Use case range for continuous range to make the code shorter.
The .readable_reg and .writable_reg implementation are exactly the same,
so use a common ltc3676_readable_writeable_reg function instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
read ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.
Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator_desc_list_voltage_linear_range which can be used
by drivers for getting the voltages before regulator is registered.
This may be useful for drivers which need to fetch the voltage
selectors at device-tree parsing callback.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a result of exporting the bd70528 specific locking functions
we no longer need struct bd70528. Remove references to
struct bd70528 from bd70528 regulator.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several lines in an if statement that are not indented
correctly. Fix these by removing the tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
linear range is suitable for this driver, let's convert it to linear range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpiod_get_index_optional can return ERR_PTR, add IS_ERR checking for it.
While at it, also remove a redundant NULL test for gpiod in error path.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we changed all providers to pass descriptors into the core
for enable GPIOs instead of a global GPIO number, delete the support
for passing GPIO numbers in, and we get a cleanup and size reduction
in the core, and from a GPIO point of view we use the modern, cleaner
interface.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_* managed device resources and create a local
struct device *dev variable to simplify the code inside
probe().
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This pushes the handling of inversion semantics and open drain
settings to the GPIO descriptor and gpiolib. All affected board
files are also augmented.
This is especially nice since we don't have to have any
confusing flags passed around to the left and right littering
the fixed and GPIO regulator drivers and the regulator core.
It is all just very straight-forward: the core asks the GPIO
line to be asserted or deasserted and gpiolib deals with the
rest depending on how the platform is configured: if the line
is active low, it deals with that, if the line is open drain,
it deals with that too.
Cc: Alexander Shiyan <shc_work@mail.ru> # i.MX boards user
Cc: Haojian Zhuang <haojian.zhuang@gmail.com> # MMP2 maintainer
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> # OMAP1 maintainer
Cc: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> # EM-X270 maintainer
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # EZX maintainer
Cc: Philipp Zabel <philipp.zabel@gmail.com> # Magician maintainer
Cc: Petr Cvek <petr.cvek@tul.cz> # Magician
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # PXA
Cc: Paul Parsons <lost.distance@yahoo.com> # hx4700
Cc: Daniel Mack <zonque@gmail.com> # Raumfeld maintainer
Cc: Marc Zyngier <marc.zyngier@arm.com> # Zeus maintainer
Cc: Geert Uytterhoeven <geert+renesas@glider.be> # SuperH pinctrl/GPIO maintainer
Cc: Russell King <rmk+kernel@armlinux.org.uk> # SA1100
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> #OMAP1 Amstrad Delta
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the GPIO regulator driver to use decriptors only.
We have to let go of the array gpio handling: the fetched descriptors
are handled individually anyway, and the array retrieveal function
does not make it possible to retrieve each GPIO descriptor with
unique flags. Instead get them one by one.
We request the "enable" GPIO separately as before, and make sure
that this line is requested as nonexclusive since enable lines can
be shared and the regulator core expects this.
Most users of the GPIO regulator are using device tree.
There are two boards in the kernel using the gpio regulator from a
non-devicetree path: PXA hx4700 and magician. Make sure to switch
these over to use descriptors as well.
Cc: Philipp Zabel <p.zabel@pengutronix.de> # Magician
Cc: Petr Cvek <petr.cvek@tul.cz> # Magician
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # PXA
Cc: Paul Parsons <lost.distance@yahoo.com> # hx4700
Cc: Kevin Hilman <khilman@baylibre.com> # Meson
Cc: Neil Armstrong <narmstrong@baylibre.com> # Meson
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It looks like linear range is suitable to describe the voltage table
for rk805 buck1/2:
selector 0 ~ 59: 0.7125V with uV_step = 12500
selector 60 ~ 62: 1.8V with uV_step = 200000
selector 63: 2.3V
With this change, then rk805 buck1/2 can reuse rk808_reg_ops_ranges.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Mark Brown <broonie@kernel.org>
A comma has been accidentally used where a semi-colon was clearly
intended, correct this typo.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RK805 has the following voltage range for the BUCK1 and BUCK2 regulators:
From 0.7125V to 1.45V in 12.5mV steps, 1.8V, 2V, 2.2V and 2.3V
, which corresponds to the following values as per the RK805
datasheet:
000 000: 0.7125V
000 001: 0.725V
……
111 011: 1.45V
111 100: 1.8V
111 101: 2.0V
111 110: 2.2V
111 111: 2.3V
This means that the voltage range is not linear and so RK805 can not
reuse the same regulator_ops structure from RK808.
Fix it by creating a list with the correct supported voltage values
for RK805 BUCK1 and BUCK2 regulators.
Tested on a rv1108-elgin-r1 board that now correctly reports a BUCK2
voltage of 2.2V instead of the unsupported value of 1.4875V.
Fixes: c4e0d344c1 ("regulator: rk808: Add regulator driver for RK805")
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a platform driver, no need to include linux/i2c.h.
Include linux/of.h for of_match_ptr.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator support for max77650. We support all four variants of this
PMIC including non-linear voltage table for max77651 SBB1 rail.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is using devm_regulator_register, so it's not necessary to
store *rdev[3] in struct isl_pmic. Use a local variable instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While at it, also fix indent for rk805_reg_ops and rk805_switch_ops.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below build error:
drivers/regulator/mcp16502.c: In function ‘mcp16502_gpio_set_mode’:
drivers/regulator/mcp16502.c:135:3: error: implicit declaration of function ‘gpiod_set_value’; did you mean ‘gpio_set_value’? [-Werror=implicit-function-declaration]
gpiod_set_value(mcp->lpm, 0);
^~~~~~~~~~~~~~~
gpio_set_value
drivers/regulator/mcp16502.c: In function ‘mcp16502_probe’:
drivers/regulator/mcp16502.c:486:13: error: implicit declaration of function ‘devm_gpiod_get’; did you mean ‘devm_gpio_free’? [-Werror=implicit-function-declaration]
mcp->lpm = devm_gpiod_get(dev, "lpm", GPIOD_OUT_LOW);
^~~~~~~~~~~~~~
devm_gpio_free
drivers/regulator/mcp16502.c:486:40: error: ‘GPIOD_OUT_LOW’ undeclared (first use in this function); did you mean ‘GPIOF_INIT_LOW’?
mcp->lpm = devm_gpiod_get(dev, "lpm", GPIOD_OUT_LOW);
^~~~~~~~~~~~~
GPIOF_INIT_LOW
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since devm_regmap_field_alloc can fail, add error checking for it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since devm_regmap_field_alloc can fail, add error checking for it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like refactoring didn't go well and left ALDO2, DLDO2 and ELDO3
definitions broken for AXP803 - now they are using register address
instead of mask. Fix it by using mask where necessary.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_linear_range arrays and stpmic1_regulator_cfgs are only
accessed by this driver and the values are never changed so make them
static const. regulator_ops variables can also be const.
Also clean up a few empty lines in regulator_linear_range array.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BD70528MWV is an ultra-low Iq general purpose single-chip power
management IC for battery-powered portable devices.
Add support for controlling 3 bucks and 3 LDOs present in
ROHM BD70528.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some scenarios the early stages of the boot chain has configured
regulators to be in a required state, but the later stages has skipped
to inform the RPM about it's requirements.
But as the SMD RPM regulators are being initialized voltage change
requests will be issued to align the voltage with the valid ranges. The
RPM aggregates all parameters for the specific regulator, the voltage
will be adjusted and the "enabled" state will be "off" - and the
regulator is turned off.
This patch addresses this problem by caching the requested enable state,
voltage and load and send the parameters in a batch, depending on the
enable state - effectively delaying the voltage request for disabled
regulators.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing MODULE_DEVICE_TABLE and remove the comma from the
separator on the end of the of_device_id array.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The act8600_sudcdc_voltage_ranges setting does not match the datasheet.
The problems in below entry:
REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000),
1. The off-by-one min_sel causes wrong volatage calculation.
The min_sel should be 192.
2. According to the datasheet[1] Table 7. (on page 43):
The selector 248 (0b11111000) ~ 255 (0b11111111) are 41.400V.
Also fix off-by-one for ACT8600_SUDCDC_VOLTAGE_NUM.
[1] https://active-semi.com/wp-content/uploads/ACT8600_Datasheet.pdf
Fixes: df3a950e4e ("regulator: act8865: Add act8600 support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The modalias is set by the MODULE_DEVICE_TABLE, thus remove redundant
MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Having instance specific copy of desc is enough to support multiple
instance of pwm regulator.
The regulator_ops is never changed so no need to copy it per instance, make
pwm_regulator_voltage_table_ops and pwm_regulator_voltage_continuous_ops
const to ensure they won't be changed.
The pwm_regulator_desc is a template to be copied so also make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a helper allowing to access regulator's regmap.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently rdev is dereferenced when assigning desc before rdev is null
checked, hence there is a potential null pointer dereference on rdev.
Fix this by null checking rdev first.
Detected by CoverityScan, CID#1476031 ("Dereference before null check")
Fixes: 77e3e3b165 ("regulator: axp20x: add software based soft_start for AXP209 LDO3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
