Add the data file to describe all power domains inside the DRA7XX SoC.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation to comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the data file to describe all clock domains inside the DRA7XX SoC
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation to comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the PRCM MPU registers for DRA7XX platforms
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation to comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This header contains minimal regbits that are currently used in code.
This header has traditionally been autogenerated on OMAP4+ devices but
the autogenerated contents are largely (95%) unused and hence to reduce
unsued data in the kernel this header has been cut down (from the autogen
output) to whatever is currently needed. This is done by running a cleanup
script on top of the existing autogen script.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Ambresh K <ambresh@ti.com>
[paul@pwsan.com: added generation notation in the comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the new defines for DRA7XX CM registers.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation in comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the new defines for DRA7xx prm module registers.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation in the comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
A handful of fixes for 3.11 are still trickling in. These are:
- A couple of fixes for older OMAP platforms
- Another few fixes for at91 (lateish due to European summer vacations)
- A late-found problem with USB on Tegra, fix is to keep VBUS regulator
on at all times
- One fix for Exynos 5440 dealing with CPU detection
- One MAINTAINERS update
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NVob
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A handful of fixes for 3.11 are still trickling in. These are:
- A couple of fixes for older OMAP platforms
- Another few fixes for at91 (lateish due to European summer
vacations)
- A late-found problem with USB on Tegra, fix is to keep VBUS
regulator on at all times
- One fix for Exynos 5440 dealing with CPU detection
- One MAINTAINERS update"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: always enable USB VBUS regulators
ARM: davinci: nand: specify ecc strength
ARM: OMAP: rx51: change musb mode to OTG
ARM: OMAP2: fix musb usage for n8x0
MAINTAINERS: Update email address for Benoit Cousson
ARM: at91/DT: fix at91sam9n12ek memory node
ARM: at91: add missing uart clocks DT entries
ARM: SAMSUNG: fix to support for missing cpu specific map_io
ARM: at91/DT: at91sam9x5ek: fix USB host property to enable port C
'gpmc_irq_start' is mostly used as 'int', and for a variable, do not
suggest to only use 'unsigned' as its type, so use 'int' instead of
'unsigned' for variable 'gpmc_irq_start'.
Also it will fix the related issue (dummy the real world failure):
arch/arm/mach-omap2/gpmc.c:728:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The denominator should be load from INCREMENTOR_DENUMERATOR_RELOAD_OFFSET
rather than INCREMENTER_NUMERATOR_OFFSET.
This is more likely a typo, since INCREMENTER_DENUMERATOR_RELOAD[23:17] is
reserved. It seems that it won't make much trouble without this fix, because
the useful [11:0] bits are mask and set the right value. Anyway, reading
from a right address is better choice.
Signed-off-by: Chen Baozi <baozich@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the cold reset was triggered. It happened due to oposite offsets
of cold/warm flags in PRM_RSTST and PRM_RSTCTRL registers.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the option description to match the other TI SoCs.
This is just a cosmetic change.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McPDM and DMIC only available on OMAP4/5 which no longer boots in legacy
mode.
The code to create the devices in legacy mode can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the hwmod data for the mailbox IP in OMAP5 SoC.
This is needed to be able to enable the OMAP mailbox
support for OMAP5.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Here's a pull request of one patch to avoid conflicts during the merge
window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2mCp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/usb-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
USB nop phy rename via Felipe Balbi <balbi@ti.com>:
Here's a pull request of one patch to avoid conflicts during the merge
window.
* tag 'omap-for-v3.12/usb-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceiv
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Peripheral-only mode got broken in v3.11-rc1 because of unknown reasons.
Change the mode to OTG, in practice that should work equally well even
when/if the regression gets fixed.
Note that the peripheral-only regression is a separate patch, this change
is still correct as the role is handled by hardware.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit b7e2e75a8c ("usb: gadget: drop unused USB_GADGET_MUSB_HDRC")
dropped a config symbol that was unused by the musb core, but it turns
out that board support code still had references to it.
As the core now handles both dual role and host-only modes, we can just
pass MUSB_OTG as mode from board files.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
series involve following modifications:
1) fixing up few things in samsung_pwm_timer clocksource driver,
2) moving remaining Samsung platforms to the new clocksource driver,
3) removing old clocksource driver,
4) adding new multiplatform- and DT-aware PWM driver,
5) moving all Samsung platforms to use the new PWM driver,
6) removing old PWM driver,
7) removing all PWM-related code that is not used anymore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=xmmW
-----END PGP SIGNATURE-----
Merge tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux into next/cleanup
From Tomasz Figa:
Here is the Samsung PWM cleanup series. Particular patches of the series
involve following modifications:
- fixing up few things in samsung_pwm_timer clocksource driver,
- moving remaining Samsung platforms to the new clocksource driver,
- removing old clocksource driver,
- adding new multiplatform- and DT-aware PWM driver,
- moving all Samsung platforms to use the new PWM driver,
- removing old PWM driver,
- removing all PWM-related code that is not used anymore.
* tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux: (684 commits)
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
pwm: samsung: Rename to pwm-samsung-legacy
ARM: SAMSUNG: Remove unused PWM timer IRQ chip code
ARM: SAMSUNG: Remove old samsung-time driver
ARM: SAMSUNG: Move all platforms to new clocksource driver
ARM: SAMSUNG: Set PWM platform data
ARM: SAMSUNG: Add new PWM platform device
ARM: SAMSUNG: Unify base address definitions of timer block
clocksource: samsung_pwm_timer: Handle suspend/resume correctly
clocksource: samsung_pwm_timer: Do not use clocksource_mmio
clocksource: samsung_pwm_timer: Cache clocksource register address
clocksource: samsung_pwm_timer: Correct definition of AUTORELOAD bit
clocksource: samsung_pwm_timer: Do not request PWM mem region
+ v3.11-rc4
Conflicts:
arch/arm/Kconfig.debug
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that all the needed pieces for DRA7 based SoCs' is present, enable
the build support in omap2plus_defconfig
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The soc_ops for dra7xx devices can be completed reused
from the ones used for omap4 and omap5 devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The DRA7xx is a high-performance, infotainment application device,
based on enhanced OMAP architecture integrated on a 28-nm technology.
Since DRA7 is a platform supported only using DT, the cpu detection
is based on the compatibles passed from DT blobs as suggested here
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-July/187712.html
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Describe minimal DT boot machine details for DRA7xx based SoC's. DRA7xx
family is based on dual core ARM CORTEX A15 using GIC as the interrupt controller.
The PRCM and timer infrastructure is reused from OMAP5 and so are the io
descriptor tables.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
All of OMAP5 timer support for clocksource and clockevent is completely
reused across DRA7.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The IO descriptor tables for DRA7 are a complete reuse from OMAP5.
A new dra7xx_init_early() does the base address inits.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The PRCM and MPUSS parts of DRA7 devices are quite identical
to OMAP5 so as to reuse all the existing infrastructure around it.
Makefile updates to do just that.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
This series removes the currently-unused PRCM macros from
arch/arm/mach-omap2.
Basic test logs are available at:
http://www.pwsan.com/omap/testlogs/drop_unused_prcm_macros_v3.11-rc/20130721211401/
Once, years ago, we thought that it would be good to document the PRCM
register bits in the Linux codebase. Most folks in the broader
community did not have access to the same documentation, so we thought
that they might be able to use these bits to fix bugs and improve the
code.
We were also able to autogenerate most of these macros, so it was
thought that defining them in advance would reduce the risk of error,
inconsistencies, and merge conflicts caused when patch sets
incrementally defined them by hand.
Well, nice thoughts. But the first rationale was rendered partially
obsolete when TI started to release public TRM documentation PDFs at
some point in the OMAP3 timeframe. (Despite their weaknesses, TI's
public OMAP TRMs remain the most useful public documentation available
for any ARM Linux SoC -- at least to the extent of my knowledge.) And
then the current Linux development tropism towards
development-by-negative-diffstat obliterated the remainder of the
above two philosophies.
So, for the few, the masochistic, out there who wish to continue
developing TI PRCM code, I would ask that you resurrect any
additionally-needed macros from these commits, rather than writing
them manually. Purely for the sake of a pleasant atavism, perhaps; the
way one appreciates a used bookstore, or a video rental store...
And thanks to the upstream maintainers for being patient while we
adjust.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=91he
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/cleanup-unused-defines' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Removal of unused omap defines via Paul Walmsley <paul@pwsan.com>:
This series removes the currently-unused PRCM macros from
arch/arm/mach-omap2.
Basic test logs are available at:
http://www.pwsan.com/omap/testlogs/drop_unused_prcm_macros_v3.11-rc/20130721211401/
Once, years ago, we thought that it would be good to document the PRCM
register bits in the Linux codebase. Most folks in the broader
community did not have access to the same documentation, so we thought
that they might be able to use these bits to fix bugs and improve the
code.
We were also able to autogenerate most of these macros, so it was
thought that defining them in advance would reduce the risk of error,
inconsistencies, and merge conflicts caused when patch sets
incrementally defined them by hand.
Well, nice thoughts. But the first rationale was rendered partially
obsolete when TI started to release public TRM documentation PDFs at
some point in the OMAP3 timeframe. (Despite their weaknesses, TI's
public OMAP TRMs remain the most useful public documentation available
for any ARM Linux SoC -- at least to the extent of my knowledge.) And
then the current Linux development tropism towards
development-by-negative-diffstat obliterated the remainder of the
above two philosophies.
So, for the few, the masochistic, out there who wish to continue
developing TI PRCM code, I would ask that you resurrect any
additionally-needed macros from these commits, rather than writing
them manually. Purely for the sake of a pleasant atavism, perhaps; the
way one appreciates a used bookstore, or a video rental store...
And thanks to the upstream maintainers for being patient while we
adjust.
* tag 'omap-for-v3.12/cleanup-unused-defines' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP5: PRM/CM: Cleanup unused header
ARM: OMAP4: PRM/CM: Cleanup unused header
ARM: OMAP3: PRM/CM: Cleanup unused header
ARM: OMAP2: PRM/CM: Cleanup unused header
Signed-off-by: Olof Johansson <olof@lixom.net>
- omapdss: compilation fix and DVI fix for PandaBoard
- mxsfb: fix colors when using 18bit LCD bus
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSBMT+AAoJEPo9qoy8lh71q+EP/jALUWxJQUpswFsuhKu6Mubf
IUg9F06EH5D+P5IIUWTE5rU5rtEQVm6ANg3gfTiKmjepxgF0zb/odpFjNmhKiFXu
HKqiJWixi07veAxWUidkF2YEPzmoRHQ7rLCVrE4Tg4n0MOzD43sp6HrNWHY3YN4m
XT+V8ZFN0AyLBQveE70tGjuk8Th+tMb4Xoja6vGhpE4MvQJpdBHu9IencBIVlINW
IXbVTCbApOVSbkLuZkXIivrhbWZQhmIYqDO5/kwgaTI7xpTcYlSzjHrhnbHZ/Lw9
ZNCC6DP63v2PsPwakjSbAyQeFIj8k/iqvlpcGK7p7RHq2vIA/UL1Vr3gN/nNGC+k
/ZeVyGOFfLKWJCvIcVEkQpZcQPg1bJafIEc4DexQc5kKU07GcnLi2bEwY7JezbYm
skmiMTaDN4M4JFBltVy69bW/92Z1b1O2Ei+zulwP39OcgHLTooNqk8Y780EQROSM
enuPtgxWiKjJJ1VJy1p4ZWqIn7mtaXuKsFsdMOC9ClQBpBdxrBw9PtV3rjkht7ov
uU/5YPb/ccuyGW7dRK7zrmMMryaEq/YhJS/XKzT/5Xju2XvZk1XSSTJjvLeFyD3+
Qwh+lYPCHLQM2ICajiAGSPmpwdvTRY9ViexnWESaZNwe8p1if0PIyE/tHpYsAYCy
mzzoatK5N96HjIdrXBPK
=bHE/
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- omapdss: compilation fix and DVI fix for PandaBoard
- mxsfb: fix colors when using 18bit LCD bus
* tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
ARM: OMAP: dss-common: fix Panda's DVI DDC channel
video: mxsfb: fix color settings for 18bit data bus and 32bpp
OMAPDSS: analog-tv-connector: compile fix
The "nop" driver isn't a do-nothing-stub but supports a couple functions
like clock on/off or is able to use a voltage regulator. This patch
simply renames the driver to "generic" since it is easy possible to
extend it by a simple function istead of writing a complete driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The omap_init_rng() routine in devices.c only needs to be
called when there is no device tree present.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A recent patch ef3160c (ARM: OMAP2+: Divorce from local timer API,
2013-03-04) broke the omap build when SMP=n because the TWD functions
are only compiled on SMP=y builds. Stub out the TWD calls when the TWD
isn't built in to to keep everything building.
arch/arm/mach-omap2/built-in.o: In function `omap4_local_timer_init':
dss-common.c:(.init.text+0x1d90): undefined reference to `twd_local_timer_register'
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Panda's DVI connector's DDC pins are connected to OMAP's third i2c bus.
With non-DT, the bus number was 3, and that is what is used in the
dss-common.c which contains the platform data for Panda's DVI.
However, with DT, the bus number is 2. As we now only have DT boot for
Panda, we have to change the bus number to make DVI EDID read
operational.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Register target address to be used for cpgmac is the second device
address space. By default, hwmod picks first address space (0th index)
for register target.
With removal of address space from hwmod and using DT instead, cpgmac
is getting wrong address space for register target.
Fix it by indicating the address space to be used for register target.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Address space is being removed from hwmod database and DT information
in <reg> property is being used. Currently the 0th index of device
address space is used to map for register target address. This is not
always true, eg. cpgmac has it's sysconfig in second address space.
Handle it by specifying index of device address space to be used for
register target. As default value of this field would be zero with
static initialization, existing behaviour of using first address space
for register target while using DT would be kept as such.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
[paul@pwsan.com: use u8 rather than int to save memory]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some hwmods which are marked with HWMOD_INIT_NO_IDLE are left in enabled
state post setup(). When a omap_device gets created for such hwmods
make sure the omap_device and pm_runtime states are also in sync for such
hwmods by doing a omap_device_enable() and pm_runtime_set_active() for the
device.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Memory controllers in OMAP (like GPMC and EMIF) have the hwmods marked with
HWMOD_INIT_NO_IDLE and are left in enabled state post initial setup.
Even if they have drivers missing, avoid idling them as part of
omap_device_late_idle()
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With commit '82702ea11ddfe0e43382e1fa5b66d807d8114916' "ARM: OMAP2+:
Fix serial init for device tree based booting" stubbing out
omap_serial_early_init() for Device tree based booting, there was a
crash observed on AM335x based devices when hwmod does a
_setup_reset() early at boot.
This was rootcaused to hwmod trying to reset console uart while
earlycon was using it. The way to tell hwmod not to do this is to
specify the HWMOD_INIT_NO_RESET flag, which were infact set by the
omap_serial_early_init() function by parsing the cmdline to identify
the console device.
Parsing the cmdline to identify the uart used by earlycon itself seems
broken as there is nothing preventing earlycon to use a different one.
This patch, instead, attempts to populate the requiste flags for hwmod
based on the CONFIG_DEBUG_OMAPxUARTy FLAGS. This gets rid of the need
for cmdline parsing in the DT as well as non-DT cases to identify the
uart used by earlycon.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Mark Jackson <mpfj-list@newflow.co.uk>
Reported-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Avoids the following warning when SMP is off:
warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which
has unmet direct dependencies (CPU_V7 && SMP)
Reported-by: Emilio López <emilio@elopez.com.ar>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
timer API entirely. Doing so will reduce code in ARM core, reduce the
architecture dependencies of our timer drivers, and simplify the code because
we no longer go through an architecture layer that is essentially a hotplug
notifier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=wZbm
-----END PGP SIGNATURE-----
Merge tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From Stephen Boyd:
Now that we have a generic arch hook for broadcast we can remove the
local timer API entirely. Doing so will reduce code in ARM core, reduce
the architecture dependencies of our timer drivers, and simplify the code
because we no longer go through an architecture layer that is essentially
a hotplug notifier.
* tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: smp: Remove local timer API
clocksource: time-armada-370-xp: Divorce from local timer API
clocksource: time-armada-370-xp: Fix sparse warning
ARM: msm: Divorce msm_timer from local timer API
ARM: PRIMA2: Divorce timer-marco from local timer API
ARM: EXYNOS4: Divorce mct from local timer API
ARM: OMAP2+: Divorce from local timer API
ARM: smp_twd: Divorce smp_twd from local timer API
ARM: smp: Remove duplicate dummy timer implementation
Resolved a large number of conflicts due to __cpuinit cleanups, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Omap fixes mostly to deal with the dropping of platform data for omap4,
and to make v7_defconfig bootable on omap4 SDP with nfsroot.
* tag 'omap-for-v3.11/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Provide alias to USB PHY clock
ARM: dts: Add missing vmmc2 regulator for twl
ARM: multi_v7: Enabled omap4430 sdp nfsroot
Cleanup unused parts of the PRM and CM regbit headers leaving only whats
used.
prm-regbits-54xx.h was found to be completely unused and
hence removed.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cleanup unused parts of the PRM and CM regbit headers leaving only whats
used.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cleanup unused parts of the PRM and CM regbit headers leaving only whats
used.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cleanup unused parts of the PRM and CM regbit headers leaving only whats
used.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Till the OMAP clocks are correctly defined in device tree, use
this temporary hack to provide clock alias to the USB PHY clocks.
Without this, USB Host & Ethernet will not be functional with
device tree boots on Panda and uEVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code. It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real use
(and testing) out of the box on hardware.
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJR4PeZAAoJEIwa5zzehBx32qAP/jpyDxoktNImkmm84jlB5HEF
WMY6H4Rc0eI/4oCeMMarSDTjtUGzVNuGlm5AjfT1+NPlIbFPCB5GhuiLkn/OkwIn
QU0PtOkVigs8Z1aKn1SZ1KD+0py1P9aGEzecq8j9Q0OIMNx3AIA4BP+JIAFKgZZT
FsgBbAA5oaCgrNMUlvzdrusfKb4ayHJK0dFJILTp8Ts/T1WkMbVnEibnTvKt+y9U
RcCKQW+fzphOqFrIC1qp31VHkmyFUqiX+conWZEe9TOn233uBumJUjHyNVX6K4AC
vBORPZ1vutWKbzna6gQYwzjH/o4Sx9QcbtNZ3dwHQW+YAN+OJxyewlHN7yn8VUnS
icpJNrLREyOHXIhPAdXrf6SjaEhfT+wV7XJY796tEYuLBTeu65l216CGNCRRc6v2
EBNO8YEqgF6G5DrgiwgqYrzxXLg/kXD+Bqwq2glpfNbmfu9ZIY3VCLBwoiKrDPo5
63RkYHYvjtE6fl73RgETgrLUJxUx4wZ62b/AyfDPbm8uNn6w/tJsXwXKLcfVw8Bc
N5kv9w9LZnzhZkxEtXzPRnHPdEE15mS0JAHoqmpVr2bTo7HBRIlkiUtiNo/ZM+sl
dEJKnkCbBlMBao2jxgPKn4c+nDpUEfnQUgNjFYLUBkiRmOtReVoWKH27KvZ5DJmU
1UeIVcE1QIjPhwnPeRbl
=fKfy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
get in before -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=kO4u
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes and minor defconfig updates that would be good to
get in before -rc1.
* tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
ARM: scu: provide inline dummy functions when SCU is not present
ARM: OMAP4: sleep: build OMAP4 specific functions only for OMAP4
ARM: OMAP2+: timer: initialize before using oh_name
Signed-off-by: Olof Johansson <olof@lixom.net>
Add/move/change conflicts in arch/arm/mach-omap2/Kconfig resolved.
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"ARM: OMAP: build mach-omap code only if needed" moved around the
ARCH_OMAP2PLUS stanza, but accidentally dropped the seleciton of
TI_PRIV_EDMA in the process. Add it back.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
Some OMAP SoCs use this function while others do not, and that
causes a warning when building multi_v7_defconfig. Marking the
function __maybe_unused silences the harmless warning without the
need to add complex #ifdef logic.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
If we build a kernel with CONFIG_ARCH_OMAP2PLUS enabled but all of the
individual SoCs disabled, we run into a large number of link errors
because if incorrect dependencies:
arch/arm/mach-omap2/built-in.o: In function `_add_initiator_dep':
arch/arm/mach-omap2/omap_hwmod.c:691: undefined reference to `clkdm_add_sleepdep' arch/arm/mach-omap2/built-in.o: In function `_del_initiator_dep':
arch/arm/mach-omap2/omap_hwmod.c:720: undefined reference to `clkdm_del_sleepdep' arch/arm/mach-omap2/built-in.o: In function `_enable':
arch/arm/mach-omap2/omap_hwmod.c:2145: undefined reference to `clkdm_in_hwsup'
arch/arm/mach-omap2/omap_hwmod.c:2147: undefined reference to `clkdm_hwmod_enable'
arch/arm/mach-omap2/omap_hwmod.c:2191: undefined reference to `clkdm_hwmod_disable'
arch/arm/mach-omap2/omap_hwmod.c:2146: undefined reference to `clkdm_missing_idle_reporting' arch/arm/mach-omap2/built-in.o: In function `_idle':
arch/arm/mach-omap2/omap_hwmod.c:2235: undefined reference to `clkdm_hwmod_disable' arch/arm/mach-omap2/built-in.o: In function `_shutdown':
arch/arm/mach-omap2/omap_hwmod.c:2338: undefined reference to `clkdm_hwmod_disable' arch/arm/mach-omap2/built-in.o: In function `omap_hwmod_get_context_loss_count':
arch/arm/mach-omap2/omap_hwmod.c:4071: undefined reference to `pwrdm_get_context_loss_count' arch/arm/mach-omap2/built-in.o: In function `omap_pm_clkdms_setup':
arch/arm/mach-omap2/pm.c:114: undefined reference to `clkdm_allow_idle'
arch/arm/mach-omap2/pm.c:117: undefined reference to `clkdm_sleep' arch/arm/mach-omap2/built-in.o: In function `omap2_common_pm_late_init':
arch/arm/mach-omap2/pm.c:294: undefined reference to `omap_voltage_late_init' arch/arm/mach-omap2/built-in.o: In function `omap2_gpio_dev_init':
arch/arm/mach-omap2/gpio.c:133: undefined reference to `pwrdm_can_ever_lose_context'
We can avoid this if we make CONFIG_ARCH_OMAP2PLUS a silent option that
gets enabled any time that one of the SoC versions is enabled.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These are selected by omap4 but used in common omap4/5
SMP code, so building an omap5-only kernel is actually
broken without this patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks into timers/core
Frederic sayed: "Most of these patches have been hanging around for
several month now, in -mmotm for a significant chunk. They already
missed a few releases."
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Platform code used to depend on bootloadres for correctly setting the mux
pin modes. But bootloaders should only set the minimum required mux pins.
So, DSS mux pins are not set in U-Boot anymore and video display is broken
on IGEPv2 when booting with newer U-Boot versions.
Setup the DSS pin muxes to enable display functionality.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We still need video & sound drivers with device tree enabled.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cocci spatch "ptr_ret.spatch"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP runtime PM implementation was removed in v3.0. But one Makefile
line, which was used to tweak CFLAGS, was overlooked. Remove it too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM errata 798181 is applicable for OMAP5 based devices. So enable
the same in the build. Errata extract and workaround information
is as below.
On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not
adequately shooting down all use of the old entries. The
ARM_ERRATA_798181 option enables the Linux kernel workaround
for this erratum which sends an IPI to the CPUs that are running
the same ASID as the one being invalidated.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CPU sleep and resume functions for Cortex-A9 based OMAP4 and
Cortex-A15 based OMAP5 are different. Hence, even though we reuse
most of the remaining file as part of OMAP4/5 consolidation, build
OMAP4 specific sleep/resume operations only for OMAP4. SCU is not used
OMAP5.
This fixes the following build failure with OMAP5 only build:
arch/arm/mach-omap2/built-in.o: In function `scu_gp_set':
arch/arm/mach-omap2/sleep44xx.S:132: undefined reference to `scu_power_mode'
arch/arm/mach-omap2/built-in.o: In function `scu_gp_clear':
arch/arm/mach-omap2/sleep44xx.S:229: undefined reference to `scu_power_mode'
Reported-by: Pekon Gupta <pekon@ti.com>
Reported-by: Vincent Stehlé <v-stehle@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
of_property_read_string_index(...,&oh_name) in omap_dm_timer_init_one
does not alter the value of 'oh_name' even if the relevant function
fails and as 'oh_name' in stack may have a non-zero value, it would
be misunderstood by timer code that DT has specified "ti,hwmod"
property for timer. 'oh_name' in this scenario would be a junk value,
this would result in module not being enabled by hwmod API's for
timer, and in turn crash.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Jon Hunter <jgchunter@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Hotplug changes allowing device hot-removal operations to fail
gracefully (instead of crashing the kernel) if they cannot be
carried out completely. From Rafael J Wysocki and Toshi Kani.
- Freezer update from Colin Cross and Mandeep Singh Baines targeted
at making the freezing of tasks a bit less heavy weight operation.
- cpufreq resume fix from Srivatsa S Bhat for a regression introduced
during the 3.10 cycle causing some cpufreq sysfs attributes to
return wrong values to user space after resume.
- New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
provide information previously available via related_cpus from
Lan Tianyu.
- cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
Tang Yuantian.
- Fix for an ACPICA regression causing suspend/resume issues to
appear on some systems introduced during the 3.4 development cycle
from Lv Zheng.
- ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
Chao Guan, and Zhang Rui.
- New cupidle driver for Xilinx Zynq processors from Michal Simek.
- cpuidle fixes and cleanups from Daniel Lezcano.
- Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk.
- ACPI device power management fixes and cleanups from Fengguang Wu
and Rafael J Wysocki.
- ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
- Fix for the IA-64 issue that was the reason for reverting commit
9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
- Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
(to allow some EC-related breakage to be fixed on some systems).
- Spec-compliant implementation of acpi_os_get_timer() from
Mika Westerberg.
- Modification of do_acpi_find_child() to execute _STA in order to
to avoid situations in which a pointer to a disabled device object
is returned instead of an enabled one with the same _ADR value.
From Jeff Wu.
- Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
Intel Low-Power Subsystems (LPSS) driver and modificaions of that
driver to work around a couple of known BIOS issues from
Mika Westerberg and Heikki Krogerus.
- EC driver fix from Vasiliy Kulikov to make it use get_user() and
put_user() instead of dereferencing user space pointers blindly.
- Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
Toshi Kani.
- Modification of the "runtime idle" helper routine to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows some code bloat
reduction to be done, from Rafael J Wysocki and Alan Stern.
- New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
- PM QoS documentation update from Lan Tianyu.
- Assorted core PM code cleanups and changes from Bernie Thompson,
Bjorn Helgaas, Julius Werner, and Shuah Khan.
- New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
- Minor devfreq cleanups, fixes and MAINTAINERS update from
MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
Wei Yongjun.
- OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
driver updates from Andrii Tseglytskyi and Nishanth Menon.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=VBBq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
Pull ARM updates from Russell King:
"This contains the usual updates from other people (listed below) and
the usual random muddle of miscellaneous ARM updates which cover some
low priority bug fixes and performance improvements.
I've started to put the pull request wording into the merge commits,
which are:
- NoMMU stuff:
This includes the following series sent earlier to the list:
- nommu-fixes
- R7 Support
- MPU support
I've left out the ARCH_MULTIPLATFORM/!MMU stuff that Arnd and I
were discussing today until we've reached a conclusion/that's had
some more review.
This is rebased (and re-tested) on your devel-stable branch because
otherwise there were going to be conflicts with Uwe's V7M work now
that you've merged that. I've included the fix for limiting MPU to
CPU_V7.
- Huge page support
These changes bring both HugeTLB support and Transparent HugePage
(THP) support to ARM. Only long descriptors (LPAE) are supported
in this series.
The code has been tested on an Arndale board (Exynos 5250).
- LPAE updates
Please pull these miscellaneous LPAE fixes I've been collecting for
a while now for 3.11. They've been tested and reviewed by quite a
few people, and most of the patches are pretty trivial. -- Will Deacon.
- arch_timer cleanups
Please pull these arch_timer cleanups I've been holding onto for a
while. They're the same as my last posting, but have been rebased
to v3.10-rc3.
- mpidr linearisation (multiprocessor id register - identifies which
CPU number we are in the system)
This patch series that implements MPIDR linearization through a
simple hashing algorithm and updates current cpu_{suspend}/{resume}
code to use the newly created hash structures to retrieve context
pointers. It represents a stepping stone for the implementation of
power management code on forthcoming multi-cluster ARM systems.
It has been tested on TC2 (dual cluster A15xA7 system), iMX6q,
OMAP4 and Tegra, with processors hitting low-power states requiring
warm-boot resume through the cpu_resume code path"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
ARM: 7775/1: mm: Remove do_sect_fault from LPAE code
ARM: 7777/1: Avoid extra calls to the C compiler
ARM: 7774/1: Fix dtb dependency to use order-only prerequisites
ARM: 7770/1: remove residual ARMv2 support from decompressor
ARM: 7769/1: Cortex-A15: fix erratum 798181 implementation
ARM: 7768/1: prevent risks of out-of-bound access in ASID allocator
ARM: 7767/1: let the ASID allocator handle suspended animation
ARM: 7766/1: versatile: don't mark pen as __INIT
ARM: 7765/1: perf: Record the user-mode PC in the call chain.
ARM: 7735/2: Preserve the user r/w register TPIDRURW on context switch and fork
ARM: kernel: implement stack pointer save array through MPIDR hashing
ARM: kernel: build MPIDR hash function data structure
ARM: mpu: Ensure that MPU depends on CPU_V7
ARM: mpu: protect the vectors page with an MPU region
ARM: mpu: Allow enabling of the MPU via kconfig
ARM: 7758/1: introduce config HAS_BANDGAP
ARM: 7757/1: mm: don't flush icache in switch_mm with hardware broadcasting
ARM: 7751/1: zImage: don't overwrite ourself with a page table
ARM: 7749/1: spinlock: retry trylock operation if strex fails on free lock
ARM: 7748/1: oabi: handle faults when loading swi instruction from userspace
...
These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
have these changes merged through arm-soc. As we proceed to untangle
the dependencies between platform code and driver code, the amount of
changes in this category is fortunately shrinking, for 3.11 we have
16 branches here and 101 non-merge changesets, the majority of which
are for the stedma40 dma engine driver used in the ux500 platform.
Cleaning up that code touches multiple subsystems, but gets rid
of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox
is an intermediate step and is still omap specific at the moment.
Patches exist to generalize the subsystem and add other drivers
with the same API, but those did not make it for 3.11.
Conflicts:
* In cpu-db8500.c results from the removal of the u8500_of_init_devices
function in combination with the split of u8500_auxdata_lookup.
* In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mJsI
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
These changes from 30 individual branches for the most part update device
tree files, but there are also a few source code changes that have crept
in this time, usually in order to atomically move over a driver from
using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once.
There are a few conflicts with the other branches unfortunately:
* in exynos5440.dtsi and kirkwood-6281.dtsi, device nodes are added
from multiple branches. Need to be careful to have the right
set of closing braces as git gets this one wrong.
* In kirkwood.dtsi, one 'ranges' line got split into two lines, while
another line got added. Order of the lines does not matter.
* in sama5d3.dtsi, some cleanup was merged the wrong way, causing
a bogus conflict. We want the 'dmas' and 'dma-names' properties
to get added here.
* Two lines got removed independently in arch/arm/mach-mxs/mach-mxs.c
* Contents get added independently in arch/arm/mach-omap2/cclock33xx_data.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8PtJ
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
These are 18 branches on 9 platforms with board specific changes, mostly
for defconfig files, but nothing really exciting in here.
Since the shmobile platform still uses board files for some of the newer
machines, we get a few changes there as the result of drivers getting
enabled for those boards. This causes some conflicts with contents getting
added from multiple branches in sh-mobile specific files. Renesas is
putting a lot of work into migrating to device-tree based setup, which
will make all those files obsolete in the future and avoid both the
conflicts and the need to have these files in the first place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7bgc
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board specific changes from Arnd Bergmann:
"These are 18 branches on 9 platforms with board specific changes,
mostly for defconfig files, but nothing really exciting in here.
Since the shmobile platform still uses board files for some of the
newer machines, we get a few changes there as the result of drivers
getting enabled for those boards. This causes some conflicts with
contents getting added from multiple branches in sh-mobile specific
files. Renesas is putting a lot of work into migrating to device-tree
based setup, which will make all those files obsolete in the future
and avoid both the conflicts and the need to have these files in the
first place."
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
arm: multi_v7_defconfig: Enable initrd/initramfs support
arm: multi_v7_defconfig: Enable Zynq UART driver
ARM: omap2plus_defconfig: enable USB_PHY and NOP_USB_XCEIV
ARM: OMAP1: nokia770: enable Tahvo
ARM: OMAP3EVM: Marking omap3_evm_display_init() with CONFIG_BROKEN
arm: omap: board-overo: reset GPIO for SMSC911x
ARM: shmobile: BOCK-W: change Ether device name
ARM: ux500: board-mop500: remove unused pin modes
ARM: shmobile: bockw: add MMCIF support
ARM: shmobile: bockw: add SPI FLASH support
ARM: shmobile: bockw: add I2C device support
ARM: shmobile: BOCK-W: add Ether support
ARM: tegra: defconfig updates
ARM: shmobile: bockw defconfig: add MMCIF support
ARM: shmobile: bockw defconfig: add M25P80 support
ARM: shmobile: bockw defconfig: add RTC RX8581 support
ARM: shmobile: marzen: keep local function as static
ARM: shmobile: bockw: add SDHI0 support
ARM: shmobile: marzen: Use INTC External IRQ pin driver for SMSC
ARM: shmobile: lager: support GPIO switches
...
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
This contains cleanups as preparation for other branches adding new
features, we pulled 16 branches for 9 platforms into this one.
Most notable here is the removal of support for ATAGS based OMAP4
systems. Since all OMAP4 machines are fully functional with DT based
booting in 3.10, we can remove a lot of code here.
Also noteworthy is Maxime Ripard's cleanup of the machine descriptors,
which means we need no machine descriptors in a lot more cases and
can boot additional machines by just having the respective device
drivers enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XDJs
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"This contains cleanups as preparation for other branches adding new
features, we pulled 16 branches for 9 platforms into this one.
Most notable here is the removal of support for ATAGS based OMAP4
systems. Since all OMAP4 machines are fully functional with DT based
booting in 3.10, we can remove a lot of code here.
Also noteworthy is Maxime Ripard's cleanup of the machine descriptors,
which means we need no machine descriptors in a lot more cases and can
boot additional machines by just having the respective device drivers
enabled."
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
ARM: picoxcell: remove .nr_irqs reference
ARM: s5p64x0: avoid build warning for uncompress.h
ARM: SAMSUNG: Remove unused plat/regs-watchdog.h header
ARM: SAMSUNG: Remove legacy watchdog reset code
ARM: SAMSUNG: Let platforms use the new watchdog reset driver
ARM: SAMSUNG: Add watchdog reset driver
ARM: SAMSUNG: Use local definitions of watchdog registers
watchdog: s3c2410_wdt: Use local register definitions
ARM: S5P64X0: Use common uncompress.h part for plat-samsung
ARM: SAMSUNG: Consolidate uncompress subroutine
ARM: at91: drop rm9200dk board support
ARM: dts: msm: Fix merge resolution
ARM: OMAP1: Remove dma.h
ARM: OMAP1: Remove legacy irda.h and irda setup from board files
ARM: OMAP1: Remove duplicated DMA channel definitions
ARM: OMAP1: Remove McBSP DMA channel definitions
ARM: OMAP2+: Remove dma.h
ARM: OMAP2+: hwmod: Remove remaining DMA channel definitions
ARM: OMAP2+: Remove duplicated DMA channel definitions
ARM: OMAP2+: Remove AES crypto device DMA channel definitions
...
These are various bug fixes that were not considered important enough
for merging into 3.10. The majority of the ARM fixes are for the OMAP
and at91 platforms, and there is another set of bug fixes for device
drivers that resolve 'randconfig' build errors and that the subsystem
maintainers either did not pick up or preferred to get merged through
the arm-soc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gNDf
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-cricitical bug fixes from Arnd Bergmann:
"These are various bug fixes that were not considered important enough
for merging into 3.10.
The majority of the ARM fixes are for the OMAP and at91 platforms, and
there is another set of bug fixes for device drivers that resolve
'randconfig' build errors and that the subsystem maintainers either
did not pick up or preferred to get merged through the arm-soc tree."
* tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: at91/PMC: use at91_usb_rate() for UTMI PLL
ARM: at91/PMC: fix at91sam9n12 USB FS init
ARM: at91/PMC: at91sam9n12 family has a PLLB
ARM: at91/PMC: sama5d3 family doesn't have a PLLB
ARM: tegra: fix section mismatch in tegra_pmc_parse_dt
ARM: mxs: don't select HAVE_PWM
ARM: mxs: stub out mxs_pm_init for !CONFIG_PM
cpuidle: calxeda: select ARM_CPU_SUSPEND
ARM: mvebu: fix length of ethernet registers in mv78260 dtsi
ARM: at91: cpuidle: Fix target_residency
ARM: at91: fix at91_extern_irq usage for non-dt boards
ARM: sirf: use CONFIG_SIRF rather than CONFIG_PRIMA2 where necessary
clocksource: kona: adapt to CLOCKSOURCE_OF_DECLARE change
X.509: do not emit any informational output
mtd: omap2: allow bulding as a module
[SCSI] nsp32: use mdelay instead of large udelay constants
hwrng: bcm2835: fix MODULE_LICENSE tag
ARM: at91: Change the internal SRAM memory type MT_MEMORY_NONCACHED
ARM: at91: Fix link breakage when !CONFIG_PHYLIB
MAINTAINERS: Add exynos filename match to ARM/S5P EXYNOS ARM ARCHITECTURES
...
commit 20d49e9ccf
(ARM: OMAP5: voltagedomain data: Add OMAP5 voltage domain data)
Introduced dummy volt data for OMAP5 with OMAP4460 voltage information.
However with the fixes introduced in later patches
commit cd8abed1da
(ARM: OMAP2+: Powerdomain: Remove the need to always have a voltdm
associated to a pwrdm)
We are no longer restricted in that respect. Further, OPP voltage
information is supposed to be provided by dts information. This needs
to be added in future patches as various voltage modules are converted
to dts.
This also fixes the build breakage for voltagedomains54xx_data.c when just
OMAP5 SoC is enabled: https://patchwork.kernel.org/patch/2764191/
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Now that the TWD doesn't rely on the local timer API, OMAP can
stop selecting it in Kconfig and relying on the config option to
decide if it should call smp_twd functions.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Separate the smp_twd timers from the local timer API. This will
allow us to remove ARM local timer support in the near future and
gets us closer to moving this driver to drivers/clocksource.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
--------------------------------------
This pull request adds DT and runtime PM to
EDMA ARM private API so it can be used on
DT enabled DaVinci and OMAP platforms.
Also adds DMA channel crossbar mapping
support to be used by DT-enabled platforms
which use it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=h9EO
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.11/soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori:
DaVinci SoC updates for v3.11 - part 2
This pull request adds DT and runtime PM to
EDMA ARM private API so it can be used on
DT enabled DaVinci and OMAP platforms.
Also adds DMA channel crossbar mapping
support to be used by DT-enabled platforms
which use it.
* tag 'davinci-for-v3.11/soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
ARM: edma: Convert to devm_* api
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If AM43x and SMP is selected, OMAP4 & OMAP5 deselected, build error as
follows,
arch/arm/mach-omap2/built-in.o: In function `scu_gp_set':
arch/arm/mach-omap2/sleep44xx.S:131: undefined reference to `omap4_get_scu_base'
arch/arm/mach-omap2/sleep44xx.S:132: undefined reference to `scu_power_mode'
arch/arm/mach-omap2/built-in.o: In function `scu_gp_clear':
arch/arm/mach-omap2/sleep44xx.S:227: undefined reference to `omap4_get_scu_base'
arch/arm/mach-omap2/sleep44xx.S:229: undefined reference to `scu_power_mode'
Resolve it by building sleep44xx.S only for OMAP4 & OMAP5.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable TI EDMA option on OMAP and TI_PRIV_EDMA
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The OMAP Mailbox driver framework is moved out of arch/arm folder
into drivers/mailbox folder, to re-enable building it and also serve
as a baseline for adapting to the new mailbox driver framework. The
changes mainly contain:
- a minor bug fix and cleanup of mach-specific mailbox code
- remove any header dependencies from plat-omap for multi-platform
support
- represent mailbox device data through platform data/hwmod attrs
- move the omap mailbox code out of plat-omap/mach-omapX to
drivers/mailbox folder
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=j0vK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/mailbox-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
From Tony Lindgren:
Move OMAP Mailbox framework to drivers via Suman Anna <s-anna@ti.com>
The OMAP Mailbox driver framework is moved out of arch/arm folder
into drivers/mailbox folder, to re-enable building it and also serve
as a baseline for adapting to the new mailbox driver framework. The
changes mainly contain:
- a minor bug fix and cleanup of mach-specific mailbox code
- remove any header dependencies from plat-omap for multi-platform
support
- represent mailbox device data through platform data/hwmod attrs
- move the omap mailbox code out of plat-omap/mach-omapX to
drivers/mailbox folder
* tag 'omap-for-v3.11/mailbox-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mailbox/omap: move the OMAP mailbox framework to drivers
ARM: OMAP2+: add user and fifo info to mailbox platform data
ARM: OMAP2+: mbox: remove dependencies with soc.h
omap: mailbox: correct the argument type for irq ops
omap: mailbox: call request_irq after mbox queues are allocated
omap: mailbox: check iomem resource before dereferencing it
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
omap-for-v3.11/gpmc-signed branch because of a compile error
it caused. The compile error is fixed in this version.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IxbH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/gpmc-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
From Tony Lindgren:
GPMC suspend patch that was left out of the earlier
omap-for-v3.11/gpmc-signed branch because of a compile error
it caused. The compile error is fixed in this version.
* tag 'omap-for-v3.11/gpmc-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: gpmc: Low power transition support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
OMAP: PM: remove requirement for voltage domain data; remove dummy data
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=KjMH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/pm-voltdomain-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
PM voltage domain clean-up via Kevin Hilman <khilman@linaro.org>:
OMAP: PM: remove requirement for voltage domain data; remove dummy data
* tag 'omap-for-v3.11/pm-voltdomain-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: AM33xx: Remove the unused voltagedomain data
ARM: OMAP2+: Powerdomain: Remove the need to always have a voltdm associated to a pwrdm
Includes an update to Linux 3.10-rc6.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
OMAP: PM: the serial core + driver can no handle no_console_suspend support
without any SoC specific handlding or SoC-specific DT bindings. Remove
the now unused SoC specifics for OMAP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yja+
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/pm-serial-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Serial driver platform init code clean-up via Kevin Hilman <khilman@linaro.org>:
OMAP: PM: the serial core + driver can no handle no_console_suspend support
without any SoC specific handlding or SoC-specific DT bindings. Remove
the now unused SoC specifics for OMAP.
* tag 'omap-for-v3.11/pm-serial-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: omap2+: omap_device: remove no_idle_on_suspend
arm: dts: am33xx: Remove "ti,no_idle_on_suspend" property.
arm: omap2+: serial: remove no_console_suspend support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
patch from the already merged omap-for-v3.11/soc-signed branch.
Also fixes for ti81x booting and revision check updates.
These are based on omap-for-v3.11/soc-signed because of the
am43x dependency to earlier patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRwDlPAAoJEBvUPslcq6VzJQ4P/AuF/HWAm8p+pP/qgkPK7JYF
9UdT+RwvBbXkcx3Hx75qSaHCjWHrVHFXOctFWc/dUePvLiWsh/Krjawu/zHRoWXR
jxZdFogCtQbYPIDBd+YlEasb16uLFioSO3DiaMYJCwrEFO2Iln7/U3YmSnyM/u5M
nkcFVfjmBxdJwLdghXoXRvCtv4LWYDRRyA0v5bWMQmqQCraBs9jzHXRQlpA5332y
UWr1XRvGL/LtHZroKtiItkR1FkM8NeO/7JqP4rmy2+ebXWKeAJRtWdKrjDK8M0/6
1zWy5v3M1BSI8RUAL1TODx/ZIHEDtO5Npy9qxMCUqRK0F/y9/u0w8ibPRZabRaNJ
zqVYQ+0NqD4gQf8bVRFZaSgk9U0ZABVbc6jQn6YCmsF2l0uQqG418DWuDWvahqRC
/oOb1vI7vR/Q0rXESwWtIj2z/IQlKnr+Yo+q01eTDjyIEq6vDiHveEV5+fC3qydn
6mcF4P2N5o6fSSH3E6LW3UIUDplZi4VFYfHyyN6F/hTmyzJvAw8oh05CCOSEEfy1
VAkwI3WRwRaCeSoHsT2d3HOXU/kJvKLNzlb233FTt/B9tH40uoBy1C9iRshCJlG8
SOyPq/0pK4TPajEbPFB/SX3KS2LFNz+iZ94Q7Dpbc4jSDxLodTn89Qm5yQ8g4kYS
ivex2S/X+AceVfekvozl
=4brz
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/soc-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Fix am43x minimal booting as I accidentally left out one
patch from the already merged omap-for-v3.11/soc-signed branch.
Also fixes for ti81x booting and revision check updates.
These are based on omap-for-v3.11/soc-signed because of the
am43x dependency to earlier patches.
* tag 'omap-for-v3.11/soc-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: am33xx id: Add new am33xx specific function to check dev_feature
ARM: OMAP: TI816X: add powerdomains for TI816x
ARM: OMAP2: TI81XX: id: Add cpu id for TI816x ES2.0 and ES2.1
ARM: OMAP2+: AM43x: basic dt support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvsJmAAoJEFBXWFqHsHzOHOIH/jjVCaAFdOskPI4d9qPPAt9C
5o0aJDjerzTm+vH2mbec2507fChaYrLybAypJUj6wDYRf03RhAgPXorY83Y+3WtG
SYz2UWza7MY8GeZv6e9tdrYS3JUSicFXPf8MsOcINsuyIub3dD96z36OqrnWZLFy
uH5V81e4gOHECd4PWIxmhdjwawqmwb/Pqzl0V3+vXi2JM07xrn7/SqlZ7VfUwM2q
DNhu5ugH7FtaFp75YrmTIhp6i+tovguRr0RIt6dnk/9gbJBQnV2Cw2MzdRPT12U5
bC79P7sojkKRtITcq9c1fnUNhkgc0+hS8HoezcQmzKMin6nFmVAh5wQFSlRJMJE=
=mZw+
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx soc changes for 3.11:
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
* tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (29 commits)
ARM: imx_v6_v7_defconfig: Enable Vybrid VF610
ARM: imx_v6_v7_defconfig: Enable imx-wm8962 by default
ARM: clk-imx6qdl: Add clko1 configuration for imx6qdl-sabresd
ARM: imx_v6_v7_defconfig: Enable PWM and backlight options
ARM: imx: Remove mxc specific ulpi access ops
ARM: imx: add initial support for VF610
ARM: imx: add VF610 clock support
ARM: imx_v6_v7_defconfig: enable parallel display
ARM: imx: clk: No need to initialize phandle struct
ARM: imx: irq-common: Include header to avoid sparse warning
ARM: imx: Enable mx6 solo-lite support
ARM: imx6: use common of_clk_init() call to initialize clocks
ARM: imx6q: call of_clk_init() to register fixed rate clocks
ARM: imx: imx_v6_v7_defconfig: Select CONFIG_DRM_IMX_TVE
ARM: i.MX6: clk: add different DualLite MLB clock config
ARM i.MX5: Add S/PDIF clocks
ARM i.MX53: Add SATA clock
ARM: imx6q: clk: add the eim_slow clock
ARM: imx: remove MLB PLL from pllv3
ARM: imx: disable pll8_mlb in mx6q_clks
...
Conflicts:
arch/arm/Kconfig.debug (simple add/add conflict)
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
clkout2 comes out on the pad and is being used by various
external on-board peripherals like, Audio codecs and stuff.
So enable the clkout2 by default during init sequence itself.
Also, add the missing entry of "clkout2_ck" to the clock table.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Represent debugSS clock interface as provided in
CM_WKUP_DEBUGSS_CLKCTRL register, includes
- Clock gate for optional DEBUG_CLKA and DBGSYSCLK
- Clock Mux for TRC_PMD and STM_PMD
- Clock divider for STM and TPIU
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
GPMC is hardware controller for external memory interfaces.
This patch adds suspend/resume support for GPMC driver.
It also preserves GPMC register configurations across device low-power states
in which GPMC hardware can be powered-off.
gpmc_suspend()/gpmc_resume() are called by default by core PM framework as part
of driver's runtime PM callbacks.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On 37xx EVM non-dt boot fails with current mainline,
because of broken GPIO numbering in the board file
that uses hardcoded GPIOs.
So marking omap3_evm_display_init() with CONFIG_BROKEN
for now as suggested by Tony as per the below link:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg90399.html
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The reset GPIO should be set for the SMSC911x, otherwise the controller
will not work and probing will fail. In the case of the tobi-duo
expansion board, the second controller shares the same GPIO, thus no
more changes are required (not tested).
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Layout of DEV_FEATURE register (offset = 0x604) is different
between TI81xx and AM33xx device, so create separate function
which will check for features available on specific AM33xx SoC
and set the flags accordingly.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds required structures for powerdomain initialization on
the ti816x. It is impossible to use omap3430 structures in order to
initialize powerdomains on ti816x, because there are big differences
between PRCM module base address offsets on these CPUs.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently omap3xxx_check_revision() detects ES1.0 and ES1.1 only,
this patch extends it by adding ES2.0 and ES2.1 versions support.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All definitions in arch/arm/mach-omap2/dma.h are removed so it can be
removed now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Last remaining DMA channel definitions in arch/arm/mach-omap2/dma.h
are used only by omap_hwmod_2xxx_3xxx_ipblock_data.c and
omap_hwmod_3xxx_data.c. Remove them by using directly DMA channel number in
hwmod data and drop definitions with a following script:
egrep '#define [OMAP|AM35XX].*DMA' arch/arm/mach-omap2/dma.h | cut -f 1,3 \
| while read i; do \
DEF=`echo $i |cut -d ' ' -f 2`; \
CH=`echo $i |cut -d ' ' -f 3`; \
echo "removing" $DEF; \
sed -i "s/${DEF}/${CH}/" arch/arm/mach-omap2/omap_hwmod_*.c; \
sed -i "/${DEF}/d" arch/arm/mach-omap2/dma.h; \
done
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Many DMA channel definitions in arch/arm/mach-omap2/dma.h have been moved or
redefined in drivers without removing them from dma.h. Remove those with a
script below:
egrep '#define OMAP.*DMA' arch/arm/mach-omap2/dma.h \
|cut -f 1 |cut -d ' ' -f 1-2 | while read -r i; do \
if [ `git grep -c "$i" |wc -l` -gt 1 ]; then \
echo "removing" $i; \
sed -i "/${i}/d" arch/arm/mach-omap2/dma.h; \
fi; \
done
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These became unused after commit 660ffd6
("ARM: OMAP2xxx: hwmod: Convert AES crypto devcie data to hwmod").
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that there is a way to tell the powerdomain core about
missing voltage domain auto-scaling control in SoCs', get rid of the dummy
voltage domain data populated for AM33xx devices.
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Afzal Mohammed <afzal@ti.com> # am335x evm
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The powerdomain framework currently expects all powerdomains to be associated with
a corresponding voltagedomain. For some SoCs' (like the already existing AM33xx
family, or for the upcoming AM437x and DRA7 SoCs') which
do not have a Voltage controller/Voltage Processor (neither the SR I2C
bus to communicate with the PMIC) there is no need for a Powerdomain to have
a voltage domain association since there is no auto-scaling of voltages possible
using the voltage FSM.
Extend the arch operations to add an api which the powerdomain core can
then use to identify if a voltdm lookup and association for a powerdomain
is really needed.
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Afzal Mohammed <afzal@ti.com> # am335x evm
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Bandgap is a device used to measure temperature on electronic
equipments. It is widely used in digital integrated circuits. It is
based on the dependency between silicon voltage and temperature.
This patch introduce HAS_BANDGAP config entry. This config is a boolean
value so that arch code can flag if they feature a bandgap device.
This config entry follows the same idea behind ARCH_HAS_CPUFREQ.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Fabio Stevam <festevam@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the OMAP5 SoC family.
As part of the transition to DT, no board files will be used
for OMAP5. The hwmod data is gradually being transitioned
away from arch/arm/mach-omap2: IRQ, DMA, and memory map data
has been moved to DT. Hopefully the dev_attr and clock role
data will be the next step.
Basic test logs are available here, although not for OMAP5,
since I don't have an OMAP5 board:
http://www.pwsan.com/omap/testlogs/omap5_v3.10/20130608130949/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yK8b
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/omap5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Omap5 SoC data via Paul Walmsley <paul@pwsan.com:
Add support for the OMAP5 SoC family.
As part of the transition to DT, no board files will be used
for OMAP5. The hwmod data is gradually being transitioned
away from arch/arm/mach-omap2: IRQ, DMA, and memory map data
has been moved to DT. Hopefully the dev_attr and clock role
data will be the next step.
Basic test logs are available here, although not for OMAP5,
since I don't have an OMAP5 board:
http://www.pwsan.com/omap/testlogs/omap5_v3.10/20130608130949/
* tag 'omap-for-v3.11/omap5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP5: Remove unused include for ocp2scp
ARM: OMAP5: Enable build and frameowrk initialisations
ARM: OMAP5: voltagedomain data: Add OMAP5 voltage domain data
ARM: OMAP5: hwmod data: Create initial OMAP5 SOC hwmod data
ARM: OMAP5: powerdomain data: Add OMAP54XX data and update the header
ARM: OMAP5: clockdomain data: Add OMAP54XX data and update the header
ARM: OMAP5: SCRM: Add OMAP54XX header file.
ARM: OMAP5: PRCM: Add OMAP54XX local MPU PRCM registers
ARM: OMAP4+: PRCM MPU: Move function prototypes to common header for re-use
ARM: OMAP5: CM: Add OMAP54XX register and bitfield files
ARM: OMAP4+: CM: Move function prototypes to common header for re-use
ARM: OMAP5: PRM: Add OMAP54XX register and bitfield files
ARM: OMAP4+: PRM: Move function prototypes to common header for re-use
Signed-off-by: Olof Johansson <olof@lixom.net>
minimal support for am43x SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3bVH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Omap SoC changes. Mostly improves am33xx support, and adds
minimal support for am43x SoCs.
* tag 'omap-for-v3.11/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: AM43x: SRAM base and size
ARM: OMAP2+: AM43x: GP or HS ?
ARM: OMAP2+: AM43x: early init
ARM: OMAP2+: AM43x: static mapping
ARM: OMAP2+: AM437x: SoC revision detection
ARM: OMAP2+: AM43x: soc_is support
ARM: OMAP2+: AM43x: kbuild
ARM: OMAP2+: AM43x: Kconfig
ARM: OMAP2+: separate out OMAP4 restart
ARM: AM33XX: clk: Add clock node for EHRPWM TBCLK
ARM: OMAP3: clock data: get rid of unused USB host clock aliases and dummies
ARM: OMAP2+: AM33xx: Add missing reset status info to GFX hwmod
+ Linux 3.10-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
OMAP PM cleanups for v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=9SyZ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Omap PM changes via Kevin Hilman <khilman@linaro.org>:
OMAP PM cleanups for v3.10
* tag 'omap-for-v3.11/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4+: PM: Consolidate OMAP4 PM code to re-use it for OMAP5
ARM: OMAP4+: Make secondary_startup function name more consistent
ARM: OMAP4+: PM: Consolidate MPU subsystem PM code for re-use
ARM: OMAP4: PM: Avoid expensive cpu_suspend() path for all CPU power states except off
a big pile of platform init code for things that are already handled by
device tree related code. As am33xx is already device tree based, we
can also remove the same data for am33xx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=K9EM
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Move omap4 over to device tree based booting. This allows us to get rid
a big pile of platform init code for things that are already handled by
device tree related code. As am33xx is already device tree based, we
can also remove the same data for am33xx.
* tag 'omap-for-v3.11/cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: hwmod data: Remove irq entries from mcspi, mmc hwmods
ARM: OMAP4: hwmod data: add DSS data back
ARM: OMAP4: hwmod data: Clean up the data file
ARM: AM33XX: hwmod data: irq, dma and addr info clean up
ARM: OMAP2+: Remove omap4 ocp2scp pdata
ARM: OMAP2+: Remove omap4 pdata for USB
ARM: OMAP2+: Remove omap4 pdata from hsmmc.c
ARM: OMAP2+: Remove legacy mux data for omap4
ARM: OMAP2+: Remove board-omap4panda.c
ARM: OMAP2+: Remove board-4430sdp.c
ARM: OMAP2+: Legacy support for wl12xx when booted with devicetree
Resolved merge conflict due to a fix for 3.10 (the fix is removed since
the code is no longer used -- data comes from device tree).
Signed-off-by: Olof Johansson <olof@lixom.net>
Describe minimal DT boot machine details for AM43x based SoC's. AM43x
SoC's are ARM Cortex-A9 based with one core. AM43x is similar to
AM335x w.r.t L4 PER/WKUP memory map. AM43x has a sync timer, here that
is being used as clocksource, while 1ms dmtimer as clockevent.
Signed-off-by: Ankur Kishore <a-kishore@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Fix memory leaks in the error path.
Also, use platform_device_register_full() to allocate
the platform devices and set platform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support for pm_runtime add to GPMC driver.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables usage of DT property 'gpmc,num-cs' as already documented in
Documentation/devicetree/bindings/bus/ti-gpmc.txt
Though GPMC hardware supports upto 8 chip-selects, but all chip-selects may
not be available for use because:
- chip-select pin may not be bonded out at SoC device boundary.
- chip-select pin-mux may conflict with other pins usage.
- board level constrains.
gpmc,num-cs allows user to configure maximum number of GPMC chip-selects
available for use on any given platform. This ensures:
- GPMC child nodes having chip-selects within allowed range are only probed.
- And un-used GPMC chip-selects remain blocked.(may be for security reasons).
Signed-off-by: Gupta, Pekon <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to call omap_serial_early_init() for device
tree based booting as the ports are initialized based on
the .dts entries.
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit '3b9b10151c6838af52244cec4af41a938bb5b7ec' cleaned up the
data file to remove all irq and dma entries for all hwmods, which
are now populated by DT. But mcspi and mmc irq, dma entries were
retained since MMC, NFS boot was not working. Since it is root caused
to be an issue with only DMA entries [1], irq can be safely removed.
[1] http://www.mail-archive.com/linux-omap@vger.kernel.org/msg90115.html
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This definition corresponds to the L3_OCMC0,
as in case of AM33XX.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
[tony@atomide.com: updated to remove default y]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Minimal early init - PRCM initialization not yet taken care.
Control module is similar (base address, feature register etc.) as
that of AM335x, while PRCM base address is different. Instead of
adding a new header file for AM43x, PRCM base address is added in
AM335x header file as it is similar to it to a large extent.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
[tony@atomide.com: updated to drop am33xx_check_features()]
Signed-off-by: Tony Lindgren <tony@atomide.com>
soc_is support for AM43x family of SoC's. Only variant now is AM437x,
it is made as a subclass of AM43x.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Build pieces that could be reused for AM43x - GIC related, secure
related and common PRCM.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Separate out OMAP4 restart and have it similar to other platforms, in
a different file. Main motive is to reuse omap4-common on platforms
other than OMAP4, like AM43x, even if OMAP4 is deselected (otherwise
would have caused build breakage).
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The itention was probably to make both pointers const but as it is now,
it is just const used twice.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dss_hdmi hwmod is used to create the HDMI audio device for OMAP4+
When we boot the kernel we can silently ignore the failure since the IP
does not exist on them.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It means that the SoC does not have DMIC IP.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It means that the SoC does not have McPDM IP.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SDI driver gets currently the vdds_sdi regulator via omapdss device.
This is not correct, and we'll change the SDI driver to get the
regulator directly via omapdss_sdi.0 device.
This patch changes the rx51 board file to add vdds_dsi supply for
omapdss_sdi.0 device.
Note that the vdds_sdi supply for omapdss device is still left there, as
the current display driver uses it. When both the board files and the
display driver has been changed, we can remove the unused supply.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DPI driver gets currently the vdds_dsi regulator via omapdss device.
This is not correct, and we'll change the DPI driver to get the
regulator directly via omapdss_dpi.0 device.
This patch changes the relevant board files to add vdds_dsi supply for
omapdss_dpi.0 device.
Note that the vdds_dsi supply for omapdss device is still left there, as
the current display driver uses it. When both the board files and the
display driver has been changed, we can remove the unused supply.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
board-cm-t35.c and board-ldp.c contain regulator supply entries for
vdds_dsi. However, the given device name is wrong.
This patch fixes the device name from omapdss_dsi1 to omapdss_dsi.0.
Note that as far as I know, DSI driver is not used on these boards, so
this should not have caused any problems. The DSI block can be used to
generate clock for DPI, though, but that's not enabled for omap3 boards
currently.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3b9b10151c (ARM: OMAP4: hwmod data:
Clean up the data file) removes hwmod data for omap4, including DSS
data. DSS has not yet been converted to DT, so the hwmod data is still
needed.
This patch adds back the DSS parts of the hwmod data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox hardware (in OMAP) uses a queued mailbox interrupt
mechanism that provides a communication channel between processors
through a set of registers and their associated interrupt signals
by sending and receiving messages.
The OMAP mailbox framework/driver code is moved to be under
drivers/mailbox, in preparation for adapting to a common mailbox
driver framework. This allows the build for OMAP mailbox to be
enabled (it was disabled during the multi-platform support).
As part of the migration from plat and mach code:
- Kconfig symbols have been renamed to build OMAP1 or OMAP2+ drivers.
- mailbox.h under plat-omap/plat/include has been split into a public
and private header files. The public header has only the API related
functions and types.
- The module name mailbox.ko from plat-omap is changed to
omap-mailbox.ko
- The module name mailbox_mach.ko from mach-omapX is changed as
mailbox_omap1.ko for OMAP1
mailbox_omap2.ko for OMAP2+
Cc: Tony Lindgren <tony@atomide.com>
[gregkh@linuxfoundation.org: ack for staging part]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@copitl.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
The different generations of OMAP2+ SoCs have almost the same
mailbox IP, but the IP has configurable parameters for number
of users (interrupts it can generate out towards processors)
and number of fifos (the base unidirectional h/w communication
channel). This data cannot be read from any registers, and so
has been added to the platform data.
This data together with the interrupt-type configuration can be
used in properly figuring out the number of registers to save
and restore in the OMAP mailbox driver code.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
The OMAP mailbox platform driver code has been cleaned up to
remove the dependencies with soc.h in preparation for moving
the mailbox code to drivers folder.
The code relied on cpu_is_xxx/soc_is_xxx macros previously to
pick the the right set of mailbox devices and register with the
mailbox driver. This data is now represented in a concise format
and moved to the respective omap_hwmod data files and published
to the driver through the platform data.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
The argument type used in the actual individual omap_mbox_ops
for irqs should be omap_mbox_irq_t instead of omap_mbox_type_t.
Signed-off-by: Suman Anna <s-anna@ti.com>
Add a NULL check for iomem resource in mailbox probe functions.
Signed-off-by: Fernando Guzman Lugo <lugo.fernando@gmail.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
SmartReflex driver interface is natively divided to two parts:
- external SmartReflex interface
- interface between SmartReflex driver and SmartReflex Class
Functions which belong to AVS class interface can use
struct omap_sr* instead of struct voltatedomain*, to provide a
direct connection between SR driver and SR class. This allows
us to optimize and not do additional lookups where none is
required.
sr_enable() and sr_disable() are interface functions between
SR driver and SR class. They are typically used by Class driver
to enable/disable SmartReflex hardware module.
Now they take struct omap_sr* as input parameter.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
SmartReflex driver interface is natively divided to two parts:
- external SmartReflex interface
- interface between SmartReflex driver and SmartReflex Class
Functions which belong to AVS class interface can use
struct omap_sr* instead of struct voltatedomain*, to provide a
direct connection between SR driver and SR class. This allows
us to optimize and not do additional lookups where none is
required.
sr_disable_errgen() and sr_configure_errgen() are interface
functions between SR driver and SR class. They are typically
used by Class driver to configure error generator module during
SmartReflex enable/disable sequence.
Now they take struct omap_sr* as input parameter.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
EHRPWM module requires explicit clock gating of TBCLK from control
module. Hence add TBCLK clock node in clock tree for EHRPWM modules.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
[bigeasy: remove CK_AM33XX]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We don't need multiple aliases for the OMAP USB host clocks and neither
the dummy clocks so remove them.
CC: Paul Walmsley <paul@pwsan.com>
CC: Rajendra Nayak <rnayak@ti.com>
CC: Benoit Cousson <b-cousson@ti.com>
CC: Mike Turquette <mturquette@linaro.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
[paul@pwsan.com: updated against v3.10-rc4]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
GFX has a reset status register (PRM_GFX.RM_GFX_RSTST),
so update the GFX hwmod data with .rstst_off and .st_shift
information.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Include the OMAP5 data files in build. Initialise the voltage, power,
clock domains.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add voltagedomain related data for OMAP54XX SOCs. OMAP4 OPP data is
used for now. OMAP5 OPP data will be added as part of OMAP5 DVFS
support.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Adding the hwmod data for OMAP54xx SOCs.
Additional changes done on top of initial SOC data files.
- The IO resource information like dma request lines, irq number and
ocp address space can be populated via dt blob. So such data is stripped
from OMAP5 SOC hwmod data file.
- SDMA IO resource information is still kept since dmaengine work
is till ongoing. Once the legacy dma platform driver becomes obsolete,
SDMA io space information can be removed.
- The devices like dss, aess, usb which are missing the device tree bindings,
hwmod data is not added since OMAP5 is DT only build. When such devices add
the dt bindings, respective hwmod data can be added along with it.
With above update, we now need about ~2000 loc vs ~6000 loc with previous
version of the patch for OMAP5 hwmod data file. Ofcourse with addition of
few more drivers it can go upto ~2400 loc which is still better than the
earlier version.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the data file to describe all power domains inside the OMAP54XX soc.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Generated es2.0 data]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the data file to describe all clock domains inside the OMAP54XX soc.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Generated es2.0 data]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP5 reuses OMAP4 MPU PRCM IP block which lets us re-use functions.
So move the function prototypes from prcm_mpu44xx.h to prcm_mpu_44xx_54xx.h
header. The suggestion came from Paul Walmsley as part of the
OMAP5 data file review.
This is preparatory patch to add OMAP5 MPU PRCM data file.
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP5 reuses OMAP4 CM IP block which lets us re-use CM1/CM2 functions.
So move the function prototypes from cm1_44xx.h, cm2_44xx.h to
cm_prm44xx_54xx.h header. The suggestion came from Paul Walmsley
as part of the OMAP5 data file review.
This is preparatory patch to add OMAP5 CM data file.
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP5 reuses OMAP4 PRM IP block which lets us re-use PRM functions.
So move the function prototypes from prm44xx.h to prm44xx_54xx.h
header. The suggestion came from Paul Walmsley as part of the
OMAP5 data file review.
This is preparatory patch to add OMAP5 PRM data file.
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Also fixes some CCF-related breakage on OMAP36xx/37xx, affecting DSS
at the very least.
Basic test logs for this branch are here:
http://www.pwsan.com/omap/testlogs/fixes_b_v3.10-rc/20130606093449/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HWUH
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-b-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.10/fixes
More OMAP hwmod and clock fixes for v3.10-rc. Fixes the AM33xx UART2.
Also fixes some CCF-related breakage on OMAP36xx/37xx, affecting DSS
at the very least.
Basic test logs for this branch are here:
http://www.pwsan.com/omap/testlogs/fixes_b_v3.10-rc/20130606093449/
- The IO resource information like dma request lines, irq number and
ocp address space can be populated via dt blob. So such data is stripped
from OMAP4 SOC hwmod data file.
- The devices which are still missing the device tree bindings,
address space entries are not removed yet. When such devices add
the dt bindings, respective address space data can be deleted.
- Also other unnecessary hwmods like firewalls are removed as a part of this.
Since emif was getting registered only because of this firewalls links,
the mpu->emif direct link is added now.
The above update, results in reduction of about ~1650 lines of code.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@linaro.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated for omap44xx_usb_phy_and_pll_addrs, dropped
mcspi and mmc changes to avoid regressions on omap4sdp]
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM33XX only supports DT boot mode and with addition of
extracting module resources like, irq, dma and address space
from DT block, so now we can remove duplicate information from
hwmod data file.
This patch cleanups-up/deletes,
- All references to "omap_hwmod_irq_info" data.
- All references to "omap_hwmod_dma_info" data.
- References to "omap_hwmod_addr_space" of the modules
for which DT node is available with required address
space information.
- For the modules where "sysc" field is not applicable,
we don't need module address space, so remove them as well.
- The hwmod like firewall etc which are not useful are also
deleted.
This cleanup gets us around ~1100 LOC of negative diff.
Patch is boot tested on AM335x-EVM along with below modules -
- Matrix-keypad
- Volume up/down keys
- Ethernet
- RTC
- WDT
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap36xx_pwrdn_clk_enable_with_hsdiv_restore expects the parent hw of
the clock to be a clk_hw_omap. However, looking at cclock3xxx_data.c,
all concerned clock have parent defined as clk_divider. Fix the
function to use clk_divider. Tested with 3.9 on dm3730.
Signed-off-by: Jean-Philippe François <jp.francois@cynove.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The UART2 hwmod structure is pointing to the EDMA channels of UART1,
which doesn't look right. This patch fixes this by making the UART2
hwmod structure to a new structure that lists the EDMA channels to be
used by the UART2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This is omap4+ only and no longer needed as omap4+ can be booted
using device tree.
Also remove the related pdata handling from the driver and the
now unneeded platform_data/omap_ocp2scp.h.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now boot with device tree. If you don't want to update u-boot,
you can boot with appended DTB with the following instructions:
1. Make sure you have the appended DTB support in .config
CONFIG_ARM_APPENDED_DTB=y
CONFIG_ARM_ATAG_DTB_COMPAT=y
CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND=y
2. Build the zImage
$ ARCH=arm CROSS_COMPILE=... make zImage
3. Build the device tree blobs
$ ARCH=arm CROSS_COMPILE=... make dtbs
4. Append the correct panda dtb to zImage
Depending on your hardware it's omap4-panda.dtb, omap4-panda-a4.dtb
or omap4-panda-es.dtb.
$ cat arch/arm/boot/zImage arch/arm/boot/dts/omap4-panda-es.dtb > /tmp/appended
5. Use mkimage to produce the appended device tree uImage
$ mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 \
-n "Linux" -d /tmp/appended /tmp/uImage
Signed-off-by: Tony Lindgren <tony@atomide.com
We can now boot with device tree. If you don't want to update u-boot,
you can boot with appended DTB with the following instructions:
1. Make sure you have the appended DTB support in .config
CONFIG_ARM_APPENDED_DTB=y
CONFIG_ARM_ATAG_DTB_COMPAT=y
CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND=y
2. Build the zImage
$ ARCH=arm CROSS_COMPILE=... make zImage
3. Build the device tree blobs
$ ARCH=arm CROSS_COMPILE=... make dtbs
4. Append the dtb to zImage
$ cat arch/arm/boot/zImage arch/arm/boot/dts/omap4-sdp.dtb > /tmp/appended
5. Use mkimage to produce the appended device tree uImage
$ mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 \
-n "Linux" -d /tmp/appended /tmp/uImage
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without WLAN we cannot switch omap4 to use device tree
only booting. This patch can be reverted when the
binding for wl12xx is added.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: devicetree-discuss@lists.ozlabs.org
Tested-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit a819c4f1 (ARM: OMAP3: PM: Only access IVA if one exists)
changed PM to not access IVA registers on omaps that don't have
them. Turns out we still need to idle iva2 as otherwise
iva2_pwrdm will stay on and block deeper idle states.
It seems that the only part of the reset that may not be needed
is the setting of the iva2 boot mode to idle. But as that register
seems to be there and is harmless if no iva2 is on the SoC, it's
probably safest to do the complete reset.
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
with DT.
Basic build, boot, and PM test logs are here - unfortunately, not for
the DT case yet:
http://www.pwsan.com/omap/testlogs/uart_idle_fix_v3.10-rc/20130519164010/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DRuE
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
Fix the OMAP serial driver to work correctly on OMAP4 when booting
with DT.
* tag 'omap-fixes-a-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
Signed-off-by: Olof Johansson <olof@lixom.net>
With the OMAP serial driver sysc cleanup patches in this series, we can
now remove the hwmod external apis for sysc fiddling.
While at this, also remove unused sysc auto idle api from hwmod code.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
UART IP idle handling now taken care by runtime pm backend(hwmod) indirectly
and OMAP serial driver is also cleaned up accordingly.
So remove the un-used slave idle platforms hooks now.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP UART IP needs software control for slave idle modes based on functional
state of the IP. i.e The IP slave idle settings should be set to 'noidle' when
being used and then put back to 'smart_idle' when unused. Currently this is
handled by the driver with function pointers implemented in platform code.
This however breaks in case of device tree because of missing idle handling
APIs.
Previous patches in this series added a flag HWMOD_SWSUP_SIDLE_ACTIVE which
takes care of the mentioned requirement. Hence add the flag for all UART IPs
to take advantage of feature supported by framework.
Subsequent patches removes the slave idle handling from driver code.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some IPs (like UART) need the sidle mode to be controlled in SW only
while they are active. Once they go inactive, they need the IP to be
put back in HW control so they are also wakeup capable.
The flag HWMOD_SWSUP_SIDLE takes care of IPs which need the sidle
mode to be *always* controlled in SWSUP. We now have a need to control
IPs sidle mode in SWSUP only while its active.
So define a new flag 'HWMOD_SWSUP_SIDLE_ACT' to help the framework
know about these new IP requirements.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_enable_sysc() and _idle_sysc() handle the midle mode programming correctly
and program HWMOD_IDLEMODE_SMART or HWMOD_IDLEMODE_SMART_WKUP respectively
for supported IPs (The ones which support hardware controlled midle modes)
However the same programming logic is missing when it comes to sidle mode
programming. Here they seem to just set HWMOD_IDLEMODE_SMART (Again for the
ones which support hardware controlled sidle modes)
This problem was hidden due to the fact that a call to _enable_wakeup()
in those same functions would overwrite the idlemodes and program them
correctly (to HWMOD_IDLEMODE_SMART_WKUP in the supported cases)
So fix the sidlemode handling correctly in these functions and handle the
_enable_wakeup() for SIDLEMODE supported IPs same as the way its handled
for MIDLEMODE supported ones.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
It is required to enable respective clock-domain before
enabling any clock/module inside that clock-domain.
During common-clock migration, .clkdm_name field got missed
for "clkdiv32k_ick" clock, which leaves "clk_24mhz_clkdm"
unused; so it will be disabled even if childs of this clock-domain
is enabled, which keeps child modules in idle mode.
This fixes the kernel crash observed on AM335xEVM-SK platform,
where clkdiv32_ick clock is being used as a gpio debounce clock
and since clkdiv32k_ick is in idle mode it leads to below crash -
Crash Log:
==========
[ 2.598347] Unhandled fault: external abort on non-linefetch (0x1028) at
0xfa1ac150
[ 2.606434] Internal error: : 1028 [#1] SMP ARM
[ 2.611207] Modules linked in:
[ 2.614449] CPU: 0 Not tainted (3.8.4-01382-g1f449cd-dirty #4)
[ 2.620973] PC is at _set_gpio_debounce+0x60/0x104
[ 2.626025] LR is at clk_enable+0x30/0x3c
Cc: stable@vger.kernel.org # v3.9
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8c8a777 (ARM: OMAP2+: Add function to read GPMC settings from
device-tree) added a device-tree property "gpmc,device-nand" to indicate
is the GPMC child device is NAND. This commit should have updated the
GPMC NAND documentation (Documentation/devicetree/bindings/mtd/gpmc-nand.txt)
to list the property "gpmc,device-nand" as a required property and also
updated the example. However, this property is redundant and not needed
because the GPMC child device node for NAND is called "nand". Therefore,
remove this property.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP devices support various NAND transfer modes.
Currently all device-tree definitions will use the default "prefetch
polled" mode, so this patch enables the transfer mode to be specified
in the device-tree.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes omap2_nand_gpmc_retime() which was used to quirk
some timing values before gpmc_cs_set_timings(). Due to recent changes,
gpmc_cs_set_timings() has evolved so that there is no more need for a
retime function.
To keep the gpmc configuration consistent for legacy board files, this
patch also adds oe_on and we_on to nand_default_timings[] as they
would be by the retime function.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support for OMAP5 is added to the omap_dsp_ctrl_write_boot_addr()
to enable the DSP boot.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove "no_idle_on_suspend" check, since respective
driver should be able to prevent idling of an
omap device whenever required.
Driver's can get same behavior by just returning -EBUSY
from their ->runtime_suspend only during suspend.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Rajendra nayak <rnayak@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
"no_console_suspend" is no longer handled in platform file,
Since the omap serial driver is now adapted to prevent
console UART idleing during suspend.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- Few GPMC fixes and binding doc updates noted after sending
pull requests for the GPMC branch.
- Board fixes for beagle usb host and rx51 spi probe order
- SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error
handling fixes
Then few minor things that are not strictly fixes but are good
to get out of the way:
- Add missing legacy mux registers for am/dm73x gpio
- Add detection for am33xx pg2.1 silicon
- Enable twl4030 audio modules in defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lnij
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Omap fixes for things that were discovered during the merge window:
- Few GPMC fixes and binding doc updates noted after sending
pull requests for the GPMC branch.
- Board fixes for beagle usb host and rx51 spi probe order
- SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error
handling fixes
Then few minor things that are not strictly fixes but are good
to get out of the way:
- Add missing legacy mux registers for am/dm73x gpio
- Add detection for am33xx pg2.1 silicon
- Enable twl4030 audio modules in defconfig
* tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove bogus IS_ERR_OR_NULL checking from id.c
ARM: OMAP4+: omap2plus_defconfig: Enable audio via TWL6040 as module
ARM: OMAP2: AM33XX: id: Add support for new AM335x PG2.1 Si
omap: mux: add AM/DM37x gpios
ARM: OMAP1: DMA: fix error handling in omap1_system_dma_init()
ARM: OMAP2+: omap_device: use late_initcall_sync
ARM: OMAP: RX-51: change probe order of touchscreen and panel SPI devices
ARM: OMAP3: Beagle: Fix USB Host on beagle xM Ax/Bx
ARM: OMAP2+: only WARN if a GPMC child probe function fail
ARM: OMAP2+: only search for GPMC DT child nodes on probe
Documentation: dt: update properties in TI GPMC NAND example
Documentation: dt: update TI GPMC ethernet binding properties
Signed-off-by: Olof Johansson <olof@lixom.net>
* late/fixes:
ARM: OMAP2+: Fix unmet direct dependencies for SERIAL_OMAP
ARM: ux500: always select ABX500_CORE
ARM: SIRF: select SMP_ON_UP only on SMP builds
ARM: SPEAr: conditionalize l2x0 support
ARM: imx: build CPU suspend code only when needed
ARM: OMAP: build SMP code only for OMAP4/5
ARM: tegra: Tegra114 needs CPU_FREQ_TABLE
ARM: default machine descriptor for multiplatform
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull slave-dmaengine updates from Vinod Koul:
"This time we have dmatest improvements from Andy along with dw_dmac
fixes. He has also done support for acpi for dmanegine.
Also we have bunch of fixes going in DT support for dmanegine for
various folks. Then Haswell and other ioat changes from Dave and
SUDMAC support from Shimoda."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
dma: tegra: implement suspend/resume callbacks
dma:of: Use a mutex to protect the of_dma_list
dma: of: Fix of_node reference leak
dmaengine: sirf: move driver init from module_init to subsys_initcall
sudmac: add support for SUDMAC
dma: sh: add Kconfig
at_hdmac: move to generic DMA binding
ioatdma: ioat3_alloc_sed can be static
ioatdma: Adding write back descriptor error status support for ioatdma 3.3
ioatdma: S1200 platforms ioatdma channel 2 and 3 falsely advertise RAID cap
ioatdma: Adding support for 16 src PQ ops and super extended descriptors
ioatdma: Removing hw bug workaround for CB3.x .2 and earlier
dw_dmac: add ACPI support
dmaengine: call acpi_dma_request_slave_channel as well
dma: acpi-dma: introduce ACPI DMA helpers
dma: of: Remove unnecessary list_empty check
DMA: OF: Check properties value before running be32_to_cpup() on it
DMA: of: Constant names
ioatdma: skip silicon bug workaround for pq_align for cb3.3
ioatdma: Removing PQ val disable for cb3.3
...
Commit 6770b211 (ARM: OMAP2+: Export SoC information to userspace)
had some broken return value handling as noted by Russell King:
+ soc_dev = soc_device_register(soc_dev_attr);
+ if (IS_ERR_OR_NULL(soc_dev)) {
+ kfree(soc_dev_attr);
+ return;
+ }
+
+ parent = soc_device_to_device(soc_dev);
+ if (!IS_ERR_OR_NULL(parent))
+ device_create_file(parent, &omap_soc_attr);
This is nonsense. For the first, IS_ERR() is sufficient. For the second,
tell me what error checking is required in the return value of this
function:
struct device *soc_device_to_device(struct soc_device *soc_dev)
{
return &soc_dev->dev;
}
when you've already determined that the passed soc_dev is a valid pointer.
If you read the comments against the prototype:
/**
* soc_device_to_device - helper function to fetch struct device
* @soc: Previously registered SoC device container
*/
struct device *soc_device_to_device(struct soc_device *soc);
if "soc" is valid, it means the "previously registered SoC device container"
must have succeeded and that can only happen if the struct device has been
registered. Ergo, there will always be a valid struct device pointer for
any registered SoC device container. Therefore, if soc_device_register()
succeeds, then the return value from soc_device_to_device() will always be
valid and no error checking of it is required.
Simples. The rule as ever applies here: get to know the APIs your using
and don't fumble around in the dark hoping that you'll get this stuff
right.
Fix it as noted by Russell.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for chip id detection of AM335x PG2.1 Silicon.
Currently omap3xxx_check_revision() detects PG1.0 and PG2.0 only,
this patch extends it by adding PG2.1 Si support.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If DEBUG_LL and earlyprintk are enabled, and omap-serial.c is compiled
as a module, the kernel boot hangs early as the clocks for serial port
are cut while earlyprintk still uses the port.
The problem is a race between the late_initcall for omap_device (which
idles devices that have no drivers) and the late_initcall in
kernel/printk.c which turns off the earlyconsole. Any printks
that happen between this omap_device late initcall and the earlyconsole
late initcall will crash when accessing the UART.
The fix is to ensure the omap_device initcall happens after the
earlyconsole initcall.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9fdca9df (spi: omap2-mcspi: convert to module_platform_driver)
broke the SPI display/panel driver probe on RX-51/N900. The exact cause is
not fully understood, but it seems to be related to the probe order. SPI
communication to the panel driver (spi1.2) fails unless the touchscreen
(spi1.0) has been probed/initialized before. When the omap2-mcspi driver
was converted to a platform driver, it resulted in that the devices are
probed immediately after the board registers them in the order they are
listed in the board file.
Fix the issue by moving the touchscreen before the panel in the SPI
device list.
The patch fixes the following failure:
[ 1.260955] acx565akm spi1.2: invalid display ID
[ 1.265899] panel-acx565akm display0: acx_panel_probe panel detect error
[ 1.273071] omapdss CORE error: driver probe failed: -19
Tested-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Joni Lapilainen <joni.lapilainen@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Beagle xM Rev. Ax/Bx, the USB power enable GPIO logic is
reversed when compared to other revisions i.e. it is
active high instead of active low.
Use the beagle_config.usb_pwr_level flag correctly so that
the power regulator can be configured at runtime.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I badly screwed up the merge in commit 6fa52ed33b ("Merge tag
'drivers-for-linus' of git://git.kernel.org/pub/.../arm-soc") by
incorrectly taking the arch/arm/mach-omap2/* data fully from the merge
target because the 'drivers-for-linus' branch seemed to be a proper
superset of the duplicate ARM commits.
That was bogus: commit ff931c821b ("ARM: OMAP: clocks: Delay clk inits
atleast until slab is initialized") only existed in head, and the
changes to arch/arm/mach-omap2/timer.c from that commit got list.
Re-doing the merge more carefully, I do think this part was the only
thing I screwed up. Knock wood.
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle.
We normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time
we need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc cleanup
series because of interdependencies with timer drivers now moved out
of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes
for Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUYj5U2CrR//JCVInAQLNIRAAvsCtYOmXTxkRBxdtNEUUbkEjx71Se7q0
h9PR8vqlkbYwONkJ8a6j8pKq/WJDmLpHQWg/moBsvlGc6uEVBPBFhCWHs1+yGUzX
GhnJOaIKh3+651hIoXccS+/YZ16e1EAzdCM7+1QegPTldsRGkTOiwXgmR51kmPrz
6cZ8P5MFqMrWIy4XqWhOBbMDCY/An05IHMpniGIamUg2/uB921Z0wNFvDrnsg97u
DsVEwimyCJ0j7aO4TH+fkvsjoGWnIhxPtpaIm8iff6TPRI49deRb3zYpnIONm+oG
/cQrRf3BNW+aiTuRCTEjdBNGtcrYgN6CLWWjzgMhv1itSlX8swBcOhuNJRCGNQRI
v3wL4aEBxUpPGGL8erc2GIW7pe29YC2UEYI2z1X/5MEzYO589zkkG2k+/3HQVUwp
dnYpQxhjRMvh4mcodBJFRjzH1Z7agKUwtoKalAHRRH7r5gJDkpL3zLoMhYPTG5IZ
OwU+aYf+dDxh2kKW0zs8a/qL97UTHjlTRUC9LPoumvJ7LlKeDfzEn7DHUm2gggiu
dO9ye/NF/xEXoDXTl0Qp2wJ6/sbPSLyCYCIMdP/gJjWUiDDqqZ0VRaKL7vE/JWrd
NJ7k5yunX8/kRgfqgRFLDdFnPj1JeYHlmexsq4l9TPbPstoIcbw8u1v9sr8aZF+Z
agh9u4e7QU8=
=HWfp
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle. We
normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time we
need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc
cleanup series because of interdependencies with timer drivers now
moved out of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes for
Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10."
* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
ARM: SPEAr: conditionalize SMP code
ARM: arch_timer: Silence debug preempt warnings
ARM: OMAP: remove unused variable
serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
ata: arasan: remove the need for platform_data
ARM: at91/sama5d34ek.dts: remove not needed compatibility string
ARM: at91: dts: add MCI DMA support
ARM: at91: dts: add i2c dma support
ARM: at91: dts: set #dma-cells to the correct value
ARM: at91: suspend both memory controllers on at91sam9263
irqchip: armada-370-xp: slightly cleanup irq controller driver
irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
irqchip: move IRQ driver for Armada 370/XP
ARM: mvebu: move L2 cache initialization in init_early()
devtree: add binding documentation for sp804
ARM: integrator-cp: convert use CLKSRC_OF for timer init
ARM: versatile: use OF init for sp804 timer
ARM: versatile: add versatile dtbs to dtbs target
...
