Save dynamic FIFO read only information for later uses during
musb_save/restore_context functions.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB's programming guide dictates how we should handle its
irqs and in which order. Follow that.
Signed-off-by: Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The version applied had a few comments which are now
done.
Thanks to Sergei for pointing out.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the Tx abort/teardown logic. We now wait for the teardown
completion interrupt and acknowledge the same by setting the tx_complete
register to 0.
This change is needed to ensure that abort processing works on DM365 platform.
Without this change after completion of abort processing the system is
overwhelmed with continuous stream of abort interrupts.
This change has been tested on all CPPI3.x platforms (DM644x, DM646x, DM35x,
DM36x).
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements the work around for a Mentor controller related
bug where it's observed a BULK Tx toggle error on the bus when a
BULK IO gets scheduled on an endpoint that was earlier used for
handling ISOC transaction and needed to start on 1 toggle. When such
a situation arises even if the TXCSR toggle bits are programmed
correctly by the musb driver the data gets transmitted with 0 toggle
which leads to toggle error on the bus and the BULK transaction fails.
In case of MSC write, the device gets reset by the Host.
This Mentor bug is observed on almost all Mentor versions (1.3, 1.5,
1.8). Confirmed on DM644x, DM355, DM365, OMAPL13x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB DMA_INTR register may sometimes read zero when infact there
was a pending interrupt. Workaround this by reading the DMA_COUNT
values for all enabled channels when this condition occurs.
Flag these channels as the ones needing to be serviced.
Additionally, the absence of a debug print meant we would never
catch a spurious DMA interrupt in MUSB. So this patch adds a
debug print in the IRQ handler.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a wrapper for reading the DMA count register, analogous
to the one for writing to this register.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have observed MSC data read corruption when USB LAN device is
also connected and it's interface is up.
Silicon team has confirmed an errata where in all the active
transfers should use FIFO space either in first 8K or next 8K.
So far we have observed the issue in above use case scenario.
As a workaround to it, adding a new FIFO config (5) fitting well
within first 8K which can be used for such use cases.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
move to request_threaded_irq() on twl4030 children.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Under the new system a device cannot be suspended against
the driver's wish. Therefore this condition no longer needs
to be checked for.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return values are being initialised to zero only to be unconditionally
assigned to a few instructions later. This may give the impression that
zero is returned on success, which is not the case.
Note also that ftdi_NDI_device_setup never reports errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also remove unnecessary buffer allocations for zero-length transfers.
Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also fixes DMA transfer to stack for latency buffer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's really the wireless speed, so rename the thing to make
more sense. Based on a recommendation from David Vrabel
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently a non-root-hub USB device's wakeup settings are initialized when the
device is set to a configured state using device_init_wakeup(), but this is not
correct as wakeup is split into "capable" (can_wakeup) and "enabled"
(should_wakeup). The settings should be initialized instead in the device
initialization (usb_new_device) with the "capable" setting disabled and the
"enabled" setting enabled. The "capable" setting should be set based on the
device being configured or unconfigured, and "enabled" setting set based on
the sysfs power/wakeup control.
This patch retains the sysfs power/wakeup setting of a non-root-hub USB device
over a USB device re-configuration, which can happen (for example) after a
suspend/resume cycle.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pbLua console port is known to not be a modem, so it is
unnecessary to be told this when it is plugged in.
Add NOT_A_MODEM quirk to tell the driver that we know this already
and hence not to warn us, and mark the pbLua console port.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pbLua firmware (http://pblua.com/) for the Lego Mindstorms NXT
provides a CDC ACM port for it's serial console.
This used to be detected automatically, but this support has been
dropped, probably for sensible reasons.
Explicitly add support for this device by adding an item to the
device ID table.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to a simple oversight when bus zero was added, the text API fails to
deliver the bus number in 'E' messages (which are equivalent of 'C'
messages, only for error case). This makes it harder, for instance,
use a search-and-highlight in a text editor. So fix it.
Also, Alan Stern requested adding timestamps to 'E' messages. This is
purely cosmetic, but makes it easier to read the trace. This is done
for both text and binary APIs.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it's easier to keep up and add more sysfs entries
as necessary.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Normally, the musb uses ep1 as the bidirectional bulk endpoint. This won't
work on the Blackfin musb as all endpoints (except ep0) are unidirectional.
Further, ep1-ep4 have a small 128 byte FIFO which makes them undesirable
for bulk endpoints (which need more like a 512 byte FIFO). This leaves us
with ep5-ep7 which have 1024 byte FIFOs and can be configured as either
in/out and bulk/interrupt/iso on the fly.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've got a crappy cypress converter here, and while running at higher
baud rates craps out on throughput, it works fine with lower ones.
While it'd be nice to simply use a lower baud rate, not all devices
can be configured this way, and it is possible to (slowly) interact
at higher rates by sending a byte at a time. So let people force
higher rates when they need it via a module parameter.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current code has a confusing duplicate new_baudrate init when setting
the serial parameters. So just combine the if statement checks to avoid
this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB_SERIAL_DEBUG Kconfig is for the USB serial debug driver, not for
generically enabling debug output in random USB serial drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices which use mode switching revert to their
primary mode as they are reset. They must not be reset for
error handling. As user spaces makes the switch it also
has to tell the kernel that a device is quirky.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices must be switched to a new mode to fully use them.
A reset would make them revert to the old mode. Therefore a reset
must not be used for error handling with such devices.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it's expected that the transceiver driver will
initialize and call the notifier chain when
necessary. Implement that for twl4030-usb driver.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The notifier will be used to communicate usb events
to other drivers like the charger chip.
This can be used as source of information to kick
usb charger detection as described by the USB
Battery Charging Specification 1.1 and/or to
pass bMaxPower field of selected usb_configuration
to charger chip in order to use that information
as input current on the charging profile
setup.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An incorrect sizeof() resulted in only 4 (or 8) octets of the CHID being
checked instead of all 16 octets. A randomly generated CHID had a
probability of being unable to start a WUSB host of less than 1 in
2 billion.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xhci_add_endpoint() is used in the reset path. It must
use GFP_NOIO to avoid a possible deadlock.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update cdc-acm to the async methods eliminating the workqueue
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use platform_get_resource() to fetch the memory resource and
resource_size() for calculate the length.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI FSL controller preserve its state during sleep mode, so nothing
fancy needs to be done.
Though, during 'deep sleep' mode (as found in MPC831x CPUs) the
controller turns off and needs to be reinitialized upon resume.
This patch adds support for hibernation and resuming after deep sleep.
Based on Dave Liu and Jerry Huang's work[1].
[1] http://www.bitshrine.org/gpp/linux-fsl-2.6.24.3-MPC8315ERDB-usb-power-mangement.patch
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes following warnings:
ehci-fsl.c:43:5: warning: symbol 'usb_hcd_fsl_probe' was not declared. Should it be static?
ehci-fsl.c:150:6: warning: symbol 'usb_hcd_fsl_remove' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fix audio record functionality for some Full speed sound blaster devices.
Issue: Sometimes transaction complete indication is coming from HW one frame later.
Solution: If scan_periodic process now frame or previous frame now-1 and sitd transaction
is not finished yet, exit scan_periodic function and check the same transaction in the next frame.
Signed-off-by: Dimitry Epshtein <dima@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sometimes disable_periodic() stop scan_periodic before than free_cached_itd_list() was called.
In such case USB Host stacked during disconnect operation
Solution: add call of free_cached_itd_list() function in disable_periodic()
Signed-off-by: Dimitry Epshtein <dima@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
