24 */
};
So when we use offset_of() to track down the byte offset we get 40 in
either case and everything continues to work. Fix this mess and use
correct structures its unclear how long this might actually work for
until someone moves the structs around.
Reported-by: Martin KaFai Lau <kafai@fb.com>
Fixes: e1ea2f9856 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Fixes: 6aaae2b6c4 ("bpf: rename bpf_compute_data_end into bpf_compute_data_pointers")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Multiple BPF helpers in use by sk_skb programs calculate the max
skb length using the __bpf_skb_max_len function. However, this
calculates the max length using the skb->dev pointer which can be
NULL when an sk_skb program is paired with an sk_msg program.
To force this a sk_msg program needs to redirect into the ingress
path of a sock with an attach sk_skb program. Then the the sk_skb
program would need to call one of the helpers that adjust the skb
size.
To fix the null ptr dereference use SKB_MAX_ALLOC size if no dev
is available.
Fixes: 8934ce2fd0 ("bpf: sockmap redirect ingress support")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Dissect the QinQ packets to get both outer and inner vlan information,
then store to the extended flow keys.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change vlan dissector key to save vlan tpid to support both 802.1Q
and 802.1AD ethertype.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_configure_link sets dev->rtnl_link_state to
RTNL_LINK_INITIALIZED and unconditionally calls
__dev_notify_flags to notify user-space of dev flags.
current call sequence for rtnl_configure_link
rtnetlink_newlink
rtnl_link_ops->newlink
rtnl_configure_link (unconditionally notifies userspace of
default and new dev flags)
If a newlink handler wants to call rtnl_configure_link
early, we will end up with duplicate notifications to
user-space.
This patch fixes rtnl_configure_link to check rtnl_link_state
and call __dev_notify_flags with gchanges = 0 if already
RTNL_LINK_INITIALIZED.
Later in the series, this patch will help the following sequence
where a driver implementing newlink can call rtnl_configure_link
to initialize the link early.
makes the following call sequence work:
rtnetlink_newlink
rtnl_link_ops->newlink (vxlan) -> rtnl_configure_link (initializes
link and notifies
user-space of default
dev flags)
rtnl_configure_link (updates dev flags if requested by user ifm
and notifies user-space of new dev flags)
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV)
characteristic of the device.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 2 first generic parameters to devlink configuration parameters set:
internal_err_reset - When set enables reset device on internal errors.
max_macs - max number of MACs per ETH port.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink_param_notify() function to support devlink param notifications.
Add notification call to devlink param set, register and unregister
functions.
Add devlink_param_value_changed() function to enable the driver notify
devlink on value change. Driver should use this function after value was
changed on any configuration mode part to driverinit.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"driverinit" configuration mode value is held by devlink to enable
the driver query the value after reload. Two additional functions
added to help the driver get/set the value from/to devlink:
devlink_param_driverinit_value_set() and
devlink_param_driverinit_value_get().
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add param set command to set value for a parameter.
Value can be set to any of the supported configuration modes.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add param get command which gets data per parameter.
Option to dump the parameters data per device.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define configuration parameters data structure.
Add functions to register and unregister the driver supported
configuration parameters table.
For each parameter registered, the driver should fill all the parameter's
fields. In case the only supported configuration mode is "driverinit"
the parameter's get()/set() functions are not required and should be set
to NULL, for any other configuration mode, these functions are required
and should be set by the driver.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 07d78363dc ("net: Convert NAPI gro list into a small hash
table.")' there is 8 hash buckets, which allows more flows to be held for
merging. but MAX_GRO_SKBS, the total held skb for merging, is 8 skb still,
limit the hash table performance.
keep MAX_GRO_SKBS as 8 skb, but limit each hash list length to 8 skb, not
the total 8 skb
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the socket error queue for reporting dropped packets if the
socket has enabled that feature through the SO_TXTIME API.
Packets are dropped either on enqueue() if they aren't accepted by the
qdisc or on dequeue() if the system misses their deadline. Those are
reported as different errors so applications can react accordingly.
Userspace can retrieve the errors through the socket error queue and the
corresponding cmsg interfaces. A struct sock_extended_err* is used for
returning the error data, and the packet's timestamp can be retrieved by
adding both ee_data and ee_info fields as e.g.:
((__u64) serr->ee_data << 32) + serr->ee_info
This feature is disabled by default and must be explicitly enabled by
applications. Enabling it can bring some overhead for the Tx cycles
of the application.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces SO_TXTIME. User space enables this option in
order to pass a desired future transmit time in a CMSG when calling
sendmsg(2). The argument to this socket option is a 8-bytes long struct
provided by the uapi header net_tstamp.h defined as:
struct sock_txtime {
clockid_t clockid;
u32 flags;
};
Note that new fields were added to struct sock by filling a 2-bytes
hole found in the struct. For that reason, neither the struct size or
number of cachelines were altered.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done in preparation for the upcoming time based transmission
patchset. Now that skb->tstamp will be used to hold packet's txtime,
we must ensure that it is being cleared when traversing namespaces.
Also, doing that from skb_scrub_packet() before the early return would
break our feature when tunnels are used.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.
However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.
Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.
Tested-by: Pete Heist <pete@heistp.net>
Tested-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally the check should be very cheap, as the sk_buff_head is in cache.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also involved adding a way to run a netfilter hook over a list of packets.
Rather than attempting to make netfilter know about lists (which would be
a major project in itself) we just let it call the regular okfn (in this
case ip_rcv_finish()) for any packets it steals, and have it give us back
a list of packets it's synchronously accepted (which normally NF_HOOK
would automatically call okfn() on, but we want to be able to potentially
pass the list to a listified version of okfn().)
The netfilter hooks themselves are indirect calls that still happen per-
packet (see nf_hook_entry_hookfn()), but again, changing that can be left
for future work.
There is potential for out-of-order receives if the netfilter hook ends up
synchronously stealing packets, as they will be processed before any
accepts earlier in the list. However, it was already possible for an
asynchronous accept to cause out-of-order receives, so presumably this is
considered OK.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__netif_receive_skb_core() does a depressingly large amount of per-packet
work that can't easily be listified, because the another_round looping
makes it nontrivial to slice up into smaller functions.
Fortunately, most of that work disappears in the fast path:
* Hardware devices generally don't have an rx_handler
* Unless you're tcpdumping or something, there is usually only one ptype
* VLAN processing comes before the protocol ptype lookup, so doesn't force
a pt_prev deliver
so normally, __netif_receive_skb_core() will run straight through and pass
back the one ptype found in ptype_base[hash of skb->protocol].
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First example of a layer splitting the list (rather than merely taking
individual packets off it).
Involves new list.h function, list_cut_before(), like list_cut_position()
but cuts on the other side of the given entry.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_receive_skb_list_internal() now processes a list and hands it
on to the next function.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Verify netlink attributes properly in nf_queue, from Eric Dumazet.
2) Need to bump memory lock rlimit for test_sockmap bpf test, from
Yonghong Song.
3) Fix VLAN handling in lan78xx driver, from Dave Stevenson.
4) Fix uninitialized read in nf_log, from Jann Horn.
5) Fix raw command length parsing in mlx5, from Alex Vesker.
6) Cleanup loopback RDS connections upon netns deletion, from Sowmini
Varadhan.
7) Fix regressions in FIB rule matching during create, from Jason A.
Donenfeld and Roopa Prabhu.
8) Fix mpls ether type detection in nfp, from Pieter Jansen van Vuuren.
9) More bpfilter build fixes/adjustments from Masahiro Yamada.
10) Fix XDP_{TX,REDIRECT} flushing in various drivers, from Jesper
Dangaard Brouer.
11) fib_tests.sh file permissions were broken, from Shuah Khan.
12) Make sure BH/preemption is disabled in data path of mac80211, from
Denis Kenzior.
13) Don't ignore nla_parse_nested() return values in nl80211, from
Johannes berg.
14) Properly account sock objects ot kmemcg, from Shakeel Butt.
15) Adjustments to setting bpf program permissions to read-only, from
Daniel Borkmann.
16) TCP Fast Open key endianness was broken, it always took on the host
endiannness. Whoops. Explicitly make it little endian. From Yuching
Cheng.
17) Fix prefix route setting for link local addresses in ipv6, from
David Ahern.
18) Potential Spectre v1 in zatm driver, from Gustavo A. R. Silva.
19) Various bpf sockmap fixes, from John Fastabend.
20) Use after free for GRO with ESP, from Sabrina Dubroca.
21) Passing bogus flags to crypto_alloc_shash() in ipv6 SR code, from
Eric Biggers.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
qede: Adverstise software timestamp caps when PHC is not available.
qed: Fix use of incorrect size in memcpy call.
qed: Fix setting of incorrect eswitch mode.
qed: Limit msix vectors in kdump kernel to the minimum required count.
ipvlan: call dev_change_flags when ipvlan mode is reset
ipv6: sr: fix passing wrong flags to crypto_alloc_shash()
net: fix use-after-free in GRO with ESP
tcp: prevent bogus FRTO undos with non-SACK flows
bpf: sockhash, add release routine
bpf: sockhash fix omitted bucket lock in sock_close
bpf: sockmap, fix smap_list_map_remove when psock is in many maps
bpf: sockmap, fix crash when ipv6 sock is added
net: fib_rules: bring back rule_exists to match rule during add
hv_netvsc: split sub-channel setup into async and sync
net: use dev_change_tx_queue_len() for SIOCSIFTXQLEN
atm: zatm: Fix potential Spectre v1
s390/qeth: consistently re-enable device features
s390/qeth: don't clobber buffer on async TX completion
s390/qeth: avoid using is_multicast_ether_addr_64bits on (u8 *)[6]
s390/qeth: fix race when setting MAC address
...
Currently trace_sock_exceed_buf_limit() only show rmem info,
but wmem limit may also be hit.
So expose wmem info in this tracepoint as well.
Regarding memcg, I think it is better to introduce a new tracepoint(if
that is needed), i.e. trace_memcg_limit_hit other than show memcg info in
trace_sock_exceed_buf_limit.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend transmit queue sysfs attribute to configure Rx queue(s) map
per Tx queue. By default no receive queues are configured for the
Tx queue.
- /sys/class/net/eth0/queues/tx-*/xps_rxqs
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to pick Tx queue based on the Rx queue(s) map
configuration set by the admin through the sysfs attribute
for each Tx queue. If the user configuration for receive queue(s) map
does not apply, then the Tx queue selection falls back to CPU(s) map
based selection and finally to hashing.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new field to sock_common 'skc_rx_queue_mapping'
which holds the receive queue number for the connection. The Rx queue
is marked in tcp_finish_connect() to allow a client app to do
SO_INCOMING_NAPI_ID after a connect() call to get the right queue
association for a socket. Rx queue is also marked in tcp_conn_request()
to allow syn-ack to go on the right tx-queue associated with
the queue on which syn is received.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use static_key for XPS maps to reduce the cost of extra map checks,
similar to how it is used for RPS and RFS. This includes static_key
'xps_needed' for XPS and another for 'xps_rxqs_needed' for XPS using
Rx queues map.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor XPS code to support Tx queue selection based on
CPU(s) map or Rx queue(s) map.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-07-01
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) A bpf_fib_lookup() helper fix to change the API before freeze to
return an encoding of the FIB lookup result and return the nexthop
device index in the params struct (instead of device index as return
code that we had before), from David.
2) Various BPF JIT fixes to address syzkaller fallout, that is, do not
reject progs when set_memory_*() fails since it could still be RO.
Also arm32 JIT was not using bpf_jit_binary_lock_ro() API which was
an issue, and a memory leak in s390 JIT found during review, from
Daniel.
3) Multiple fixes for sockmap/hash to address most of the syzkaller
triggered bugs. Usage with IPv6 was crashing, a GPF in bpf_tcp_close(),
a missing sock_map_release() routine to hook up to callbacks, and a
fix for an omitted bucket lock in sock_close(), from John.
4) Two bpftool fixes to remove duplicated error message on program load,
and another one to close the libbpf object after program load. One
additional fix for nfp driver's BPF offload to avoid stopping offload
completely if replace of program failed, from Jakub.
5) Couple of BPF selftest fixes that bail out in some of the test
scripts if the user does not have the right privileges, from Jeffrin.
6) Fixes in test_bpf for s390 when CONFIG_BPF_JIT_ALWAYS_ON is set
where we need to set the flag that some of the test cases are expected
to fail, from Kleber.
7) Fix to detangle BPF_LIRC_MODE2 dependency from CONFIG_CGROUP_BPF
since it has no relation to it and lirc2 users often have configs
without cgroups enabled and thus would not be able to use it, from Sean.
8) Fix a selftest failure in sockmap by removing a useless setrlimit()
call that would set a too low limit where at the same time we are
already including bpf_rlimit.h that does the job, from Yonghong.
9) Fix BPF selftest config with missing missing NET_SCHED, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit f9d4b0c1e9 ("fib_rules: move common handling of newrule
delrule msgs into fib_nl2rule"), rule_exists got replaced by rule_find
for existing rule lookup in both the add and del paths. While this
is good for the delete path, it solves a few problems but opens up
a few invalid key matches in the add path.
$ip -4 rule add table main tos 10 fwmark 1
$ip -4 rule add table main tos 10
RTNETLINK answers: File exists
The problem here is rule_find does not check if the key masks in
the new and old rule are the same and hence ends up matching a more
secific rule. Rule key masks cannot be easily compared today without
an elaborate if-else block. Its best to introduce key masks for easier
and accurate rule comparison in the future. Until then, due to fear of
regressions this patch re-introduces older loose rule_exists during add.
Also fixes both rule_exists and rule_find to cover missing attributes.
Fixes: f9d4b0c1e9 ("fib_rules: move common handling of newrule delrule msgs into fib_nl2rule")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Eric, we need to switch to the helper
dev_change_tx_queue_len() for SIOCSIFTXQLEN call path too,
otheriwse still miss dev_qdisc_change_tx_queue_len().
Fixes: 6a643ddb56 ("net: introduce helper dev_change_tx_queue_len()")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_skb_with_frags uses __GFP_NORETRY for non-sleeping allocations
which is just a noop and a little bit confusing.
__GFP_NORETRY was added by ed98df3361 ("net: use __GFP_NORETRY for
high order allocations") to prevent from the OOM killer. Yet this was
not enough because fb05e7a89f ("net: don't wait for order-3 page
allocation") didn't want an excessive reclaim for non-costly orders
so it made it completely NOWAIT while it preserved __GFP_NORETRY in
place which is now redundant.
Drop the pointless __GFP_NORETRY because this function is used as
copy&paste source for other places.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the tunnel option type stored in tunnel flags when creating options
for tunnels. Thereby ensuring we do not set geneve, vxlan or erspan tunnel
options on interfaces that are not associated with them.
Make sure all users of the infrastructure set correct flags, for the BPF
helper we have to set all bits to keep backward compatibility.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the kernel accounts the memory for network traffic through
mem_cgroup_[un]charge_skmem() interface. However the memory accounted
only includes the truesize of sk_buff which does not include the size of
sock objects. In our production environment, with opt-out kmem
accounting, the sock kmem caches (TCP[v6], UDP[v6], RAW[v6], UNIX) are
among the top most charged kmem caches and consume a significant amount
of memory which can not be left as system overhead. So, this patch
converts the kmem caches of all sock objects to SLAB_ACCOUNT.
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ACLs implemented using either FIB rules or FIB entries, the BPF
program needs the FIB lookup status to be able to drop the packet.
Since the bpf_fib_lookup API has not reached a released kernel yet,
change the return code to contain an encoding of the FIB lookup
result and return the nexthop device index in the params struct.
In addition, inform the BPF program of any post FIB lookup reason as
to why the packet needs to go up the stack.
The fib result for unicast routes must have an egress device, so remove
the check that it is non-NULL.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sock reference is lost when scrubbing the packet and that breaks
TSQ (TCP Small Queues) and XPS (Transmit Packet Steering) causing
performance impacts of about 50% in a single TCP stream when crossing
network namespaces.
XPS breaks because the queue mapping stored in the socket is not
available, so another random queue might be selected when the stack
needs to transmit something like a TCP ACK, or TCP Retransmissions.
That causes packet re-ordering and/or performance issues.
TSQ breaks because it orphans the packet while it is still in the
host, so packets are queued contributing to the buffer bloat problem.
Preserving the sock reference fixes both issues. The socket is
orphaned anyways in the receiving path before any relevant action
and on TX side the netfilter checks if the reference is local before
use it.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In systems where neigh gc thresh holds are set to high values,
admin deleted neigh entries (eg ip neigh flush or ip neigh del) can
linger around in NUD_FAILED state for a long time until periodic gc kicks
in. This patch forces neigh_invalidate when NUD_FAILED neigh_update is
from an admin.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two rules with different values of suppress_prefix or suppress_ifgroup
are not the same. This fixes an -EEXIST when running:
$ ip -4 rule add table main suppress_prefixlength 0
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: f9d4b0c1e9 ("fib_rules: move common handling of newrule delrule msgs into fib_nl2rule")
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the performance of GRO receive by splitting flows into
multiple hash chains.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manage pending per-NAPI GRO packets via list_head.
Return an SKB pointer from the GRO receive handlers. When GRO receive
handlers return non-NULL, it means that this SKB needs to be completed
at this time and removed from the NAPI queue.
Several operations are greatly simplified by this transformation,
especially timing out the oldest SKB in the list when gro_count
exceeds MAX_GRO_SKBS, and napi_gro_flush() which walks the queue
in reverse order.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the xfrm interface id as a lookup key
for xfrm states and policies. With this we can assign
states and policies to virtual xfrm interfaces.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Benedict Wong <benedictwong@google.com>
Tested-by: Benedict Wong <benedictwong@google.com>
Tested-by: Antony Antony <antony@phenome.org>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
This "feature" is unused, undocumented, and untested and so doesn't
really belong. A patch is under development to properly implement
support for detecting when a search gets diverted down a different
chain, which the common purpose of nulls markers.
This patch actually fixes a bug too. The table resizing allows a
table to grow to 2^31 buckets, but the hash is truncated to 27 bits -
any growth beyond 2^27 is wasteful an ineffective.
This patch results in NULLS_MARKER(0) being used for all chains,
and leaves the use of rht_is_a_null() to test for it.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if dev_get_valid_name failed, propagate its return code
and remove the setting err to ENODEV, it will be set to
0 again before dev_change_net_namespace exits.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-06-16
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a panic in devmap handling in generic XDP where return type
of __devmap_lookup_elem() got changed recently but generic XDP
code missed the related update, from Toshiaki.
2) Fix a freeze when BPF progs are loaded that include BPF to BPF
calls when JIT is enabled where we would later bail out via error
path w/o dropping kallsyms, and another one to silence syzkaller
splats from locking prog read-only, from Daniel.
3) Fix a bug in test_offloads.py BPF selftest which must not assume
that the underlying system have no BPF progs loaded prior to test,
and one in bpftool to fix accuracy of program load time, from Jakub.
4) Fix a bug in bpftool's probe for availability of the bpf(2)
BPF_TASK_FD_QUERY subcommand, from Yonghong.
5) Fix a regression in AF_XDP's XDP_SKB receive path where queue
id check got erroneously removed, from Björn.
6) Fix missing state cleanup in BPF's xfrm tunnel test, from William.
7) Check tunnel type more accurately in BPF's tunnel collect metadata
kselftest, from Jian.
8) Fix missing Kconfig fragments for BPF kselftests, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
Commit 67f29e07e1 ("bpf: devmap introduce dev_map_enqueue") changed
the return value type of __devmap_lookup_elem() from struct net_device *
to struct bpf_dtab_netdev * but forgot to modify generic XDP code
accordingly.
Thus generic XDP incorrectly used struct bpf_dtab_netdev where struct
net_device is expected, then skb->dev was set to invalid value.
v2:
- Fix compiler warning without CONFIG_BPF_SYSCALL.
Fixes: 67f29e07e1 ("bpf: devmap introduce dev_map_enqueue")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 9ce33e4653 ("neighbour: support for NTF_EXT_LEARNED flag")
added support for NTF_EXT_LEARNED for neighbour entries.
NTF_EXT_LEARNED entries are neigh entries managed by control
plane (eg: Ethernet VPN implementation in FRR routing suite).
Periodic gc already excludes these entries. This patch extends
it to forced gc which the earlier patch missed.
Fixes: 9ce33e4653 ("neighbour: support for NTF_EXT_LEARNED flag")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the patch mentioned in the subject because it breaks at least
the Avahi mDNS daemon. That patch namely causes the Ubuntu 18.04 Avahi
daemon to fail to start:
Jun 12 09:49:24 ubuntu-vm avahi-daemon[529]: Successfully called chroot().
Jun 12 09:49:24 ubuntu-vm avahi-daemon[529]: Successfully dropped remaining capabilities.
Jun 12 09:49:24 ubuntu-vm avahi-daemon[529]: No service file found in /etc/avahi/services.
Jun 12 09:49:24 ubuntu-vm avahi-daemon[529]: SO_REUSEADDR failed: Structure needs cleaning
Jun 12 09:49:24 ubuntu-vm avahi-daemon[529]: SO_REUSEADDR failed: Structure needs cleaning
Jun 12 09:49:24 ubuntu-vm avahi-daemon[529]: Failed to create server: No suitable network protocol available
Jun 12 09:49:24 ubuntu-vm avahi-daemon[529]: avahi-daemon 0.7 exiting.
Jun 12 09:49:24 ubuntu-vm systemd[1]: avahi-daemon.service: Main process exited, code=exited, status=255/n/a
Jun 12 09:49:24 ubuntu-vm systemd[1]: avahi-daemon.service: Failed with result 'exit-code'.
Jun 12 09:49:24 ubuntu-vm systemd[1]: Failed to start Avahi mDNS/DNS-SD Stack.
Fixes: f396922d86 ("net: do not allow changing SO_REUSEADDR/SO_REUSEPORT on bound sockets")
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
-----BEGIN PGP SIGNATURE-----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=10u6
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20180605' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"Another reasonable chunk of audit changes for v4.18, thirteen patches
in total.
The thirteen patches can mostly be broken down into one of four
categories: general bug fixes, accessor functions for audit state
stored in the task_struct, negative filter matches on executable
names, and extending the (relatively) new seccomp logging knobs to the
audit subsystem.
The main driver for the accessor functions from Richard are the
changes we're working on to associate audit events with containers,
but I think they have some standalone value too so I figured it would
be good to get them in now.
The seccomp/audit patches from Tyler apply the seccomp logging
improvements from a few releases ago to audit's seccomp logging;
starting with this patchset the changes in
/proc/sys/kernel/seccomp/actions_logged should apply to both the
standard kernel logging and audit.
As usual, everything passes the audit-testsuite and it happens to
merge cleanly with your tree"
[ Heh, except it had trivial merge conflicts with the SELinux tree that
also came in from Paul - Linus ]
* tag 'audit-pr-20180605' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: Fix wrong task in comparison of session ID
audit: use existing session info function
audit: normalize loginuid read access
audit: use new audit_context access funciton for seccomp_actions_logged
audit: use inline function to set audit context
audit: use inline function to get audit context
audit: convert sessionid unset to a macro
seccomp: Don't special case audited processes when logging
seccomp: Audit attempts to modify the actions_logged sysctl
seccomp: Configurable separator for the actions_logged string
seccomp: Separate read and write code for actions_logged sysctl
audit: allow not equal op for audit by executable
audit: add syscall information to FEATURE_CHANGE records
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-06-05
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a new BPF hook for sendmsg similar to existing hooks for bind and
connect: "This allows to override source IP (including the case when it's
set via cmsg(3)) and destination IP:port for unconnected UDP (slow path).
TCP and connected UDP (fast path) are not affected. This makes UDP support
complete, that is, connected UDP is handled by connect hooks, unconnected
by sendmsg ones.", from Andrey.
2) Rework of the AF_XDP API to allow extending it in future for type writer
model if necessary. In this mode a memory window is passed to hardware
and multiple frames might be filled into that window instead of just one
that is the case in the current fixed frame-size model. With the new
changes made this can be supported without having to add a new descriptor
format. Also, core bits for the zero-copy support for AF_XDP have been
merged as agreed upon, where i40e bits will be routed via Jeff later on.
Various improvements to documentation and sample programs included as
well, all from Björn and Magnus.
3) Given BPF's flexibility, a new program type has been added to implement
infrared decoders. Quote: "The kernel IR decoders support the most
widely used IR protocols, but there are many protocols which are not
supported. [...] There is a 'long tail' of unsupported IR protocols,
for which lircd is need to decode the IR. IR encoding is done in such
a way that some simple circuit can decode it; therefore, BPF is ideal.
[...] user-space can define a decoder in BPF, attach it to the rc
device through the lirc chardev.", from Sean.
4) Several improvements and fixes to BPF core, among others, dumping map
and prog IDs into fdinfo which is a straight forward way to correlate
BPF objects used by applications, removing an indirect call and therefore
retpoline in all map lookup/update/delete calls by invoking the callback
directly for 64 bit archs, adding a new bpf_skb_cgroup_id() BPF helper
for tc BPF programs to have an efficient way of looking up cgroup v2 id
for policy or other use cases. Fixes to make sure we zero tunnel/xfrm
state that hasn't been filled, to allow context access wrt pt_regs in
32 bit archs for tracing, and last but not least various test cases
for fixes that landed in bpf earlier, from Daniel.
5) Get rid of the ndo_xdp_flush API and extend the ndo_xdp_xmit with
a XDP_XMIT_FLUSH flag instead which allows to avoid one indirect
call as flushing is now merged directly into ndo_xdp_xmit(), from Jesper.
6) Add a new bpf_get_current_cgroup_id() helper that can be used in
tracing to retrieve the cgroup id from the current process in order
to allow for e.g. aggregation of container-level events, from Yonghong.
7) Two follow-up fixes for BTF to reject invalid input values and
related to that also two test cases for BPF kselftests, from Martin.
8) Various API improvements to the bpf_fib_lookup() helper, that is,
dropping MPLS bits which are not fully hashed out yet, rejecting
invalid helper flags, returning error for unsupported address
families as well as renaming flowlabel to flowinfo, from David.
9) Various fixes and improvements to sockmap BPF kselftests in particular
in proper error detection and data verification, from Prashant.
10) Two arm32 BPF JIT improvements. One is to fix imm range check with
regards to whether immediate fits into 24 bits, and a naming cleanup
to get functions related to rsh handling consistent to those handling
lsh, from Wang.
11) Two compile warning fixes in BPF, one for BTF and a false positive
to silent gcc in stack_map_get_build_id_offset(), from Arnd.
12) Add missing seg6.h header into tools include infrastructure in order
to fix compilation of BPF kselftests, from Mathieu.
13) Several formatting cleanups in the BPF UAPI helper description that
also fix an error during rst2man compilation, from Quentin.
14) Hide an unused variable in sk_msg_convert_ctx_access() when IPv6 is
not built into the kernel, from Yue.
15) Remove a useless double assignment in dev_map_enqueue(), from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack argument to reload, port_split and port_unsplit operations.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here, a new type of allocator support is added to the XDP return
API. A zero-copy allocated xdp_buff cannot be converted to an
xdp_frame. Instead is the buff has to be copied. This is not supported
at all in this commit.
Also, an opaque "handle" is added to xdp_buff. This can be used as a
context for the zero-copy allocator implementation.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It is not safe to do so because such sockets are already in the
hash tables and changing these options can result in invalidating
the tb->fastreuse(port) caching.
This can have later far reaching consequences wrt. bind conflict checks
which rely on these caches (for optimization purposes).
Not to mention that you can currently end up with two identical
non-reuseport listening sockets bound to the same local ip:port
by clearing reuseport on them after they've already both been bound.
There is unfortunately no EISBOUND error or anything similar,
and EISCONN seems to be misleading for a bound-but-not-connected
socket, so use EUCLEAN 'Structure needs cleaning' which AFAICT
is the closest you can get to meaning 'socket in bad state'.
(although perhaps EINVAL wouldn't be a bad choice either?)
This does unfortunately run the risk of breaking buggy
userspace programs...
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Change-Id: I77c2b3429b2fdf42671eee0fa7a8ba721c94963b
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull aio updates from Al Viro:
"Majority of AIO stuff this cycle. aio-fsync and aio-poll, mostly.
The only thing I'm holding back for a day or so is Adam's aio ioprio -
his last-minute fixup is trivial (missing stub in !CONFIG_BLOCK case),
but let it sit in -next for decency sake..."
* 'work.aio-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
aio: sanitize the limit checking in io_submit(2)
aio: fold do_io_submit() into callers
aio: shift copyin of iocb into io_submit_one()
aio_read_events_ring(): make a bit more readable
aio: all callers of aio_{read,write,fsync,poll} treat 0 and -EIOCBQUEUED the same way
aio: take list removal to (some) callers of aio_complete()
aio: add missing break for the IOCB_CMD_FDSYNC case
random: convert to ->poll_mask
timerfd: convert to ->poll_mask
eventfd: switch to ->poll_mask
pipe: convert to ->poll_mask
crypto: af_alg: convert to ->poll_mask
net/rxrpc: convert to ->poll_mask
net/iucv: convert to ->poll_mask
net/phonet: convert to ->poll_mask
net/nfc: convert to ->poll_mask
net/caif: convert to ->poll_mask
net/bluetooth: convert to ->poll_mask
net/sctp: convert to ->poll_mask
net/tipc: convert to ->poll_mask
...
- replaceme the force_dma flag with a dma_configure bus method.
(Nipun Gupta, although one patch is іncorrectly attributed to me
due to a git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few cleanups
to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
-----BEGIN PGP SIGNATURE-----
iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlsU1hwLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYPraxAAocC7JiFKW133/VugCtGA1x9uE8DPHealtsWTAeEq
KOOB3GxWMU2hKqQ4km5tcfdWoGJvvab6hmDXcitzZGi2JajO7Ae0FwIy3yvxSIKm
iH/ON7c4sJt8gKrXYsLVylmwDaimNs4a6xfODoCRgnWuovI2QrrZzupnlzPNsiOC
lv8ezzcW+Ay/gvDD/r72psO+w3QELETif/OzR/qTOtvLrVabM06eHmPQ8Wb98smu
/UPMMv6/3XwQnxpxpdyqN+p/gUdneXithzT261wTeZ+8gDXmcWBwHGcMBCimcoBi
FklW52moazIPIsTysqoNlVFsLGJTeS4p2D3BLAp5NwWYsLv+zHUVZsI1JY/8u5Ox
mM11LIfvu9JtUzaqD9SvxlxIeLhhYZZGnUoV3bQAkpHSQhN/xp2YXd5NWSo5ac2O
dch83+laZkZgd6ryw6USpt/YTPM/UHBYy7IeGGHX/PbmAke0ZlvA6Rae7kA5DG59
7GaLdwQyrHp8uGFgwze8P+R4POSk1ly73HHLBT/pFKnDD7niWCPAnBzuuEQGJs00
0zuyWLQyzOj1l6HCAcMNyGnYSsMp8Fx0fvEmKR/EYs8O83eJKXi6L9aizMZx4v1J
0wTolUWH6SIIdz474YmewhG5YOLY7mfe9E8aNr8zJFdwRZqwaALKoteRGUxa3f6e
zUE=
=6Acj
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
Some of the code paths calculating flow hash for IPv6 use flowlabel member
of struct flowi6 which, despite its name, encodes both flow label and
traffic class. If traffic class changes within a TCP connection (as e.g.
ssh does), ECMP route can switch between path. It's also inconsistent with
other code paths where ip6_flowlabel() (returning only flow label) is used
to feed the key.
Use only flow label everywhere, including one place where hash key is set
using ip6_flowinfo().
Fixes: 51ebd31815 ("ipv6: add support of equal cost multipath (ECMP)")
Fixes: f70ea018da ("net: Add functions to get skb->hash based on flow structures")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the code paths calculating flow hash for IPv6 use flowlabel member
of struct flowi6 which, despite its name, encodes both flow label and
traffic class. If traffic class changes within a TCP connection (as e.g.
ssh does), ECMP route can switch between path. It's also incosistent with
other code paths where ip6_flowlabel() (returning only flow label) is used
to feed the key.
Use only flow label everywhere, including one place where hash key is set
using ip6_flowinfo().
Fixes: 51ebd31815 ("ipv6: add support of equal cost multipath (ECMP)")
Fixes: f70ea018da ("net: Add functions to get skb->hash based on flow structures")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Michal noted the flow struct takes both the flow label and priority.
Update the bpf_fib_lookup API to note that it is flowinfo and not just
the flow label.
Cc: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This is the first real user of the XDP_XMIT_FLUSH flag.
As pointed out many times, XDP_REDIRECT without using BPF maps is
significant slower than the map variant. This is primary due to the
lack of bulking, as the ndo_xdp_flush operation is required after each
frame (to avoid frames hanging on the egress device).
It is still possible to optimize this case. Instead of invoking two
NDO indirect calls, which are very expensive with CONFIG_RETPOLINE,
instead instruct ndo_xdp_xmit to flush via XDP_XMIT_FLUSH flag.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
