Disabling pipe/transcoder clock before power down sink could cause
sink lost signal, causing it to trigger a hotplug to notify source
that link signal was lost.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191202222513.337777-2-jose.souza@intel.com
If the CRTC is going from enabled to disabled and it is a port sync
slave, it needs to check to the old state to be disabled before the
port sync master.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191202222513.337777-1-jose.souza@intel.com
Let's move handling and reset for gen11 display IRQs to their own
functions, similar to how we deal with GT interrupts. This will make
the top-level functions a bit easier to read and potentially make things
easier to deal with in the future if new platforms wind up needing
different display handling logic.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191202171608.3361125-1-matthew.d.roper@intel.com
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Rather than assume if and only if the engine->default_state is not set
that the context is invalid, instead track when we know the context has
valid state -- either because we have copied the default_state or we
have completed a context switch to save the HW state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203124155.3019926-1-chris@chris-wilson.co.uk
Only along the submission path can we guarantee that the locked request
is indeed from a foreign engine, and so the nesting of engine/rq is
permissible. On the submission tasklet (process_csb()), we may find
ourselves competing with the normal nesting of rq/engine, invalidating
our nesting. As we only use the spinlock for debug purposes, skip the
debug if we cannot acquire the spinlock for safe validation - catching
99% of the bugs is better than causing a hard lockup.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: c95d31c3df ("drm/i915/execlists: Lock the request while validating it during promotion")
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203152631.3107653-2-chris@chris-wilson.co.uk
Similar to for i915_active.mutex, we require each class of i915_active
to have distinct lockdep chains as some, but by no means all,
i915_active are used within the shrinker and so have much more severe
usage constraints. By using a lockclass local to i915_active_init() all
i915_active workers have the same lock class, and we may generate false
positives when waiting for the i915_active. If we push the lockclass
into the caller, each class of i915_active will have distinct lockdep
chains.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191202140133.2444217-1-chris@chris-wilson.co.uk
The unaligned ioread32() will make us read byte by byte looking for the
vbt. We could just as well have done a ioread8() + a shift and avoid the
extra confusion on how we are looking for "$VBT".
However when using ACPI it's guaranteed the VBT is 4-byte aligned
per spec, so we can probably assume it here as well.
v2: do not try to simplify the loop by eliminating the auxiliary counter
(Jani and Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191126225110.8127-4-lucas.demarchi@intel.com
We don't need to keep the pci rom mapped during the entire
intel_bios_init() anymore. Move it to the previous copy_vbt() function
and rename it to oprom_get_vbt() since now it's responsible to to all
operations related to get the vbt from the oprom.
v2: fix double __iomem attribute detected by sparse
v3: fix missing unmap on success (Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191126225110.8127-3-lucas.demarchi@intel.com
When we map the VBT through pci_map_rom() we may not be allowed
to simply discard the address space and go on reading the memory.
That doesn't work on my test system, but by dumping the rom via
sysfs I can can get the correct vbt. So change our find_vbt() to do
the same as done by pci_read_rom(), i.e. use memcpy_fromio().
v2: the just the minimal changes by not bothering with the unaligned io
reads: this can be done on top (from Ville and Jani)
v3: drop const in function return since now we are copying the vbt,
rather than just finding it
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191126225110.8127-2-lucas.demarchi@intel.com
From VBT 228+ this is block that PSR and other power saving
features configuration should be read from.
v3:
Using DRRS from this new block
v4:
Using BIT()
Fixing DRRS comment in parse_power_conservation_features()
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128014852.214135-5-jose.souza@intel.com
eDP specification states that sink can have its PSR capability
changed, I have never found any panel doing that but lets add that
for completeness.
For now it is not reading back the PSR capabilities and if possible
re-enabling PSR, this will be added if a panel is found using this
feature.
v4:
Cleaning DP_PSR_CAPS_CHANGE
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128014852.214135-4-jose.souza@intel.com
When this error happens sink link is not stable after the required
FW_EXIT_LATENCY period so it will miss the selective update.
As the other PSR errors, for now we are not trying to recover from
it.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128014852.214135-3-jose.souza@intel.com
eDP spec states that when sink enconters a problem that prevents it
to keep PSR running it should set PSR status to internal error and
set the reason why it happen to PSR_ERROR_STATUS but it is not how it
was implemented.
But also I don't want to change this behavior, who knows if there is
a panel out there that only set the PSR_ERROR_STATUS.
So here refactoring the code a bit to make more easy to read what was
state above as more checks will be added to this function.
v2:
returning a int instead of a bool in psr_get_status_and_error_status()
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128014852.214135-2-jose.souza@intel.com
PSR2 HW only support a limited number of bits per pixel, if mode has
more than supported PSR2 should not be enabled.
BSpec: 50422
BSpec: 7713
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128014852.214135-1-jose.souza@intel.com
The "err" label is not really "err", but rather "out" since the return
path is shared between error condition and normal path. This broke when
commit 03cea61076 ("drm/i915/dsb: fix extra warning on error path
handling") added a "dsb->cmd_buf = NULL;" there, making DSB to stop
working since now all writes would pass-through via mmio.
Remove the set to NULL since it's actually not needed: we only set it if
all steps are successful. While at it, rename the label so this confusion
doesn't happen again.
Fixes: 03cea61076 ("drm/i915/dsb: fix extra warning on error path handling")
Resolves: https://gitlab.freedesktop.org/drm/intel/issues/8
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221119.384754-1-lucas.demarchi@intel.com
Use the canonical "[CRTC:%d:%s]" format for the obj id/name
in the debugfs display_info dump. Everyone should already be
familiar with the format since it's used in the debug logs
extensively.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129185434.25549-8-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
No point in repeating the crtc mode for each cloned encoder.
Just print it once, and avoid using multiple lines for it.
And while at let's polish the fixed mode print to fit on
one line as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129185434.25549-6-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
The bspec tells us 'Program SHPD_FILTER_CNT with the "500 microseconds
adjusted" value before enabling hotplug detection' on CNP+. We haven't
been touching this register at all thus far, but we should probably
follow the bspec's guidance.
The register also exists on LPT and SPT, but there isn't any specific
guidance I can find on how we should be programming it there so let's
leave it be for now.
Bspec: 4342
Bspec: 31297
Bspec: 8407
Bspec: 49305
Bspec: 50473
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221314.575575-3-matthew.d.roper@intel.com
When looking at SDEISR to determine the connection status of combo
outputs, we should use the phy index rather than the port index.
Although they're usually the same thing, EHL's DDI-D (port D) is
attached to PHY-A and SDEISR doesn't even have bits for a "D" output.
It's also possible that future platforms may map DDIs (the internal
display engine programming units) to PHYs (the output handling on the IO
side) in ways where port!=phy, so let's look at the PHY index by
default.
v2: Rename to intel_combo_phy_connected. (Lucas)
Fixes: 719d240026 ("drm/i915/ehl: Enable DDI-D")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221314.575575-2-matthew.d.roper@intel.com
The South Display is part of the PCH so we should technically be basing
our port detection logic off the PCH in use rather than the platform
generation.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221314.575575-1-matthew.d.roper@intel.com
LPT/WPT only have PCH transcoder A. Make sure we poke at its
chicken register instead of some non-existent register when
FDI is being driven by pipe B or C.
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128182358.14477-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
As the gen6 page directory is written on binding and after every update,
the code ended up duplicated. Refactor the code into a single routine to
share the locking and serialisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191201140916.2128905-1-chris@chris-wilson.co.uk
Now that many threads may try to use the same mmio to flush the global
buffers after updating the PTE, serialise access to the mmio to prevent
concurrent access on gen7.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191130162320.1683424-1-chris@chris-wilson.co.uk
After much hair pulling, resort to preallocating the ppGTT entries on
init to circumvent the apparent lack of PD invalidate following the
write to PP_DCLV upon switching mm between contexts (and here the same
context after binding new objects). However, the details of that PP_DCLV
invalidate are still unknown, and it appears we need to reload the mm
twice to cover over a timing issue. Worrying.
Fixes: 3dc007fe9b ("drm/i915/gtt: Downgrade gen7 (ivb, byt, hsw) back to aliasing-ppgtt")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129201328.1398583-1-chris@chris-wilson.co.uk
Keep the engine awake and so avoid frequent cycling in and out of
powersaving mode to eliminate the unnecessary overhead and speed up the
testing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129222702.1456292-1-chris@chris-wilson.co.uk
As we only cancel the timers asynchronously, they may
still be running on another CPU as we shutdown, raising one last
softirq. So be safe and make sure the tasklet is flushed before
destroying the engine's memory.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129172542.1222810-1-chris@chris-wilson.co.uk
Though the context is closed and so no more requests can be added to the
timeline, retirement can still be removing requests. It can even be
removing the very request we are inspecting and so cause us to wander
into dead links.
Serialise with the retirement by taking the timeline->mutex used for
guarding the timeline->requests list.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112404
Fixes: 4a31741521 ("drm/i915/gem: Refine occupancy test in kill_context()")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129151845.1092933-1-chris@chris-wilson.co.uk
skl_commit_modeset_enables() straight up compares dirty_pipes
with a bitmask of already committed pipes. If we set bits in
dirty_pipes for non-existent pipes that comparison will never
work right. So let's limit ourselves to bits that exist.
And we'll do the same for the active_pipes_changed bitmask.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011200949.7839-5-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Since commit c45e788d95 ("drm/i915/tgl: Suspend pre-parser across GTT
invalidations"), we now disable the advanced preparser on Tigerlake for the
invalidation phase at the start of the batch, we no longer need to emit
the GPU relocations from a second context as they are now flushed inlined.
References: 8a9a982767 ("drm/i915: use a separate context for gpu relocs")
References: c45e788d95 ("drm/i915/tgl: Suspend pre-parser across GTT invalidations")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191129124846.949100-1-chris@chris-wilson.co.uk
Implement Wa_1604555607 (set the DS pairing timer to 128 cycles).
FF_MODE2 is part of the register state context, that's why it is
implemented here.
At TGL A0 stepping, FF_MODE2 register read back is broken, hence
disabling the WA verification.
v2: Rebased on top of the WA refactoring (Oscar)
v3: Correctly add to ctx_workarounds_init (Michel)
v4:
uncore read is used [Tvrtko]
Macros as used for MASK definition [Chris]
v5:
Skip the Wa_1604555607 verification [Ram]
i915 ptr retrieved from engine. [Tvrtko]
v6:
Added wa_add as a wrapper for __wa_add [Chris]
wa_add is directly called instead of new wrapper [tvrtko]
BSpec: 19363
HSDES: 1604555607
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Ramalingam C <ramlingam.c@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> [v5]
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128021005.3350-1-ramalingam.c@intel.com
