Mandatory rates for 5 and 10 MHz are different from the rates used for
20 MHz in 2.4 GHz mode, as they use OFDM only.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)
Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add regulatory class for 60GHz band, according
to the last specification.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In cfg80211_can_use_iftype_chan(), check for P2P Device
first, and then for netdevs. This doesn't really change
anything but makes the code a bit easier to read since
it may not be obvious for everyone at first that a P2P
device has no netdev.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function converts a (global only!) operating
class to an internal band identifier. This will
be needed for extended channel switch support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.
Also update all the users of this value that David Miller and
I could find to use the new constant.
Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.
As suggested by Jesse Gross.
Compile tested only.
Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit "cfg80211: check radar interface combinations" a regression
was introduced which might lead to NULL dereference if the argument
chan = NULL, which might happen in IBSS/wext case (and probably
others).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a BSS struct is updated, the IEs are currently
overwritten or freed. This can lead to races if some
other CPU is accessing the BSS struct and using the
IEs concurrently.
Fix this by always allocating the IEs in a new struct
that holds the data and length and protecting access
to this new struct with RCU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for reporting and calculating VHT MCSes.
Note that I'm not completely sure that the bitrate
calculations are correct, nor that they can't be
simplified.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function cfg80211_get_p2p_attr() can fail and returns
a negative error code. However, the return type is unsigned
int. The largest positive number is determined by desired_len
variable in the function, which is u16. So changing the return
type to int to allow easy error checking. Also change the type
for the attribute to enum for improved type checking.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[fix indentation, don't use u8 attr variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parsing the P2P attributes can be tricky as their
contents can be split across multiple (vendor) IEs.
Thus, it's not possible to parse them like IEs (by
returning a pointer to the data.) Instead, provide
a function that copies the attribute data into a
caller-provided buffer and returns the size needed
(useful in case the buffer was too small.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A number of places in the mesh code don't check that
the frame data is present and in the skb header when
trying to access. Add those checks and the necessary
pskb_may_pull() calls. This prevents accessing data
that doesn't actually exist.
To do this, export ieee80211_get_mesh_hdrlen() to be
able to use it in mac80211.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh header can have address extension by a 4th
or a 5th and 6th address, but never both. Drop such
frames in 802.11 -> 802.3 conversion along with any
frames that have the wrong extension.
Cc: stable@vger.kernel.org
Reviewed-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow adding central tracing like in mac80211.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.
This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.
Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.
As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
libertas currently calls cfg80211_disconnected() when it is being
brought down. This causes an event to be allocated, but since the
wdev is already removed from the rdev by the time that the event
processing work executes, the event is never processed or freed.
http://article.gmane.org/gmane.linux.kernel.wireless.general/95666
Fix this leak, and other possible situations, by processing the event
queue when a device is being unregistered. Thanks to Johannes Berg for
the suggestion.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: stable@vger.kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ah-hoc IE search code found in the ieee80211_bss_get_ie()
and use cfg80211_find_ie() instead.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To call cfg80211_get_chan_state() we need to lock
the wdev, so we need to lock the wdev_iter mutex
in cfg80211_can_use_iftype_chan(). This needs to
use nested locking for lockdep.
Also, cfg80211_get_chan_state() doesn't actually
use the rdev, so remove that completely including
the lock assertion that isn't needed.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support a P2P device abstraction and
Bluetooth high-speed AMPs, we need to have a way
to identify virtual interfaces that don't have a
netdev associated.
Do this by adding a NL80211_ATTR_WDEV attribute
to identify a wdev which may or may not also be
a netdev.
To simplify things, use a 64-bit value with the
high 32 bits being the wiphy index for this new
wdev identifier in the nl80211 API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
60g band uses different from .11n MCS scheme, so bitrate
should be calculated differently
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Until now, a u16 value was used to represent bitrate value.
With VHT bitrates this becomes too small.
Introduce a new 32-bit bitrate attribute. nl80211 will report
both the new and the old attribute, unless the bitrate doesn't
fit into the old u16 attribute in which case only the new one
will be reported.
User space tools encouraged to prefer the 32-bit attribute, if
available (since it won't be available on older kernels.)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[reword commit message and comments a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add enumerations for both cfg80211 and nl80211.
This expands wiphy.bands etc. arrays.
Extend channel <-> frequency translation to cover 60g band
and modify the rate check logic since there are no legacy
mandatory rates (only MCS is used.)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
devlist_mtx locking is changed to accomodate changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
.connect cannot be handled since the driver scans
and connects on its own. It is up to the driver
then to refuse a connection (with -EBUSY for
example).
Non-fixed channel IBSSes always take a single
channel resource. For example two non-fixed
channel IBSSes always take up 2
num_different_channels, even if they operate on
the same channel at a given point of time.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implements .set_monitor_enabled(wiphy, enabled).
Notifies driver upon change of interface layout.
If only monitor interfaces become present it is
called with 2nd argument being true. If
non-monitor interface appears then 2nd argument
is false. Driver is notified only upon change.
This makes it more obvious about the fact that
cfg80211 supports single monitor channel. Once we
implement multi-channel we don't want to allow
setting monitor channel while other interface
types are running. Otherwise it would be ambiguous
once we start considering num_different_channels.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll need this for proper channel tracking (which
is going to be needed for channel context
accounting and finding matching/active interface
combination).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't validate interface combinations on a stopped
interface. Otherwise we might end up being able to
create a new interface with a certain type, but
won't be able to change an existing interface
into that type.
This also skips some other functions when
interface is stopped and changing interface type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.
Cc: stable@kernel.org
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_calculate_bitrate() doesn't work for MCS
rates 32 or higher, and it has always returned 0
in that case. Warn if it ever really happens.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spatch/coccinelle isn't perfect. It doesn't understand
__aligned(x) and doesn't convert functions it can't parse.
Convert the remaining compare_ether_addr uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
I removed a conversion from scan.c/cmp_bss_core
that appears to be a sorting function.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
My grand plan to allow drivers to gradually move over
to advertising virtual interface combinations and only
enforce with drivers that do want it enforced doesn't
seem to be working out, only Christian ever added the
advertising (to carl9170), nobody else did.
Begin enforcing combinations in cfg80211 so that users
can rely on the information reported about a device.
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless will select a different hardware queue based on the
top 3 bits of the diffserv field, for ipv4. Extend that queue
selection mechanism to ipv6, and make the calls orthogonal.
Signed-off-by: Dave Täht <dave.taht@bufferbloat.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is quite possible to run into a race in bss timeout where
the drivers see the bss entry just before notifying cfg80211
of a roaming event but it got timed out by the time rdev->event_work
got scehduled from cfg80211_wq. This would result in the following
WARN-ON() along with the failure to notify the user space of
the roaming. The other situation which is happening with ath6kl
that runs into issue is when the driver reports roam to same AP
event where the AP bss entry already got expired. To fix this,
move cfg80211_get_bss() from __cfg80211_roamed() to cfg80211_roamed().
[158645.538384] WARNING: at net/wireless/sme.c:586
__cfg80211_roamed+0xc2/0x1b1()
[158645.538810] Call Trace:
[158645.538838] [<c1033527>] warn_slowpath_common+0x65/0x7a
[158645.538917] [<c14cfacf>] ? __cfg80211_roamed+0xc2/0x1b1
[158645.538946] [<c103354b>] warn_slowpath_null+0xf/0x13
[158645.539055] [<c14cfacf>] __cfg80211_roamed+0xc2/0x1b1
[158645.539086] [<c14beb5b>] cfg80211_process_rdev_events+0x153/0x1cc
[158645.539166] [<c14bd57b>] cfg80211_event_work+0x26/0x36
[158645.539195] [<c10482ae>] process_one_work+0x219/0x38b
[158645.539273] [<c14bd555>] ? wiphy_new+0x419/0x419
[158645.539301] [<c10486cb>] worker_thread+0xf6/0x1bf
[158645.539379] [<c10485d5>] ? rescuer_thread+0x1b5/0x1b5
[158645.539407] [<c104b3e2>] kthread+0x62/0x67
[158645.539484] [<c104b380>] ? __init_kthread_worker+0x42/0x42
[158645.539514] [<c151309a>] kernel_thread_helper+0x6/0xd
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse reports:
net/wireless/util.c:499:30: error: cannot size expression
net/wireless/util.c:503:30: error: cannot size expression
This is evidently due to the EXPORT_SYMBOL() of the
bridge_tunnel_header and rfc1042 header variables.
Move them to the end of the file to work around the
sparse issue. The error itself from sparse can be
ignored safely, but since sparse stops parsing at
errors, other issues after this would go undetected.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No other driver ever ended up using this, and
the commit forgot to move the prototype so no
driver could have used it. Revert it, if any
driver shows up and needs it it can be moved
again, but until then it's more efficient to
have it in mac80211 where the only user is.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.
During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.
When setup completes and the peer is authorized, send data directly,
bypassing the AP.
In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
