Clock nodes shall use the services provided by underlying drivers to access
the hardware registers instead of direct memory read/write. Thus, change
all the code to use the new omap2_clk_readl / omap2_clk_writel APIs for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Using indexed memmaps is required for isolating the actual memory access
from the clock code. Now, the driver providing the support for the clock IP
block provides the low level routines for reading/writing clock registers
also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the AM43xx power,
reset and clock manager (PRCM).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
AM35xx now uses the clock data from device tree. Most of the data is
shared with OMAP3xxx, but as there is some delta, a new base .dtsi
file is also created for the SoC.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the OMAP3 power,
reset and clock manager (PRCM).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the AM33xx power,
reset and clock manager (PRCM).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds optfclk_pciephy_clk and optfclk_pciephy_div_clk
which are used by PCIe phy. It also adds a mux clock to choose
the source of optfclk_pciephy_div_clk clock.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch changes apll_pcie_m2_ck to fixed factor
clock as there are no configurable divider associated to m2.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The patch adds a mux node to choose the parent of apll_pcie_ck node.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the DRA7 power,
reset and clock manager (PRCM).
TODO: apll_pcie clock node is still a dummy in this version, and
proper support for the APLL should be added.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the OMAP5 power,
reset and clock manager (PRCM).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch creates a unique node for each clock in the OMAP4 power,
reset and clock manager (PRCM). OMAP443x and OMAP446x have slightly
different clock tree which is taken into account in the data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-3xxx.c now contains the clock init functionality for omap3, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
OMAP3 has interface clocks in addition to functional clocks, which
require special handling for the autoidle and idle status register
offsets mainly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-33xx.c now contains the clock init functionality for am33xx, including
DT clock registration and adding of static clkdev entries.
This patch also moves the omap2_clk_enable_init_clocks declaration to
the driver include, as this is needed by the am33xx clock init code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-54xx.c now contains the clock init functionality for omap5, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-44xx.c now contains the clock init functionality for omap4, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a multipurpose clock node, which contains support for multiple
sub-clocks. Uses basic composite clock type to implement the actual
functionality, and TI specific gate, mux and divider clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
TI clk driver now routes some of the basic clocks through own
registration routine to allow autoidle support. This routine just
checks a couple of device node properties and adds autoidle support
if required, and just passes the registration forward to basic clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The OMAP clock driver now supports DPLL clock type. This patch also
adds support for DT DPLL nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
SOC_DRA7XX was under wrong menu within Kconfig file, which prevented
DRA7XX only build. Fixed the kconfig options for this SoC as we are
there. voltage.c needs to be added to the DRA7XX build also, otherwise
DRA7XX only build will fail.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DRA7XX and AM43XX were missing common clock code from the Makefile, which
causes build breakage in DRA7XX / AM43XX only builds once clock support
for these SoCs is added. Add the missing entries to the Makefile as
preparation of this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a label and #clock-cells property to device node of
max77686 PMIC to allow using it as a clock provider.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Specify the remaining input clocks (pll_ref, pll_in, and sclk_pcm_in)
for the AudioSS clock controller.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Specify pll_ref, pll_in, sclk_audio, and sclk_pcm_in for the AudioSS
clock controller.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Due to incorrect clock specified in MDMA0 node, using MDMA0 controller
could cause system failures, due to wrong clock being controlled. This
patch fixes this by specifying correct clock.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Corrected commit message and description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=3A1e
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Fix a regression for wrong interrupt numbers for some devices after
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
* tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
+ v3.13-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa418 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by 4dcfa60071
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by 22ceeee16e
("pwm-backlight: Add power supply support") in v3.12.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6ai1
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second Round of Renesas ARM based SoC Fixes for v3.13
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa418 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by 4dcfa60071
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by 22ceeee16e
("pwm-backlight: Add power supply support") in v3.12.
* tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
After commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit b144e4ab1e
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.
However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:
This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.
Before commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.
Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=kOrX
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13-rc/hwmod-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into debug-ll-and-ldp-backlight-fix
A few OMAP hwmod fixes for v3.13-rc. One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
Looks like the LCD panel on LDP has been broken quite a while, and
recently got fixed by commit 0b2aa8bed3 (gpio: twl4030: Fix regression
for twl gpio output). However, there's still an issue left where the panel
backlight does not come on if the LCD drivers are built into the
kernel.
Fix the issue by registering the DPI LCD panel only after the twl4030
GPIO has probed.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated per Tomi's comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit
ec2c082 (ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ)
updated the way interrupts for OMAP2/3 devices are defined in the
HWMOD data structures to being an index plus a fixed offset (defined
by OMAP_INTC_START).
Couple of irqs in the OMAP2/3 hwmod data were misconfigured completely
as they were missing this OMAP_INTC_START relative offset. Add this
offset back to fix the incorrect irq data for the following modules:
OMAP2 - GPMC, RNG
OMAP3 - GPMC, ISP MMU & IVA MMU
Signed-off-by: Suman Anna <s-anna@ti.com>
Fixes: 7d7e1eba7e ("ARM: OMAP2+: Prepare for irqs.h removal")
Fixes: ec2c0825ca ("ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With commit '7dedd34: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with
DEBUG_LL' we moved from parsing cmdline to identify uart used for earlycon
to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS.
On DRA7 though, we seem to be missing this flag, and atleast on the DRA7 EVM
where we use uart1 for console, boot fails with DEBUG_LL enabled.
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com> # on a different base
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Fixes: 7dedd34694 ("ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Much smaller batch of fixes this week.
Biggest one is a revert of an OMAP display change that removed some non-DT
pinmux code that was still needed for 3.13 to get DSI displays to work.
There's also a fix that resolves some misdescribed GPIO controller
resources on shmobile. The rest are mostly smaller fixes, a couple of
MAINTAINERS updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6Nj7
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Much smaller batch of fixes this week.
Biggest one is a revert of an OMAP display change that removed some
non-DT pinmux code that was still needed for 3.13 to get DSI displays
to work.
There's also a fix that resolves some misdescribed GPIO controller
resources on shmobile. The rest are mostly smaller fixes, a couple of
MAINTAINERS updates, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
MAINTAINERS: Add keystone clock drivers
MAINTAINERS: Add keystone git tree information
ARM: s3c64xx: dt: Fix boot failure due to double clock initialization
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
* r8a7790 (R-Car H1) SoC
- Correct GPIO resources in DT.
This problem has been present since GPIOs were added to the r8a7790 SoC
by f98e10c88a ("ARM: shmobile: r8a7790: Add GPIO controller
devices to device tree") in v3.12-rc1.
* irqchip renesas-intc-irqpin
- Correct register bitfield shift calculation
This bug has been present since the renesas-intc-irqpin driver was
introduced by 443580486e ("irqchip: Renesas INTC External IRQ pin
driver") in v3.10-rc1
* Lager board
- Do not build the phy fixup unless CONFIG_PHYLIB is enabled
This problem was introduced by 48c8b96f21
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=Vbzt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Renesas ARM based SoC fixes for v3.13
* r8a7790 (R-Car H1) SoC
- Correct GPIO resources in DT.
This problem has been present since GPIOs were added to the r8a7790 SoC
by f98e10c88a ("ARM: shmobile: r8a7790: Add GPIO controller
devices to device tree") in v3.12-rc1.
* irqchip renesas-intc-irqpin
- Correct register bitfield shift calculation
This bug has been present since the renesas-intc-irqpin driver was
introduced by 443580486e ("irqchip: Renesas INTC External IRQ pin
driver") in v3.10-rc1
* Lager board
- Do not build the phy fixup unless CONFIG_PHYLIB is enabled
This problem was introduced by 48c8b96f21
* tag 'renesas-fixes-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- Fix balloon driver for auto-translate guests (PVHVM, ARM) to not use
scratch pages.
- Fix block API header for ARM32 and ARM64 to have proper layout
- On ARM when mapping guests, stick on PTE_SPECIAL
- When using SWIOTLB under ARM, don't call swiotlb functions twice
- When unmapping guests memory and if we fail, don't return pages which
failed to be unmapped.
- Grant driver was using the wrong address on ARM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSsdFEAAoJEFjIrFwIi8fJDQwIAL1ygSTwSXdH6TlqtD9GVdsE
G6kiCM7G6VXrKMf8zBtgbGpcl6FT0zOIz4cRcXbyDniuHTjdWuH9dlmZOzFMAirE
uMWwOB1EfmRBEJRsd2pW0Gj0O6VABWh8BHklFCeWUvk/Stlw9uXqIwf7Pjcj6wPT
XW+ZywqsAve4MM60Rz/nMsakLcTK4i5SCRgPPFgAnPKUod3f/QbEHwci/lpinJFv
AuQp2JytCsDc2nehEi1kMwEx7LLBlUcjXTqPG5lhQnXrFleDtMdCJd9dGjeze7Qu
F5sftfdlp18ojQwegv1PGiVI4jV8rIq29ybaef/y9DLd3nC3rmi8B8/m9RG2qyI=
=dUsw
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.13-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Fix balloon driver for auto-translate guests (PVHVM, ARM) to not use
scratch pages.
- Fix block API header for ARM32 and ARM64 to have proper layout
- On ARM when mapping guests, stick on PTE_SPECIAL
- When using SWIOTLB under ARM, don't call swiotlb functions twice
- When unmapping guests memory and if we fail, don't return pages which
failed to be unmapped.
- Grant driver was using the wrong address on ARM.
* tag 'stable/for-linus-3.13-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: Seperate the auto-translate logic properly (v2)
xen/block: Correctly define structures in public headers on ARM32 and ARM64
arm: xen: foreign mapping PTEs are special.
xen/arm64: do not call the swiotlb functions twice
xen: privcmd: do not return pages which we have failed to unmap
XEN: Grant table address, xen_hvm_resume_frames, is a phys_addr not a pfn
dead code as omap4 has been booting with device tree only since
v3.10. Turns out I also removed some display related mux code,
so let's revert that except for the dead code parts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=gI+4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/display-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
I accidentally removed some mux code for omap4 that I thought was
dead code as omap4 has been booting with device tree only since
v3.10. Turns out I also removed some display related mux code,
so let's revert that except for the dead code parts.
* tag 'omap-for-v3.13/display-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (439 commits)
Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
+Linux 3.13-rc4
The r8a7790.dtsi file has four sdhi nodes which the first two have the wrong
resource size for their register block. This causes the sh_modbile_sdhi driver
to fail to communicate with card at-all.
Change sdhi{0,1} node size from 0x100 to 0x200 to correct these nodes
as per Kuninori Morimoto's response to the original patch where all four
nodes where changed. sdhi{2,3} are the correct size.
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa418 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: William Towle <william.towle@codethink.co.uk>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
4dcfa60071
(ARM: DMA-API: better handing of DMA masks for coherent allocations)
exchanged DMA mask check method.
Below warning will appear without this patch
asoc-simple-card asoc-simple-card.0: \
Coherent DMA mask 0xffffffffffffffff is larger than dma_addr_t allows
asoc-simple-card asoc-simple-card.0: \
Driver did not use or check the return value from dma_set_coherent_mask()?
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 22ceeee16e ("pwm-backlight: Add
power supply support") added a mandatory power supply for the PWM
backlight. Add a fixed 5V regulator to board code with a consumer supply
entry for the backlight device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit ad11cb9a5cf96346f1240995c672cdbb5501785c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit e30b06f4d5 (ARM: OMAP2+: Remove
legacy mux code for display.c) removed non-DT DSI and HDMI pinmuxing.
However, DSI pinmuxing is still needed, and removing that caused DSI
displays not to work.
This reverts the DSI parts of the commit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit
4178bac ARM: call of_clk_init from default time_init handler
added implicit call to of_clk_init() from default time_init callback,
but it did not change platforms calling it from other callbacks, despite
of not having custom time_init callbacks. This caused double clock
initialization on such platforms, leading to boot failures. An example
of such platform is mach-s3c64xx.
This patch fixes boot failure on s3c64xx by dropping custom init_irq
callback, which had a call to of_clk_init() and moving system reset
initialization to init_machine callback. This allows us to have
clocks initialized properly without a need to have custom init_time or
init_irq callbacks.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
"This resolves some further issues with the dma mask changes on ARM
which have been found by TI and others, and also some corner cases
with the updates to the virtual to physical address translations.
Konstantin also found some problems with the unwinder, which now
performs tighter verification that the stack is valid while unwinding"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix asm/memory.h build error
ARM: 7917/1: cacheflush: correctly limit range of memory region being flushed
ARM: 7913/1: fix framepointer check in unwind_frame
ARM: 7912/1: check stack pointer in get_wchan
ARM: 7909/1: mm: Call setup_dma_zone() post early_paging_init()
ARM: 7908/1: mm: Fix the arm_dma_limit calculation
ARM: another fix for the DMA mapping checks
Jason Gunthorpe reports a build failure when ARM_PATCH_PHYS_VIRT is
not defined:
In file included from arch/arm/include/asm/page.h:163:0,
from include/linux/mm_types.h:16,
from include/linux/sched.h:24,
from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function '__virt_to_phys':
arch/arm/include/asm/memory.h:244:40: error: 'PHYS_OFFSET' undeclared (first use in this function)
arch/arm/include/asm/memory.h:244:40: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/include/asm/memory.h: In function '__phys_to_virt':
arch/arm/include/asm/memory.h:249:13: error: 'PHYS_OFFSET' undeclared (first use in this function)
Fixes: ca5a45c06c ("ARM: mm: use phys_addr_t appropriately in p2v and v2p conversions")
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Allwinner A31 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A31 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Olof Johansson <olof@lixom.net>
The Allwinner A20 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A20 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org #3.12+
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a missing break to the switch in tegra_init_fuse() which determines
which SoC the code is running on. This prevents the Tegra30+ fuse
handling code from running on Tegra20.
Fixes: 3bd1ae57f7 ("ARM: tegra: add fuses as device randomness")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.
If SDRAM is not reset, it causes memory bus congestion and
the device hangs. We put SDRAM in selfresh mode before watchdog
reset, removing potential freezes.
Without this patch PXA270-based ICP DAS LP-8x4x hangs after up to 40
reboots. With this patch it has successfully rebooted 500 times.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
